Toshiba ML3054 User Manual

Download

User’s Manual

Qosmio F50 Series

Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Macrovision License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

FCC information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

EU Conformity Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

VCCI Class B Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Important Safety Information for Computers with TV tuner . . . . . . . . ix

Modem warning notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Japan regulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Instructions for IC CS-03 certified equipment . . . . . . . . . . . . . . . . . . xiii

Notes for Users in Australia and New Zealand . . . . . . . . . . . . . . . . . xiv

Optical disc drive safety instructions. . . . . . . . . . . . . . . . . . . . . . . . xviii

International precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxi

Preface

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxiii

General Precautions

Provide adequate ventilation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxvi

Creating a computer-friendly environment . . . . . . . . . . . . . . . . . . . xxvii

Stress injury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxvii

Heat injury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxvii

Pressure or impact damage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxviii

Mobile phones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxviii

Instruction Manual for Safety and Comfort . . . . . . . . . . . . . . . . . . xxviii

The cautions on use of a Qosmio F50 series computer . . . . . . . . xxviii

Chapter 1 Introduction

Equipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

TOSHIBA Value Added Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14

User’s Manual ii

Utilities and Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16

Optinal accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20

Chapter 2 The Grand Tour

Front with the display closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Left side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Underside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Front with the display open. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

System indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

Optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

Chapter 3 Getting Started

Connecting the AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Opening the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Turning on the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Starting up for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Turning off the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Restarting the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

System Recovery Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

System Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

Chapter 4 Operating Basics

Using the Touch Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

AV Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Using the Fingerprint Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Web Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Using TOSHIBA Face Recognition . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

Using optical disk drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14

Writng CD/DVD on DVD Super Multi drives . . . . . . . . . . . . . . . . . . . 4-18

Media care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30

TV Tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32

Sound system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33

Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35

Wireless communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39

LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-42

Cleaning the computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-44

Moving the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-45

Chapter 5 The Keyboard

Typewriter keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Function keys: F1 … F12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Soft keys: FN key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Hot keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Windows special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

Qosmio F50

User’s Manual iii

Keypad overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Generating ASCII characters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Chapter 6 Power

Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Power indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Battery types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

Care and use of the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Replacing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9

TOSHIBA Password Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11

Power-up modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12

Panel power on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13

System automatic Sleep/Hibernation . . . . . . . . . . . . . . . . . . . . . . . . 6-13

Chapter 7 HW Setup

Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

HW Setup Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

Chapter 8 AV functions

Media Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

Front operation panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

Remote Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5

Using the Remote Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12

Installing/Removing batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13

Set-top box Connection Method and Watching TV on the

Media Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17

Listen to radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19

QosmioEngine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20

Chapter 9 Optional Devices

ExpressCard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2

Bridge media slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

Media care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6

Additional memory module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9

Battery Packs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13

Universal AC Adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13

Battery Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13

USB floppy diskette drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14

eSATA (External Serial ATA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-16

External monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-17

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-18

i.LINK (IEEE1394). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-20

Security lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-22

Chapter 10 Troubleshooting

Problem solving process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

Hardware and system checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3

TOSHIBA support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-25

Qosmio F50

User’s Manual iv

Qosmio F50

Chapter 11

Legal Footnotes

CPU*1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1

Memory (Main System)*2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2

Battery Life*3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3

Hard Disk Drive (HDD) Capacity*4 . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3

LCD*5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3

Graphics Processor Unit ("GPU”)*6 . . . . . . . . . . . . . . . . . . . . . . . . . 11-3

Wireless LAN*7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3

Non-applicable Icons*8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4

Copy Protection*9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4

TV Tuner*10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4

Images*11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4

LCD Brightness and Eye Stain*12. . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4

Safety Use for TV Tuner*13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4

Appendix A Specifications

Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Appendix B Display Controller and Video modes

Display controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Video modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Appendix C Wireless LAN

Card Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Radio Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Supported Frequency Sub-bands. . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Appendix D Bluetooth wireless technology Interoperability

Bluetooth wireless technology and your Health . . . . . . . . . . . . . . . . D-2

Regulatory statements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2

Using Bluetooth

Appendix E AC Power Cord and Connectors

Card from TOSHIBA equipment in Japan . . . . . . D-5

Certification agencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1

Appendix F Usage Restrictions

Glossary

Index

User’s Manual v

Copyright

Disclaimer

Qosmio F50

© 2008 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.

TOSHIBA Qosmio F50 Portable Personal Computer User’s Manual

First edition June 2008 Copyright authority for music, movies, computer programs, databases and

other intellectual property covered by copyright laws belongs to the author or to the copyright owner. Copyrighted material can be reproduced only for personal use or use within the home. Any other use beyond that stipulated above (including conversion to digital format, alteration, transfer of copied material and distribution on a network) without the permission of the copyright owner is a violation of copyright or author's rights and is subject to civil damages or criminal action. Please comply with copyright laws in making any reproduction from this manual.

Please note that you may infringe the owner's rights protected by the copyright laws if you use the screen mode switching functions (e.g. Wide mode, Wide Zoom mode, etc.) of this product to display enlarged images/video at coffee shops or hotels for the purposes of profits or providing these to the public.

This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the TOSHIBA Qosmio F50 Portable Personal Computers at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice. TOSHIBA assumes no liability for damages incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manual.

User’s Manual vi

Trademarks

IBM is a registered trademark and IBM PC is a trademark of International Business Machines Corporation.

Intel, Intel SpeedStep, Intel or registered trademarks of Intel Corporation.

Windows, Microsoft and Windows Vista Microsoft Corporation.

Photo CD is a trademark of Eastman Kodak. Bluetooth is a trademark or registered trademark owned by its proprietor

and used by TOSHIBA under license. Memory Stick is a registered trademark and i.LINK is a trademark of Sony

Corporation. DVD MovieFactory is a registered trademarks of Ulead Systems, Inc. Labelflash is a trademark of YAMAHA CORPORATION. Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are trademarks of Dolby Laboratories. Dolby Home Theater is a trademark of Dolby Laboratories.

PalmCheck and TouchPad are trademarks of Synaptics Incorporated. ExpressCard is a trademark of PCMCIA. ConfigFree is a trademark of Toshiba Corporation. Wi-Fi is a registered trademark of the Wi-Fi Alliance. Secure Digital and SD are trademarks of SD Card Association. MultiMediaCard and MMC are trademarks of MultiMediaCard Association. xD-Picture Card is a trademark of FUJIFILM Corporation.

Other trademarks and registered trademarks not listed above may be used in this manual.

Qosmio F50

CoreTM, Celeron and Centrino are trademarks

are registered trademarks of

Macrovision License

This product includes copyright protection technology and intellectual property that are patented in the U.S. and other countries. These patents are the property of Macrovision Corporation. The use of copyright protection must be authorized by Macrovision Corporation. It is intended for home and other restricted-use applications, unless Macrovision Corporation expressly authorizes otherwise. All forms of reverse engineering or decompiling are forbidden.

User’s Manual vii

FCC information

FCC notice "Declaration of Conformity Information"

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

■ Reorient or relocate the receiving antenna.

■ Increase the separation between the equipment and receiver.

■ Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

■ Consult the dealer or an experienced radio/TV technician for help.

Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port, Universal Serial Bus (USB 2.0) ports, i.LINK (IEEE1394) port, HDMI out port and microphone jack. Changes or modifications made to this equipment, not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user’s authority to operate the equipment.

Qosmio F50

FCC conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Contact

Address: TOSHIBA America Information Systems, Inc.

9740 Irvine Boulevard Irvine, California 92618-1697

Telephone: (949) 583-3000

User’s Manual viii

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC and/or R&TTE Directive 1999/5/EC.

Responsible for CEmarking:

manufacturer: Toshiba Corporation, 1-1 Shibaura 1-chome,

The complete official EU CE Declaration can be obtained on following internet page: http://epps.toshiba-teg.com/

VCCI Class B Information

Qosmio F50

TOSHIBA EUROPE GMBH, Hammfelddamm 8, 41460 Neuss, Germany.

Minato-ku, Tokyo, 105-8001, Japan

Important Safety Information for Computers with TV tuner

IEC60950-1/EN60950-1 Information technology equipment - Safety Coaxial cable connection to this computer must only be used if the cable outer conductive shielding has been grounded by the cable installer at the building premises as close to the point of cable entrance, or attachment, as practicable and the connection complies with all local cable installation requirements that are applicable in your area.

User’s Manual ix

Modem warning notice

This information is applicable to the models equipped with a built-in modem.

Conformity Statement

The equipment has been approved to [Commission Decision “CTR21”] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN).

However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.

In the event of problems, you should contact your equipment supplier in the first instance.

Network Compatibility Statement

This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.

Germany ATAAB AN005, AN006, AN007, AN009, AN010

Greece ATAAB AN005, AN006 and GR01, 02, 03, 04 Portugal ATAAB AN001, 005, 006, 007, 011 and

Spain ATAAB AN005, 007, 012, and ES01 Switzerland ATAAB AN002 All other countries/regions ATAAB AN003, 004

Specific switch settings or software setup is required for each network, please refer to the relevant sections of the user guide for more details.

The hookflash (timed break register recall) function is subject to separate national type approvals. It has not been tested for conformity to national type regulations, and no guarantee of successful operation of that specific function on specific national networks can be given.

Qosmio F50

and DE03, 04, 05, 08, 09, 12, 14, 17

P03, 04, 08, 10

Japan regulations

Region selection

If you are using the computer in Japan, technical regulations described under Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection.

User’s Manual x

Redial

TE-2005/174

Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer. Japan’s Telecommunications Business Law permits up to two redials on analogue telephones, but the redials must be made within a total of three minutes. The internal modem is approved by the Japan Approvals Institute for Telecommunications Equipment.

A05-0413001

This label is located on the module.

Qosmio F50

SUBTEL 3061 IC: 109AH-ML3054 TEC/WR/I/MOD-08/02/100.JAN 05 MOROCCO : 2903/2005

FCC NO.:US:S56MD01B13054 Model Number:ML3054

NYCE/CT/0008/06/TS Cofetel n° : TTD:MOML06-189

POSTEL

02375/POSTEL/2007

Name of permit owner: Ronny Cabouly Telephone: 03-9506328 Model: ML3054 Manufacturer: MOTOROLA INC. Country of manufacture: USA Type approval No.: 7-12840-0-101926 Valid from: 2004 Permit No.: 13-12840-0-101927 Valid from:2004

MOTOROLA ML3054 54-3708 MOTOROLA

No.#SL405007

Delphi D40

Agere Systems Delphi Modem D40 Approval No. 3785

ETISALAT PERMIT NO.:E05/01/254/G

User’s Manual xi

04604/POSTEL/2007

Certificate No.#SL405083

E04/01/211/G

EQUIPO HOMOLOGADO POR ANTEL No de Aprob: MC-108 Fecha: 20/12/2005 Empresa: Motorola Inc

Made In China

Complies with

IDA Standards

DA 103255

A05-0025001

B93M1015-F

TE-2004/175

N723Z218

This Agere Delphi D40 56K

Modem may be connected to the Telecom Network

PTC 211/05/074

1911

Morocco: 2514/2005

No:ESD-CPE-0500938

Factory ID: E

Agere DELPHI D40(AM5) 54-5681 Agere Systems Inc.

Approval by PTA,2007

0455-06-2565

NCG-CE-06-009 TEC/WR/I/MOD-08/02/122.MAY07

IC:4005B-DELPHI, REN:0.1

AM5

A05-0413001

N723

0107898349890382

115/06

ASI-DELPHI-D40

TE-A22/K012-04-0422

NTC

Type Approved No.:ESD-CPE-0400760

US:AGSMD01BDELPHI

0617-05-1699

E253445

This Motorola ML3054 56k Modem may be connected to the Telecom Network

PTC / 211 / 05 / 005

NYCE/CT/0003/07/TS

Cofetel n : TTDAGDE07-056

CCAC07M10010T6

Approved by PTA (2004)

Pakistan Telecom Authority

TE-2005/174

Pursuant to FCC CFR 47, Part 68:

When you are ready to install or use the modem, call your local telephone company and give them the following information:

■ The telephone number of the line to which you will connect the modem

■ The registration number that is located on the device

The FCC registration number of the modem will be found on either the device which is to be installed, or, if already installed, on the bottom of the computer, separate from the system information label.

■ The Ringer Equivalence Number (REN) of the modem, which can vary -

for the REN, please refer to the modem's label.

The modem connects to the telephone line by means of a standard jack called the USOC RJ11C.

Type of service

Your modem is designed to be used on standard-device telephone lines. Connection to telephone company-provided coin service (central office implemented systems) is prohibited. Connection to party lines service is subject to state tariffs. If you have any questions about your telephone line, such as how many pieces of equipment you can connect to it, the telephone company will provide this information upon request.

Telephone company procedures

The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice in writing to allow you to make any changes necessary to maintain uninterrupted service.

Qosmio F50

If problems arise

If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone network. If the telephone company notes a problem, they may temporarily discontinue service. When practical, they will notify you in advance of this disconnection. If advance notice is not feasible, you will be notified as soon as possible. When you are notified, you will be given the opportunity to correct the problem and informed of your right to file a complaint with the FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.

Disconnection

If you should ever decide to permanently disconnect your modem from its present line, please call the telephone company and let them know of this change.

User’s Manual xii

Fax branding

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such a message clearly contains in a margin at the top or bottom of each transmitted page, or on the first page of the transmission, the date and time it is sent, an identification of the business, other entity or individual sending the message and the telephone number of the sending machine or such business, other entity or individual. In order to program this information into your fax modem, you should complete the setup of your fax software before sending messages.

Use only No. 26 AWG or larger telecommunication line cord.

Instructions for IC CS-03 certified equipment

1. The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection.

The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Qosmio F50

Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

2. The user manual of analog equipment must contain the equipment’s Ringer Equivalence Number (REN) and an explanation notice similar to the following:

The Ringer Equivalence Number (REN) of the modem can vary - for the REN, please refer to the modem's label.

User’s Manual xiii

The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

3. The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C. The IC registration number of the modem is shown below.

Canada: 4005B-DELPHI

Notes for Users in Australia and New Zealand

Modem warning notice for Australia

Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region settings while the modem is attached to the Australian PSTN would result in your modem being operated in a non-compliant manner. To verify that the country/region is correctly set, enter the command ATI which displays the currently active setting.

To set the country/region permanently to Australia, enter the following command sequence:

AT%T E=1 ATS133=1 AT&F AT&W AT%T E=0 ATZ

Failure to set the modem to the Australia country/region setting as shown above will result in the modem being operated in a non-compliant manner. Consequently, there would be no permit in force for this equipment, with the Telecoms Act 1991 prescribing a penalty of $12,000 for the connection of non-permitted equipment.

Qosmio F50

User’s Manual xiv

Notes for use of this device in New Zealand

■ The grant of a Telepermit for a device in no way indicates Telecom

acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers. Failure to operate should not be reported as a fault to Telecom.

■ In addition to satisfactory line conditions a modem can only work

properly if: a/ It is compatible with the modem at the other end of the call, and; b/ The application using the modem is compatible with the application

at the other end of the call - for example, accessing the Internet requires suitable software in addition to a modem.

■ This equipment shall not be used in any manner which could constitute

a nuisance to other Telecom customers.

■ Some parameters required for compliance with Telecom’s PTC

Specifications are dependent on the equipment (PC) associated with this modem. The associated equipment shall be set to operate within the following limits for compliance with Telecom Specifications:

a/ There shall be no more than 10 call attempts to the same number

within any 30 minute period for any single manual call initiation, and;

b/ The equipment shall go on-hook for a period of not less than 30

seconds between the end of one attempt and the beginning of the next, and;

c/ Automatic calls to different numbers shall be not less than 5

seconds apart.

■ Immediately disconnect this equipment should it become physically

damaged, and arrange for its disposal or repair.

■ The correct settings for use with this modem in New Zealand are as

follows:

ATB0 (CCITT operation) AT&G2 (1800Hz guard tone) AT&P1 (decadic dialing make-break ratio =33%/67%) ATS0=0 (disable auto answer) ATS6=4 (blind dial delay) ATS7=Less than 90 (time to wait for carrier after dialing) ATS10=Less than 150 (loss of carrier to hangup delay - the factory default of 15 is recommended) ATS11=90 (DTMF dialing on/off duration in milliseconds) ATX2 (dial tone detect, but not USA call progress detect)

Qosmio F50

User’s Manual xv

Qosmio F50

■ When used in Auto Answer mode, the S0 register must be set with to a

value of either 3 or 4. This ensures:

■ a person calling your modem will hear a short burst of ringing before

the modem answers. This confirms that the call has been successfully switched through the network.

■ caller identification information (which occurs between the first and

second ring cadences) is not destroyed.

■ The preferred method of dialing is to use DTMF tones (ATDT...) as this

is faster and more reliable than pulse (decadic) dialing. If for some reason you must use decadic dialing, your communications program must be set up to record numbers using the following translation table as this modem does not implement the New Zealand “Reverse Dialing” standard.

Number to be dialed: 0 1 2 3 4 5 6 7 8 9 Number to program into computer: 0 9 8 7 6 5 4 3 2 1 Note that where DTMF dialing is used, the numbers should be entered normally.

■ The transmit level from this device is set at a fixed level and because of

this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired.

■ It is recommended that this equipment be disconnected from the

Telecom line during electrical storms.

■ When relocating the equipment, always disconnect the Telecom line

connection before the power connection, and reconnect the power first.

■ This equipment may not be compatible with Telecom Distinctive Alert

cadences and services such as FaxAbility.

NOTE THAT FAULT CALLOUTS CAUSED BY ANY OF THE ABOVE CAUSES MAY INCUR A CHARGE FROM TELECOM

General conditions

As required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications.

The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork. The Telepermit may not be assigned to other parties or other products without Telecom approval.

A Telepermit artwork for each device is included from which you may prepare any number of Telepermit labels subject to the general instructions on format, size and color on the attached sheet.

The Telepermit label must be displayed on the product at all times as proof to purchasers and service personnel that the product is able to be legitimately connected to the Telecom network.

User’s Manual xvi

The Telepermit label may also be shown on the packaging of the product and in the sales literature, as required in PTC 100.

The charge for a Telepermit assessment is $337.50. An additional charge of $337.50 is payable where an assessment is based on reports against non-Telecom New Zealand Specifications. $112.50 is charged for each variation when submitted at the same time as the original.

An invoice for $NZ1237.50 will be sent under separate cover.

Following information is only for EU-member states:

The use of the symbol indicates that this product may not be treated as household waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

This symbol may not stick depending on the country and region where you purchased.

Disposing of computer and computer batteries

■ Discard this computer in accordance with applicable laws and

regulations. For further information, contact your local government.

■ This computer contains rechargeable batteries. After repeated use, the

batteries will finally lose their ability to hold a charge and you will need to replace them. Under certain applicable laws and regulation, it may be illegal to dispose of old batteries by placing them in the trash.

■ Please be kind to our shared environment. Check with your local

government authority for details regarding where to recycle old batteries or how to dispose of them properly. This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government.

Qosmio F50

User’s Manual xvii

Optical disc drive safety instructions

Be sure to check the international precautions at the end of this section.

Panasonic

DVD Super Multi UJ870

■ The Super Multi DVD drive employs a laser system. To ensure proper

use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

Location of the required label

SERIAL NO. MANUFACTURED:

COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J.

Qosmio F50

CLASS 1 LASER PRODUCT LASER KLASSE 1

Panasonic Communications Co., Ltd. 1-62, 4-Chome Minoshima, Hakata-Ku Fukuoka, Japan

User’s Manual xviii

Pioneer

Super Multi DVD DVR-TD08TBA/ DVR-TD08TBC

■ The Super Multi DVD drive employs a laser system. To ensure proper

use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

Location of the required label

SERIAL NO. MANUFACTURED:

COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J.

CLASS 1 LASER PRODUCT LASER KLASSE 1

PIONEER CORPORATION 4-1, MEGURO 1-CHOME MEGURO-KU, TOKYO, 153-8654

Qosmio F50

User’s Manual xix

Hitach-LG Data Storage

Super Multi DVD GSA-T50N/ GSA-T50F

■ The Super Multi DVD drive employs a laser system. To ensure proper

use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

Location of the required label

SERIAL NO. MANUFACTURED:

COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J.

CLASS 1 LASER PRODUCT LASER KLASSE 1

Hitachi-LG Data Storage, Inc. 22-23, Kaigan 3-chome, Minato-ku, Yokyo, 108-0022 Japan

Qosmio F50

User’s Manual xx

International precautions

Qosmio F50

CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.

VORSICHT: Dieses Gerät enthält ein Laser-System und ist als “LASERSCHUTZKLASSE 1 PRODUKT” klassifiziert. Für den richtigen Gebrauch dieses Modells lesen Sie bitte die Bedienungsanleitung sorgfältig durch und bewahren diese bitte als Referenz auf. Falls Probleme mit diesem Modell auftreten, benachrichtigen Sie bitte die nächste “autorisierte Service-Vertretung”. Um einen direkten Kontakt mit dem Laserstrahl zu vermeiden darf das Gerät nicht geöffnet werden.

User’s Manual xxi

ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.

APPARATET BOR KUN ÅBNES AF FAGFOLK MED SÆRLIGT KENDSKAB TIL APPARATER MED LASERSTRÅLER!

Indvendigt i apparatet er anbragt den her gengivne advarselsmækning, som advarer imod at foretage sådanne indgreb i apparatet, at man kan komme til at udsatte sig for laserstråling.

Qosmio F50

OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1.

VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä.

CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS DURCHFÜHREN VON ANDEREN VORGÄNGEN ALS IN DER BEDIENUNGSANLEITUNG BESCHRIEBEN KÖNNEN GEFÄHRLICHE STRAHLENEXPOSITIONEN ZUR FOLGE HABEN.

User’s Manual xxii

Preface

Congratulations on your purchase of the Qosmio F50 series computer. This powerful notebook computer provides excellent expansion capability, includes multimedia functionality, and is designed to provide years of reliable, high-performance computing.

This computer family includes a model with a built-in TV tuner. When you wish to display a TV program or play CD/DVD with this model before Windows starts, touch the TV panel or the CD/DVD panel (or the same panels on the remote control) respectively during Windows startup. When Windows is running, you can display or record a TV program using the My TV feature of Media Center.

This manual tells how to set up and begin using your Qosmio F50 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.

If you are a new user of computers or if you’re new to portable computing, first read over the Introduction and The Grand Tour chapters to familiarize yourself with the computer’s features, components and accessory devices. Then read Getting Started for step-by-step instructions on setting up your computer.

If you are an experienced computer user, please continue reading the preface to learn how this manual is organized, then become acquainted with this manual by browsing through its pages. Be sure to read the Special

features section of the Introduction, to learn about features that are

uncommon or unique to this computer, as well as the section on HW Setup, to understand how to setup and configure these features.

If you are going to install PC Cards or connect external devices such as a monitor, be sure to read Chapter 9, Optional Devices.

Conventions

This manual uses the following formats to describe, identify, and highlight terms and operating procedures.

User’s Manual xxiii

Abbreviations

On first appearance, and whenever necessary for clarity, abbreviations are enclosed in parentheses following their definition. For example: Read Only Memory (ROM). Acronyms are also defined in the Glossary.

Icons

Icons identify ports, dials, and other parts of your computer. The indicator panel also uses icons to identify the components it is providing information on.

Keys

The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, ENTER identifies the ENTER key.

Key operation

Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, CTRL + C means you must hold down CTRL and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.

Qosmio F50

ABC

When procedures require an action such as clicking an icon or entering text, the icon's name or the text you are to type in is represented in the typeface you see to the left.

Display

ABC

Names of windows or icons or text generated by the computer that appear on its display screen are presented in the type face you see to the left.

Messages

Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below.

Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment.

Please read. A note is a hint or advice that helps you make best use of your equipment.

User’s Manual xxiv

Indicates a potentially hazardous situation, which could result in death or serious injury, if you do not follow instructions.

Terminology

This term is defined in this document as follows:

Qosmio F50

Start

HDD or Hard disk drive

The word "Start" refers to the " " button in Microsoft® Windows Vista®.

Some models are equipped with a "Solid State Drive (SSD)" instead of a hard disk drive. In this manual, the word "HDD" or "Hard disk drive" also refers to the SSD unless otherwise stated.

User’s Manual xxv

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer.

Be certain to read the general precautions below and to note the cautions included in the text of the manual.

Provide adequate ventilation

■ Always make sure your Computer and AC adaptor have adequate

ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet (even if your Computer is in Sleep Mode). In this condition, observe the following:

■ Never cover your Computer or AC adaptor with any object.

■ Never place your Computer or AC adaptor near a heat source, such

as anelectric blanket or heater.

■ Never cover or block the air vents including those located at the

base of the Computer.

■ Always operate your Computer on a hard flat surface. Using your

Computer on a carpet or other soft material can block the vents.

■ Always provide sufficient space around the Computer.

■ Overheating your Computer or AC adaptor could cause system failure,

Computer or AC adaptor damage or a fire, possibly resulting in serious injury.

User’s Manual xxvi

Creating a computer-friendly environment

Place the computer on a flat surface that is large enough for the computer and any other items you are using, such as a printer.

Leave enough space around the computer and other equipment to provide adequate ventilation. Otherwise, they may overheat.

To keep your computer in prime operating condition, protect your work area from:

■ Dust, moisture, and direct sunlight.

■ Equipment that generates a strong electromagnetic field, such as

stereo speakers (other than speakers that are connected to the computer) or speakerphones.

■ Rapid changes in temperature or humidity and sources of temperature

change such as air conditioner vents or heaters.

■ Extreme heat, cold, or humidity.

■ Liquids and corrosive chemicals.

Stress injury

Carefully read the Instruction Manual for Safety and Comfort. It contains information on the prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use. Instruction Manual for Safety and Comfort also includes information on work space design, posture and lighting that can help reduce physical stress.

Qosmio F50

Heat injury

■ Avoid prolonged physical contact with the computer. If the computer is

used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer a low-heat injury.

■ If the computer has been used for a long time, avoid direct contact with

the metal plate supporting the various interface ports as this can become hot.

■ The surface of the AC adaptor can become hot when in use but this

condition does not indicate a malfunction. If you need to transport the AC adaptor, you should disconnect it and let it cool before moving it.

■ Do not lay the AC adaptor on a material that is sensitive to heat as the

material could become damaged.

User’s Manual xxvii

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to any form of strong impact as this can damage the computer's components or otherwise cause it to malfunction.

Mobile phones

Please be aware that the use of mobile phones can interfere with the audio system. The operation of the computer will not be impaired in any way, but it is recommended that a minimum distance of 30cm is maintained between the computer and a mobile phone that is in use.

Instruction Manual for Safety and Comfort

All important information on the safe and proper use of this computer is described in the enclosed Instruction Manual for Safety and Comfort. Be sure to read it before using the computer.

The cautions on use of a Qosmio F50 series computer

1. Clean any dust accumulated on the computer's cooling vents. The cooling vents are located on the back and underside of the computer.

Qosmio F50

When you use your computer in a dusty area, dirt and debris may accumulate on the cooling vents at the under side of your unit. If this occurs, the accumulated dust can cause insufficient heat dissipation which may result in the computer shutting down during use. Carefully clean the dust from the vents using a vacuum cleaner.

2. Cooling vents on the underside and back of the computer.

Sub woofer Cooling vent

User’s Manual xxviii

Qosmio F50

The above illustration is of the subwoofer equipped model. Models without the subwoofer have cooling vents in the subwoofer location pictured above. Models with the subwoofer do not have cooling vents in the subwoofer location pictured above.

Cooling vent

Cooling vents

To prevent possible overheating of the CPU, make sure the cooling fan's air intake is not blocked. The fan draws in air by creating a vacuum. If the fan is blocked, it could cause the CPU to run at a lower performance level or cause the computer to shut down. Loose items such as notebook and tissue paper, plastic wrappers, or other similar materials can block the air intake, preventing air from reaching the CPU. Do not use the computer on surfaces with objects that can be drawn in by the cooling fan.

User’s Manual xxix

Introduction

This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories.

Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA.

Equipment checklist

Carefully unpack your computer, taking care to save the box and packaging materials for future use.

Hardware

Check to make sure you have all the following items:

■ Qosmio F50 Portable Personal Computer

■ AC adaptor and power cord (2-pin plug or 3-pin plug)

■ Battery pack (is pre-installed in some computer)

■ Infrared transmitter cable

■ Remote controller (is included with some models)

■ Two AA manganese batteries (for Full size remote controller)

■ CR2016 battery (for Slim size remote controller)

■ Cleaning cloth (is included with some models)

■ FM tuner antenna (is included with some models)

Chapter 1

■ Some models are included with either a Full size remote controller or

Slim size remote controller.

■ Use the cleaning cloth to wipe away dust, fingerprints and similar from

the keyboard, palm rest and other parts. For precautions on use refer to the Using the cleaning cloth section in Chapter 4, Operating Basics.

User’s Manual 1-1

Documentation

■ Qosmio F50 Portable Personal Computer User’s Manual

(User’s Manual)

■ Instruction Manual for Safety and Comfort

■ End User License Agreement

If any of the items are missing or damaged, contact your dealer immediately.

Software

The following Windows® operating system and utility software are pre-installed.

■ Microsoft® Windows Vista

■ TOSHIBA Value Added Package

■ Ulead DVD MovieFactory

■ Fingerprint Utility

■ Windows Mobility Center

■ TOSHIBA Gesture Controller

■ Toshiba Graphical Video Library

■ TOSHIBA HD Console

■ TOSHIBA Face Recognition

■ TOSHIBA Disc Creator

■ TOSHIBA Recovery Disc Creator

■ TOSHIBA ConfigFree

■ TOSHIBA Assist

■ CD/DVD Drive Acoustic Silencer

■ TOSHIBA Password Utility

■ TOSHIBA DVD PLAYER

■ Online Manual

■ Qosmio F50 User’s Manual (This manual)

Introduction

User’s Manual 1-2

Hardware

Introduction

This section describes the hardware of your computer. The actual specifications may vary depending on the model you

purchased.

Processor

Built-in The computer is equipped with one of the

following Intel

■ Intel

incorporates a 3MB level2 cache memory and also supports Enhanced Intel SpeedStep

■ Intel

processor.

CoreTM 2 Duo Processor, which

Technology.

CoreTM 2 Duo Processor, which incorporates a 6MB level2 cache memory and also supports Enhanced Intel SpeedStep Technology.

Some models in this series use Intel® Centrino® 2 processor technology which is based on three separate components, the Intel processor, Intel

WiFi Link 5300AGN-OR-5100AGN and the Intel®

CoreTM 2 Duo

GM/PM45 Express Chipset.

Legal Footnote (CPU)*1

For more information on the CPU, please refer to the Legal Footnotes section in Chapter 11 or click the *1 above.

User’s Manual 1-3

Memory

Introduction

Slots 512, 1,024 or 2,048MB memory modules can be

Video RAM The memory in a computer's graphics adaptor,

installed in the computer's two memory slots for a maximum of 4,096MB system memory. This computer can be equipped with memory modules of a maximum size of 4,096MB. The actual amount of useable system memory will be less than the installed memory modules.

used to store the image displayed on a bitmap display.

Start -> Control Panel -> Appearance and Personalization -> Personalization -> Display Settings.

The amount of Video RAM can be verified by clicking the Advanced Settings... button in the Display Settings window.

The amount of Total Available Graphics memory will vary be between 1 and 2 MB depending upon system configuration.

Legal Footnote (Memory (Main System))*2

For more information regarding Memory (Main System), please refer to the

Legal Footnotes section in Chapter 11 or click the *2 above.

Toshiba Quad Core HD Processor

A co-processor specialized for media streaming processes (real-time image processing such as image processing and image recognition) is installed.

Power

Battery pack The computer is powered by one rechargeable

lithium-ion battery pack.

Legal Footnote (Battery Life)*3

For more information regarding Battery Life, please refer to the Legal

Footnotes section in Chapter 11 or click the *3 above.

User’s Manual 1-4

Introduction

RTC battery The internal RTC battery backs up the Real Time

Clock (RTC) and calendar.

AC adaptor The AC adaptor provides power to the system

and recharges the batteries when they are low. It comes with a detachable power cord which will either have a 2-pin or 3-pin plug enclosure.

As the AC adaptor is universal, it can receive a range of AC voltages from 100 to 240 volts, however you should note that the output current varies among different models. Using the wrong adaptor can damage your computer. Refer to the

AC adaptor section in Chapter 2, The Grand Tour.

Disks

Hard disk drive or Solid state drive

This computer is equipped with the following types of hard disk drive(HDD). The capacity of each hard disk drive model is different.

Some models are equipped with a "Solid State Drive (SSD)" instead of a hard disk drive.

■ HDD

■ 200GB

■ 250GB

■ 320GB

■ 400GB

■ 500GB

■ SSD

■ 64GB

■ 128GB

Two HDD computer models are available, a model with a single hard disk drive and a model with two hard disk drives.

Please note that part of the hard disk drives overall capacity is reserved as administration space.

■ In this manual, the word "HDD" or "Hard disk drive" also refers to the

SSD unless otherwise stated.

■ SSD is a large-capacity storage media which uses Solid-State Memory

in place of a magnetic disk of the hard disk.

■ Under certain unusual conditions of prolonged non-use and/or

exposure to high temperatures, the SSD may be vulnerable to data retention errors.

User’s Manual 1-5

Introduction

Legal Footnote (Hard Disk Drive (HDD) Capacity)*4

For more information regarding Hard Disk Drive (HDD) Capacity, please refer to the Legal Footnotes section in Chapter 11 or click the *4 above.

Optical disc drive

DVD Super Multi drive

The drive reads DVD-ROM's at a maximum 8x speed and CD-ROM's at a maximum 24x speed, and writes CD-R's at up to 16x speed, CD-RW's at up to 10x speed, DVD-R's and DVD+R's at up to 4x speed, DVD-RW's and DVD+RW's at up to 4x speed, DVD-R (Dual layer) at up to 2x speed, DVD+R (Double Layer) at up to 2.4x speed and DVD-RAM at up to 3x speed, and supports the following formats:

■ CD-R

■ CD-RW

■ DVD-ROM

■ DVD-Video

■ CD-DA

■ CD-Text

■ Photo CD™ (single/multi-session)

■ CD-ROM Mode 1, Mode 2

■ CD-ROM XA Mode 2 (Form1, Form2)

■ Enhanced CD (CD-EXTRA)

■ Addressing Method 2

■ DVD-R

■ DVD-R (Dual Layer)

■ DVD-RW

■ DVD+R

■ DVD+R (Double Layer)

■ DVD+RW

■ DVD-RAM

Some models are equipped with a full-size DVD Super Multi drive module that lets you run CD's or DVD's without using an adaptor.

DVD Super Multi drive with Labelflash

User’s Manual 1-6

The drive reads DVD-ROM's at a maximum 8x speed and CD-ROM's at a maximum 24x speed, and writes CD-R's and CD-RW's at up to 24x speed, DVD-R's, DVD+R's and DVD+RW's at up to 8x speed, DVD-RW's, DVD-R (Dual Layer) and DVD+R (Double Layer) at up to 6x speed, DVD-RAM at up to 5x speed. This drive supports the same formats as the DVD Super Multi drive.

Introduction

Display

The computer's internal display panel supports high-resolution video graphics and can be set to a wide range of viewing angles for maximum comfort and readability.

Display panel 15.4" TFT LCD screen, 32 million colors, with a

resolutions

■ 1280 horizontal X 800 vertical pixels WXGA

■ 1440 horizontal X 900 vertical pixels WXGA+

Legal Footnote (LCD)*5

For more information regarding the LCD, please refer to the Legal

Footnotes section in Chapter 11 or click the *6 above.

Graphics controller The graphics controller maximizes display

performance. Refer to the Display Controller and

Video modes section in Appendix B for more

information.

Legal Footnote (Graphics Processor Unit ("GPU"))*6

For more information regarding the Graphics Processor Unit ("GPU"), please refer to the Legal Footnotes section in Chapter 11 or click the *7 above.

Keyboard

Built-in The internal keyboard provides the embedded

numeric overlay keys, dedicated cursor control overlay keys, and Keys. The keyboard is compatible with the IBM Refer to Chapter 5, The Keyboard, for details.

enhanced keyboard.

Pointing Device

Built-in Touch Pad The integrated Touch Pad and control buttons in

the palm rest allow control of the on-screen pointer and support functions such as the scrolling of windows.

User’s Manual 1-7

Introduction

Ports

External monitor This port provides 15-pin, analog VGA port.This

port allows you to connect an external monitor to the computer.

Universal Serial Bus (USB 2.0)

The computer supports multiple Universal Serial Bus ports that comply with the USB 2.0 standard. The ports with the ( ) has a USB Sleep and

Charge function.

One of the USB ports has an eSATA (External Serial ATA) function.

■ Please note that it is not possible to confirm the operation of all

functions of all USB devices that are available. In view of this it may be noted that some functions associated with a specific device might not operate properly.

i.LINK™ (IEEE1394) This port allows high-speed data transfer to take

place between the computer and external devices such as digital video cameras.

Slots

ExpressCard™ The internal ExpressCard slot is a Universal slot.

This slot supports ExpressCard/54 and ExpressCard/34 modules.

Bridge media This slot lets you insert an SD™/SDHC™

memory card, miniSD™/microSD™ Card, Memory Stick xD-Picture Card™ and MultiMediaCard™. Refer to Chapter 9, Optional Devices.

(Duo™/PRO™/PRO Duo™),

User’s Manual 1-8

Multimedia

Introduction

Sound system The integrated sound system provides support

for the computer's internal speakers and microphone, also allowing an external microphone and headphones to be connected via the appropriate jacks.

Web Camera Web Camera is a device that allows you to

record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger. Camera Assistant Software will help you to add various video effects to your video or photograph.

Please refer to the Web Camera section in Chapter 4, Operating Basics.

TV antenna port Connect the antenna cable to this port to watch

or record TV programs on your computer. The dimensions and shape of the TV antenna

port vary for different regions.

HDMI out port HDMI out port can connect with Type A

connector HDMI cable. HDMI cable can send video and audio signals. In

addition to this, it can send and receive control signals.

By connecting a TV which supports HDMI Control to this port, the remote control for the connected TV can be used to operate some of the computer functions.

Refer to the REGZA Link (PC Control) section in C

Headphone, S/PDIF and Line out jack

This jack lets you connect digital speakers or a stereo headphone (16 ohm minimum). When you connect a digital speaker or headphones, the internal speaker is automatically disabled. This jack can be used also as S/PDIF jack and enables connection of optical digital correspondence apparatus.

Microphone and Line in jack

A 3.5mm mini microphone jack enables connection of a three-conductor mini jack for stereo microphone input, and connection of a stereo device for audio input.

User’s Manual 1-9

Introduction

TV Tuner TV Tuner enables watching and recording TV

programs. Some models are equipped with the TV Tuner.

FM Tuner Connecting the included FM Tuner antenna to

this jack enables reception of FM broadcasts.Some models are equipped with the FM tuner jack.

Infrared receiver window

This is a sensor window that receives signals from the remote controller which is provided with your computer.

Models which do not include a remote controller are not equipped with an infrared received so the computer cannot be operated with a remote controller.

Infrared transmitter cable port

Connect the Infrared transmitter cable to this port. Connecting the set top box or other external device to the computer using the infrared transmitter cable allows the external device to be operated using the computer and specialized remote control.

Full size remote controller

Some models are equipped with the Full size remote controller. Use this device to navigate when watching TV or playing CDs/DVDs.

Slim size remote controller

Use this device to navigate when playing CDs/DVDs.This device is stored within the ExpressCard slot.Some models are equipped with the Slim size remote controller.

■ Some models are included with a Full size remote controller or Slim

size remote controller.

User’s Manual 1-10

Introduction

Communications

Modem Some models are equipped with the integrated

modem. The integrated modem provides capability for data and fax communications that support the V.90 (V.92) standards and includes a modem jack for connection to the telephone line. Please note that both the V.90 and V.92 standards are only supported in the USA, Canada, United Kingdom, France, Germany and Australia - only the V.90 standard is supported in other regions. You should also be aware that the speed of data and fax transfer will depend on the analog telephone line conditions. The integrated model is only installed as a standard device in some markets.

LAN The computer has built-in support for Ethernet

LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T).

It is pre-installed as a standard device in some markets.

Bluetooth

Some computers in this series have Bluetooth wireless communication function which eliminates the need for cables between electronic devices such as computers and printers and mobile phones. When it is enabled, Bluetooth provides the wireless personal area network environment which is safe and trustworthy, that is quick and easy.

Wireless LAN Some computers in this series are equipped with

a Wireless LAN module that is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard.

■ The transmission speed over the wireless LAN and the distance over

which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. The Transmit Rate (at X Mbit/s) is the theoretical maximum speed under the IEEE802.11 (a/b/g/n) standards. The actual transmission speed will be lower than the theoretical maximum speed.

User’s Manual 1-11

Introduction

Legal Footnote (Wireless LAN)*7

For more information regarding Wireless LAN, please refer to the Legal

Footnotes section in Chapter 11 or click the *8 above.

Wireless communication switch

Security

Security lock slot Connects a security lock to anchor the computer

Special features

The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use.

Access each function using the following procedures. *1 To access the Power Options, click Start -> Control Panel -> System

and Maintenance -> Power Options.

USB Sleep and Charge function

Hot keys Hot keys are specific key combinations that let

Display automatic power off

HDD automatic power off

This switch turns the Wireless LAN and Bluetooth functions on and off. Please note that all models are provided with a Wireless communication switch and some models are equipped with both Wireless LAN and Bluetooth functionality.

to a desk or other large object.

This feature supplies USB bus power (DC5V) to the USB port even when the power of the computer is turned OFF. This can be specified in the HW Setup. It can only be used for ports that support the USB Sleep and Charge function (hereinafter called "compatible ports").

To run the HW Setup program, click Start -> All Programs -> TOSHIBA -> Utilities -> HWSetup.

you quickly change the system configuration directly from the keyboard without running a system program.

This feature automatically cuts off power to the computer's display panel when there is no keyboard input for a specified time, with power being restored the next time a key is pressed. This can be specified in the Power Options.

This feature automatically cuts off power to the hard disk drive when it is not accessed for a specified time, with power being restored when the hard disk drive is next accessed. This can be specified in the Power Options.

User’s Manual 1-12

Introduction

System automatic Sleep/Hibernation

Mode

This feature automatically shuts down the system into either Sleep Mode or Hibernation Mode when there is no input or hardware access for a specified time. This can be specified in the Power Options.

Keypad overlay A ten-key numeric keypad is integrated into the

keyboard. Please refer to the Keypad overlay section in Chapter 5, The Keyboard, for information on using this feature.

Power on password Two levels of password security, supervisor and

user, are available to prevent unauthorized access to your computer.

Instant security A specific hot key function automatically locks the

system providing data security.

Intelligent power supply

A microprocessor in the computer's intelligent power supply detects the battery's charge, automatically calculates the remaining battery capacity and protects electronic components from abnormal conditions such as a voltage overload from the AC adaptor. This can be specified in the Power Options.

Battery save mode

This feature lets you configure the computer in order to save battery power. This can be specified in the Power Options.

Low battery automatic

Hibernation Mode

When battery power is exhausted to the point that computer operation cannot be continued, the

system automatically enters Hibernation Mode and shuts itself down. This can be specified in the Power Options.

Heat dispersal

To protect against overheating, the processor has an internal temperature sensor so that, if the computer's internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. This can be specified in the Power Options.

If the processor's temperature reaches an unacceptably high level with either setting, the computer will automatically shuts down to prevent any damage - in this instance all unsaved data in memory will be lost.

User’s Manual 1-13

Hibernation Mode This feature lets you turn off the power to the

computer without exiting from your software. The contents of main memory are automatically saved to the hard disk drive so that when you next turn the power on again, you can continue working right where you left off. Refer to the

Turning off the power section in Chapter 3, Getting Started, for more details.

Sleep Mode If you have to interrupt your work, you can use

this feature to allow you to turn off power to the computer without exiting from your software. Data is maintained in the computer's main memory so that when you next turn on the power, you can continue working right where you left off.

TOSHIBA Value Added Package

This section describes the TOSHIBA Component features pre-installed on the computer.

Introduction

TOSHIBA Power Saver

TOSHIBA Button Support

TOSHIBA Zooming Utility

TOSHIBA PC Diagnostic Tool

TOSHIBA Password Utility

TOSHIBA Power Saver provides you with the features of more various power supply managements.

This utility controls the following computer panel functions.

The applications associated with each of the following panels can be assigned by the user.

■ Panels: Assign applications to the Mute,

Illumination On/Off, Camera, DOLBY

panels.

This utility allows you to enlarge or reduce the icon size on the Windows Desktop, or the zoom factor associated with specific supported applications.

The TOSHIBA PC Diagnostic Tool will display basic system configuration information and allow the functionality of some of the computer's builtin hardware devices to be tested.

The TOSHIBA Password utility allows you to set a password in order to restrict access to the computer.

User’s Manual 1-14

Introduction

TOSHIBA Flash Cards

The TOSHIBA Flash Cards provide a quick way to modify selected system functions and to launch applications.

■ Hot key function

■ TOSHIBA utility launcher function

HW Setup This utility allows you to customize your

hardware settings according to the way you work with the computer and the peripherals you use.

TOSHIBA Accessibility

The TOSHIBA Accessibility utility provides support to movement impaired users when they need to use the TOSHIBA Hot-key functions. In use, the utility allows you to make the FN key 'sticky', that is you can press it once, release it, and they press one of the 'F' keys in order to access its specific function. When set, the FN key will remain active until another key is pressed.

User’s Manual 1-15

Utilities and Applications

This section describes the pre-installed utilities that come with the computer and details how to start them. For further information on their operation, please refer to each utility's online manual, help files or README.TXT file.

Fingerprint Utility Some models of this computer series support a

Introduction

fingerprint utility, which is installed for the purpose of enrolling and recognizing fingerprints which can then be linked to a username and password in order to remove the need to input these details from the keyboard. Just by swiping an enrolled finger against the fingerprint sensor, the following functions will be enabled:

■ Logon to Windows and access a security

enabled homepage through Internet Explorer.

■ Files and folders can be encrypted/decrypted

and third party access to them is prevented.

■ Disable the password-protected screen-saver

when returning from a power-saving mode such as Sleep Mode.

■ Authentication of the User Password (and, if

applicable, the HDD(Hard Disk Drive) Password) when booting up the computer (Pre-OS Authentication).

■ Single-Swipe Sign-on feature

■ Fingerprint security cannot be used in models that do not have a

fingerprint module installed.

TOSHIBA Face Recognition

TOSHIBA HD Console

User’s Manual 1-16

TOSHIBA Face Recognition uses a face verification library to verify the face data of users when they log in to Windows. If the verification is successful, the user will be logged into Windows automatically. The user can thus avoid having to enter a password or the like, which makes the login process easier.

The TOSHIBA HD Console displays the usage for each core in the TOSHIBA Quad Core HD Processor and allows applications which use the TOSHIBA Quad Core HD Processor to be started. The TOSHIBA HD Console is displayed in the Windows Sidebar. TOSHIBA HD Console is equipped with some models.

Introduction

TOSHIBA Gesture Controller

Toshiba Graphical Video Library

Bluetooth Stack for Windows by Toshiba

TOSHIBA Gesture Controller is software which allows the computer's Web camera to be used with gestures in place of mouse and remote controller operations to control the TOSHIBA DVD PLAYER when watching or listening to video or music. To start this software, follow the steps and details below:1.To start the TOSHIBA Gesture Controller, click Gesture Interface Launch button in the TOSHIBA HD Console on the Windows Sidebar.2.The Gesture Interface Launch button display will change to Gesture Interface Running, the TOSHIBA Gesture Controller will start and the TOSHIBA Gesture Controller window will be displayed. TOSHIBA Gesture Controller software is equipped with some models. Please refer to the help file of software for details.

This software allows you to display a list of all the files and subfolders within a specified folder, index videos and play files. The Index Viewer can also be started in order to view the results of video indexing. Please refer to the help file of software for details. To start this software, click

Start -> All Programs -> Windows Media Center -> TOSHIBA -> Video Library. TOSHIBA

Graphical Video Library software is equipped with some models.

This software enables communication between the computer and external Bluetooth devices such as printers and mobile phones.

Bluetooth functions cannot be used in models that do not have a Bluetooth module installed.

TOSHIBA Assist TOSHIBA Assist is a graphical user interface that

provides access to specific tools, utilities and applications that make the use and configuration of the computer easier.

TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities that

improve the ease and control of communication devices and network connections, help in the identification of communication problems and allow the creation of profiles if you need to switch between different locations and communication networks. To access this utility, click Start -> All Programs -> TOSHIBA -> ConfigFree.

User’s Manual 1-17

Introduction

TOSHIBA Disc Creator

You can create CD's and DVD's in a number of formats including audio CD's that can be played on a standard CD player, and data CD's/DVD's which can store copies of the files and folders on your computer's hard disk drive. This software can be used on models with a DVD Super Multi drive.

To start this utility, click Start -> All Programs ->

TOSHIBA -> CD&DVD Applications -> Disc Creator.

TOSHIBA DVD-RAM Utility

This utility has the function of Physical Format and Write-Protect to DVD-RAM. This utility is contained the setup module of TOSHIBA Disc Creator. To start this utility, click Start -> All

Programs -> TOSHIBA -> CD&DVD Applications -> DVD-RAM Utility.

Ulead DVD MovieFactory for TOSHIBA

Ulead DVD MovieFactory for TOSHIBA allows users to instantly create DVD video or slideshow discs via a user-friendly wizard interface with specific task oriented features.

The Labelflash feature is also supported which allows text and images to be printed on the label surface of Labelflash compatible media without using a printer. Some models supports the Labelflash function.

Labelflash features cannot be used in models that do not have a DVD Super Multi drive with Labelflash.

In order to determine if the optical disc drive installed in your computer supports Labelflash follow the steps as detailed below:

1. Click Start -> All Programs -> DVD MovieFactory for TOSHIBA -> Ulead DVD MovieFactory for TOSHIBA Launcher to launch DVD MovieFactory.

2. Click Print Disc Label -> Label Printing. Ulead Label@Once is started.

3. Click the General tab.

4. Choose optical disc drive for Printer.

If the drive name is displayed in Step 4, your computer's optical disc drive supports Labelflash.

User’s Manual 1-18

Introduction

Windows Mobility Center

This section describes the Windows Mobility Center. Mobility Center is a utility for accessing several mobile PC settings quickly in one window. A default maximum of eight tiles are provided by the operating system, and the additional two tiles are added to your Mobility Center.

■ Lock Computer:

This can be used to lock your computer without turning it off. This has the same function as the Lock button at the bottom of the right pane in the start menu.

■ TOSHIBA Assist:

This can be used to open TOSHIBA Assist if it is already installed in your computer.

TOSHIBA DVD PLAYER

This software is provided for playback of DVD Video.It has an on-screen interface and functions. Click Start -> All Programs -> TOSHIBA DVD PLAYER.

Frame dropping, audio skipping or out of synch audio and video may occur during playback of some DVD Video titles. Make sure to connect the computer's AC adaptor when playing a DVD Video. Power-saving features may interfere with smooth playback.

CD/DVD Drive Acoustic Silencer

The CD/DVD Drive Acoustic Silencer utility allows you to configure the read speed at which the optical disc drive will operate. In use you can select either Normal Mode, which will operate the drive at its maximum speed for quick data access, or Quiet Mode, which operates the drive at single speed for audio CD playback and which can lessen the operational noise. This utility does not have any function when using DVD's.

User’s Manual 1-19

Optinal accessories

You are able to add a number of options and accessories in order to make your computer even more powerful and convenient to use. For reference, the following list details some of the items that are available from your reseller or TOSHIBA dealer:

Memory expansion 1,024MB or 2,048MB memory module

Battery Pack An additional battery pack can be purchased for

Universal AC Adaptor

USB FDD Kit The USB floppy diskette drive accommodates

Battery Charger The optional battery charger allows you to

Introduction

(DDR2-800) can easily be installed in the computer.

use as either a spare or replacement. Please refer to Chapter 6, Power for futher information.

If you frequently use your computer at more than one site, it may be convenient to purchase an additional AC adaptor to be kept at each site in order to remove the need to always carry the adaptor with you.

either a 1.44MB or 720KB floppy diskette through connection to one of the computer's USB ports. In use, please be aware that, while you cannot format 720KB floppy diskettes under Windows

Vista

, you are able to read and write to diskettes

that have already been formatted.

charge extra battery packs outside of having to use the computer.

User’s Manual 1-20

The Grand Tour

This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer.

Legal Footnote (Non-applicable Icons)*9

For more information regarding Non-applicable Icons, please refer to the

Legal Footnotes section in Chapter 11 or click the *9 above.

Please handle your computer carefully to avoid scratching or damaging the surface.

Front with the display closed

The following figure shows the computer’s front with its display panel in the closed position.

Chapter 2

WLAN LED

Infrared receiver

window

Figure 2-1 Front of the computer with display closed

User’s Manual 2-1

Wireless

communication

switch

The Grand Tour

Wireless communication switch

Slide this switch to the right to turn on Wireless LAN and Bluetooth functions. Slide it to the left to turn off the functions.

All models are provided with a Wireless communication switch although only some models are equipped with both Wireless LAN and Bluetooth functions.

■ Turn Wi -Fi® and Bluetooth functionalities off when near a person who

may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction of your medical device when using any Wi-Fi or Bluetooth functionality.

■ Always turn off Wi-Fi or Bluetooth functionality if the computer is near

automatic control equipment or appliances such as automatic doors or fire detectors. Radio waves can cause malfunction of such equipment, possibly resulting in serious injury.

■ Do not use the Wi-Fi or Bluetooth functionalities near a microwave

oven or in areas subject to radio interference or magnetic fields. Interference from a microwave oven or other source can disrupt Wi-Fi or Bluetooth operation.

Infrared receiver window

This is a sensor window that receives signals from the remote control which is provided with your computer.

Models which do not include a remote controller are not equipped with an infrared received so the computer cannot be operated with a remote controller.

User’s Manual 2-2

Left side

The following figure shows the computer's left side.

Bridge Media

Slot

i.LINK

(IEEE1394)

Headphones/

S/PDIF,

Line Out

The Grand Tour

Universal

Serial Bus

(USB 2.0) port

Microphone

/Line in

Figure 2-2 The left side of the computer

DVD Super

Multidrive

Optical disc drive The computer is configured with a DVD Super

Multi drive.

Universal Serial Bus (USB 2.0) ports

Two Universal Serial Bus ports, which comply with the USB 2.0 standard, are provided on the left hand side of the computer. The ports with the icon ( ) has USB Sleep and Charge function.

Keep foreign metal objects, such as screws, staples and paper clips, out of the USB connectors. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

Please note that it is not possible to confirm the operation of all functions of all USB devices that are available. In view of this it may be noted that some functions associated with a specific device might not operate properly.

Bridge media slot

This slot lets you insert an SD™/SDHC™ memory card, miniSD™/microSD™ Card,

Memory Stick® (Duo™/PRO™/PRO Duo™), xD-Picture Card™ and MultiMediaCard™. Refer to Chapter 9, Optional Devices.

Keep foreign metal objects, such as screws, staples and paper clips, out of the Bridge media slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

User’s Manual 2-3

The Grand Tour

Right side

Headphone, S/PDIF and Line out jack

A 3.5 mm mini headphone jack that lets you connect digital speakers or a stereo headphone (16 ohm minimum). When you connect a digital speaker or headphones, the internal speaker is automatically disabled.

This jack can be used also as S/PDIF jack and enables connection of optical digital correspondence apparatus.

Microphone and Line in jack

A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input, and connection of a stereo device for audio input.

i.LINK (IEEE1394) port

This port allows you to connect an external device, such as a digital video camera, to the computer for high-speed data transfer.

The following figure shows the computer’s right side.

USB

Infrared

transmitter

cable port

Figure 2-3 The right side of the computer

Card Slot

HDMIExpress

Security

Lock

Security lock slot A security cable can be attached to this slot and

then connected to a desk or other large object in order to deter theft of the computer.

Universal Serial Bus (USB 2.0) port

The Universal Serial Bus port, which complies with the USB 2.0 standard, is provided on the right side of the computer.

ExpressCard slot This slot allows you to install a single

ExpressCard device. Slim size remote controller is contained in the

ExpressCard slot. Some models are equipped with a Slim size remote controller.

User’s Manual 2-4

Back

The Grand Tour

Keep foreign metal objects, such as screws, staples and paper clips, out of the ExpressCard slot and PC Card slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

HDMI out port HDMI out port can connect with Type A

connector HDMI cable.One HDMI cable can send video and audio signals. In addition to this, it can send and receive control signals.

By connecting a TV which supports HDMI Control to this port, the remote control for the connected TV can be used to operate some of the computer functions.Refer to the REGZA Link section in Chapter 9, Optional Devices, for more details.

Infrared transmitter cable port

Connect the Infrared transmitter cable to this port.Connecting the set top box or other external device to the computer using the infrared transmitter cable allows the external device to be operated using the computer and specialized remote control.

The following figure shows the computer’s back.

eSATA/USB

combo port

DC in jack

Figure 2-4 The back of the computer

User’s Manual 2-5

External

monitor port

LAN jackUSB

TV antenna port

Modem Jack or

FM antenna port

or no port

The Grand Tour

TV antenna port Connect the antenna cable to this port to watch

TV programs on your computer or record them. The dimensions and shape of the TV antenna

port vary for different regions.

DC IN 19V jack The AC adaptor connects to this jack in order to

power the computer and charge its internal batteries. Please note that you should only use the model of AC adaptor supplied with the computer at the time of purchase - using the wrong AC adaptor can cause damage to the computer.

Cooling vents The cooling vents help keep the processor from

overheating.

Do not block the cooling vents. Keep foreign metal objects, such as screws, staples and paper clips, out of the cooling vents. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

Universal Serial Bus (USB 2.0) ports

(USB 2.0) portOne Universal Serial Bus port, which complies to the USB 2.0 standard, is provided on the left hand side of the computer. The ports with the icon ( ) has USB Sleep and Charge function.

eSATA/USB combo port

This Universal Serial Bus port, which complies to the USB 2.0 standard, is provided on the back of the computer. The ports with the icon ( ) has USB Sleep and Charge function. This port has eSATA (External Serial ATA) function.

External monitor port

This port allows you to connect an external monitor to the computer.

LAN jack This jack lets you connect to a LAN. The adaptor

has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). The LAN has two indicators. Refer to Chapter 4, Operating Basics, for details.

■ Do not connect any cable other than a LAN cable to the LAN jack. It

could cause damage or malfunction.

■ Do not connect the LAN cable to a power supply. It could cause

damage or malfunction.

User’s Manual 2-6

The Grand Tour

Link indicator (green)

LAN active indicator (yellow)

This indicator glows green when the computer is connected to a LAN and the LAN is functioning properly.

This indicator glows yellow when data is being exchanged between the computer and the LAN.

Modem jack The modem jack allows you use to attach a

modular cable in order to connect the internal modem directly to a telephone line.

Some models are equipped with a built-in modem.

■ Connection to any communication line other than an analog phone line

could cause a computer system failure.

■ Connect the built-in modem only to ordinary analog phone lines.

■ Never connect the built-in modem to a digital line (ISDN).

■ Never connect the built-in modem to the digital connector on a

public telephone or to a digital private branch exchange (PBX).

■ Never connect the built-in modem to a key telephone system for

residences or offics.

■ Avoid using your computer modem with the telephone cable connected

during an electrical storm. There may be a remote risk of electric shock from lightning.

FM tuner jack A FM tuner jack enables FM tuner antenna

connection. Some models are equipped with an FM tuner jack.

User’s Manual 2-7

Underside

The following figure shows the underside of the computer. You should ensure that the display is closed before the computer is turned over to avoid causing any damage.

Hard disk

drive

The Grand Tour

Memory

Battery

Subwoofer

Figure 2-5 The underside of the computer

Cooling Vent

Memory module slots

The memory module slots are located here. The memory module slots allow for the installation, replacement and removal of additional memory modules. Please refer to the Additional memory

module section in Chapter 9, Optional Devices

for more information.

Battery safety lock Slide this latch into its 'Unlock' position in order to

release the battery pack ready for removal.

Battery release latch Slide and hold this latch into its 'Unlock' position

in order to release the battery pack ready for removal.

For more detailed information on removing the battery pack please refer to Chapter 6, Power.

User’s Manual 2-8

The Grand Tour

Battery pack The battery pack provides power to the computer

when the AC adaptor is not connected. For more detailed information on the use and operation of the battery pack please refer to Chapter 6,

Power.

Speaker (subwoofer) The subwoofer will reproduce of the low

frequency sounds generated.

Cooling vents The computer's cooling vents help keep the

Front with the display open

This section shows the computer with the display panel open. In order to open the display, simply push the display latch on the front of the computer, lift the display panel up and position it at a comfortable viewing angle for you.

Wireless LAN antenna

(Not shown)

LCD Sensor (Not shown)

Stereo speaker

Front operation

(left)

panel

processor from overheating.

Web Camera LED Web Camera Wireless LAN antennas

(Not shown)

Microphone

Display Screen

Stereo speaker (right)

Bluetooth antenna (Not shown)

Touchpad

Finger Print Sensor

Touchpad button

Volume dial

System Indicators

Figure 2-6 The front of the Touch Pad model with the display open

Display hinge The display hinge allows the display panel to be

position at a variety of easy-to-view angles.

User’s Manual 2-9

The Grand Tour

Stereo speakers The speakers emit sound generated by your

software as well as audio alarms, such as low battery condition, generated by the system.

Keep foreign objects out of the speakers. Never allow metal objects, such as screws, staples and paper clips, to enter the computer or keyboard. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.

Display screen Please be aware that, when the computer is

operating on the AC adaptor, the image displayed on the internal screen will be somewhat brighter than when it operates on battery power. This difference in brightness levels is intended to save power when operating on batteries. For more information on the computer's display, please refer to the Display

Controller and Video modes section in Appendix

Front operation panel (nine panels)

Nine panels are available for use: CD/DVD, Play/Pause, Stop, Previous, Next,

Mute, Illumination On/Off, Camera and DOLBY. These panels allow you to manage Audio/Video,

run applications and access utilities. Refer to Chapter 8, AV functions for details.

Power button Press this button to turn the computer's power on

and off.

Touch Pad The Touch Pad mouse control device located in

the center of the palm rest is used to control the movement of the on-screen pointer. For more information, please refer to the Using the Touch

Pad section in Chapter 4, Operating Basics.

Touch Pad control buttons

The control buttons located below the Touch Pad allow you to select menu items or manipulate text and graphics as designated by the on-screen pointer.

Fingerprint Sensor This sensor enables you to enroll and recognize

a fingerprint.For detailed information on Fingerprint Sensor, refer to Chapter 4, Using the

Fingerprint Sensor. Some models are equipped

with an Fingerprint Sensor.

User’s Manual 2-10

The Grand Tour

System indicators These LED indicators allow you to monitor the

status of various computer functions and are described in more detail within the System

indicators section.

Web Camera Web Camera is a device that allows you to

Enables the transmission of video and use of video chat via the internet using specialized applications.

The effective pixel count for this web camera is

1.31 million (maximum photograph size: 1280x1024 pixels).

Please refer to the Web Camera section in Chapter 4, Operating Basics.

Web Camera LED

The Web Camera LED glows when the Web Camera is operating.

Please remove the protective plastic-film before using the Web Camera.

LCD Sensor switch This switch senses when the display panel is

either closed or opened and activates the Panel Power Off/On feature as appropriate. For example, when you close the display panel the computer enters Hibernation Mode and shuts itself down and then, when you next open the display, the computer will automatically start up and return you to the application you were previously working on.

You can specify within the Power Options. To access it, click Start -> Control Panel -> System and Maintenance -> Power Options.

Do not put any magnetic objects close to this switch as they may cause the computer to automatically enter Hibernation Mode and shut down even if the Panel Power Off feature is disabled.

User’s Manual 2-11

The Grand Tour

Volume control dial Use this dial to adjust the volume of the internal

stereo speakers and optional external stereo headphones (if connected).

Move the Volume control dial to the right to decrease the volume and to the left to increase the volume.

Microphone A built-in microphone allows you to import and

record sounds for your application - please refer to the Sound system section in Chapter 4,

Operating Basics for more information.

Bluetooth antenna Some computers in this series are equipped with

a Bluetooth antenna.

Wireless LAN antennas

System indicators

The LED system indicators for specific computer operations glow when those operations are in progress.

DC IN The DC IN indicator normally glows blue when

Power The Power indicator normally glows blue when

Battery The Battery indicator shows the condition of the

Some computers in this series are equipped with a Wireless LAN antennas.

Figure 2-7 System indicators

power is being correctly supplied from the AC power adaptor. However, If the output voltage from the adaptor is abnormal, or if the computer's power supply malfunctions, this indicator will flash amber.

the computer is turned on. However, if you turn the computer off into Sleep Mode, this indicator will flash amber - approximately one second on, two seconds off - both while the system is shutting down and while it remains turned off.

battery's charge - blue indicates the battery is fully charged, amber indicates the battery is charging, and flashing amber indicates a low battery condition. Please refer to Chapter 6,

Power for more information on this feature.

User’s Manual 2-12

Hard Disk Drive The Hard Disk Drive indicator glows blue

whenever the computer is accessing the built-in hard disk drive or the other drives.

Bridge media slot The Bridge media slot indicator glows blue

when the computer is accessing the Bridge media slot.

Keyboard indicators

The following figures show the positions of the CAPS LOCK indicator and the keypad overlay indicators which show the following conditions:

■ When the CAPS LOCK indicator glows, the keyboard will produce

capitals when any letter is typed.

■ When the Arrow Mode indicator glows, the keypad overlay allows you to

use cursor functions.

■ When the Numeric Mode indicator glows, the keypad overlay allows

you to enter numbers.

The Grand Tour

CAPS LOCK indicator

Figure 2-8 Keypad indicators

CAPS LOCK This indicator glows green when letter keys are

locked into their uppercase format.

User’s Manual 2-13

Arrow Mode When the Arrow Mode indicator lights green,

Numeric Mode When the Numeric Mode indicator lights green,

Optical disc drives

The computer is configured with a DVD Super Multi drive. A Serial ATA interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows.For further information on loading and unloading discs, please refer to the

Using TOSHIBA Face Recognition section in Chapter 4, Operating Basics.

Region codes for DVD drives and media

DVD Super Multi drives and their associated media are manufactured according to the specifications of six marketing regions. When you purchase DVD-Video, make sure it matches your drive, otherwise it will not play properly.

The Grand Tour

you can use the gray labeled keys on the keypad overlay as cursor keys. Please refer to the

Keypad overlay section in Chapter 5, The Keyboard for more information.

you can use the gray labeled keys on the keypad overlay for number entry. Please refer to the

Keypad overlay section in Chapter 5, The Keyboard for more information.

Code Region

1 Canada, United States

2 Japan, Europe, South Africa, Middle East

3 South East Asia, East Asia

4 Australia, New Zealand, Pacific Islands, Central

America, South America, Caribbean

5 Russia, Indian Subcontinent, Africa, North Korea,

Mongolia

6 China

Writable discs

This section describes the types of writable CD/DVD discs. Check the specifications of your drive to see the types of discs it can write. Use TOSHIBA Disc Creator to write compact discs. Please refer to Chapter 4,

Operating Basics for further information.

User’s Manual 2-14

CDs

■ CD-R discs can be written only once. The recorded data cannot be

erased or changed.

■ CD-RW discs including multi speed CD-RW discs, high-speed CD-RW

discs and ultra-speed CD-RW discs can be recorded more than once.

DVDs

■ DVD-R, DVD+R, DVD-R (Dual Layer) and DVD+R (Double Layer) discs

can be written only once. The recorded data cannot be erased or changed.

■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than

once.

Formats

The drive supports the following formats. DVD Super Multi driveThe drive supports the formats CD-ROM, DVD-ROM, DVD-Video, CD-DA, CD-Text, Photo CDTM (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2, CD-R, CD-RW, DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, DVD+RW and DVD-RAM.

Some types and formats of DVD-R (Dual Layer) and DVD+R (Double Layer) discs may be unreadable.

The Grand Tour

DVD Super-Multi ROM drive

The full-size DVD-ROM module allows you to record data to recordable CD's and DVD's as well as run either 12cm (4.72") CD's, and DVD's, and 8cm (3.15") CD's and DVD's without using an adaptor.

The speed is slower at the center of a disc and faster at the outer edge.

DVD read 8 speed (maximum) DVD-R write 8 speed (maximum) DVD-R DL write 6 speed (maximum) DVD-RW write 6 speed (maximum) DVD+R write 8 speed (maximum) DVD+R DL write 6 speed (maximum) DVD+RW write 8 speed (maximum) DVD-RAM write 5 speed (maximum) CD read 24 speed (maximum) CD-R write 24 speed (maximum) CD-RW write 24 speed (maximum,

Ultra-speed media)

User’s Manual 2-15

AC adaptor

The AC adaptor can automatically adjust to any voltage ranging from 90 to 260 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost any country/region. The adaptor converts AC power to DC power and reduces the voltage supplied to this computer.

To recharge the battery, simply connect the AC adaptor to a power source and to the computer. Please refer to Chapter 6, Power for further information.

The Grand Tour

Figure 2-9 The AC adaptor (2-pin plug)

Figure 2-10 The AC adaptor (3-pin plug)

■ Depending on the model in question, either a 2-pin or 3-pin

adaptor/power lead will be bundled with the computer.

■ Do not use a 3-pin to 2-pin conversion plug.

■ The supplied power cord conforms to safety rules and regulations in

the region the product is bought and should not be used outside of this region. In order to use the adaptor/computer in other regions, you should please buy a power cord that conforms to the safety rules and regulations in that particular region.

Always use the TOSHIBA AC adaptor that was included with your computer, or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor.

User’s Manual 2-16

Getting Started

This chapter provides basic information to start using your computer. It covers the following topics:

■ If the battery pack is not pre-installed in the computer that you

purchased, please install the battery pack before you start using the computer. Please refer to Chapter6-9, Replacing the battery pack for further information about installing the battery pack.

■ All users should be sure to read the section Starting up for the first time.

■ Be sure to read the enclosed Instruction Manual for Safety and Comfort

for information on the safe and proper use of this computer. It is intended to help you be more comfortable and productive while using a notebook computer. By following the recommendations in it you may reduce your chance of developing a painful or disabling injury to your hand, arms, shoulders or neck.

■ Connecting the AC adaptor

■ Opening the display

■ Turning on the power

■ Starting up for the first time

■ Turning off the power

■ Restarting the computer

■ System Recovery Options

■ Creating Optical Recovery Discs

■ Restoring the pre-installed software from the Recovery hard disk drive

■ Restoring the pre-installed software from your created Recovery Discs

Chapter 3

User’s Manual 3-1

■ Use a virus-check program and make sure it is updated regularly.

■ Never format storage media without checking its content - formatting

destroys all stored data.

■ It is a good idea to periodically back up the internal hard disk drive or

other main storage device to external media. General storage media is not durable or stable over long periods of time and under certain conditions may result in data loss.

■ Before you install a device or application, save any data in memory to

the hard disk drive or other storage media. Failure to do so may result in the loss of data.

Connecting the AC adaptor

Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power.

The AC adaptor can be connected to any power source supplying from 90 to 260 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power.

Getting Started

User’s Manual 3-2

Getting Started

■ Always use the TOSHIBA AC adaptor that was included with your

computer or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor.

■ Never plug the AC adaptor into a power source that does not

correspond to both the voltage and the frequency specified on the regulatory label of the unit. Failure to do so could result in a fire or electric shock, possibly resulting in serious injury.

■ Always use or purchase power cables that comply with the legal

voltage and frequency specifications and requirements in the country of use. Failure to do so could result in a fire or electric shock, possibly resulting in serious injury.

■ The supplied power cord conforms to safety rules and regulations in

the region the product is bought and should not be used outside this region. For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region.

■ Do not use a 3-pin to 2-pin conversion plug.

■ When you connect the AC adaptor to the computer, always follow the

steps in the exact order as described in the User’s Manual. Connecting the power cable to a live electrical outlet should be the last step otherwise the adaptor DC output plug could hold an electrical charge and cause an electrical shock or minor bodily injury when touched. As a general safety precaution, avoid touching any metal parts.

■ Never place your computer or AC adaptor on a wooden surface,

furniture, or any other surface that could be marred by exposure to heat since the computer base and AC adaptor's surface increase in temperature during normal use.

■ Always place your computer or AC adaptor on a flat and hard surface

that is resistant to heat damage.

Refer to the enclosed Instruction Manual for Safety and Comfort for detailed precautions and handling instructions.

User’s Manual 3-3

Getting Started

1. Connect the power cord to the AC adaptor.

Figure 3-1 Connecting the power cord to the AC adaptor (2-pin plug)

Figure 3-2 Connecting the power cord to the AC adaptor (3-pin plug)

Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model.

2. Connect the AC adaptor's DC output plug to the DC IN 19V jack on the back of the computer.

DC IN 19V Jack

Figure 3-3 Connecting the adaptor to the computer

3. Plug the power cord into a live wall outlet - the Battery and DC IN indicators on the front of the computer should glow.

User’s Manual 3-4

Opening the display

The display panel can be opened to a wide range of angles for optimal viewing.

While holding down the palm rest with one hand so that the main body of the computer is not raised, slowly lift the display panel - this will allow the angle of the display panel to be adjusted to provide optimum clarity.

Display panel

Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer.

Getting Started

Figure 3-4 Opening the display

User’s Manual 3-5

Getting Started

■ As the display panel cannot be opened until 180 degrees, please be

careful of the angle when flipping open the display panel.

■ Be careful not to open the display panel too far as this could put stress

on the display panel’s hinges and cause damage.

■ Do not press or push on the display panel.

■ Do not lift the computer by the display panel.

■ Do not close the display panel with pens or any other objects left in

between the display panel and the keyboard.

■ When opening or closing the display panel, place one hand on the

palm rest to hold the computer in place and use the other hand to slowly open or close the display panel (Do not use excessive force when opening or closing the display panel).

Turning on the power

This section describes how to turn on the power - the Power indicator will then indicate the status. Please refer to the Monitoring of power condition section in Chapter 6, Power for more information.

■ After you turn on the power for the first time, do not turn it off until you

have set up the operating system. Please refer to the section Starting

up for the first time for more information.

■ Volume cannot be adjusted during Windows Setup.

User’s Manual 3-6

1. Open the computer's display panel.

2. Press the computer's power button.

Power button

Figure 3-5 Turning on the power

Starting up for the first time

Getting Started

The Microsoft Windows Vista® Startup Screen will be the first screen displayed when you turn on the power. Follow the on-screen instructions on each screen in order to properly install the operating system.

When it is displayed, be sure to read the Software License Terms carefully.

Turning off the power

The power can be turned off in one of three modes, either Shut Down Mode, Hibernation Mode or Sleep Mode.

Shut Down Mode

When you turn off the power in Shut Down Mode no data will be saved and the computer will boot to the operating system's main screen the next time it is turned on.

1. If you have entered data, either save it to the hard disk drive or to other storage media.

2. Make sure all disk/disc activity has stopped before removing the CD/DVD or floppy diskette.

User’s Manual 3-7

■ Make sure the Hard Disk Drive indicator is off. If you turn off the power

while a disk (disc) is being accessed, you may lose data or damage the disk.

■ Never turn off the power while an application is running. Doing so could

cause loss of data.

■ Never turn off the power, disconnect an external storage device or

remove storage media during data read/write. Doing so can cause data loss.

3. Click Start.

4. Click the arrow button ( ) located in the power management buttons ( ) and select Shut Down from the menu.

5. Turn off any peripheral devices connected to your computer.

Do not turn the computer or peripheral devices back on immediately - wait a short period to avoid any potential damage.

Sleep Mode

If you have to interrupt your work, you are able to turn off the power without exiting from your software by placing the computer into Sleep Mode. In this mode data is maintained in the computer's main memory so that when you turn on the power again, you can continue working right where you left off.

Getting Started

When you have to turn off your computer aboard an aircraft or in places where electronic devices are regulated or controlled, always completely shut down the computer. This includes turning off any wireless communication switches or devices, and canceling settings that reactivate the computer automatically, such as a timer recording function. Failure to completely shut down the computer in this way could allow the operating system to reactivate and run pre-programmed tasks or preserve unsaved data, which could interfere with aviation or other systems, possibly causing serious injury.

■ Before entering Sleep Mode, be sure to save your data.

■ Do not install or remove a memory module while the computer is in

Sleep Mode. The computer or the memory module could be damaged.

■ Do not remove the battery pack while the computer is in Sleep Mode

(unless the computer is connected to an AC power source). Data in memory could be lost.

User’s Manual 3-8

Getting Started

■ When the AC adaptor is connected, the computer will go into Sleep Mode

according to the settings in the Power Options (to access it, Start -> Control Panel -> System and Maintenance -> Power Options).

■ To restore the operation of the computer from Sleep Mode, press and

hold the power button or any key on the keyboard for a short amount of time. Please note that keyboard keys can only be used if the Wake-up on Keyboard option is enabled within the HW Setup utility.

■ If the computer enters Sleep Mode while a network application is

active, the application might not be restored when the computer is next turned on and the system returns from Sleep Mode.

■ To prevent the computer from automatically entering Sleep Mode,

disable Sleep Mode within the Power Options (to access it, Start -> Control Panel -> System and Maintenance -> Power Options).

■ To use the Hybrid Sleep function, configure it in the Power Options.

Benefits of Sleep Mode

The Sleep Mode feature provides the following benefits:

■ Restores the previous working environment more rapidly than does the

Hibernation Mode feature.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the time period set by the System Sleep Mode feature.

■ Allows the use of the panel power off feature.

Executing Sleep Mode

You can also enable Sleep Mode by pressing FN + F3 - please refer to Chapter 5, The Keyboard, for further details.

You can enter Sleep Mode in one of four ways:

■ Click Start then click the power button ( ) located in the power

management buttons ( ). Please note that this feature must be enabled within the Power Options

(to access it, click Start -> Control Panel -> System and Maintenance

-> Power Options).

■ Click Start then click the arrow button ( ) and select Sleep from the

menu.

■ Close the display panel. Please note that this feature must be enabled

within the Power Options (to access it, click Start -> Control Panel -> System and Maintenance -> Power Options).

■ Press the power button. Please note that this feature must be enabled

within the Power Options (to access it, click Start -> Control Panel -> System and Maintenance -> Power Options).

User’s Manual 3-9

When you turn the power back on, you can continue where you left when you shut down the computer.

■ When the computer is in Sleep Mode, the Power indicator will blink

amber.

■ If you are operating the computer on battery power, you can lengthen

the overall operating time by turning it off into Hibernation Mode - Sleep Mode will consume more power while the computer is off.

Sleep Mode limitations

Sleep Mode will not function under the following conditions:

■ Power is turned back on immediately after shutting down.

■ Memory circuits are exposed to static electricity or electrical noise.

Hibernation Mode

The Hibernation Mode feature saves the contents of memory to the hard disk drive when the computer is turned off so that, the next time it is turned on, the previous state is restored. Please note that the Hibernation Mode feature does not save the status of any peripheral devices connected to the computer.

■ Save your data. While entering Hibernation Mode, the computer saves

the contents of memory to the hard disk drive. However, for safety sake, it is best to save your data manually.

■ Data will be lost if you remove the battery or disconnect the AC adaptor

before the save is completed. Wait for the Hard Disk Drive indicator to go out.

■ Do not install or remove a memory module while the computer is in

Hibernation Mode. Data will be lost.

Getting Started

Benefits of Hibernation Mode

The Hibernation Mode feature provides the following benefits:

■ Saves data to the hard disk drive when the computer automatically

shuts down because of a low battery condition.

■ You can return to your previous working environment immediately when

you turn on the computer.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the time period set by the System Hibernate feature.

■ Allows the use of the panel power off feature.

Starting Hibernation Mode

You can also enable Hibernation Mode by pressing FN + F4 - please refer to Chapter 5, The Keyboard, for further details.

User’s Manual 3-10

Getting Started

To enter Hibernation Mode, follow the steps below.

1. Click Start.

2. Click the arrow button ( ) in the power management buttons

( ) and select Hibernate from the menu.

Automatic Hibernation Mode

The computer can be configured to enter Hibernation Mode automatically when you press the power button or close the lid. In order to define these settings, you can follow the steps as described below:

1. Click Start and click the Control Panel.

2. Click System and Maintenance and click Power Options.

3. Click Choose what the power button does or Choose what closing the lid does.

4. Enable the desired Hibernation Mode settings for When I press the power button and When I close the lid.

5. Click the Save changes button.

Data save in Hibernation Mode

When you turn off the power in Hibernation Mode, the computer will take a moment to save the current data in memory to the hard disk drive. During this time, the Hard Disk Drive indicator will glow.

After you turn off the computer, and the content of memory has been saved to the hard disk drive, turn off the power to any peripheral devices.

Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.

Restarting the computer

Certain conditions require that you reset the computer, for example if:

■ You change certain computer settings.

■ An error occurs and the computer does not respond to your keyboard

commands.

If you need to restart the computer, there are three ways this can be achieved:

■ Click Start then click the arrow button ( ) in the power management

buttons ( ) and select Restart from the menu.

■ Press CTRL, ALT and DEL simultaneously (once) to display the menu

window, then select Restart from the Shut down options.

■ Press the power button and hold it down for five seconds. Once the

computer has turned itself off, wait between ten and fifteen seconds before turning the power on again by pressing the power button.

User’s Manual 3-11

System Recovery Options

About 1.5GB hidden partition is allocated on the hard disk drive for the System Recovery Options.

This partition stores files which can be used to repair the system in the event of a problem.

The System Recovery Options feature will be unusable if this partition is deleted.

System Recovery Options

The System Recovery Options feature is installed on the hard disk when shipped from the factory. The System Recovery Options menu includes tools to repair startup problems, run diagnostics or restore the system.

See the Windows Help and Support content for more information about Startup Repair.

The System Recovery Options can also be run manually to repair problems.

The procedure is as follows. Follow the instructions shown on the on-screen menu.

1. Turn off the computer.

2. While holding the F8 key, turn on the computer.

3. The Advanced Boot Options menu will be displayed. Use the arrow keys to select Repair Your Computer and press ENTER.

4. Follow the on-screen instructions.

The Windows Vista Windows Vista

CompletePC Backup feature can be used on

Business Edition and Ultimate Edition.

Getting Started

System Recovery

This section describes the creation of Recovery Discs and their use.

User’s Manual 3-12

Creating Optical Recovery Discs

This section describes how to create Recovery Discs.

■ Be sure to connect the AC adaptor when you create Recovery Discs.

■ Be sure to close all other software programs except the Recovery Disc

Creator.

■ Do not run software such as screen savers which can put a heavy load

on the CPU.

■ Operate the computer at full power.

■ Do not use power-saving features.

■ Do not write to the disc when the virus check software is running. Wait

for it to finish, then disable virus detection programs including any software that checks files automatically in the background.

■ Do not use utilities, including those intended to enhance hard disk drive

access speed. They may cause unstable operation and damage data.

■ Do not shut down/log off or Sleep/Hibernate while writing or rewriting

the disc.

■ Set the computer on a level surface and avoid places subjected to

vibrations such as airplanes, trains, or cars.

■ Do not use on unstable tables or other any other unstable surfaces.

A recovery image of the software on your computer is stored on the hard disk drive, and can be copied to DVD media by using the following steps:

1. Select either blank DVD media.

2. The application will allow you to choose from a variety of different media onto which the recovery image can be copied including DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL and DVD+RW.

Getting Started

Please note that some of the above media may not be compatible with the optical disc drive installed into your computer. You should therefore verify the optical disc drive supports the blank media you have chosen before proceeding.

3. Turn on your computer and allow it to load the Windows Vista® operating system from the hard disk drive as normal.

4. Insert the first blank media into the optical disc drive tray.

5. Double click the Recovery Disc Creator icon on the Windows Vista

desktop, or select the application from Start Menu.

6. After Recovery Disc Creator starts, select the type of media and the title you wish to copy, and then click the Create button.

If your optical disc drive can only write to CDs, select 'CD' as the 'Disc Set' within the Recovery Disc Creator application.Otherwise, if your optical disc drive can write both CDs and DVDs, select the type of media you want to create.

User’s Manual 3-13

Getting Started

Restoring the pre-installed software from the Recovery hard disk drive

A portion of the total hard disk drive space is configured as a hidden recovery partition. This partition stores files which can be used to restore pre-installed software in the event of a problem.

If you subsequently set up your hard disk drive again, do not change, delete or add partitions in a manner other than specified in the manual, otherwise you may find that space for the required software is not available.

In addition, if you use a third-party partitioning program to reconfigure the partitions on your hard disk drive, you may find that it becomes impossible to setup your computer.

When the sound mute feature has been activated by pressing the Mute panel (Fn+ESC), be sure to disable this to allow sounds to be heard before starting the restore process. Please refer to Chapter 5, The Keyboard, for further details.

You can not use System Recovery Options if restoring the pre-installed software without System Recovery Options.

When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost.

1. Turn off your computer.

2. While holding down 0 (zero) key on the keyboard, turn on your computer.

3. A menu will be displayed from which you should follow the on-screen instructions.

Restoring the pre-installed software from your created Recovery Discs

If the pre-installed files are damaged, you are able to either use the Recovery Discs you have created or the hard disk drive recovery process to restore the computer to the state it was in when you originally received it. To perform this restoration, follow the steps below:

When the sound mute feature has been activated by pressing the FN + ESC key, be sure to disable this to allow sounds to be heard before starting

the restore process. Please refer to Chapter 5,The Keyboard, for further details.

You can not use System Recovery Options if restoring the pre-installed software without System Recovery Options.

When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost.

User’s Manual 3-14

Getting Started

1. Load the Recovery Discs into the optical disc drive and turn off the computer's power.

2. While holding down F12 key on the keyboard, turn on your computer when the Qosmio logo screen appears, release the F12 key.

For 2HDD Model, If HDD1 is first, go to step 3. If HDD1 is not first, do as follows:

■ Select Enter Setup.

■ Press the F9 key to set to default settings, and select the Yes.

■ When the "In Touch with Tomorrow TOSHIBA" prompt appears,

press the F12 key to display the Boot menu. Continue with step 3.

3. Use the up and down cursors key to select the CD-ROM icon from the menu. Please refer to the Boot Priority section in Chapter 7, HW Setup for further information.

4. A menu will be displayed from which you should follow the on-screen instructions.

When removing pre-installed drivers / utilities or when installing, you can setup the respective drivers / utilities from the following folder. C:\TOSAPINS\***

User’s Manual 3-15

Operating Basics

This chapter describes the basic operations of your computer, highlights the precautions that should be taken when using it.

Using the Touch Pad

To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.

Chapter 4

TouchPad

Touchpad Control buttons

Figure 4-1 Touch Pad and Touch Pad control buttons

The two buttons below the Touch Pad are used like the buttons on a standard mouse - press the left button to select a menu item or to manipulate text or graphics designated by the pointer, and press the right button to display a menu or other function depending on the software you are using.

User’s Manual 4-1

You can also tap the Touch Pad to perform functions similar to those of the left button on a standard mouse.

AV Controller

The following functions are available in this computer for operating the Media Center.

This section describes an overview of each function. Please refer to Chapter 8, AV functions for more information.

■ Front operation panel

■ Remote Controller

Front operation panel

The Front operation panel is located above the keyboard. AV related functions, such as CD/DVD, Play/Pause, Stop, Previous, Next,

Mute, Illumination On/Off, Camera and DOLBY are available.

Operating Basics

Click: Tap on ce Double-click: Tap twice Drag and drop: Tap to select the item(s) you want to move, leave your

finger on the Touch Pad after the second tap and then move the item(s) to their new destination.

Remote controller

Some models are provided with a remote controller. It can operate AV related functions.

Using the Fingerprint Sensor

Sone models has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. By enrolling the ID and password onto the fingerprint authentication feature, it is no longer necessary to input the password from the keyboard. Fingerprint feature enables you to:

■ Logon to Windows and access a security enabled homepage through

Internet Explorer.

■ Files and folders can be encrypted/decrypted and third party access to

them prevented.

■ Disable the password-protected screen-saver when returning from a

power-saving mode such as Sleep Mode.

■ Authentication of the User Password (and, if applicable, the HDD (Hard

Disk Drive) Password) when booting up the computer (Pre-OS Authentication).

■ Single-Swipe Sign On feature

User’s Manual 4-2

Fingerprint cannot be used in models that do not have a fingerprint module installed.

How to Swipe your Finger

Using the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures:

Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swipe finger levelly towards you until the sensor surface becomes visible. In performing this process, you should also take care to ensure that the center of your fingerprint is on the sensor.

The following illustrations show the recommended way to swipe your finger over the fingerprint sensor.

Sensor

Figure 4-2 Swipe the finger

Operating Basics

Sensor

■ Avoid swiping with your finger stiff or pressed too hard onto the sensor,

and take care to ensure that the center of the fingerprint is touching the sensor before swiping. Either of these conditions may cause fingerprint reading to fail.

■ Check the center of the fingerprint whorl before swiping and then

ensure this is swiped along the center line of the sensor.

■ There is a possibility of authentication failures if the finger is swiped too

quickly or too slowly - follow any on-screen instructions to adjust the speed used during the swipe process.

Points to note about the Fingerprint Sensor

Please be aware of the following considerations when using the fingerprint sensor. A failure to follow these guidelines might result in damage to the sensor, sensor failure, fingerprint recognition problems or a lower fingerprint recognition success rate.

■ Do not scratch or poke the sensor with your nails or any hard or sharp

objects.

■ Do not press the sensor strongly.

■ Do not touch the sensor with a wet finger or any wet objects - keep the

sensor surface dry and free from water vapor.

User’s Manual 4-3

Operating Basics

■ Do not touch the sensor with a soiled or dirty finger as minute foreign

particles of dust and dirt may scratch it.

■ Do not paste stickers or write on the sensor.

■ Do not touch the sensor with a finger or any other object which may

have a build-up of static electricity on it.

Observe the following before you place your finger on the sensor whether for fingerprint enrollment/registration or recognition.

■ Wash and dry your hands thoroughly.

■ Remove static electricity from your fingers by touching any metal

surface. Static electricity is a common cause of sensor failures, especially when the weather is dry.

■ Clean the sensor with a lint-free cloth - do not use detergent or any

other chemicals to clean the sensor.

■ Avoid the following finger conditions for enrollment or recognition as

they may result in fingerprint enrollment errors or a drop in the fingerprint recognition success rate

■ Soaked or swollen finger, for example as may occur after taking a

bath.

■ Injured finger

■ Wet finger

■ Soiled or oily finger

■ Extremely dry skin condition on finger

Observe the following to improve the fingerprint recognition success rate.

■ Enroll two or more fingers.

■ Enroll additional fingers if a recognition failure often occurs when using

already enrolled fingers.

■ Check the condition of your finger - any conditions which have changed

since enrollment, such as injury, rough skin, and extremely dry, wet, soiled, dirty, oily, soaked or swollen fingers, may lower the recognition success rate. Also if the fingerprint is worn down or the finger becomes thinner or fatter, the recognition success rate may be lowered.

■ As the fingerprint for each finger is different and unique you should

ensure that only the registered or enrolled fingerprint or fingerprints are used for identification.

■ Check the position and speed at which you swipe your finger across the

sensor - please refer to the preceding drawing.

■ The fingerprint sensor compares and analyzes the unique

characteristics in a fingerprint. However, there may be instances where certain users are unable to register their fingerprints due to insufficient unique characteristics in their fingerprints.

■ The recognition success rate may differ from user to user.

User’s Manual 4-4

Setup Procedure

Please use the following procedure when first using fingerprint authentication.

Fingerprint Registration

You should initially enroll the required authentication data using the Fingerprint Enrollment Wizard.

■ In use, the fingerprint authentication system will use the same

username and password as defined within the Windows operating system. If no Windows password has been configured, you must do this before starting the fingerprint registration process.

■ This sensor has the memory space for at least twenty-one fingerprint

patterns. You might be able to register more fingerprint patterns depending on the sensor memory usage.

1. To run this program, click Start -> All Programs -> TrueSuite Access Manager -> TrueSuite Access Manager.

You are also able to start the Fingerprint Enrollment Wizard by using the following methods.

■ Right-click the TrueSuite Access Manager icon in the Taskbar and

choose Open.

2. The Verif y screen will be displayed, enter the Windows logon password and click the Next button.

3. On the User's Fingers screen click the box above the finger you wish to register.

If any of the previously enrolled fingerprints is selected again, the latest information will be enrolled and any previous information over-written.

4. The Fingerprint Enrollment screen will be displayed and the tutorial will begin. First click "Replay video" and confirm the proper movement for the finger you wish to register. Then confirm the message displayed on this screen and ensure that there is a check mark in the Run Interactive Tutorial box. Once this has been done, click Next.

5. At the Scanning Practice screen, you are able to practice swiping (three times) your finger to ensure you use the correct method. Click "Try again" to if you wish to practice again. You have finished practicing, click Next button.

6. Register your fingerprint on the Fingerprint Image Capture screen.Let the computer read the finger to be registered 3 times. An image of your fingerprint will be shown on the screen each time the fingerprint is successfully read.

Once the fingerprint is successfully read for the third time, the message Successfully combined will be displayed beneath the fingerprint images and will close the window automatically.

7. When the Store To Sensor screen is displayed, check Store fingerprint to Sensor. Click Finish to complete fingerprint registration.

Operating Basics

User’s Manual 4-5

Operating Basics

It is strongly recommended that you register 2 or more fingerprints. Repeat the procedure from step 3 to register another fingerprint.

How to Delete the Fingerprint Data

Saved fingerprint data is stored in special non-volatile memory inside the fingerprint sensor. Therefore, if you give the computer to someone else, or dispose of it in any way, the following process is recommended to delete your fingerprint information:

1. To run this program, click Start -> All Programs -> TrueSuite Access Manager -> TrueSuite Access Manager.

2. The Verify screen will be displayed. Swipe your registered finger to User’s Fingers.

3. The User's Fingers screen is displayed.

■ To delete all registered fingerprints

1. Click Delete All Fingerprints.

2. The user selection screen will be displayed, select which user's

fingerprint data to delete and click Ok.

■ Selecting "Delete current user's fingerprints" will delete the

fingerprint data for the currently logged in user.

■ Selecting "Delete all users' fingerprints" will delete the fingerprint

data for all users, however this item can only be selected if the currently logged in user has administrator privileges.

3. "Are you sure you want to delete this fingerprint?" will be displayed

on the screen, click Yes button.

■ To delete individual fingerprints.

1. Click the fingerprint mark above the registered finger.

2. "Are you sure you want to delete this fingerprint?" will be displayed

on the screen, click Yes button.

In use, please be aware of the following limitations of the fingerprint sensor:

■ A warning message will be displayed when recognition is abnormal or

recognition is not successful within a fixed duration.

■ The fingerprint sensor compares and analyzes the unique

characteristics in a fingerprint. However, there may be instances where certain users are unable to register their fingerprints due to insufficient unique characteristics in their fingerprints.

■ The recognition success rate may differ from user to user.

■ Toshiba does not guarantee that this fingerprint recognition technology

will be error-free.

■ Toshiba does not guarantee that the fingerprint sensor will recognize

the enrolled user or accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of this fingerprint recognition software or utility.

User’s Manual 4-6

Points to note about the Fingerprint Utility software

You are able to backup saved fingerprint data and information within the PasswordBank by using the Import or Export User Data facility under the fingerprint management software. However, please be aware that any encrypted files cannot be backup within FileSafe using this function - in these instances it is recommended that you backup these files to external media using standard file copy processes.

The Encrypting File System (EFS) is a Windows Vista® feature. If a file is encrypted using EFS, it cannot be encrypted further using the

fingerprint authentication function.

Windows Logon via Fingerprint Authentication

If required, you are also able to use fingerprint authentication in place of the usual Windows logon process using your username and password.This method is especially useful where there are many users using the same computer as it removes the need for actual user selection when the system is started.

Fingerprint Authentication Procedure

1. Start up the computer.

2. At the Windows Welcome screen, choose any of the enrolled fingers and swipe the fingerprint on the sensor - if the authentication process is successful, the user will automatically be logged in to Windows.

Operating Basics

f the fingerprint authentication process fails you will need to log into Windows using the appropriate username and password. In addition, you should use this manual login process if fingerprint authentication fails for three consecutive tries - a warning message will be displayed when authentication is not normal or is not successful within a fixed duration.

Fingerprint Pre-OS Authentication

General

The fingerprint authentication system can be used to replace the keyboard based password authentication system that is used when the computer is turned on.

If you do not want to use the fingerprint authentication system for password authentication while booting up the computer, instead you prefer using the keyboard entry method, simply press the BACK SPACE key when the Fingerprint Pre-OS Authentication screen is displayed.

Using this process will switch the password input screen across to the keyboard based entry screen.

User’s Manual 4-7

Operating Basics

■ You must ensure that you use the TOSHIBA Password Utility to

register a User Password before using the Fingerprint Pre-OS Authentication and its extended function to allow fingerprints to be used to access the computer when it is turned on.

■ If the fingerprint authentication process fails five times, a preset time

limit is exceeded, or you press the BACK SPACE key, [Password =] will be displayed on the screen and you will have to enter either the User Password or Supervisor Password manually in order to start the computer.

■ When swiping your finger, please ensure that you do it slowly and at a

constant speed. If you find that this does not improve the authentication rate, you should try to adjust the speed at which the finger is swiped.

■ If there are any changes in the environment or settings related to

authorization, you will be required to provide authorization information such as a User Password (and, if applicable, the HDD(Hard Disk Drive) password).

How to Enable Fingerprint Pre-OS Authentication Settings

It is necessary to first enroll your fingerprint with the Fingerprint Application prior to enabling and configuring the Fingerprint Pre-OS Authentication System. You should check that your fingerprint is enrolled before configuring the settings (please refer to the Manual for Fingerprint

Registration/Enrollment for further instructions).

1. To run this program, click Start -> All Programs -> TrueSuite Access Manager -> TrueSuite Access Manager with Admin Privileges.

2. UserAccountControl screen is displayed, click the Allow button.This setting can only be changed if the currently logged in user has administrator privileges.

3. Swipe a registered finger on the fingerprint sensor.

4. Click the Setting menu at the TrueSuiteAccessManager screen.

5. Administrator Setting screen is displayed, check the "Enable Pre-OS Fingerprint Authentication" check box and then click OK.

6. Click the Exit button at the TrueSuiteAccessManager screen.

Fingerprint Single-Swipe Sign-on Feature

General

This is a feature that allows the user to complete the authentication for both the User/BIOS Password and logging onto Windows using only one fingerprint authentication when booting up. It is necessary to register the User/BIOS Password and Windows Logon Password before using the Fingerprint Power-on Security and this Fingerprint Single Sign-on Feature. Please use the TOSHIBA Password Utility to register your User/BIOS Password. If Windows Logon is not the default for your system, see Manual to register your Windows Logon Password.

User’s Manual 4-8

Operating Basics

Only one fingerprint authentication is required to replace the User/BIOS Password and the Windows Logon Password.

How to Enable Fingerprint Single-Swipe Sign-on Feature

It is necessary to first enroll your fingerprint with the TrueSuite Access Manager prior to enabling and configuring the Fingerprint Single Sign-on feature. You should check that your fingerprint is enrolled before configuring the settings (please refer to the Manual for Fingerprint

Registration/Enrollment for further instructions).

1. To run this program, click Start -> All Programs -> TrueSuite Access Manager -> TrueSuite Access Manager with Admin Privileges.

2. UserAccountControl screen is displayed, click the Allow button. This setting can only be changed if the currently logged in user has administrator privileges.

3. Swipe a registered finger on the fingerprint sensor.

4. Click the Settings at the TrueSuiteAccessManager screen.

5. Administrator Settings screen is displayed, check the "Enable Pre-OS Fingerprint Authentication" and "Enable Single Sign-On Fingerprint Authentication" check box and then click OK.

6. Click the Exit button at the TrueSuiteAccessManager screen.

Fingerprint utility limitations

TOSHIBA does not guarantee that the fingerprint utility technology will be completely secure or error-free, or that it will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software.

■ The fingerprint sensor compares and analyzes the unique

characteristics in a fingerprint. However, there may be instances where certain users are unable to register their fingerprints due to insufficient unique characteristics in their fingerprints.

■ The recognition success rate may differ from user to user.

Web Camera

Some models are equipped with a Web Camera. Web Camera is a device that allows you to record video or take

photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger. Camera Assistant Software will help you to add various video effects to your video or photograph.

Enables the transmission of video and use of video chat via the internet using specialized applications.

The effective pixel count for this web camera is 1.31 million (maximum photograph size: 1280x1024 pixels).

Please refer to the Camera Assistant Software Online Help for details.

User’s Manual 4-9

Operating Basics

Microphone

Web Camera

Web Camera LED

Figure 4-3 Web Camera

■ Please unstick the protective plastic-film before using the Web

Camera.

■ Do not point the web camera directly at the sun.

■ Do not touch or press strongly on the web camera lens. Doing so may

reduce image quality. Use an eyeglass cleaner (cleaner cloth) or other soft cloth to clean the lens if it becomes dirty.

■ Setting the [Size] to more than "800x600" will cause a larger amount of

data to be written to the hard disk drive and may interfere with smooth recording.

User’s Manual 4-10

Using TOSHIBA Face Recognition

This feature uses a face verification library to verify the face data of users when they log in Windows. The user can thus avoid having to enter a password or the like, which makes the login process easier.

■ TOSHIBA Face Recognition does not guarantee the correct

identification of a user. Changes to the likeness of a registrant, such as hairstyle changes, wearing a cap, or wearing glasses may affect the recognition rates when such changes occur after the registrant had registered.

■ TOSHIBA Face Recognition may incorrectly recognize faces that are

similar to a registrant.

■ For high security purposes, TOSHIBA Face Recognition is not a

suitable substitute for Windows passwords. When security is a high priority, use your established Windows passwords to log in.

■ Bright background light and/or shadows may prevent a registrant from

being recognized correctly. In that case, log in using your Windows password. If recognition of a registrant fails repeatedly, refer to your computer documentation to learn ways to improve recognition performance.

■ TOSHIBA Face Recognition records face data in a log when face

recognition fails. When transferring ownership or disposing of your computer, please uninstall the application or delete all the logs created by the application. For details on how to do this, see help file.

Operating Basics

Disclaimer

Toshiba does not guarantee that the face recognition utility technology will be completely secure or error-free. Toshiba does not guarantee that the face recognition utility will accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of the face recognition software or utility.

TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS, PROFITS, PROGRAMS DATA, NETWORK SYSTEMS OR REMOVABLE STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY THEREOF.

User’s Manual 4-11

How to register the Face Recognition Data

Take a picture for facial verification purposes, and register the data needed when you log in. To register the data needed when you log in, follow the steps as described below:

1. To launch this utility, click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA Face Recognition.

■ The Registration screen is displayed for a logged-in user whose face

has not been registered.

■ The Management screen is displayed for a logged-in user whose face

has already been registered.

2. Click the Register face button in the Management screen. The Registration screen is displayed.

■ If you wish to practice, click on the Next button in the Registration

screen.

■ If you do not wish to practice, click on the Skip button in the

Registration screen.

3. Click the Next button to start the guide.

4. First, take a picture while moving your neck slightly to the left and right.

5. Now take a picture while moving your neck down and up. Or click the Back button to practice the guide once more.

6. Click the Next button to start image-capturing process. Adjust the position of your face so that it fits within the face-shaped

frame.

7. Once your face has been positioned properly, the recording will commence.

Start moving your neck very slightly to the left and right, and then move your neck down and up.

8. Registration will end after you have repeatedly moved your neck left, right, down and up.

When the register succeeds, below message will be displayed on the screen: " Registration successful. Now we'll do the verification test. Click the Next button."

Click the Next button to perform the verification test.

9. Perform the verification test. Face the screen as you do when you register.

Operating Basics

■ If verification fails, click the Back button and re-register. Please refer to

step 8 from step 6.

10. If verification is successful, click the Next button and register an account.

11. Register the account. Fill in the account registration fields. Fill in the all fields.

User’s Manual 4-12

12. The Management screen is displayed. The registered account name will be displayed. Clicking on it will cause

the captured image of your face to be displayed on the left.

How to Delete the Face Recognition Data

Delete image data, account information, and personal record data created during registration. To delete the Face Recognition Data, follow the steps as described below:

1. To launch this utility, click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA Face Recognition.

The Management screen is displayed.

2. Select a user which is deleted in the Management screen.

3. Click the Delete button. "You are about to delete the user data. Would you like to continue?" will be displayed on the screen.

■ If you do not want the data to be deleted, click the No button and

you will then be returned to the Management screen.

■ Clicking on the Yes button will remove the selected user from the

Management screen.

How to launch the help file

For further information on this utility, please refer to the help file.

1. To launch the help file, click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA Face Recognition Help.

Operating Basics

Windows Logon via TOSHIBA Face Recognition

This section explains how to login to Windows with TOSHIBA Face Recognition. Two authentication modes are provided.

■ AUTO Mode Login screen: If the face authentication tile is selected by

default, you can log in without using the keyboard or mouse.

■ 1:1 Mode Login screen: This mode is essentially the same as AUTO

mode, but the Select Account screen will appear before the Display Captured Image screen, and you will need to select the user account to be authenticated in order to start the authentication process.

AUTO Mode Login screen

1. Turn on the computer.

2. The Select Tiles screen will be displayed.

3. Select Start face recognition ( ).

4. "Please turn your face to the camera" will be displayed.

5. Verification will be performed. If the authentication is successful, the image data taken in step 4 will be faded in and placed over one another.

■ If an error occurs during authentication, you will be returned to the

Select Tiles screen.

User’s Manual 4-13

6. Windows Welcome screen will be displayed, and will be logged in automatically to Windows.

1:1 Mode Login screen

1. Turn on the computer.

2. The Select Tiles screen will be displayed.

3. Select Start face recognition ( ).

4. The Select Account screen will be displayed.

5. Select the account, and click the Arrow button.

6. "Please turn your face to the camera" will be displayed.

7. Verification will be performed. If the authentication is successful, the image data taken in step 6 will be faded in and placed over one another.

■ If an error occurs during authentication, you will be returned to the

Select Tiles screen.

8. Windows Welcome screen will be displayed, and will be logged in automatically to Windows.

■ If authentication was successful, but an authentication error

subsequently occurred during the login to Windows, you will be asked to provide your account information.

Using optical disk drives

Operating Basics

The full-size drive provides high-performance execution of CD/DVD-ROMbased programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an adaptor. A Serial ATA interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVDROM, an indicator on the drive glows.

Use the DVD playback application to view DVD-Video discs.

User’s Manual 4-14

Loading discs

To load CD/DVD's, follow the steps as listed below and refer to figures 4-4 to 4-6.

1. When the computer's power is on, press the eject button to open the disc tray slightly.

Eject button

Operating Basics

Figure 4-4 Pressing the eject button

2. Grasp the disc tray gently and pull until it is fully opened.

Disc Tray

Figure 4-5 Pulling the disc tray open

User’s Manual 4-15

Operating Basics

3. Lay the CD/DVD, label side up, in the disc tray.

Laser lens

Figure 4-6 Inserting a CD/DVD

When the disc tray is fully opened, the edge of the computer will extend slightly over the area where you insert the media. Therefore, when loading a CD or DVD, you will need to turn it slightly at an angle when you place it in the disc tray. After loading the CD/DVD you should ensure that it is properly positioned over the central spindle and that it lies flat within the tray.

■ Do not touch either the laser lens or the area immediately around it -

doing so could cause misalignment and may damage the drive.

■ Make sure that no foreign objects are inserted into or otherwise enter

the drive. Check the disc tray, especially the area behind the front edge, to ensure that there are no foreign objects or material present before closing the drive.

4. Press the center of the CD/DVD gently until you feel it click into place on the center spindle. The disc should be slightly below the top of the spindle and flush with the spindle base.

5. Press the center of the disc tray in order to close it - the tray will click into place when it is locked.

If the CD/DVD is not seated properly when the disc tray is closed, you may find that the media itself might become damaged, and/or the disc tray might not open fully when you next press the eject button.

User’s Manual 4-16

Removing discs

To remove CD/DVD's, follow the steps as listed below.

Do not press the eject button while the computer is accessing the media in the drive, instead wait for the indicator to go out before you open the disc tray. In addition, if the CD/DVD media is spinning when you open the tray, wait for it to fully stop before you remove it.

1. When the computer's power is on, press the eject button to open the disc tray slightly and then gently pull it out of the system until it is fully opened.

After the disc tray has opened slightly, you should wait for a moment to ensure the CD/DVD media has stopped spinning before you fully open the tray.

2. The CD/DVD media will extend slightly over the sides of the disc tray in order that you can hold it. Grasp it carefully by its edges and lift it vertically off of the central spindle and out of the tray.

Operating Basics

Figure 4-7 Removing a CD/DVD

3. Press the center of the disc tray in order to close it - the tray will click into place when it is locked.

User’s Manual 4-17

Operating Basics

How to remove a CD/DVD when the disc tray will not open

Pressing the eject button will not open the disc tray when the computer is turned off although, in these circumstances, you can open the tray by inserting a slender object such as a straightened paper clip about 15mm into the eject hole just to the right of the drive's eject button.

Disc Tray LED

Eject button

Figure 4-8 Manual release with the eject hole

You must ensure that you turn off the power before you use the eject hole. If the CD/DVD media is spinning when you open the disc tray, it may fly off of the spindle and cause injury.

Writng CD/DVD on DVD Super Multi drives

The optical drive installed on this computer cannot write multiple sessions on DVD-R Dual Layer disc sessions. Once a disc has been written to once, it will be finalized. Once finalized, no further writing to the disc will be possible regardless of what portion of the total disc capacity was used.

You can use the DVD-R drive to write data to either CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW, DVD-RAM, or DVD-R (Dual Layer) discs.

TOSHIBA Disc Creator and Ulead DVD MovieFactory are provided as writing software with this computer.

Ulead DVD MovieFactory can be used to write files in video format. TOSHIBA Disc Creator can be used to write data.

Eject hole

User’s Manual 4-18

■ Please refer to the Writable discs, Chapter 2 for details about the types

of writable CD and DVD discs that can be supported by this computer.

■ Do not turn off the power to the optical disc drive while the computer is

accessing it as this may cause you to lose data.

■ CD-R/RW media cannot be accessed using the Create CD/DVD option

in Media Center.

■ To write data to CD-R/-RW media, use the TOSHIBA Disc Creator

feature that is installed on your computer.

When writing information to media using an optical drive, you should always ensure that you connect the AC adaptor to a live power socket. It is possible that, if data is written while powered by the battery pack, the write process may sometimes fail due to low battery power - in these instances data loss may occur.

Important message

Before you write or rewrite to any of the media supported by the DVD Super Multi drive, please read and follow all of the setup and operating instructions in this section. If you fail to do so, you may find that theDVD Super Multi drive drive may not function properly, and you may fail to write or rewrite information successfully - this may cause you to either lose data or incur other damage to the drive or media.

Operating Basics

Disclaimer

TOSHIBA does not bear responsibility for the following:

■ Damage to any CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW,

DVD+R, DVD+R (Double Layer), DVD+RW or DVD-RAM disc that may be caused by writing or rewriting with this product.

■ Any change or loss of the recorded contents of CD-R, CD-RW, DVD-R,

DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW or DVD-RAM media that may be caused by writing or rewriting with this product, or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents.

■ Damage that may be caused by using third party equipment or

software.

Given the technological limitations of current optical disc writing drives, you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices. In view of this, it is good practice to make two or more copies of important data, in case of any undesired change or loss of the recorded contents.

User’s Manual 4-19

Before writing or rewriting

■ Based on TOSHIBA's limited compatibility testing, we suggest the

following manufacturers of CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW or DVDRAM media, however, it must be noted that disc quality can affect write or rewrite success rates. Please also be aware that in no event does TOSHIBA guarantee the operation, quality or performance of any disc.

CD-R:

TAIYO YUDEN CO., Ltd. MITSUBISHI KAGAKU MEDIA CO., LTD. Ricoh Co., Ltd. Hitachi Maxell,Ltd.

CD-RW: (Multi-Speed and High-Speed)

MITSUBISHI KAGAKU MEDIA CO., LTD. Ricoh Co., Ltd.

CD-RW: (Ultra-Speed)

MITSUBISHI KAGAKU MEDIA CO., LTD.

DVD-R:

DVD Specifications for Recordable Disc for General Version 2.0

TAIYO YUDEN Co.,Ltd. (for 8x and 16x speed media) MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x, 8x and 16x speed media) Hitachi Maxell,Ltd. (for 8x and 16x speed media)

Operating Basics

DVD-R (Dual Layer):

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x and 8x speed media)

DVD-R for Labelflash:

FUJIFILM CORPORATION (for 16x speed media)

DVD+R:

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x and 16x speed media) Ricoh Co., Ltd. (for 8x and 16x speed media) TAIYO YUDEN CO., Ltd. (for 8x and 16x speed media)

DVD+R (Double Layer):

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2.4x and 8x speed media)

DVD+R for Labelflash:

FUJIFILM CORPORATION (for 16x speed media)

User’s Manual 4-20

Toshiba ML3054 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Table of Contents

Copyright

Disclaimer

Trademarks

Macrovision License

FCC information

EU Conformity Statement

VCCI Class B Information

Important Safety Information for Computers with TV tuner

Modem warning notice

Japan regulations

Instructions for IC CS-03 certified equipment

Notes for Users in Australia and New Zealand

Optical disc drive safety instructions

International precautions

Preface

Conventions

General Precautions

Provide adequate ventilation

Creating a computer-friendly environment

Stress injury

Heat injury

Pressure or impact damage

Mobile phones

Instruction Manual for Safety and Comfort

The cautions on use of a Qosmio F50 series computer

Introduction

Equipment checklist

Chapter 1

Hardware

Special features

TOSHIBA Value Added Package

Utilities and Applications

Optinal accessories

The Grand Tour

Front with the display closed

Chapter 2

Left side

Right side

Back

Underside

Front with the display open

System indicators

Optical disc drives

AC adaptor

Getting Started

Chapter 3

Connecting the AC adaptor

Opening the display

Turning on the power

Starting up for the first time

Turning off the power

Restarting the computer

System Recovery Options

System Recovery

Operating Basics

Using the Touch Pad

Chapter 4

AV Controller

Using the Fingerprint Sensor

Web Camera

Using TOSHIBA Face Recognition

Using optical disk drives

Writng CD/DVD on DVD Super Multi drives