Toshiba MD13P1 User Manual

DIGITAL VIDEO

Introduction

COMBINATION COLOR TELEVISION AND DVD VIDEO PLAYER

MD13P1

OWNER’S MANUAL

Connections

Basic setup

TV operation

Basic playback

Advanced playback

Function setup

Others

5K30401B [E] (Cover) 20/4/04, 15:261

Introduction

IMPORTANT SAFEGUARDS

The lightning flash with arrowhead symbol, within an equilateral

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE P ARTS INSIDE. REFER SER VICING TO QUALIFIED SER VICE PERSONNEL.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE.

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

- Reorient or relocate the receiving antenna.

- Increase the distance between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance with

the FCC (Federal Communications Commission) Rules could void the user's authority to operate this equipment.

event that third party copyrights and other rights are not violated.

CAUTION:

THIS DIGIT AL VIDEO PLAYER EMPLOYS A LASER SYSTEM.

Location of the required Marking

The rating sheet and the safety caution are on the rear of the unit.

TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS OWNER'S MANUAL CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SER VICE PROCEDURE.

USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO NOT ST ARE INT O BEAM.

5K30401B [E] (P02-05) 20/4/04, 15:262

CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J.

IMPORTANT SAFEGUARDS

1. READ INSTRUCTIONS

All the safety and operating instructions should be read before the unit is operated.

2. RETAIN INSTRUCTIONS

The safety and operating instructions should be retained for future reference.

3. HEED WARNINGS

All warnings on the unit and in the operating instructions should be adhered to.

4. FOLLOW INSTRUCTIONS

All operating and use instructions should be followed.

5. CLEANING

Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning the exterior cabinet only.

6. ATTACHMENTS

The manufacturer of this unit does not make any recommendations for attachments, as they may cause hazards.

7. WATER AND MOISTURE

Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.

8. ACCESSORIES

Do not place this unit on an unstable cart, stand, tripod, bracket, or table. The unit may fall, causing serious injury, and serious damage to the unit.

8A. An appliance and cart combination should be moved with care. Quick stops,

excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

9. VENTILATION

Slots and openings in the cabinet back or bottom are provided for ventilation, and to ensure reliable operation of the unit, and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

10. POWER SOURCE

This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For units intended to operate from battery power, or other sources, refer to the respective pages on this Owner's Manual for their operating instructions.

11. GROUNDING OR POLARIZATION

This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Instead of the polarized alternating-current line plug, your unit may be equipped with a 3-wire grounding-type plug (a plug having a third (grounding) pin). This plug will only fit into a grounding-type power outlet. This too, is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

12. POWER-CORD PROTECTION

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

PORT ABLE CAR T WARNING

(symbol provided by RETAC)

S3126A

Introduction

5K30401B [E] (P02-05) 20/4/04, 15:263

Introduction

IMPORTANT SAFEGUARDS

13. LIGHTNING

T o protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges.

14. POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.

15. OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

16. OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

17. OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the National Electrical Code (NEC), ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

18. SERVICING

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. For example: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the unit. c. If the unit has been exposed to rain or water. d. If the unit does not operate normally by following the operating instructions. Adjust only those

controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the

unit to its normal operation. e. If the unit has been dropped or the cabinet has been damaged. f. When the unit exhibits a distinct change in performance, this indicates a need for service.

19. REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

20. SAFETY CHECK

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.

21. HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

22. DISC TRAY

Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.

23. CONNECTING

When you connect the product to other equipment, turn off the power and unplug all of the equipment from the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's manual of the other equipment carefully and follow the instructions when making any connections.

24. SOUND VOLUME

Reduce the volume to the minimum level before you turn on the product. Otherwise, sudden high volume sound may cause hearing or speaker damage.

25. SOUND DISTORTION

Do not allow the product output distorted sound for a longtime. It may cause speaker overheating and fire.

26. HEADPHONES

When you use the headphones, keep the volume at a moderate level. If you use the headphones continuously with high volume sound, it may cause hearing damage.

(Continued)

5K30401B [E] (P02-05) 20/4/04, 15:264

27. LASER BEAM

Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the laser beam. It may cause sight damage.

28. DISC

Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and product malfunction.

29. NOTE TO CABLE TV SYSTEM INSTALLER

This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

EXAMPLE OF ANTENNA GROUNDING AS PER THE

NATIONAL ELECTRICAL CODE

ANTENNA LEAD IN WIRE

GROUND

CLAMP

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

Introduction

ELECTRIC SERVICE

EQUIPMENT

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

NEC-NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

S2898A

IMPORTANT RECYCLING INFORMATION

This product uses both Cathode Ray T ube (CRT) and other components that contain lead. In your community there might be regulations that require you to dispose these materials properly under environmental considerations. Please contact your local authorities, or the Electronic Industries Alliance (http://www.eiae.org) for disposal or recycling information.

Power source

AC Outlet

Wider Hole and Blade

Polarized AC Cord Plug (One blade is wider than the other.)

TO USE AC POWER SOURCE

Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug into a standard 120V 60Hz polarized AC outlet.

Notes:

Never connect the AC line cord plug to other than the specified voltage (120V

• 60Hz). Use the attached power cord only. If the polarized AC cord does not fit into a non-polarized AC outlet, do not attempt to

• file or cut the blade. It is the user’s responsibility to have an electrician replace the obsolete outlet. If you cause a static discharge when touching the unit and the unit fails to function,

• simply unplug the unit from the AC outlet and plug it back in. The unit should return to normal operation. If the AC cord plug is plugged in for the first time, wait for approx. 5 seconds before

• pressing the POWER button.

5K30401B [E] (P02-05) 20/4/04, 15:265

Introduction

Precautions

Notes on handling

3 When shipping the unit, the original shipping carton

and packing materials come in handy. For maximum protection, repack the unit as it was originally packed at the factory.

3 Do not use volatile liquids, such as insect spray, near

the unit. Do not leave rubber or plastic products to contact the unit for prolonged period. They will leave marks on the finish.

3 The top and rear panels of the unit may become

warm after a long period of use. This is not a malfunction.

3 When the unit is not in use, be sure to remove the

disc and turn off the power.

3 If you do not use the unit for a long period, the unit

may not function properly in the future. Turn on and use the unit occasionally.

Notes on locating

3 Place the unit on a level surface. Do not use it on a

shaky or unstable surface such as a wobbling table or inclined stand. The loaded disc may become disaligned and damage the unit.

3 When you place this unit near a TV, radio, or VCR,

the playback picture may become poor and the sound may be distorted. In this case, place the unit away from the TV, radio, or VCR.

Notes on moisture condensation

Moisture condensation damages the unit. Please read the following carefully.

Moisture condensation occurs, for example, when you pour a cold drink into a glass on a warm day. Drops of water form on the outside of the glass. In the same way, moisture may condense on the optical pick-up lens inside this unit, one of the most crucial internal parts of the unit.

3 Moisture condensation occurs during the

following cases.

When you bring the unit directly from a cold place to a warm place. When you use the unit in a room where you just turned on the heater, or a place where the cold wind from the air conditioner directly hits the unit. In summer, when you use the unit in a hot and humid place just after you move the unit from an air conditioned room. When you use the unit in a humid place.

Optical pick-up

lens

Notes on cleaning

Use a soft, dry cloth for cleaning.

For stubborn dirt, soak the cloth in a weak detergent solution, wring well and wipe. Use a dry cloth to wipe it dry.

Do not use any type of solvent, such as thinner and benzine, as they may damage the surface of the unit. If you use a chemical saturated cloth to clean the unit, follow that product’s instructions.

To obtain a clear picture

The unit is a high technology, precision device. If the optical pick-up lens and disc drive parts are dirty or worn down, the picture quality will deteriorate. To obtain a clear picture, we recommend regular inspection and maintenance (cleaning or parts replacement) every 1,000 hours of use depending on the operating environment. For details, contact your nearest dealer.

3 Do not use the unit when moisture condensation

may occur.

If you use the unit in such a situation, it may damage discs and internal parts. Remove the disc, connect the power cord of the unit to the wall outlet, turn on the unit, and leave it for two or three hours. After two or three hours, the unit will have warmed up and evaporated any moisture. Keep the unit connected to the wall outlet and moisture condensation will seldom occur.

Wait!

Wall outlet

5K30401B [E] (P06-07) 20/4/04, 15:266

Notes on discs

On handling discs

Do not touch the playback side of the disc.

Playback side

Do not attach paper or tape to discs.

On cleaning discs

Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the center outwards with a soft cloth. Always keep the disc clean.

Structure of disc contents

Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. Video CDs and Audio CDs are divided into tracks.

DVD video disc

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3

Video CD/Audio CD

Track 1 Track 2 Track 3 Track 4 Track 5

Each title, chapter or track is assigned a number, which is called “title number”, “chapter number” or “track number” respectively. There may be discs that do not have these numbers.

Introduction

If you cannot wipe off the dust with a soft cloth, wipe the disc lightly with a slightly moistened soft cloth and finish with a dry cloth. Do not use any type of solvent such as thinner, benzine, commercially available cleaners or antistatic spray for vinyl LPs. It may damage the disc.

On storing discs

Do not store discs in a place subject to direct sunlight or near heat sources. Do not store discs in places subject to moisture and dust such as a bathroom or near a humidifier. Store discs vertically in a case. Stacking or placing objects on discs outside of their case may cause warping.

Notes on copyright

It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, and rent copyrighted material without permission.

DVD video discs are copy protected, and any recordings made from these discs will be distorted.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

5K30401B [E] (P06-07) 20/4/04, 15:267

Introduction

Notes on discs (Continued)

About this owner’s manual

This owner’s manual explains the basic instructions of this unit. Some DVD video discs are produced in a manner that allows specific or limited operation during playback. As such, the unit may not respond to all operating commands. This is not a defect in the unit. Refer to instruction notes of discs.

” may appear on the TV screen during operation.

“

” means that the operation is not permitted by the

A “ unit or the disc. For example, sometimes it is unable to stop the playback of copyright message of the disc when the STOP (3) button is pressed. Alternatively, the “

” may

also indicate that the feature is not available for the disc.

Notes on region numbers

The region number of this unit is 1. If region numbers, which stand for their playable area, are printed on your

ALL

DVD video disc and you do not find

, disc playback will not be allowed by the player. (In this case, the unit will display a message on-screen.)

On Video CDs

This DVD supports Video CDs equipped with the PBC (Version 2.0) function. (PBC is the abbreviation of Playback Control.) You can enjoy two playback variations depending on types of discs.

• Video CD not equipped with PBC function

(Version 1.1)

Sound and movie can be played on this DVD in the same way as an audio CD.

• Video CD equipped with PBC function

(Version 2.0)

In addition to operation of a Video CD not equipped with the PBC function, you can enjoy playback of interactive software with search function by using the menu displayed on the TV screen (Menu Playback). Some of the functions described in this owner’s manual may not work with some discs.

Playable discs

This unit can play the following discs.

Disc Mark

DVD video discs

Video CDs

Audio CDs

The following discs are also available.

Some of these discs may be incompatible.

DIGITAL VIDEO

CD-R/CD-RW discs of CD-DA, Video CD or JPEG format Kodak Picture CD and FUJICOLOR CD format

Contents

Audio Video

(moving

pictures)

Audio Video

(moving

pictures)

Audio

Disc

Size

12 cm

8 cm

12 cm

8 cm

12 cm

8 cm

(CD

single)

• You cannot play discs other than those listed above.

• You cannot play discs of DVD-RAM, DVD-ROM, Photo CD, etc., or non standardized discs even if they may be labeled as above.

• Some CD-R/RWs can not be played back depending on the recording conditions.

• This unit uses the NTSC color system, and cannot play DVD video discs recorded in any other color system (PAL, SECAM, etc.).

Maximum

playback time

Approx. 4 hours

(single sided disc)

Approx. 8 hours

(double sided disc)

Approx. 80 minutes

(single sided disc)

Approx. 160 minutes

(double sided disc)

Approx. 74 minutes

Approx. 20 minutes

Approx. 74 minutes

Approx. 20 minutes

5K30401B [E] (P08-12) 20/4/04, 15:268

Contents

Introduction

IMPORTANT SAFEGUARDS............................2

Precautions .......................................................6

Notes on discs...................................................7

Contents............................................................9

Identification of controls ..................................10

Connections

Antenna connections.......................................13

Cable TV connections .....................................14

Connecting to optional equipment...................15

Basic setup

Starting setup ..................................................18

Setting the language .......................................19

TV operation

TV operation....................................................20

Closed captions...............................................22

To memorize channels ....................................23

Setting the V-Chip ...........................................24

Picture control adjustment...............................26

Adjusting the picture preference .....................26

Stereo and Second Audio Program (SAP)......27

Basic playback

Playing a disc ..................................................28

Advanced playback

Zooming ......................................................... 31

Locating desired scene .................................. 31

Repeat playback ............................................ 32

A-B Repeat playback ..................................... 32

Program playback .......................................... 33

Random playback .......................................... 33

Changing angles ............................................ 34

Title selection ................................................. 34

DVD menu...................................................... 34

Changing soundtrack language ..................... 35

Subtitles ......................................................... 35

Karaoke playback........................................... 36

Disc status...................................................... 36

To turn off the PBC ........................................ 36

JPEG playback............................................... 37

Function setup

Customizing the function settings .................. 38

Temporary disabling of rating level

by DVD disc ................................................... 41

Others

Language code list ......................................... 42

Reception disturbances.................................. 43

Problems and troubleshooting ....................... 44

Specifications ................................................. 46

LIMITED WARRANTY ................................... 47

Introduction

5K30401B [E] (P08-12) 20/4/04, 15:269

Introduction

Identification of controls

See the page in for details.

Front

Rear

POWER indicator

POWER button

Remote sensor

OPEN/CLOSE ( ) button

VOLUME ( / ) buttons

AUDIO (L/R)/VIDEO IN jacks (LINE)

Disc tray

STOP( ) button

PLAY ( ) button

CHANNEL ( / ) buttons

PHONES jack

SKIP ( / ) buttons

5K30401B [E] (P08-12) 20/4/04, 15:2610

AC power cord

COAXIAL DIGITAL AUDIO OUT jack

RF IN jack

Remote control

The instructions in this manual describe the function on the remote control. See the page in for details.

Introduction

TV/DVDRECALL

321

654

7 9

SLEEP

CLOSED

CAPTION

TOP MENU

SETUP/MENU DVD MENU

VOL – VOL +

RETURN

REV

SKIP STOP SKIP JUMP

AUDIO

SUBTITLE

CH +

CH –

PLAY FWD PLAY MODE

POWER

INPUT SELECT

GAME

OPEN/CLOSE

MUTE

ANGLE

ZOOM/CH RTNCANCEL

ENTER

*DVD MENU button

Use the DVD MENU button to display the menu included on many DVD video discs. To operate a menu, follow the

instructions in “DVD menu.”

5K30401B [E] (P08-12) 20/4/04, 15:2611

SLOW PAUSE SLOW REPEAT A–B

Introduction

Inserting batteries

Slide the battery compartment

1 2 3

cover in the direction of the arrow.

Install two “AAA” batteries (supplied), paying attention to the polarity diagram in the battery compartment.

Replace the compartment cover.

Operation

• Aim the remote control at the remote sensor and press control buttons to operate.

• Operate the remote control within 30° angle on either side of the remote sensor, up to a distance of approx. 5 meters.

Approx. 5 meters

The precautions below should be followed when using batteries in this device:

1. Use only the size and type of batteries specified.

2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.

Reversed batteries may cause damage to the device.

Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.

4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from

possible battery leakage.

5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture (follow battery

manufacturer’s directions).

5K30401B [E] (P08-12) 20/4/04, 15:2612

Connections

Antenna connections

If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system. If you are using a cable TV service (CABLE), see page 14 for Cable TV connections.

Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm twin-lead wire)

Antenna

jack

Antenna

jack

Connect the 75 ohm cable from the combination VHF/UHF antenna to the antenna jack.

If your combination VHF/UHF antenna has a 300 ohm twin-lead wire, the use of the 300-75 ohm

75 ohm coaxial cable (not supplied)

300-75 ohm matching transformer (supplied)

matching transformer may be necessary.

Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm twin-lead wires)

Antenna

jack

Combiner (not supplied)

300-75 ohm matching transformer (supplied)

Connect the UHF 300 ohm twin-lead wire to the combiner (not supplied). Connect the VHF 300 ohm twin-lead wire to the 300-75 ohm matching transformer. Attach the transformer to the combiner, then attach the combiner to the antenna jack.

Connections

UHF 300 ohm twin-lead wire (not supplied)

VHF 300 ohm twin-lead wire (not supplied)

Separate VHF/UHF antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)

Antenna

jack

VHF 75 ohm (not supplied)

Combiner (not supplied)

UHF 300 ohm twin-lead wire (not supplied)

5K30401B [E] (P13-23) 20/4/04, 15:2613

Connect the VHF 75 ohm cable and UHF 300 ohm twin-lead wire to the combiner (not supplied). Attach the combiner to the antenna jack.

Connections

Cable TV connections

This TV/DVD has an extended tuning range and can tune most cable channels without using a Cable TV converter box. Some cable companies offer “premium pay channels” in which the signal is scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by the cable company.

For subscribers to basic cable TV service

75 ohm coaxial cable

Antenna

jack

For basic cable service not requiring a converter/descrambler box, connect the Cable TV 75 ohm coaxial cable directly to the Antenna jack on the back of the TV/DVD.

For subscribers to scrambled cable TV service

If you subscribe to a cable TV service which requires the use of a converter/descrambler box, connect the incoming 75 ohm coaxial cable to the converter/descrambler box. Using another 75 ohm coaxial cable, connect the output jack of the converter/descrambler box to the antenna jack on the TV/DVD. Follow the connections shown below. Set the TV/DVD to the output channel of the converter/descrambler box (usually channel 3 or 4) and use the converter/descrambler box to select channels.

Incoming 75 ohm Cable TV

Converter/

descrambler

75 ohm cable to TV/DVD

Antenna

jack

For subscribers to unscrambled basic cable TV service with scrambled premium channels

If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the use of a converter/descrambler box, you may wish to use a signal splitter and an A/B Switch box (available from the cable company or an electronics supply store). Follow the connections shown below. With the switch in the “B” position, you can directly tune any nonscrambled channels on your TV/DVD. With the switch in the “A” position, tune your TV/DVD to the output of the converter/descrambler box (usually channel 3 or 4) and use the converter/ descrambler box to tune scrambled channels.

Incoming 75 ohm Cable TV

Splitter

Converter/

descrambler

A/B switch

75 ohm cable

to TV/DVD

Antenna

jack

5K30401B [E] (P13-23) 20/4/04, 15:2714

Connecting to optional equipment

You can enjoy VCR, camcorder or TV game with connection to external input. To select the external input, press INPUT SELECT and select “LINE” mode.

To connect the TV/DVD to a VCR

Press the INPUT SELECT to select the “LINE” (external input) to use the TV as a monitor. Operate your VCR as usual.

: Signal flow

VCR

Front of TV/DVD

VIDEO IN

INPUT SELECT GAME

Connections

To Audio/Video OUT

Audio/Video cable (not supplied)

AUDIO IN (R) AUDIO IN (L)

To connect the TV/DVD to a camcorder

To playback from the camcorder, connect the camcorder to the TV/DVD as shown.

: Signal flow

Camcorder

VIDEO IN

To Audio/Video OUT

Audio/Video cable (not supplied)

Front of TV/DVD

AUDIO IN (R) AUDIO IN (L)

To connect the TV/DVD to a TV Game

You can enjoy playing a TV game on the screen by adjusting to suitable brightness for your eyes.

1. Connect a TV Game to the TV/DVD.

2. Press GAME. The GAME mode screen appears.

• This TV/DVD has the GAME mode function (see page 21).

: Signal flow

VIDEO IN

Front of TV/DVD

To Audio/Video OUT

Audio/Video cable (not supplied)

Notes:

• You can also change the TV screen to LINE by pressing CH +/– buttons.

• The TV/DVD can also be used as a display device for many video games. However, due to the wide variety of different types of signal generated by these devices and subsequent hook-up variations required, they have not all been included in the suggested connection diagrams. You'll need to consult each component's Owner's Manual for additional information.

5K30401B [E] (P13-23) 20/4/04, 15:2715

AUDIO IN (R) AUDIO IN (L)

+ 33 hidden pages