Toshiba L450D, L450 User Manual

Download

User’s Manual

L450/L450D

computers.toshiba-europe.com

L450/L450D

Disclaimer

© 2009 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.

TOSHIBA L450/L450D Portable Personal Computer User’s Manual

First edition September 2009 Copyright authority for music, movies, computer programs, databases and

other intellectual property covered by copyright laws belongs to the author or to the copyright owner. Copyrighted material can be reproduced only for personal use or use within the home. Any other use beyond that stipulated above (including conversion to digital format, al teration, transfer of copied material and distribution on a network) without the permission of the copyright owner is a violation of copyright or author’s rights and is subject to civil damages or criminal action. Please comply with copyright laws in making any reproduction from this manual.

This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the TOSHIBA L450/L450D Portable Personal Computers at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice. TOSHIBA assumes no liability for damages incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manual.

Trademarks

IBM is a registered trademark and IBM PC is a trademark of International Business Machines Corporation.

Intel, Intel Core, Celeron, Centrino and Pentium are registered trademarks or trademarks of Intel Corporation.

Microsoft and Windows Corporation.

DirectX, ActiveDesktop, DirectShow, and Windows Media are registered trademarks of Microsoft Corporation.

Adobe and Photoshop are either registered trademarks ot trademarks of Adobe Systems Incorporated.

ConfigFree is a trademark of TOSHIBA Corporation. HDMI, the HDMI logo and High-Definition Multimedia Interface are

trademarks or registered trademarks of HDMI Licensing LLC. LabelFlash™ is a trademark of YAMAHA Corporation. Photo CD is a trademark of Eastman Kodak. Wi-Fi is a registered trademark of the Wi-Fi Alliance.

ii User’s Manual

are registered trademarks of Microsoft

Memory Stick and Memory Stick PRO are registered trademarks of SONY Corporation.

Secure Digital and SD are trademarks of the SD Card Association. MultiMediaCard and MMC are trademarks of MultiMediaCard Association. Other trademarks and registered trademarks not listed above may be used

in this manual.

Macrovision License of Notice

For DVD Manufacturing License Agreement

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights, including U.S. Patent Numbers 6,836,549; 6,381,747; 7,050,698; 6,516,132 and 5,583,936. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. The copyright protection technology availability depends on the model you purchased.

EU Declaration of Comformity

This product and - if applicable - the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC and/or R&TTE Directive 1999/5/EC.

Responsible for CE-marking: TOSHIBA EUROPE GMBH, Hammfelddamm 8, 41460 Neuss, Germany Manufacturer: Toshiba Corporation, 1-1 Shibaura 1-chome, Minato-ku, Tokyo, 105-8001,

Japan The complete official EU CE Declaration can be obtained on following

internet page: http://epps.toshiba-teg.com/

L450/L450D

CE compliance

This product is labelled with the CE Mark in accordance with the related European Directives, notably Electromagnetic Compatibility Directive 2004/108/EC for the notebook and the electronic accessories including the supplied power adapter, the Radio Equipment and Telecommunications Terminal Equipment Directive 1999/5/EC in case of implemented telecommunication accessories and the Low Voltage Directive 2006/95/EC for the supplied power adapter.

User’s Manual iii

L450/L450D

This product and the original options are designed to observe the related EMC (Electromagnetic Compatibility) and safety standards. However, TOSHIBA cannot guarantee that this product still observes these EMC standards if options or cables not produced by TOSHIBA are connected or implemented. In this case the persons who have connected / implemented those options / cables have to provide assurance that the system (PC plus options / cables) still fulfils the required standards. To avoid general EMC problems, the following guidance should be noted:

■ Only CE marked options should be connected / implemented

■ Only best shielded cables should be connected

Working environment

This product was designed to fulfil the EMC (Electromagnetic Compatibility) requirements to be observed for so-called “Residential, commercial and light industry environments”.

TOSHIBA do not approve the use of this product in working environments other than the above mentioned “Residential, commercial and light industry environments”.

For example, the following environments are not approved:

■ Industrial Environments (e.g. environments where a mains voltage of

■ Medical Environments

■ Automotive Environments

■ Aircraft Environments

Any consequences resulting from the use of this product in working environments that are not approved are not the responsibility of TOSHIBA.

The consequences of the use of this product in non-approved working environments may be:

■ Interference with other devices or machines in the near surrounding

■ Malfunction of, or data loss from, this product caused by disturbances

Therefore TOSHIBA strongly recommend that the electromagnetic compatibility of this product should be suitably tested in all non-approved working environments before use. In the case of automobiles or aircraft, the manufacturer or airline respectively should be asked for permission before use of this product.

Furthermore, for general safety reasons, the use of this product in environments with explosi ve atmospheres is not permitted.

380 V three-phase is used)

area.

generated by other devices or machines in the near surrounding area.

iv User’s Manual

Following information is only for EU-member states:

Disposal of products

The crossed out wheeled dust bin symbol indicates that products must be collected and disposed of separately from household waste. Integrated batteries and accumulators can be disposed of with the product. They will be separated at the recycling centres.

The black bar indicates that the product was placed on the market after August 13, 2005.

By participating in separate collection of products and batteries, you will help to assure the proper disposal of products and batteries and thus help to prevent potential negative consequences for the environment and human health.

For more detailed information about the collection and recycling programmes available in your country, please visit our website (http://eu.computers.toshiba-europe.com) or contact your local city office or the shop where you purchased the product.

Disposal of batteries and/or accumulators

The crossed out wheeled dust bin symbol indicates that batteries and/or accumulators must be collected and disposed of separately from household waste.

3E+J&G

If the battery or accumulator contains more than the specified values of lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery Directive (2006/66/EC), then the chemical symbols for lead (Pb), mercury (Hg) and/or cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.

By participating in separate collection of batteries, you will help to assure the proper disposal of products and batteries and thus help to prevent potential negative consequences for the environment and human health.

L450/L450D

This symbol may not be displayed depending on the country and region where you purchased.

User’s Manual v

L450/L450D

Disposing of the computer and the computer’s batteries

■ Discard this computer in accordance with applicable laws and

regulations. For further information, contact your local government.

■ This computer contains rechargeable batteries. After repeated use, the

batteries will finally lose their ability to hold a charge and you will need to replace them. Under certain applicable laws and regulation, it may be illegal to dispose of old batteries by placing them in the trash.

■ Please be kind to our shared environment. Check with your local

government authority for details regarding where to recycle old batteries or how to dispose of them properly. This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government.

ENERGY STAR® Program

Your Computer model may be ENERGY STAR purchased is qualified, it is label ed with the ENERGY STAR logo on the computer and the following information applies.

TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency. Your computer ships with the power management options preset to a configuration that will provide the most stable operating environment and optimum system performance for both AC power and battery modes.

To conserve energy, your computer is set to enter the low-power Sleep mode which shuts down the system and display within 15 minutes of inactivity in AC power mode. TOSHIBA recommends that you leave this and other energy saving features active, so that your computer will operate at its maximum energy efficiency. You can wake the computer from Sleep mode by pressing the power button.

Products that earn the ENERGY STAR prevent greenhouse gas emissions by meeting strict energy efficiency guidelines set by the US EPA and the EU Commission. According to the EPA, a computer meeting the new ENERGY STAR specifications will use between 20% and 50% less energy depending on how it is used.

Visit http://www.eu-energystar.org or http://www.energystar.gov for more information regarding the ENERGY STAR Program.

qualified. If the model you

REACH - Compliance Statement

The new European Union (EU) chemical regulation, REACH (Registration, Evaluation, Authorization and Restriction of Chemicals), entered into force on 1 June 2007. Toshiba will meet all REACH requirements and is committed to provide our customers with information about the chemical substances in our products according to REACH regulation.

vi User’s Manual

Please consult the following website www.toshiba-europe.com/computers/

info/reach for information about the presence in our articles of substances

included on the candidate list according to article 59(1) of Regulation (EC) No 1907/2006 (“REACH”) in a concentration above 0.1 % weight by weight.

Following information is only for Turkey:

■ Compliant with EEE Regulations: Toshiba meets all requirements of

Turkish regulation 26891 “Restriction of the use of certain hazardous substances in electrical and electronic equipment”.

■ The number of possible pixel failures of your display is defined

according to ISO 13406-2 standards. If the number of pixel failures is less than this standard, they will not be counted as defect or failure.

■ Battery is a consumption product, since the battery time depends on the

usage of your computer. If the battery can not be charged at all, then it is a defect or failure. The changes in battery time is not a defect or failure.

GOST

L450/L450D

Optical disc drive standards

TOSHIBA L450/L450D computers are shipped with a DVD Super Multi (+-R DL) drive preinstalled.

The drive has one of the following labels:

CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE APPAREIL A LASER DE CLASSE1 KLASS 1 LASER APP ARAT

Before it is shipped, the Class 1 Laser is certified to meet the United States Chapter 21 S tandards of the Department of Health and Human Services (DHHS 21 CFR).

For any other country, the drive is certified to meet the Class 1 Laser standards of IEC825 and EN60825.

User’s Manual vii

L450/L450D

Optical disc drive safety instructions

■ The drive employs a laser system. To ensure proper use of this

product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

DVD Super Multi (+-R DL) drive

Panasonic UJ890A/UJ890E

Location of the required label

COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J.

MANUFACTURED

Panasonic Communications Co., Ltd. 1-62, 4-Chome Minoshima Hakata-ku Fukuoka, Japan

viii User’s Manual

HLDS GT20N/GT20F

Location of the required label

COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J.

MANUFACTURED

Hitachi-LG Data Storage, Inc. 22-23, Kaigan 3-chome, Minato-Ku, Tokyo, 108-0022 Japan

Toshiba Samsung TS-L633C/TS-L633Y

L450/L450D

Location of the required label

PRODUCT IS CERTIFIED BY THE MANUFACTURER TO COMPLY WITH DHHS RULES 21 CFR CHAPTER 1, SUBCHAPTER J, APPLICABLE AT THE DATE OF MANUFACTURE.

MANUFACTURED

Toshiba Samsung Storage Technology Korea Corporation 14F Digital empireII, 486 sin-dong, YoungTong-gu, Suwon-si, Gyeonggi-do, Korea, 443-734

User’s Manual ix

L450/L450D

International precautions

CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” T o prevent direct exposure to the laser beam, do not try to open the enclosure.

VORSICHT: Dieses Gerät enthält ein Laser-System und ist als “LASERSCHUTZKLASSE 1 PRODUKT” klassifiziert. Für den richtigen Gebrauch dieses Modells lesen Sie bitte die Bedienungsanleitung sorgfältig durch und bewahren diese bitte als Referenz auf. Falls Probleme mit diesem Modell auftreten, benachrichtigen Sie bitte die nächste “autorisierte Service-Vertretung”. Um einen direkten Kontakt mit dem Laserstrahl zu vermeiden darf das Gerät nicht geöffnet werden.

x User’s Manual

ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.

APPARATET BOR KUN ÅBNES AF FAGFOLK MED SÆRLIGT KENDSKAB TIL APPARATER MED LASERSTRÅLER!

Indvendigt i apparatet er anbragt den her gengivne advarselsmækning, som advarer imod at foretage sådanne indgreb i apparatet, at man kan komme til at udsatte sig for laserstråling.

L450/L450D

OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1.

VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä.

CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS DURCHFÜHREN VON ANDEREN VORGÄNGEN ALS IN DER BEDIENUNGSANLEITUNG BESCHRIEBEN KÖNNEN GEFÄHRLICHE STRAHLENEXPOSITIONEN ZUR FOLGE HABEN.

Important notice

Copyrighted works including, but not limited to music, video, computer program, databases are protected by copyright laws. Unless specifically permitted under applicable copyright laws, you cannot copy, modify , assign, transmit or otherwise dispose of any copyrighted work with the consent of the owner of the copyright. Please take notice that unauthorized copying, modification, assignment, transmission and disposition may be subject to claims for damages and penalties.

■ Avoid using a telephone (other than a cordless type) during an electrical

storm. There may be a remote risk of electric shock from lightning.

■ Do not use the telephone to report a gas leak in the vicinity of the leak.

■ Use only the power cord indicated in this manual.

■ Replace only with the same or equivalent type battery recommended by

the manufacturer.

■ Dispose of used batteries according to the manufacturer’s instructions.

Use only the battery pack that came with the computer or an optional battery pack. Use of wrong battery could damage your computer. TOSHIBA assumes no liability for any damage in such case.

User’s Manual xi

L450/L450D

Preface General Precautions

Chapter 1 Introduction

Equipment checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3

Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-8

TOSHIBA Value Added Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-10

Utilities and Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-11

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-13

Chapter 2 The Grand Tour

Front with the display closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

Left side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4

Back side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4

Underside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5

Front with the display open. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7

System indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10

Optical disc drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12

AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-14

Chapter 3 Getting Started

Connecting the AC adaptor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2

Opening the display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4

Turning on the power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5

Starting up for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5

Turning off the power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6

Restarting the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9

System Recovery Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10

Chapter 4 Operating Basics

Using the Touch Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Using the optical disk drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2

Writing CD/DVD on DVD Super Multi drive . . . . . . . . . . . . . . . . . . . . .4-5

Media care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-14

Sound system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-16

Using the web camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-18

Using TOSHIBA Web Camera Application. . . . . . . . . . . . . . . . . . . . .4-19

xii User’s Manual

Using TOSHIBA Face Recognition . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23

LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

Cleaning the computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26

Moving the computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27

Heat dispersal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28

Chapter 5 The Keyboard

Typewriter keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Function keys: F1 … F12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Soft keys: FN key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Hot keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Windows special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

Keypad overlay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Generating ASCII characters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Chapter 6 Power and Power-up Modes

Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Power indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

Replacing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9

TOSHIBA Password Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11

Power-up modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13

Chapter 7 HW Setup and Passwords

HW Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

HW Setup Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

Chapter 8 Optional Devices

Bridge media slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

Additional memory module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

Battery Packs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7

Universal AC Adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7

Battery Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7

USB floppy diskette drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8

External monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11

Security lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13

Chapter 9 Troubleshooting

Problem solving process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

Hardware and system checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

TOSHIBA support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-20

Chapter 10 Disclaimers

L450/L450D

User’s Manual xiii

L450/L450D

Appendix A

Specifications

Environmental requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Appendix B Display Controller

Display controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Appendix C Wireless LAN

Card Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Radio Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Supported Frequency Sub-bands. . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Appendix D AC Power Cord and Connectors

Certification agencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1

Appendix E If your computer is stolen

Glossary Index

xiv User’s Manual

Preface

Congratulations on your purchase of the TOSHIBA L450/L450D computer. This powerful notebook computer provides excellent expansion capability, includes multimedia functionality, and is designed to provide years of reliable, high-performance computing.

This manual tells how to set up and begin using your computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.

If you are a new user of computers or if you’re new to portable computing, first read over the Introduction and The Grand Tour chapters to familiarize yourself with the computer’s features, components and accessory devices. Then read Getting Started for step-by-step instructions on setting up your computer.

If you are an experienced computer user, please continue reading the preface to learn how this manual is organized, then become acquainted with this manual by browsing through its pages. Be sure to read the Special

features section of the Introduction to learn about features that are

uncommon or unique to the computers and carefully read HW Setup and

Passwords. If you are going to connect external devices such as a printer,

be sure to read Chapter 8, Optional Devices.

L450/L450D

Manual contents

This manual is composed of the following chapters, appendixes, a glossary and an index.

Chapter 1, Introduction, is an overview of the computer’s features, capabilities, and options.

Chapter 2, The Grand Tour, identifies the components of the computer and briefly explains how they function.

Chapter 3, Getting Started, provides a quick overview of how to begin operating your computer.

Chapter 4, Operating Basics, includes tips on care of the computer and on using the Touch Pad, optical disc drive, Audio/Video controls, the web camera, the microphone, Wireless LAN and LAN.

Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hot keys.

Chapter 6, Power and Power-up Modes, gives details on the computer’s power resources and battery save modes.

User’s Manual xv

L450/L450D

Chapter 7, HW Setup and Passwords, explains how to configure the computer using the HW Setup program. It also tells how to set a password.

Chapter 8, Optional Devices, describes the optional hard ware available. Chapter 9, Troubleshooting, provides helpful information on how to perform

some diagnostic tests, and suggests courses of action if the computer doesn’t seem to be working properly.

Chapter 10, Disclaimers, provides Legal Footnotes information related to your computer.

The Appendixes provide technical information about your computer. The Glossary defines general computer terminology and includes a list of

acronyms used in the text. The Index quickly directs you to the information contained in this manual.

Conventions

This manual uses the following formats to describe, identify, and highlight terms and operating procedures.

Abbreviations

On first appearance, and whenever necessary for clarity, abbreviations are enclosed in parentheses following their definition. For example: Read Only Memory (ROM). Acronyms are also defined in the Glossary.

Icons

Icons identify ports, dials, and other parts of your computer. The indicator panel also uses icons to identify the components it is providing information on.

Keys

The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, ENTER identifies the ENTER key.

Key operation

Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, CTRL + C means you must hold down CTRL and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.

ABC

xvi User’s Manual

When procedures require an action such as clicking an icon or entering text, the icon’s name or the text you are to type in is represented in the typeface you see to the left.

Display

L450/L450D

ABC

Names of windows or icons or text generated by the computer that appear on its display screen are presented in the type face you see to the left.

Messages

Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below.

Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment.

Please read. A note is a hint or advice that helps you make best use of your equipment.

Indicates a potentially hazardous situation, which could result in death or serious injury, if you do not follow instructions.

Terminology

This term is defined in this document as follows:

Start

The word “Start” refers to the “ ” button in Windows

User’s Manual xvii

L450/L450D

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer.

Be certain to read the general precautions below and to note the cautions included in the text of the manual.

Creating a computer-friendly environment

Place the computer on a flat surface that is large enough for the computer and any other items you are using, such as a printer.

Leave enough space around the computer and other equipment to provide adequate ventilation. Otherwise, they may overheat.

To keep your computer in prime operating condition, protect your work area from:

■ Dust, moisture, and direct sunlight.

■ Equipment that generates a strong electromagnetic field, such as

stereo speakers (other than speakers that are connected to the computer) or speakerphones.

■ Rapid changes in temperature or humidity and sources of temperature

change such as air conditioner vents or heaters.

■ Extreme heat, cold, or humidity.

■ Liquids and corrosive chemicals.

Stress injur y

Carefully read the Instruction Manual for Safety and Comfort. It contains information on the prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use.

xviii User’s Manual

Heat injury

■ Avoid prolonged physical contact with the computer. If the computer is

used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer a low-heat injury.

■ If the computer has been used for a long time, avoid direct contact with

the metal plate supporting the various interface ports as this can become hot.

■ The surface of the AC adaptor can become hot when in use but this

condition does not indicate a malfunction. If you need to transport the AC adaptor, you should disconnect it and let it cool before moving it.

■ Do not lay the AC adaptor on a material that is sensitive to heat as the

material could become damaged.

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to any form of strong impact as this can damage the computer’s components or otherwise cause it to malfunction.

Mobile phones

L450/L450D

Please be aware that the use of mobile phones can interfere with the audio system. The operation of the computer will not be impaired in any way, but it is recommended that a minimum distance of 30cm is maintained between the computer and a mobile phone that is in use.

Instruction Manual for Safety and Comfort

All important information on the safe and proper use of this computer is described in the enclosed Instruction Manual for Safety and Comfort. Be sure to read it before using the computer.

User’s Manual xix

L450/L450D

xx User’s Manual

Introduction

This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories.

Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA.

Equipment checklist

Carefully unpack your computer, taking care to save the box and packaging materials for future use.

Hardware

Check to make sure you have all the following items:

■ TOSHIBA L450/L450D Portable Personal Computer

■ AC adaptor and power cord (2-pin plug or 3-pin plug)

L450/L450D

Chapter 1

Documentation

■ L450/L450D User’s Manual

■ L450/L450D Quickstart

■ Instruction Manual for Safety and Comfort (included in User’s Manual)

■ Warranty information

If any of the items are missing or damaged, contact your dealer immediately.

User’s Manual 1-1

L450/L450D

Software

The following Windows® operating system and utility software are pre-installed.

■ Windows 7

■ Display Driver for Windows

■ TOSHIBA Value Added Package

■ TOSHIBA Hardware Setup

■ TOSHIBA Supervisor Password

■ LAN Driver

■ Pointing Device Driver

■ Sound Driver for Windows

■ Wireless LAN Driver (Can be used only for Wireless LAN models)

■ Windows Mobility Center

■ TOSHIBA Face Recognition (is pre-installed on some models)

■ TOSHIBA Disc Creator

■ TOSHIBA Recovery Media Creator

■ TOSHIBA ConfigFree™

■ TOSHIBA SD Memory Utilities

■ TOSHIBA Assist

■ TOSHIBA DVD PLAYER

■ TOSHIBA Web Camera Application (Can be used only for Web Camera

models)

■ TOSHIBA PC Health Monitor

■ TOSHIBA Bulletin Board

■ TOSHIBA ReelTime

■ TOSHIBA Service S tation

■ TOSHIBA eco Utility

■ Online Manual

SD Memory Card Format Utility and other SD functions are packaged into TOSHIBA SD Memory Utilities. When uninstalling the SD utilities, click Start -> Control Panel -> Uninstall a program, and select TOSHIBA SD Memory Utilities.

1-2 User’s Manual

Features

L450/L450D

This computer incorporates the following features and benefits:

Processor

Built-in The processor type varies depending on model.

To check which type of processor is included in your model, open the TOSHIBA PC Diagnostic Tool Utility by clicking Start -> All programs ->

TOSHIBA -> Utilities -> PC Diagnostic Tool.

Chipset Mobile Intel

Mobile Intel

GM45 Express Chipset

GL40 Express Chipset AMD M780V chipset AMD M780G chipset

Memory

Slots PC2-6400 1GB, 2GB or 4GB memory modules

can be installed in the two memory slots. Maximum system memory size and speed are

depending on the model you purchased.

For users of a 32-bit version of Windows: If your computer is configured with two 2 GB memory modules or more, the memory might be displayed as approximately 3 GB only (depending on the computer’s hardware specifications).

This is correct because the operating system usually displays the available memory instead of the physical memory (RAM) built into the computer.

Various system components (like the video adapter’s GPU and PCI devices like Wireless LAN, etc.) requi re th ei r ow n memo ry space. Since a 32-bit operating system cannot address more than 4 GB of memory these system resources overlap the physical memory. It is a technical limitation that the overlapped memory is not available to the operating system.

Even though some tools might display the actual physical memory built into your computer, the memory available to the operating system will still be approximately 3 GB only.

■ Maximum size of memory that can be installed on Mobile Intel® GL40

Express Chipset models is 4 GB.

■ PC2-6400 memory module works as PC2-5300 speed on AMD

Athlon™ 64x2 Dual-Core Processor.

User’s Manual 1-3

L450/L450D

Video RAM Video RAM depends on the model you

purchased. Mobile Intel

Mobile Intel

GM45 Express Chipset model/

GL40 Express Chipset model:

Video RAM capacity shares with main memory, and the proportion depends on Dynamic Video Memory Technology.

AMD M780G Chipset model/ AMD M780V Chipset model:

Video RAM capacity shares with main memory, and the proportion depends on ATI HyperMemory™.

Disks

Hard disk drive or Solid state drive

This computer is equipped with one of the following types of hard disk drives (HDD).

■ 160GB

■ 250GB

■ 320GB

■ 400GB

■ 500GB

Please note that part of the hard disk drive’s overall capacity is reserved as administration space.

Additional hard disk drive sizes may be introduced.

Keyboard

Built-in The internal keyboard provides the embedded

numeric overlay keys, dedicated cursor control overlay keys, and Keys. The keyboard

is compatible with the IBM

enhanced keyboard.

Refer to Chapter 5, The Keyboard, for details.

Pointing Device

Built-in Touch Pad The integrated Touch Pad and control buttons in

the palm rest allow control of the on-screen pointer and support functions such as the scrolling of windows.

1-4 User’s Manual

Power

L450/L450D

Battery pack The computer is powered by one rechargeable

RTC battery The internal RTC battery backs up the Real Time

AC adaptor The AC adaptor provides power to the system

lithium-ion battery pack.

Clock (RTC) and calendar.

and recharges the batteries when they are low. It comes with a detachable power cord which will either have a 2-pin or 3-pin plug enclosure.

As the AC adaptor is universal, it can receive a range of AC voltages from 100 to 240 volts, however you should note that the output current varies among different models. Using the wrong adaptor can damage your computer . Refe r to the

AC adaptor section in Chapter 2, The Grand Tour.

Ports

External monitor This port provides 15-pin, analog VGA port.This

Universal Serial Bus (USB 2.0)

port allows you to connect an external monitor to the computer.

The computer supports multiple Universal Serial Bus ports that comply with the USB 2.0 standard.

Slots

Bridge media This slot lets you insert an SD™/SDHC™

memory card, miniSD™/microSD™ Card, Memory Stick Refer to Chapter 8, Optional Devices.

(PRO™) and MultiMediaCard™.

Multimedia

Sound system The integrated sound system provides support

Web Camera Web Camera is a device that allows you to

User’s Manual 1-5

for the computer’s internal speakers and microphone, also allowing an external microphone and headphones to be connected via the appropriate jacks.

record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger. Camera Assistant Software will help you to add various video effects to your video or photograph.

L450/L450D

HDMI out port HDMI out port can connect with Type A

connector HDMI cable. HDMI cable can send video and audio signals.

Headphone jack This jack lets you connect stereo headphones

Microphone jack A 3.5mm mini microphone jack enables

(16 ohm minimum). When you connect headphones, the internal speakers are automatically disabled.

connection of a three-conductor mini jack for stereo microphone input, and connection of a stereo device for audio input.

Communications

LAN The computer has built-in support for Ethernet

Wireless LAN Some computers in this series are equipped with

■ The transmission speed over the wireless LAN and the distance over

which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configuration s . The Transmit Rate (at X Mbit/s) is the theoretical maximum speed under the IEEE802.11 (a/b/g/n) standards. The actual transmission speed will be lower than the theoretical maximum speed.

LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-TX).

a Wireless LAN module that is compatible with other LAN systems based on Direct Sequence Spread S pectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard.

Security

Security lock slot Connects a security lock to anchor the computer

to a desk or other large object.

1-6 User’s Manual

L450/L450D

Optical disc drive

Your compute r is equipped with a full-size DVD Super Multi drive module that lets you run CDs or DVDs without using an adaptor.

DVD Super Multi drive

The drive reads DVD-ROMs at a maximum 8x speed and CD-ROMs at a maximum 24x speed, and writes CD-Rs at up to 24x speed, CD-RWs at up to 24x speed, DVD-Rs and DVD+Rs at up to 8x speed, DVD-RWs at up to 6x speed, DVD+RWs at up to 8x speed, DVD-R (Dual layer) discs at up to 6x speed, DVD+R (Double Layer) discs at up to 6x speed and DVD-RAM discs at up to 5x speed, and supports the following formats:

■ CD-R

■ CD-RW

■ DVD-ROM

■ DVD-Video

■ CD-DA

■ CD-Text

■ Photo CD™ (single/multi-session)

■ CD-ROM Mode 1, Mode 2

■ CD-ROM XA Mode 2 (Form1, Form2)

■ Enhanced CD (CD-EXTRA)

■ Addressing Method 2

■ DVD-R

■ DVD-R (Dual Layer)

■ DVD-RW

■ DVD+R

■ DVD+R (Double Layer)

■ DVD+RW

■ DVD-RAM

User’s Manual 1-7

L450/L450D

Software

The computer’s internal display panel supports high-resolution video graphics and can be set to a wide range of viewing angles for maximum comfort and readability.

Operating system Windows

Software section at the front of this chapter.

7 is available. Refer to the preinstalled

TOSHIBA Utilities A number of utilities and drivers are preinstalled

Plug and Play When you conn ect an external device to the

Special features

The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use.

Access each function using the following procedures. *1 To access the Power Options, click Start -> Control Panel -> System

and Security -> Power Options.

Hot keys Hot keys are specific key combinations that let

Display automatic power off

HDD automatic power off

System automatic Sleep/Hibernation

Mode

to make your computer more convenient to use. Refer to the Utilities and applications section in this chapter.

computer or when you install a component, Plug and Play capability enables the system to recognize the connection and make the necessary configurations automatically.

you quickly change the system configuration directly from the keyboard without running a system program.

This feature automatically cuts off power to the computer’s display panel when there is no keyboard input for a specified time, with power being restored the next time a key is pressed. This can be specified in the Power Opti ons.

This feature automatically cuts off power to the hard disk drive when it is not accessed for a specified time, with power being restored when the hard disk drive is next accessed. This can be specified in the Power Options.

This feature automatically shuts down the system into either Sleep Mode or Hibernation Mode when there is no input or hardware access for a specified time. This can be specified in the Power Options.

1-8 User’s Manual

L450/L450D

Keypad overlay A ten-key numeric keypad is integrated into the

keyboard. Please refer to the Keypad overlay section in Chapter 5, The Keyboard, for information on using this feature.

Power on password Two levels of password security, supervisor and

user, are available to prevent unauthorized access to your computer.

Instant security A specific hot key function automatically locks the

system providing data security.

Intelligent power supply

A microprocessor in the computer’s intelligent power supply detects the battery’s charge, automatically calculates the remaining battery capacity and protects electronic components from abnormal conditions such as a voltage overload from the AC adaptor. This can be specified in the Power Options.

Battery save mode

This feature lets you configure the computer in order to save battery power. This can be specified in the Power Options.

Low battery automatic Hibernation Mode

When battery power is exhausted to the point that computer operation cannot be continued, the

system automatically enters Hibernation Mode and shuts itself down. This can be specified in the Power Options.

Heat dispersal

T o protect against overheating, the processor has an internal temperature sensor so that, if the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. This can be specified in the Power Options.

If the processor’s temperature reaches an unacceptably high level with either setting, the computer will automatically shuts down to prevent any damage - in this instance all unsaved data in memory will be lost.

Hibernation Mode This feature lets you turn of f the power to the

computer without exiting from your software. The contents of main memory are automatically saved to the hard disk drive so that when you next turn the power on again, you can continue working right where you left off. Refer to the

Turning off the power section in Chapter 3, Getting Started, for more details.

User’s Manual 1-9

L450/L450D

Sleep Mode If you have to interrupt your work, you can use

this feature to allow you to turn off power to the computer without exiting from your software. Data is maintained in the computer’s main memory so that when you next turn on the power, you can continue working right where you left off.

TOSHIBA Value Added Package

This section describes the TOSHIBA Component features pre-installed on the computer.

TOSHIBA Power Saver

TOSHIBA Zooming Utility

TOSHIBA PC Diagnostic Tool

TOSHIBA Flash Cards

TOSHIBA Accessibility

TOSHIBA Power Saver provides you with the features of more various power supply managements.

This utility allows you to enlarge or reduce the icon size on the Windows Desktop, or the zoom factor associated with specific supported applications.

The TOSHIBA PC Diagnostic Tool will display basic system configuration information and allow the functionality of some of the computer’s built-in hardware devices to be tested.

The TOSHIBA Flash Cards provide a quick way to modify selected system functions and to launch applications.

■ Hot key function

■ TOSHIBA utility launcher function

The TOSHIBA Accessibility utility provides support to movement impaired users when they need to use the TOSHIBA Hot-key function s. In use, the utility allows you to make the FN key “sticky”, that is you can press it once, release it, and they press one of the “F” keys in order to access its specific function. When set, the FN key will remain active until another key is pressed.

1-10 User’s Manual

Utilities and Applications

This section describes the pre-installed utilities that come with the computer and details how to start them. For further information on their operation, please refer to each utility’s online manual, help files or README.TXT file.

L450/L450D

TOSHIBA Face Recognition

TOSHIBA Assist T OSHIBA Assist is a graphical user interface that

HW Setup utility T o start the utility, click the Windows Start button,

TOSHIBA ConfigFree

TOSHIBA Disc Creator

TOSHIBA eco Utility TOSHIBA eco Utility helps you monitor your

TOSHIBA Face Recognition uses a face verification library to verify the face data of users when they log in to Windows. If the verification is successful, the user will be logged into Windows automatically. The user can thus avoid having to enter a password or the like, which makes the login process easier.

provides access to specific tools, utilities and applications that make the use and configuration of the computer easier.

point to All Programs, click TOSHIBA, click Utilities, and select HWSetup icon.

TOSHIBA ConfigFree is a suite of utilities that improve the ease and control of communication devices and network connections, help in the identification of communication problems and allow the creation of profiles if you need to switch between different locations and communication networks. To access this utility, click St art -> All Programs -> TOSHIBA -> ConfigFree.

You can create CD’s and DVD’s in a number of formats including audio CD’s that can be played on a standard CD player, and data CD’s/DVD’s which can store copies of the files and folders on your computer’s hard disk drive. This software can be used on models with a DVD Super Multi drive.

To start this utility, click Start -> All Programs ->

TOSHIBA -> CD&DVD Applications -> Disc Creator.

power savings by showing approximate real time power consumption. Furthermore, it shows approximate accumulated power consumption and approximate accumulated power savings when using eco mode daily, weekly, and monthly. Yo u can track power savings by using eco mode continuously.

User’s Manual 1-11

L450/L450D

Windows Mobility Center

This section describes the Windows Mobility Center. Mobility Center is a utility for accessing several mobile PC settings quickly in one window. A default maximum of eight tiles are provided by the operating system, and the additional two tiles are added to your Mobility Center.

■ Lock Computer:

This can be used to lock your computer without turning it off. This has the same function as the Lock button at the bottom of the right pane of the start menu.

■ TOSHIBA Assist:

This can be used to open TOSHIBA Assist if it is already installed in your computer.

TOSHIBA Web Camera Application

TOSHIBA Web Camera Application is pre-configured to start when you turn on Windows 7; if you need to restart it, go to Start ->

All Programs -> TOSHIBA -> Utilities -> Web Camera Application.

TOSHIBA DVD PLAYER

This software is provided for playback of DVD Video. It has an on-screen interface and functions. Click Start -> All Programs -> TOSHIBA DVD PLAYER.

Frame dropping, audio skipping or out of synch audio and video may occur during playback of some DVD Video titles. Make sure to connect the computer’s AC adaptor when playing a DVD Video. Power-saving features may interfere with smooth playback.

1-12 User’s Manual

Options

L450/L450D

You can add a number of options to make your computer even more powerful and convenient to use. The following options are available:

Memory expansion 1GB, 2GB or 4GB memory module (PC2-6400)

can easily be installed in the computer.

Battery Pack An additional battery pack can be purchased for

use as either a spare or replacement. Please refer to Chapter 6, Power and Power-up Modes, for futher information.

AC Adaptor If you frequently use your computer at more than

one site, it may be convenient to purchase an additional AC adaptor to be kept at each site in order to remove the need to always carry the adaptor with you.

USB FDD The USB floppy diskette drive accommodates

either a 1.44MB or 720KB floppy diskette through connection to one of the computer’s USB ports. In use, please be aware that, while you cannot format 720KB floppy diskettes under Windows

7, you are able to read and write to diskettes that have already been formatted.

Security lock A slot is available to attach a security cable to the

computer to deter theft.

User’s Manual 1-13

L450/L450D

1-14 User’s Manual

The Grand Tour

This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer.

Front with the display closed

The following figure shows the computer’s front with its display panel in the closed position.

L450/L450D

Chapter 2

1 2 3 4

1. Bridge media slot

2. Microphone jack

3. Headphone jack

4. Volume control

Figure 2-1 Front of the computer with display closed

Bridge media slot This slot lets you insert an SD™/SDHC™

memory card, miniSD™/microSD™ Card, Memory Stick Refer to Chapter 8, Optional Devices.

Keep foreign metal objects, such as screws, staples and paper clips, out of the Bridge media slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

User’s Manual 2-1

(PRO™) and MultiMediaCard™.

L450/L450D

Left side

Microphone jack A 3.5 mm mini microphone jack enables

connection of a three-conductor mini jack for monaural microphone input, and connection of a stereo device for audio input.

Headphone jack This jack lets you connect a stereo headphone

(16 ohm minimum). When you connect headphones, the internal speaker is automatically disabled.

Volume control Use this dial to adjust the volume of the internal

stereo speakers and optional external stereo headphones (if connected).

Move the Volume control to the left to decrease the volume and to the right to increase the volume.

The following figure shows the computer’s left side.

1 2 3 4 5

1. Cooling vents

2. External monitor port

3. LAN jack

4. HDMI out port

5. Universal Serial Bus (USB 2.0) port

Figure 2-2 The left side of the computer

Cooling vents The cooling vents help keep the processor from

overheating.

Do not block the cooling vents. Keep foreign metal objects, such as screws, staples and paper clips, out of the cooling vents. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

2-2 User’s Manual

L450/L450D

External monitor port

This port allows you to connect an external monitor to the computer.

LAN jack This jack lets you connect to a LAN. The adaptor

has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-TX). The LAN has two indicators. Refer to Chapter 4, Operating Basics, for details.

■ Do not connect any cable other than a LAN cable to the LAN jack.

It could cause damage or malfunction.

■ Do not connect the LAN cable to a power supply. It could cause

damage or malfunction.

HDMI out port HDMI out port can connect with Type A

connector HDMI cable.One HDMI cable can send video and audio signals. (Provided with some models)

Universal Serial Bus (USB 2.0) port

One Universal Serial Bus port, which complies with the USB 2.0 standard, is provided on the left hand side of the computer.

Keep foreign metal objects, such as screws, staples and paper clips, out of the USB connectors. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

Please note that it is not possible to confirm the operation of all functions of all USB devices that are available. In view of this it may be noted that some functions associated with a specific device might not operate properly.

User’s Manual 2-3

L450/L450D

Right side

The following figure shows the computer’s right side.

Back side

1. Universal Serial Bus (USB 2.0) ports

2. Optical disc drive

3. DC IN 19V Jack

4. Security lock slot

Figure 2-3 The right side of the computer

Universal Serial Bus (USB 2.0) ports

Two Universal Serial Bus ports, which comply with the USB 2.0 standard, are provided on the

right side of the computer.

Optical disc drive The computer is configured with a DVD Super

Multi drive.

DC IN 19V Jack The AC adaptor connects to this jack in order to

power the computer and charge its internal batteries. Please note that you should only use the model of AC adaptor supplied with the computer at the time of purchase - using the wrong AC adaptor can cause damage to the computer.

Security lock slot A security cable can be attached to this slot and

then connected to a desk or other large object in order to deter theft of the computer.

The folowing figure shows the computer’s back side.

Figure 2-4 The computer’s back side.

2-4 User’s Manual

Underside

The following figure shows the underside of the computer. You should ensure that the display is closed before the computer is turned over to avoid causing any damage.

1. Battery safety lock

2. Battery pack

3. Battery release latch

4. Cooling vents

5. Memory module slots

6. Hard disk drive

L450/L450D

1 32

Figure 2-5 The underside of the computer

Battery safety lock Slide this latch into its “Unlock” position in order

to release the battery pack and prepare for removal.

Battery pack The battery pack provides power to the computer

when the AC adaptor is not connected. For more detailed information on the use and operation of the battery pack please refer to Chapter 6, Power

and Power-up Modes.

Battery release latch Slide and hold this latch into its “Unlock” position

in order to release the battery pack. For more detailed information on removing the

battery pack please refer to Chapter 6, Power

and Power-up Modes.

User’s Manual 2-5

L450/L450D

Cooling vents The computer’s cooling vents help keep the

processor from overheating.

Memory module slots

The memory module slots are located here. The memory module slots allow for the installation, replacement and removal of additional memory modules. Please refer to the Additional memory

module section in Chapter 8, Optional Devices

for more information.

Hard disk drive The hard disk drive contains the main storage for

the computer. Disk size varies depending on the model purchased.

2-6 User’s Manual

Front with the display open

This section shows the computer with the display panel open. In order to open the display, lift the display panel up and position it at a comfortable viewing angle for you.

L450/L450D

1. Web Camera LED

2. Web Camera

3. Microphone

4. Display screen

5. Display hinge

6. Stereo speakers

7. Touch Pad

8. Touch Pad control buttons

9. Power button

10. System indicators

Figure 2-6 The front of the computer with the display open

Web Camera LED The Web Camera LED glows when the Web

Camera is operating. Please remove the protective plastic-film before

using the Web Camera.

User’s Manual 2-7

L450/L450D

Web Camera The Web Camera is a device that allows you to

record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger. TOSHIBA Web Camera Application will help you to add various video effects to your video or photograph.

The web camera also enables the transmission of video and use of video chat via the internet using specialized applications. The effective pixel count for this web camera is 0.3 million or

1.0 million (0.3M maximum photograph size: 640X480 pixels; 1.0M maximum photograph size: 1280X800 pixels).

Please remove the protective plastic-film before using the Web Camera.

Please refer to the Using the web camera section in Chapter 4, Operating Basics. Some models are equipped with a Web Camera.

Microphone A built-in microphone allows you to import and

record sounds for your application - please refer to the Sound system section in Chapter 4,

Operating Basics for more information.

Display screen Please be aware that, when the computer is

operating on the AC adaptor, the image displayed on the internal screen will be somewhat brighter than when it operates on battery power. This difference in brightness levels is intended to save power when operating on batteries. For more information on the computer’s display, please refer to the Display

Controller section in Appendix B.

Display hinge The display hinge allows the display panel to be

position at a variety of easy-to-view angles.

Stereo speakers The speakers emit sound generated by your

software as well as audio alarms, such as low battery condition, generated by the system.

Keep foreign objects out of the speakers. Never allow metal objects, such as screws, staples and paper clips, to enter the computer or keyboard. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.

2-8 User’s Manual

L450/L450D

To uc h Pa d The Touch Pad mouse control device located in

the center of the palm rest is used to control the movement of the on-screen pointer. For more information, please refer to the Using the Touch

Pad section in Chapter 4, Operating Basics.

To uc h Pa d co ntrol buttons

The control buttons located below the T ouch Pad allow you to select menu items or manipulate text and graphics as designated by the on-screen pointer.

Power button Press this button to t urn the computer’s power on

and off.

System indicators These LED indicators allow you to monitor the

status of various computer functions and are described in more detail within the System

indicators section.

User’s Manual 2-9

L450/L450D

System indicators

The LED system indicators for specific computer operations glow when those operations are in progress.

Figure 2-7 System indicators

Wireless communication

DC IN The DC IN indicator normally glows white when

Power The Power indicator normally glows white when

Battery The Battery indicator shows the condition of the

HDD/ODD The HDD/ODD indicator glows white whenever

Bridge media slot The Bridge media slot indicator glows white

The Wireless communication indicator glows amber when the Wireless LAN functions are turned on.

power is being correctly supplied from the AC power adaptor. However, If the output voltage from the adaptor is abnormal, or if the computer’s power supply malfunctions, this indicator will go out.

the computer is turned on. However, if you turn the computer off into Sleep Mode, this indicator will flash amber - approximately one second on, two seconds off - both while the system is shutting down and while it remains turned off.

battery’s charge - white indicates the battery is fully charged, amber indicates the battery is charging, and flashing amber indicates a low battery condition. Please refer to Chapter 6,

Power and Power-up Modes for more information

on this feature.

the computer is accessing the built-in hard disk drive or the other drives.

when the computer is accessing the Bridge media slot.

2-10 User’s Manual

Keyboard indicators

The following figures show the positions of the CAPS LOCK indicator and the keypad overlay indicators which show the following conditions:

■ When the CAPS LOCK indicator glows, the keyboard will produce

capitals when any letter is typed.

■ When the Arrow Mode indicator glows, the keypad overlay allows you to

use cursor functions.

■ When the Numeric Mode indicator glows, the keypad overlay allows

you to enter numbers.

L450/L450D

Figure 2-8 Keypad indicators

CAPS LOCK This indicator glows green when letter keys are

locked into their uppercase format.

User’s Manual 2-11

L450/L450D

Optical disc drive

The computer is configured with a DVD Super Multi drive. A Serial ATA interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. For further information on loading and unloading discs, please refer to the Writing CD/DVD on DVD Super Multi drive section in Chapter 4, Operating

Basics.

Region codes for DVD drives and media

DVD Super Multi drives and their associated media are manufactured according to the specifications of six marketing regions. When you purchase DVD-Video, make sure it matches your drive, otherwise it will not play properly.

Code Region

1 Canada, United S tates 2 Japan, Europe, South Africa, Middle East 3 South East Asia, East Asia 4 Australia, New Zealand, Pacific Islands, Central America,

5 Russia, Indian Subcontinent, Africa, North Korea,

6 China

South America, Caribbean

Mongolia

Writable discs

This section describes the types of writable CD/DVD discs. Check the specifications of your drive to see the types of discs it can write. Use TOSHIBA Disc Creator to write compact discs. Please refer to Chapter 4,

Operating Basics for further information.

CDs

■ CD-R discs can be written only once. The recorded data cannot be

erased or changed.

■ CD-RW discs including multi speed CD-RW discs, high-speed CD-RW

discs and ultra-speed CD-RW discs can be recorded more than once.

2-12 User’s Manual

DVDs

■ DVD-R, DVD+R, DVD-R (Dual Layer) and DVD+R (Double Layer) discs

can be written only once. The recorded data cannot be erased or changed.

■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than

once.

Some types and formats of DVD-R (Dual Layer) and DVD+R (Double Layer) discs may be unreadable.

DVD Super Multi drive

The full-size DVD Super Multi drive module allows you to record data to recordable CDs and DVDs as well as run either 12cm (4.72") CDs, and DVDs, and 8cm (3.15") CDs and DVDs without using an adaptor.

The speed is slower at the center of a disc and faster at the outer edge.

DVD read 8 speed (maximum) DVD-R write 8 speed (maximum) DVD-R DL write 6 speed (maximum) DVD-RW write 6 speed (maximum) DVD+R write 8 speed (maximum) DVD+R DL write 6 speed (maximum) DVD+RW write 8 speed (maximum) DVD-RAM write 5 speed (maximum) CD read 24 speed (maximum) CD-R write 24 speed (maximum) CD-RW write 24 speed (maximum, Ultra-speed media)

L450/L450D

User’s Manual 2-13

L450/L450D

AC adaptor

The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost any country/region. The adaptor converts AC power to DC power and reduces the voltage supplied to this computer.

To recharge the battery, simply connect the AC adaptor to a power source and to the computer. Please refer to Chapter 6, Power and Power-up

Modes for further information.

Figure 2-9 The AC adaptor (2-pin plug)

Figure 2-10 The AC adaptor (3-pin plug)

■ Depending on the model in question, either a 2-pin or 3-pin

adaptor/power lead will be bundled with the computer.

■ Do not use a 3-pin to 2-pin conversion plug.

■ The supplied power cord conforms to safety rules and regulations in

the region the product is bought and should not be used outside of this region. In order to use the adaptor/computer in other regions, you should please buy a power cord that conforms to the safety rules and regulations in that particular region.

Always use the TOSHIBA AC adaptor that was included with your computer, or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury.

2-14 User’s Manual

Getting Started

This chapter provides basic information to start using your computer. It covers the following topics:

■ If the battery pack is not pre-installed in the computer that you

purchased, please install the battery pack before you start using the computer. Please refer to Chapter 6, Replacing the battery pack, for further information about installing the battery pack.

■ All users should be sure to read the section Starting up f or the first time.

■ Be sure to read the enclosed Instruction Manual for Safety and Comfort

for information on the safe and proper use of this computer. It is intended to help you be more comfortable and productive while using a notebook computer. By following the recommendations in it you may reduce your chance of developing a painful or disabling injury to your hand, arms, shoulders or neck.

L450/L450D

Chapter 3

■ Connecting the AC adaptor

■ Opening the display

■ Turning on the power

■ Starting up for the first time

■ Turning off the power

■ Restarting the computer

■ System Recovery Options and Restoring the pre-installed software

■ Use an anti-virus software and update it regularly.

■ Never format storage media without checking its content - formatting

destroys all stored data.

■ It is a good idea to periodically back up the internal hard disk drive or

other main storage device to external media. General storage media is not durable or stable over long periods of time and under certain conditions may result in data loss.

■ Before you install a device or application, save any data in memory to

the hard disk drive or other storage media. Failure to do so may result in the loss of data.

User’s Manual 3-1

L450/L450D

Connecting the AC adaptor

Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power.

The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-up Modes.

■ Always use the TOSHIBA AC adaptor that was included with your

computer or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor.

■ Never plug the AC adaptor into a power source that does not

correspond to both the voltage and the frequency specified on the regulatory label of the unit. Failure to do so could result in a fire or electric shock, possibly resulting in serious injury.

■ Always use or purchase power cables that comply with the legal

voltage and frequency specifications and requirements in the country of use. Failure to do so could result in a fire or electric shock, possibly resulting in serious injury.

■ The supplied power cord conforms to safety rules and regulations in

the region from which the product is purchased and should not be used outside this region. For use in other regions, please buy power cords that conform to safety rules and regulations in that particular region.

■ Do not use a 3-pin to 2-pin conversion plug.

■ When you connect the AC adaptor to the computer, always follow the

steps in the exact order as described in the User’s Manual. Connecting the power cable to a live electrical outlet should be the last step otherwise the adaptor DC output plug could hold an electrical charge and cause an electrical shock or minor bodily injury when touched. As a general safety precaution, avoid touching any metal parts.

■ Never place your computer or AC adaptor on a wooden surface,

furniture, or any other surface that could be marred by exposure to heat since the computer base and AC adaptor’s surface increase in temperature during normal use.

■ Always place your computer or AC adaptor on a flat and hard surface

that is resistant to heat damage.

Refer to the enclosed Instruction Manual for Safety and Comfort for detailed precautions and handling instructions.

3-2 User’s Manual

L450/L450D

1. Connect the power cord to the AC adaptor.

Figure 3-1 Connecting the power cord to the AC adaptor (2-pin plug)

Figure 3-2 Connecting the power cord to the AC adaptor (3-pin plug)

Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model.

2. Connect the AC adaptor’s DC output plug to the DC IN 19V jack on the right side of the computer.

Figure 3-3 Connecting the adaptor to the computer

3. Plug the power cord into a live wall outlet - the Battery and DC IN indicators on the front of the computer should glow.

User’s Manual 3-3

L450/L450D

Opening the display

The display panel can be opened to a wide range of angles for optimal viewing.

While holding down the palm rest with one hand so that the main body of the computer is not raised, slowly lift the display panel - this will allow the angle of the display panel to be adjusted to provide optimum clarity.

Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer.

Figure 3-4 Opening the display

■ As the display panel cannot be flipped to 180 degrees, please be

careful of the angle when flipping open the display panel.

■ Be careful not to open the display panel too far as this could put stress

on the display panel’s hinges and cause damage.

■ Do not press or push on the display panel.

■ Do not lift the computer by the display panel.

■ Do not close the display panel with pens or any other objects left in

between the display panel and the keyboard.

■ When opening or closing the display panel, place one hand on the

palm rest to hold the computer in place and use the other hand to slowly open or close the display panel (Do not use excessive force when opening or closing the display panel).

3-4 User’s Manual

Turning on the power

This section describes how to turn on the power - the Power indicator will then indicate the status. Please refer to the Monitoring of power condition section in Chapter 6, Power and Power-up Modes, for more information.

■ After you turn on the power for the first time, do not turn it off until you

have set up the operating system. Please refer to the section Starting

up for the first time for more information.

■ Volume cannot be adjusted during Windows Setup.

1. Open the computer’s display panel.

2. Press the computer’s power button.

L450/L450D

Figure 3-5 Turning on the power

Starting up for the first time

The Windows 7 Startup Screen will be the first screen displayed when you turn on the power. Follow the on-screen instructions on each screen in order to properly install the operating system.

When it is displayed, be sure to read the Software License Terms carefully.

User’s Manual 3-5

L450/L450D

Turning off the power

The power can be turned off in one of three modes, either Shut Down Mode, Hibernation Mode or Sleep Mode.

Shut Down Mode

When you turn off the power in Shut Down Mode no data will be saved and the computer will boot to the operating system’s main screen the next time it is turned on.

1. If you have entered data, either save it to the hard disk drive or to other storage media.

2. Make sure all disk/disc activity has stopped before removing the CD/DVD or floppy diskette.

■ Make sure the Hard Disk Drive indicator is off. If you turn off the power

while a disk (disc) is being accessed, you may lose data or damage the disk.

■ Never turn off the power while an application is running. Doing so could

cause loss of data.

■ Never turn off the power, disconnect an external storage device or

remove storage media during data read/write. Doing so can cause data loss.

3. Click Start.

4. Click the Shut down button ( ).

5. Turn off any peripheral devices connected to your computer.

Do not turn the computer or peripheral devices back on immediately - wait a short period to avoid any potential damage.

Hibernation Mode

The Hibernation Mode feature saves the contents of memory to the hard disk drive when the computer is turned off so that, the next time it is turned on, the previous state is restored. Please note that the Hibernation Mode feature does not save the status of any peripheral devices connected to the computer.

■ Save your data. While entering Hibernation Mode, the computer saves

the contents of memory to the hard disk drive. However, for safety sake, it is best to save your data manually.

■ Data will be lost if you remove the battery or disconnect the AC adaptor

before the save is completed. Wait for the Hard Disk Drive indicator to go out.

■ Do not install or remove a memory module while the computer is in

Hibernation Mode. Data will be lost.

3-6 User’s Manual

L450/L450D

Benefits of Hibernation Mode

The Hibernation Mode feature pro vi des the following benefits:

■ Saves data to the hard disk drive when the computer automatically

shuts down because of a low battery condition.

■ Y ou can return to your previous working environment immediately when

you turn on the computer.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the time period set by the System Hibernate feature.

■ Allows the use of the panel power off feature.

Starting Hibernation Mode

You can also enable Hibernation Mode by pressing FN + F4 - please refer to Chapter 5, The Keyboard, for further details.

To enter Hibernation Mode, follow the steps below.

1. Click St art.

2. Click the arrow ( ) in the power management button ( ) and select Hibernate from the menu.

Automatic Hibernation Mode

The computer can be configured to enter Hibernation Mode automatically when you press the power button or close the lid. In order to define these settings, you can follow the steps as described below:

1. Click St art and click the Control Panel.

2. Click System and Security and click Power Options.

3. Click Choose what the power button does or Choose what closing the lid does.

4. Enable the desired Hibernation Mode settings for When I press the power button and When I close the lid.

5. Click the Save changes button.

Data save in Hibernation Mode

When you turn off the power in Hibernation Mode, the computer will take a moment to save the current data in memory to the hard disk drive. During this time, the Hard Disk Drive indicator will glow.

After you turn off the computer , and the content of memory has been saved to the hard disk drive, turn off the power to any peripheral devices.

Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.

User’s Manual 3-7

L450/L450D

Sleep Mode

If you have to interrupt your work, you are able to turn off the power without exiting from your software by placing the computer into Sleep Mode. In this mode data is maintained in the computer’s main memory so that when you turn on the power again, you can continue working right where you left off.

When you have to turn off your computer aboard an aircraft or in places where electronic devices are regulated or controlled, always completely shut down the computer. This includes turning off any wireless communication switches or devices, and canceling settings that reactivate the computer automatically, such as a timer recording function. Failure to completely shut down the computer in this way could allow the operating system to reactivate and run pre-programmed tasks or preserve unsaved data, which could interfere with aviation or other systems, possibly causing serious injury.

■ Before entering Sleep Mode, be sure to save your data.

■ Do not install or remove a memory module while the computer is in

Sleep Mode. The computer or the memory module could be damaged.

■ Do not remove the battery pack while the computer is in Sleep Mode

(unless the computer is connected to an AC power source). Data in memory could be lost.

■ When the AC adaptor is connected, the computer will go into Sleep Mode

according to the settings in the Power Options (to access it, Start -> Control Panel -> System and Sec urity -> Power Options).

■ To restore the operati on of the computer from Sleep Mode, press and

hold the power button or any key on the keyboard for a short amount of time. Please note that keyboard keys can only be used if the Wake-up on Keyboard option is enabled within the HW Setup utility.

■ If the computer enters Sleep Mode while a network application is

active, the application might not be restored when the computer is next turned on and the system returns from Sleep Mode.

■ To prevent the computer from automatically entering Sleep Mode,

disable Sleep Mode within the Power Options (to access it, Start -> Control Panel -> System and Security -> Power Options).

■ To use the Hybrid Sleep function, configure it in the Power Options.

Benefits of Sleep Mode

The Sleep Mode feature provides the following benefits:

■ Restores the previous working environment more rapidly than does the

Hibernation Mode feature.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the time period set by the System Sleep Mode feature.

■ Allows the use of the panel power off feature.

3-8 User’s Manual

L450/L450D

Executing Sleep Mode

You can also enable Sleep Mode by pressing FN + F3 - please refer to Chapter 5, The Keyboard, for further details.

You can enter Sleep Mode in one of three ways:

■ Click Start then click the arrow ( ) in the power management button

( ) and select Sleep from the menu.

■ Close the display panel. Please note that this feature must be enabled

within the Power Options (to access it, click Start -> Control Panel -> System and Security -> Power Options).

■ Press the power button. Please note that this feature must be enabled

within the Power Options (to access it, click Start -> Control Panel -> System and Security -> Power Options).

When you turn the power back on, you can continue where you left when you shut down the computer.

■ When the computer is in Sleep Mode, the Power indicator will blink

amber.

■ If you are operating the computer on battery power, you can lengthen

the overall operating time by turning it off into Hibernation Mode - Sleep Mode will consume more power while the computer is off.

Sleep Mode limitations

Sleep Mode will not function under the following conditions:

■ Power is turned back on immediately after shutting down.

■ Memory circuits are exposed to static electricity or electrical noise.

Restarting the computer

Certain conditions require that you reset the computer, for example if:

■ Yo u change certain computer settings.

■ An error occurs and the computer does not respond to your keyboard

commands.

If you need to restart the computer, there are three ways this can be achieved:

■ Click Start then click the arrow ( ) in the power management button

( ) and select Restart from the menu.

■ Press CTRL, ALT and DEL simultaneously (once) to display the menu

window, then select Restart from the Shut down options.

■ Press the power button and hold it down for four seconds. Once the

computer has turned itself off, wait between ten and fifteen seconds before turning the power on again by pressing the power button.

User’s Manual 3-9

L450/L450D

System Recovery Options

A hidden partition is allocated on the hard disk drive for the System Recovery Options.

This partition stores files which can be used to repair the system in the event of a problem.

The System Recovery Options feature will be unusable if this partition is deleted.

System Recovery Options

The System Recovery Options feature is installed on the hard disk when shipped from the factory. The System Recovery Options menu includes tools to repair startup problems, run diagnostics or restore the system.

See the Windows Help and Support content for more information about Startup Repair.

The System Recovery Options can also be run manually to repair problems.

The procedure is as follows. Follow the instructions shown on the on-screen menu.

1. Turn off the computer.

2. While holding the F8 key, turn on the computer.

3. The Advanced Boot Options menu will be displayed. Use the arrow keys to select Repair Your Computer and press ENTER.

4. Follow the on-screen instructions.

The Windows 7 CompletePC Backup feature can be used on Windows® 7 Professional and Windows

7 Ultimate.

Restoring the pre-installed Software

Depending on the model you purchased, different ways for restoring the pre-installed software are offered:

■ Creating optical Recovery Discs and restoring the pre-installed software

from them

■ Restoring the pre-installed software from the Recovery hard disk drive

■ Ordering Recovery Discs from TOSHIBA and restoring the pre-installed

software from them*

* Please note that this service is not free-of-charge.

3-10 User’s Manual

L450/L450D

Creating Optical Recovery Discs

This section describes how to create Recovery Discs.

■ Be sure to connect the AC adaptor when you create Recovery Discs.

■ Be sure to close all other software programs except the TOSHIBA

Recovery Media Creator.

■ Do not run software such as screen savers which can put a heavy load

on the CPU.

■ Operate the computer at full power.

■ Do not use power-saving features.

■ Do not write to the disc when the anti-virus software is running. Wait for

it to finish, then disable virus detection programs including any software that checks files automatically in the background.

■ Do not use utilities, including those intended to enhance hard disk drive

access speed. They may cause unstable operation and damage data.

■ Do not shut down/log off or Sleep/Hibernate while writing or rewriting

the disc.

■ Set the computer on a level surface and avoid places subjected to

vibrations such as airplanes, trains, or cars.

■ Do not use on unstable tables or other any other unstable surfaces.

A recovery image of the software on your computer is stored on the hard disk drive, and can be copied to DVD media by using the following steps:

1. Have a blank DVD media ready.

2. The application will allow you to choose from a variety of different media

onto which the recovery image can be copied including DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL and DVD+RW.

Please note that some of the above media may not be compatible with the optical disc drive installed into your computer. You should therefore verify the optical disc drive supports the blank media you have chosen before proceeding.

3. Turn on your computer and allow it to load the Windows 7 operating

system from the hard disk drive as normal.

4. Insert the first blank media into the optical disc drive tray .

5. Select the TO SHIBA Recovery Media Creator icon from the Windows

7 Start menu.

6. Af ter TOSHIBA Recovery Media Creator starts, select the type of media

and the title you wish to copy, and then click the Create button.

User’s Manual 3-11

L450/L450D

Restoring the pre-installed software from your created Recovery Discs

If the pre-installed files are damaged, you are able to either use the Recovery Discs you have created to restore the computer to the state it was in when you originally received it. T o perform this restoration, follow the steps below:

When the sound mute feature has been activated by pressing the FN + ESC key, be sure to disable this to allow sounds to be heard before starting the restore process. Please refer to Chapter 5, The Keyboard, for further details.

You can not use System Recovery Options if restoring the pre-in stalled software without System Recovery Options.

When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost.

1. Load the (1st disc of) Recovery Discs into the optical disc drive and turn off the computer’s power.

2. While holding down F12 key on the keyboard, turn on your comput er when TOSHIBA Leading Innovation>>> appears, release the F12 key.

3. Use the up and down cursor keys to select the CD-ROM icon from the menu.

4. A menu will be displayed from which you should follow the on-screen instructions.

Restoring the pre-installed software from the Recovery hard disk drive

A portion of the total hard disk drive space is configured as a hidden recovery partition. This partition stores files which can be used to restore pre-installed software in the event of a problem.

If you subsequently set up your hard disk drive again, do not change, delete or add partitions in a manner other than specified in the manual, otherwise you may find that space for the required software is not available.

In addition, if you use a third-party partitioning program to reconfigure the partitions on your hard disk drive, you may find that it becomes impossible to setup your computer.

When the sound mute feature has been activated by pressing the Mute panel (Fn+ESC), be sure to disable this to allow sounds to be heard before starting the restore process. Please refer to Chapter 5, The Keyboard, for further details.

You can not use System Recovery Options if restoring the pre-in stalled software without System Recovery Options.

3-12 User’s Manual

L450/L450D

When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost.

1. Turn off your computer.

2. While holding down 0 (zero) key on the keyboard, turn on your

computer.

A menu will be displayed from which you should follow the on-screen instructions.

Please set your BIOS to default before you recover your computer to the factory state!

Ordering Recovery Discs from TOSHIBA*

You can order Product Recovery discs for your notebook from the TOSHIBA Europe Backup Media Online Shop.

* Please note that this service is not free-of-charge.

1. Visit https://backupmedia.toshiba.eu on the Internet.

2. Follow the on-screen instructions. You will receive your Recovery Discs within two weeks after placing your

order.

User’s Manual 3-13

L450/L450D

3-14 User’s Manual

Operating Basics

This chapter describes the basic operations of your computer and highlights the precautions that should be taken when using it.

Using the Touch Pad

To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.

L450/L450D

Chapter 4

1 2

1. Touch Pad

2. Touch Pad control buttons

Figure 4-1 Touch Pad and Touch Pad control buttons

The two buttons below the Touch Pad are used like the butt o ns on a standard mouse - press the left button to select a menu item or to manipulate text or graphics designated by the pointer, and press the right button to display a menu or other function depending on the software you are using.

You can also tap the Touch Pad to perform functions similar to those of the left button on a standard mouse.

Click: Tap once Double-click: T ap twice Drag and drop: Tap to select the item(s) you want to move, leave your

finger on the T ouch Pad after the second tap and then move the item(s) to their new destination.

User’s Manual 4-1

L450/L450D

Using the optical disk drive

The full-size drive provides high-performance execution of CD/DVD-ROMbased programs. Yo u can run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an adaptor. A Serial ATA interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD-ROM, an indicator on the drive glows.

Use the Toshiba DVD Player application to view DVD-Video discs.

Loading discs

To load CD/DVD’s, follow the steps as listed below and refer to figures 4-4 to 4-6.

1. When the computer’s power is on, press the eject button to open the disc tray slightly.

1. Disc tray LED

2. Eject button

3. Eject hole

21 3

Figure 4-2 Pressing the eject button

2. Grasp the disc tray gently and pull until it is fully opened.

Figure 4-3 Pulling the disc tray open

4-2 User’s Manual

L450/L450D

3. Lay the CD/DVD, label side up, in the disc tray.

Figure 4-4 Inserting a CD/DVD

When the disc tray is fully opened, the edge of the computer will extend slightly over the area where you insert the media. Therefore, when loading a CD or DVD, you will need to turn it slightly at an angle when you place it in the disc tray. After loading the CD/DVD you should ensure that it is properly positioned over the central spindle and that it lies flat within the tray.

■ Do not touch either the laser lens or the area immediately around it -

doing so could cause misalignment and may damage the drive.

■ Make sure that no foreign objects are inserted into or otherwise enter

the drive. Check the disc tray, especially the area behind the front edge, to ensure that there are no foreign objects or material present before closing the drive.

4. Press the center of the CD/DVD gently until you feel it click into place

on the center spindle. The disc should be slightly below the top of the spindle and flush with the spindle base.

5. Press the center of the disc tray in order to close it - the tray will click

into place when it is locked.

If the CD/DVD is not seated properly when the disc tray is closed, you may find that the media itself might become damaged, and/or the disc tray might not open fully when you next press the eject button.

User’s Manual 4-3

L450/L450D

Removing discs

To remove CD/DVDs, follow the steps as listed below.

Do not press the eject button while the computer is accessing the media in the drive, instead wait for the indicator to go out before you open the disc tray. In addition, if the CD/DVD media is spinning when you open the tray , wait for it to fully stop before you remove it.

1. When the computer’s power is on, press the eject button to open the disc tray slightly and then gently pull it out of the system until it is fully opened.

After the disc tray has opened slightly, you should wait for a moment to ensure the CD/DVD media has stopped spinning before you fully open the tray.

2. The CD/DVD media will extend slightly over the sides of the disc tray in order that you can hold it. Grasp it carefully by its edges and lift it vertically off of the central spindle and out of the tray.

Figure 4-5 Removing a CD/DVD

3. Press the center of the disc tray in order to close it - the tray will click into place when it is locked.

4-4 User’s Manual

How to remove a CD/DVD when the disc tray will not o p en

Pressing the eject button will not open the disc tray when the computer is turned off although, in these circumstances, you can open the tray by inserting a slender object such as a straightened paper clip about 15mm into the eject hole just to the right of the drive’s eject button.

L450/L450D

1. Disc tray LED

2. Eject button

3. Eject hole

Figure 4-6 Manual release with the eject hole

You must ensure that you turn off the power before you use the eject hole. If the CD/DVD media is spinning when you open the disc tray, it may fly off of the spindle and cause injury.

Writing CD/DVD on DVD Super Multi drive

The optical drive installed on this computer cannot write multiple sessions on DVD-R Dual Layer disc sessions. Once a disc has been written to once, it will be finalized. Once finalized, no further writing to the disc will be possible regardless of what portion of the total disc capacity was used.

You can use the DVD Super Multi drive to write data to either CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW, DVD-RAM, or DVD-R (Dual Layer) discs.

TOSHIBA Disc Creator can be used to write data.

■ Please refer to the section Writable discs, Chapter 2 for details about

the types of writable CD and DVD discs that can be supported by this computer.

■ Do not turn off the power to the optical disc drive while the computer is

accessing it as this may cause you to lose data.

■ CD-R/RW media cannot be accessed using the Create CD/DVD option

in Media Center.

■ To write data to CD-R/-RW media, use the TOSHIBA Disc Creator

feature that is installed on your computer.

21 3

User’s Manual 4-5

L450/L450D

When writing information to media using an optical drive, you should always ensure that you connect the AC adaptor to a live power socket. It is possible that, if data is written while powered by the battery pack, the write process may sometimes fail due to low battery power - in these instances data loss may occur.

Important message

Before you write or rewrite to any of the media supported by the DVD Super Multi drive, please read and follow all of the setup and operating instructions in this section. If you fail to do so, you may find that the DVD Super Multi drive drive may not function properly, and you may fail to write or rewrite information successfully - this may cause you to either lose data or incur other damage to the drive or media.

Before writing or rewriting

■ Based on TOSHIBA’s limited compatibility testing, we suggest the

following manufacturers of CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW or DVD-RAM media, however, it must be noted that disc quality can affect write or rewrite success rates. Please also be aware that in no event does TOSHIBA guarantee the operation, quality or performance of any disc.

CD-R:

TAI Y O YUDE N CO., Ltd. MITSUBISHI KAGAKU MEDIA CO., LTD. Hitachi Maxell,Ltd.

CD-RW: (Multi-Speed and High-Speed)

MITSUBISHI KAGAKU MEDIA CO., LTD.

CD-RW: (Ultra-Speed)

MITSUBISHI KAGAKU MEDIA CO., LTD.

DVD-R:

DVD Specifications for Recordable Disc for General Version 2.0

TAIYO YUDEN Co.,Ltd. (for 8x and 16x speed media) MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x, 8x and 16x speed media) Hitachi Maxell,Ltd. (for 8x and 16x speed media)

DVD-R (Dual Layer):

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x and 8x speed media)

DVD-R for Labelflash:

FUJIFILM CORPORATION (for 16x speed media)

4-6 User’s Manual

L450/L450D

DVD+R:

MITSUBISHI KAGAKU MEDIA CO., L TD. (for 8x and 16x speed media) TAIYO YUDEN CO., Ltd. (for 8x and 16x speed media)

DVD+R (Double Layer):

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2.4x and 8x speed media)

DVD+R for Labelflash:

FUJIFILM CORPORATION (for 16x speed media)

DVD-RW:

DVD Specifications for Recordable Disc for Version 1.1 or version 1.2 Victor Company of Japan, Ltd. (JVC) (for 2x, 4x and 6x speed media) MITSUBISHI KAGAKU MEDIA CO., LTD.

(for 2x, 4x and 6x speed media)

DVD+RW:

MITSUBISHI KAGAKU MEDIA CO., L TD. (for 2.4x, 4x and 8x speed media)

DVD-RAM:

DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2

Panasonic Electric Industrial Co.,Ltd. (for 3x and 5x speed media) Hitachi Maxell,Ltd. (for 3x and 5x speed media)

■ DVD Super Multi drive cannot use discs that allow writing faster than

16x speed (DVD-R and DVD+R media), 8x speed (DVD-R (Dual Layer), DVD+RW and DVD+R (Double Layer) media), 6x speed (DVD-RW media), 5x speed (DVD-RAM media).

■ Some types and formats of DVD-R (Dual Layer) and DVD+R (Double

Layer) discs may be unreadable.

■ 2.6GB and 5.2GB DVD-RAM media cannot be read from or written to.

■ Discs created in DVD-R (Dual Layer) format4 (Layer Jump Recording)

cannot be read.

■ If the disc is poor in quality, or is dirty or damaged, writing or rewriting

errors may be noted - ensure that you check all discs for dirt or damage before you use them.

■ The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or

DVD-RAM media will be affected by the quality of the disc itself and the way in which it is used.

■ There are two types of DVD-R media available, authoring discs and

general use discs. Do not attempt to use authoring discs as only general use discs can be written to by a computer drive.

User’s Manual 4-7

L450/L450D

■ Y ou can use both DVD-RAM discs that can be removed from a cartridge

and DVD-RAM discs designed without a cartridge.

■ You may find that other computer DVD-ROM drives or other DVD

players may not be able to read DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer) or DVD+RW discs.

■ Data written to a CD-R, DVD-R, DVD-R (Dual Layer), DVD+R or

DVD+R (Double Layer) discs cannot be deleted either in whole or in part.

■ Data deleted/erased from a CD-RW, DVD-RW, DVD+RW or DVD-RAM

disc cannot be recovered. You must check the content of the disc carefully before you delete it, taking care that, if multiple drives that can write data to discs are connected, you do not delete data from the wrong one.

■ In writing to DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R

(Double Layer), DVD+RW or DVD-RAM media, some space is required for file management, so you may not be able to write to the full capacity of the disc.

■ Since the disc is based on the DVD standard, it might be filled with

dummy data if the written data is less than about 1GB. Therefore, in these circumstance, even if you write only a small amount of data, it might take additional time to fill in the dummy data.

■ When multiple drives that can write data to discs are connected, be

sure that you do not write to or delete data from the wrong drive.

■ Be sure to connect the AC adaptor to the computer before you write or

rewrite any information.

■ Before you enter either Sleep Mode or Hibernation Mode, take care to

ensure that any DVD-RAM writing has been completed. In this instance, writing is finished if you can eject the DVD-RAM media.

■ Be sure to close all other software programs except for the writing

software itself.

■ Do not run software such as a screen saver which can put a heavy load

on the processor.

■ Operate the computer at its full power settings - do not use any

power-saving features.

■ Do not write information while virus checking software is running,

instead wait for it to finish, then disable the virus protection applications, including any software that checks files automatically in the background.

■ Do not use any hard disk utilities, including those that are intended to

enhance hard disk drive access speeds, as they may cause unstable operation and damage data.

■ CD-RW (Ultra Speed +) media should not be used as data may be lost

or damaged.

■ You should always write from the computer’s hard disk drive onto the

CD/DVD - do not try to write from shared devices such as a server or any other network device.

4-8 User’s Manual

■ Writing with software other than TOSHIBA Disc Creator has not been

confirmed, therefore operation with other software applications cannot be guaranteed.

When writing or rew riting

Please observe the following points while you write or rewrite data to CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW or DVD-RAM media:

■ Always copy data from the hard disk drive to the optical media - do not

use the cut-and-paste function as the original data will be lost if there is a write error.

■ Do not perform any of the following actions:

■ Change users in the Windows® 7 operating system.

■ Operate the computer for any other function, including such tasks as

using a mouse or Touch Pad, or closing/opening the display panel.

■ Start a communication application such as a modem.

■ Apply impact or vibration to the computer.

■ Install, remove or connect external devices, including such items as

a SD/SDHC memory card, miniSD/microSD Card, Memory Stick/ Memory Stick PRO, MultiMediaCard, USB device, external monitor, or an optical digital device.

■ Open the optical disc drive.

■ Do not use shut down, log off, Sleep Mode or Hibernation Mode

functions while writing or rewriting.

■ Make sure that the write/rewrite operation is completed before going

into either Sleep Mode or Hibernation Mode (writing is completed if you can remove an optical media on the DVD Super Multi drive).

■ If the media is of poor quality, or is dirty or damaged, writing or rewriting

errors may occur.

■ Set the computer on a level surface and avoid places subject to

vibration such as airplanes, trains or cars. In addition, do not use the computer on an unstable surface such as a stand.

■ Keep mobile phones and other wireless communication devices away

from the computer.

L450/L450D

User’s Manual 4-9

L450/L450D

Disclaimer

TOSHIBA does not bear responsibility for the following:

■ Damage to any CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW,

■ Any change or loss of the recorded contents of CD-R, CD-RW, DVD-R,

■ Damage that may be caused by using third party equipment or

Given the technological limitations of current optical disc writing drives, you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices. In view of this, it is good practice to make two or more copies of important data, in case of any undesired change or loss of the recorded contents.

TOSHIBA Disc Creator

Please be aware of the following limitations when you use the TOSHIBA Disc Creator:

■ DVD Video cannot be created using TOSHIBA Disc Creator.

■ DVD Audio cannot be created using TOSHIBA Disc Creator.

■ You cannot use TOSHIBA Disc Creator’s “Audio CD for Car or Home

■ Do not use the “Disc Backup” function of TOSHIBA Disc Creator in

■ DVD-RAM discs cannot be backed up using the “Disc Backup” function

■ You cannot back up CD-ROM, CD-R or CD-RW media to DVD-R,

■ You cannot back up CD-ROM, CD-R or CD-RW media to DVD+R,

■ You cannot back up DVD-ROM, DVD Video, DVD-R, DVD-R (Dual

■ TOSHIBA Disc Creator cannot record in packet format.

DVD+R, DVD+R (Double Layer), DVD+RW or DVD-RAM disc that may be caused by writing or rewriting with this product.

DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW or DVD-RAM media that may be caused by writing or rewriting with this product, or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents.

software.

CD Player” function to record music to DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer) or DVD+RW media.

order to copy DVD Video or DVD-ROM material that has copyright protection.

of TOSHIBA Disc Creator.

DVD-R (Dual Layer) or DVD-RW media using the “Disc Backup” function of TOSHIBA Disc Creator.

DVD+R (Double Layer) or DVD+RW media using the “Disc Backup” function of TOSHIBA Disc Creator.

Layer), DVD-RW, DVD+R, DVD+R (Double Layer) or DVD+RW to CD-R or CD-RW media using the “Disc Backup” function of TOSHIBA Disc Creator.

4-10 User’s Manual

L450/L450D

■ You might not be able to use the “Disc Backup” functi on of TOSHIBA

Disc Creator to back up a DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer) or DVD+RW disc that was made with other software on a different optical media recorder.

■ If you add data to a DVD-R, DVD-R (Dual Layer), DVD+R or DVD+R

(Double Layer) disc that you have already recorded to, you might not be able to read the added data under some circumstances. For example, it cannot be read under 16-bit operating systems, such as Windows 98SE and Windows Me, while in Windows NT4 you will need Service Pack 6 or later, and in Windows 2000, you will need Service Pack 2. In addition to this, some DVD-ROM and DVD-ROM / CD-R/RW drives cannot read this added data regardless of the operating system.

■ TOSHIBA Disc Creator does not support recording to DVD-RAM discs -

to achieve this you should use Windows Explorer or another similar utility.

■ When you back up a DVD disc, be sure that the source drive supports

recording to DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer) or DVD+RW media - if this is not th e ca se th en the source disc might not be backed up correctly.

■ When you back up a DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R,

DVD+R (Double Layer) or DVD+RW disc, be sure to use the same type of disc.

■ You cannot partially delete any data written to a CD-RW, DVD-RW or

DVD+RW disc.

Data Verification

To verify that data has been written or rewritten correctly to a data CD/DVD you should follow the steps below before you begin the write/rewrite process:

1. Select Settings for Each Mode -> Data CD/DVD in the Setting menu.

2. Display the setting dialog box by one of the following two steps:

■ Click the Recording settings button ( ) for writing on the main

toolbar in the Data CD/DVD mode.

■ Select Setting for Each Mode -> Data CD/DVD in the Setting

menu.

3. Mark the Verify written data check box.

4. Select File Open or Fu ll Compare mode.

5. Click the OK button.

How to learn more about TOSHIBA Disc Creator

Please refer to the Help files for additional TOSHIBA Disc Creator information.

■ Opening the TOSHIBA Disc Creator Manual

Start -> All Programs -> TOSHIBA -> CD&DVD Applications -> Disc Creator Help

User’s Manual 4-11

L450/L450D

TOSHIBA DVD Player

Please be aware of the following limitations when you use the TOSHIBA DVD PLAYER:

Notes on use

■ Frame dropping, audio skipping or out of sync audio and video may

■ Close all other applications when using the “TOSHIBA DVD PLAYER”.

■ Unfinalized DVDs created on home DVD recorders may not be playable

■ Use DVD-Video discs with a region code which is either “the same as

■ Do not playback DVD discs Video while watching or recording television

■ The resume function cannot be used with some discs on the “TOSHIBA

■ It is recommended the AC adaptor be connected when playing

■ Screen savers will not display while playing a movie in the “TOSHIBA

■ Do not configure the Display automatic power off function to run while

■ Do not switch to Hibernation or Sleep Mode when running the

■ Do not lock the computer using the Windows logo () + L keys or

occur during playback of some DVD Video titles.

Do not open any other applications or carry out any other operations during DVD Video playback. Playback may stop or not function properly in some situations.

on the computer.

the factory default setting” or “ALL”.

programs using other applications. Doing so may cause DVD Video playback or television program recording errors. In addition, if prescheduled recording starts during DVD Video playback it may cause DVD Video playback or television program recording errors. Please view DVD Video during times when there is no recording prescheduled.

DVD PLAYER”.

DVDVideo. Power saving features may interfere with smooth playback. When playing DVD-Video using battery power, set the Power Options to “High performance”.

DVD PLAYER”. The computer will also not go into Sleep Mode, Hibernation Mode or shutdown while using “TOSHIBA DVD PLAYER”.

the “TOSHIBA DVD PLAYER” is running.

“TOSHIBA DVD PLAYER”.

the Fn + F1 keys when running the “TOSHIBA DVD PLAYER”.

4-12 User’s Manual

L450/L450D

Display Devices & Audio

1. “TOSHIBA DVD PLAYER” will only run when “Colors” is set to “Highest

(32 bit)”. The “Colors” setting can be adjusted on the “Monitor” tab in display device property. To open it, click Start -> Control Panel ->

Appearance and Personalization -> Display -> Change display settings -> Advanced settings.

2. If the DVD Video image is not displayed on an external display or

television, stop the “TOSHIBA DVD PLAYER”, and change the screen resolution in Control Panel -> Appearance and Personalization -> Display -> Change display settings -> Advanced settings. However, video cannot be output to some external displays and televisions due to output or playback conditions.

3. When viewing DVD-Video on an external display or TV, change the

display device before playing. DVD-Video cannot be displayed simultaneously (in clone mode) on both the computer’s display panel and an external display.

4. Do not change the screen resolution while running the “TOSHIBA DVD

PLAYER”.

TOSHIBA DVD PLAY ER

1. “TOSHIBA DVD PLAYER” software is supported for playback of

DVD-Video and DVD-VR.

2. The “TOSHIBA DVD PLAYER” does not have a parental control

function.

3. In order to protect copyrights, the Windows Print Screen function is

disabled when “TOSHIBA DVD PLAYER” is running.

4. (Print Screen functions are disabled even when running other

applications besides “TOSHIBA DVD PLAYER” and when “TOSHIBA DVD PLAYER” is minimized.) Please close the “TOS HIBA DVD PLAYER” to use the Print Screen function.

5. Carry out the installation/uninstallation of the “TOSHIBA DVD PLAYER”

under a user account with administrator rights.

6. Do not change Windows Users while “TOSHIBA DVD PLAYER” is

running.

7. For some DVD Video discs, using the control window to change the

audio track will also change the subtitle track.

Starting TOSHIBA DVD PLAYER

Use the following procedure to start “TOSHIBA DVD PLAYER”.

1. Insert an DVD-Video in the DVD Super Multi drive while Windows

running. When an DVD-Video disc is set in the DVD drive, the following application selection screen may appear. If this occurs, select Play DVD movie, then click OK to launch the TOSHIBA DVD PLAYER.

2. Touch the CD/DVD panel on the Front operation pane l. Or select Start ->

All Programs -> TOSHIBA DVD PLAYER to start “TOSHIBA DVD PLA Y ER ”.

User’s Manual 4-13

7 is

L450/L450D

Operating TOSHIBA DVD PLAYER

Notes on Using “TOSHIBA DVD PLAYER”.

1. Screen display and available features may vary amongst DVD-Videos

2. Only operation buttons (including remote controller and Front operation

3. If the menu is opened in the Display Area using the Control window’s

Open TOSHIBA DVD PLAYER HELP

TOSHIBA DVD PLAYER features and instructions are also explained in detail in “TOSHIBA DVD PLAYER Help”. Use the following procedure to open “TOSHIBA DVD PLAYER Help”.

Media care

This section provides tips on protecting data stored on your CD’s, DVD’s and floppy diskettes. Handle your media with care. Following the simple precautions listed below will increase the lifetime of your media and protect the data stored on it.

and scenes.

panels) which correspond to currently available and active features will be useable during DVD playback.

Top Menu or Menu buttons, touch pad and mouse menu operations may not be able to be used.

■ Click the “Help” button ( ) in the Display Area.

CD/DVDs

1. Store your CDs and DVDs in the containers they originally came in to protect them and keep them clean.

2. Do not bend the CDs or DVDs.

3. Do not write on, apply a sticker to, or otherwise mar the surface of the CD or DVD that contains the data.

4. Hold the CD or DVD by it s outside edge or the edge on the center hole any fingerprints on the surface of the disc can prevent the drive from properly reading data.

5. Do not expose the CD or DVD to direct sunlight, extreme heat or cold.

6. Do not place heavy objects on your CDs or DVDs.

7. If your CDs or DVDs become dusty or dirty, wipe them with a clean dry cloth from the center hole outwards - do not wipe in a circular direction. If necessary, you can use a cloth that has been lightly dampened in water or a neutral cleaner but you must not use benzine, thinner or any similar cleaning solution.

4-14 User’s Manual

Floppy diskettes

The USB floppy diskette drive is available only as an option.

1. Store your floppy diskettes in the container they came in to protect them

and keep them clean. If a floppy diskette becomes dirty, clean it with a soft, lightly dampened cloth - do not use cleaning fluid.

2. Never open the shutter or touch the magnetic surface of your floppy

diskette - doing this could permanently damage it and lose data.

3. Always handle floppy diskettes with care to prevent the loss of stored

data.

4. Always apply the floppy diskette label in the correct location and never

apply a new label on top of an existing one - in this instance the label could come loose and damage the floppy diskette drive.

5. Never use a pencil for writing on a floppy diskette label as the dust from

the pencil lead could cause a system malfunction if it found its way onto the computer’s components. In this instance, always use a felt-tipped pen and write the label first before applying it to the floppy diskette.

6. Never put a floppy diskette in a location where water or other liquid may

make contact with it, or where it is excessively damp - either of these conditions could cause data loss.

7. Never use a wet or damp floppy diskette - this could damage the floppy

diskette drive or other devices within the computer.

8. Data may be lost if the floppy diskette is twisted, bent, or exposed to

direct sunlight, extreme heat or cold.

9. Do not place heavy objects on your floppy diskettes.

10.Do not eat, smoke, or use items such as erasers near your floppy

diskettes as foreign particles inside the jacket of the floppy diskette can damage the magnetic surface.

11. Magnetic energy can destroy the data on your floppy diskettes. In view

of this you should keep your floppy diskettes away from speakers, radios, televisions and other sources of magnetic fields.

L450/L450D

User’s Manual 4-15

L450/L450D

Sound system

This section describes some of the audio control functions.

Adjusting System Volume

You can control the overall level of sound using Windows Volume Mixer . To launch Volume Mixer, follow the steps below.

1. Locate the Speaker icon on the task tray.

2. Right-click the Speaker icon on the task tray.

3. Select Open Volume Mixer from the menu.

Click the Device button to display available playback devices. Select Speakers to use the internal speakers for listening. Adjust speaker volume by moving the slider up or down to raise or lower the volume. Click the

Mute button to mute the sound. Y ou may see another control under Applications in Volume Mixer. It is the

control for an application which is currently running. The Windows Sounds is always displayed since it controls the system sounds’ volume.

Changing System Sounds

System sounds are assigned to inform you when certain events happen. This section explains how select an existing scheme or save one you have modified.

To launch the configuration dialog win dow for system sounds, follow the steps below.

1. Right-click the Speaker icon on the task tray.

2. Select Sounds from the menu.

Realtek HD Audio Manager

You can confirm and change the audio configuration using the Realtek Audio Manager. To launch the Realtek Audio Manager, click Start -> Control Panel -> Hardware and Sound -> Realtek HD Audio Manager.

When you first launch the Realtek Audio Manager, you will see following device tabs. Speakers is the default output device. Microphone is the default input device. To change the default device, click the Set Default Device button under the chosen device tab.

■ Speakers is the default output device. Select it when using the internal

speakers or headphones.

■ HDMI Output should be selected when connecting the HDMI cable to

the HDMI jack for playing digital sound on digital audio equipment.

■ Microphone is the default input device. It should be selected when

using the computer’s internal microphone or an external microphone connected to the Microphone jack to record sound.

4-16 User’s Manual

L450/L450D

If an external microphone or audio cable is connected to the Microphone jack, the Realtek HD Audio Manager Connector Settings dialog will be displayed allowing selection of either “Line In” or “Mic In” input.

Information

Click the information button to view hardware information, software information, and language setting.

Speaker Configuration

Click the playback button to confirm the internal speakers or the headphone sound is coming from the right direction.

Sound Effects

This section explains how to select various sound effects.

■ Environment - simulates reverberations of sound for familiar

environments around us. You can select an existing preset in the menu.

■ Equalizer - raises or lowers a frequency of sound to simulate a popular

genre of music. You can select an existing preset in the menu.

■ Karaoke - cancels the specific frequency of sound and results in the

Vocal Cancellation. Clicking the Karaoke icon, lowers the vocal sound within music. Using the arrow buttons will adjust the musical key of the sound.

Microphone Effects

Microphone Effects are only found within Microphone window.

■ Noise Suppression reduces background noise and fan noise.

■ Acoustic Echo Cancellation reduces feedback and feedback echo.

Default Format

You can change the sample rate and bit depth of sound.

User’s Manual 4-17

L450/L450D

Using the web camera

Some models are equipped with a Web Camera. Web Camera is a device that allows you to record video or take

photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger. Toshiba Web Camera Application will help you to add various video effects to your video or photograph.

The Web camera enables the transmission of video and use of video chat via the internet using specialized applications.

The effective pixel count for this web camera is 0.3 million and 1.0 million (0.3M maximum photograph size: 640X480 pixels; 1M maximum photograph size: 1280X800 pixels).

1. Microphone

2. Web Camera

3. Web Camera LED

Figure 4-7 Web Camera

■ Please unstick the protective plastic-film before using the Web

Camera.

■ Do not point the web camera directly at the sun.

■ Do not touch or press strongly on the web camera lens. Doing so may

reduce image quality. Use an eyeglass cleaner (cleaner cloth) or other soft cloth to clean the lens if it becomes dirty.

■ Setting the image “SIZE” to more than “800x600” will cause a larger

amount of data to be written to the hard disk drive and may interfere with smooth recording.

4-18 User’s Manual

Using TOSHIBA Web Camera Application

TOSHIBA Web Camera Application is pre-configured to start when you turn on Windows 7; if you need to restart it go to Start -> All Programs -> TOSHIBA -> Utilities -> Web Camera Application.

1. Capture Still Images

2. Open/Close Preview Area

3. Delete Recorded File

4. Video Recording

5. Camera Resolution

6. Capture Settings

L450/L450D

Figure 4-8 Using the Software

Capture Still Image Click to capture a still image, and see a preview

of the captured image in preview area.

Open/Close Preview Area

Click to open Preview Area. One more to close Preview Area.

Delete Recorded File Choose a thumbnail of recorded file and click this

button to delete this file from hard disk.

Video Recording Click to start recording. One more to stop

recording and see preview of the video in preview area.

Camera Resolution Choose resolution for Preview, Capture and

Record.

Capture Settings Open Capture Settings dialog box.

Chooses from the Basic tab to select photo and video saving location, select Capture Format and Video Quality.

User’s Manual 4-19

L450/L450D

Using TOSHIBA Face Recognition

This feature uses a face verification library to verify the face data of users when they log in Windows. The user can thus avoid having to enter a password or the like, which makes the login process easier.

■ TOSHIBA Face Recognition does not guarantee the correct

identification of a user. Changes to the likeness of a registrant, such as hairstyle changes, wearing a cap, or wearing glasses may affect the recognition rates when such changes occur after the registrant had registered.

■ TOSHIBA Face Recognition may incorrectly recognize faces that are

similar to a registrant.

■ For high security purposes, TOSHIBA Face Recognition is not a

suitable substitute for Windows passwords. When security is a high priority, use your established Windows passwords to log in.

■ Bright background light and/or shadows may prevent a registrant from

being recognized correctly. In that case, log in using your Windows password. If recognition of a registrant fails repeatedly, refer to your computer documentation to learn ways to improve recognition performance.

■ TOSHIBA Face Recognition records face data in a log when face

recognition fails. When transferring ownership or disposing of your computer, please uninstall the application or delete all the logs created by the application. For details on how to do this, see help file.

Disclaimer

Toshiba does not guarantee that the face recognition utility technology will be completely secure or error-free. Toshiba does not guarantee that the face recognition utility will accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of the face recognition software or utility.

TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS, PROFITS, PROGRAMS DA TA, NETWORK SYSTEMS OR REMOVABLE STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY THEREOF.

4-20 User’s Manual

How to register the Face Recognition Data

Take a picture for facial verification purposes, and register the data needed when you log in. To regi ster the data needed when you log in, follow the steps as described below:

1. To launch this utility, cli ck Start -> All Programs -> TOSHIBA ->

Utilities -> Face Recognition.

■ The Registration screen is displayed for a logged-in user whose face

has not been registered.

■ The Management screen is displayed for a logged-in user whose face

has already been registered.

2. Click the Register face button in the Management screen.

The Registration screen is displayed.

■ If you wish to practice, click on the Next button in the Registration

screen.

■ If you do not wish to practice, click on the Skip button in the

Registration screen.

3. Click the Next button to start the guide.

4. First, take a picture while moving your neck slightly to the left and right.

5. Now take a picture while moving your neck down and up. Or click the Back button to practice the guide once more.

6. Click the Next button to start image-capturing process. Adjust the position of your face so that it fits within the face-shaped

frame.

7. Once your face has been positioned properly, the recording will commence.

Start moving your neck very slightly to the left and right, and then move your neck down and up.

8. Registration will end after you have repeatedly moved your neck left, right, down and up.

When the register succeeds, below message will be displayed on the screen: “Registration successful. Now we’ll do the verification test. Click the Next button.”

Click the Next button to perform the verification test.

9. Perform the verification test. Face the screen as you do when you register.

L450/L450D

■ If verification fails, click the Back button and re-register. Please refer to

step 8 from step 6.

10.If verification is successful, click the Next button and register an account.

1 1.Register the account. Fill in the account registration fields. Fill in the all

fields.

User’s Manual 4-21

L450/L450D

12.The Management screen is displayed. The registered account name will be displayed. Clicking on it will cause

the captured image of your face to be displayed on the left.

How to Delete the Face Recognition Data

Delete image data, account information, and personal record data created during registration. To delete the Face Recognition Data, follow the steps as described below:

1. To launch this utility, click Start -> All Programs -> TOSHIBA -> Utilities -> Face Recognition.

The Management screen is displayed.

2. Select a user which is deleted in the Management screen.

3. Click the Delete button. “You are about to delete the user data. Would you like to continue?” will be displayed on the screen.

■ If you do not want the data to be deleted, click the No button and

you will then be returned to the Management screen.

■ Clicking on the Yes button will remove the selected user from the

Management screen.

How to launch the help file

For further information on this utility, please refer to the help file.

1. To launch the help file, click Start -> All Programs -> TOSHIBA ->

Utilities -> Face Recognition Help.

Windows Logon via TOSHIBA F ace Recognition

This section explains how to login to Windows with TOSHIBA Face Recognition. Two authentication modes are provided.

■ 1:N Mode Login screen: If the face authentication tile is selected by

default, you can log in without using the keyboard or mouse.

■ 1:1 Mode Login screen: This mode is essentially the same as 1:N

Mode, but the Select Account screen will appear before the Display Captured Image screen, and you will need to select the user account to be authenticated in order to start the authentication process.

1:N Mode Login Screen

1. Turn on the computer.

2. The Select Tiles screen will be displayed.

3. Select Start face recognition ( ).

4. “Please face the camera” will be displayed.

5. Verification will be performed. If the authentication is successful, the image data taken in step 4 will be faded in and placed over one another.

■ If an error occurs during authentication, you will be returned to the

Select Tiles screen.

4-22 User’s Manual

6. Windows Welcome screen will be displayed, and will be logged in

automatically to Windows.

1:1 Mode Login screen

1. Turn on the computer.

2. The Select Tiles screen will be displayed.

3. Select Start face recognition ( ).

4. The Select Account screen will be displayed.

5. Select the account, and click the Arrow button.

6. “Please face the camera” will be displayed.

7. Verification will be performed. If the authentication is successful, the

image data taken in step 6 will be faded in and placed over one another.

■ If an error occurs during authentication, you will be returned to the

Select Tiles screen.

8. Windows Welcome screen will be displayed, and will be logged in

automatically to Windows.

■ If authentication was successful, but an authentication error

subsequently occurred during the login to Windows, you will be asked to provide your account information .

Wireless LAN

L450/L450D

The Wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE802.11 Wireless LAN standard.

■ Frequency Channel Selection of 5GHz for IEEE 802.11a or n draft 2.0

■ Frequency Channel Selection of 2.4GHz for 802.11b/g or n draft 2.0

■ Roaming over multiple channels

■ Card power management

■ Wired Equivalent Privacy (WEP) data encryption based on an 128-bit

encryption algorithm

■ Wi-Fi Protected Access™ (WPA™) support

■ Advanced Encryption Standard (AES) data encryption

The transmission speed over the wireless LAN, and the distance over which the wireless LAN can reach, may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, client design and software/hardware configurations. The transmission rate described is the theoretical maximum speed as specified under the appropriate standard - the actual transmission speed will be lower than the theoretical maximum speed.

User’s Manual 4-23

L450/L450D

Setting

1. Click Start -> Control Panel -> Network and Internet -> Network and Sharing Center -> Connect to a network.

2. Choose a wireless network from the available connection window and click Connect.

3. Follow the wizard. You will need the name of the wireless network together with security settings. Consult the documentation accompanied with your router or ask your wireless network administrator for the settings.

Security

■ TOSHIBA strongly recommend that you enable encryption functionality,

otherwise your computer will be open to illegal access by an outsider using a wireless connection. If this occurs, the outsider may illegally access your system, eavesdrop, or cause the loss or destruction of stored data.

■ TOSHIBA is not liable for the loss of data due to eavesdropping or

illegal access through the wireless LAN and the damage thereof.

Wireless communication indicator

The wireless communication indicator shows the status of the computer’s wireless communication functions.

Indicator status Indication

Indicator off No wireless functionality is available. Indicator glows Wireless LAN is turned on by an application.

If you used the T askbar to disable the wireless LAN, restart the computer or perform the following procedure to re-enable it: Start -> Control Panel ->

System and Security -> System -> Device Manager -> Network adapters and right click the wireless device then choose enable.

4-24 User’s Manual

LAN

LAN cable types

L450/L450D

The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-TX). This section describes how to connect/disconnect to a LAN.

Do not install or remove a memory module while Wake-up on LAN is enabled.

■ The Wake-up on LAN function consumes power even when the system

is off. Leave the AC adaptor connected while using this feature.

■ The Link speed (10/100 megabits per second) changes automatically

depending on the network conditions (connected device, cable or noise, and so on).

The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures.

If you are using Fast Ethernet LAN (100 megabits per second, 100BASE-TX), be sure to connect with a CAT5 cable or higher. You cannot use a CAT3 cable.

If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you can connect with a CAT3 or higher cable.

Connecting the LAN cable

To connect the LAN cable, follow th e steps as detailed below:

■ Connect the AC adaptor before connecting the LAN cable. The AC

adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up.

■ Do not connect any other cable to the LAN jack except the LAN cable.

Otherwise, malfunctions or damage may occur.

■ Do not connect any power supplying device to the LAN cable that is

connected to the LAN jack. Otherwise, malfunctions or damage may occur.

1. Turn off the power to the computer and to all external devices

connected to the computer.

2. Plug one end of the cable into the LAN jack. Press gently until you hear

the latch click into place.

User’s Manual 4-25

L450/L450D

3. Plug the other end of the cable into a LAN hub connector or router. Check with your LAN administrator and hardware or software vendor before using or configuring a network connection.

When the computer is exchanging data with the LAN, the LAN Active indicator glows yellow. When the computer is connected to a LAN hub but is not exchanging data, the Link indicator glows.

Disconnecting the LAN cable

To disconnect the LAN cable, follow the steps as detailed below:

Figure 4-9 Connecting the LAN cable

Make sure the LAN Active indicator (amber LED) is out before you disconnect the computer from the LAN.

1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector.

2. Disconnect the cable from the LAN hub or router in the same manner. Check with your LAN administrator and hardware or software vendor before disconnecting from the hub.

Cleaning the computer

To help ensure long, trouble-free operation, keep the computer free of dust and dirt, and use care with all liquids around it.

■ Be careful not to spill liquids into the computer . If th e computer do es get

wet, turn the power off immediately and let the computer d ry completely in these circumstance you should get the computer inspected by an authorized service provider in order to assess the scope of any damage.

■ Clean the plastics of the computer using a slightly water dampened

cloth.

■ You can clean the disp lay screen by spraying a small amount of glass

cleaner onto a soft, clean cloth and then wiping the screen gently with the cloth.

4-26 User’s Manual

Using the cleaning cloth

Some models include 1 cleaning cloth. The cleaning cloth can be used to wipe away dust and fingerprints from the

keyboard and palm rest area of your computer.

■ When wiping the keyboard, palm rest and display panel, do so gently

without using excessive pressure.

■ Do not use the cleaning cloth when it is dirty or wet.

■ Do not use the cleaning cloth soaked with water, detergents or volatile

organic solvents.

It is recommended that you wash the cloth if it gets soiled using a gentle, mild detergent and rinse it well. Allow it to air dry completely before using it again on your computer.

Never spray cleaner directly onto the computer or let liquid run into any part of it. Never use harsh or caustic chemical products to clean the computer.

■ Use the cleaning cloth to wipe away dust, fingerprints and similar from

the keyboard, palm rest and other parts. For precautions on use refer to the Using the cleaning cloth section in Chapter 4, Operating Basics.

Moving the computer

L450/L450D

While the computer is designed for rugged durability you should exercise a few simple precautions when moving it in order to help ensure trouble-free operation.

■ Make sure all disk/disc activity has ended before moving the computer -

check that the HDD and other indicators on the front of the computer are off.

■ If a CD or DVD is in the drive, remove it and make sure that the disc tray

is securely closed.

■ Turn off (shut down) the computer.

■ Disconnect the AC adaptor and all peripherals before moving the

computer.

■ Close the display panel.

■ Do not pick up the computer by its display panel.

■ Before carrying your computer, shut it down, disconnect the AC adaptor

and allow it to cool down - a failure to follow this instruction may result in minor heat injury.

■ Be careful not to subject the computer to impact or shock - a failure to

follow this instruction could result in damage to the computer, computer failure or loss of data.

■ Never transport your computer with any cards installed - this may cause

damage to either the computer and/or the card resulting in product failure.

User’s Manual 4-27

L450/L450D

■ Always use a suitable carry case when transporting the computer.

■ When carrying your computer, be sure to hold it securely so that it does

not fall or hit anything.

■ Do not carry your computer by holding any of its protruding elements.

Heat dispersal

T o protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. You can select whether to control the CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. These functions are controlled within the Power Options.

When the CPU temperature falls to a normal range, the fan is turned off and the CPU operation returns to standard speed.

If the CPU temperature reaches an unacceptably high level with either setting, the system automatically shuts down to prevent damage. Data in memory will be lost.

4-28 User’s Manual

The Keyboard

The computer’s keyboard layouts are compatible with a 104/105-key enhanced keyboard - by pressing some keys in combination, all of the 104/105-key enhanced keyboard functions can be performed on the computer.

The number of keys available on your keyboard will depend on which country/region your computer is configured for, with keyboards being available for numerous languages.

In use there are six different types of keys, specifically typewriter keys, function keys, soft keys, Hot keys, Windows special keys and the keypad overlay.

Typewriter keys

L450/L450D

Chapter 5

The typewriter keys produce the upper-case and lower-case letters, numbers, punctuation marks, and special symbols that appear on the screen. However, there are some differences between using a typewriter and using a computer keyboard:

■ Letters and numbers produced in computer text vary in width. Spaces,

which are created by a “space character” may also vary depending on line justification and other factors.

■ The lowercase l (el) and the number 1 (one), together with the

uppercase O (oh) and the 0 (zero), are not interchangeable on computers as they are on a typewriter.

■ The CAPS LOCK function key locks only the alphabetic characters into

upper-case while the Shift Lock function on a typewriter places all keys in the shifted position.

■ The SHIFT keys, the Tab key, and the BACK SPACE key perform the

same function as their typewriter counterparts but also have special computer functions.

Never remove the key caps on your keyboard. Doing so could cause damage to the parts under the key caps.

User’s Manual 5-1

L450/L450D

Function keys: F1 … F12

The function keys (not to be confused with the special FN key) are the twelve keys at the top of your keyboard - these keys function differently from other keys.

F1 through F12 are called function keys because they execute programmed functions when pressed and, when used in combination with the FN key, those keys marked with icons also execute specific functions on the computer. Please refer to the section, Soft keys: FN key

combinations, in this chapter for further information, taking care to note that

the function executed by individual keys will depend on the software you are using.

Soft keys: FN key combinations

The FN (function) key is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.

Please note that some software may disable or interfere with soft-key operations, and that the soft-key settings are not restored when the computer returns from Sleep Mode.

Emulating keys on an enhanced keyboard

Figure 5-1 A 104-key enhanced keyboard layout

This computer’s keyboard is designed to provide all the features of the 104-key enhanced keyboard.

Since the keyboard is smaller and has fewer keys, some of the enhanced keyboard functions must be simulated using two keys instead of one on the larger keyboard.

The FN key can be combined with the following keys to simulate functions similar to those of keys on the 104/105 key enhanced keyboard which are not on this computer’s keyboard.

5-2 User’s Manual

Hot keys

L450/L450D

Press FN + F10 or FN + F11 to access the computer’s integrated keypad. When activated, the keys with grey markings on their bottom edge become either numeric keypad keys (FN + F11) or cursor control keys (FN + F10). Please refer to the Keypad overlay section in this chapter for more information on how to operate these keys, taking care to note that the power on default for both settings is off.

Press FN + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.

Press FN + ENTER to simulate ENTER on the enhanced keyboard’s numeric keypad.

Hot keys (pressing FN + a function or ESC key) let you enable or disable certain features of the computer.

Mute: Pressing FN + ESC turns the volume on and off.

Lock: Pressing FN + F1 enters “Lock computer mode”. To restore your

desktop, you need to log on again.

Power Plan: Pressing FN + F2 changes the power settings.

User’s Manual 5-3

L450/L450D

Sleep: Pressing FN + F3 switches the system to Sleep Mode.

Hibernate: Pressing FN + F4 switches the system to Hibernation Mode.

Output: Pressing FN + F5 changes the active display device.

Brightness (Down): Pressing FN + F6 decreases the computer’s display

panel brightness in individual steps.

Brightness (Up): Pressing FN + F7 increases the computer’s display panel brightness in individual steps.

Wireless: Pressing FN + F8 switches the active wireless device.

If no wireless communication device is installed, no dialog box will appear.

Touch Pad: Pressing FN + F9 enables or disables the Touch Pad function.

5-4 User’s Manual

Zoom: Pressing FN + Space changes the display resolution.

TOSHIBA Zooming Utility (reduce): Pressing FN + 1 reduces the icon

size on the desktop or the font sizes within one of the supported application windows.

TOSHIBA Zooming Utility (enlarge): Pressing FN + 2 enlarges the icon size on the desktop or the font sizes within one of the supported application windows.

FN Sticky key

You can use the TOSHIBA Accessibility Utility to make the FN key sticky, that is, you can press it once, release it, and then press an “F Number” key. To start the TOSHIBA Accessibility utility, click Start -> All Programs

-> TOSHIBA -> Utilities -> Accessibility.

L450/L450D

Windows special keys

The keyboard provides two keys that have special functions in Windows: Windows Start Button activates the Start menu and the other, the application key, has the same function as the secondary mouse button.

This key activates the Windows Start menu.

This key has the same function as the secondary (right) mouse button.

User’s Manual 5-5

L450/L450D

Keypad overlay

Your computer’s keyboard does not have a separate numeric keypad but includes a numeric keypad overlay which functions like one - this is located in the center of the keyboard with the relevant keys having grey letters at their front edge. The overlay provides the same functions as the numeric keypad on a standard 104/105-key enhanced keyboard.

Turning on the overlays

The numeric keypad overlay can be used for numeric data input or cursor and page control.

Arrow mode

To turn on Arrow Mode, press FN + F10 - the Arrow mode indicator lights and you are able to access cursor and page control functions by using the keys. You are able to press FN + F10 again to turn off this overlay function.

Numeric mode

To turn on Numeric Mode, press FN + F11 - the Numeric Mode indicator lights and you are able to access numeric characters by using the keys. You are able to press FN + F11 again to turn off this overlay function.

Figure 5-2 The numeric keypad overlay

5-6 User’s Manual

Temporarily using normal keyboard (overlay on)

While using the overlay, you can temporarily access the normal keyboard functions without having to turn the overlay off:

1. Hold FN and press any other key - this key will operate as if the overlay

were off.

2. Type upper-case characters by holding FN + SHIFT and pressing a

character key.

3. Release FN to continue using the selected overlay function.

Temporarily using overlay (overlay off)

While using the normal keyboard function, you can temporarily use the keypad overlay without having to turn it on:

1. Press and hold down FN.

2. Check the keyboard indicators as pressing the FN key will turn on the

most recently used overlay function - if the Numeric Mode indicator lights you can use the overlay for numeric entry, while if the Arrow Mode indicator lights, you can use the overlay for cursor and page control function.

3. Release FN to return to normal keyboard operation.

Temporarily changing modes

If the computer is in Numeric Mode, you can switch temporarily to Arrow Mode by pressing a SHIFT key, while if it is in Arrow Mode, you can switch

temporarily to Numeric Mode by also pressing a SHIFT key.

L450/L450D

Generating ASCII characters

Not all ASCII characters can be generated using normal keyboard operation, but you are able to generate these characters using their specific ASCII codes.

With the overlay on:

1. Hold down ALT.

2. Using the overlay keys, type the ASCII code of the character you

require.

3. Release ALT - the ASCII character will appear on the display screen. With the overlay off:

1. Hold down ALT + FN.

2. Using the overlay keys, type the ASCII code of the character you

require.

3. Release ALT + FN - the ASCII character will appear on the display

screen.

User’s Manual 5-7

L450/L450D

5-8 User’s Manual

Chapter 6

Power and Power-up Modes

The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power-up modes.

Power conditio n s

The computer’s operating capability and battery charge status are affected by different power conditions, including whether an AC adaptor is connected, whether a battery pack is installed and what the charge level is for that battery.

Table 6-1 Power conditions

L450/L450D

Power on

AC adaptor connected

User’s Manual 6-1

Battery fully charged

Battery partially charged or no charge

No battery installed

• Operates

• LED: Battery green DC IN green

• Operates

• Quick Charge

• LED: Battery amber DC IN green

• Operates

• No charge

• LED: Battery off

DC IN green

Power off (no operation)

• LED: Battery green DC IN green

• Quick charge

• LED: Battery amber DC IN green

• No charge

• LED: Battery off DC IN green

L450/L450D

AC adaptor not connected

Battery charge is above low battery trigger point

Battery charge is below low battery trigger point

Battery charge is exhausted

No battery installed • Cannot operate

Power indicators

As shown in the below table, the Battery, DC IN and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status.

Table 6-1 Power conditions continued

Power on Power off

(no operation)

• Operates

• LED: Battery off DC IN off

• Operates

• LED: Battery flashes Amber DC IN off

Computer goes into Sleep Mode and shuts down

• LED: Battery off

DC IN off

Battery indicator

Check the Battery indicator to determine the status of the battery pack the following indicator conditions should be noted:

Flashing amber

Amber

Green

No light

If the battery pack becomes too hot while it is being charged, the charge will stop and the Battery indicator will go out. When the battery pack’s temperature falls to a normal range, charging will resume - this process will occur regardless of whether the computer’s power is on or off.

6-2 User’s Manual

The battery charge is low, the AC adaptor must be connected in order to recharge the battery.

Indicates the AC adaptor is connected and the battery is charging.

Indicates the AC adaptor is connected and the battery is fully charged.

Under any other conditions, the indicator does not light.

Toshiba L450D, L450 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Table of Contents

Preface

General Precautions

Equipment checklist

Features

Special features

TOSHIBA Value Added Package

Utilities and Applications

Options

Front with the display closed

Left side

Right side

Back side

Underside

Front with the display open

System indicators

Optical disc drive

AC adaptor

Connecting the AC adaptor

Opening the display

Turning on the power

Starting up for the first time

Turning off the power

Restarting the computer

System Recovery Options

Using the Touch Pad

Using the optical disk drive

Writing CD/DVD on DVD Super Multi drive

Media care

Sound system

Using the web camera

Using TOSHIBA Web Camera Application

Using TOSHIBA Face Recognition

Wireless LAN

Cleaning the computer

Moving the computer

Heat dispersal

Typewriter keys

Function keys: F1 … F12

Soft keys: FN key combinations

Hot keys

Windows special keys

Keypad overlay

Generating ASCII characters

Power conditio n s

Power indicators