Toshiba IK-DF03A User Manual

INSTRUCTION MANUAL

DOME CAMERA

IK-DF03A

Please read this manual thoroughly before use, and keep it handy for future reference.

Record in space provided below the Model
# and the Serial # as found on the label on
the bottom of this unit.
Model # IK-DF03A Serial #
Retain this information for future reference.

TABLE OF CONTENTS

IMPORTANT SAFEGUARDS

····································································1

COMPONENTS1. ······························································································ 4
PART NAMES AND FUNCTIONS2. ·································································· 5
CONNECTIONS3. ····························································································· 5
INSTALLATION4. ······························································································· 6
BACKLIGHT COMPENSATION5. ······································································7
NOTES ON USE AND INSTALLATION6. ·························································· 8
IN CASE OF PROBLEMS7. ·············································································· 9
SPECIFICATIONS8. ·························································································· 9
EXTERIOR VIEW9. ························································································· 10

For information on our latest products and peripheral devices, refer to the following
Web page.



http://www.toshibasecurity.com

The above URL is subject to change without prior notice. If the URL changes, refer
to the Toshiba website
(http://www.toshiba.com.)

- 1 -

IMPORTANT SAFEGUARDS

Read Instructions1.

Read all the safety and operating instructions before
operating the product

Retain Instructions2.

Retain the safety instructions and instruction manual for
future reference.

Warnings3.

Comply with all warnings on the product and in the
instruction manual.

Follow Instructions4.

Follow all operating and use instructions.

Cleaning5.

Disconnect this video product from the power supply before
cleaning.

Attachments6.

Do not use attachments not recommended by the video
product manufacturer as they may cause hazards.

Water and Moisture7.

Do not use this video product near water. Some examples
are: near a bath tub, wash bowl, kitchen sink, or laundry tub,
in a wet basement, or near a swimming pool.

Accessories8.

Do not place this video product on an unstable car t, stand,
tripod, bracket or table. The video product may fall, causing
serious injury to a person, or serious damage to the product.
Use only with stand, tripod, bracket, or table recommended
by the manufacturer, or sold with the video product. Any
mounting of the product should follow the manufacturer’s
instructions, and should use a mounting accessor y
recommended by the manufacturer.

Ventilation9.

This video product should never be placed near or over a
radiator or heat register. If this product is placed in a built
in installation verify that there is proper ventilation so that
the camera temperature operates within the recommended
temperature range.

Power Sources10.

This video product should be operated only from the type of
power source indicated on the information label. If you are
not sure of the type of power supply at your location, consult
your product dealer.

Power-Cord Protection11.

Power cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against
them. Pay particular attention to cords at plugs, screws and
the point where they exit the product.

Installation12.

Install this video product on a secure part of the ceiling or
wall. If installed on an unsecured location the camera
could fall causing injury and damage.

Lightning13.

For additional protection on this video product during a
lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and
disconnect the power supply and cable system. This will
prevent damage to the video product due to lightning and
power-line surges. If lightning occurs, do not touch the unit
or any connected cables in order to avoid electric shock.

Overloading14.

Do not overload the power supply or extension cords as this
can result in a risk of fire or electric shock.

Object and Liquid Entry15.

Never push objects of any kind into this video product
through openings as they may touch dangerous electrical
points or short-out parts that could result in a fire or electrical
shock. Never spill liquid of any kind on the video product.

Servicing16.

Do not attempt to service this video product yourself as
opening or removing covers may expose you to dangerous
electrical or other hazards. Refer all servicing to qualified
service personnel.

Damage Requiring service17.

Disconnect this video product from the power supply and
refer servicing to qualified service personnel under the
following conditions.

a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the

video product.
c. If the video product has been exposed to rain or water.
d. If the video product does not operate normally by following

the operating instructions in the instruction manual. Adjust

only those controls that are covered by the instruction

manual as an improper adjustment of other controls may

result in damage and will often require extensive work by

a qualified technician to restore the video product to its

normal operation.
e. If the video product has been dropped or the cover has

been damaged.
f. When the video product exhibits a distinct change in

performance which indicates a need for service.

Replacement Parts18.

When replacing parts be sure the service technician uses
parts specified by the manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock
or other hazards.

Safety Check19.

Upon completion of any service or repairs to this video
product, ask the ser vice technician to perform safety checks
to determine that the video product is in proper operating
condition.

- 2 -

CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightening flash with arrowhead
symbol, within an equilateral
triangle, is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product's enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.

The exclamation point within
an equilateral triangle is
intended to alert the user to the
presence of important operating
and maintenance (servicing)
instructions in the literature
accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.

FIELD INSTALLATION MARKING:

WORDED: “THIS INSTALLATION
SHOULD BE MADE BY A
QUALIFIED SERVICE PERSON
AND SHOULD CONFORM TO ALL
LOCAL CODES.”

FCC (USA)-INFORMATION
NOTE : This equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.

USER-INSTALLER CAUTION : Your authority to operate this FCC verified
equipment could be voided if you make changes or modifications not expressly
approved by the party.

- 3 -

Disclaimer

We disclaim any responsibility and shall be held harmless for any damages or
losses incurred by the user in any of the following cases:

Fire, earthquake or any other act of God; acts by third parties; misuse by the 1.
user, whether intentional or accidental; use under extreme operating conditions.
Malfunction or non-function resulting in indirect, additional or consequential 2.
damages, including but not limited to loss of expected income and suspension of
business activities.
Incorrect use not in compliance with instructions in this instruction manual.3.
Malfunctions resulting from misconnection to other equipment.4.
Repairs or modifications made by the user or caused to be made by the user 5.
and carried out by an unauthorized third party.
Notwithstanding the foregoing, Toshiba’s liabilities shall not, in any 6.
circumstances, exceed the purchase price of the product.

Copyright and Right of Portrait

There may be a conflict with the Copyright Law and other laws when a customer
uses, displays, distributes, or exhibits an image picked up by the camera without
permission from the copyright holder. Please also note that transfer of an image
or file covered by copyright is restricted to use within the scope permitted by the
Copyright Law.

Protection of Personal Information

Images taken by the camera that reveal the likeness of an individual person may be
considered personal information. To disclose, exhibit or transmit those images over
the internet or otherwise, consent of the person may be required.

Usage Limitation

The product is not designed for any “critical applications.” “Critical applications”
means life support systems, exhaust or smoke extraction applications, medical
applications, commercial aviation, mass transit applications, military applications,
homeland security applications, nuclear facilities or systems or any other
applications where product failure could lead to injury to persons or loss of life or
catastrophic property damage. Accordingly, [Toshiba / TAIS] disclaims any and all
liability arising out of the use of the product in any critical applications.

- 4 -

1. COMPONENTS

(1) Camera ·········································································································1
(2) Accessories

Instruction Manual(a) ···················································································1

Power connector(b) ······················································································1
Screws (c) ···································································································· 2
Anchor(d) ·····································································································2
Alignment Sticker (Guide pattern)(e) ···························································1

- 5 -

2. PART NAMES AND FUNCTIONS

3. CONNECTIONS

Notes on connecting

Power plugs of connected equipment must be disconnected before camera •
installation.

A 75-ohm coaxial cable with connector (3C-2V or 5C-2V) is required for •
standard connection.

For details of wiring and operation of equipment to be connected, refer to •
their operation manuals.

A power supply with cable, connectors and coaxial cable are not supplied •
with the camera.

Video Wire (BNC Tap)

Connect the video cable to a monitor
or video device.
The image is outputted when
powered on.
Length: approx. 12 inches (300mm )

Pan ADJ

Turn this domed cover by hand and
adjust the angle of a video image.

Power Input Wire

Connect the power cable to
12V DC.
Length: approx. 12 inches
(300mm )

Do not touch this screw.

Tilt ADJ screw

Turn this screw with
a driver and adjust
the angle of a video
image.

- 6 -

Display Monitor

12V DC power supply.
GND

BNC Connector

Connector

①

Red

②

Black

Do not overload power supply

The recommended power supply for this camera is 5 watts minimum at 12V DC.

4. INSTALLATION

Notes:

This camera is for indoor application.•
The attached screws and anchors are used to install the camera to a solid •

surface. (e.g.concrete) If installing to loose or thin material surfaces, use
the appropriate anchors (not included) with the screws.

Install the camera firmly.•

4-1 Mounting the camera to a solid surface

(1) Attach the alignment sticker to the surface.
(2) Drill one hole for cable at the center.
(3)

Drill two pilot holes (Ø7mm×40mm(D)) through the two circles on the sticker.
(4) Hammer the supplied plastic anchors into the holes.
(5)

Align the two holes on each side of the camera base with the two plastic

anchors; insert the supplied screws with camera to corresponding holes.

This Power connector is provided as an
accessory.

Recommended power cord is a minimum wire
size of 18 AWG.

- 7 -

Alignment
Sticker

Pan angle 350˚

Tilt angle

+75

°

0

°

4-2 Adjusting the view angle

(1) The lens pan direction can be adjusted by rotating the dome cover by hand.

Note:

Do not rotate the dome over 350•



, otherwise the inner connector may break,

damaging the camera.
(2) Tilt angle of the lens can be adjusted within the limit of 0 to +75 by rotating

“Tilt ADJ screw” with a compatible screw driver.

Note:

Do not set up the lens at the limit position (+75•



) of tilt angle, otherwise the

image of upper left and upper right may drop out.

5. BACKLIGHT COMPENSATION (BLC)

The BLC function of this camera is always ON.
The exposure is automatically adjusted so that the best picture is obtained at a
monitor zone of about 75% in horizontal and about 75% in vertical direction.

- 8 -

6. NOTES ON USE AND INSTALLATION

Do not aim the camera at the sun•

Never aim the camera at the sun even with the camera power off.

Do not shoot intense light•

Intense light such as a spotlight may cause a bloom or smear. A vertical

stripe may appear on the screen. However, this is not a malfunction.

Treat the camera with care•

Do not drop the camera or subject it to intense vibration.

Never touch internal parts•

Do not touch the internal parts of the camera other than the parts specified.

Do not splash water on the camera•

Install the camera where the camera can be kept dry. If the camera gets

wet, turn off the power and contact your dealer.

Keep the camera installation away from video noise•

If cables are wired near electric lighting wires or a TV set, noise may appear

in images. In this event relocate cables or reinstall equipment.

Check the ambient temperature and humidity•

Avoid using the camera where the temperature is hotter or colder than the

specified operating range. Doing so could affect the internal parts or cause

the image quality to deteriorate. Special care is required to use the camera

at high temperature and humidity.

Should you notice any trouble•

If any trouble occurs while you are using the camera, turn off the power

and contact your dealer. If you continue to use the camera when there is

something wrong with it, the trouble may get worse and an unpredictable

problem may occur.

- 9 -

7. IN CASE OF PROBLEMS

Condition Check Points

No image • Are the camera and connected equipment turned on?

• Are wires connected correctly?

Unnatural color • Is the display monitor adjusted correctly?

• Is the lighting too dim?

Flicker noise • Under the uorescent lamp of 60 Hz,

flicker noise rarely occurs.

8. SPECIFICATIONS

1. Image System
Image Device 1/3 inch CCD image sensor
Pixel Elements 768 (H) x 492 (V)

2. Electrical
TV System NTSC 2:1 Interlace,

15.734 KHz horizontal, 59.94 Hz vertical
Horizontal Resolution 480 TV lines (typical)
S/N Ratio 48 dB
Minimum Illumination 0.5 lux (at 10 IRE,)
Gain Control Auto (AGC)
White Balance Auto
White Balance Range 2,500 K to 9,500 K
Electric Shutter

1/60 s to 1/100,000 s

Backlight Compensation

Always On

Video Output Signal VBS (1.0 Vp-p, 75 ohms unbalanced, BNC)

Synchronization System

Synchronization System

Internal

- 10 -

3. Mechanical
Weight 0.729 lbs (330 g )
Dimension 3.97(D) x 2.64(H) inches ( 100mm(D) x 67mm(H) )
Pan and Tilt angle 350° (Pan), 75° (Tilt)
Ingress Protection

Rating

IP65

4. Optical
Built-in Lens f = 3.6 mm, F 2.0
View Angle of Lens 71°(H), 53°(V)

5. Power
Input Voltage 12V DC +/-10 %
Current Consumption 0.16 A

6. Environmental
Operating Temperature

and Humidity

14°F to 122°F (-10°C to +50°C )
20 % to 90 % RH

Storage Temperature
and Humidity

-4°F to 140 °F (-20°Cto 60°C)
90 % RH

Design and specifications are subject to change without notice.

9. EXTERIOR VIEW

2.64

(67)

3.97

(100)

4.57

(116)

4.24

(107.6)

2-Ø 0.177

(4.5)

Dimensions: Inch (mm)

- 11 -

LIMITED WARRANTY

CCD SECURITY CAMERA IK-DF03A

The Imaging System Division (“ISD”) of Toshiba America Information Systems,Inc.makes the following limited warranties with regard to this
CCD Camera Model IK-DF03A (“Product”).These limited warranties extend to the Original End-User (“You [r]”).

Three (3) Year Limited Warranty of Labor and Parts ISD warrants that this Product will perform in accordance with specifications for a
period of three (3) years from the date of purchase by the Or iginal End-User. During this three (3) year period, ISD will repair or replace the
Product, if it does not perform as warranted. In order to take advantage of this Limited Warranty. You must: (a) call [phone] to receive a
RMA number:and (b) pay all transportation and insurance charges for shipment of the Product to the ASP or Toshiba Exchange Center. ISD
reserves the right to substitute factory refurbished parts in place of those in need of repair.

Instruction Manual (Owner's Manual) :You should read the Instruction Manual (Owner's Manual) thoroughly before operating this Product.
Before seeking warranty ser vice, you should check the troubleshooting guide in the Instruction Manual (Owner's Manual) and follow the
instructions to correct the problem.

How to Obtain Warranty Service Step-by-step Procedures :To obtain warranty service. You should :

1. Contact Toshiba at [phone] to first verify operation or installation assistance. (877)855-1FIX

2. If technical support determines that the unit is defective,an RMA will be issued with return instructions for repair.

3. Securely pack the Product in the original carton and external shipping pack, include a letter explaining the problem with a copy of the bill of
sale or proof of purchase.

4. Prepay all transportation and insurance costs.

Your Responsibilities: This Limited Warranty is subject to the following conditions:

1. You must provide the bill of sale or proof of purchase at the time that warranty service is required.

2. You must notify [phone] within (30) days after you discover that the product does not perform in accordance with specifications during
the Limited Warranty period.

3. You must pack the Product in its original carton using the original packing material.Then insert the original carton containing the Product
into another carton with additional packing material before shipping the Product to an ASP or Toshiba Exchange Center.

DISCLAIMERS: ALL OTHER EXPRESS OR IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. SOME STATES DO NOT ALLOW
THE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATIONS MAY NOT APPLY TO YOU.

IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE, YOUR SOLE AND EXCLUSIVE REMEDY SHALL BE
THE REPAIR OR REPLACEMENT OF THE PRODUCT. IN NO EVENT WILL ISD OR ITS PARENT COMPANY OR ANY ASP BE LIABLE
TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT. THIS LIMITATION
APPLIES TO DAMAGES OF ANY KIND, INCLUDING ANY DIRECT OR INDIRECT DAMAGES, LOST PROFITS, LOST SAVINGS OR
OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, WHETHER FOR BREACH OF CONTRACT, TORT OR
OTHERWISE, OR WHETHER ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH PRODUCT, EVEN IF TAIS, ITS PARENT
COMPANY, OR AN ASP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR SOME
PRODUCTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE
TO STATE.

THIS LIMITED WARRANTY SHALL BE VOID IF THE PRODUCT OR PARTS HAVE BEEN SUBJECTED TO MISUSE, ABUSE, ACCIDENT,
IMPROPER INSTALLATION, IMPROPER MAINTENANCE, OR USE IN VIOLATION OF ISD'S WRITTEN INSTRUCTIONS, OR WHERE THE
PRODUCT HAS BEEN ALTERED OR MODIFIED WITHOUT ISD'S PRIOR AUTHORIZATION, OR UPON THE REMOVAL OR ALTERATION
OF ISD'S FACTORY SERIAL NUMBER. LABOR SERVICE CHARGES FOR PRODUCT INSTALLATION, SET UP AND ADJUSTMENT OF
CONTROLS ARE NOT COVERED BY THIS LIMITED WARRANTY.

No person, agent, distributor,dealer,authorized ser vice provider, or company is authorized to change, modify, or extend the terms of this
Limited Warranty in any manner whatsoever. The time within which an action must be commenced to enforce any obligation of ISD arising
under this Limited Warranty or under any statute, or law of the United States or any state thereof, is herby limited to one (1) year from the date
You discovered or should have discovered the problem. This limitation does not apply to implied warranties arising under state law.
Some states do not permit limitation of the time within which You may bring an action beyond the limits provided by state law, so the above
provision may not apply to You. This Limited Warranty gives You spacific legal rights and You may also have other r ights which vary from state
to state.

TOSHIBA AMERICA INFORMATION SYSTEMS, INC.

Imaging Systems Division