Toshiba DVR20 User Manual

E9TK4BD_EN.book Page 1 Wednesday, January 6, 2010 10:05 PM

DVD / VIDEO CASSETTE RECORDER

DVR20KB

OWNER’S MANUAL

PAL

Introduction Connections Playback Editing OthersFunction SetupRecording VCR Functions

TV View Operation

Basic Setup /

DVD

VCR

For Customer Use:

Carefully read the Model No. and Serial No. located at the back of the unit and enter the information below. Retain this information for future reference. Model No. __________________________ Serial No. __________________________

E9TK4BD_EN.book Page 2 Wednesday, January 6, 2010 10:05 PM

Introduction

Precautions

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The important note is located on the rear of the cabinet.

Laser Safety

This unit employs a laser. Only qualified service personnel should remove the cover or attempt to service this unit, due to the possibility of eye injury.

CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR

CAUTION: VISIBLE AND INVISIBLE LASER RADIATION

LOCATION: INSIDE, NEAR THE DECK MECHANISM.

PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO BEAM.

Power Supply

The power supply is connected and the unit is live when the mains cable is plugged into a 220 - 240 V~, 50 Hz AC outlet. To operate the unit, press [B ON\STANDBY].

WARNING: LIVE PARTS INSIDE.

DO NOT REMOVE ANY SCREWS.

Caution

1. Do not attempt to open the cabinet. There are no parts inside you can service. Refer all servicing to qualified service personnel.

2. Slots and openings in the cabinet at the sides and underneath are provided for ventilation. To ensure reliable operation and to protect the unit from overheating, these openings must not be blocked or covered. Avoid installation in enclosed spaces such as bookcases unless suitable ventilation is provided.

3. Keep the unit away from radiators and other heat sources.

4. Avoid use near strong magnetic fields.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

The symbol for CLASS II (Double Insulation)

5. Do not push objects of any kind into the unit through the cabinet slots or openings as they could touch electrically live parts or short circuit parts resulting in a fire or electric shock.

6. To prevent fire or shock hazard, do not expose this apparatus to dripping or splashing, no objects filled with liquids, such as vases, should be placed on the apparatus.

7. Do not stand the unit vertically. Use the unit in a horizontal (flat) position only.

8. Before attempting to operate the unit, make sure that the timer recording mode is off.

9. This product is in Stand-by mode when turned off while the mains cable is connected.

The front panel display will not light up. This is a Power Saving Mode (ECO) for standby.

10. Do not place any combustible objects on the device (candles, etc.).

11. Before moving the unit, be sure to remove any media and unplug the mains cable from the AC outlet.

12. Disconnect the mains plug to shut off the unit, if you suspect a fault has developed, or if it will not be used for an extended period.

13. The mains plug shall remain readily operable.

14. Read the instruction manual, and QSG to ensure correct and safe installation and interconnection of the unit in multimedia systems.

15. Keep a distance of 20 cm around the ventilation openings of the apparatus.

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.

This product consists of materials which can be recycled and reused if disassembled by a specialised company.

E9TK4BD_EN.book Page 3 Wednesday, January 6, 2010 10:05 PM

Following information is only for EU-member states:

The use of the symbol indicates that this product may not be treated as household waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Following information is only valid EU-member States: Disposal of batteries and/or accumulators

The crossed out wheeled dust bin symbol indicates that batteries and/or accumulators must be collected and disposed of separately from household waste or accumulator contains more than the specified values of lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery Directive (2006/66/EC), then the chemical symbols for lead (Pb), mercury (Hg) and/or cadmium (Cd) will appear below the crossed out wheeled dust bin symbol. By participating in separate collection of batteries, you will help to assure the proper disposal of products and batteries and thus help to prevent potential negative consequences for the environment and human health. For more detailed information about the collection and recycling programmes available in your country, please contact your local city office or the shop where you purchased the product.

Make your contribution to the environment!!!

• Exhausted batteries do not belong in the dustbin.

• You can dispose of them at a collection point for exhausted batteries or special waste.

• Contact your council for details.

Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing or climbing on it. A falling unit can cause serious injury or even death.

. If the battery

Pb, Hg, Cd

Connection to Power

Before Switching on make sure that the voltage of your electricity supply is the same as that indicated on the rating plate.

Mains Cord

This appliance may be fitted with a non-rewireable plug. If it is necessary to change the fuse in a nonrewireable plug the fuse cover must be refitted. Do not use the plug if the fuse cover is lost or damaged. If a replacement fuse cover cannot be found, the plug must be changed with another carrying the same value fuse. It is important that the colour of the replacement fuse cover corresponds with the rating marking on the base of the plug. If the plug has to be changed because it is not suitable for your socket, or becomes damaged, it should be cut off and an appropriate plug fitted following the wiring instructions below. The plug removed must be disposed of safely as insertion into a 13A socket is likely to cause an electrical hazard. For your own safety read the following instructions carefully before attempting to connect this unit to mains. The wires in this mains lead are coloured in accordance with the following code:

BLUE=NEUTRAL, BROWN=LIVE

Important

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. No connection is to be made to the earth terminal of the plug. If a 13 Amp (BS 1363) Plug is used, a 5 Amp Fuse must be fitted, or if any other type of Plug is used a 3 or 5 Amp Fuse must be fitted, either in the Plug or Adaptor, or on the Distribution Board.

Mains Supply: 220 - 240 V~ 50 Hz - AC only Do not make any connection to the larger pin marked with the

letter “E” or by the symbol or coloured green or green and yellow.

FUSE

BROWN

BLUE

(Neutral)

OUTER SHEATH OF THE WIRE

(Live)

CORD GRIP

Installation Location

For safety and optimum performance of this unit:

• Install the unit in a horizontal and stable position.

• Keep the unit away from electronic equipment such as an amplifier, TV, etc. to prevent warping,damage, fire and malfunction.

• Do not place anything directly on top of the unit.

• Shield the unit from direct sunlight and keep away from sources of intense heat. Avoid dusty or humid locations. Avoid locations with insufficient ventilation for suitable heat dissipation. Do not block the ventilation holes on the sides of the unit. Avoid locations subject to strong vibration or strong magnetic fields.

Avoid the Hazards of Electrical Shock and Fire

• Do not handle the mains cable with wet hands.

• Do not pull on the mains cable to disconnect it from the AC outlet. Grasp it by the plug.

• If, by accident, water is spilled on the unit, unplug the mains cable immediately and take the unit to an authorised service centre for servicing.

Moisture Condensation Warning

Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, after heating a cold room, or under conditions of high humidity. Do not use the unit for at least 2 hours to allow the inside to dry.

About Copyright

Unauthorised copying, broadcasting, public performance and lending of discs are prohibited. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorised by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorised by Macrovision. Reverse engineering or disassembly is prohibited.

Introduction Connections

TV View Operation

Basic Setup /

Playback Editing OthersFunction SetupRecording VCR Functions

10_Intro.fm Page 4 Friday, January 8, 2010 4:40 PM

Notice for the Progressive Scan Outputs

Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of picture problems with 480 or 576 progressive scan output, it is recommended that the user switch the connection to the ‘standard definition’ output. If there are questions regarding your TV set compatibility with this 480p or 576p product, please contact our customer service centre.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

Digital Recording enables consumers to record

“Dolby high-quality video with stereo sound on recordable DVD discs. The technology, when utilised instead of PCM recording, also saves recordable disc space, allowing for higher video resolution or extended recording time on each DVD. DVDs created using Dolby Digital Recording will play back on all DVD-Video players.” Note: This is true when the players are compatible with

actual recordable DVD discs.

Manufactured under license under U.S. Patent #: 5,451,942 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks and DTS Digital Out and the DTS logos are trademarks of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

DivX®, DivX Certified® and associated logos are registered trademarks of DivX, Inc. and are used under license.

DVB is a registered trademark of the DVB Project

EU Conformity Statement

“This product is marked with “CE” and complies therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC and ErP Directive 2009/125/EC(2005/32/EC).”

Responsible for CE-marking is TOSHIBA INFORMATION SYSTEMS (U.K.) LTD, Toshiba Court, Weybridge Business Park, Addlestone Road, Weybridge, Surrey, KT15 2UL, United Kingdom

MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.

THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD (“MPEG-4 VIDEO”) AND/OR (ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL, INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, L. L. C. SEE HTTP://WWW.MPEGLA.COM

Maintenance

CLEANING THE UNIT

Use a soft cloth slightly moistened with a mild detergent solution. Do not use solutions containing alcohol, spirits, ammonia or abrasives.

CLEANING DISCS

If a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the centre out. Do not wipe in a circular motion. Do not use solvents such as benzine, thinners, commercially available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for analogue records.

DISC HANDLING

Handle the discs so that fingerprints and dust do not adhere to the disc surfaces. Always store the disc in its protective case when it is not in use.

SERVICING

If the unit becomes inoperative, do not try to correct the problem by yourself. There are no user serviceable parts inside. Turn the unit off, unplug the mains cable, and consult your dealer or an authorised service centre.

CLEANING THE DISC LENS

If the unit does not perform correctly even though you have referred to “Troubleshooting” and the relevant sections in the Owner’s Manual, the laser optical pickup unit may be dirty. Consult your dealer or an authorised service centre for inspection and cleaning of the laser optical pickup unit.

AUTO HEAD CLEANING

• Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture.

• Playback picture may become blurred or interrupted while the TV programme reception is clear. Dirt accumulated on the video heads after a long period of use, or the usage of rental or worn tapes can cause this problem. If a streaky or snowy picture appears during playback, the video heads in the unit may need to be cleaned.

1 Please visit your local Audio / Video store and purchase a

good quality VCR Video Head Cleaner.

2 If a Video Head Cleaner does not solve the problem,

please consult your dealer or an authorised service centre.

Note

• Remember to read the instructions along with the video head cleaner before use.

• Clean video heads only when problems occur.

E9TK4BD_EN.book Page 5 Wednesday, January 6, 2010 10:05 PM

Accessories Supplied

• Remote control with 2 R6 (1.5 V) batteries

•RF cable

• Owner’s Manual

• Quick Setup Guide

• Helpline Sheet

Features

The following features are available with this unit.

Recording

DVD VCR

• Recording up to 12 programmes

• One-touch timer recording:

(DVD) [E Page 32] (VCR) [E Page 71]

•PDC: [E Page 34]

DVD

• Automatic chapter mark setting: [E Page 31]

• Automatic Playlist making (VR mode DVD-RW discs only)

• Automatic finalising (video mode DVD-RW/-R, DVD+R discs only): [E Page 42]

• Automatic title menu making (video, +VR mode only):

[E Page 42]

Dubbing

DVD VCR

• DV dubbing: (DVD) [E Pages 39-40] (VCR) [E Page 71]

• Dubbing mode: [E Page 41]

Playback

DVD

• Theatre surround sound: [E Page 19]

• Quick search: [E Pages 51-52]

• Playback from Original or a Playlist (VR mode DVD-RW

discs only): [E Page 43]

• Virtual Surround System: [E Page 54]

• Playing back data files recorded in a USB device:

[E Page 45]

• Chasing playback during recording and simultaneous

playback and recording: [E Page 50]

• Playing back MP3 / JPEG / DivX

VCR

• Quick search: [E Pages 71-72]

files: [E Pages 44-46]

Editing

DVD

• Adding or deleting chapter marks manually:

[E Page 57]

• Creating titles to a Playlist (VR mode DVD-RW discs

only): [E Page 59]

• Deleting titles: [E Page 56]

• Deleting a scene of a title (VR mode DVD-RW discs

only): [E Page 60]

• Editing title name: [E Page 57]

• Combining titles (VR mode DVD-RW discs only):

[E Page 59]

• Dividing titles (VR mode DVD-RW, DVD+RW discs only):

[E Page 59]

• Protecting titles (VR mode DVD-RW discs only):

[E Page 58]

• Adding or deleting chapter marks at once

(video mode DVD-RW discs only): [E Page 58]

• Hiding chapters (+VR mode only): [E Page 58]

Compatibility

Introduction Connections

TV View Operation

Basic Setup /

Playback Editing OthersFunction SetupRecording VCR Functions

DVD

• Playing back discs recorded in video mode in any

regular DVD player: [E Page 42]

Others

DVD

• Progressive scan system: [E Pages 17, 67]

• HDMI (High-Definition Multimedia Interface):

[E Pages 18, 68]

E9TK4BD_EN.book Page 6 Wednesday, January 6, 2010 10:05 PM

Table of Contents

Introduction ...................................................... 2

Precautions ........................................................................ 2

Features ............................................................................. 5

Guide to the Owner’s Manual............................................. 7

Functional Overview......................................................... 10

Installing Batteries in the Remote Control ........................ 12

Switching DVD / VCR mode............................................. 12

Guide to On-Screen Displays........................................... 13

Front Panel Display Guide................................................ 16

Connections ................................................... 17

Connecting to a TV........................................................... 17

Connecting to External Equipment................................... 19

Digital Audio for Better Sound Quality.............................. 19

Basic Setup / TV View Operation .................. 20

Initial Setting..................................................................... 20

Channel Setting................................................................ 20

TV View Operation ...........................................................23

Recording........................................................ 28

Information on DVD Recording......................................... 28

Formatting a Disc .............................................................30

Selecting the Audio Mode ................................................ 31

Basic Recording and One-touch

Timer Recording (OTR) .................................................32

Timer Recording............................................................... 33

Timer Recording (EPG).................................................... 36

Series Link Timer Recording ............................................ 37

Satellite Link ..................................................................... 37

Settings for External Equipment....................................... 38

Information on DV Dubbing .............................................. 39

DVC to DVD Dubbing .......................................................40

Dubbing Mode .................................................................. 41

Setting a Disc to Protect................................................... 42

Finalising Discs ................................................................ 42

Editing ............................................................. 55

Guide to a Title List .......................................................... 55

Editing Discs .................................................................... 56

Function Setup ............................................... 61

General Setting ................................................................ 63

VCR Functions................................................ 70

Playback........................................................................... 70

Basic Recording and One-touch

Timer Recording (OTR) ................................................. 70

Search.............................................................................. 71

Other Operations.............................................................. 72

Hi-Fi Stereo Sound System ............................................. 72

Others .............................................................. 73

Troubleshooting................................................................ 73

Troubleshooting for Error Messages ................................ 76

Language Code ............................................................... 78

Specifications................................................................... 79

Playback.......................................................... 43

Basic Playback ................................................................. 43

PBC Function for Video CDs............................................ 47

Special Playback .............................................................. 48

Search .............................................................................. 51

Repeat / Random / Programme Playback / Slide Show... 52

Selecting the Format of Audio and Video......................... 53

DVD-V

DVD-RW

DVD-R

DVD+RW

DVD+R

VCD

MP3

JPEG

DivX

VCR

E9TK4BD_EN.book Page 7 Wednesday, January 6, 2010 10:05 PM

Guide to the Owner’s Manual

Symbols Used in the Owner’s Manual

To show what recording mode or media type applies to each function, the following symbols appear at the beginning of each operating item.

Symbol Description

DVD-V

Video

DVD-RW

Available to DVD-videos

Available to DVD-RW discs in video mode

Available to DVD-RW discs in VR mode

Introduction Connections

TV View Operation

Basic Setup /

DVD-R

DVD+RW

DVD+R

CDCDCD

VCD

MP3

JPEG

DivX

VCR

Available to DVD-R discs in video mode

Available to DVD+RW discs

Available to DVD+R discs

Available to audio CDs

Available to video CDs

Available to CD-RW/-R discs and USB device with MP3 files

Available to CD-RW/-R discs and USB device with JPEG files

Available to DVD-RW/-R, DVD+RW/+R, CD-RW/-R discs and USB device with DivX

files in USB device are not guaranteed.)

(DivX

Available to VHS tapes Use only cassettes marked VHS ( )

files

PAL

Symbols for Tuner Setting and Recording

The following is the description for the symbols for tuner setting used in this manual.

ANALOG : Settings only for the analogue mode

DVB : Settings only for the DVB mode

Playback Editing OthersFunction SetupRecording VCR Functions

DVD-RW

DVD-R

DVD+RW

DVD+R

E9TK4BD_EN.book Page 8 Wednesday, January 6, 2010 10:05 PM

Discs for Recording / Playing

Disc Type DVD -RW DVD -R DVD +RW DVD+ R

Logo

Format Can be formatted in VR or video mode

Video Mode VR Mode

Icon

Maximum Record Time

Recordable/Playable

Recording Features

Record TV Programmes

Reuse by Deleting the Current Contents

Available Features

Record 16:9 Size Pictures

Record Copy-once Programmes

Create Chapters at Fixed Intervals (auto chapter)

Editing Features

Scene Delete

Edit Title Name

Create Chapters Wherever You Like (chapter mark)

Divide a Title

Combine Titles

Hide Chapters

Delete a Title

Create a Playlist

Protect a Title

✔: Available Grey: Not available * CPRM compatible disc only.

Versions

Compatibility

1×-6× Ver. 1.1/1.2 Ver. 1.1/1.2 CPRM compatible

Playable on most DVD players. Finalisation necessary. (Title menu will be created)

Video

DVD-RW

480 min (12 cm)

144 min (8 cm)

DVD-RW

480 min (12 cm)

144 min (8 cm)

Playable only on VR mode compatible unit. Finalisation recommended.

✔ ✔ ✔✔✔

✔✔ ✔

✔✔✔

✔*

✔ ✔ ✔✔✔

Playlist Original

✔✔

✔✔✔✔ ✔ ✔

✔✔ ✔✔

✔ ✔

✔

✔✔✔✔ ✔ ✔

Automatically formatted in video mode

DVD-R

DVD-R DVD+RW

480 min (12 cm)

144 min (8 cm)

1×-16× Ver. 2.0/2.1

Playable on most DVD players . Finalisation necessary. (Title menu will be created)

Automatically formatted in +VR mode

Autom atically formatted in +VR mode

DVD+RW DVD+R

480 min (12 cm)

144 min (8 cm)

1×-4× 1×-16×

Playable on DVD +RW compatible players. Finalisation recommended. (Title menu will be created)

480 min (12 cm)

144 min (8 cm)

Playable on most DVD players. Finalisation recommended. (Title menu will be created)

DVD+R

✔✔

✔ ✔

DVD players with are capable of playing DVD-RW recorded in VR mode.

DVD-V

VCD

MP3

JPEG

DivX

E9TK4BD_EN.book Page 9 Wednesday, January 6, 2010 10:05 PM

Discs for Playing

Disc Type DVD-VIDEO CD-DA Video CD CD-RW CD-R

Logo

Icon

Type of title MP3 JPEG DivX

Icon

Media

is a trademark of DVD Format/Logo Licensing Corporation.

• ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX,Inc. This is an official DivX Certified device that plays DivX video. Visit www.divx.com for more information and software tools to convert your files into DivX video.

• ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified device must be registered in order to play DivX Video-onDemand (VOD) content. To generate the registration code, locate the DivX VOD section in the device setup menu. Go to vod.divx.com with this code to complete the registration process and learn more about DivX VOD.

• DivX Certified content.

• Media containing the DivX Motion Compensation) playback feature, which is DivX supplemental function, cannot be played back on this unit.

Unplayable Discs

The following discs will not play back on this unit.

• CD-ROM • Compact Disc-Interactive

• Video Single Disc (VSD) • DVD-ROM

• DVD-audio • Unfinalised disc

• DVD or CD contains Windows Media™ Audio files

• DVD-RW/-R recorded in non compatible recording format

•Blu-ray Disc •HD DVD

On the following disc, the sound may not be heard.

• Super audio CD - Only the sound on the CD layer can be heard. The sound on the high-density super audio CD layer cannot be heard.

DVD-V

DVD-V CDCDCD VCD

Files for Playing

MP3

CD-RW/-R

USB device

to play DivX® video, including premium

files with the DivX®GMC (Global

JPEG

CD-RW/-R

USB device

(CD-I)

VCD CDCDCD CDCDCD

DivX

CD-RW/-R

DVD -RW/- R

DVD +RW/+ R

USB device (not guaranteed)

Following discs are recommended for good recording quality and are proven to be compatible with this unit. However, depending on the media condition the unit may not read the disc properly.

Verbatim DVD+R 8x, DVD+RW 4x, DVD-R 8x, DVD-RW 2x

JVC DVD-RW 4x Maxell DVD+R 4x/8x/16x, DVD-R 8x/16x SONY DVD+R 4x/8x/16x, DVD+RW 4x TDK DVD+R 4x/8x/16x

Performance of any other discs are not guaranteed.

• Toshiba is not liable for any damage or loss caused directly or indirectly by the malfunction of this unit,

including, without limitation, any one of the following:

• Failure to record contents intended to be recorded by the consumer.

• Failure to edit contents as intended by the consumer.

• When a DVD-RW/-R, DVD+RW/+R disc created on this unit is used (e.g., insertion, playback, recording or editing) in another DVD player, recorder or personal computer drive.

• When a DVD-RW/-R, DVD+RW/+R disc that is used in the manner described in the immediately preceding bullet point is used again in this unit.

• When a DVD-RW/-R, DVD+RW/+R disc that was recorded in another DVD recorder, or in a personal computer drive is used in this unit.

• Some functions may not work with personal computer discs.

• Discs recorded in this unit may not operate as expected on other DVD players, recorders or personal computer drives.

Introduction Connections

TV View Operation

Basic Setup /

Playback Editing OthersFunction SetupRecording VCR Functions

Colour Systems

This unit uses the PAL system. However, it is also possible to play back DVDs using other colour systems, such as NTSC.

Region Codes

This unit has been designed to play DVD with region 2. If these region symbols do not appear on your DVD, you cannot play back the DVD in this unit. The number inside the globe refers to region of the world.

Because of problems and errors that can occur during the creation of DVD and CD software and/or the manufacture of DVD and CD discs, Toshiba cannot guarantee that product will play every feature of every DVD bearing the DVD logo and/or every CD bearing the CD logo. As one of the creators of DVD technology, Toshiba DVD players are manufactured using the highest standards of quality, and as a result, such incompatibilities are rare.

E9TK4BD_EN.book Page 10 Wednesday, January 6, 2010 10:05 PM

Functional Overview

Front Panel

18 16 11 9

You can also turn on the unit by pressing these buttons. You can turn on the unit by pressing these buttons only when a videotape is in this unit. Press to turn on the unit, or to turn the unit into the standby mode. (To completely shut down the unit, you must unplug the

AC power cord.)

1 B ON\STANDBY button*

VCR

1517

14 13 12 10 8

2 Cassette compartment

3 A OPEN\CLOSE button*

(DVD) 4 VCR/DVD indicators 5 Disc tray 6 DV IN jack (AV3) 7 USB input jack 8 I REC button (DVD)

9PLAYB button*

(DVD)

10 STOP C button (DVD)

PROGRAM

DUBBING

DVDVCR

DVD

VCR

SELECT

DVD

USB

DV IN

7 6

12 DUBBING button 13 PROGRAM G\H buttons 14 Display (“Off” in standby) 15 Infrared sensor window 16 I REC button (VCR) 17 PLAY B button* 18 STOP/EJECT C / A button (VCR) 19 FWD D button* 20 REV E button* 21 Power indicator

(VCR)

11 SELECT button

Button names described in the Owner’s Manual

The instructions in this manual are described mainly with the operations using the remote control. Some operations can be carried out using the buttons on the front panel.

Rear Panel

1 3 456 87 92

1 Mains cable 2 HDMI OUT jack 3 DIGITAL AUDIO OUT (COAXIAL) jack 4 AUDIO OUT (L\R) jacks

Note

• Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit.

• After turning off the unit, leave the mains cable plugged for about one minute. Otherwise it may cause data loss or the unit may

not work properly.

• This unit does not have an RF modulator.

5 COMPONENT VIDEO OUT jacks 6 AV2 (DECODER) socket 7 AV1 (TV) socket 8 ANTENNA IN 9 ANTENNA OUT

E9TK4BD_EN.book Page 11 Wednesday, January 6, 2010 10:05 PM

Remote Control

1 2

5 6

11 12

15 16

17 18

23 24

25 26

30 31

32 33

35 36

1 OPEN\CLOSE A button 2 INPUT SELECT F button 3 Number buttons 4 SETUP button 5 TEXT button 6 VCR button 7 TOP MENU button (DVD) 8 Direction 9 DISPLAY button 10 RED/GREEN/YELLOW/BLUE button

SEARCH (BLUE) button (VCR)

11 REV E button 12 PLAY B button 13 SKIP H button (DVD) 14 PAUSE F button 15 TIME SLIP button (DVD) 16 DUBBING button 17 SUBTITLE button 18 AD (Audio Description) button 19 HDMI button 20 B ON/STANDBY button 21 PROG. G\H buttons 22 TIMER PROG. button 23 INFO C button 24 CLEAR button 25 GUIDE button 26 DVD button 27 DISC MENU button (DVD) 28 ENTER/OK button 29 RETURN/BACK button 30 FWD D button 31 STOP C button 32 SKIP G button (DVD) 33 INSTANT SKIP button (DVD) 34 SAT.LINK button 35 REC I button 36 REC MODE button 37 TIMER SET button 38 AUDIO D button

Button names described in the Owner’s Manual

The instructions in this manual are described mainly with the operations using the remote control. Some operations can be carried out using the buttons on the front panel.

K / L / 0 / 1 buttons

Introduction Connections

TV View Operation

Basic Setup /

Playback Editing OthersFunction SetupRecording VCR Functions

Note

• If you turn off this unit, [OPEN\CLOSE A] on the remote control is not available. Be sure to use [A OPEN\CLOSE] or [STOP\EJECT C \ A] on the unit.

E9TK4BD_EN.book Page 12 Wednesday, January 6, 2010 10:05 PM

Installing Batteries in the Remote Control

Install 2 R6 (1.5 V) batteries (supplied) into the remote control, carefully match with the polarity indicated inside the battery compartment.

21 3

Caution

• Incorrect use of batteries can result in hazards such as leakage and bursting.

• Do not mix new and old batteries together.

• Do not use different kinds of batteries together.

• Make sure that the plus (+) and minus (–) ends of each battery match the indications inside the battery compartment.

• Remove batteries if the equipment will not be used for a month or more.

• When disposing used batteries, please comply with governmental regulations or the public instructions for environmental protection that apply in your country or area.

• Do not recharge, short-circuit, heat, burn or disassemble batteries.

Switching DVD / VCR mode

You must select which component you want to operate first. Press [DVD] or [VCR] on the remote control or the front panel.

indicator

button

VCR

Device select indicators

DVD

Press [DVD] on the remote control.

VCR

Press [VCR] on the remote control.

SELECT

VCR DVD

PROGRAM

SELECT

DUBBING

VCR button

DVD button

DVDVCR

DVD

USB

DV IN

About the Remote Control

• Make sure there is no obstacle between the remote control and the remote control sensor on the unit.

• Use within the operating range and angle as shown.

DVD

VCR

7 m (30°)

7 m (30°)7 m

• The maximum operable range as follows:

Line of sight: approximately 7 m Either side of centre: approximately 7 m within 30 degrees

• Remote control operation may become unreliable if the remote control sensor of the unit is being exposed by the strong sunlight or fluorescent light.

• Remote controls for different devices can interfere with each other. Be careful when using remote controls for other equipment located close to the unit.

• Replace the batteries when the operating range of the remote control reduces.

Within about 7 m

Note

• You can also press [SELECT] on the front panel to switch between DVD and VCR mode.

5 6

E9TK4BD_EN.book Page 13 Wednesday, January 6, 2010 10:05 PM

Guide to On-Screen Displays

DISPLAY Menu

DVD

Press [DVD] first.

With a disc inserted into the unit, press [DISPLAY] to display the on-screen display. The on-screen display shows information about what is recorded on the disc.

1/ 5 1/ 5

T C

This is an example screen for explanation. Displayed items vary depending on the actual mode.

1 Indicates a disc type and format mode. 2 Indicates a type of titles for VR mode DVD-RW

disc.

3 Indicates a channel number, station name

(analogue channel only) or selected external input mode.

4 Indicates a recording mode and possible

recording time left.

5 Indicates the current title number/total number

of titles, the current chapter number/total number of chapters, and time lapse of the current title playback/total duration of the title.

6 Each icon means:

: Search

: Audio

: Subtitle

: Angle

: Repeat

: Marker

: Noise Reduction

: Zoom

: Surround

R W VR ORG

1 BBC1

SP 1:53

8 2 2 2

Press [DISPLAY] repeatedly while the display menu is displayed to display the following information.

Title name information

Title Name

My Title

(only when DVD+RW/+R, VR mode DVD-RW or unfinalised video mode DVD-RW/-R disc is in playback)

File name information

&ILE.AME

-Y&ILE

(only when MP3/JPEG/DivX playback)

(only when MP3 file is in playback)

Title name information

4ITLE.AME

Artist name information

!RTIST.AME

Album name information

!LBUM.AME



6IDEO)NFO !UDIO)NFO"ITSTREAM

(only for the images output through the HDMI output)

P





files is in





9#B#R

1 Indicates the resolution of the HDMI output

image. 2 Indicates the HDMI video format. 3 Indicates the HDMI audio format.

• “- - -” will be displayed, when it does not have any

information.

Introduction Connections

TV View Operation

Basic Setup /

Playback Editing OthersFunction SetupRecording VCR Functions

E9TK4BD_EN.book Page 14 Wednesday, January 6, 2010 10:05 PM

VCR

While in the VCR mode, the on screen display of the VCR mode is displayed. Press [VCR] first. Press [DISPLAY] to display the on screen display.

12:00

AV2

STEREO

0:00:00 STEREO

This is an example screen for explanation. Displayed items are depending on the actual mode.

1 Current time 2Position number 3 Audio status of the receiving broadcast or

external equipment

4 Audio status of the currently playing back

videotape 5 Tape counter 6 Recording or playing back speed 7 Status of the current tape

INFO Menu

DVB

Press [INFO C] while viewing a DVB programme to display the programme information.

13 Channel 4+1

English

NOW:

6 5

Castle Stereo AD Sub Entertainment 27 min left NEXT:

Burning Questions

1 Audio language 2 Channel number 3 Channel name 4 Current time and day 5 Next programme information 6 Current programme information

The window will automatically exit after 4 seconds, or press [RETURN/BACK] to exit. While the window appears, press [INFO C] again to display more information. Press [RETURN/BACK] to exit.

11:53 Mon

11:23 – 12:20

12:20 – 12:25

Main Menu

Press [SETUP] to display the main menu. Then use [K \ L] to select a menu and press [ENTER\OK] to display the sub menu. Press [RETURN/BACK] to return to previous screen.

Setup

• E is displayed when a disc with CD-DA/VCD/MP3/JPEG is

inserted.

• F is displayed when a USB flash memory with MP3/JPEG

is plugged.

A General Setting

1 2 3 4 5 6 7 8 9

1 Playback: [E Page 64] 2Display: [E Page 66] 3Video: [E Page 67] 4 Recording: [E Pages 30-32, 38, 41, 42] 5Clock: [E Page 67] 6Channel: [E Pages 20-26] 7DivX: [E Pages 46, 68] 8 HDMI: [E Page 68] 9 DVB Setting: [E Page 69] 10 Reset All: [E Page 69]

DVB Setting

General Setting

Playback Display Video Recording Clock Channel DivX HDMI DVB Setting Reset All

General Setting

Timer Programming

Title List

DVD Menu

DISC Playback Mode

USB Playback Mode

General Setting

Playback Display Video Recording Clock Channel DivX HDMI DVB Setting Reset All

Adult Lock Language About

Parental Lock Audio Out Disc Menu Language Audio Language Subtitle Language Angle Icon Still Mode TV System

1 2

1 Adult Lock: [E Page 69] 2Language: [E Page 69] 3 About: [E Page 69]

E9TK4BD_EN.book Page 15 Wednesday, January 6, 2010 10:05 PM

B Timer Programming

To programme a timer recording. [E Page 33]

C Title List

To call up the title list. [E Page 55]

D DVD Menu

1 2 3 4

DVD Menu

Format Finalise Disc Protect OFF ON Delete All Playlists

1 Format (DVD-RW, DVD+RW only):

[E Pages 30, 31]

2Finalise: [E Page 42] 3 Disc Protect (VR mode DVD-RW, DVD+RW/+R

disc only):

[E Page 42]

4 Delete All Playlists (VR mode DVD-RW disc

only):

[E Page 60]

E DISC Playback Mode

Audio CD / video CD

1 2 3

DISC Playback Mode

Random Play Programme Play PBC (Video CD only)

1Random Play: [E Page 52] 2 Programme Play: [E Page 53] 3 PBC (Video CD only): [E Page 48]

CD-RW/-R with MP3 / JPEG files

4 5 1

DISC Playback Mode

Music Photo

Random Play Slide Show

4 Music (MP3 files): [E Page 52] 5 Photo (JPEG files): [E Pages 52, 53] 6Slide Show: [E Page 53]

F USB Playback Mode

USB Playback Mode

Music

Photo

Random Play Slide Show

Introduction Connections

TV View Operation

Basic Setup /

Playback Editing OthersFunction SetupRecording VCR Functions

1 Music (MP3 files): [E Page 52] 2 Photo (JPEG files): [E Pages 52, 53]

E9TK4BD_EN.book Page 16 Wednesday, January 6, 2010 10:05 PM

Front Panel Display Guide

DTV

1 DTV indicator

: Appears when the channel is in digital mode.

2 Title / Track and Chapter number

: Title / track number : Chapter number

3 Current status of the unit

F: Appears when a tape or disc playback is paused.

Appears during step by step playback.

B: Appears when playing back a tape or disc. F B: Appears during slow forward / reverse playback.

: Appears when the timer programming or One-

touch Timer Recording (OTR) is set and operating. Appears when the unit goes into the satellite link standby or recording mode. Flashes when satellite recording was not executed because of some error.

I: Appears during recording.

Flashes when recording being paused.

: Appears when a videotape is in this unit.

VCR

DVD

: Appears when a disc is in this unit.

: Appears during dubbing.

:Appears when this unit is in DVD output mode, or

DVD

the timer-standby mode for DVD recording.

:Appears when this unit is in VCR output mode, or

the timer-standby mode for VCR recording.

4 Displays the following

• Playing back time

• Current title / chapter / track / file number

• Recording time / remaining time

•Clock

• Channel number

• One-touch Timer Recording (OTR) remaining time

• Selected HDMI video resolution

Note

• Except when satellite recording is in standby, front panel display stays off while the unit is in power off / timer-standby mode.

This is a new Power Save (ECO) feature.

Display Messages

The disc tray is opening.

DVD

The PBC function of the video CD is activated.

DVD

The disc tray is closing.

DVD

A disc is loading.

DVD

Data is being recorded on a disc.

DVD

Appears when the satellite link recording is in standby.

DVD

Appears when HDMI video resolution (480p) is

DVD

selected.

Appears when HDMI video resolution (576p) is

DVD

selected.

Appears when HDMI video resolution (720p) is

DVD

selected.

Appears when HDMI video resolution (1080i) is

DVD

selected.

Appears when HDMI video resolution (1080p) is

DVD

selected.

E9TK4BD_EN.book Page 17 Wednesday, January 6, 2010 10:05 PM

Connections

Connecting to a TV

Connect the unit to a TV after considering the capabilities of your existing equipment.

Before installation, unplug your TV and this unit

Cable Signal

Connect the antenna or cable to the ANTENNA IN jack of this unit.

Connect the ANTENNA OUT jack of this unit to the Aerial jack of your TV.

Antenna

RF cable (not supplied)

To A e r i al j a c k

RF cable (supplied)

• Analogue teletext can only be output in VCR mode through AV1 (TV) out. Use TV remote control to decode the analogue teletext.

• When changing the “Video Out” setting (“SCART (RGB)”, “Component (Interlace)” or “Component (Progressive)”), connect to the corresponding jack on the TV. If the setting is changed, for example, to “Component (Interlace)” or “Component (Progressive)” while the scart cable is connected to the TV, a distorted video signal may be output.

Using the COMPONENT VIDEO OUT Jacks and the AUDIO OUT (L\R) Jacks

If your TV has component video input jacks, use a component video cable (to connect the COMPONENT VIDEO OUT jacks) and an audio cable (to connect the AUDIO OUT (L\R) jacks). When using this type of connection, “Video Out” setting should be set to “Component (Progressive)” or “Component (Interlace)”. Refer to “Video Out” on page 67.

• Component connection provides the better quality picture.

Component

video IN

YPB/CB PR/CR

Audio cable

(not supplied)

Audio IN

Component

video cable

(not supplied)

Introduction Connections Playback Editing OthersFunction SetupRecording VCR Functions

TV View Operation

Basic Setup /

Using the Scart socket

Audio/video cable (not supplied)

Scart/RCA cable (not supplied)

Scart adaptor (not supplied)

Connect AV1 (TV) Scart socket of this unit to the Scart socket of your TV.

Note

• If your TV does not have a Scart socket, use a Scart/RCA cable to connect.

• Connect this unit directly to the TV. If the AV cables are connected to a VCR, pictures may be distorted due to the copy protection system.

Scart cable (not supplied)

Connect the COMPONENT VIDEO OUT jacks of

this unit to the component video input jacks of your TV.

Connect the AUDIO OUT (L\R) jacks of this unit

to the analogue audio input jacks of your TV.

• After you have made the connections, set the “Video Out” setting. (See page 67.)

Selecting Progressive Scan (576p/480p or Interlaced 576i/480i) Playback

• If your TV is compatible with progressive scanning (576p/ 480p), connect the TV to the COMPONENT VIDEO OUT jacks of this unit and set “Video Out” setting to “Component (Progressive)” in “Setup” menu. (See page 67.) Next, set your TV to the progressive scan mode.

• If your TV is not compatible with progressive scan, set “Video Out” setting to “Component (Interlace)”.

• Use a commercially available adaptor if the video input jacks of your TVs or monitors are the BNC type.

• Only component and HDMI connections are compatible with the Progressive Scan.

E9TK4BD_EN.book Page 18 Wednesday, January 6, 2010 10:05 PM

Using an HDMI Compatible Port

[HDMI CONNECTION]

• HDMI outputs the video / audio signals without converting to analogue signals.

• No audio connections is required.

• Use the HDMI cable (commercially available) for connection.

• Connect the HDMI output jack of this unit to the HDMI input jack of TV.

HDMI cable (not supplied)

To HDMI input jack

HDMI IN

this unit

Selecting HDMI video resolution

Press [HDMI] to select the HDMI video resolution. The video resolution changes as follows every time [HDMI] is pressed. 576p (PAL) / 480p (NTSC) J 720p J 1080i J 1080p (An HDMI video resolution that is not supported by the display device will be skipped.)

Actual Output Modes by Media

Audio recording format of the disc

Dolby Digital

LPCM

DVD-video

DTS

MPEG

Dolby Digital

DivX

MP3

MP2

For audio CD, video CD and MP3 files, 2 channel PCM will be output regardless of the “Dolby Digital” setting. If the connected device is not compatible with HDMI BITSTREAM, audio will be output as PCM even if you select “Stream” in “Dolby Digital” setting. (See page 65.)

Dolby Digital / DTS / MPEG setting of this unit

PCM 2 channel PCM Stream Dolby Digital PCM Stream ON DTS

OFF PCM 2 channel PCM Stream MPEG PCM 2 channel PCM Stream Dolby Digital PCM Stream PCM 2 channel PCM Stream MPEG

Actual output

2 channel PCM

Note

• Because HDMI is an evolving technology, it is possible that some devices with an HDMI input may not operate properly with this unit.

• When using an HDCP-incompatible display device, the image will not be viewed properly.

• Among the devices that support HDMI, some devices can control other devices via the HDMI connector; however, this unit cannot be controlled by another device via the HDMI connector.

• The audio signals from the HDMI connector (including the sampling frequency, the number of channels and bit length) may be limited by the device that is connected.

• Among the monitors that support HDMI, some do not support audio output (for example, projectors). In connections with device such as this unit, audio signals are not output from the HDMI output connector.

• When this unit’s HDMI connector is connected to a DVI-D compatible monitor (HDCP compatible) with an HDMI-DVI conversion cable, the signals are output in digital RGB.

• If the connected equipment is not compatible with HDMI BITSTREAM, DTS sound will not be output.

• When the power failure occurs, or when you unplug the unit, some problems in the HDMI setting might occur. Please check and set the HDMI setting again.

To play back the digital video images of a DVD via an HDMI connection, it is necessary that both the player and the display device (or an AV amplifier) support a copyright protection system called HDCP (high-bandwidth digital content protection system). HDCP is copy protection technology that comprises data encryption and authentication of the connected AV device. This unit supports HDCP. Please read the operating instructions of your display device (or AV amplifier) for more information.

* HDMI: High Definition Multimedia Interface

E9TK4BD_EN.book Page 19 Wednesday, January 6, 2010 10:05 PM

Introduction Connections Playback Editing OthersFunction SetupRecording VCR Functions

Connecting to External Equipment

This unit has three input terminals. Press [INPUT SELECT F] repeatedly to select the external input mode, then press [PROG. G\H] repeatedly to select AV1, AV2 or DV(AV3). Be sure that all the units are switched off before making connections.

Recording from a DVD player, Satellite Box or other Audio-Video equipment with a Scart output socket (AV2)

AV output jack (Scart)

Scart cable (not supplied)

AV2 (DECODER)

Note

• When you record a TV programme from a Satellite Box / decoder, you must connect a Scart cable to AV2 (DECODER). (See page 37.)

• The signal from the external device will be output automatically when the TV is connected to AV1 and the external device is connected to AV2 using a Scart cable with its power on. (However, it will not be output when this unit’s power is turned off.) If you want to monitor this unit’s signal, press [DISPLAY] or turn the external device off. (The signal from this unit can only be monitored during playback.)

If you want to monitor the signal from other input, press [DISPLAY], then press [INPUT SELECT F] to select the

desired external input mode, then select the desired input channel using [PROG. G\H].

Recording from a DV-camcorder (DV(AV3))

When connecting a DV-camcorder, use DV input jack of DV(AV3) (Front).

DV(AV3) (Front)

DVDVCR

DUBBING

VCR DVD

SELECT

DVD

PROGRAM

Digital Audio for Better Sound Quality

Dolby Digital decoder, DTS decoder or MPEG decoder, etc.

Coaxial cable

(not supplied)

COAXIAL

The connections illustrated above are optional for better sound

For clear digital sound quality, use the DIGITAL AUDIO OUT (COAXIAL) jack to connect your digital audio equipment.

If the audio format of the digital output does not match the capabilities of your receiver, the receiver will produce a strong, distorted sound or no sound at all.

Connecting a Dolby Digital™ decoder, DTS decoder or MPEG decoder

• Connecting multi-channel Dolby Digital decoder allows you to enjoy the Multi-channel Dolby Digital surround system as well as DTS decoder, Multi-channel surround system.

• After connecting to a Dolby Digital decoder, set “Dolby Digital” to “Stream” in “Audio Out” menu. (See page 65.)

• After connecting to a DTS decoder, set “DTS” to “ON” in “Audio Out” menu. (See page 65.)

• After connecting to a MPEG decoder, set “MPEG” to “Stream” in “Audio Out” menu. (See page 65.)

Connecting to an MD deck or DAT deck

• The audio source recorded in Dolby Digital Multi-channel surround format cannot be recorded using an MD or DAT deck as a digital sound.

• If not connected to a Dolby Digital decoder, set “Dolby Digital” to “PCM” in “Audio Out” menu. Playing back a DVD using incorrect settings may generate noise distortion and damage speakers.

• Set “Dolby Digital” and “MPEG” to “PCM” and set “DTS” to “OFF” in “Audio Out” menu for connecting to an MD or DAT deck.

• You can use AUDIO OUT (L\R) jacks for the connection of your audio system.

Digital audio

input jack

COAXIAL

TV View Operation

Basic Setup /

USB

DV c abl e (4-pin)

(not supplied)

DV IN

DV OUT



&2)

#LOCK3ETTING

E9TK4BD_EN.book Page 20 Wednesday, January 6, 2010 10:05 PM

Basic Setup / TV View Operation

Also you can customize the memorised channel at “General Setting”.

Initial Setting

When you turn on this unit for the first time, you need to follow these steps.

1 Press [B ON\STANDBY]. 2 Turn the TV on. Select the input to which the

unit is connected.

3 Select your desired tuning type according to

your area using [K \ L], then press [ENTER\OK].

Auto Tuning

Make sure the antenna is connected to “ANTENNA IN” jack.

Digital tuning

Digital & Analog tuning

Analog tuning

The unit will start getting channels available in your area.

Refer to following pages for details.

• Refer to “Manual Tuning (ANALOG)” on page 21.

• Refer to “Manual Tuning (DVB)” on page 22.

• Refer to “Skip a Preset Channel” on page 22.

• Refer to “Move” on page 22.

Selecting the TV Aspect Ratio

Use this feature to adjust the aspect ratio of the video source which is different from your TV’s ratio to fit your TV monitor without distorting the picture.

1 In stop mode, press [SETUP]. Select “General

Setting” using [K \ L], then press [ENTER\OK].

2 Select “Video” using [K \ L], then press

[ENTER\OK].

3 Select “TV Aspect” using [K \ L], then press

[ENTER\OK].

Digital tuning:

Only the DVB channels receivable in your area are automatically scanned and memorised.

Digital & Analog tuning:

Both analogue and DVB channels receivable in your area are scanned and memorised automatically.

Analog tuning:

Only the analogue channels receivable in your area are automatically scanned and memorised.

• If no channel has been memorised, the antenna

confirmation display will appear. Press [ENTER\OK] to start auto scanning again or press [RETURN/BACK] to cancel the initial settings.

4 After finishing channel setting, “Clock Setting”

will appear.

• The current date and time will appear automatically.

•

If the current date and time are correct, press

[RETURN/BACK] [ENTER\OK]

page 67

Note

• After “Initial Setting”, if you need to unplug the mains cable, make sure to turn off the power first and leave it in standby mode for at least 1 minute before attempting to unplug. Otherwise, it may cause data loss.

If you want to set each item of “Initial Setting” again, you can set them at “General Setting”.

• Refer to “Auto Tuning (DVB & ANALOG)” on this page.

• Refer to “Auto Tuning (ANALOG)” on page 21.

• Refer to “Auto Tuning (DVB)” on page 22.

• Refer to “Clock” on page 67.

to exit, if they are incorrect, press

and follow to “A Clock Setting” on

TV Aspect Video Out

4 Select the desired option using [K \ L], then

press [ENTER\OK].

46!SPECT

,ETTER"OX 0AN3CAN 7IDE

5 Press [SETUP] to exit.

Note

If you have a standard TV:

• Select “4:3 Letter Box” for a full width picture with black bars at the top and bottom.

• Select “4:3 Pan & Scan” for a full height picture with both sides trimmed.

If you have a wide screen TV:

• Select “16:9 Wide”.

Channel Setting

You can retune this unit or edit the channel setting with following methods.

Auto Tuning (DVB & ANALOG)

DVB ANALOG

Programme the tuner to scan both analogue and DVB channels you can receive in your area.

1 In stop mode, press [SETUP]. Select “General

Setting” using [K \ L], then press [ENTER\OK].

“General Setting” menu will appear.

2 Select “Channel” using [K \ L], then press

[ENTER\OK].

E9TK4BD_EN.book Page 21 Wednesday, January 6, 2010 10:05 PM

3 Select “Auto Tuning (DVB & ANALOG)” using

[K \ L], then press [ENTER\OK].

The unit will start storing channels available in your area.

General Setting

Playback Display Video Recording Clock Channel DivX HDMI DVB Setting Reset All

Wait for several minutes to finish channel storing.

Auto Tuning (DVB & ANALOG) DVB Channel Setup ANALOG Channel Setup

4 Press [SETUP] to exit.

You can select only the channels memorised in this unit by using [PROG. G\H].

To cancel auto tuning

Press [SETUP] during scanning.

Note

• The number of TV channels you can get is different depends on your local area.

• If the auto tuning is cancelled during scanning, some channels not yet tuned may not be received.

Auto Tuning (ANALOG)

ANALOG

Programme the tuner to scan only the analogue channels you can receive in your area.

1 In stop mode, press [SETUP]. Select “General

Setting” using [K \ L], then press [ENTER\OK].

2 Select “Channel” using [K \ L], then press

[ENTER\OK].

3 Select “ANALOG Channel Setup” using [K \ L],

then press [ENTER\OK].

4 Select “Auto Tuning” using [K \ L], then press

[ENTER\OK].

The unit will start storing channels available in your area.

!.!,/'#HANNEL3ETUP

!UTO4UNING

-ANUAL4UNING

-OVE

Wait for several minutes to finish channel storing.

5 Press [SETUP] to exit.

You can select only the channels memorised in this unit by using [PROG. G\H].

• If you are using a satellite receiver, or a cable box, turn it on and select SKY NEWS before commencing tuning. If the SKY NEWS channel is not available to you, choose another channel that you can recognise easily, and move this reception to preset 6 after the automatic tuning has finished. Instructions on page 22 explain how to move channels.

Manual Tuning (ANALOG)

ANALOG

You can preset an analogue channel manually and individually.

1 In stop mode, press [SETUP]. Select “General

Setting” using [K \ L], then press [ENTER\OK].

2 Select “Channel” using [K \ L], then press

[ENTER\OK].

3 Select “ANALOG Channel Setup” using [K \ L],

then press [ENTER\OK].

4 Select “Manual Tuning” using [K \ L], then

press [ENTER\OK].

5 Select “Position” using [K \ L], then press [1].

Position Channel Decoder Skip

OFF

1 1

6 Select the position number you want to use

using [the Number buttons] or [K \ L], then press [0].

• You can select position number 1-99.

•With [the Number buttons], press “0” first to enter a single digit number.

7 Select “Channel” using [K \ L], then press [1]. 8 Press [K \ L] to start scanning.

• The tuner will begin to search up or down automatically. When a channel is found, the unit will stop searching and the picture will appear on the TV screen.

• You can select a desired channel number using [the Number buttons]. Refer to the following Channel Plan table and press the three digits to select the channel number. (To select channel 4, press [0] first and then press [0] and [4]. Or press [4] and then “– – 4” appears and wait for 2 seconds.)

• If desired channel is found, press [0].

Channel Plan

CH Indication TV Channel

1 – 10 IRA - IRJ, GAP 21 – 69 E21 – E69 74 – 78 X, Y, Z, Z+1, Z+2

80 – 99, 100 S1 – S20, GAP

121 – 141 S21 – S41

Introduction Connections

TV View Operation

Basic Setup /

Playback Editing OthersFunction SetupRecording VCR Functions

To cancel auto tuning

Press [SETUP] during scanning.

Note

• The number of TV channels you can get is different depends on your local area.

• If the auto tuning is cancelled during scanning, some channels not yet tuned may not be received.

• Sorting of TV channels from 1 to 6 will be performed automatically as follows. 1: BBC1 2: BBC2 3: ITV 4: CH4 5: CH5 6: SKY NEWS

This unit can receive the Hyper and Oscar frequency bands.

• If you want to decode scrambled signals, select

“Decoder” using [K \ L], then press [1]. Select “ON” using [K \ L], then press [0].

• If “Skip” is set to “ON”, select “Skip” using [K \ L], then press [1]. Select “OFF” using [K \ L], then press [0].

• To store another channel, repeat steps

5 to 8.

9 Press [SETUP] to exit.

E9TK4BD_EN.book Page 22 Wednesday, January 6, 2010 10:05 PM

Skip a Preset Channel

ANALOG

You can set the unit to skip channels. You can no longer receive or watch when you access channels using [PROG. G\H].

1 Follow steps 1 to 4 in “Manual Tuning

(ANALOG)” on page 21.

2 Select “Position” using [K \ L], then press [1]. 3 Select the position number using

[the Number buttons] or [K \ L], then press [0].

4 Select “Skip” using [K \ L], then press [1]. 5 Select “ON” using [K \ L], then press [0].

• To skip another channel, repeat steps 2 to 5.

6 Press [SETUP] to exit.

Move

ANALOG

You can replace two channels.

1 In stop mode, press [SETUP]. Select “General

Setting” using [K \ L], then press [ENTER\OK].

2 Select “Channel” using [K \ L], then press

[ENTER\OK].

3 Select “ANALOG Channel Setup” using [K \ L],

then press [ENTER\OK].

4 Select “Move” using [K \ L], then press

[ENTER\OK].

5 Select the position number to change the

channel using [K \ L], then press [ENTER\OK].

You cannot select a position number where “– – –” appears next to the number, because “Skip” is set to “ON” for that position number.

6 Move the channel to another position number

using [K \ L], then press [ENTER\OK].

• To move another channel, repeat steps 5 to 6.

7 Press [SETUP] to exit.

The tuner scans and memorises all the active DVB channels (TV / Radio) in your area.

Channel Search

S.No. TV Channel

More4

Film4+1

ITV4

CITV

SETANTA SPORT

Channel 69 UHF 858000KHz/8M

Progress

Exit

S.No. Radio Channel

102

Teletext Cars

729

RadioMusicShop

728

Heart

100%

RETURN

Back

5 Press [ENTER\OK] to exit.

• After auto tuning is completed, the lowest memorised DVB channels appears on the screen.

• You can use [PROG. G\H] to change the DVB channels.

Note

• If you press [RETURN/BACK] or [SETUP] during the scanning, auto tuning will be cancelled.

Manual Tuning (DVB)

DVB

You can preset a DVB channel manually and individually.

1 Follow steps 1 to 3 in “Auto Tuning (DVB)” on

page 22.

2 Select “Manual Tuning” using [K \ L], then

press [ENTER\OK].

3 Select your desired position number using

[K \ L], then press [ENTER\OK].

Channel Auto

• The tuner will begin to search up or down automatically. When a DVB channel is found, the unit will stop searching.

• When “Auto” is selected, the unit will search for the channels which have not been stored in channels memory.

4 Press [SETUP] to activate the setting.

Auto Tuning (DVB)

DVB

You can programme the tuner to scan only the DVB channels that you can receive in your area.

1 In stop mode, press [SETUP]. Select “General

Setting” using [K \ L], then press [ENTER\OK].

2 Select “Channel” using [K \ L], then press

[ENTER\OK].

3 Select “DVB Channel Setup” using [K \ L], then

press [ENTER\OK].

4 Select “Auto Tuning” using [K \ L], then press

[ENTER\OK].

The unit will start storing channels available in your area.

$6"#HANNEL3ETUP

%DIT#HANNELS !UTO4UNING

-ANUAL4UNING 3IGNAL)NFORMATION

Service Update

DVB

This unit has “Service Update” function which searches and stores newly available digital channels automatically at 8:00. If a new channel is found, a message will appear on the screen when you turn on the DVB channel at first time after storing a new channel. Press any button to clear the message.

E9TK4BD_EN.book Page 23 Wednesday, January 6, 2010 10:05 PM

TV View Operation

The following operations are available while viewing TV channels through this unit’s tuner.

Select a Channel

DVB ANALOG

To switch DVB, analogue and external input (AV1/AV2/ DV(AV3)) mode. Press [INPUT SELECT F] repeatedly to select DVB, analogue or external input mode. The mode changes as follows:

DVB mode Analogue mode External input mode

You can select external input mode (AV1/AV2/DV(AV3)) by pressing [PROG. G\H] repeatedly. The mode changes as follows:

External input mode (with [PROG. G\H] buttons)

AV1 AV2 DV(AV3)

You can select a channel using [PROG. G\H] or directly enter the channel using [the Number buttons].

Quick Select

DVB

With “Quick Select” menu, you can select your favourite DVB channel quickly. Refer to “Edit Group Lists” on page 24.

1 Press [ENTER\OK] while watching a DVB

channel.

• “Quick Select” menu will appear.

Quick Select

Group: All

S.No. Channel Name

2 Channel4 3 ITV2 4 ITV3

13 Channel4+1

19 More4 28 ITV4 29 E4

View

RETURN

Exit

2 Press [0 \ 1] to select your favourite group list.

(“All”, “Group 1” - “Group 8”)

• “All” shows a list of all the memorised DVB channels.

• If the favourite group does not have any channels, the group will be skipped.

3 Select the DVB channel using [K \ L], then

press [ENTER\OK].

4 Press [RETURN/BACK] to exit.

Introduction Connections

TV View Operation

Basic Setup /

Notes on using [the Number buttons]:

• For one or two-digit number channels, the channels will be identified for 2 seconds after you press the channel number. You can only select channels 1~899 (Digital) or 1~99 (Analogue). If you cannot get a “Station Name” of Analogue channel, it is not indicated with a channel number.

Selecting the Audio Mode

ANALOG

You can switch between TV audio modes by pressing [AUDIO D]. Each mode is indicated on the TV screen.

Audio mode during reception of analogue bilingual broadcasts:

Mode Audio output

Main Main audio from both speakers Main

Sub Sub audio from both speakers Sub

Main / Sub

• Main audio from the left speaker

• Sub audio from the right speaker

• If the programme does not have more than one sound track, [AUDIO D] is not effective.

Display on the

TV screen

Main/Sub

Playback Editing OthersFunction SetupRecording VCR Functions

E9TK4BD_EN.book Page 24 Wednesday, January 6, 2010 10:05 PM

Edit Channels

DVB

With “Edit Channels” menu, you can sort all the memorised DVB channels into the group lists (“Quick Select”) or set the viewer limitation (“Adult Lock”), etc.

1 In stop mode, press [SETUP]. Select “General

Setting” using [K \ L], then press [ENTER\OK].

2 Select “Channel” using [K \ L], then press

[ENTER\OK].

3 Select “DVB Channel Setup” using [K \ L], then

press [ENTER\OK].

4 Select “Edit Channels” using [K \ L], then

press [ENTER\OK].

• “Edit Channels” menu will appear.

Edit Channels

S.No. Channel Name

Five

England Crystal Palac 594000kHz/8M

Re Name Skip Lock Delete

1...8

Move

Add To Fav.

Fav. Skip Lock Del.

RETURN

Exit

Del. Fav.

3 4

1 Channel number 2 Channel name 3 Channel setting

1 to 8: The number of the favourite group list

: Skip Channels : Adult Lock : Delete Channels

4 Channel information 5 Operation Guide

5 Press [RETURN/BACK] to exit.

Edit Group Lists

DVB

You can sort each DVB channel into 8 different favourite group lists (“Group 1” - “Group 8”). With “Quick Select” menu, you can select your favourite DVB channel quickly. Refer to “Quick Select” on page 23.

1 Follow steps 1 to 4 in “Edit Channels” on this

page.

2 Select the DVB channel you want to add to the

favourite group list using [K \ L], then select the number of the favourite group list you want to add using [the Number buttons] ([1] - [8]).

Edit Channels

S.No. Channel Name

Five

England Crystal Palac 594000kHz/8M

Re Name Skip Lock Delete

• The number you selected will appear.

•Press [0] to cancel from the favourite group list.

1...8

Move

Add To Fav.

Fav. Skip Lock Del.

Exit

RETURN

Del. Fav.

3 Press [RETURN/BACK] to exit.

Skip Channels

DVB

You can set the unit to skip the unwanted DVB channels when you use [PROG. G\H].

1 Follow steps 1 to 4 in “Edit Channels” on this

page.

2 Select the DVB channel you want to skip using

[K \ L], then press [GREEN].

Edit Channels

S.No. Channel Name

Five

England Crystal Palac 594000kHz/8M

Re Name Skip Lock Delete

1...8

Move

Add To Fav.

Fav. Skip Lock Del.

RETURN

Exit

Del. Fav.

• “ ” will appear.

•Press [GREEN] to cancel. “ ” will disappear.

3 Press [RETURN/BACK] to exit.

+ 56 hidden pages