Toshiba B-EP800-AC-QM-R Owner's Manual

TOSHIBA AC Adapter

B-EP800-AC-QM-R

Owner's Manual

1

Before using the unit, please read this manual thoroughly and retain it for future
reference.

This symbol is intended to alert the user to the presence of
uninsulated “Dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.

This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.

NOTE:
No user-serviceable parts inside. Refer servicing to qualified service personnel.

Copyright © 2008
by TOSHIBA TEC CORPORATION
All Rights Reserved
570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN

< For EU Only >
TOSHIBA TEC Europe Retail Information Systems S.A.
Rue de la Célidée 33 BE-1080 Brussels

E

PRINTED IN JAPAN
EO1-33082
7FM03290000

2

<English>

<Franaçis>

<Deutsch>

<Español>

<Nederlands>

<Italiano>

<Português>

<Polski>

<한국어>

<中文（繁體字）>

CAUTION!

Do not use this device for any devices other than the B-EP2DL or B-EP4DL series
portable printer.

PRÉCAUTIONS!

N’utilisez pas ce dispositif pour une machine autre que les imprimantes portables
de la gamme B-EP2DL ou B-EP4DL.

Achtung!

Benutzen Sie dieses Netzteil für kein anderes Modell außer dem B-EP2DL oder
dem B-EP4DL.

ATENCIÓN!

No utilice este adaptador para ningún otro dispositivo distinto a las impresoras
portátiles B-EP2DL o B-EP4DL.

WAARSCHUWING!

Gebruik dit toebehoren uitsluitend met draagbare printers van de reeksen B-EP2DL
of B-EP4DL.

ATTENZIONE!

Non utilizzare questo adattatore se non per la serie di stampanti portatili B-EP2DL
o B-EP4DL .

UWAGA!

Nie należy używać tego urządzenia z urządzeniami innymi niż przenośne drukarki
serii B-EP2DL lub B-EP4DL.

주의

!

포터블 프린터 B-EP2DL / B-EP4DL 시리즈 이외에는 사용 하지 말아 주십시오.

注意!
本機只適用与携帯型列印機B-EP2DL / B-EP4DL系列。

ATENÇÃO!

Não utilize este dispositivo para quaisquer outros dispositivos que não a série de
impressoras portáteis B-EP2DL ou B-EP4DL. .

3

CAUTION! (For customers in U.S.A. and Canada)

1.To prevent electric shock, match wide blade of plug to wide slot, fully insert.

2.To reduce the risk of hazards, use only CSA/UL Certified power cord set. Cord is
TypeSPT-2 or heavier, minimum NO.18 AWG copper, one end is provided with a
moulded-on male attachment plug cap (with a specified NEMA configuration),
and the other end is provided with a moulded-on female connector body (with a
specified IEC non-industrial type configuration).

CE Compliance (for EU only)

This product complies with the requirements of EMC and Low Voltage Directives
including their amendments.

NOTES:

1.This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

2.Changes or modification not expressly approved by manufacturer for compliance
could void the user’s authority to operate the equipment.

“This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations. ”
“Cet appareil numérique de la classe B respecte toutes les exigences du
Règlement sur lematériel brouilleur du Canada.” (for CANADA only)

4

NOTICE FOR THE CUSTOMERS IN THE UNITED KINGDOM
A moulded plug complying with BS 1363 is fitted to this equipment for your safety
and convenience.

Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse

approved by ASTA or BSI to BS 1362, (i.e., marked with

or mark) must

be used.

If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the
fuse cover after you change the fuse. Never use the plug without the fuse cover. If you
should lose the fuse cover, please contact your nearest TOSHIBA TEC service
representative.

Others

• The model name plate indicating the operating voltage, power consumption, etc.
is located on the bottom of the unit.

• Unplug the unit from the wall outlet if it will not be used for an extended period of
time. To disconnect the cord (mains lead), pull it out by the plug. Never pull the
cord itself.

• Do not operate the unit with a damaged cord or if it has been dropped or damaged.

• Be sure that nothing metallic comes into contact with the metal parts of the unit or
connecting plate. If it does, a short may occur and the unit may be damaged.

• Always keep the metal contacts clean.

• Do not disassemble or convert the unit.

• Do not apply mechanical shock or drop the unit.

• The unit may become warm whilst in use, this is perfectly normal.

• Keep the unit away from AM receivers, because it will disturb AM reception.

• Do not place the unit in a location where it is:

• Temperatures out of the specification

• Dusty or dirty

• Very humid

• Vibrating
If any difficulty should arise, unplug the unit and contact your Authorised TOSHIBA
TEC representative.

1. To prevent fire or shock hazard, do not expose the unit to rain or moisture.

2. To avoid electrical shock, do not open the cover.

3. Refer servicing to qualified personnel only.

4. For indoor use only.

5

Before using this unit:

Please follow the instructions below to use the B-EP800-AC-QM-R correctly.

• The B-EP800-AC-QM-R is an AC adapter designed for charging the battery pack
loaded in the B-EP2DL/B-EP4DL series portable printers, not for directly supplying
the power to the B-EP2DL/B-EP4DL series portable printers.

This product and the AC adapter supplied with the B-EP800-CHG-QM-R Battery

Charger are the same product.

• DO NOT connect this AC adapter to any devices other than the B-EP2DL/B­EP4DL series portable printer. We assume no responsibility for any results
arising from a connection to other devices.

• Before connecting this AC adapter to the printer, please make sure that the
battery pack is in the printer. We are not responsible for any results due to a
failure to do so.

Connecting the AC Adapter to the Printer

When charging the battery pack loaded in the B-EP2DL/B-EP4DL series portable
printer, use the following procedure to connect the AC adapter to the printer.
For how to check the charge status, please refer to the Owner’s Manual of the B­EP2DL/B-EP4DL series portable printer.

1. Make sure that the battery pack is in the printer.

2. Connect the AC adapter to the DCIN connector of the printer.

3. Connect the power cord to an AC outlet.

4. When the AC adapter is plugged in, the external power source symbol (

) is

displayed on the printer’s LCD, and charging starts. Whether the battery charge
is required or not is automatically determined by the printer.

5. When the charging is completed, unplug the power cord from the AC outlet and

disconnect the AC adapter from the printer.

NOTE:

Charging time may differ
depending on the condition of the
battery pack or the operating
temperature.

AC Adapter

Portable Printer

Plug

DCIN Connector

Power Cord

Power Plug

AC outlet

6

Troubleshooting

If you have any problems while using this product, please check the following point first.
If a problem cannot be solved by taking actions described below, unplug the AC adapter and
contact the dealer or an authorized TOSHIBA TEC service representative for assistance.

Symptom Cause and resolution

The power is not supplied even if the
power cord is connected to an AC
outlet.

(

is not displayed.)

• The AC adapter is not connected to the printer completely.
⇒Firmly connect the AC adapter to the printer.

• The power cord is not connected to the AC adapter completely.
⇒Firmly connect the power cord to the AC

adapter.

• The power cord is not connected to the AC outlet completely.
⇒Firmly connect the power cord to the AC outlet.

• A power failure
⇒Please wait until the power is recovered.

• Power is not supplied to the AC outlet.

⇒Test with other electric appliances. If the power is not

supplied to the AC outlet, please consult the nearest power
company.

• The fuse or breaker of the building has blown out.
⇒ Check the fuse and the breaker.

• The printer is not in stand-by.

⇒The external power source symbol is not displayed while the

printer is not in the stand-by state.

The CHARGE lamp does not light up. • The battery pack is not loaded in the printer.

⇒Load a battery pack in the printer.

• The battery pack loaded in the printer has been fully charged.
⇒A fully charged battery pack is not charged, so

the CHARGE lamp does not light up.

• The ambient temperature or the battery pack temperature does

not fall within the operable temperature range.

⇒Charge the battery pack within 0ºC to 40ºC. A

battery charge may not be started outside this
range.

Specifications

Type: B-EP800-AC-QM-R (Model: 0225A1950)
Input voltage: 100 to 240V AC, 50/60 Hz
Output voltage: DC19V, 2.63A
Application: TOSHIBA Portable Printer B-EP2DL/ B-EP4DL Series
Operating temperature: 0°C to 40°C (32°F to 104°F)
Operating humidity: 20 to 80% (No condensation)
Storage temperature: -20°C to 70°C (-4°F to 158°F)
Storage humidity: 10 to 90% (No condensation)
Dimensions: 98 x 42 x 29.2mm (L/W/H)

(3.86 x 1.65 x 1.15 inches) (Excluding the projecting parts)
Weight: 250g (8.8 oz)
Accessories: Owner’s Manual x 1

NOTE: Design and specifications are subject to change without notice.

7

When purchasing the power cord:

Since the power cord set is not enclosed in this unit, please purchase an approved one that meets the following
standard from your authorized TOSHIBA TEC representative.

(As of August 2008)

Country Agency

Certification

mark

Country Agency Certification mark Country Agency Certification mark

Australia SAA Germany VDE

Sweden SEMKKO

Austria OVE

Ireland NSAI

Switzerland SEV

Belgium CEBEC

Italy IMQ

UK ASTA

Canada CSA

Japan METI

UK BSI

Denmark DEMKO

Netherlands KEMA

U.S.A. UL

Finland FEI

Norway NEMKO

Europe HAR

France UTE

Spain AEE

China CCC

Power Cord Instruction

1. For use with 100 – 125 Vac mains power supply, please select a power cord rated Min. 125V, 10A.

2. For use with 200 – 240 Vac mains power supply, please select a power cord rated Min. 250V.

3. Please select a power cord with the length of 2m or less.

4. The power cord plug connected to the AC adapter must be able to be inserted to an ICE-320-C6 inlet. Refer to
the following figure for the shape.

Country/Region North America Europe

United

Kingdom

Australia China

Power Cord

Rated (Min.)
Type

Conductor size
(Min.)

125V, 10A
SVT

No. 3/18AWG

250V
H05VV-F

3 x 0.75 mm

2

250V
H05VV-F

3 x 0.75 mm

2

250V
AS3191 approved,

Light or Ordinary Duty type

3 x 0.75 mm2

250V
GB5023

3 x 0.75 mm

2

Plug Configuration
(locally approved
type)

Rated (Min.)

125V, 10A

250V, 10A

250V, *1

250V, *1

250V, *1

*1: At least, 125% of the rated current of the product.