Toshiba 72HM196 User Manual

HM196 (E/F) Web 213:276

HIGH-DEFINITION TELEVISION

62HM196 72HM196

YC/N

VX1A00006700

Integrated High Definition DLP

™

Projection Television

Owner’s Record

The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV.

Model number:

Serial number:

For an overview of steps for setting up your new TV, see page 7.

Note: If the TV is powered off and then quickly on again when the lamp unit is hot, it may take several minutes for the picture to appear on-screen. This is a property of DLP

TV lamp technology and is NOT a sign of malfunction. For details, see "IMPORTANT NOTICE ABOUT HOT LAMP RESTART" on page 2.

Note: To display a High Definition picture, the TV must be receiving a High Definition signal (such as an over-the-air High Definition TV broadcast, a High Definition digital cable program, or a High Definition digital satellite program). For details, please contact your TV antenna installer, cable provider, or satellite provider.

IMPORTANT NOTE

Before connecting, operating, or adjusting this product, carefully read the Important Safety, Installation, Care, and Service information in the separate Installation Guide.

HM196_EN.book Page 1 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Important notes about your DLP

™

projection TV

1) The light source for this TV is a projection lamp unit with a limited service life. When the lamp wears out, the picture may become dark or black or the lamp may fail, at which time you must replace the lamp unit (- “Lamp unit replacement and care” on pages 81–83).

2) When the lamp mode is set to Low Power, every time the TV is powered on, the lamp will initially be in High Bright mode but will switch to Low Power mode after a short period of time. You may notice a change in screen brightness when this happens. This is normal and is not a sign of malfunction (- page 55 for details).

3) Every time the TV is powered on, it may take several minutes for the picture to obtain full brightness (- “IMPORTANT NOTICE ABOUT HOT LAMP RESTART,” at right).

4) The TV’s display is manufactured using an extremely high level of precision technology; however, an occasional pixel (dot of light) may show constantly on the screen. This is a structural property of DLP

™

(Digital Light Processing™) technology and is not a sign of malfunction. Such pixels are not visible when the picture is viewed from a normal viewing distance.

5) Always sit approximately 10–25 feet away from the TV and as directly in front of it as possible. The picture quality may be affected by your viewing position and length of viewing time. If you sit too closely to the TV for too long, you may suffer from eye fatigue. See item 29 under “Care” on page 4 of the separate Installation Guide.

6) Depending on the media you are viewing, it is possible, although unlikely, that a limited number of viewers may see a “rainbow effect” on the screen, which can, in rare instances, result in eye fatigue. This is a rare occurrence related to DLP technology and is not a sign of TV malfunction.

7) This TV contains several cooling fans to moderate

the internal temperature. You may be able to hear the fans for several minutes after the TV is turned off. This is a function of the Quick Restart

™

feature and is not a sign of TV malfunction. You can set the Quick Restart

™

feature to stop the fans as soon as the TV

is powered off. See “Setting the Quick Restart

™

feature” (-

page 30).

8) The yellow and blue LED lights at the bottom center of the TV front indicate your TV’s current status. If either light flashes, see “LED indications” (- page 80).

9) Every time the TV power cord is plugged in, the yellow LED will blink until the TV enters standby mode (plugged in but not powered on). This is normal and is not a sign of malfunction.

CAUTION: This television is for use only with the Toshiba stand indicated below. Use with other carts or stands is capable of resulting in instability, causing possible injury.

Television

Stand Model 62HM196 ST 6286 72HM196 ST 7286

“Voice announce” feature

When certain non-standard conditions occur, the LEDs on the TV will blink and the TV will play a recorded “voice announcement” describing the condition (see the LED indication table on page 80 for the specific conditions that include a voice announcement).

To repeat the voice announcement and hear additional information, press the MENU button on the TV while the LEDs are blinking.

IMPORTANT NOTICE ABOUT HOT LAMP RESTART

When the TV has been powered on long enough for the lamp unit to get hot, it may take several minutes for the picture to appear in the following situations:

• When the Quick Restart™ feature is set to OFF and you turn the TV off and then on again within a few minutes; or

• If the TV is on when a short-term power failure, power surge, or other similar power failure occurs, such that the TV loses and regains power within a few minutes.

This is a property of DLP™ technology and is NOT a sign of malfunction.

If this occurs, the yellow LED on the TV front panel will blink (and the blue LED will be lit solid) until the TV is finished restarting the lamp and the normal picture appears. If both LEDs are blinking, you will need to turn the TV off and then on again to restart the lamp.

HM196_EN.book Page 2 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Trademark Information

• This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

• WOW, SRS and l symbol are trademarks of SRS Labs, Inc. WOW technology is incorporated under license from SRS Labs, Inc.

• Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are registered trademarks of Dolby Laboratories.

• CableCARD

™

is a trademark of Cable Television Laboratories, Inc.

• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

• Digital Light Processing

™

, DLP™ and the DLP™ medallion are

trademarks of Texas Instruments.

• In the United States, TV GUIDE and other related marks are registered marks of Gemstar-TV Guide International, Inc. and/or one of its affiliates. In Canada, TV GUIDE is a registered mark of Transcontinental Inc., and is used under license by Gemstar-TV Guide International, Inc. The TV Guide On Screen

™

system is manufactured under license from Gemstar-TV Guide International, Inc. and/or one of its affiliates. The TV Guide On Screen

™

system is protected by one or more of the following United States patents 4,908,713; 6,498,895; 6,850,693; 6,396,546; 5,940,073; 6,239,794 to Gemstar-TV Guide International, Inc. and/or its subsidiaries.

• GEMSTAR-TV GUIDE INTERNATIONAL INC. AND/OR ITS RELATED AFFILIATES ARE NOT IN ANY WAY LIABLE FOR THE ACCURACY OR AVAILABILITY OF THE PROGRAM SCHEDULE INFORMATION OR OTHER DATA IN THE TV GUIDE ON SCREEN SYSTEM AND CANNOT GUARANTEE SERVICE AVAILABILITY IN YOUR AREA. IN NO EVENT SHALL GEMSTAR-TV GUIDE INTERNATIONAL, INC. AND/OR ITS RELATED AFFILIATES BE LIABLE FOR ANY DAMAGES IN CONNECTION WITH THE ACCURACY OR AVAILABILITY OF THE PROGRAM SCHEDULE INFORMATION OR OTHER DATA IN THE TV GUIDE ON SCREEN SYSTEM.

HM196_EN.book Page 3 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Contents

Important notes about your DLP™ projection TV . . . . . . . . . . . 2

Trademark Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Welcome to Toshiba . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Features of your new TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Overview of steps for installing, setting up, and

using your new TV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

TV front and side panel controls and connections . . . . . . . . . 8

TV back panel connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Chapter 2: Using the remote control . . . . . . . . . . . . . . . . . . .11

Installing the remote control batteries . . . . . . . . . . . . . . . . . 11

Remote control effective range . . . . . . . . . . . . . . . . . . . . . . . 11

Learning about the remote control . . . . . . . . . . . . . . . . . . . . 12

Remote Control functional key chart . . . . . . . . . . . . . . . . . . 14

Using the remote control to operate your other devices . . . . 16

Programming the remote control to operate

your other devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Device code setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Searching and sampling the code of a device (8500). . . 17

Using the volume lock feature (8000) . . . . . . . . . . . . . . 17

Operational feature reset (8900). . . . . . . . . . . . . . . . . . . 17

Multi-brand remote control device codes . . . . . . . . . . . . . . . 18

Chapter 3: Menu layout and navigation . . . . . . . . . . . . . . . . .22

Main menu layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Setup/Installation menu layout . . . . . . . . . . . . . . . . . . . . . . . 23

THINC menu layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Navigating the menu system . . . . . . . . . . . . . . . . . . . . . . . . . 24

Chapter 4: Setting up your TV. . . . . . . . . . . . . . . . . . . . . . . . 25

Selecting the menu language . . . . . . . . . . . . . . . . . . . . . . . . 25

Configuring the antenna input sources for the

ANT 1 and ANT 2 terminals . . . . . . . . . . . . . . . . . . . . . 25

Programming channels into the TV’s channel memory . . . . 26

Programming channels automatically . . . . . . . . . . . . . . 26

Manually adding and deleting channels in the channel

memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Setting the time and date. . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Setting the ColorStream

HD audio mode . . . . . . . . . . . . . . 28

Setting the HDMI

™

audio mode . . . . . . . . . . . . . . . . . . . . . . 29

Viewing the CableCARD

™

menu. . . . . . . . . . . . . . . . . . . . . 29

Setting the Quick Restart

™

feature . . . . . . . . . . . . . . . . . . . . 30

Viewing the digital signal meter . . . . . . . . . . . . . . . . . . . . . . 30

Viewing the system status. . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Chapter 5: Using the TV’s features . . . . . . . . . . . . . . . . . . . .32

Selecting the video input source to view . . . . . . . . . . . . . . . 32

Labeling the video input sources . . . . . . . . . . . . . . . . . . . . . 32

Tuning channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Tuning channels using the Channel Browser

™

. . . . . . . 33

Tuning to the next programmed channel . . . . . . . . . . . . 35

Tuning to a specific channel (programmed or

unprogrammed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Switching between two channels

using Channel Return . . . . . . . . . . . . . . . . . . . . . . . 36

Switching between two channels using SurfLock

™

. . . . 36

Selecting the picture size . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Scrolling the TheaterWide

picture

(TheaterWide 2 and 3 only) . . . . . . . . . . . . . . . . . . . . . . 38

Using the auto aspect ratio feature . . . . . . . . . . . . . . . . . . . . 39

Selecting the cinema mode (480i signals only) . . . . . . . . . . 39

Using the POP features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Using the POP double-window feature . . . . . . . . . . . . . 40

Switching the speaker audio (left or right). . . . . . . . . . . 41

POP double-window aspect ratio. . . . . . . . . . . . . . . . . . 41

Using the FREEZE feature . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Adjusting the picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Selecting the picture mode . . . . . . . . . . . . . . . . . . . . . . . 42

Adjusting the picture quality . . . . . . . . . . . . . . . . . . . . . 42

Using the closed caption mode . . . . . . . . . . . . . . . . . . . . . . . 43

Closed Caption Advanced . . . . . . . . . . . . . . . . . . . . . . . 43

Digital closed captions . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Using the Closed Caption button on the

remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Adjusting the audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Muting the sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Using the digital audio selector . . . . . . . . . . . . . . . . . . . 44

Selecting stereo/SAP broadcasts . . . . . . . . . . . . . . . . . . 45

Adjusting the audio quality . . . . . . . . . . . . . . . . . . . . . . 45

Using the StableSound

feature. . . . . . . . . . . . . . . . . . . 46

Turning off the built-in speakers . . . . . . . . . . . . . . . . . . 46

Selecting the optical audio output format . . . . . . . . . . . 46

Using the Locks menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Entering the PIN code . . . . . . . . . . . . . . . . . . . . . . . . . . 47

If you cannot remember your PIN code. . . . . . . . . . . . . 47

Changing your PIN code . . . . . . . . . . . . . . . . . . . . . . . . 47

Blocking TV programs and movies

by rating (V-Chip) . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Downloading an additional rating system

for blocking TV programs and movies . . . . . . . . . . 48

Blocking channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Unlocking programs temporarily . . . . . . . . . . . . . . . . . . 50

Using the input lock feature. . . . . . . . . . . . . . . . . . . . . . 50

Using the GameTimer

™

. . . . . . . . . . . . . . . . . . . . . . . . . 51

Using the control panel lock feature . . . . . . . . . . . . . . . 51

Setting the sleep timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Setting the On/Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Displaying TV status information using RECALL . . . . . . . 53

Understanding the auto power off feature . . . . . . . . . . . . . . 53

Understanding the last mode memory feature . . . . . . . . . . . 53

Chapter 6: Using the TV’s advanced features . . . . . . . . . . . . .54

Using the advanced picture settings features . . . . . . . . . . . . 54

Using dynamic contrast . . . . . . . . . . . . . . . . . . . . . . . . . 54

Using CableClear

digital noise reduction . . . . . . . . . . 54

Using MPEG noise reduction. . . . . . . . . . . . . . . . . . . . . 55

Selecting the color temperature . . . . . . . . . . . . . . . . . . . 55

Selecting the lamp mode . . . . . . . . . . . . . . . . . . . . . . . . 55

Using the Game Mode feature . . . . . . . . . . . . . . . . . . . . 56

Using the advanced audio settings features . . . . . . . . . . . . . 56

Using the SRS WOW

™

surround sound feature . . . . . . 56

HM196_EN.book Page 4 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 7: Using the THINC™ home network feature . . . . . . . .57

A. Connecting the TV to your home network . . . . . . . . . . . 57

B. Setting up the network address . . . . . . . . . . . . . . . . . . . . 57

Automatically setting up the network address . . . . . . . . 57

Manually setting up the network address. . . . . . . . . . . . 58

Resetting the network address . . . . . . . . . . . . . . . . . . . . 59

C. Setting up file sharing on your PC . . . . . . . . . . . . . . . . . . 59

Compatible operating systems . . . . . . . . . . . . . . . . . . . . 59

Setting up file sharing on a PC with Microsoft

Windows

XP Service Pack 1 or Service Pack 2 . . 59

Setting up file sharing on a PC with

Microsoft

Windows® 2000 . . . . . . . . . . . . . . . . . . 60

D. Setting up file sharing on the TV . . . . . . . . . . . . . . . . . . . 61

About the Software Upgrade feature . . . . . . . . . . . . . . . 62

E. Viewing/playing shared files on the TV. . . . . . . . . . . . . . 63

Media specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Using the Picture Viewer . . . . . . . . . . . . . . . . . . . . . . . . 64

Using the Audio Player . . . . . . . . . . . . . . . . . . . . . . . . . 66

F. Setting up e-mail scheduling . . . . . . . . . . . . . . . . . . . . . . 67

Required information and services. . . . . . . . . . . . . . . . . 67

Setting up e-mail scheduling . . . . . . . . . . . . . . . . . . . . . 67

Setting up SMTP authentication . . . . . . . . . . . . . . . . . . 69

Description of fields in the “E-mail Scheduling Setup”

window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

G. Using e-mail scheduling . . . . . . . . . . . . . . . . . . . . . . . . . 73

E-mail parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Sending a request e-mail to the TV . . . . . . . . . . . . . . . . 73

Formatting a request e-mail . . . . . . . . . . . . . . . . . . . . . . 73

Sample request e-mails . . . . . . . . . . . . . . . . . . . . . . . . . 74

Receiving an e-mail from the TV. . . . . . . . . . . . . . . . . . 75

Modifying an existing recording or reminder . . . . . . . . 75

Chapter 8: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .76

General troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Home network troubleshooting . . . . . . . . . . . . . . . . . . . . . . 78

LED indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Chapter 9: Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

Lamp unit replacement and care . . . . . . . . . . . . . . . . . . . . . . 81

Replacing the lamp unit

(User-replaceable component). . . . . . . . . . . . . . . . . 81

When to replace the lamp unit . . . . . . . . . . . . . . . . . . . . 81

How to replace the lamp unit . . . . . . . . . . . . . . . . . . . . . 82

Disposing of the used lamp unit. . . . . . . . . . . . . . . . . . . 83

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Limited United States Warranty

for DLP

™

Television Models . . . . . . . . . . . . . . . . . . . . . 85

Limited Canada Warranty

for DLP

™

Television Models . . . . . . . . . . . . . . . . . . . . . 86

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

HM196_EN.book Page 5 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 1: Introduction

Welcome to Toshiba

Thank you for purchasing this Toshiba TV, one of the most innovative DLP

™

projection TVs on the market.

This digital television is capable of receiving analog basic, digital basic, and digital premium cable television programming by direct connection to a cable system providing such programming. A security card provided by your cable operator is required to view encrypted digital programming. Certain advanced and interactive digital cable services (such as video-on-demand, a cable operator's enhanced program guide, or data-enhanced television services) may require the use of a set-top box. For more information, call your local cable operator.

We have provided three separate Guides to facilitate the installation and operation of your TV.

Please use the Guides in the order shown below to get the most enjoyment from your new TV.

1) The “Installation Guide” explains how to connect your TV to your antenna and equipment.

2) The “Operating Guide” provides step-by-step instructions for using your TV's many features.

3) The “TV Guide On Screen

™

Interactive Program Guide” explains how to set up and navigate the TV Guide On Screen

™

system in your TV.

Note: The TV screen graphics in the Guides are for illustration purposes only and may be different from the screens displayed on your TV.

Features of your new TV

The following are just a few of the many exciting features of your new Toshiba widescreen, integrated HD, DLP

™

projection TV:

• Integrated digital tuning (8VSB ATSC and QAM)

eliminates the need for a separate digital converter set-top box (in most cases).

• TV Guide On Screen

™

no-fee interactive program guide

(- TV Guide On Screen

™

Interactive Program Guide).

• Digital CableCARD

™

slot for viewing encrypted digital

Cable TV programs (- Installation Guide).

• Two HDMI

™

digital, high-definition multimedia interfaces

(- Installation Guide).

• Two sets of ColorStream

HD high-resolution component

video inputs (- Installation Guide).

• Dolby Digital (- Installation Guide) and SRS WOW

™

(- page 56) audio technologies.

• Digital Audio Out optical audio connection with Dolby

Digital optical output format (- page 46; also see Installation Guide).

• CableClear

digital picture noise reduction

(- page 54).

• Double-window POP feature (- page 40).

• Ethernet (RJ-45) (THINC

™

) port for connecting the TV

to a home network to enable file sharing (JPEG, MP3) and e-mail scheduling of recordings and reminders (- Chapter 7 and Installation Guide).

NOTICE OF POSSIBLE TV STAND INSTABILITY

DANGER: RISK OF SERIOUS PERSONAL INJURY OR DEATH! Use this TV only with

the TOSHIBA TV stand listed in the “Specifications” section of this manual. Use with other stands may result in instability, causing possible injury or death.

HM196_EN.book Page 6 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 1: Introduction

Overview of steps for installing, setting up, and using your new TV

Follow these steps to set up your TV and begin using its many exciting features.

1 Carefully read the important safety, installation, care, and

service information in the separate Installation Guide. Keep this manual for future reference.

2 Observe the following when choosing a location for the

TV:

• Read the separate Installation Guide.

• Read the separate TV Guide On Screen

™

Interactive

Program Guide.

• Read “Important notes about your DLP

™

projection

TV” (- page 2).

• Place the TV on the applicable optional TV stand listed

in the “Specifications” section (if available for this TV model) or on a sturdy, level, stable surface that can safely support the size and weight of the unit.

• Place the TV in a location where light does not reflect

on the screen.

• Place the TV far enough from walls and other objects to

allow proper ventilation. Inadequate ventilation may cause overheating, which will damage the TV. THIS TYPE OF DAMAGE IS NOT COVERED UNDER THE TOSHIBA WARRANTY.

3 Do not plug in any power cords until AFTER you have

connected all cables and devices to your TV.

4 BEFORE connecting cables or devices to the TV, learn

the functions of the TV’s connections and controls (

- pages 8–10).

5 Connect your other electronic device(s) to the TV

(

- Installation Guide).

6 Connect the supplied G-LINK

™

/IR blaster cable from

your VCR and/or Cable box (if applicable) to the

G-LINK

™

terminal so you can use the TV Guide

On Screen

™

features (applies to VCRs and cable boxes

only) (- Installation Guide).

7 Install the batteries in the remote control (- page 11). 8 See “Learning about the remote control” (- page 12) for

an overview of the buttons on the remote control.

9 Program the remote control to operate your other

device(s) (

- pages 16–21).

10 AFTER connecting all cables and devices, plug in the

power cords for your TV and other devices.

11 After you plug in the TV power cord, the yellow LED

(on the TV front) will blink 3 times. Wait several seconds until the yellow LED stops blinking and then press p on the TV or remote control.

See “LED indications” (- page 80).

12 See “Menu layout and navigation” for a quick overview of

the TV’s menu system (

- page 22).

13 See the separate TV Guide On Screen

™

Interactive

Program Guide for details on setting up and using the

TV Guide On Screen

™

system (if available in your area).

14 Program channels into the TV’s channel memory

(

- page 26).

15 For details on using the TV’s features, see Chapters 5

and 6.

16 For details on connecting the TV to a home network to

enable file sharing and e-mail scheduling of recordings, see Chapter 7.

17 For help, refer to the Troubleshooting Guide, Chapter 8. 18 For lamp unit replacement instructions, see Chapter 9. 19 For technical specifications and warranty information, see

Chapter 9.

20 Enjoy your new TV!

HM196_EN.book Page 7 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 1: Introduction

TV front and side panel controls and connections

LAMP

POWER

TIMER

REC

Side panel

TV front

Control panel

1 Remote sensor (behind the screen) — Point the remote

control toward this area of the TV screen (- “Remote control effective range” on page 11).

2 Blue, Yellow and Green/Red LEDs

See “LED indications” on page 80 for additional information.

3 POWER — Press to turn the TV on and off.

If the TV stops responding to the controls on the remote control or TV control panel and you cannot turn off the TV, press and hold the POWER button on the TV control panel for 5 or more seconds to reset the TV.

4 CHANNEL U u — When no menu is on-screen, these

buttons change the channel (programmed channels only;

- page 26). When a menu is on-screen, these buttons function as up/down menu navigation buttons.

5 VOLUME + – — When no menu is on-screen, these

buttons adjust the volume level. When a menu is on-screen, these buttons function as left/right menu navigation buttons.

6 INPUT — Repeatedly press to change the source

you are viewing (ANT 1, VIDEO 1, VIDEO 2,

ColorStream HD-1, ColorStream HD-2, HDMI 1, HDMI 2, ANT 2).

7 *MENU (ENTER) — Press to access the menu system

(- pages 22–23). When a menu is on-screen, the MENU button on the TV’s side control panel functions as the ENTER button.

8 ARROWS BbC c — When a menu is on-screen, these

buttons function as up/down/left/right menu navigation buttons.

9 EXIT — Press to instantly close an on-screen menu.

10 GUIDE — Press to access the TV Guide On Screen

™

program guide (- TV Guide On Screen

™

Interactive

Program Guide).

11 VIDEO-2 IN — The side panel A/V connections are

referred to as “VIDEO 2” and include standard A/V inputs plus an optional S-video input.

HM196_EN.book Page 8 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 1: Introduction

TV back panel connections

For an explanation of cable types and connections, see the Installation Guide.

1234 5

1 VIDEO 1 IN — Composite video and analog audio inputs

plus optional S-video inputs for connecting devices with composite video or S-video output.

Note: Composite video and S-video cables carry only video information; separate audio cables are required for a complete connection.

2 ColorStream® HD-1 IN and ColorStream® HD-2 IN

— Two sets of ColorStream

high-definition component video inputs (with analog stereo audio inputs) for connecting devices with component video output, such as a Toshiba DVD player with ColorStream

Note:

• Component video cables carry only video information;

separate audio cables are required for a complete connection.

• HDMI 1 (and 2) share analog audio inputs with

ColorStream HD-1 (and HD-2). To specify the use of the audio inputs for a connected ColorStream (component video) device, see “Setting the ColorStream HD audio mode” on page 28.

3 Variable Audio OUT — Standard analog audio outputs

for connecting an analog amplifier with external speakers.

4 A/V OUT — Standard composite video and analog audio

outputs for connecting a VCR for editing and dubbing.

Note: The A/V OUT terminals will output AUDIO ONLY (no video) in the following instances:

• When the TV's INPUT mode is HDMI, or ColorStream

(- “Selecting the video input source to view,” page 32).

• When the POP window is open (- page 40).

• When the MP3 Audio Player is active (- page 66).

5 IR OUT — For controlling infrared remote-controlled

devices through the TV. You can connect up to two devices with an IR blaster cable, and then control the devices using the TV’s IR pass-through features.

6 ANT 1 and ANT 2 — Two inputs that support analog

(NTSC) and digital (ATSC) off-air antenna signals and analog and digital Cable TV (QAM) signals.

Note: If you have an antenna only, connect it to ANT 1. If you have both cable TV and an antenna, connect the cable TV to ANT 1 and the antenna to ANT 2.

HM196_EN.book Page 9 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 1: Introduction

119 108

7 HDMI™ 1 IN and HDMI™ 2 IN — Two High-Definition

Multimedia Interface inputs receive digital audio and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI device. Also see item 2.

Note: HDMI 1 (and 2) IN share analog audio inputs with ColorStream HD-1 (and HD-2) IN. To specify the use of the audio inputs for a connected HDMI (or DVI) device, see “Setting the HDMI audio mode” on page 29.

8 G-LINK™ — For use with the enclosed IR blaster/

G-LINK

™

cable to enable the TV Guide On Screen™

recording features (- Installation Guide).

9 Digital Audio OUT — Optical audio output in Dolby*

Digital or PCM (pulse-code modulation) format for connecting an external Dolby Digital decoder, amplifier, A/V receiver, or home theater system with optical audio input.

10 RJ-45 (Ethernet) (THINC

™

system**) — Allows you

to connect the TV to your home network. See boxed note below.

11 CableCARD

™

slot — For use with a digital security

card and digital cable TV service (provided by your local cable operator) to view encrypted digital programming (- page 29).

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. CableCARD is a trademark of Cable Television Laboratories, Inc.

* Manufactured under license from Dolby Laboratories.

Dolby, Pro Logic, and the double-D symbol are registered trademarks of Dolby Laboratories.

**THINC™ system

(Toshiba Home Interactive Network Connection)

The RJ-45 (Ethernet) port allows your Toshiba TV to connect to your home network. You can use this revolutionary home entertainment networking system to access MP3 audio files and JPEG picture files that are stored on a networked PC (as shared files) and play/display them on your TV.

You also can play your shared MP3 audio files through a connected audio system.

See Installation Guide and Chapter 7 for details.

HM196_EN.book Page 10 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 2: Using the remote control

Installing the remote control batteries

To install the remote control batteries:

1 Slide the battery cover off the back of the remote control.

2 Install two “AA” size alkaline batteries. Match the + and

– symbols on the batteries to the symbols on the battery compartment.

3 Slide the battery cover on to the remote control until the

lock snaps.

Caution: Never throw batteries into a fire.

Note:

• Be sure to use AA size alkaline batteries.

• Dispose of batteries in a designated disposal area.

• Batteries should always be disposed of with the

environment in mind. Always dispose of batteries in accordance with applicable laws and regulations.

• If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries with new ones.

• When necessary to replace batteries in the remote control, always replace both batteries with new ones. Never mix battery types or use new and used batteries in combination.

• Always remove the batteries from the remote control if they are dead or if the remote control is not to be used for an extended period of time. This will prevent battery acid from leaking into the battery compartment.

Remote control effective range

For optimum performance, aim the remote control directly at the TV remote sensor. Make sure there are no obstructions between the remote control and the TV.

16.4 ft (5m)

Point remote control toward remote sensor on front of TV.

HM196_EN.book Page 11 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 2: Using the remote control

Learning about the remote control

The buttons used for operating the TV only are described here. For a complete list of the remote control’s functions, see the remote control functional key chart (- pages 14–15).

For a list of the buttons that operate the TV Guide On Screen

™

system, see the separate TV Guide On Screen

™

Interactive

Program Guide.

Note: The error message “Not Available” may appear if you press a key for a function that is not available.

1 SLEEP accesses the sleep timer (- page 52).

2 POWER turns the TV on and off. When the TV is on, the

blue LED indicator on the TV front will be illuminated.

Note: The Quick Restart™ setting will affect the amount of time it takes for the picture to appear when you turn on the TV (- page 30).

3 MODE SELECT sets the four remote control device

modes: TV, CABLE/SAT, DVD, and VCR/PVR. Press TV until the keypad blinks 3 times to control the TV. The selected MODE key blinks each time any key is pressed. (

- page 16).

4 Channel Numbers (0–9, –/100) directly tune

channels. The = button is used to tune digital channels (

- page 35) or to edit the Favorite List (- page 33).

5 INPUT selects the video input source (

- page 32).

6 FAV BROWSER accesses the Favorites List in the

Channel Browser

™

(- page 33).

7 MENU accesses the main TV menu system (

- pages 22

and 23) or opens a menu in the TV Guide On Screen

™

system (

- TV Guide On Screen

™

Interactive Program

Guide).

8 ENTER activates highlighted items in the main menu

system and the TV Guide On Screen

™

system.

9 THINC accesses the THINC menu (

- page 24).

10 PAGE + - When the TV Guide On Screen

™

system is open, moves from one set of screen information to the next, when applicable.

11 TV GUIDE opens the TV Guide On Screen

™

system

(

- TV Guide On Screen

™

Interactive Program Guide).

12 3 C / # c While watching TV, these buttons open the

Channel Browser banner and tune to the previous/next channel in the channel history (- page 34). (Also see “Arrow buttons.”)

13 Arrow buttons (BbC c) When a menu is on-screen,

these buttons select or adjust programming menus. (Also see 3 C / # c.)

14 VOL + - adjusts the volume level.

15 CH Bb cycles through programmed channels when no

menu is on-screen (

- page 26), and functions as page up/

down when a menu is on-screen or when the TV Guide On Screen

™

system is open (- TV Guide On Screen™

Interactive Program Guide).

6 8

17 18

23 24

5 7

12 13

16 19

HM196_EN.book Page 12 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 2: Using the remote control

16 EXIT closes on-screen menus and the TV Guide

On Screen

™

system.

17 INFO provides detailed information on highlighted items

in the TV Guide On Screen

™

system (- TV Guide

On Screen

™

Interactive Program Guide).

18 MUTE reduces or turns off the sound (- page 44).

19 CH RTN returns to the last viewed channel (- page 36),

or stops the picture viewer slide show (- page 65). Also can be used to switch between the song select view and file select view in the Audio Player (- page 66).

20 RECALL displays TV status information (- page 53).

21 SKIP Z and z jump backward and forward one day at

a time in the TV Guide On Screen

™

listings (- TV Guide

On Screen

™

Interactive Program Guide).

22 C.CAPTION (TV/VCR) opens the closed caption/audio

selector screen. (For analog channels, the audio selector is not available.) (- pages 43–44.) Also can be used to select the TV mode to view one program while recording another.

23 POP opens the POP double-window (- page 40) or

locks/unlocks the TV Guide On Screen

™

video window

(- TV Guide On Screen

™

Interactive Program Guide).

24 FREEZE freezes the picture. Press again to restore the

moving picture.

25 PIC SIZE cycles through the five pictures sizes: Natural,

TheaterWide 1/2/3, and Full (

- page 37).

HM196_EN.book Page 13 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 2: Using the remote control

Remote Control functional key chart

REMOTE CONTROL KEY

Toshiba TV (TV)

CABLE

SAT (satellite)

VCR

•

DVD/VCR

combo

• DVD/ DVD-R

Receiver/ AMP

CD (AUDIO)

PVR

MODE SELECT

Remote control device mode selection

SLEEP Sleep timer s TV s TV s TV s TV s TV s TV s TV POWER Power Power Power Power Power Power Power Power 1 Digit 1 Digit 1 Digit 1 Digit 1 Digit 1 AV input 1 Digit 1 Digit 1 2 Digit 2 Digit 2 Digit 2 Digit 2 Digit 2 AV input 2 Digit 2 Digit 2 3 Digit 3 Digit 3 Digit 3 Digit 3 Digit 3 AV input 3 Digit 3 Digit 3 4 Digit 4 Digit 4 Digit 4 Digit 4 Digit 4 AV input 4 Digit 4 Digit 4 5 Digit 5 Digit 5 Digit 5 Digit 5 Digit 5 CD Digit 5 Digit 5 6 Digit 6 Digit 6 Digit 6 Digit 6 Digit 6 Tuner Digit 6 Digit 6 7 Digit 7 Digit 7 Digit 7 Digit 7 Digit 7 Phono Digit 7 Digit 7 8 Digit 8 Digit 8 Digit 8 Digit 8 Digit 8 Cassette Digit 8 Digit 8 9 Digit 9 Digit 9 Digit 9 Digit 9 Digit 9 Aux Digit 9 Digit 9 0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 --- Digit 0, 10 Digit 0

100/–/+10

– (digital separator)

---

–/--, +10, +100

+100

–/--, +10, +100

--- --- ---

INPUT

TV/Video select

s TV s TV s TV s TV Input s TV s TV

PIC SIZE

Selects the image shape

s TV s TV s TV s TV s TV s TV s TV

Menu/Guide Menu

Menu Menu --- Menu Menu Menu Menu

FAV BROWSER/ SET UP

FAV BROWSER

--- --- --- Setup --- --- ---

THINC/ TOP MENU

THINC s TV s TV s TV Top menu s TV s TV s TV

TV GUIDE TV Guide Guide Guide --- Guide --- --- Guide INFO Guide Info Info Info --- Display --- --- Info ENTER Enter Select Select --- Select --- --- Select

Menu select up

Cursor up Cursor up --- Cursor up --- --- Cursor up

Menu select down

Cursor down

---

Cursor down

--- ---

Cursor down

C 3 # c

Menu select left/right

3 Back # Next

Cursor left/ right

---

Cursor left/ right

--- ---

Cursor left/right

EXIT/ DVD CLEAR

Exit Exit Exit --- DVD clear --- --- Exit

PAGE +/–

Page up/ down

---

Page up/ down

--- --- ---

VOL +/–

Volume up/ down

Volume up/down

HM196_EN.book Page 14 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 2: Using the remote control

Note:

• “---” = key does not send a signal in that remote control mode.

• “s TV” = key will affect the TV, even though the remote control is in another mode.

• * Not available for your TV.

Volume will affect the TV by default. When the volume is unlocked, all the devices will have their own volume if their ID has volume data. The AUDIO modes (receiver, CD) will have their own volume if volume lock is set on TV, CABLE/SAT, VCR/PVR, or DVD mode. See “Using the volume lock feature” (- page 17).

DVD/DVD-R : RECORD is only for DVD-R, no function is picked for DVD.

DVD/VCR combo : TV/VCR

DVD/VCR combo : DVD/VCR

CH RTN/ DVD RTN

Previous channel

--- DVD RTN --- --- ---

RECALL

On-screen display

s TV s TV s TV s TV s TV s TV s TV

MUTE Sound mute

Sound mute

SLOW

Slow FWD* Slow REW*

--- ---

Slow FWD Slow REW

--- ---

Slow FWD Slow REW

SKIP z SKIP Z

DAY+ DAY–

--- --- ---

Skip FWD Skip REW

---

Skip FWD Skip REW

---

REW Rewind* Rewind Rewind Rewind Rewind --- Rewind Rewind PAUSE/STEP Pause* Pause Pause Pause Pause --- Pause Pause PLAY Play* Play Play Play Play --- Play Play FF Fast FWD* Fast FWD Fast FWD Fast FWD Fast FWD --- Fast FWD Fast FWD C.CAPTION

TV/VCR

C.Caption --- TV/SAT TV/VCR ---

--- --- ---

DISC/AM/FM --- --- --- --- ---

AM/FM

Disc SKIP Disc select

Instant replay

STOP Stop* Stop Stop Stop Stop --- Stop Stop

REC

REC Menu (Single click)

Record (Double click)

--- ---

Record (Double click)

CH B b

Channel up/ down

Channel up/down

---

Channel up/down

POP Split s TV s TV s TV s TV s TV s TV s TV FREEZE Freeze s TV s TV s TV s TV s TV s TV s TV

REMOTE CONTROL KEY

Toshiba TV (TV)

CABLE

SAT (satellite)

VCR

•

DVD/VCR

combo

• DVD/ DVD-R

Receiver/ AMP

CD (AUDIO)

PVR

HM196_EN.book Page 15 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 2: Using the remote control

Using the remote control to operate your other devices

Your TV remote control has one dedicated TV mode and three programmable multi-brand modes: CABLE/SAT, DVD, and VCR/PVR. The default device modes and programmable device modes are listed below.

Note: The TV remote control is preprogrammed to operate most Toshiba devices. To operate a non-Toshiba device or a Toshiba device that the remote control is not preprogrammed to operate, you will need to program the remote control. See “Programming the remote control to operate your other devices” (at right).

Note: Although your new TV’s remote control includes codes for many devices, it may not include codes for some or all of the features on certain devices you wish to control. If you are unable to program the TV’s remote control to operate your device or some of the features on that device, use the device’s remote control or the controls on the device.

Programming the remote control to operate your other devices

Device code setup

Find the code for your device brand in the remote control device code table on pages 18–21.

If more than one code is listed, try each one separately until you find one that works.

2 Press the applicable mode select button (CABLE/SAT,

DVD, or VCR/PVR), until the device button LED blinks

3 times.

3 While holding down E, press the Number buttons to

enter the device category code “0–5” shown below plus the four-digit code for your device.

• If a valid code is entered, the device button LED will

blink twice.

• If an invalid code is entered, the device button LED will

blink one long blink.

4 Point the remote control at the device and press p to test

the code.

• If the device responds to the remote control, you have

entered the correct code.

• If the device does not respond to the remote control,

repeat steps 3 and 4 using another code.

Note: After programming the remote control, make sure all necessary keys on the TV remote control (in addition to p) operate your device. If some keys are not operational, repeat the device code setup using another code (if other codes are listed for your device). If, after trying all listed codes, the necessary keys do not operate your device, use the device’s original remote control.

MODE SELECT

Default device mode control (before programming)

TV Toshiba TV

CABLE/SAT Toshiba DST 3100 Satellite receiver

DVD Orion DVD

VCR/PVR Toshiba VCR

MODE SELECT Device mode control after programming

TV Toshiba TV

CABLE/SAT

Multi-brand video/audio devicesDVD

VCR/PVR

Category Device code

TV (Toshiba) 0

Cable box Satellite receiver Cable/PVR combo DBS/PVR combo (1)

DVD 2

VCR PVR DBS/PVR combo (2)

Audio Amp Audio Amp/Tuners

CD player 5

HM196_EN.book Page 16 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 2: Using the remote control

5 To control the TV, press the “TV” mode select button.

Note:

• Although the TV remote control includes codes for many devices, it may not include codes for some or all of the features on certain devices you want to control. If you are unable to program the TV remote control to operate your device or some of the features on that device, use the device’s original remote control (or the control buttons on the device).

• Every time you change the batteries you will need to reprogram the remote control.

• Some newer VCRs respond to either of two codes. These VCRs have a switch labeled “VCR1/VCR2.” If your VCR has this kind of switch and does not respond to the codes for your VCR brand, set the switch to the other position (“VCR1” or “VCR2”) and reprogram the remote control.

Searching and sampling the code of a device (8500)

If you do not know the device code for a particular device, you can cycle the remote control through the available codes for that device mode and sample the functions to find the code that operates the target device. The keys available to be sampled, provided they are applicable to that mode, are p, 1, z, <, and S. Invalid keys will be ignored while in program mode.

To cycle through each available device code and sample its functions:

1 Press device button to select the mode you want to set up. 2 While holding down E, press 8, 5, 0, 0. The remote

control will enter program mode.

3 Point the remote control at the target device and press p

(or other function buttons that are available to be sampled).

4 If the device responds to the remote control:

Press E to store the device code. The device button LED will blink two times and the remote control will exit the program mode.

If the device does not respond to the remote control:

Press B, and then press p. Repeat this step until the device responds to the remote control, and then press E.

Note: When a search cycle is completed, the device button LED will blink three times. The remote control will begin to cycle through the available codes again. If no key is pressed within 10 seconds during programming, the remote control will exit the program mode and return to the previous code.

Using the volume lock feature (8000)

By default (factory setting), the remote control’s volume keys (z Z and W) are locked to the “TV” device mode.

The remote control will operate the TV’s volume, even when “TV” is not the current device mode.

If you unlock the remote control’s volume keys, each device mode will have its own volume (if the device ID has volume data). The remote control will operate the volume of the device associated with the current device mode.

If you lock the remote control’s volume keys to a specific device mode, the remote control will operate the volume of the device associated with the locked mode, even when the locked mode is not the current device mode.

See “Using the remote control to operate your other devices” on page 16.

To lock the remote control’s volume keys to a specific mode (CABLE/SAT in this example):

1 Press CABLE/SAT. 2 While holding down the E button, press 8, 0, 0, 0. 3 Press z. The CABLE/SAT button LED will blink two

times (locked). The remote control’s volume keys will now operate the

volume of the device associated with the CABLE/SAT mode, even when CABLE/SAT is not the current device mode.

To unlock the remote control’s volume keys:

1 While holding down E, press 8, 0, 0, 0. 2 Press Z. The CABLE/SAT button LED will blink four

times (unlocked).

Operational feature reset (8900)

This feature clears all programmed remote control features not related to “Device code setup” and resets the volume lock to the “TV” device mode.

To reset the remote control:

While holding down E, press 8, 9, 0, 0. The Device button LED will respond with four blinks.

HM196_EN.book Page 17 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 2: Using the remote control

Multi-brand remote control device codes

TVs

Cable boxes

Satellite receivers

DVDs

Brand Code

Toshiba 1524

Brand Code

ABC 0003, 0008 Americast 0899 Bell South 0899 Clearmaster 0883 ClearMax 0883 Coolmax 0883 Digeo 1187 Director 0476 GoldStar 0144 Hamlin 0009, 0273 Memorex 0000 Motorola/ General Instrument/ Jerrold 0276, 0476, 0810 Motorola 1187, 1376 General Instrument/ Jerrold 0003 Multitech 0883 Pace 0008, 0237, 1877 Panasonic 0000, 0107 Paragon 0000 Philips 0317, 1305 Pioneer 0144, 0533, 0877,

1877 Pulsar 0000 Quasar 0000 RadioShack 0883 Regal 0273, 0279 Runco 0000 Samsung 0144 Scientific Atlanta 0008, 0477, 0877,

1877 Sony 1006 Starcom 0003 Supercable 0276 Supermax 0883 Torx 0003 Toshiba 0000 Tristar 0883 V2 0883 Viewmaster 0883 Vision 0883 Vortex View 0883 Zenith 0000, 0525, 0899

Brand Code

AlphaStar 0772 Chaparral 0216 Crossdigital 1109

DirecTV 0099, 0247, 0392,

0566, 0639, 0724, 0749, 0819, 1076, 1108, 1109, 1142, 1377, 1392, 1414, 1442, 1443, 1444, 1609, 1639, 1640, 1749, 1856

Dish Network System 0775, 1005, 1170,

1505, 1775

Dishpro 0775, 1005, 1505,

1775

Echostar 0775, 1005, 1170,

1505, 1775 Expressvu 0775, 1775 GE 0392, 0566 GOI 0775, 1775 Goodmans 1246 Hisense 1535 Hitachi 0819, 1250 HTS 0775, 1775 Hughes 0749, 1442, 1749 Hughes Network Systems 0749, 1142, 1442,

1443, 1444, 1749 iLo 1535 Janeil 0152 JVC 0775, 1170, 1775 LG 1226, 1414 Magnavox 0722, 0724 Memorex 0724 Mitsubishi 0749 Motorola/General Instrument/Jerrold 0869 Motorola 0856 NEC 0102, 0178, 1270 Next Level 0869 Panasonic 0152, 0247, 0701 Paysat 0724 Philips 0099, 0722, 0724,

0749, 0819, 1076,

1142, 1442,

1749 Pioneer 1442 Proscan 0392, 0566 Proton 1535 RadioShack 0869 RCA 0143, 0392, 0566,

0855, 1392 Samsung 1108, 1109, 1142,

1276, 1377, 1442,

1609 Sanyo 1219 Sony 0639, 1639, 1640 Star Choice 0869 Tivo 1142, 1442, 1443,

1444 Toshiba 0082, 0749, 0790,

0819, 1285, 1286,

1287, 1289, 1749,

1857, 1858 UltimateTV 1392, 1640 Uniden 0722, 0724 US Digital 1535 USDTV 1535 Voom 0869 Zenith 1856

Brand Code

Aiwa 0641 Akai 0695, 0770, 1089 Alco 0790 Allegro 0869 Amphion Media Works 0872 AMW 0872 Apex Digital 0672, 0717, 0755,

0794, 0796, 0797, 1004, 1020,

1056, 1061, 1100 Aspire Digital 1168, 1407 Audiovox 0790, 1041, 1072 Axion 1072 B & K 0655, 0662 Blaupunkt 0717 Blue Parade 0571 Broksonic 0695 California Audio Labs 0490 Cinea 0831 CineVision 0833, 0869, 0876 Citizen 1277 Coby 0778, 0852, 1086,

1107, 1177, 1351 Craig 0831 Curtis Mathes 1087 CyberHome 0816, 0874, 1023,

1024, 1117, 1129 Daewoo 0705, 0784, 0833,

0869, 1169, 1172,

1234, 1242 Daytek 0872 Denon 0490, 0634 Desay 1407 Disney 0675, 1270 Dual 1068, 1085 Durabrand 1127 DVD2000 0521 Emerson 0591, 0675, 0821 Enterprise 0591 Fisher 0670 Funai 0675, 1334 Gateway 1073, 1077, 1158 GE 0522, 0717, 0815 Go Video 0715, 0741, 0744,

0783, 0833, 0869,

1044, 1075,

1099, 1158, 1304,

1730 GoVision 1072 GoldStar 0741 GPX 0699, 0769 Gradiente 0490 Greenhill 0717 Grundig 0539 Harman/Kardon 0582, 0702 Hitachi 0573, 0664 Hiteker 0672 iLo 1348 Initial 0717 Integra 0571, 0627 Jaton 1078

HM196_EN.book Page 18 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 2: Using the remote control

VCRs

JBL 0702 JSI 1423 JVC 0558, 0623, 0867,

1164 jWin 1049, 1051 Kawasaki 0790 Kenwood 0490, 0534 KLH 0717, 0790, 1020,

1149 Konka 0711 Koss 0651, 1423 Landel 0826 Lasonic 0798, 1173 Lecson 1533 Lenoxx 1127 LG 0591, 0741, 0801,

0869 LiteOn 1058, 1158, 1416,

1440 Loewe 0511 Magnavox 0503, 0539, 0646,

0675, 0821 Malata 0782, 1159 Marantz 0539 McIntosh 1533 Memorex 0695, 0831, 1270 Microsoft 0522 Mintek 0717, 0839 Mitsubishi 0521, 1521 Momitsu 1082 NAD 0591, 0692, 0741 NEC 0785 Nesa 0717 Next Base 0826 NexxTech 1402 Norcent 0872, 1003, 1107,

1265 Onkyo 0503, 0627, 0792 Oritron 0651 Panasonic 0490, 0503, 0703,

1362, 1462, 1490,

1762 Philips 0503, 0539, 0646,

0675, 1267, 1354 PianoDisc 1024 Pioneer 0525, 0571, 0631 Polaroid 1020, 1061, 1086 Polk Audio 0539 Portland 0770 Presidian 0675 Proceed 0672 Proscan 0522 ProVision 0778 Qwestar 0651 RCA 0522, 0571, 0717,

0790, 0822 Rio 0869 RJTech 1360 Rotel 0623 Rowa 0823 Sampo 0698, 0752 Samsung 0490, 0573, 0744,

0820, 1044, 1075 Sansui 0695 Sanyo 0670, 0695, 0873 Sensory Science 1158

Sharp 0630, 0675, 0752,

1256 Sharper Image 1117 Sherwood 0633, 0770, 1043,

1077 Shinsonic 0533, 0839 Sonic Blue 0869, 1099 Sony 0533, 0864, 1033,

1431, 1533 Sungale 1074 Superscan 0821 SVA 0860, 1105 Sylvania 0675, 0821 Symphonic 0675 Teac 0790, 0809 Technics 0490, 0703 Technosonic 0730 Techwood 0692 Theta Digita 0571 Toshiba 0503, 0695, 1154,

1854 Tredex 0800, 0803, 0804 Urban Concepts 0503 US Logic 0839 Venturer 0790 Vizio 1064, 1226 Xbox 0522 Yamaha 0490, 0539, 0545 Yamakawa 0872 Zenith 0503, 0591, 0741,

0869 Zoece 1265

Brand Code

ABS 1972 Admiral 0048, 0209, 0479 Adventura 0000 Aiko 0278 Aiwa 0000, 0037, 0124 Akai 0041, 0061, 0175 Alienware 1972 America Action 0278 American High 0035 Asha 0240 Audiovox 0037, 0278 Beaumark 0240 Bell & Howell 0104 Broksonic 0002, 0121, 0184,

0209, 0479 Calix 0037 Canon 0035 Carver 0081 CCE 0072, 0278 Citizen 0037, 0278 Colt 0072 Craig 0037, 0047, 0072,

0240 Curtis Mathes 0035, 0041, 0060,

0162 Cybernex 0240 CyberPower 1972 Daewoo 0045, 0278 Dell 1972 Denon 0042

DirecTV 0739 Durabrand 0038, 0039 Dynatech 0000 Electrohome 0037, 0043 Electrophonic 0037 Emerex 0032 Emerson 0000, 0002, 0037,

0043, 0061, 0121, 0184, 0209, 0212, 0278, 0479,

0593, 1593 Fisher 0047, 0104 Fuji 0033, 0035 Funai 0000, 0593, 1593 Garrard 0000 Gateway 1972 GE 0035, 0060, 0065,

0240, 0807 Go Video 0240, 0432, 0526 GoldStar 0037, 0038 Gradiente 0000 Harley Davidson 0000 Harman/Kardon 0038, 0075, 0081 Harwood 0072 Headquarter 0046 Hewlett Packard 1972 HI-Q 0047 Hitachi 0000, 0041, 0042,

0065, 0089, 0105 Howard Computers 1972 HP 1972 Hughes Network Systems

0042, 0739

Humax 0739 Hush 1972 iBUYPOWER 1972 Jensen 0041 JVC 0008, 0041, 0067 KEC 0037, 0278 Kenwood 0038, 0041, 0067 KLH 0072 Kodak 0035, 0037 Linksys 1972 Lloyd's 0000 Logik 0072 LXI 0037 Magnasonic 0593 Magnavox 0000, 0035, 0039,

0081, 0149, 0563,

0593 Magnin 0240 Marantz 0035, 0081 Marta 0037 Matsushita 0035, 0162 Media Center PC 1972 MEI 0035 Memorex 0000, 0035, 0037,

0039, 0046, 0047,

0048, 0104,

0162, 0209, 0240,

0479 MGA 0043, 0061, 0240 MGN Technology 0240 Microsoft 1972 Mind 1972 Minolta 0042, 0105

(continued)

HM196_EN.book Page 19 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 2: Using the remote control

PVRs

Cable/PVR Combo

DBS/PVR Combo (1)

DBS/PVR Combo (2)

Mitsubishi 0043, 0061, 0067,

0075, 0173, 0807 Motorola 0035, 0048 MTC 0000, 0240 Multitech 0000, 0072 NEC 0038, 0040, 0041,

0067, 0104 Nikko 0037 Nikon 0034 Niveus Media 1972 Noblex 0240 Northgate 1972 Olympus 0035, 0226 Onkyo 0222 Optimus 0037, 0048, 0104,

0162, 0432, 0593,

1062 Orion 0002, 0184, 0209,

0479 Panasonic 0035, 0077, 0162,

0225, 0226, 0616,

1062 Penney 0035, 0037, 0038,

0040, 0042, 0240 Pentax 0042, 0065, 0105 Philco 0035 Philips 0035, 0081, 0618,

0739, 1081, 1181 Pilot 0037 Pioneer 0067 Polk Audio 0081 Profitronic 0240 Proscan 0060 Protec 0072 Pulsar 0039 Quarter 0046 Quartz 0046 Quasar 0035, 0077, 0162 RadioShack 0000 Radix 0037 Randex 0037 RCA 0042, 0060, 0065,

0077, 0105, 0149,

0240, 0807,

0880 Realistic 0000, 0035, 0037,

0046, 0047, 0048,

0104 ReplayTV 0614, 0616 Ricavision 1972 Ricoh 0034 Runco 0039 Salora 0075 Samsung 0045, 0240, 0739 Sanky 0039, 0048 Sansui 0000, 0041, 0067,

0209, 0479 Sanyo 0046, 0047, 0104,

0159, 0240 Scott 0043, 0045, 0121,

0184, 0210, 0212 Sears 0000, 0035, 0037,

0042, 0046, 0047,

0104, 0105 Sharp 0048, 0807, 0848 Shintom 0072 Shogun 0240

Singer 0072 Sonic Blue 0614, 0616 Sony 0000, 0032, 0033,

0034, 0035, 0636,

1032, 1972 Stack 9 1972 STS 0042 Sylvania 0000, 0035, 0043,

0081, 0593, 1593 Symphonic 0000, 0593, 1593 Systemax 1972 Tagar Systems 1972 Tatung 0041 Teac 0000, 0041 Technics 0035, 0162 Teknika 0000, 0035, 0037 Thomas 0000 Tivo 0618, 0636, 0739,

1996 TMK 0240 Toshiba 0043, 0045, 0209,

0210, 0212, 0366,

0845, 1008,

1145, 1972, 1996 Totevision 0037, 0240 Touch 1972 Unitech 0240 Vector 0045 Vector Research 0038, 0040 Video Concepts 0040, 0045, 0061 Videomagic 0037 Videosonic 0240 Viewsonic 1972 Villain 0000 Voodoo 1972 Wards 0000, 0035, 0042,

0047, 0048, 0060,

0072, 0081,

0149, 0212, 0240 White Westinghouse 0072, 0209 XR-1000 0000, 0035, 0072 Yamaha 0038 Zenith 0000, 0033, 0034,

0039, 0209, 0479,

1139 ZT Group 1972

Brand Code

ABS 1972 Alienware 1972 CyberPower 1972 Dell 1972 Direc TV 0739 Gateway 1972 Hewlett Packard 1972 Howard Computers 1972 HP 1972 Hughes Network Systems 0739 Humax 0739 Hush 1972 iBUYPOWER 1972 Linksys 1972 Media Center PC 1972

Microsoft 1972 Mind 1972 Niveus Media 1972 Northgate 1972 Panasonic 0616 Philips 0618, 0739 RCA 0880 ReplayTV 0614, 0616 Sonic Blue 0614, 0616 Sony 0636, 1972 Stack 9 1972 Systemax 1972 Tagar Systems 1972 Tivo 0618, 0636, 0739 Toshiba 1008, 1972 Touch 1972 Viewsonic 1972 Voodoo 1972 ZT Group 1972

Brand Code

Americast 0899 Digeo 1187 Motorola/ General Instrument/ Jerrold 0476, 0810 Motorola 1187, 1376 Pace 0237, 1877 Pioneer 0877, 1877 Scientific Atlanta 0877, 1877 Sony 1006 Supercable 0276 Zenith 0899

Brand Code

DirecTV 0099, 0392, 0639,

1076, 1142, 1377, 1392, 1442,

1443, 1444, 1640 Dish Network System 0775, 1505 Dishpro 0775, 1505 Echostar 0775, 1170, 1505 Expressvu 0775 Hughes Network Systems 1142, 1442, 1443,

1444 JVC 1170 Motorola 0869 Philips 1142, 1442 Proscan 0392 RCA 1392 Samsung 1442 Sony 0639, 1640 Star Choice 0869

Brand Code

Hughes Network Systems 0739 Philips 0739 Samsung 0739

HM196_EN.book Page 20 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 2: Using the remote control

Audio Amp

CD players

Audio Amp/Tuners

Brand Code

Adcom 0577, 1100 Bose 0674 Carver 0892 Durabrand 1561 Elan 0647 GE 0078 Harman/Kardon 0892 JVC 0331 LeftCoast 0892 Lenoxx 1561 Luxman 0165 Marantz 0321, 0892 McIntosh 0251 Nakamichi 0321 NEC 0264 Optimus 0395, 0823 Parasound 0246 Philips 0892 Pioneer 0823 PolkAudio 0892 RCA 0823 Realistic 0395 Sansui 0321 Shure 0264 Sony 0689, 0815, 1126 Soundesign 0078, 0211 Victor 0331 Wards 0078, 0211 Yamaha 0133, 0143, 0354,

0504

Brand Code

Adcom 0234 Aiwa 0124, 0157 Akai 0156 Arcam 0157 Audio-Technica 0170 Burmester 0420 California Audio Labs 0029, 0303 Carver 0157, 0299 Denon 0003, 0034 DKK 0000 DMX Electronics 0157 Garrard 0393, 0420 Genexxa 0032 Harman/Kardon 0083, 0157, 0173 Hitachi 0032, 0139 Integra 0101 JVC 0072, 0655, 1294 Kenwood 0028, 0037, 0190,

0626 Krell 0157 Linn 0157 Magnavox 0038, 0157 Marantz 0029, 0038, 0157,

0180, 0435, 0626 MCS 0029 MGA 0083 Miro 0000 Mission 0157 Mitsubishi 0083

MTC 0420 NAD 0019, 0299 NEC 0234 Nikko 0170 NSM 0157 Onkyo 0101, 0102, 0138,

0381, 1327

Optimus 0000, 0032, 0037,

0087, 0420, 0468

Panasonic 0029, 0303, 0388,

0752 Parasound 0420 Philips 0157, 0274, 0626 Pioneer 0032, 0468, 0551,

1062, 1087 Polk Audio 0157 Proceed 0420 Proton 0157 QED 0157 Quad 0157 Quasar 0029 RCA 0032, 0053, 0420,

0468, 1062 Realistic 0180, 0420 Rotel 0157, 0420 SAE 0157 Sansui 0157 Sanyo 0087 Sharp 0037, 0180 Sherwood 0180 Sonic Frontiers 0157 Sony 0000, 0100, 0185,

0490, 0604, 0605,

0673, 1364 Sugden 0157 TAG McLaren 0157 Tascam 0420 Teac 0180, 0378, 0393,

0420 Technics 0029, 0303 Toshiba 0019, 0299 Victor 0072 Wards 0053, 0157 Yamaha 0036, 0170, 0187,

0490, 1292

Brand Code

ADC 0531 Aiwa 0121, 0189, 1243,

1388, 1405, 1641 Akai 1255, 1512 Alco 1390 AMC 1077 Anam 1074, 1609 Apex Digital 1774 Arcam 1189 Audiotronic 1189 Audiovox 1390 Bose 0639, 1229, 1253,

1933 Capetronic 0531 Carver 0121, 0189, 1189,

1289 Delphi 1414 Denon 0121, 1142, 1360

Fisher 1801 Harman/Kardon 0110, 0189, 0891,

1289, 1304, 1306 Hitachi 1273, 1801 Integra 0135, 1298, 1320 JBL 0110, 1306 JVC 1058, 1374, 1495,

1811 Kenwood 0186, 1313, 1569,

1570 KLH 1390, 1428 Linn 0189 Magnavox 0189, 0531, 1189,

1269, 1514 Marantz 0189, 1189, 1269,

1289 McIntosh 1289 Micromega 1189 Mitsubishi 1393 Myryad 1189 Nakamichi 1313 Onkyo 0135, 0380, 0842,

1298, 1320, 1531 Optimus 0186, 0531, 1023,

1074 Panasonic 0309, 1288, 1308,

1316, 1350, 1363,

1518, 1548,

1633, 1763, 1764 Philips 0189, 1189, 1266,

1269 Pioneer 0014, 0150, 0531,

0630, 1023, 1384 Polk Audio 0189, 1289, 1414 Proscan 1254 RCA 0531, 1023, 1074,

1254, 1390, 1511,

1609 Samsung 1295, 1304, 1500 Sansui 0189, 1189 Sanyo 1469, 1801 Sharp 0186 Sherwood 1077 Sirius 1811 Sony 0168, 1058, 1258,

1406, 1441, 1558,

1622, 1658,

1758, 1759, 1858 Stereophonics 1023 Sunfire 1313 Teac 1074, 1267, 1390,

1528 Technics 0309, 1308, 1518,

1633 Thorens 1189 Toshiba 0135 Venturer 1390 Wards 0014, 0189 XM 1406, 1414 Yamaha 0176, 0186, 1176,

1276, 1331, 1375

HM196_EN.book Page 21 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 3: Menu layout and navigation

Main menu layout

The tables below and on the next page provide a quick overview of your TV’s menu system. To open the main menus (illustrated below), press Y on the remote control or TV control panel.

Icon Item Option

Picture Viewer S [Launches the JPEG Picture Viewer] Audio Player S [Launches the MP3 Audio Player] Channel Browser

™

S [Launches the Channel Browser™]

TV Guide On Screen

™

S [Opens the TV Guide On Screen™ option]

Digital CC/Audio Selector

S [Launches the ATSC Digital CC Selector] (This option is not available

if you are not on a digital channel).

CableCARD

™

S Dynamic list of items provided by Cable company.

(This option is not available if a CableCARD

™

is not inserted.)

Picture Settings S [Opens the Picture Settings menu] Advanced Picture Settings S [Opens the Advanced Picture Settings menu]

Theater Settings S [Opens the Theater Settings menu]

Audio Settings S [Opens the Audio Settings menu] Advanced Audio Settings S [Opens the advanced Audio Settings menu]

Audio Setup S [Opens the Audio Setup menu]

Closed Caption Mode S OFF/CC1/CC2/CC3/CC4/T1/T2/T3/T4 Closed Caption Advanced S [Opens the Closed Caption Advanced menu] Input Labeling S [Opens the Input Labeling menu] Menu Language S English/French/Spanish Channel Browser Setup S [Opens the Channel Browser Setup menu] Enable Rating Blocking S Off/On Edit Rating Limits S [Opens the Edit Rating Limits menu] Channels Block S [Opens the Channels block menu] Input Lock S Off/Video/Video+ Front Panel Lock S Off/On GameTimer

™

S Off/30 Min/60 Min/90 Min/120 Min New PIN Code S [Opens the New PIN Code entry screen] Installation S [Opens the Installation menu (- page 23)] Sleep Timer S [Opens the Sleep Timer menu] On/Off Timer S [Opens the On/Off Timer menu] ColorStream HD1 Audio S No/Yes HDMI 1 Audio S Auto / Digital / Analog ColorStream HD2 Audio S No/Yes HDMI 2 Audio S Auto / Digital / Analog Slide Show Interval S 2 Sec/5 Sec/10 Sec/15 Sec/20 Sec Quick Restart

™

S Off/On

Applications

Video

Audio

Preferences

Locks

Setup

HM196_EN.book Page 22 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 3: Menu layout and navigation

Setup/Installation menu layout

The Installation menu contains the Terrestrial, Network, TV Guide On Screen™ Setup, Time and Date, and System Status menus. To open the Installation menu (illustrated below), press Y on the remote control or TV control panel, open the Setup menu,

select Installation, and press T.

Icon Item Option

Press Y, open the Setup menu, and then open the Installation sub-menu.

Input Configuration S [Opens the Input Configuration menu]

Channel Program

S ANT1 S [Scans for new channels on ANT1] S ANT2 S [Scans for new channels on ANT2]

Channel Add/Delete S [Opens the Channel Add/Delete menu] Signal Meter S [Opens the Signal Meter menu] Basic Network Setup S [Opens the Basic Network Setup menu] E-mail Scheduling Setup S [Opens the E-mail Scheduling Setup menu] Home File Server Setup S [Opens the Home File Server Setup menu] Software Upgrade S [Opens the Software Upgrade menu]

Start

S [Opens the TV Guide On Screen

™

Setup

menu]

Start Setup S [Opens the Time and Date Setup menu]

System Information S [Opens the System Information screen]

Terrestrial

Network

TV Guide On Screen™ Setup

Time and Date

System Status

HM196_EN.book Page 23 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 3: Menu layout and navigation

THINC menu layout

The THINC menu will not be part of the main menu, but will be viewable by pressing C on the remote control. It will contain a list of special features offered by the TV; Picture

Viewer, Audio Player, Channel Browser, Favorites Browser, and TV Guide On Screen.

Navigating the menu system

You can use the buttons on the remote control or TV control panel to access and navigate your TV’s on-screen menu system.

• Press Y to open the menu system.

• When a menu is open, use the up/down/left/right arrow

buttons (BbC c) on the remote control or TV control panel to move in the corresponding direction in the menu.

• Press T to save your menu settings or select a highlighted

item. (A highlighted menu item appears in a different color in the menu.)

• All menus close automatically if you do not make a selection

within 60 seconds, except the signal meter menu, which closes automatically after about 5 minutes.

• To close a menu instantly, press O.

Note: The menu backgrounds may sometimes appear black, depending on the signal the TV is receiving. This is not a sign of malfunction.

THINC Applications

Picture Viewer

Audio Player

Channel Browser

Favorites Browser

TV Guide On Screen

CH RTNENTER

EXIT

Navigate

Select

Back Exit

Applications

Audio Player

Channel Browser

Picture Viewer

Digital CC/Audio Selector

CableCARD

TV Guide On Screen

HM196_EN.book Page 24 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 4: Setting up your TV

Selecting the menu language

You can choose from three different languages (English, French, and Spanish) for the on-screen display of menus and messages.

Note: The TV Guide On Screen™ menus are in English, regardless of the language selected in this menu.

To select the menu language:

1 Press Y and open the Preferences menu. 2 Highlight Menu Language and press c. 3 Press B or b to select your preferred menu language and

press T.

4 Press O to close the Preferences menu.

Configuring the antenna input sources for the ANT 1 and ANT 2 terminals

To configure the ANT 1 and ANT 2 input sources:

1 Press Y and open the Setup menu. 2 Highlight Installation and press T.

3 (A new set of Installation menu icons will appear, as

shown below.) Open the Terrestrial menu, highlight Input Configuration, and press T.

Note: The Terrestrial menu may not be accessible (items will be “grayed out”) in some instances (for example, if a cable box is connected to the ANT 1 input or if one of the VIDEO modes is the current input during TV Guide On Screen

™

setup).

4 Press B or b to highlight Antenna 1 In, and press C or

c to select the input source (Cable or Antenna) for the

ANT 1 input on the TV.

Note: If a cable box is connected to the ANT 1 input during TV Guide On Screen

™

setup, the entire Terrestrial menu will not be accessible, including the input source for ANT 1, which will automatically display “Cable Box.”

5 Press b to highlight Antenna 2 In and then C or c to

select the input source (Cable or Antenna) for the ANT 2 input on the TV, if applicable. If you have not connected anything to the ANT 2 input, skip this step.

6 To save your new settings, highlight Done and press T.

To revert to your original settings, highlight Cancel and press T.

CH RTNENTER

EXIT

Navigate

Select

Back Exit

Channel Browser Setup

English

Français

Español

Closed Caption Mode

Off

Closed Caption Advanced

Input Labeling

Menu Language English

Preferences

CH RTNENTER

EXIT

Navigate

Select

Back Exit

Installation

Sleep Timer

On/Off Timer

Setup

Auto

ColorStream HD1 Audio

HDMI 1 Audio

ColorStream HD2 Audio

Auto

HDMI 2 Audio

CH RTNENTER

EXIT

Navigate

Select

Back Exit

Terrestrial

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

Input Configuration

Antenna 1 In

Antenna 2 In

Cable

Antenna

Cancel Done

HM196_EN.book Page 25 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 4: Setting up your TV

Programming channels into the TV’s channel memory

When you press < or , on the remote control or TV control panel, your TV will stop only on the channels you programmed into the TV’s channel memory.

Follow the steps below to program channels into the TV’s channel memory.

Programming channels automatically

Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are programmed automatically, you can manually add or erase individual channels in the channel memory.

Note:

• You must configure the antenna input source before

programming channels (- page 25).

• If the Antenna 1 input signal type is set to Cable, the automatic channel programming process erases channels that were previously programmed into the TV’s memory.

• If the Antenna 1 input signal type is set to Antenna, the automatic channel programming process adds newly found channels to the existing set of programmed channels (and does NOT erase channels that were previously programmed into the TV’s memory). To remove an antenna source channel from the memory, you must manually delete it.

• To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control.

• Programming channels when the antenna input is configured for Cable will take substantially longer than when the antenna input is configured for Antenna. This is normal; however, once channel programming is finished, you should not have to repeat the programming process again unless your Cable TV service lineup changes significantly.

• If you have a CableCARD

™

inserted, channel programming

for the ANT 1 input is disabled because the CableCARD

™

automatically loads the Cable channel list into the TV’s channel memory. See the Installation Guide for details on CableCARD

™

To program channels automatically:

1 Configure the antenna input sources, if you have not

already done so. (

- page 25).

2 Press Y and open the Setup menu. 3 Highlight Installation and press T.

4 (A new set of Installation menu icons will appear, as

shown below.) Open the Terrestrial menu, highlight Channel Program, and press T.

5 Highlight ANT 1 or ANT 2, depending on which antenna

input you want to program channels for, and then press T to start automatic channel programming.

The TV will automatically cycle through all the antenna channels, and store all active channels in the channel memory. While the TV is cycling through the channels, the message “Scanning channels, please wait” appears (as shown above).

6 To cancel channel programming, either press O or

highlight Abort in the on-screen display and press T. When channel programming is finished, press < or , to

view the programmed channels.

CH RTNENTER

EXIT

Navigate

Select

Back Exit

Installation

Sleep Timer

On/Off Timer

Setup

Auto

ColorStream HD1 Audio

HDMI 1 Audio

ColorStream HD2 Audio

Auto

HDMI 2 Audio

CH RTNENTER

EXIT

Navigate

Select

Back Exit

Terrestrial

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

ANT 1 Antenna Scanning channels, please wait ...

Abort

52%

HM196_EN.book Page 26 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 4: Setting up your TV

Manually adding and deleting channels in the channel memory

After automatically programming channels into the channel memory, you can manually add or delete individual channels.

To add or delete channels in the channel memory:

1 Press Y and open the Setup menu. 2 Highlight Installation and press T. 3 (A new set of Installation menu icons will appear, as

shown below.) Open the Terrestrial menu, highlight Channel Add/Delete, and then press T.

4 The illustration below left shows channels programmed

for the ANT 1 antenna input. To view the list of channels programmed for the ANT 2 or Cable box antenna input, press Bb to highlight ANT 2 and press T.

To add a channel to the channel memory:

Highlight the unchecked box next to the channel number you want to add, and then press T to check the box.

To manually add digital subchannels on a physical channel:

Use the Channel Numbers and the Dash (=) on the remote control to enter the channel number (for example, 56–1).

If the channel is found, the number will be added to the list and the box will be checked.

If the channel is not found, a message will appear.

To remove a channel from the channel memory:

Highlight the checked box next to the channel number you want to remove, and then press T to uncheck the box.

To save your new settings:

Highlight Done and press T.

To revert to your original settings:

Highlight Cancel and press T before saving.

To remove all channels from the channel memory:

Highlight Reset and press T, and then highlight Done and press T.

Note: This action applies to the current antenna input only. To delete/add channels on the other input, highlight the input you want (ANT1, or ANT 2) and press T.

CH RTNENTER

EXIT

Navigate

Select

Back Exit

Terrestrial

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

Channel Add/Delete

Analog ANT 1

ANT 2

Reset

Cancel

Done

Digital

Analog

Digital

Analog

2 - 1

2 - 2

7 - 1

Channel Add/Delete

Analog ANT 1

ANT 2

Analog

Reset

Cancel

Done

Channel Add/Delete

Analog ANT 1

ANT 2

Reset

Cancel

Done

Digital

Analog

Digital

Analog

Digital

Analog

2 - 1

2 - 2

7 - 1

HM196_EN.book Page 27 Tuesday, May 30, 2006 2:18 PM

HM196 (E/F) Web 213:276

Chapter 4: Setting up your TV

Setting the time and date

Note: If you already set up the TV Guide On Screen™ system, the time and date were set automatically and you can skip this step.

To set the time and date:

1 Press Y and open the Setup menu. 2 Highlight Installation and press T. 3 (A new set of Installation menu icons will appear, as

shown below.) Open the Time And Date menu, highlight Start Setup, and press T.

If you have not set up the TV Guide On Screen

™

system,

the following screen will appear. To set the time, highlight

TV Guide On Screen

™

and press T. The TV Guide

On Screen

™

setup sequence will start, and the time and

date will be set automatically.

If you have already set up the TV Guide On Screen

™

system, or if you have not set up the time, the Time and Date setting screen will appear and you will need to manually set the time and date.

Note:

• If you highlight TV Guide On Screen

™

(above) to set the

time and date through the TV Guide On Screen

™

system and a power outage occurs, the time and date will be updated automatically when the power is restored.

• If you highlight Manual (above) to set the time and date manually and a power outage occurs, you will lose the time and date settings when the power is restored.

• If you manually set the time and date and then perform TV Guide On Screen

™

setup, the manual time and date

settings will be overridden by the TV Guide On Screen

™

settings.

Setting the ColorStream® HD audio mode

To set the ColorStream HD audio mode:

1 Press Y and open the Setup menu. 2 Highlight ColorStream HD1 Audio (or

ColorStream HD 2 Audio) and press c.

3 Press B or b to select Yes or No and press T to display

the information.

Note: The analog audio terminals for the ColorStream HD and HDMI inputs are used in common. When the ColorStream HD 1 (or 2) audio mode is set to Yes, the HDMI 1 (or 2) audio mode is set to Digital and will be grayed out. When the ColorStream HD 1 (or 2) audio mode is set to No, the HDMI 1 (or 2) Audio changes to Auto.

CH RTNENTER

EXIT

Navigate

Select

Back Exit

Time And Date

Start Setup

Cancel

Time And Date

Manual

TV Guide On Screen

Your TV Guide On Screen system can provide accurate

time and date information.

It is recommended you set up TV Guide On Screen

first and use it to obtain the time and date.

In the event that your TV Guide On Screen system

has acquired time, the television will use network

acquired time rather than manually enterred time.

Cancel

Date (MM/DD/YY)

Time (HH:MM)

Done

Time And Date

:11 11

/06 30/05

Yes

CH RTNENTER

EXIT

Navigate

Select

Back Exit

Installation

Sleep Timer

On/Off Timer

Setup

Auto

ColorStream HD1 Audio

HDMI 1 Audio

ColorStream HD2 Audio

Auto

HDMI 2 Audio

HM196_EN.book Page 28 Tuesday, May 30, 2006 2:18 PM

+ 64 hidden pages