Toro MPR Plus Nozzles Catalogue
MPR Plus Spray Nozzles
• Radius: 5’-15’ (1,5-4,6m)
• Operating Pressure Range: 20-75 psi
(1,4-5,2 Bar)
• Matched Precipitation
MPR Nozzles make design and installation
easier than ever. Just pick your spacing
and choose your arc - the nozzle does
everything else.
MPR Plus Spray Nozzle Series Model List
Model Description Model Description
5’ (1,5m) MPR Plus Nozzle
Red
5Q
5T
5H
5TT
5TQ
5F
8’ (2,4m) Flat Spray
Black
FSQ
FSH
FSF
FSQ-LG
FSH-LG
FSF-LG
12’ (3,7m) MPR Plus Nozzle
90° Arc
120° Arc
180° Arc
240° Arc
270° Arc
360° Arc
90° Arc
180° Arc
360° Arc
90° Arc, Low GPM
180° Arc, Low GPM
360° Arc, Low GPM
Brown
12Q
12T
12H
12TT
12TQ
12F
15’ (4,6m) MPR Plus Nozzle
90° Arc
120° Arc
180° Arc
240° Arc
270° Arc
360° Arc
Black
15Q
15T
15H
15TT
15TQ
15F
(Note: All above also available in Pressure Compensating (PC) Models
90° Arc
120° Arc
180° Arc
240° Arc
270° Arc
360° Arc
8’ (2,4m) MPR Plus Nozzle
Green
8Q
8T
8H
8TT
8TQ
8F
10’ (3,0m) MPR Plus Nozzle
90° Arc
120° Arc
180° Arc
240° Arc
270° Arc
360° Arc
Blue
10Q
10T
10H
10TT
10TQ
10F
Special Patterns
90° Arc
120° Arc
180° Arc
240° Arc
270° Arc
360° Arc
Orange
4SST
4EST
4CST
9SST
4SSST
2SST
Side Strip 4’x30’
(1,2-9,1m)
End Strip 4’x15’
(1,2-4,3m)
Center Strip 4’x30’
(1,2-6,1m)
Side Strip 9’x18’
(2,7-5,2m)
Side Strip 4’x18’
(1,2-5,2m)
Side Strip 2’ x 6’
(0,6-1,8m)
• Side & Corner Specialty Patterns
• Arc Options: 90°, 120°, 180°, 240°, 270°, 360°
• Fit Toro® Spray Bodies
Features & Benefits
Matched Precipitation Rates
Ensure all nozzles (every arc within a family) apply water at
approximately the same rate.
Low Flow Rates
Allow for more sprinklers to be placed on the same zone.
Pre-installed Pressure Compensation Device (PCD)
Eliminate fogging, conserve water and provide precise flow
rates (also available without PC Devices).
Complete Selection Of Arcs
Arcs for all radius options – full, 3/4, 2/3, 1/2, 1/3 and 1/4.
Specifications
Operating Specifications
• Operating pressure range: 20-75 psi (1,4-5,2 Bar)
• Recommended pressure: 30 psi (2,1 Bar)
• Flow Rate: 0.05 – 4.58 GPM (0,2-17,3 LPM)
• Nozzle trajectory:
- 5’: 5° - 8’: 10° - 10’: 17° - 12’: 24° - 15’: 28°
- Corner and Side Strips: 17°
- 8’ Flat Spray: 0°
Additional Features
• Standard and special spray patterns
• Customized screens for each nozzle
• Patterns for small areas: full set of arcs for 10’, 8’ and 5’ (3,0m,
2,4m, and 1,5m) radius nozzles
• 4’ x 18’ (1,2-5,2m) side strip ideal for medians
• 2’ x 6’ (0,6-1,8m) for small planter beds and other narrow areas
• Fine-mesh snap-in filter screens for lower flow nozzles
• Five levels of trajectory
• Convenient nozzle packaging – nozzles and
screens packed separately
• Adjustment screw allows up to 25% reduction in
radius and complete shutoff
Warranty
• Two years
Specifying Information—MPR Plus
XX-XXX-PC
Radius Arc Optional
XX XXX PC
5—5’ (1,5m)
8—8' (2,4m)
10—10' (3,0m)
12—12' (3,7m)
15—15' (4,6m)
Example: A 570 MPR Plus Nozzle with a spray of 10' (3,0m), 180° arc and
Note: To specify a MPR Plus nozzle with a 570Z sprinkler body, attach the body
pressure compensation, would be specified as: 10-H-PC
Note: Do not use PCDs with 570Z PR & 570Z PRX models
° T
Q—90
°
TT—240
EST—End Strip
CST—Center Strip
SST—Side Strip
specification before the above nozzle specification.
—120
Q—270
°
°
H—180
F—360
°
PC—Pressure
°
Compensation
22
Performance Data-MPR Plus Spray Nozzles— US
5' Series with 5° Trajectory—Red
Arc Desc. psi GPM Radius
20 0.05 4 1.40 1.21
90°
120°
180°
240°
270°
360°
5-Q
5-Q-PC
5-T
5-T-PC
5-H
5-H-PC
5-TT
5-TT-PC
5-TQ
5-TQ-PC
5-F
5-F-PC
30 0.09 5 1.61 1.40
40 0.12 6 1.78 1.54
50 0.15 6 1.86 1.62
30-40 0.09 5 1.61 1.40
40-75 0.10 5 1.79 1.55
20 0.07 4 1.47 1.27
30 0.12 5 1.61 1.40
40 0.16 6 1.78 1.54
50 0.20 6 1.86 1.62
30-40 0.12 5 1.61 1.40
40-75 0.13 5 1.79 1.55
20 0.10 4 1.40 1.21
30 0.19 5 1.70 1.47
40 0.23 6 1.70 1.47
50 0.27 6 1.68 1.45
30-40 0.18 5 1.61 1.40
40-75 0.20 5 1.79 1.55
20 0.15 4 1.57 1.36
30 0.25 5 1.68 1.45
40 0.30 6 1.66 1.44
50 0.35 6 1.63 1.41
30-40 0.23 5 1.54 1.34
40-75 0.27 5 1.81 1.57
20 0.20 4 1.86 1.61
30 0.29 5 1.73 1.50
40 0.34 6 1.68 1.45
50 0.40 6 1.66 1.44
30-40 0.26 5 1.55 1.34
40-75 0.29 5 1.73 1.50
20 0.25 4 1.75 1.51
30 0.38 5 1.70 1.47
40 0.45 6 1.66 1.44
50 0.53 6 1.65 1.43
30-40 0.35 5 1.57 1.36
40-75 0.39 5 1.75 1.51
Prec. Rate
12' Series with 24° Trajectory —Brown
Arc Desc. psi GPM Radius
20 0.40 11 1.48 1.28
90°
120°
180°
240°
270°
360°
12-Q
12-Q-PC
12-T
12-T-PC
12-H
12-H-PC
12-TT
12-TT-PC
12-TQ
12-TQ-PC
12-F
12-F-PC
30 0.50 12 1.55 1.35
40 0.60 13 1.64 1.42
50 0.63 13 1.67 1.44
30-40 0.48 12 1.49 1.29
40-75 0.53 12 1.65 1.43
20 0.57 11 1.58 1.37
30 0.72 12 1.68 1.45
40 0.87 13 1.87 1.62
50 0.97 13 1.93 1.67
30-40 0.64 12 1.49 1.29
40-75 0.70 12 1.63 1.41
20 0.95 11 1.76 1.52
30 1.09 12 1.69 1.47
40 1.30 13 1.72 1.49
50 1.55 14 1.77 1.53
30-40 0.96 12 1.49 1.29
40-75 1.05 12 1.63 1.41
20 1.12 11 1.55 1.35
30 1.45 12 1.69 1.46
40 1.63 13 1.75 1.52
50 1.80 13 1.79 1.55
30-40 1.28 12 1.49 1.29
40-75 1.40 12 1.63 1.41
20 1.05 11 1.42 1.23
30 1.55 12 1.61 1.39
40 1.65 13 1.58 1.36
50 1.80 13 1.59 1.38
30-40 1.44 12 1.49 1.29
40-75 1.60 12 1.66 1.44
20 1.67 11 1.54 1.34
30 2.19 12 1.70 1.47
40 2.35 13 1.68 1.46
50 2.70 13 1.79 1.55
30-40 1.92 12 1.49 1.29
40-75 2.10 12 1.63 1.41
Prec. Rate
8' Series with 10° Trajectory —Green
Arc Desc. psi GPM Radius
S
90°
8-Q
8-Q-PC
120°
180°
240°
270°
360°
8-T
8-T-PC
8-H
8-H-PC
8-TT
8-TT-PC
8-TQ
8-TQ-PC
8-F
8-F-PC
20 0.17 7 1.55 1.34
30 0.24 8 1.68 1.45
40 0.26 9 1.61 1.39
50 0.29 9 1.60 1.39
30-40 0.22 8 1.54 1.33
40-75 0.25 8 1.75 1.51
20 0.23 7 1.58 1.36
30 0.30 8 1.57 1.36
40 0.36 9 1.67 1.45
50 0.40 9 1.66 1.44
30-40 0.29 8 1.52 1.32
40-75 0.35 8 1.84 1.59
20 0.37 8 1.47 1.27
30 0.50 8 1.75 1.51
40 0.58 9 1.80 1.56
50 0.65 9 1.80 1.56
30-40 0.44 8 1.54 1.33
40-75 0.50 8 1.75 1.51
20 0.56 7 1.92 1.66
30 0.70 8 1.84 1.59
40 0.80 9 1.86 1.61
50 0.88 9 1.82 1.58
30-40 0.59 8 1.55 1.34
40-75 0.70 8 1.84 1.59
20 0.63 7 1.92 1.66
30 0.76 8 1.77 1.53
40 0.86 9 1.78 1.54
50 0.93 9 1.71 1.48
30-40 0.64 8 1.49 1.29
40-75 0.70 8 1.63 1.41
20 0.74 7 1.69 1.46
30 1.00 8 1.75 1.51
40 1.16 9 1.80 1.56
50 1.30 9 1.80 1.56
30-40 0.85 8 1.49 1.29
40-75 1.00 8 1.75 1.51
15' Series with 28° Trajectory—Black
Arc Desc. psi GPM Radius
S
90°
15-Q
15-Q-PC
120°
180°
240°
270°
360°
15-T
15-T-PC
15-H
15-H-PC
15-TT
15-TT-PC
15-TQ
15-TQ-PC
15-F
15-F-PC
20 0.68 14 1.55 1.34
30 0.85 15 1.69 1.46
40 1.04 16 1.82 1.57
50 1.23 16 2.15 1.86
30-40 0.75 15 1.49 1.29
40-75 0.81 15 1.61 1.40
20 0.95 14 1.75 1.52
30 1.10 15 1.64 1.42
40 1.30 16 1.82 1.57
50 1.45 16 2.03 1.75
30-40 1.00 15 1.49 1.29
40-75 1.10 15 1.64 1.42
20 1.37 13 1.79 1.55
30 1.65 15 1.66 1.44
40 2.02 16 1.77 1.53
50 2.14 16 1.87 1.62
30-40 1.50 15 1.49 1.29
40-75 1.65 15 1.64 1.42
20 1.78 14 1.59 1.38
30 2.20 15 1.64 1.42
40 2.66 16 1.74 1.51
50 2.84 16 1.86 1.61
30-40 2.00 15 1.49 1.29
40-75 2.20 15 1.64 1.42
20 2.10 13 1.85 1.61
30 2.60 15 1.72 1.49
40 3.00 16 1.86 1.61
50 3.40 16 1.98 1.72
30-40 2.30 15 1.53 1.32
40-75 2.50 15 1.66 1.44
20 2.85 13 1.89 1.63
30 3.60 15 1.79 1.55
40 4.20 16 1.84 1.59
50 4.58 16 2.00 1.73
30-40 3.00 15 1.49 1.29
40-75 3.30 15 1.64 1.42
▲ Precipitation rates are for triangular spacing, shown in inches per hour, calculated at 50% of diameter.
■ Precipitation rates are for square spacing, shown in inches per hour, calculated at 50% of diameter.
All performance specifications are based on the stated working pressure available at the base of the sprinkler.
10' Series with 17° Trajectory—Blue
Prec. Rate
Arc Desc. psi GPM Radius
S
90°
10-Q
30-40 0.33 10 1.48 1.28
40-75 0.37 10 1.66 1.43
10-T
30-40 0.44 10 1.48 1.28
40-75 0.50 10 1.68 1.45
10-H
30-40 0.66 10 1.48 1.28
40-75 0.75 10 1.68 1.45
10-TT
30-40 0.89 10 1.49 1.29
40-75 1.00 10 1.68 1.45
30-40 0.99 10 1.48 1.28
40-75 1.09 10 1.63 1.41
10-F
30-40 1.33 10 1.49 1.29
40-75 1.51 10 1.69 1.46
120°
180°
240°
270°
360°
10-Q-PC
10-T-PC
10-H-PC
10-TT-PC
10-TQ
10-TQ-PC
10-F-PC
20 0.30 9 1.66 1.44
30 0.40 10 1.79 1.55
40 0.50 11 1.85 1.60
50 0.60 12 1.86 1.62
20 0.42 9 1.74 1.51
30 0.52 10 1.75 1.51
40 0.65 11 1.80 1.56
50 0.75 12 1.75 1.51
20 0.60 9 1.66 1.44
30 0.71 10 1.59 1.38
40 0.85 11 1.57 1.36
50 0.99 12 1.65 1.43
20 0.71 9 1.47 1.27
30 0.97 10 1.63 1.41
40 1.10 11 1.67 1.45
50 1.19 11 1.65 1.43
20 0.82 9 1.51 1.31
30 1.04 10 1.55 1.34
40 1.20 11 1.62 1.41
50 1.35 11 1.66 1.44
20 1.11 9 1.72 1.49
30 1.49 10 1.67 1.44
40 1.61 11 1.63 1.42
50 1.85 11 1.71 1.48
Prec. Rate
S
Special Patterns—Orange
Prec. Rate
*Specialty arc nozzles are calculated using 2 overlapping nozzles and the total area formula.
Pattern Desc. psi GPM
S
4-EST
4-EST-PC
4-CST
4-CST-PC
9-SST
9-SST-PC
4-SST
4-SST-PC
2-SST
2-SST-PC
4S-SST
4S-SST-PC
Shaded row indicates optimal operating pressure.
20 0.38 3' x 12' 2.03
30 0.45 4' x 15' 1.44
40 0.53 5' x 18' 1.13
50 0.60 6' x 20' 0.96
30-40 0.43 4' x 15' 1.38
40-75 0.50 4' x 15' 1.61
20 0.75 3' x 24' 2.01
30 0.90 4' x 30' 1.44
40 1.04 4' x 30' 1.67
50 1.16 4' x 31' 1.80
30-40 0.86 4' x 30' 1.38
40-75 1.00 4' x 30' 1.61
20 1.00 9' x 18' 1.19
30 1.20 9' x 18' 1.43
40 1.38 9' x 20' 1.48
50 1.55 10' x 22' 1.36
30-40 1.10 9' x 18' 1.31
40-75 1.20 9' x 18' 1.43
20 0.65 4' x 24' 1.30
30 0.90 4' x 30' 1.44
40 1.04 4' x 32' 1.56
50 1.16 5' x 33' 1.35
30-40 0.88 4' x 30' 1.41
40-75 1.00 4' x 30' 1.61
20 0.08 2' x 5' 1.54
30 0.09 2' x 6' 1.44
40 0.10 2' x 7' 1.38
50 0.12 3' x 7' 1.10
30-40 0.09 2' x 6' 1.44
40-75 0.10 2' x 6' 1.61
20 0.46 4' x 17' 1.30
30 0.55 4' x 18' 1.47
40 0.63 4' x 19' 1.60
50 0.71 5' x 19' 1.44
30-40 0.50 4' x 18' 1.34
40-75 0.59 4' x 18' 1.58
Radius shown in feet. Data based on 360°.
Special Patterns
Width Length
Prec.
Rate*
23
Loading...