Toro 133-0246 Installation Instructions
Installation
LooseParts
FormNo.3405-742RevA
BrakeHandleKit
TX1000CompactToolCarrier
ModelNo.133-0246
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato
causecancer,birthdefects,orreproductiveharm.
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
1
2
3
Nopartsrequired
Nopartsrequired
Brakelever1
Washer1
Linkageplate1
Locknut1
1
PreparingtheMachine
NoPartsRequired
Procedure
Qty.
Use
–
–
Preparethemachine.
Removetheexistingparkingbrake.
Installthekitbrake.
1.Movethemachinetoalevelsurface,lowertheloader
arms,shutofftheengine,andremovethekeyfrom
theignitionswitch.
2.Chockorblockthetracksandensurethatthemachine
issecurefrommovement.
©2016—TheT oro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.
OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved
*3405-742*A
2
RemovingtheExistingParking
Brake
NoPartsRequired
Procedure
Note:Unlessindicated,retainallpartstoinstallthekit
parkingbrake.
1.Beneaththeoperator’splatform,unplugthe
auxiliary-switchwireharnessfromthemainwire
harnessofthemachine(Figure1).
Figure1
1.Mainwireharness
2.Auxiliary-switchharness
3.Operator’splatform
Figure3
1.Pin
4.Removethe2bolts(3/8x1inch)securingthelower
covertothemachineandremovethelowercover
(Figure4).
Figure4
1.Lowercover
5.Carefullyunlatchtheloadedspringfromtheboltand
brake-mountplate(Figure5).
2.Bolt(3/8x1inch)
2.Removethe2bolts(5/16x2inches)and2nuts(3/8
inch)securingthepinsintheoperator’splatform
(Figure2).
Figure2
1.Nut(3/8inch)3.Operator’splatform
2.Bolt(5/16x2inches)
3.Removethepinsandtheoperator’ splatform(Figure3).
Figure5
Viewfrombeneaththemachine
1.Spring
2
6.Removethe2cotterpinsand2clevispinsanddetach
thebrakecablesfromthelinkageplate(Figure6).
Figure6
1.Brakecable3.Linkageplate
2.Cotterpin4.Clevispin
9.Discardtheweldedlocknut,linkageplate,washer,and
brakelever.
3
InstallingtheKitBrake
Partsneededforthisprocedure:
1Brakelever
1Washer
1Linkageplate
1Locknut
Procedure
1.Installthebolt(3/8x2-1/4inch)and2nutsontothe
linkageplate(Figure8).
7.Iftheweldedlocknutisstillonandthebrakehandleis
notbroken,breaktheweldsonthelocknut.Remove
theweldedlocknut,linkageplate,washer,andbrake
lever(Figure7).
Figure7
1.Bolt(3/8x2-1/4inch)
2.Nut(3/8inch)
3.Weldedlocknut6.Brakelever
4.Linkageplate
5.Washer
Figure8
1.Bolt(3/8x2-1/4inch)
2.Nut(3/8inch)
3.Locknut6.Brakelever
2.Installthebrakehandle,washer,linkageplate,and
locknut(Figure8).
4.Linkageplate
5.Washer
8.Removeboltand2nutsfromthelinkageplate(Figure
7).
3
Loading...