Form No. 3403-333 Rev B
Trimmer Rack
GrandStand® Mower
Model No. 133-1441
Installation Instructions
Note: If the Low Flow Hydraulic Kit is equipped on |
|
2 |
|
|||
your machine, the trimmer rack cannot be installed. |
|
|
||||
1 |
|
|
||||
|
Installing the Trimmer Rack |
|||||
|
|
|||||
|
|
|
|
|
||
Preparing the Machine |
Parts needed for this procedure: |
|||||
|
|
|
|
|
||
|
|
|
1 |
|
Upper mount bracket |
|
|
|
|
|
|
||
No Parts Required |
|
1 |
|
Lower mount bracket |
||
|
|
|
1 |
|
Upper clamp mount |
|
Procedure |
|
|
|
|
|
|
|
1 |
|
Lower clamp mount |
|||
|
|
|
|
|||
|
|
|
|
|
|
|
1. Park the machine on a level surface. |
|
1 |
|
Large clamp |
||
|
|
|
|
|
||
|
1 |
|
Small clamp |
|||
2. Disengage the PTO. |
|
|
||||
|
|
|
|
|
||
|
1 |
|
Large backer plate |
|||
3. Move the motion-control levers to the |
|
|
||||
|
|
|
|
|
||
|
1 |
|
Small backer plate |
|||
NEUTRAL-LOCK position. |
|
|
||||
|
|
|
|
|
||
4. Engage the parking brake. |
|
2 |
|
Carriage bolt (5/16 inch) |
||
|
|
|
|
|
||
|
2 |
|
Flange nut (5/16 inch) |
|||
5. Shut off the engine and remove the key. |
|
|
||||
|
|
|
|
|
||
|
1 |
|
Spacer |
|||
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
4 |
|
Carriage bolt (1/4 inch) |
|
|
|
|
|
|
|
|
|
|
|
8 |
|
Flange nut (1/4 inch) |
|
|
|
|
|
|
|
|
|
|
|
2 |
|
Hex-head bolt (1/4 x 1-1/2 inch) |
|
|
|
|
|
|
|
|
|
|
|
3 |
|
Hex-head bolt (3/8 inch) |
|
|
|
|
|
|
|
|
|
|
|
5 |
|
Flange nut (3/8 inch) |
|
|
|
|
|
|
|
|
|
|
|
2 |
|
Hex-head bolt (1/4 x 1-1/4 inch) |
|
|
|
|
|
|||
|
|
Note: Adjust the upper and lower plates to fit your |
||||
|
|
trimmer as needed. |
||||
|
|
Installing the Upper Bracket |
||||
|
|
Assembly |
||||
|
|
1. Lower the rear cushion and remove the fuel |
||||
|
|
|
|
tank; refer to your machine Operator’s Manual. |
||
|
|
2. |
Locate and drill a 3/8-inch hole into the pilot hole |
|||
|
|
|
|
on the left side of the machine (Figure 1). |
||
© 2018—The Toro® Company |
Register at www.Toro.com. |
Original Instructions (EN) |
*3403-333* B |
8111 Lyndale Avenue South |
|
Printed in the USA |
|
Bloomington, MN 55420 |
|
All Rights Reserved |
g230753
Figure 1
1.Pilot hole—drill a hole (3/8 inch) here.
3.Use 3 hex-head bolts (3/8 inch), and 3 flange nuts (3/8 inch) to secure the upper mount bracket to the machine (Figure 2).
Torque the bolts to 37 to 45 N∙m (27 to 33 ft-lb).
g230756
Figure 2
1. Flange nut (3/8 inch) |
3. Upper mount bracket |
2.Hex-head bolt (3/8 inch)
4.Use 2 carriage bolts (1/4 inch) and 2 flange nuts (1/4 inch) to secure the upper clamp mount to the upper mount bracket (Figure 3).
Torque the bolts to 10 to 12 N∙m (90 to 110 in-lb).
g230755
Figure 3
1. Carriage bolt (1/4 inch) |
3. Flange nut (1/4 inch) |
2.Upper clamp mount
5.Use 2 hex-head bolts (1/4 x 1-1/2 inch) and 2 flange nuts (1/4 inch) to secure the large backer plate and the large clamp to the upper clamp mount (Figure 4).
Torque the bolts to 10 to 12 N∙m (90 to 110 in-lb).
|
|
Figure 4 |
g230754 |
|
|
|
|
1. |
Flange nut (1/4 inch) |
3. |
Large backer plate |
2. |
Large clamp |
4. |
Hex-head bolt (1/4 x 1-1/2 |
|
|
|
inch) |
|
|
|
|
2
Loading...