Toro 132-3150 Parts Catalogue

Form No. 0453-719

Arctic Cat® Prowler

Installation Instructions - Accessory Kit

Tip-Out Windshield Kit

(p/n 1436-517)

 NOTE: Read these Installation Instructions thoroughly before beginning the installation process. Retain
these Installation Instructions for future reference.

Kit includes:

p/n QTY DESCRIPTION

2441-221 1 Upper Windshield
1441-924 4 Hinge Knob
1441-925 2 Stand-Off Block
1441-926 2 Pivot Block
1441-927 2 Track
* 8 Machine Screw (.5 in 1/4-20)
* 2 Nyloc Jam Nut
1441-929 1 Rubber Strap
1441-930 1 Top Trim
1441-930 1 Bottom Trim
1441-932 1 Double-Sided Trim **
1441-931 1 Center Trim
1441-933 1 Ball Stud
* 12 Flat Washer
* 4 Flange Lock Nut 1/4-20)
* 1 Nyloc Nut (5/16-28)
2441-222 4 Plastic Clamp
2441-223 1 Lower Windshield
* 8 Machine Screw (1.25 in 1/4-20)
2441-224 4 Rubber Clamp
* 1 Adhesive Foam **
2441-385 1 Hardware Kit
0453-719 1 Instructions

*Included in Hardware Kit (p/n 2441-385)
** If ordered, the trim/foam will have to be cut into two equal lengths.

Fig. 1

UTV-127

 NOTE: When installing lower windshield make
sure it is a tight fit between the windshield and the
dash panel.

2. Properly position two Rubber Clamps onto each
side of the front ROPS tubes.

3. With the clamps properly positioned, secure the
lower windshield to the rubber clamps using
four Machine Screws (1.25 in.), four Flat Wash­ers, and four Flange Lock Nuts. Tighten until
snug. Do not over-tighten

.

Installing Lower Windshield

1. Install Adhesive Foam onto the sides of Lower
Windshield. See Fig. 1.

Installing Upper Tip-Out
Windshield

1. Install two Stand-Off Blocks (A) (angle edge
down) onto the top holes on the Upper Wind­shield, using four Machine Screws (.5-in) (B), and
four Flat Washers (C). See Fig. 2.

Fig. 2

UTV-120A

2. Install two Pivot Blocks (D) onto the bottom holes
on the upper windshield, using four machine
screws (.5 in) (B), and four flat washers (C). See
Fig. 3.

Fig. 3

UTV-121A

3. Install Track onto one of the pivot blocks and fas­ten using a Machine Screw (1/4-20 x 1.25-in.) from
the outside, and jam nut from the inside. Repeat for
opposite pivot block.

6. Install Rubber Strap through the slot in upper
windshield and secure around the ball stud. See
Fig. 5.

Fig. 5

UTV-122

 NOTE: Test the upper windshield opened in the
vented and closed positions. When desired fit is
reached, tighten all fasteners in the upper and
lower sections. Do not over-tighten round clamps.

4. Place four Plastic Clamps onto the front ROPS
tubes with the holes in the clamps facing inward.
Lightly fasten each clamp together using the pre­installed screws in each clamp. (Do not tighten
fully at this time.)

5. Align upper windshield with the ROPS bars and
the lower windshield (adjust clamps for proper
alignment). Thread two Hinge Knobs through the
stand-off blocks and into the top mounting location
on the upper clamps. Thread two hinge knobs
through the tracks and into the top mounting loca­tion on the lower clamps. See Fig. 4.

Fig. 4

 NOTE: When the upper windshield is completely
open or closed, the track will snap in place onto the
hinge knobs.

 NOTE: After the windshield is completely
installed, the double-sided trim will need to be cut
for proper clearance around clamps. See Fig. 6.

Fig. 6

UTV-273A

UTV-119A

Printed in the U.S.A. ®™Trademarks of Arctic Cat Inc., Thief River Falls, MN 56701 0713