Toner Cable ODN4P User Manual
Telephone: Nationwide: Fax: E-mail: Internet:
06/07
Draka 6615/6616 Fiber Optic Closures
215-675-2053 800-523-5947 215-675-7543 info@tonercable.com http://www.tonercable.com
969 Horsham Road
Horsham, Pennsylvania 19044 USA
ODN4P®Light Link Series 2
Features
Advanced GaAs RF hybrid technology provides excellent
performance with four individually amplified high level outputs with more than 50 dBmV each at 870 MHz or 1000
MHz.
Suitable for NTSC/PAL analog television transmission,
together with DVB digital television and DOCSIS cable
modems.
Configurable options with one forward receiver or two AB
switching forward receivers and one, two, three or four
return transmitters to suit fibre protection switching and
return path segmentation.
Optional plug-in panel for 4 equalizers to achieve individual
equalization of each RF output port.
Auto-ranging power supply for 38 Vac to 90 Vac coax feeds.
With dedicated KS 5/8? AC input port. No power inserter
needed at the node.
Return pilot for easy alignment and node status monitoring.
Return path lasers are available for 1310 nm or for CWDM
applications in the range of 1510/1530/1550/1570 nm.
The Light Link
®
Series 2, deep fibre Optical Distribution Node
ODN4P is a prime building block for high performance networks, designed for adaptability, scalability and optional return
path segmentation. The configuration options are well suited for
Hybrid Fibre Coaxial (HFC) networks with smaller nodes and
very high traffic handling capability for Internet and telephony.
This node employs advanced modular technology to provide a
cost effective and flexible solution for expanding network architectures.
The optical distribution node may be configured with up to two
optical receivers, two return path optical transmitters and two
power supply units, hence providing network redundancy. The
node incorporates four high RF outputs up to 870 MHz or 1000
MHz.
The ODN4P utilizes the latest in fibre optic technology to
emerge as the final active component in the fibre network.
Designed for fibre-to-the-curb (FTTC) deployment, this node is
also well suited for the last mile in fibre-to-the-premises (FTTP)
applications.
The forward path has redundancy capability with fully automatic AB switching where the forward control model is optioned.
Return path ingress control can be achieved by remotely muting the associated return RF port.
Optical Distribution Node, 1000 MHz Segmented
©Toner Cable Equipment, Inc. Specifications Subject To Change Without Notice.
Telephone: Nationwide: Fax: E-mail: Internet:
Draka 6615/6616 Fiber Optic Closures
215-675-2053 800-523-5947 215-675-7543 info@tonercable.com http://www.tonercable.com
ODN4P Light Link Series 2 Specifications
Forward Path Optical Receiver
Operating Wavelength: 1200 nm to 1600 nm
Optical Input: -4 dBm to +3 dBm
Forward Path RF Amplifier
Bandwidth: Dependent on option -[W]
Option [W]=4254 54 to 1000 MHz
Option [W] = 6585 85 to 1000 MHz
Flatness: ±0.75 dB
RF Test Point Level: -20 dB ±0.5 dB
RF Return Loss: > 16 dB all RF ports
RF Output Level: 39/50/55 dBmV @
16 dB slope to 1000 MHz 54/550/1000 MHz
Forward Path Optical Link *
CNR: >53 dB
64 PAL B/G, D Channels
CSO: >63 dBc
CTB: >67 dBc
42 CENELEC Channels (as per EN50083)
CSO: >64 dBc
CTB: >68 dBc
*Measured with LTM13, 10 km singlemode fiber, 0
dBm input, 4% OMI
Return Path Transmitters **
Laser Type Options:
[Y] = FP Isolated FP laser
1310 nm, 1 mW (0 dBm)
[Y] = DFB Isolated DFB laser
1310 nm, 2 mW (3 dBm)
[Y] = DFB0 Isolated DFB laser
1310 nm, 1 mW (0 dBm)
[Y] = 1510 Isolated CWDM/DFB laser
1510 nm, 2 mW (3 dBm)
[Y] = 1530 Isolated CWDM/DFB laser
1530 nm, 2 mW (3 dBm)
[Y] = 1550 Isolated CWDM/DFB laser
1550 nm, 2 mW (3 dBm)
[Y] = 1570 Isolated CWDM/DFB laser
1570 nm, 2 mW (3 dBm)
Return Path Transmitter RF
Bandwidth:
Option [W] = 4254 5 to 42 MHz
Option [W] = 6585 5 MHz to 65 MHz
Return Segmentation Standard 1 x 4 return
Optional 2 x 2 return***
Optional 4 x 1 return****
Flatness: ±0.5 dB
Return Loss: >16 dB
RF Test Point: -20 ±1 dB
*** 2 x 2 return path configuration requires two separate return path transmitter modules, one for every 2
coax ports.
**** 4 x 1 return path configuration requires four separate return path transmitter modules, one for every
coax port.
Power and Connectors
Optical Connectors: SC/APC, FC/APC, E2000/APC
RF Connectors:
Cable Entry: 5/8” - 24 thread
Internal Connections: 75 ohm Mini SMB
RF Test Points: G-type - male
Power: 38 VAC to 90 VAC
(auto-ranging)
Power Input: Via dedicated power port or
via any of the 4 RF ports
Operating Temperature: -40°C to +65°C
Dimensions and Weight
Dimensions and Weight
Dimensions (H x W x D): 225 x 305 x 240 mm
Ship Size (H x W x D): 350 x 420 x 320 mm
Weight: 10.5 kg
Ship Weight: 13 kg
** Note: Refer to the separate ODNRT-A data sheet
for more detailed specifications on return path laser
transmitters and options. The ODNRT-A may be
ordered separately as a retrofit item or together with
a node.
Loading...