Page 1
OTEB-CO-B
Booster EDFA
969 Horsham Road lHorsham, Pennsylvania 19044 USA l Phone: 215-675-2053 Fax: 215-675-7543 [email protected]
The Olson Technology Model OTEB-CO-B Series EDFA incorporates a reliable optical output drive circuit, and laser TEC to provide a highly reliable
Erbium-doped optical amplifier. Built-in microprocessor software allows the
user to monitor a number of system parameters, including: laser status, systems alarm, network management, TEC circuit operation, etc. If a critical
problem is detected, the power supply for the laser will shut down automatically, a red LED indicator will light, and the front panel display will show the
nature of the problem. Optional SNMP network management is available
through the RS-232 interface. The EDFA is housed in a 1RU 19" rack mount
configuration with an integrated 90-254 Volts AC power supply.
This rugged, low-profile, high-efficiency EDFA design utilizes highly reliable
pump lasers for maximum reliability. The unit accepts a wide optical input
range (-10dBm to +10dBm) and provides a total composite/saturated output
power from +13dBm to +26dBm, depending on the specific model. The
LaserLite Model OTEB-CO-B Series erbium doped fiber amplifier is the perfect companion to the Olson LaserPlus and LaserLite families of 1550nm
EM and DM transmitters and MetroNode and PremiseNode families of
receiver/nodes. It is also designed to operate seamlessly with optical transmitters, receivers and nodes from most leading manufacturers.
Specifically for distribution of
1550nm CATV/video/data in
HFC, PON/AON or FTTH systems.
• Typically used in a launch or midspan application. Optimized for use
with Olson fiber-based DCM.
• Low optical input level requirements
with excellent low noise performance at high output
• 90-254 Volts AC power supply. DC
option not available.
• Optional SNMP monitoring.
• 1540nm to 1560nm wavelength
range
• LED indicators and LCD display for
easy setup and maintenance.
• Single, dual and quad optical output
options
• SC/APC optical connector standard.
Page 2
Specifications Subject To Change Without Notice Rev 06-11 ©Toner Cable Equipment, Inc.
969 Horsham Road lHorsham, Pennsylvania 19044 USA l Phone: 215-675-2053 Fax: 215-675-7543 [email protected]
Min Typ Max Units
Optical Output Power +16 +26 dBm
Optical Input Power -10 +3 +10 dBm
Wavelength 1540 1560 nm
Output Stability ±0.3 dB
Noise Figure (0dBm in) 5.0 dB
Noise Figure (+6dBm in) 6.0 dB
Pump Power Leakage -30 dBm
Reflection Loss -40 dB
Optical Connector SC/APC
Network Management Interface ** RS-232
** SNMP is optional at the time of ordering
Specifications
OTEB-CO-B
Booster EDFA
Min Typ Max Units
Weight 12 lbs
5.5 kg
Dimensions(WxHxD) 19 x 14.2 x 1.75 in
483 x 361 x 44 mm
Min Typ Max Units
AC Power Supply Voltage 90 254 VAC
DC Power Supply Voltage -48 VDC
Operating Temp. Range 0 +50 °C
Storage -20 +65 °C
Humidity 5 90 %
Optical Characteristics (with SM 9/125μm Fiber)
Physical Characteristics
Electrical and Environmental Characteristics
Ordering Information
OTEB-CO-B113x-SA-AC EDFA, 1 Output, +13dBm Optical Output per Port, SC/APC Connector, AC Power
OTEB-CO-B114x-SA-AC EDFA, 1 Output, +14dBm Optical Output per Port, SC/APC Connector, AC Power
OTEB-CO-B115x-SA-AC EDFA, 1 Output, +15dBm Optical Output per Port, SC/APC Connector, AC Power
OTEB-CO-B116x-SA-AC EDFA, 1 Output, +16dBm Optical Output per Port, SC/APC Connector, AC Power
OTEB-CO-B117x-SA-AC EDFA, 1 Output, +17dBm Optical Output per Port, SC/APC Connector, AC Power
OTEB-CO-B118x-SA-AC EDFA, 1 Output, +18dBm Optical Output per Port, SC/APC Connector, AC Power
OTEB-CO-B119x-SA-AC EDFA, 1 Output, +19dBm Optical Output per Port, SC/APC Connector, AC Power
OTEB-CO-B120x-SA-AC EDFA, 1 Output, +20dBm Optical Output per Port, SC/APC Connector, AC Power
OTEB-CO-B121x-SA-AC EDFA, 1 Output, +21dBm Optical Output per Port, SC/APC Connector, AC Power
OTEB-CO-B122x-SA-AC EDFA, 1 Output, +22dBm Optical Output per Port, SC/APC Connector, AC Power
OTEB-CO-B123x-SA-AC EDFA, 1 Output, +23dBm Optical Output per Port, SC/APC Connector, AC Power
OTEB-CO-B124x-SA-AC EDFA, 1 Output, +24dBm Optical Output per Port, SC/APC Connector, AC Power
OTEB-CO-B221x-SA-AC EDFA, 2 Outputs, +21dBm Optical Output per Port, SC/APC Connector, AC Power
OTEB-CO-B419x-SA-AC EDFA, 4 Outputs, +19dBm Optical Output per Port, SC/APC Connector, AC Power
x: Omit = No SNMP, “S” = SNMP
Notes: 1) The list above are common configurations. Other configurations are available. Call factory with questions.
2) Maximum optical output power per port is +24dBm
3) Maximum total optical output power for the OTEB-CO series is +26dBm.
Generalized Part Numbering System
OTEB-CO-Byzzx-SA-AC EDFA, “y” Outputs, “zz” dBm per Output, “x” to select SNMP, SC/APC Connector, AC Power
OTEB-CO-Byzzx-SA-DC EDFA, “y” Outputs, “zz” dBm per Output, “x” to select SNMP, SC/APC Connector, DC Power
Loading...