Toner Cable No 10 Plyseal Tape User Manual
Telephone: Nationwide: Fax: E-mail: Internet:
11/04
Bishop No.10 Plyseal & No.3 Bi-Seal Tape
215-675-2053 800-523-5947 215-675-7543 info@tonercable.com http://www.tonercable.com
969 Horsham Road
Horsham, Pennsylvania 19044 USA
No. 10 Plyseal & No. 3 Bi-Seal Tape
BISHOP
NO. 10 PLYSEAL
Permanently Seal and Protect
Sub-Surface or Overhead Low
Voltage Electrical
Connections
High dielectric strength.
Superior adhesion to metal, all types of rubber
and synthetic cable insulations and jackets.
Impervious to water, salt water, soil and corro-
sive chemicals.
Will not adversely affect cable insulations.
Protect connections when subjected to excessive
flexure.
Unexcelled for cold weather applications.
Description: Bishop No. 10 Electro-Seal compound
has the super adhesive qualities and dielectric
strength to permanently seal all low voltage electrical connections - sub-surface or overhead. It is
impervious to ozone, water, salt water, soil chemicals or other corrosive chemicals. It is unexcelled
for cold weather applications for it is workable from 40° to 80°C, and, also maintains flexibility and a perfect seal even when subject to extreme flexure.
No. 10 Electro-Seal holds fast and permanently to
metal and all types of rubber and synthetic cable
insulation and jackets with no adverse effect on the
cable insulation itself.
Recommended Uses: For encapsulating and protecting all types of sub-surface connectors as well
as all types of overhead connectors, duct seals and
cable end seals.
Packaging: Each roll is boxed.
PROPERTY VALUE UNIT METHOD
Physical
Thickness 0.125 Inches ASTM D-1373
3.175 mm
Tack Excellent Visual *BTM-412
Fusion Excellent Visual *BTM-409
Operating Temp.
Maximum 80 °C *BTM-608
Minimum -40 °C *BTM-607
Chemical
Water Absorption 0.06 % ASTM 570
Ozone Resistance Excellent 0.03% ASTM D1373
Corrosion None Visual ASTM D69
Acid and Alkaline Passed Visual *BTM-814
Electrical
Dielectric Constant 2.6 -- ASTM D150(Hz)
Power Factor 0.02 -- ASTM D150(HZ)
Dielectric Strength 245* Volts/mil ASTM D1373
Volume Resistivity 10
15
Ohm/cm ASTM D257
*245 VPM on tape as manufactured
500 VPM when tested on .020” (508 mm) thick specimen
Data in the table represents average test results, and are not to be used
for specification purposes.
*BTM - denotes Bishop Test Method where no industry standard is
applicable.
No. 10 Plyseal UPC #02626
ROLL SIZE ROLLS PER CASE WEIGHT PER CASE
3 3/4 in x 10 ft 10 31 lbs
95.25 mm x 3.048 m 14 kgs
©Toner Cable Equipment, Inc. Specifications Subject To Change Without Notice.
Telephone: Nationwide: Fax: E-mail: Internet:
Bishop No.10 Plyseal & No.3 Bi-Seal Tape
215-675-2053 800-523-5947 215-675-7543 info@tonercable.com http://www.tonercable.com
NO. 3 BI-SEAL
®
High Voltage Tape
For Insulating, Terminating,
Sealing and Splicing
Self-amalgamating . . . fuses into solid mass
Superior corona and ozone resistance
Long storage life . . . (5 years)
Excellent moisture, corrosion and chemical resis-
tance
High dielectric strength, low-power factor, low
dielectric constant
Superior aging and weathering
Unexcelled for cold weather applications
Exceptional temperature characteristics
Chemically cross-linked
Thermal Emergency Rating 130°C (100 hr/yr)
Description: This cross-linked polyethylene-based
tape exhibits excellent electrical, chemical, mechanical and thermal properties, and is easier to apply
than most insulating tapes.
Bi-Seal conforms perfectly to the most complex
shape or contour. Bi-Seal can be used with the following insulations: oil base rubber, butyl rubber,
EPR, thermoplastic and thermosetting polyethylene,
PVC.
Recommended Uses: For insulating joints and terminations on all types of communication cable. (not
to be used on paper insulated cable.) Insulating
high frequency electronic circuits. Sealing service
entrance connections and corrosion-resistant conduit
couplings.
Packaging: Each roll is labeled, polyethylene
wrapped, and boxed.
PROPERTY VALUE UNIT METHOD
Physical
Color Black -- -Thickness 0.030 inches MIL-I-3825B
0.762 mm
Elongation 1000 % ASTM D-1373
Tensile Strength 300 Psi ASTM D-1373
Operating Temp.
Maximum 95 °C *BTM-608
Minimum -55 °C MIL-I-3825B
Fusion 1 1/2 Turns ASTM D-1373
Chemical
Water Absorption 0.020 % ASTM D-570
Ozone Resistance (1 month) 0.03% MIL-I-3825B
No Effect
Corrosion None Visual MIL-I-3825B
Electrical
Dielectric Constant 2.6 -- ASTM D-150(60Hz)
Power Factor 0.004 -- ASTM D-150(60Hz)
Dielectric Strength 725 Volts/mil ASTM D-149
Volume Resistivity >10
15
Ohm/cm ASTM D-257
No. 3 Bi-Seal®®High Voltage Tape UPC#08052
ROLL SIZE ROLLS PER CASE WEIGHT PER CASE
1 in x 30 ft 80 45 lbs
25.4 mm x 9.1 m 21 kgs
Loading...