Toa N-8650DS User Manual

INSTALLATION MANUAL

IP DOOR STATION N-8650DS

Designed to connect to the IP network, the N-8650DS is an indoor use door station featuring high quality hands-free conversation. It is equipped with 1 contact input and 5 contact outputs, allowing connections to a sensor, electronic lock, and other external equipment. The N-8650DS can be mounted either flush in a wall or on a wall by using the designated mounting box.

3. WALL MOUNTING

2. GENERAL DESCRIPTION

3.1. In-Wall Mounting

Mount the panel mount frame to the YC-150 Back box or 3gang electrical box installed in a wall, then attach the N8650DS to the panel mount frame.

Step 1. Loosen the screw on the N-

8650DS's bottom, then detach the panel mount frame.

Step 2. Mount the panel mount

frame to the YC-150 or electrical box.

3.2. On-Wall Mounting

The N-8650DS comes with 2 types of screws: machine screw M4 x 20 and UNC No.6-32 x 20. For the electrical box provided with unified threads, use the oval head combination screws UNC No.6-32 x 20.

Accessory screws

• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation.

• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or cautions regarding safety.

• After reading, keep this manual handy for future reference.

1. SAFETY PRECAUTIONS

CAUTION

Indicates a potentially hazardous situation which, if mishandled, could result in moderate or minor personal injury, and/or property damage.

• Use the dedicated AC adapter or its equivalent for the unit. Note that the use of other adapter may cause a fire.

Attach the N-8650DS to the YS-13A Wall-mount box installed on a wall.

Step 1. Loosen the screw on the N-8650DS's bottom, then

detach the panel mount frame. (Refer to Step 1 in the previous section.)

Step 2. Mount the panel mount frame to the back box.

The N-8650DS comes with 2 types of screws: machine screw M4 x 20 and UNC No.6-32 x 20. Use the M4 x 20 screw.

Accessory screws

[YS-13A dimensional drawing]

Step 3. Attach the N-8650DS to the panel mount frame.

Hook the tabs on the N-8650DS's upper side into the panel mount frame's slots, fit them into place, then secure the both bottom sides with a screw.

Step 3. Attach the N-8650DS to the panel mount frame.

Hook the tabs on the N-8650DS's upper side into the panel mount frame's slots, fit them into place, then secure the both bottom sides with a screw. (Refer to Step 2 in the previous section.)

Panel mount frame

Ta b

Screw

Screw hole

Bottom view

N-8650DS

Wall surface

Panel mount frame

Wall surface

N-8650DS's bottom

Screw

Rear plate

Install the YC-13A with its bottom plate removed.

YS-13A

Machine screw M4 x 20 (accessory)

6-φ4.5 (for wall mounting) 4-M4 (for N-8650DS mounting)

YC-150 Back box or 3-gang electrical box

Machine screw M4 x 20 (accessory)

163.5

83.5

116.5

Unit: mm

4. WIRING

133-06-303-90

URL: http://www.toa.jp/

Warning

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Traceability Information for Europe (EMC directive 2004/108/EC)

Manufacturer:

TOA Corporation 7-2-1, Minatojima-Nakamachi, Chuo-ku, Kobe, Hyogo, Japan

Authorized representative:

TOA Electronics Europe GmbH Suederstrasse 282, 20537 Hamburg, Germany

Note: Treat unused cables so as not to

short-circuit.

5. ACCESSORIES

UNC No.6-32 x 20 ........................................................... 4

Machine screw M4 x 20 ................................................... 4

LAN coupler ..................................................................... 1

LAN coupler (accessory)

N-8650DS rear

Connection to an external equipment

Contact output 1 (brown)

Contact output 2 (red)

Contact output 3 (orange)

Contact output 4 (yellow)

Contact output COM (purple)

Contact output (blue)

Contact input HOT (gray)

Contact input COM (white)

Speaker cable (black)

* Connection example

Diode

To an indicator or other external equipment

[Specifications] Open collector output Withstand voltage: 30 V DC Max. control current: 50 mA

To an electronic lock or other external equipment*

[Specifications] Relay contact output Withstand voltage: 30 V DC Max. control current: 500 mA

To a switch, sensor, or other external equipment

[Specifications] No-voltage closed contact input. Open voltage: 5 V DC Short-circuit current: 10 mA or less

To external speakers (8 Ω, 0.6 W or more)

External power supply

To network

Network connection AC adapter connection

Can be connected to a network of 10BASE-T/100BASE-TX in auto-sensing. Use a UTP category 5 or more straight through cable with an

To AC mains

Connect the AC adapter*. Use the AD-1210P/1215P (optional) or equivalent. As for the usable adapter, consult your TOA dealer.

Contact output (blue)

RJ-45 connector for this connection.

• Power supply connection ( or )

The following 2 methods are available for supplying power to the station.

• From a DC 12 V AC adapter

• From an IEEE802.3af compliant PoE switching hub (For connection, refer to the instruction manual supplied with the switching hub.)

Relay

24 V DC

GND