Toa N-8640DS User Manual

INSTALLATION MANUAL

IP DOOR STATION N-8640DS

Designed to connect to the IP network, the N-8640DS is an indoor use door station featuring high quality hands-free conversation. It is equipped with 1 control input and 5 control outputs, allowing connections to a sensor, electronic lock, and other external equipment. The N-8640DS can be mounted either flush in a wall or on a wall by using the designated mounting box. The N-8640DS is in full conformity with IP65 water-proof and dust-proof standards. The operating temperature range is –10 to +50°C.

3. WALL MOUNTING

2. GENERAL DESCRIPTION

3.1. In-Wall Mounting

Mount the N-8640DS to the YC-150 or electrical box mounted in the wall.

Note

The wall should be over 12 mm thick, and the opening in the wall for an electrical box should be under 115 mm (wide) by 162 mm (high).

3.2. On-Wall Mounting

The N-8640DS comes with 2 types of screws: machine screw M4 x 20 and UNC No.6 x 20. For the electrical box provided with unified threads, use the oval head combination screws UNC No.6 x 20.

Accessory screws

• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation.

• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or cautions regarding safety.

• After reading, keep this manual handy for future reference.

1. SAFETY PRECAUTIONS

CAUTION

Indicates a potentially hazardous situation which, if mishandled, could result in moderate or minor personal injury, and/or property damage.

• Use the dedicated AC adapter or its equivalent for the unit. Note that the use of other adapter may cause a fire.

Notes

• When controlling an electronic lock with the N-8640DS unit, use "Torx" screws to attach the unit at installation so that it cannot be detached easily.

• When installing the unit outdoors or at locations where it gets wet with water, tightly seal the panel edges. Besides, provide a weep hole at the underside of the mounting box to permit water to drain off.

Mount the N-8640DS to the YS-13A Wall-mount box mounted in the wall.

The N-8640DS comes with 2 types of screws: machine screw M4 x 20 and UNC No.6 x 20. Use the M4 x 20 screw.

Accessory screws

Notes

• When controlling an electronic lock with the N-8640DS unit, use "Torx" screws to attach the unit at installation so that it cannot be detached easily.

• When installing the unit outdoors or at locations where it gets wet with water, tightly seal the edges of the panel and those of the box's rear surface in contact with the wall surface. Besides, make a weep hole (to allow water to exit) in the YS-13A's bottom. (Refer to the figure shown below.)

Wall surface

YS-13A

Seal the panel edges and rear edges (on the wall side).

[YS-13A dimensional drawing]

Be sure to ground both the YC-150 or electrical box, and the frame ground terminal on the unit's rear. Doing otherwise may cause unit failure.

Be sure to ground the frame ground terminal on the unit's rear. Doing otherwise may cause unit failure.

Seal the panel edges.

N-8640DS's front panel

Waterproof washer (accessory)

Wall surface

Wall

Waterproof washer (accessory)

Machine screw M4 x 20 (accessory)

N-8640DS

surface

YS-13A

Make a weep hole (to allow water to exit) in the bottom.

Rear plate

Install the YC-13A with its rear plate removed.

Machine screw M4 x 20 (accessory)

N-8640DS

YC-150 Back box (optional) or 3-gang electrical box

6-φ4.5 (for wall mounting)

4-M4 (for N-8640DS mounting)

163.5

83.5

116.5

Unit: mm

4. WIRING

133-06-302-4B

URL: http://www.toa.jp/

Warning

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Traceability Information for Europe (EMC directive 2004/108/EC)

Manufacturer:

TOA Corporation 7-2-1, Minatojima Nakamachi, Chuo-ku, Kobe, Hyogo, Japan

Authorized representative:

TOA Electronics Europe GmbH Suederstrasse 282, 20537 Hamburg, Germany

Frame ground

LAN coupler (accessory)

N-8640DS rear

Connection to an external equipment

Control output 1 (brown)

Control output 2 (red)

Control output 3 (orange)

Control output 4 (yellow)

Control output COM (purple)

Control output (blue)

Control input HOT (gray)

Control input COM (white)

Speaker cable (black)

* Connection example (When using a 24 V DC relay)

Diode

To an indicator or other external equipment

[Specifications] Open collector output Withstand voltage: 30 V DC Max. control current: 50 mA

To an electronic lock or other external equipment*

[Specifications] Relay contact output Withstand voltage: 30 V DC Max. control current: 500 mA

To a switch, sensor, or other external equipment

[Specifications] No-voltage closed contact input. Open voltage: 5 V DC Short-circuit current: 10 mA or less

To external speakers (8 Ω, 0.6 W or more)

External power supply

Control output (blue)

Network connection AC adapter connection

Can be connected to a network of 10BASE-T/100BASE-TX in auto-sensing. Use a UTP category 5 or more straight through cable with an

Connect the AC adapter*. Use the AD-1210P/1215P (optional) or equivalent. As for the usable adapter, consult

your TOA dealer. RJ-45 connector for this connection.

• Power supply connection ( or )

The following 2 methods are available for supplying power to the station.

• From a DC 12 V AC adapter

• From an IEEE802.3af compliant PoE switching hub (For connection, refer to the instruction manual supplied with the switching hub.)

Relay

24 V DC

GND