Quick
Connect Guide
This guide will help you to set up your system
through several illustrations.
DPL590HT
Speaker Placement
1 Center Speaker:
Positioned on top or below the TV
set.
2 Front Speaker:
Positioned on both sides of the TV
with equal distances away from the
TV.
3 Rear Speaker:
Positioned beside or slightly behind
your favorite viewing position. The
height should be a little above your
ear level.
4 Subwoofer:
Can be positioned anywhere but
preferrably near a wall in the front.
NOTE:
For effective SURROUND effect, rear
speakers need to be located beside
or behind your listening position.
Advanced Set Up:
For more details on speaker
placement, please refer to the
manual chapter “Positioning
Your Speaker”.
For optimized performance, please follow the recommendations and illustration.
THOMSON
46, quai Alphonse Le Gallo
92648 Boulogne
Cedex FRANCE
55987210 (EN)
www.thomson.net
EN
Center Speaker Support
Stand (Optional)
1. Secure the support rod in
place using the screw and
washer provided as
illustrated below.
2. Move the TV support rod
up and down as illustrated
to adjust the height of the
stand. Tighten the screw
to fix the support rod in
place.
Left Rear Speaker
(Surround)
Right Rear Speaker
(Surround)
Left Front Speaker
Center
Right Front Speaker
Subwoofer
3
3
2
2
1
4
DVD
to AUDIO OUT (DVD)
AUDIO INPUT
DVD SAT
TV
VCR
CD
TAPE
DIGITAL AUDIO
COAXIAL OPTICAL
L
R
IN
DVD
DIGITAL AUDIO
COAXIAL OPTICAL
to COAXIAL OUT (DVD)
to OPTICAL OUT (DVD)
COAXIAL
OUT
OPTICAL
OUT
R
L
AUDIO
OUT
Connection described below is also
applicable for any component having
digital output (Cable, Satellite, MD,
CDRW recorder, TV)
NOTE:
• By default, DVD is set to use
Analog.
• After the connections are done,
check the receiver and make sure it
is set to the appropriate input. The
input being used will be displayed
after the source name. (DVD/OPT
means DVD uses Optical Input)
• To change input connection, follow
step 3 to 6 as described below.
• If a COAXIAL cable is used to
connect DVD to the receiver, follow
steps 3 to 6 and select COAXIAL.
DVD To Receiver
Speaker
• Match the speaker wire color
to the speaker / receiver terminals
as shown on the illustration.
• Match the speaker to the
correct terminal on the receiver
(example: left speaker to left
speaker terminal on receiver)
NOTE:
• The color of the wire should be
the same as that on the terminals.
• Connect the striped color wire
to the “-” terminal (both speaker
and receiver)
For details, please refer to
Instruction manual chapter
“Connecting the Speakers”.
Follow the illustration and
instructions provided to
hook up your speakers.
Speakers and FM Antenna
Audio cable
Not Included
Optical Cable (Digital)
Not Included
Coaxial Cable
(75Ω / Digital)
Not Included
Audio Components
Follow the diagram to connect
audio components.
Follow the diagram to connect
your DVD player to receiver.
ANTENNA HOOK-UP
SPEAKER
HOOK-UP
Cables
To help you identify the cables used in audio, illustrations are provided below for your easy reference.
NOTE: To receive Digital signal
(Dolby Digital) either a coaxial or
optical cable must be connected;
and in step 6, you have to select
coaxial or optical input
accordingly.
TV Connections
TVs with RF input may need a RF
modulator (not included) for
inputting audio signals.
VCR
to AUDIO OUT (TV)
AUDIO INPUT
DVD SAT
TV
VCR
CD
TAPE
DIGITAL AUDIO
COAXIAL OPTICAL
L
R
IN
AU
TV
IN
VCR
to AUDIO OUT (VCR)
R
L
1
Antenna and Speaker
Wire Connection
Push terminal tab down to
insert wire.
Release tab to lock wire in
the terminal.
NOTE: Make sure the insulation
is completely removed from the
ends of the Antenna and
speaker wires at all connection
points.
Connect components capable of outputing digital signals like Dolby Digital
(e.g. DVD player or Satelite/Cable Box) or standard PCM format digital signals
(CD player). Read section on “Input Signal Setting” under “Advanced Sound
Control” carefully to adjust the matching input settings.
2
RF modulator
TV
RF cable
Audio cable
The diagram shown above may varies from your actual RF
modulator, please refer to your RF modulator manual.
Audio in
Audio out
RF in RF out
1 Connect either the COAXIAL
or OPTICAL cable (not included).
2 Connect the Audio cable.
3 Select DVD
4 Press SETUP on the remote control.
5 Press the Left or Right adjustment
buttons to select Digital Input setup.
6 Press the Up or Down adjustment
buttons to select the input being
used (analog, coaxial, or optical)
and release to validate.
3
4
5
6
(if available)
Loading...