Simple to Start:
1
ON
OFF
3
ON |
CONFIGURING SYSTEM |
PLEASE WAIT
OFF
1.Press the ON Key.
2.The THERMO KING Logo appears briefly.
3.The startup screen appears while communications are established and the unit prepares for operation.
4. The Standard Display defaults to the “TemperatureWatch” screen after 2-1/2 minutes. The TemperatureWatch Display will remain on until any key is pressed or a check, prevent or shutdown alarm occurs.
NOTE: For more detailed information, see the Operation chapter in the appropriate unit operating manual.
Simple to Set:
CYCLE-SENTRY or Continuous Mode
|
.8°F |
35 |
1 |
ON |
2 & 6 |
||
OFF SET |
35GAUGES SENSORS |
MENU |
|
POINT
3
ON PROGRAMMING CONT MODE
PLEASE WAIT
OFF
5
ON |
NEW SYSTEM MODE IS |
CONTINUOUS
OFF
1.Return to the Standard Display.
2.Press the CYCLE-SENTRY/ Continuous Key.
3.The “Programming Continuous Mode” or “Programming CYCLESENTRY Mode” screen briefly appears.
4.The “New System Mode is Continuous” screen or the “New System Mode CYCLE-SENTRY” screen briefly appears.
5.The Standard Display appears and the heading on top of screen reads the new mode.
6. Pressing the CYCLE-SENTRY/Continuous Key again will change the unit back to the previous mode.
NOTE: For more detailed information, see the Operation chapter in the appropriate unit operating manual.
Simple to Set:
Setpoint Temperature
ON
OFF
2
NEW SETPOINT WILL BE
35.8°F 35 
PRODUCT/ GAUGES SENSORS MENU
SETPOINT
1. Press any key to return to the Standard Display.
ON
40 F
|
+/- TO CHANGE |
+ |
OK? |
|
2. Press the SETPOINT Key on |
OFF |
- |
YES |
NO |
the Standard Display. |
|
|
|
|
|||
|
|
|
|
|
3
3. Press the + or - Keys to change the setpoint reading.
|
|
NEW SETPOINT WILL BE |
|
|
4. Press the YES or NO Key |
||
ON |
|
|
40 F |
|
|
|
|
|
|
|
|
|
4 |
accordingly. |
|
|
+/- TO CHANGE |
|
OK? |
|
|
||
OFF |
- |
+ |
YES |
|
NO |
5. The Standard Display appears |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
with setpoint changed to the new |
|
|
|
|
|
|
|
setpoint. |
|
|
NEW SETPOINT IS |
|
|
5 |
NOTE: For more detailed |
|
ON |
|
|
40 F |
|
|
information, see the Operation |
|
|
|
|
|
|
|
||
OFF |
|
|
|
|
|
|
chapter in the appropriate unit |
|
|
|
|
|
|
|
operating manual. |
Simple to Check:
Gauges
|
|
|
.8°F |
1 |
|
ON |
SET 35GAUGES |
35 |
|
|
OFF |
SENSORS |
MENU |
|
|
|
POINT |
|
|
|
|
|
2 |
|
|
BATTERY VOLTAGE |
|
1. Return to the Standard Display. |
|
ON |
13.8 |
v |
Press the MENUKey. |
|
|
||||
OFF |
EXIT LOCK BACK |
NEXT |
2. Use UP and DOWN soft keys |
|
|
to scroll to the gauges option. |
|
3 |
Press the SELECT Key when |
|
gauges option is highlighted. |
||
|
3. Press BACK or NEXT Keys to scroll through following gauges: Coolant Temperature, Coolant Level, Engine Oil Pressure, Engine Oil Level, Amps, Battery Voltage, Accessory Battery Voltage, Engine RPM, Fuel Level Sensor, Discharge Pressure, Suction Pressure, ETV Position, Fresh Air Exchange, I/O. If no keys are pressed within 30 seconds, the screen will return to the Standard Display.
4.Press the LOCK Key to display any gauge screen for an indefinite period. Press the key again to unlock the screen.
5.Press the EXIT Key to return to the Standard Display.
NOTE: For more detailed information, see the Operation chapter in the appropriate unit operating manual.
Simple to Defrost:
Initiate Manual Defrost
ON |
.8°F |
35 |
2 |
OFF SET |
35GAUGES SENSORS |
MENU |
|
POINT
DEFROST STARTED
ON
|
OFF |
3 |
4 |
|
35 |
|
|
|
|
OFF |
SET GAUGES SENSORS MENU |
|
|
POINT |
1.Return to the Standard Display.
2.Press the DEFROST Key.
3.The display will show “Programming Defrost Please Wait.”
4.The display then shows the Defrost Display. The bar indicator will fill in showing the time remaining to complete the Defrost cycle. When the Defrost cycle is complete the display returns to Standard Display screen.
NOTE: For more detailed information, see the Operation chapter in the appropriate unit operating manual.
Simple to Access:
Sensors
|
|
|
.8°F |
35 |
1 |
|
ON |
SET 35GAUGES |
|
||
|
|
|
|
||
|
OFF |
SENSORS |
MENU |
2 |
|
|
|
POINT |
|
|
|
|
|
|
1. Return to the Standard |
||
|
CONTROL DISCHARGE AIR TEMPERATURE |
Display. |
|
||
ON |
48.3 |
°F |
2. Press the SENSORS Key. |
||
|
|||||
OFF |
EXIT LOCK BACK |
NEXT |
3. Press the BACK or NEXT |
||
|
|||||
|
|
|
|||
|
|
|
Keys to scroll through the |
||
|
|
3 |
following sensor screens: |
||
|
|
|
Control Return Air |
|
|
Temperature, Display Return Air Temperature, Control Discharge Air Temperature, Display Discharge Air Temperature, Temperature Differential, Evaporator Coil Temperature, Ambient Air Temperature, Spare 1 Temperature, Datalogger Temperature Sensors 1-6 and the Board Temperature Sensor. If no keys are pressed within 30 seconds, the screen will return to the Standard Display.
4.Press the LOCK Key to display any sensor screen for an indefinite period. Press the key again to unlock the screen.
5.Press the EXIT Key to return to the Standard Display.
NOTE: For more detailed information, see the Operation chapter in the appropriate unit operating manual.
Simple to Check:
Pretrip Test
|
.8°F |
35 |
2 |
ON |
|
||
35GAUGES SENSORS |
|
|
|
OFF SET |
MENU |
3 |
|
POINT |
|
|
1. Clear all alarm codes.
4
5
7
MAIN MENU
ON |
PRETRIP |
|
|
|
|
LANGUAGE |
|
|
|
||
|
|
|
|
||
|
ALARMS |
|
|
|
|
OFF |
GAUGES |
|
|
|
|
EXIT |
SELECT |
UP |
DOWN |
||
|
|||||
|
|
|
|
4 |
|
ON |
|
PRETRIP |
|
||
|
PASS |
|
|
||
|
|
|
|
||
OFF |
EXIT |
|
|
|
|
2.Return to the Standard Display.
3.Press the MENU Key.
4.Press the UP or DOWN Key as to choose the Pretrip Menu.
5.Press the SELECT Key to start a Pretrip Test.
6.If the unit is not running, a Full Pretrip will be initiated. If the unit is running in either diesel or electric mode, a Running Pretrip will be performed.
7. When all tests are complete, the results are reported as PASS, CHECK or FAIL. If the results are CHECK or FAIL, the accompanying alarm codes will direct the technician to the cause of the problem.
NOTE: For more detailed information, see the Operation chapter in the appropriate unit operating manual.
Simple to Check:
Hourmeters
1
|
ON |
|
.8°F |
35 |
|
OFF |
SET |
35GAUGES SENSORS |
MENU |
|
|
POINT |
|
2 |
|
|
|
|
|
|
MAIN MENU |
|
1. Return to the Standard Display |
|
|
|
screen. |
||
ON |
SENSORS |
|
||
DATA LOGGER |
|
|||
|
HOURMETERS |
|
|
|
OFF |
MODE |
DOWN |
2. Press the MENU Key. |
|
EXIT SELECT UP |
||||
|
|
|
3. Scroll through Main Menu by |
|
|
|
|
repeatedly pressing the UP and |
|
|
4 |
|
DOWN Keys until the hourmeters |
|
|
|
|
Main Menu Screen appears. |
|
4.Press the SELECT Key to enter the Hourmeters Menu.
5.Press the NEXT and BACK Keys to view the Hourmeter Displays.
NOTE: For more detailed information, see the Operation chapter in the appropriate unit operating manual.
Loading...