Thermador VTR630D-01 Installation Guide

Thermedor A, A=_,_c,o,gcon.

,, .......,,__. ,/ i !l.,,..lOi.;

,4X IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS.

This appliance conforms to the relevant safety regulations.

Repairs should only be carried out by qualified specialists.

Improperly executed repairs can give rise to significant hazards for the user.

Z_ Your new appliance was protected on its way to

you by the packaging. None of the materials

cause

pollution to the environment and all can be recy- cled for use again. Please help to protect the environment and dispose of the packaging in an environment-friendly manner.

You can obtain information about the best

method disposing of old appliances and packaging from

your dealer or local municipal council.

Check whether this fan may be combined with the extractor hood.

SAFETY WARNING: Before servicing or cleaning

unit, switch power off at the service panel and

lock service disconnecting means to prevent

power from being switched on accidentally. When the service disconnecting means cannot

be locked, attach a tag to the service panel to

indicate power has been switched off for

maintenance.

WARNING - TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, OR INJURY TO PER- SONS, OBSERVE THE FOLLOWING:

Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-

related construction.

Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturers guideline and safety standards such as those published by the National Fire Protection Association (NFPA),and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local

code authorities.

When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

To properly exhaust air, be sure to duct air out

side. Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces, or garages.

WARNING: To reduce the risk of fire, use only

metal ductwork.

CAUTION - For General Ventilating Use Only. Do Not Use To Exhaust Hazardous Or Explosive Materials And Vapours.

This unit must be grounded.

WARNING: To reduce the risk of fire or electric

shock, do not use this fan with any solid-state speed control device.

Equipment Needed

[] Drill and Bit [] Screwdriver

[] Rubber Mallet

Equipment Included

[] Anchors (4) [] Screws (4)

[] Installation Instructions [] Connector

PAGE 1

PRIOR TO INSTALLATION

Step 1' EXHAUST-AIR MODE

_.s_Exhaust air should neither be directed into a smoke or

exhaust flue that iscurrently used for other purposes, not into a shaft that is used for ventilating rooms in which stoves or fireplaces are also located.

Exhaust air may be discharged in accordance with official and statutory regulations only (e.g. national

building regulations). Local authority regulations must be observed when

discharging air into smoke or exhaust flues that are not otherwise in use.

_:_-_When the extractor hood is operated in exhaust-air

mode simultaneously with a different burner which also makes use of the same chimney (such as gas, oil

or coal-fired heaters, continuous-flow heaters, hot-water boilers) care must be taken to ensure that there is an

adequate supply of fresh air which will be needed by

the burner for combustion.

Safe operation is possible provided that the underpressure in the room where the burner is installed does not exceed

4 Pa (0.04 mbar).

This can be achieved if combustion air can flow through

non-lockable openings, e.g. in doors, windows and via the air-intake/exhaust-air wall box or by other technical measures, such as reciprocal interlocking, etc.

If the air intake is inadequate, there is a risk of poisoning from combustion gases which are drawn

back into the room.

An air-intake/exhaust-air wall box by itself is no guarantee that the limiting value will not be exceeded.

Note: When assessing the overall requirement, the combined ventilation system for the entire household must be taken into consideration. This rule does not apply to

the use of cooking appliances, such as hobs and ovens.

Z_ The fan must be attached at least 78 3/4"from the extractor hood.

Step 2: PREPARING THE WALL

[] The wall must be flat and perpendicular. [] Ensure that the wall is capable of providing a firm hold

for mounting screws and plugs. Weight in kg: 10,3 We reserve the right to construction changes within the

context of technical development.

Z_ When attaching the outer wall fan, ensure that it is accessible for maintenance and repairs.

Z_ The plug-and-socket connections of the electric cables must be located inside the building, according to

local codes. /'_ Do not reduce the 6" diameter of the pipes connected

to the extractor hood.

PAGE 2

+ 4 hidden pages