Repair order and advice on faults . . . . . . . . . . . . .28
en-us
3
en-us Important safety instructions
9Important safety instructions
READ INSTRUCTIONS - DO NOT DISCARD!
(Important safety instructions
Import ant safet y i nstr ucti ons
READ INSTRUCTIONS - DO NOT DISCARD!
Definitions
9 WARNING
Non-observance of this warning could
result in death or serious injuries.
9 CAUTION!
Non-observance of this warning could
result in slight or moderately serious
injuries.
NOTICE: Non-observance of this
information could damage the appliance.
Note: This indicates important information
and/or tips.
About these instructions
■Read and follow the operating and
installation instructions. They contain
important information on how to install,
use and maintain the appliance.
■The manufacturer is not liable if you
disregard the instructions and warnings
in the operating and installation
instructions.
■Retain all documents for subsequent use
or for the next owner.
Introduction
■This appliance complies with the relevant
safety regulations for electrical
appliances.
■The refrigeration circuit has been
checked for leaks.
Risk of explosion
■Never use electric devices inside the
appliance (e.g. heaters or electric ice
makers).
■Do not store products which contain
flammable propellants (e.g. spray cans)
or explosive substances in the appliance.
■Only store high-proof alcohol tightly
closed and standing up.
Risk of electric shock
Improper installations and repairs may put
the user at considerable risk.
■If the power cord is damaged:
Immediately disconnect the appliance
from the power supply.
■Do not use multiple outlets, extension
leads or adapters.
■Before servicing or modifying the
appliance, pull out the power plug or
switch off the circuit breaker.
Before cleaning the appliance, press the
main On/Off switch to switch the
appliance off.
Glass shelves or other fittings can be
safely moved while the appliance is
switched on.
■Never cut through or remove the third
(ground) conductor of the power cord.
■Never defrost or clean the appliance with
a steam cleaner. The steam may
penetrate electrical parts and cause a
short circuit.
■Have the appliance, cable and
accessories repaired or replaced by the
manufacturer, Customer Service or a
similarly qualified person only.
■Use original parts supplied by the
manufacturer only.
The manufacturer guarantees that these
parts satisfy the safety requirements.
4
9Important safety instructions
READ INSTRUCTIONS - DO NOT DISCARD!
Important safety instructions en-us
Risk of cold burns
■Never put frozen food straight from the
freezer compartment into your mouth.
■Avoid prolonged contact of skin with
frozen food, ice and the tubes in the
freezer compartment.
Risk of Injury
Containers which contain carbonated drinks
may burst.
Do not store containers which contain
carbonated drinks in the freezer
compartment.
Avoiding placing children and vulnerable
people at risk
At risk are:
■Children,
■People who have limited physical, mental
or sensory abilities,
■People who have inadequate knowledge
concerning safe operation of the
appliance.
Damage
To prevent damage:
■Do not stand or support yourself on the
base, runners or doors.
■Keep plastic parts and door seals free of
oil and grease.
■Pull the power cord plug – not the power
cord.
Weight
The appliance is very heavy. The appliance
should always be transported and set up by
at least 2 people.
~ "Installation and connection" on page 6
State of California Proposition 65
Warnings
This product can expose you to chemicals
including vinyl chloride, which is known to
the State of California to cause cancer and
birth defects or other reproductive harm.
For more information go to
www.P65Warnings.ca.gov
Measures:
■Never allow children to play with the
appliance.
■Ensure that children and vulnerable
people have understood the hazards.
■Supervise children who are cleaning and
maintaining the appliance.
Risk of suffocation
■If the appliance features a door lock:
keep the key out of the reach of children.
■Keep children away from the packaging
and its parts.
5
en-us Intended use
8Intended use
Intended use
Use this appliance
■only for cooling and freezing food and for making
ice.
■only in the home and in the home environment.
■only according to these operating instructions.
This appliance is intended for use at an elevation of
no more than 2000 meters above sea level.
7Environmental protection
Env i r on ment al prot ec t i on
Packaging
All materials are environmentally safe and
recyclable:
■Dispose of packaging in an environmentally
responsible manner.
■Please ask your dealer or inquire at your local
authority about current means of disposal.
Old appliances
Valuable raw materials can be reclaimed by
recycling old appliances.
5 Installation and
connection
Install ation and connecti on
Contents of package
After unpacking all parts, check for any damage
during transport.
If you have any complaints, please contact the
dealer from whom you purchased the appliance or
our customer service.
~ "Customer service" on page 28
The delivery consists of the following parts:
■Built-in appliance
■Interior fittings (depending on model)
■Installation material
■Instruction manual
■Installation instructions
■Customer service booklet
■Guarantee enclosure
■Information on the energy consumption and
noises
Technical data
Refrigerant, cubic capacity and further technical
specifications can be found on the rating plate.
~ "Getting to know your appliance" on page 9
9 WARNING
CHILDREN MAY BECOME LOCKED IN THE
APPLIANCE AND SUFFOCATE!
Before disposing of your old appliance:
■Remove the door.
■Leave shelves and containers in the
appliance to prevent children from climbing
in.
■Keep children away from the discarded
appliance.
9 CAUTION!
REFRIGERANT AND HARMFUL GASES MAY
ESCAPE.
Do not damage the tubes of the refrigeration
circuit and insulation.
1. Pull out the power cord plug.
2. Cut through the power cord.
3. Have the appliance disposed of properly.
Installing the appliance
Installation location
The weight of the appliance may be up to 460 kg
depending on the model. The base must be
sufficiently stable and should not give. If necessary,
reinforce the bottom.
Check built-in cut-out
The cut-out must fulfill these criteria:
■Anti-tilt bracket must be fitted
■Cut-out depth min. 24” (610 mm), for flush
installation 25” (635 mm)
■rectangular
■stable – the side panels and the top must be min.
5/8" (16 mm) thick and securely attached to the
floor or wall
■Depth of shortest side panels min. 4” (100 mm)
Side-by-side installation
Observe the specifications in the installation
instructions for a side-by-side installation.
If a partition wall is required between the appliances
it must be at least 5/8" (16 mm) wide.
6
Installation and connection en-us
Saving energy
If you follow the instructions below, your appliance will use less power.
Note:
The arrangement of the fittings does not affect the energy consumption of the appliance.
Installing the appliance
Keep the appliance out of direct sunlight.The appliance needs to cool less frequently at low ambient temperaInstall the appliance as far away as possible from heating elements,
cooker and other heat sources:
At least 1¼” (3 cm) from electric or gas cookers.
At least 11¾" (30 cm) from oil or solid-fuel cookers.
NOTICE: If this is not possible, attach an insulating plate between the
appliance and heat source.
Select an installation location at a room temperature of approx. 68 °F
(20 °C).
Do not cover or block the ventilation openings.The appliance needs to cool less frequently if the warm air can
Ventilate the room daily.
Using the appliance
Open the appliance door only briefly. The air in the appliance does not warm up so intensely. The appliance
Transport purchased food in a cool bag and place in the appliance
quickly.
Allow warm food and drinks to cool down before placing in the appli-
ance.
Thaw frozen food in the refrigerator compartment to utilize the low
temperature of the frozen food.
Always leave a space between the food and the back panel.The air can circulate and the humidity will remain constant.The appliPack food airtight.
Do not cover or block the ventilation openings.The appliance consumes less power if the warm air can escape.
Vacuum the ventilation openings once a year.
tures and therefore consumes less power.
escape and therefore consumes less power.
needs to cool less frequently and therefore consumes less power.
ance needs to cool less frequently and therefore consumes less
power.
--------
7
en-us Installation and connection
Before using for the first time
1. Remove information material, adhesive tape and
protective foil.
2. Clean the appliance.
~ "Cleaning" on page 24
Water connection
9 CAUTION!
■Installation and connection of the appliance
must be carried out by authorized technicians
according to the installation instructions
supplied.
■To avoid damage to the appliance and to
ensure its proper functioning, it should only be
connected to a drinking water system.
■To avoid water damage, a shut-off valve must
be installed.
Water pressure of drinking water system
9 CAUTION!
To avoid damage to the appliance, a pressure
relief valve must be installed between the
drinking water connection and the tubing,
should the water pressure exceed the
maximum value.
9 WARNING
RISK OF ELECTRIC SHOCK!
Never use multiple outlets, extension leads
or adapters.
The appliance must be correctly grounded.
Never cut through or remove the third
(ground) conductor of the power cord.
Requirements for outlets
Outlet with 110 V ... 120 V
Protective
60 Hz
conductor
Fuse10 A ... 16 A
Maximum simultaneous load
Appliance6 A
3. Connect the appliance to an outlet near the
appliance.
The outlet must also be freely accessible
following installation of the appliance.
9 WARNING
RISK OF ELECTRIC SHOCK!
If the length of the power cord is inadequate,
never use multiple outlets or extension
leads.Instead, please contact Customer
Service for alternatives.
Note: If the water pressure is too low, this will impair
the relevant functions of the appliance.
■Min. 0.2 Mpa (2 bar / 29 psi)
■Max. 0.8 Mpa (8 bar / 116 psi)
Electrical connection
9 CAUTION!
Do not connect the appliance to electronic
energy saver plugs.
Note: You can connect the appliance to mainscontrolled and sine-controlled inverters.
Mains-controlled inverters are used for photovoltaic
systems which are connected directly to the national
grid. Sine-controlled inverters must be used for
isolated applications. Isolated applications, e.g. on
ships or in mountain lodges, are not directly
connected to the national grid.
1. After installing the appliance, wait at least 1 hour
before connecting it to prevent damaging the
compressor.
2. Connect the appliance via a correctly installed
outlet.
8
*Getting to know your
appliance
Gett i ng to know your appli ance
2-door appliance
Getting to know your appliance en-us
Cheese
3
;
Cheese
C
K
%
#Refrigerator compartment
+Freezer compartment
(Automatic door opening
refrigerator compartment
0 ... P Operating controls
XMain On/Off switch
`Rail for suspending the
Produce Bin
hProduce Bin
)"Shelf for large bottles
)*Vegetable container with
(Automatic door opening
0 ... P Operating controls
XMain On/Off switch
`Rail for suspending the Produce Bin
hProduce Bin
)"Shelf for large bottles
)*Vegetable container with humidity
)jVentilation opening
1"Water filter
1*Door pillar with condensation protection
Operating controls
Getting to know your appliance en-us
â
#
(GLW
@
â
6HWWLQJV
+
3
0Touch fields
There are sensors under the touch fields.
Touching the symbol calls up the
respective function.
8Refrigerator compartment temperature
display
Indicates the set temperature in °C/°F.
@Freezer compartment temperature display
Indicates the set temperature in °C/°F.
H" button
Opens the Settings menu.
~ "Settings menu" on page 11
P: button
Opens the menu for changing the
temperature.
Settings menu
Press the " button to open the menu.
In the Settings menu, you will find:
■Appliance settings
■Cleaning mode
■Vacation mode
■Ice cube production
■Reset water filter counter
■Eco mode
■Self-test
■Sabbath mode (if activated)
~ "Operating the appliance" on page 15
11
en-us Getting to know your appliance
Appliance settings menu
This is how to navigate to the Appliance settings
menu:
1. Press the " button.
2. Scroll to the left to the Appliance settings menu.
3. Open the menu using the 8 button.
In the Appliance settings menu, you will find the
following sub-menus and setting options:
■Brightness
■Key press sound
■Key volume
■Signal tone volume
■Automatic clean lock
■Automatic door opening refrigerator compartment
■Automatic door opening freezer compartment
■Reset water filter
■Prevent condensation (only on 3-door appliance)
■Theater mode
■Temperature unit
■Language
■Factory settings
■Demo mode
■Sabbath mode
~ "Operating the appliance" on page 15
Shelf
You can remove and adjust the shelf:
1. Lift shelf and remove.
2. When re-inserting, insert hooks on back of shelf
at same height to make it level.
Note: Insert shelf carefully to avoid scratching the
appliance.
Interior fittings
(not all models)
Storage compartment
You can remove and adjust the height of the storage
compartments:
1. Lift up the storage compartment and remove.
2. When re-inserting, insert hooks on back of
storage compartment at same height to make it
level.
Note: Insert the storage compartment carefully to
avoid scratching the appliance.
12
Getting to know your appliance en-us
Produce Bin
You can remove the inner container:
■Open the inner container just a gap.
■Lift the inner container and remove it.
You can insert the inner container:
■Guide the suspension of the inner container into
the openings of the outer container.
■Fold the inner container shut.
■Insert the rail for suspending the Produce Bin in
the desired position.
Note: Insert the rail carefully to avoid scratches to
the appliance.
■Insert the Produce Bin into the rail recesses
provided for this purpose.
Container
You can remove the container:
■Press container to the rear,
■lift the container at the rear and remove.
You can remove the Produce Bin:
■Lift the Produce Bin.
■Lift the rail for suspending the Produce Bin and
remove it.
You can insert the Produce Bin:
You can insert the container:
■Pull out telescopic rails all the way
■Place the container on the telescopic rails and
push into the appliance until it engages.
13
en-us Getting to know your appliance
Ice pack
In the event of a power failure or a fault:
■The ice pack delays the warming of stored frozen
food.
Note: The longest storage time is obtained by
placing the ice pack on the food in the top
compartment.
You can take out the ice pack to temporarily keep
food cool, e.g. in a cool bag.
Ice maker
9 CAUTION!
DAMAGE TO THE APPLIANCE!
Never store bottles or food in the ice cube
container, even for short periods. This can
block and damage the ice maker.
Ice cube production starts as soon as the appliance
has reached the set temperature.
Notes
■Discard the first 30-40 ice cubes for hygiene
reasons.
■Ice cube production stops automatically when the
ice cube container is full.
Information about switching ice cube production on
and off
~ "Switching ice cube production on and off"
on page 17
Changing the water filter or replacing with a
particle filter
You can change the water filter, or replace it with a
particle filter. The particle filter can remain in the
appliance permanently: it does not need to be
changed.
Note: After installing a new water filter, discard all ice
cubes produced over the first 24 hours.
1. Turn the cap of the water filter clockwise.
2. Take the water filter out.
3. Remove the protective cap of the new filter.
4. Take off the cap of the old water filter and put it
on the new filter.
5. Slide the new filter to the stop in the filter
opening.
Note: The cap must be horizontal here.
6. Turn the water filter counterclockwise to the stop.
7. When using a water filter: Reset water filter
counter.
~ "Reset water filter counter" on page 17
When using a particle filter: Switch off the water
filter counter.
~ "Switching the water filter counter on and off"
on page 17
8. Discard the ice cubes produced over the first 24
hours.
9. Drain the water out of the old water filter.
Note: You can dispose of the old water filter with
your household garbage.
Water filter
The water filter must be replaced after 6 months at
the latest.
If the ice tastes stale, discard the rest of the ice
cubes and the ones produced over the next
24 hours. If the ice still tastes stale, change the
water filter.
A new water filter or a particle filter can be obtained
from customer service or a specialist dealer.
Note: You can also use the appliance without a
water filter. Replace the water filter with a particle
filter and switch the water filter counter off. There is
no need to change the particle filter.
14
Operating the appliance en-us
1Operating the appliance
Operat i ng the appl i anc e
Switching the appliance on
1. Press the main On/Off switch.
The appliance starts cooling and the light is
switched on when the door is open.
2. Set the required temperature.
~ "Setting the temperature" on page 15
Operating tips
■When the appliance has been switched on, it may
take several hours until the set temperatures have
been reached. Do not put in any food until the
selected temperature has been reached.
■The fully automatic NoFrost system ensures that
the freezer compartment remains free of ice.
Defrosting is not required.
■The front sides of the housing are partly heated
slightly. This prevents condensation in the area
of the door seal.
■If the freezer compartment door cannot be
immediately re-opened after it has been closed,
wait until the resulting low pressure has
equalized.
Switching off and disconnecting the
appliance
Switching off the appliance
Setting the language
1. Press " button to open the Settings menu.
2. Use ( button to move to the menu item Appliance
settings.
3. Press 8 button.
4. Press ( button to move to the menu item
Language.
5. Press : button.
6. Use ( ) buttons to move to the required language.
7. Press 8 button.
The display restarts, and the start screen is
displayed.
Setting the temperature unit
You can choose between the unit °C and °F.
1° <=> 1 °F
1 °C <=> 1 °C
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button.
4. Use < button to move to the menu item
Temperature unit.
5. Press : button.
6. Use < > buttons to move to the required unit.
7. Press 8 button.
The unit will be changed.
8. Press ; button to exit the menu.
■Press the main On/Off switch.
The appliance is no longer cooling.
Disconnecting the appliance
9 CAUTION!
Deterioration in water quality
The water supply must be turned off 3 hours
before disconnecting. This prevents mold
forming with any unused water.
If you do not use the appliance for a prolonged
period:
1. Turn off the water supply to the appliance and
wait 3 hours.
2. Remove groceries.
3. Press the main On/Off switch.
4. Pull out the mains plug or switch off the fuse.
Setting the refrigerator and freezer compartment
temperature
1. To open the menu for setting the temperature,
press the " button.
2. Use the m button to select the desired
compartment.
3. Keep pressing the ¼ button until the display
indicates the required temperature.
4. Confirm the selection by pressing the 8 button. If
the button is not pressed, the appliance stores
the setting and automatically returns to the main
screen after a few seconds.
15
en-us Operating the appliance
Super cooling
Super cooling cools the refrigerator compartment as
cold as possible.
Switch on super cooling, e.g.:
■Before placing large quantities of food into the
compartment
■For cooling drinks quickly
Note: When super cooling is switched on, increased
operating noises may occur.
After approx. 6 hours, the appliance switches to
normal operation.
Switching on super cooling:
1. To open the menu for setting the temperature,
press the : button.
2. Press the / button.
When super cooling is switched on, the symbol /
appears on the display.
3. Confirm the selection by pressing the 8 button. If
the button is not pressed, the appliance stores
the setting and automatically returns to the main
screen after a few seconds.
Switching off super cooling:
1. To open the menu for setting the temperature,
press the : button.
2. Press the > button.
When super cooling is switched off, the symbol /
disappears from the display.
3. Confirm the selection by pressing the 8 button. If
the button is not pressed, the appliance stores
the setting and automatically returns to the main
screen after a few seconds.
Super freezing
Super freezing cools the freezer compartment as
cold as possible.
Switch on super freezing, e.g.:
■to freeze food solid as quickly as possible
■4 ... 6 hours before freezing food weighing 2 kg
or more
■to use the max. freezing capacity
Note: When super freezing is switched on, increased
operating noises may occur.
After approx. 2 ^ days the appliance switches to
normal operation.
Switching on super freezing:
1. To open the menu for setting the temperature,
press the " button.
2. Use the m button to select the desired
compartment.
3. Press the ] button.
When super freezing is switched on, the
symbol
4. Confirm the selection by pressing the 8 button. If
] appears on the display.
the button is not pressed, the appliance stores
the setting and automatically returns to the main
screen after a few seconds.
Switching off super freezing
1. To open the menu for setting the temperature,
press the " button.
2. Use the m button to select the desired
compartment.
3. Press the ] button.
When super cooling is switched off, the symbol
] disappears from the display.
4. Confirm the selection by pressing the 8 button. If
the button is not pressed, the appliance stores
the setting and automatically returns to the main
screen after a few seconds.
Clean lock
You can use this function to switch off the touch
function of the controls for 10 seconds. During this
time you can clean the display.
~ "Cleaning the display" on page 24
1. Press " button to open the Settings menu.
2. Press < button.
The cleaning display appears, and the countdown
starts.
16
Operating the appliance en-us
Automatic clean lock
You can use this function to select whether the
automatic clean lock is switched on automatically
when the door is opened.
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button.
4. Press > button to move to the menu item
Automatic clean lock.
5. To change the setting, press : button.
Vacation mode
If leaving the appliance for a long period of time, you
can switch it over to energy-saving Vacation mode.
Note: The refrigerator compartment temperature is
switched to +57° F (+14° C). Do not store any food
in the refrigerator compartment during this time.
The appliance automatically sets the following
temperatures:
■Refrigerator compartment: +57° F (+14° C)
■Freezer compartment: unchanged
Ice cube production is deactivated.
Switching Eco mode on or off
Switching on:
1. Press " button to open the Settings menu.
2. Use ) button to move to the menu item Holiday
mode.
3. Press < button.
4. Press 8 button.
5. Confirm the following prompt with 8 button and
remove all perishable food items from the
refrigerator compartment.
The temperature is changed, and the display shows
the new temperature.
Switching off:
To switch off holiday mode, press = button on the
start screen.
Switching ice cube production on and off
9 CAUTION!
Damage to the appliance!
Never store bottles or food in the ice cube
container, even for short periods. This can
block and damage the ice maker.
Ice cube production starts as soon as the appliance
has reached the set temperature.
Note: Ice cube production stops automatically when
the ice cube container is full.
Switching ice maker on or off
1. Press " button to open the Settings menu.
2. Use > button to move to the menu item Ice cube
production.
3. Press </= button.
Reset water filter counter
After replacing the water filter, you have to reset the
water filter counter.
1. Press " button to open the Settings menu.
2. Press > button to move to the menu item Reset
water filter counter.
3. Press 8 button to confirm, and confirm the query
again with 8 button.
Note: The water filter counter will not be reset if you
abort the query or take longer than 10 seconds to
make an input.
Switching the water filter counter on and off
If you have replaced the water filter with a particle
filter, switch the water filter counter off. It is not
needed in this case as the particle filter does not
have to be replaced.
1. Press " button to open the Settings menu.
2. Scroll to the left to the Appliance settings menu.
3. Press 8 button.
4. Press > button to move to the menu item Water
filter counter.
5. To change the setting, press : button.
17
en-us Operating the appliance
Eco mode
Eco mode switches the appliance to energy-saving
operation.
The appliance automatically sets the following
temperatures:
■Refrigerator compartment: +43° F (6° C)
■Freezer compartment: +3° F (–16° C)
Switching Eco mode on or off
1. Press the " button to open the Settings menu.
2. Use > button to move to the menu item Eco
mode.
3. Press </= button.
The temperature is changed, and the display shows
the new temperature. When Eco mode is switched
off, the recommended temperature is set.
Note: You can also switch Eco mode on or off by
adjusting the temperature with the +/- buttons.
Self-test
This function can be used to start fault analysis on
your appliance.
~ "Appliance self-test" on page 28
Setting the brightness of the control panel
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button.
4. Press : button to open the menu item
Brightness.
5. Use < > buttons to set the required brightness.
6. Press 8 button.
The setting is saved.
7. Press ; button to exit the menu.
Switching key press sound on or off
You can switch the sounds generated when pressing
keys off and back on again.
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button to open the menu item.
4. Press > button to move to the menu item Key
press sound.
5. Press : button to open the menu item.
6. Use < > buttons to select the required setting.
7. Press 8 button.
The setting is saved.
8. Press ; button to exit the menu.
Setting the key volume
You can adjust the volume level of the sounds
generated when pressing keys.
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button to open the menu item.
4. Press > button to move to the menu item Key
volume.
5. Press : button to open the menu item.
6. Use < > buttons to select the required setting.
7. Press 8 button.
The setting is saved.
8. Press ; button to exit the menu.
Setting the signal tone volume
You can adjust the volume level of the signal tones
generated e.g. with alarms.
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button to open the menu item.
4. Use > button to move to the menu item Signal
tone volume.
5. Press : button to open the menu item.
6. Use < > buttons to select the required setting.
7. Press 8 button.
The setting is saved.
8. Press ; button to exit the menu.
Automatic clean lock
You can use this function to select whether the
automatic clean lock is switched on automatically
when the door is opened.
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button.
4. Press > button to move to the menu item
Automatic clean lock.
5. To change the setting, press : button.
18
Operating the appliance en-us
Automatic door opening
The automatic door opening function supports you in
opening the door.
As soon as you activate this function, automatic door
opening moves out and supports you in opening the
door.
9 CAUTION!
Repeatedly closing the door too early will cause
automatic door opening to fail or wear out.
Do not close the door as long as automatic
door opening is still moved out.
If you have however closed the door, leave it
closed for 5 minutes. Automatic door opening
will re-adjust itself.
Open menu item Auto door opening of refrigerator
compartment:
1. Press " button to open the Settings menu.
2. Press ( button to move to the Appliance settings
menu.
3. Press 8 button to open the menu.
4. Press ) button to move the menu item Auto door
openingj.
5. To change the setting, press : button.
Open menu item Auto door opening of freezer
compartment:
1. Press " button to open the Settings menu.
2. Press ( button to move to the Appliance settings
menu.
3. Press 8 button to open the menu.
4. Press ) button to move the menu item Auto door
openingk.
5. To change the setting, press : button.
Switching on Push-to-open system
In an installation situation without handles you can
select the Push-to-open system. Your appliance will
then open a crack if you press lightly on the door.
Note: Please note that automatic door opening is
disabled if Sabbath mode is activated.
1. Open menu item Auto door opening of
refrigerator compartment or freezer compartment.
2. Select menu item Push-to-open system.
3. Press 8 button to open the menu item.
4. Select Opening force.Here you can select the
level of force required to activate automatic door
opening.
5. Select Opening duration.Here you can select
how long the door should remain open a crack
before it closes again automatically.
Note: If the door only remains open a crack, the
appliance checks once a second whether the door
is still ajar.After the selected opening duration
elapses, the appliance will close the door
automatically.
Switching on Pull-to-open system
In an installation situation with handles you can
select the Pull-to-open system. Your appliance will
support you in opening the door as soon as you pull
on the handle.
1. Open menu item Auto door opening of
refrigerator compartment or freezer compartment.
2. Select menu item Pull-to-open system.
3. Press 8 button to open the menu item.
4. Select menu item Opening force. Here you can
select the level of force required to activate
automatic door opening.
Switching off automatic door opening
1. Open menu item Auto door opening.
2. Select menu item Off.
Switching the water filter counter on and
off
If you have replaced the water filter with a particle
filter, switch the water filter counter off. It is not
needed in this case as the particle filter does not
have to be replaced.
1. Press " button to open the Settings menu.
2. Scroll to the left to the Appliance settings menu.
3. Press 8 button.
4. Press > button to move to the menu item Water
filter counter.
5. To change the setting, press : button.
Switching on or switching off
condensation protection
This function is only available with 3-door
appliances. 3-door appliances are equipped with a
door pillar with condensation protection.
You can open the left-hand door of the refrigerator
compartment without opening the right-hand door
beforehand.
9 CAUTION!
Never unfold the door pillar when the door is
open! It will get jammed when the door is
closed and be damaged or the front panels of
the right-hand door will be damaged.
A heater is built into the pillar to prevent
condensation. This can be switched on or off.
1. Press the " button to open the Settings menu.
2. Use the < button to move to the menu item
Appliance settings.
3. Press 8 button.
4. Press the > button to move to the menu item
Prevent condensation.
5. To change the setting, press the : button.
19
en-us Operating the appliance
Theater mode
If Theater mode is switched on, the light will slowly
become brighter when the appliance is opened, and
then slowly darker when it is closed.
Switching Theater mode on or off
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button to open the menu item.
4. Use > button to move to the menu item Theater
mode.
5. Press : button to open the menu item.
6. Use > button to move to the menu item On or Off.
7. Press 8 button.
The setting is saved.
8. Press ; button to exit the menu.
Resetting to the factory settings
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button.
4. Use < button to move to the menu item Factory
settings.
5. Press : button.
A signal tone sounds, and a message to confirm
reset appears.
6. Press 8 button.
All settings are reset to the factory settings.
7. Press ; button to exit the menu.
Switching demo mode on or off
The cooling function of the appliance is switched off.
All other functions can be used.
Note: Do not store any food items in demo mode as
the appliance remains at room temperature.
1. Press " button to open the Settings menu.
2. Use ( button to move to the menu item Appliance
settings.
3. Press 8 button.
4. Press ( button to move to the menu item Demo
mode.
5. Press : button.
6. Use ( ) buttons to select the setting On or Off
7. Press 8 button.
The setting is saved.
8. Press ; button to exit the menu.
Sabbath mode
The appliance switches off the following:
■Automatic door opening
Note: With handle-free installation, please note that
you will not be supported when opening the door
during this time.
To open the door in this case, reach from below
under the bottom panel of the unit.
■Ice maker
■Audible signals
■Interior light
■Messages on the control panel
■Background illumination of control panel is
reduced
Switching Sabbath mode on or off
Displaying Sabbath mode in the Settings menu
To use Sabbath mode, you first have to display the
function in the Settings menu:
1. Press " button to open the Settings menu.
2. Press ( button to move to the Appliance settings
menu.
3. Press 8 button.
4. Press ( button to move to the menu item Sabbath
mode. Press : button.
5. Press ( button to move to the menu item
Available.Confirm by pressing 8 button.
The function is added to the Settings menu.
Switching on Sabbath mode
1. Press " button to open the Settings menu.
2. Press › button to open the view Duration
Sabbath mode.
3. Select one of the presettings, or change the
duration with the ¼SY## buttons.
4. Press < button to start.
The appliance switches all listed functions off.
Switching Sabbath mode off
■After the selected time elapses, the appliance
switches over to normal operation.
■To end Sabbath mode before expiry of the
selected time, press = button.
20
Alarm en-us
MAlarm
Al a r m
Door alarm
If the appliance door is open for a long time, the
door alarm (continuous audible signal) switches on.
■Close door.
The audible warning signal is switched off.
URefrigerator
compartment
Refr i ger at or compart ment
The refrigerator compartment is suitable for storing
meat, sausages, fish, dairy products, eggs, ready
meals and pastries.
The temperature can be set from +36 °F (+2 °C)...
+46 °F (+8 °C).
The refrigerator compartment can also be used to
store highly perishable groceries in the short to
medium term. The lower the selected temperature,
the slower the enzymatic and chemical processes
and deterioration by microorganisms. A temperature
of +37 °F (+4 °C) or lower ensures optimum
freshness and safety of the stored groceries.
Note when storing food
Note: Avoid contact between food and the back
panel.
Otherwise, the air circulation will be impaired and
food or packaging may freeze to the back panel.
■Store fresh, undamaged food.
The quality and freshness will then be retained for
longer.
■In the case of ready products and bottled goods,
do not exceed the minimum sell-by date or useby date indicated by the manufacturer.
■To retain aroma, color and freshness, pack
or cover food well before placing it into the
appliance.
This will prevent flavors being transferred
between foods and the plastic parts from
becoming discolored.
■Leave warm food and drinks to cool down before
placing them into the refrigerator compartment.
Note the chill zones in the refrigerator
compartment
The air circulation in the refrigerator compartment
creates different chill zones.
Coldest zone
The coldest zone is in the interior at the back panel
and in the chill compartment.
Note: Store delicate food (e.g. fish, sausages and
meat) in the coldest zone.
Warmest zone
The warmest zone is at the very top of the door.
Note: Store e.g. hard cheese and butter in the
warmest zone. Cheese can continue to release its
aroma and the butter will still be easy to spread.
Vegetable container with humidity
controller
The vegetable container is the optimum storage
location for fresh fruit and vegetables.You can adjust
the humidity in the vegetable container via the
humidity controller and a special seal. This allows
fresh fruit and vegetables to be stored up to twice as
long as with conventional storage.
The humidity in the vegetable container can be set
according to the type and quantity of products to be
stored:
■Mainly fruit as well as for a large load – set lower
humidity with controller position FRUIT
■Mainly vegetables as well as for a mixed or small
load – set higher humidity with controller position
VEGETABLES
Notes
■For optimum preservation of quality and flavor
store fruit sensitive to cold (e.g. pineapple,
banana, papaya and citrus fruit) and vegetables
sensitive to cold (e.g. eggplant, cucumbers,
zucchini, peppers, tomatoes and potatoes)
outside of the appliance at temperatures of
approx. +46 °F (+8 °C) ... +54 °F (+12 °C).
■Condensation may form in the vegetable
container depending on the type and quantity of
products stored.
Remove condensation with a dry cloth and adjust
the humidity in the vegetable container with the
humidity controller.
Chill compartment
The chill compartment has lower temperatures than
the refrigerator compartment. Temperatures below
+32 °F (0 °C) may occur.
Ideal for storing fish, meat and sausage. Not suitable
for salads, vegetables and groceries sensitive to
cold.
The temperature in the chill compartment can be
adjusted.
21
en-us Freezer compartment
WFreezer compartment
Freez er compar t ment
The freezer compartment is suitable for:
■storing frozen food
■making ice cubes
■freezing food
The temperature can be set from -11 °F (24 °C)... +7 °F (-14 °C).
The freezer compartment can be used to store
perishable foods long-term almost without any
noticeable reduction in quality, as the low
temperatures considerably slow down or stop
deterioration. Appearance, flavor and all valuable
ingredients are largely retained.
The time between putting fresh food in the freezer
compartment and it freezing solid depends on the
following factors:
■temperature set
■type of food
■amount of food in the freezer compartment
■quantity and type of storage
Fully utilizing the freezer volume
To place the maximum quantity of frozen food in the
freezer compartment:
■Remove all fittings.
■Store food directly on the shelves and on the floor
of the freezer compartment.
Purchasing frozen food
■Ensure the packaging is not damaged.
■Check there is a sell-by date.
■The temperature in the supermarket freezer must
be 0 °F (-18 °C) or lower.
■Do not interrupt the freezing chain. If possible,
transport frozen food in a cool bag and place in
the freezer compartment quickly.
When loading products
■Freeze large quantities of food in the top
compartment.
This is where it will freeze especially quickly and
gently.
■Distribute food in the compartments or frozen
food containers.
■Do not bring food which is to be frozen into
contact with frozen food.
If required, restack frozen food in the frozen food
containers.
■Important for unrestricted air circulation in the
appliance:
push in frozen food containers up to the limit
stop.
Freezing fresh food
Freeze only fresh and undamaged food.
Food which is boiled, fried or baked is more suitable
for freezing than food which is eaten raw.
Before freezing food, make preparations appropriate
to the food in order to retain the best possible
nutritional value, flavor and color:
■Vegetables: wash, chop, blanch.
■Fruit: wash, pit and perhaps peel, possibly add
sugar or ascorbic acid solution.
Information on how to do this can be found in
relevant literature.
Suitable for freezing
■Baked goods
■Fish and seafood
■Meat
■Poultry and game
■Vegetables, fruit and herbs
■Eggs without shells
■Dairy products, e.g. cheese, butter and quark
■Ready meals and leftovers, e.g. soups, stews,
cooked meat and fish, potato dishes, soufflés and
desserts
22
Not suitable for freezing
■Types of vegetables which are usually eaten raw,
e.g. lettuce or radishes
■Unpeeled or hard-boiled eggs
■Grapes
■Whole apples, pears and peaches
■Yoghurt, soured milk, sour cream, creme fraiche
and mayonnaise
Freezer compartment en-us
Packing frozen food
The correct type of packaging and material selection
are decisive factors in the retention of the product
quality and prevent the development of freezer burn.
1. Place food in packaging.
2. Remove air.
3. Pack food airtight to prevent it from losing flavor
or drying out.
4. Label packaging with contents and date of
freezing.
Suitable packaging:
■Plastic foil
■Tubular foil made of polyethylene (PE)
■Aluminum foil
■Freezer containers
Suitable closures:
■Rubber bands
■Plastic clips
■Cold-resistant adhesive tape
Unsuitable packaging:
■Wrapping paper
■Greaseproof paper
■Cellophane
■Garbage bags and used grocery bags
Thawing frozen food
The thawing method must be adjusted to the food
and application in order to retain the best possible
product quality.
Thawing methods:
■in the refrigerator compartment (especially
suitable for animal-based foods such as fish,
meat, cheese, quark)
■at room temperature (bread)
■in the microwave (food for immediate
consumption or immediate preparation)
■in the oven/cooker (food for immediate
consumption or immediate preparation)
9 CAUTION!
Do not refreeze partly or completely thawed
food. You can only refreeze food once it has
been cooked (boiled or fried).
The frozen food can no longer be stored for the
maximum duration.
Shelf life of frozen food at 0 °F (-18 °C)
Fish, sausage, ready meals,
up to 6 months
and cakes and pastries:
Meat, poultry:up to 8 months
Vegetables, fruit:up to 12 months
23
en-us Defrosting
=Defrosting
Defrosting
Freezer compartment
The fully automatic NoFrost system ensures that the
freezer compartment remains free of ice. Defrosting
is no longer required.
DCleaning
Cleani ng
9 CAUTION!
AVOID DAMAGING THE APPLIANCE AND THE
FITTINGS.
■Do not use abrasive, chloride or acidic
cleaning agents or solvents.
■Do not use scouring or abrasive sponges.
The metallic surfaces may corrode.
■Never clean the shelves or containers in the
dishwasher.
The parts may become deformed.
Cleaning the fittings
To clean, take the variable parts out of the
appliance.
~ "Interior fittings" on page 12
Care instructions for stainless steel
surfaces
When taking care of and cleaning stainless steel
surfaces, use only cleaning agents suitable for
stainless steel and a stainless steel cleaning cloth.
You can purchase a suitable stainless steel cleaning
cloth from customer service.
To prevent visible scratches, clean the stainless
steel surface in the direction of the structure.
Cleaning the display
The change in temperature and humidity can cause
the controls to steam up.
Switch the clean lock on before cleaning.
~ "Clean lock" on page 16
Use a clean micro-fiber cloth for cleaning.
Cleaning the appliance interior
Proceed as follows:
1. Press the main On/Off switch.
2. Take out food and store in a cool location.
Place ice pack (if available) on the food.
3. Clean the appliance with a soft cloth, lukewarm
water and a little pH-neutral washing-up liquid.
9CAUTION!
The rinsing water must not run into the light
or through the drainage hole into the
evaporation area.
4. Wipe door seal with clear water and dry
thoroughly with a cloth.
5. Switch appliance back on and put in food.
24
Odors en-us
lOdors
Odors
If you experience unpleasant odors:
1. Switch off the appliance with the main On/Off
switch.
2. Take all food out of the appliance.
3. Clean the inside.
~ "Cleaning" on page 24
4. Clean all packaging.
5. Seal strong-smelling food in order to prevent
odors from forming.
6. Switch the appliance on again.
7. Store food in the appliance.
8. Check whether the formation of odors is still
occurring after 24 hours.
9. Change the odor filter.
~ "Changing the odor filter" on page 25
Changing the odor filter
Replacement filters are available from your customer
service.
1. Open the filter holder with a slotted screwdriver.
3. Close the filter holder.
9Lighting
Li ght i ng
Your appliance features a maintenance-free LED
light.
Only customer service or authorized technicians may
repair the light.
2. Remove the used odor filter and replace with a
new odor filter.
>Noises
Noi s e s
Normal noises
Droning: A motor is running, e.g. refrigerating unit,
ventilator.
Bubbling, buzzing or gurgling: Refrigerant is
flowing through the tubes.
Clicking: Motor, switches or solenoid valves are
switching on or off.
Cracking: Automatic defrosting is running.
Preventing noises
Appliance is not level: Align appliance using a
water level. If required, place a little packing
underneath.
Containers, shelves or storage compartments
wobble or stick: Check the removable fittings and
re-insert if required.
25
en-us Faults – what to do?
3 Faults – what to do?
Faul t s – wha t to do?
Before you call customer service, use this table to check whether you can rectify the fault yourself.
Appliance
Temperature differs greatly from the set value.
Switch off appliance for 5 minutes.
~ "Switching off and disconnecting the appliance" on page 15
If the temperature is too warm, check temperature again after a
couple of hours.
If the temperature is too cold, check temperature again on the
following day.
Displays do not illuminate.
The mains plug has not been inserted properly.Connect the mains plug.
The fuse has tripped.Check the fuses.
The power has failed.Check whether the power is on.
The refrigeration unit is switching on more frequently and for longer.
The appliance was opened frequently.Do not open the appliance unnecessarily.
The ventilation openings are covered up.Remove obstacles.
Large quantities of fresh food have been put in.Switch on super cooling promptly in advance.
Appliance is not cooling, display and lighting are lit.
Demo mode is switched on.Switch demo mode off.
~ "Switching demo mode on or off" on page 20
The door does not open when pressed.
A special mode has switched off automatic door opening.To open the door, reach from below under the bottom panel of
the unit or switch off special mode.
~ "Switching Sabbath mode on or off" on page 20
Pull-to-open is switched on.Switch the appliance to Push-to-open.
~ "Automatic door opening" on page 19
The opening force is set too high.Select a lower setting for the opening force.
The fuse has tripped.Check the fuses.
The power has failed.Check whether the power is on.
--------
26
Loading...
+ 58 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.