Thermador T24UR905RP, T24UR905LP, T24UR915RS, T24UR915LS, T24UR925RS INSTALLATION GUIDE
Page | 1
INSTALLATION
GUIDE
GUIDE
D'INSTALLATION
GUIA DE
INSTALACION
Model/Modele/Modelo
T24UR925RS
T24UR925LS
T24UR915RS
T24UR915LS
T24UR905RP
T24UR905LP
Glass Door Refrigerator
Verre
Refrigerador Puerta de Vidrio
Porte Frigo
Page |2
IMPORTANT:
Before you begin, read these instructions completely and
carefully.
INSTALLER:
OWNER:
Please leave this manual with owner for future reference.
Save these installation instructions for local electrical
inspector’s use and for future reference.
Table of Contents
Important Safety Instructions ….…………. 3
- Inspect the Glass Door Refrigerator
Tools needed for installation ……………..
Materials supplied …………….………….…
Installing the appliance ……………………. 5
- Transporting
- General measures
- Installation location
- Installing Side-by-Side
Ventilation …………………………………….
Connecting the appliance ………………… 9
- Electrical connection
Door opening …………………………………
Installing the anti-tip-brackets ……………..
Installing the overlay frame ……………….. 17
Customer Service Information ……………
Addendum A ………………………………… 22
4
4
9
11
13
21
Page | 3
Important Safety Instructions
READ AND SAVE THESE INSTRUCTIONS!
These installation instructions are intended for use by qualified installers.
In addition to these instructions, the appliance shall be installed:
•
In the United States, in accordance with the
National Electric Code/State and municipal
codes and/or local codes.
•
In Canada, in accordance with the Canadian
Electric Code C22.1 – latest edition/Provincial
and Municipal codes and/or local codes.
Be sure to observe all listed warnings and cautions.
Look for the triangles with exclamation marks inside.
WARNING:
This indicates that death or serious
CAUTION:
This indicates that minor or moderately severe injury may result due to non-observance of this
warning.
NOTE:
This is used to draw the user’s attention to something in particular.
injury may result due to non-observance of this warning.
.
Important
•
NEW INSTALLATION – If the appliance is a new installation, most of the work must be
done before the unit is moved into place.
•
REPLACEMENT – If the appliance is replacing another appliance, the connections for
the appliance being replaced must be checked for compatibility with the new unit and
replaced as necessary.
Inspect the Glass Door Refrigerator
Remove all tape, packaging and plastic covers.
After unpacking the appliance and prior to installation, thoroughly inspect the Glass Door Refrigerator for
possible freight or cosmetic damage. Report any damage immediately.
NOTE: Please do not discard any bags or items that come with the original package until after the entire
installation has been completed!
Page |4
Tools needed for installation
Tape Measure Philips Screwdriver Level
These are the tools that you may need for the installation of the appliance. However, if you need to
modify the counter or cabinetry to fit the unit, you may need other tools to make counter/cabinetry
modifications before installing the appliance.
Materials supplied
Anti-tip-bracket. 2 pieces.
Screws: 2 pieces.
Door Stopper Pin: 1
1 Insulating Foam (Not
(3mm)
1/2”
(740mm)
illustrated) 20
(520mm) x 29 1/8”
x 1/8”
Screws for Overlay Panel:
ART001T73840 (TRUSS M4X34
TAPPING). 8 pieces. ONLY FOR
T24UR905LP AND T24UR905RP
MODELS.
Page | 5
Installing the appliance
Most of the installation work must be done before the Glass Door Refrigerator is moved into place.
Have a qualified technician install and connect the appliance according to the enclosed installation
instructions.
WARNING:
Do not install this appliance:
- Outdoors
- In an environment with dripping water
- In rooms where there is a risk of frost
Transporting
The appliance is heavy and must be handled with caution during transportation and installation.
Because of the weight and dimensions of the appliance, at least two persons are necessary to move the
appliance into position securely and avoid injuries to people or damage to the appliance.
General measures
Note: With the legs fully
retracted the appliance has a
minimum dimension of 34 3/8”
from top to bottom. The legs
can be extended up to 1/2”
(13mm).
Measurements in inches (mm)
All legs are adjustable by up to ½ inch.
Page |6
Installation location
A dry, well ventilated room is suitable as an installation location. The installation location should not be
exposed to direct sunlight and not placed near a heat source, e.g. a cooker, radiator, etc.
If installation next to a heat source is unavoidable, use a suitable insulating plate or observe the following
minimum distance from the heat source:
To electric or gas oven/range 1¼” (3 cm).
▪
▪
To an oil or coal-fired cooker 1113/16” (30cm).
▪
To another Refrigerator or Wine Reserve 1” (2.54cm).
The floor of the installation location must not give way; if necessary, reinforce floor. The appliance must
be upright and level to function correctly.
For proper operation and appearance of the unit, the cabinet opening should be square and have
dimensions as shown in the next diagrams.
TOP VIEW
FRONTAL VIEW
Page | 7
TOP VIEW OPEN RIGHT SWING
TOP VIEW OPEN LEFT SWING
Page |8
Installing Side-by-Side
The appliance can be installed next to another Thermador appliance. Follow the next dimensions and
notes for the correct installation of the appliance in a side-by-side layout.
NOTE: Before placing the unit into the niche, adhere the Insulating Foam (included with the product) on
the side of the unit that will be placed next to the additional appliance. Be sure that the Insulating Foam is
even with the surface of the unit and that there are no bubbles or bumps on the Insulation Foam after
adhering it to the unit.
Side of the unit next to
the other appliance.
Insulating Foam
Included with the unit.
Install the appliances in a “French Door” configuration; appliances with Left Hinge should be
opposite to another with Right Hinge.
Loading...