Thermador T18ID80NLP/48, T24IR70NSP/42, T24IF70NSP/46, T24ID80NRP/47, T24ID80NLP/47 Installation Guide

...

INSTALLATION

T18 ....

INSTRUCTIONS

INSTRUCTIONS D'iNSTALLATION

INSTRUCCIONES

DE INSTALACION

T24 ....

T30 ....

9000 561 742

Thermedor _

INSTALLATION INSTRUCTIONS ................................................................................ 4

INSTRUCTIONS D'INSTALLATION ............................................................................. 41

INSTRUCCIONES DE INSTALACION .......................................................................... 79

Table of Contents

Safety and warning information ........................... 5

Installation options ............................................... 6

Individual unit .......................................................... 6

Side-by-Side ........................................................... 6

Individual appliances with partition .......................... 6

At the end of the kitchen units ................................ 6

Installation ............................................................. 7

Installation room ..................................................... 7

Installation cavity ..................................................... 7

Furniture/fixtures ..................................................... 7

Installation

Instructions ........................................ 18

Checking the installation cavity .......... 18

Transport of the appliance ................. 18

Removing the packaging ................... 19

Installation preparation ...................... 19

Changing over the door hinges .......... 19

Preparing the installation cavity .......... 22

Attaching an alternative anti-tip device 23

Preparing to connect the water ......... 24

Attaching the edge protection ........... 24

10,

Side-by-Side installation .................... 24

11,

Pushing the appliance into the

installation cavity ...............................

Base ....................................................................... 7

Connecting the power .......................................... 8

onnecting the water .............................................. 8

Installation dimensions ......................................... 9

Single installation .................................................... 9

Side-by-Side installation .......................................... 10

Water connection ................................................... 11

Appliance dimensions .......................................... 12

18" Appliance (Freezer/Freezer with Ice and

Water dispenser) ..................................................... 12

18" Appliance (Wine unit) ........................................ 13

24' Appliance (Refrigerator/Freezer/Freezer

with Ice and Water dispenser) ................................. 14

24' Appliance (Wine unit) ........................................ 15

30" Appliance (Refrigerator/Freezer/Freezer

with Ice and Water dispenser) ................................. 16

Required accessories and tools .......................... 17

Supplied accessories .............................................. 17

Optional accessories .............................................. 17

Other required accessories from specialist outlets ,, 17

Tools ...................................................................... 17

Other ...................................................................... 17

12, Installing and aligning the appliance ,,, 26 13, Attaching the appliance to the

top of the cavity ................................. 27

14, Attaching the individual appliance

to the side of the cavity ...................... 27

15, Checking that the finger guard

moves easily ...................................... 28

16, Connecting the water to the appliance 28

17, Attaching the toe kick panel .............. 29

18, Commissioning the Appliance ........... 30

19, Preparing the furniture doors ............. 30

20, Loading the appliance door ............... 31

21, Attaching the adjusting rail

to the furniture door ........................... 32

22, Attaching and aligning

the furniture door ............................... 33

23. Attaching the furniture door ............... 34

24, Attaching the lower bracket ............... 35

25, Attaching the finger guard ................. 36

26, Attaching the covers .......................... 36

27, Aligning the ice-water dispenser ........ 38

28, Attaching the cover strips .................. 39

29, Mounting of air separator ................... 40

30, Adjusting the door opening angle ...... 40

31, Changing the door spring .................. 40

Before you Begin

Read these instructions completely and carefully.

WARNING General

These appliances are top-heavy and must be secured to

prevent the possibility of tipping forward. Anti-tip protection is required.

Keep doors closed until the appliance is completely installed and secured per installation instructions.

Due to the weight and size of this appliance, and to reduce the risk of persona[ injury or damage to the product - TWO PEOPLE ARE REQUIRED FOR PROPER

INSTALLATION. This appliance must be properly grounded. See the section

on "Connecting the power" on page 8.

Use this appliance only for its intended purpose.

Immediately repair or replace e[ectdc service cords that

become frayed or damaged.

Unplug the appliance or switch off the fuse before cleaning

or making repairs.

Repairs should be made by a qualified service technician.

CAUTION

Skill- Level- Installation of this appliance requires basic

mechanical, carpentry and plumbing skills.

Proper installation is the responsibility of the installer.

Product failure due to improper installation is not covered

under the Appliance Warranty.

See the Owner's Manual for warranty information.

A IMPORTANT

These installation instructions are intended for use by

qualified installers. A[[connections for water, electrical power and grounding must comply with local codes and

ordinances and be made by licensed personnel when required. In the absence of a local code:

- Inthe U.S.A., in accordance with the National Electric Code, ANSI/NFPA70 -latest edition/State and

Municipal codes and/or local codes.

- InCanada, in accordance with the Canadian Electric Code C22.1 -latest edition/Provincial and Municipal

codes and/or local codes.

WARNING - This indicates that death or serious inju-

ries may occur as a result of not observing this

warning.

CAUTION - This indicates that minor or moderate inju-

ries or damage may occur as a result of not observing

this warning.

IMPORTANT NOTE/NOTE - This is used to draw the user's attention to something in particular.

Save these instructions for local inspector's use. Observe all governing codes and ordinances.

Note to Installer - Be sure to leave these instructions with

the Consumer.

Note to Consumer- Keep these instructions with your Owner's Manual for future reference.

iiii_i_ii-- _iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_iiiiiiiiiiiiiiiii

Installation options

There are many different installation options. These are limited only by the design of the kitchen and the

function of the finger guard.

Individual unit

Side-by-Side

Individual appliances with partition

]

- When dimensioning the partition for model 4, note the thickness of the furniture fronts to prevent damage ifthe doors are opened at the same time.

- Usethe Extreme Combination Side-by-Side Heating kit

ifthe gap between the appliances is bess

than 6" (160 ram). See the section on "Optionabaccessories" on page 17.

- Minimum thickness of the partition 5/8" (16 ram).

* Partition required!

When 2 appliances are installed Side-by-Side, the Basic

Combination Side-by-Side Sealing kit must be used to ensure a stable connection.

See the section on "Optionab accessories" on page 17.

At the end of the kitchen units

If one side of the appliance isvisible, a side panel must be used.

The side panel must be connected firmly to the wall, the floor

and overhead furniture/fixtures before the appliance is placed in the cavity.

The dimensions of the side panel aretaken from the opposite

cavity wall. During installation ensure that the cavity issquare and the exact size.

_{ii_@_1iiiiiiiYiYiYiYiYijii(_Jiii1i1iimYiiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiii1i_11_iiiiiYiiiiYiiiiYiiiiYiiiiYiiiiiYiiiiiYi1_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_

Installation

Do not install the appliance:

Furniture/fixtures

The new appliance is screwed securely to adjacent and

overhead furniture/fixtures. For this reason it is essential that all attachable furniture/

fixtures are connected securely to the base or the wall by

suitable means.

- outdoors,

- in an environment with dripping water,

- in rooms which are at risk of frost. Appliance is very heavy - for empty weight see the

following table:

Refrigerator 24" Refrigerator 30"

Freezer 18" Freezer 24' Freezer 30"

Wine unit 18" Wine unit 24'

(* without Water Dispenser)

approx. 310 Ibs/140 kg approx. 350 Ibs/158 kg

approx. 255 Ibs/115 kg* approx. 300 Ibs/135 kg*

approx. 335 Ibs/150 kg* approx. 300 Ibs/135 kg

approx. 360 Ibs/160 kg

Installation room

The appliance should be installed in a dry, ventilated room. The ambient temperature should not drop below 55 °F (13 °C)

or rise above 110 °F (43 °C), otherwise malfunctions may

OCCUr,

The installation location should not be exposed to direct

sunlight and not placed near a heat source, such as anoven, radiator, etc. If installation next to a heat source is

unavoidable, use a suitable insulating plate or observe the

following minimum distances from the heat source:

Base

A fully-load appliance is very heavy - for the load-

bearing capacity at least see the following table: Refrigerator 24'

Refrigerator 30" Freezer 18"

Freezer 24' Freezer 30"

Wine unit 18" Wine unit 24' (* without Water Dispenser)

To ensure that the appliance is installed securely and functions properly, the base must be flat and level.

The base must be made of a hard, rigid material. The installation area must be the same height as the rest of

the room.

On account of the heavy weight of a fully loaded appliance, a load-bearing base is required. If indoubt, contact an

architect or a building expert.

approx. 890 Ibs/400 kg approx. 1110 Ibs/500 kg

approx. 560 Ibs/250 kg* approx. 780 Ibs/350 kg*

approx. 950 Ibs/425 kg* approx. 550 Ibs/245 kg

approx. 694 Ibs/310 kg

- 11/4" (30 ram) from an electric cooker,

- 12" (300 ram) from an oil or solid-fuel cooker.

Installation cavity

It is important to observe the specified dimensions of the installation cavity for a trouble-free installation of the

appliance and for the subsequent general view of the

furniture front.

In particular ensure that the cavity is square. Squareness can be checked by suitable means, e.g. spirit

level, diagonal measurements, etc

The minimum thickness of side walls and the top wall must

be 5/s" (16 ram).

The minimum thickness of toe kick panel must be1/2"(13 ram). A thickness of 3/4"(19 ram) is recommended.

Connecting the power

Electrical Shock Hazard

- Plug into a grounded 3 prong outlet.

- Do not remove ground prong.

- Do not use an adapter.

- Do not use an extension cord. Failureto follow these instructions can result indeath,

fire, or electrical shock.

The appliance comes with a 3-wire power supply cord,

UL listed in the USA.

The appliance requires a 3-wire receptacle. The receptacle must be installed by a licensed electrician

only.

The socket must be fused with a 10 to 16 A fuse.

Please observe in this coherence the following table:

Appliance MAX load at one time

Refrigerator 24' 2.0 Ampere Refrigerator 30' 2.0 Ampere Freezer 18" (incl. IceMaker) 3.5 Ampere

Freezer 24' (incl. IceMaker) 4.0 Ampere Freezer 30' (incl. IceMaker) 4.5 Ampere

Wine unit 18' 2.0 Ampere Wine unit 24' 2.0 Ampere

Orient ground prong to the bottom as shown inthe pictures. Forthe installation position of the receptacle see "Installation

dimensions", page 9.

Additional grounding procedure

Some local regulations may require a seperate ground. In such cases, the required accesseory ground wire,

clamp and screw must be purchased seperately. Never ground the appliance to plastic plumbing lines,

gas lines or water pipes.

Grounding instruction

This appliance must be grounded. Inthe event of

a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for

the electric current

Improper connection of the equipment grounding con-

ductor may result in electric shock. Havethe appliance checked by a qualified electrician or service technician

ifyou are indoubt as to whether the appliance has been properly grounded.

Connecting the water

Only connect the appliance to drinking water]

A cold water connection is required for operation of the

automatic ice maker. The water pressure must be between 25 and 120 p.s.i. (1.72-8.25 bar). The installation must

comply with local plumbing regulations.

A separate shut-off valve must be installed for the appliance

water connection.

The shut-off valve for the water connection must not be

behind the appliance. It is recommended to place the shut- off valve directly next to the appliance (base unit) or in another easily accessible location.

When installing the water connection, observe the permitted

installation areas for the pipe. For the permitted installation areas and dimensions see "Installation dimensions", page 9.

The supply pipe can be located at the side on the right (a),

at the side on the left (b) or underneath (c). Maximum outer diameter of the water pipe

(without fittings): 13/32"(10 mm).

Attach a separate shut-off valve for the water connection

in a suitable, easily accessible location. Do not use a self-piercing valve]

Installation dimensions

Single installation

max. 13/32"

(lo)

837/8"

(21:

51/_' 1--

(130) L

315/1_'t

(lOO)

i I!iii!iiiiii Hii i iiii iiiiiiii iiiiii iiiiii iiiiii iiiiii iiiiii iiiiii iiiiii iiiiii iiii ii ii i iiiiii Hi Hii i iiiiii iiiiii iiiiii iiiiii iiiiii iiiiii iiiiii iiiiii iiiiii iiiiii iiiiii iiiiii iiiiii iiiiii iiiiii iiiiii iH

31/3

(25)

133/4''

(350) 1_ "

Legend:

A Area for installation of the water connection.

It isrecommended the water-box be placed adjacent to the installation cavity, so that it can be accessed for service without uninsta[[ing the appliance. Ifthis is not

possible, place the recessed water box adjacent to the power supply socket ebevatedat the heights as

referenced in areas A+B.

x 3

max. o/32

(1o)

it is strongly recommended thletop panel boundary of the niChebe OfSolid material(/8 thickeess). Make suie that

the upper boundary is complete!y flush for a depth Ofat

least 4":

Make sure that the side wails of the niche are completely

flush ! tf, for some reasons; a seperate niche cabinet is

created, make sure that the furniture return area is at least

4!' deep.

Appliance X Y

18" (173/4"/A50,8 mm) 18" (457 mm) 9" (229 mm)

24" (233/4"/603.2 mm) 24" (610 mm) 12" (305 mm) 30" (293/4"/755.6 mm) 30" (762 mm) 15" (381 mm)

B Area for installation of the power connection. C Opening depth of niche, depending on kitchen design.

C = 24" (610 mm) minimum

NOTE: Cavity must be square. Side wall of the cavity must be flush.

Side-by-Side installation

The cavity dimensions indicated above for the respective

appliance apply to a Side-by-Side installation of two appliances.

The total width of the cavity results from the addition of the

cavity widths indicated for the two appliances.

48"

9" ' 15" (762)

(130)

31_1_ '

(100)

18" , (1219) 30"

400

_i iI_

Example: Freezer 18"/Refrigerator 30"

÷ @ @-

18" _!_ 30"

(457) 48" (762)

(1219)

34" 33,6)

18" 30"

(457) 48" (762)

(1219)

Legend:

A Area for installation of the water connection.

It isrecommended the water-box be placed adjacent to the installation cavity, so that it can be accessed for service without uninstalling the appliance. Ifthis is not possible, place the recessed water box adjacent to the power supply socket elevated at the heights as

referenced in areas A+B.

837/8"

(2130)

it is strongly recommended the top panel boundary of the niche be 0f s0tid materia! (!8 thickness). Make sUi÷ that the upper

boundary is completely flush for a depth of at least 4,1 ............

Make sure that the side wails of the niche are completely flus!! if; for Some reasons; a seperate niche cabinet is createct,

make sure that the furniture return area is at least 4!'deep.

B Area for installation of the power connection. C Opening depth of niche, depending on kitchen design.

C = 24" (610 ram) minimum

NOTE: Cavity must be square. Side wall of the cavity must be flush.

Water connection

The supply pipe can be located

a) at the side on the right, b) at the side on the left or

c) underneath,

_ii_I

I i

-ill

_1/32"

(25)

25/_6 .

(59)

max.13/32 .

(1o)

51/8"

(130)

15 "

3 _1"6

(100)

Legend:

A Area for installation of the water connection

B Area for installation of the power connection

(25)

25/_6 ''

(59)

O max. 13/32 "

(lO)

51/8"

(130)

31_[_'i

(100)

(25)

25/_6 .

(59)

max.13/32 .

(1o)

Appliance dimensions

18" Appliance (Freezer/Freezer with Ice and Water dispenser)

1 =l

321/16

141/2"

32 _16

(830 5)

173/4"e 173/£ e), 2315/1_'e)

(450,8) (450,8) (608)

t15/16"

(287,4)

143/16"

(360)

143/16"

(360)

1_43/16"

(360)

115/16"

(287,4)

131/8 ''

(333,7)

b) f) a)e)

797/8 '' 8321/3_'

(2029) (2125_

173/4"e_

_!_6'e)

3/4_' _ .....................................................................

(19)/_ 1725/32"

(451,2)

Legend:

Adjustment in levellinglegs +13/8"(35ram)/-1/2''(13 ram).

Dimensions mayvary.

Thicknessof door panelmay vary.

This dimension may vary depending on installation, panel thickness and kitchen hardware.

(71,7- 106,7)

e) Unitdimensions.

f) Wooden door paneldimension.

Note: One design of the wooden panel displayed.

18" Appliance (Wine unit)

797/_'

(2O

173/4"e)

(450,8)

115/16"

(287,4)

143/16"

(360)

143/16"

(360)

115/16"

(287,4)

131/8''

(333,7)

(608)

b) f) a)e)

797/8 '' 8321/3_'

(2029) (2125)

16"

i _/_) a)

173/4"e) ,

(450,8)

23 '/16

(i 8)

(451,2)

Legend:

Adjustment in levellinglegs +13/8"(35ram)/-1/2''(13 ram).

Dimensions mayvary.

Thicknessof door panelmay vary.

This dimension may vary depending on instabbation, panel thickness and kitchen hardware.

_[2 13/16 --4_16

(71,7 - 106,7)

5/4'

_ o

1i5

e) Unitdimensions.

f) Wooden door paneldimension.

Note: One design of the wooden panel displayed,

24" Appliance (Refrigerator/Freezer/Freezer with Ice and Water dispenser)

233/4" e) 233/4" e) 2315/1_' e) 1/8.b)

(603,2) :_ (603,2) )' _ (608)

115/16"

(287,4)

(830,5)

f)l I

143/16"

(360)

141/2"

(368)

(830,5) i

f)l

2325/32"

(603,6)

e) T

2315/1_'

(6(

2621/32"

(677)

143/16"

(360)

143/16"

(360)

;

115/16"

(287,4)

131/8"

(333,7)

b) f) a)e)

797/8. 8321/3:_'

(2029) (2125)

71/_" .

(18¥)aj

213/1_' - 43/16

(71,7 - 106,7)

115°

[

Legend:

Adjustment in levellinglegs +13/8"(35ram)/-1/2''(13 ram).

Dimensions mayvary.

Thicknessof door panelmay vary.

This dimension may vary depending on installation, panel thickness and kitchen hardware.

9oo

" "(19)

e) Unitdimensions.

f) Wooden door paneldimension.

Note: One design of the wooden panel displayed.

24" Appliance (Wine unit)

797/_'

(2029)

233/4,,e)

(603,2)

115/16"

(287,4)

(360)

/16"

(360)

116116"

(287,4)

131/8"

(333,7)

2315/1_'e)

(608)

b) f)

797/8"

(2029)

a)e)

8321/32'

(2125)

c) 4,

(19) 2325/32"

Legend: a) Adjustment in levellinglegs +13/8"(35 ram)/-1/2'' (13 ram).

b) Dimensions mayvary. c) Thickness of door panelmayvary. d) This dimension mayvary depending on installation,

panel thickness and kitchen hardware.

(603,6)

2621/32"

(671

90°

115 °

e) Unitdimensions.

f) Wooden door paneldimension.

Note: One design of the wooden panel displayed,

30" Appliance (Refrigerator/Freezer/Freezer with Ice and Water dispenser)

e) b)

(755,6)

115/16" (287,4)

143/16"

(360)

2315/!_' 1/8,,

143/16"

(360)

143/16"

(360)

115/16" (287,4)

131/8"

4" (181) a)

(lol,6)

h, 213/16" _43/16

all

b) f) a)e)

797/8 ,,8321/3_'

(2029) (2125)

71/8''

e) (71,7 - 106,7)

293/4"

2925/32"

3/4" (756)

(19) f) 90°

32 21/32"

115 °

(8i'4)

Legend:

Adjustment in levellinglegs +13/8"(35ram)/-1/2''(13 ram).

Dimensions mayvary.

Thicknessof door panelmay vary.

This dimension may vary depending on installation, panel thickness and kitchen hardware.

e) Unitdimensions.

f) Wooden door paneldimension.

Note: One design of the wooden panel displayed,

d_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_iiiiiiiiiiiii_iiii_iii_i_iiii_i_iiii_i_iiii_i_iiii_i_iiii_i_iiiii_iYiiii_iii_I !i_iiiiiiiiiiii¸¸¸¸ ....

Required accessories and tools

Supplied accessories

- Installation instructions

- Operating instructions

- Installation kit

Optional accessories

Basic Combination Side-by-Side Sealing kit For permanent connection of two individual appliances,

e.g. Freezer next to Refrigerator. Extreme Combination Side-by-Side Heating kit

If the gap between the appliances is less than 6' (160 ram). Panel unification part (Metal strip) For connection of two furniture doors. Can be used for

standard height furniture doors without further preliminary work.

Other required accessories from specialist outlets

Ice maker installation kit 1/4" OD copper line For connecting appliances which require water,

e.g. for an ice maker. Maximum outer diameter of the water pipe

(without fittings): 13/32" (10 ram).

- Wooden beam (cross section rain. 3' x A') as an alternative tilt protection, length according to the width

of the installation cavity

- Wooden screws in different sizes

- Thin (max. 1/16"(1.5 mm)), suitable material to protect the floor from damage (e.g. lino)

- Suitable material for covering and protecting furniture (e.g. protective sheets)

- Adhesive tape

Before using, check whether the removed adhesive

tape leaves adhesive residue on the work surfaces!

Otherwise do not use on high-quality work surfaces.

Tools

- Cordless screwdriver T20

- Torx screwdriver T20

- Torx bit T20 + magnetic holder

- 5/16" (8 ram) hex nut driver

- Wood drills in different sizes

- Open end wrench 1/2' (SW 13 ram)

- Multigrip pliers

- Adjustable wrench

- Cutter with adjustable blade

- Metal tape measure

- Square

- Spirit level length 2' (60 cm) and 4' (1,2 m)

- Marking-out level, length at least 4' (1.2 m) for individual appliances or 7' (2.0 m) for Side-by-Side installation

Other

- Stepladder

- Dolly, hand truck

- Hammer drill for drilling holes in wall or floor

- Bits according suitable for material and in different sizes

iiii_iiTii .... ii-ii-ii-ii-ii_

Installation instructions

The following installation instructions describe the installation

steps for various appliance types:

- Refrigerator units

- Freezerunits

- Freezer units with ice maker

- Freezer units with ice-water dispenser

- Wine storage units

Therefore the diagrams may not be a true representation

of your appliance. Particular reference is made to special installation steps

for individual appliance types.

1. Checking the installation cavity

To ensure a safe, trouble-free installation and an optimum overall view of the subsequent furniture front, thoroughly check that the installation cavity complies with the installation requirements.

Before starting the installation,check thatthe installationcavity complies with all requirements for a safe and trouble-free

installation.

• Check the base.

2. Transport of the appliance

The appliance is very heavy.

Be careful, otherwise people who are helping may be injured or the appliance may be damaged.

• Transport the appliance to asuitable installation location with suitable means oftransportation (trolley, lifting truck

or hand-driven truck).

• Secure the appliance during transportation to prevent it from overturning.

The appliance is 8321/32" (2125 mm) tail. If the appliance

cannot be transported in an upright position due to the structural conditions, the appliance can be transported horizontally.

Do not erect the appliance via the side panels. Risk of damage to the appliance!

When erecting the appliance, observe the required minimum

height at the installation location according to the following

table:

Erection via Erection via appliance rear appliance side panel

Follow the instructions in the section on "Installation

location" on page 7.

• Check the dimensions of the cavity.

• Check that the cavity is square.

• Check location of the socket. Also follow the instructions in the section on

"Connecting the power" on page 8 and in the section on "Installation dimensions" on page 9.

• Check location of the water connection (only for appliances with ice maker).

Also follow the instructions in the the section on "Connecting the water" on page 8.

• Check attachment of the adjacent furniture/fixtures. A[[furniture parts inthe vicinity of the appliance must be

connected securely to the wall.

• Check that adjacent furniture/fixtures do not collide (door opening angle).

ii,,,i'i!'!i¸¸

iS[

Minimum height

86"/2185 mm

Always place the means of transport centrally on the

rear side of the appliance. Never push it in from the

front or from the side under the appliance.

Risk of damage to the appliance!

Do not erect the

appliance via the side panels!

- Carefully open the appliance - risk of tipping over- and remove accessories and installation materials

from inside the appliance. Close the door again.

Do not remove transportation safety devices which protect the shelves and storage compartments

inside the appliance until the installation is complete, otherwise the parts may be damaged.

• Check appliance for damage in transit. Do not install the appliance if it isvisibly damaged.

If in doubt, contact your dealer.

• Move the appliance with a hand truck securely.

3. Removing the packaging

The appliance may tip over while it is being unpacked.

- The appliance is very heavy.

- When opening the appliance door, the appliance may tip forwards.

Be careful, otherwise people who are helping may be injured or the appliance may be damaged.

To protect the base from damage dudng installation:

• Attach a residual piece of carpet, [ino, etc. to the floor with adhesive tape in front of the intended installation

location. Remove transportation packaging:

- Remove the cartoon. Use the cutter securely to

protect the surface of appliance.

4. Installation preparation

Unpack installation materials and accessories.

To improve allocation to the work steps, the packages are

identified differently.

To do this, comply with the overview sheet attached to the

appliance!

5. Changing over the door hinges

- Remove packaging material.

- Attach the power cord to the back of the appliance

with a piece of adhesive tape.

- Remove transportation protection devices and lift

appliance off the pallet - appliance isvery heavy!

- Remove accessories from the outside

of the appliance.

Keep adhesive tape which was used to attach

the supplied accessories to the appliance.

It is used subsequently for attaching the edge

protection to the cavity walls (see Section 9.).

Before working on the hinge, release the spring. Risk of injury!

Ifit is not necessary to change over the door hinges,

continue with the next installation step.

- The door hinges cannot be exchanged inthe case of freezers with ice and water dispensers.

Release the spring

• Release the spring on the hinge, Loosen the screw from ItoO.

Exchanging the door hinges

• Remove the hinges.

• Remove the hinge box covers.

• Unscrew the door.

• Remove the ventilation grHbe,

• Mount new the ventilation gribb,

A replacement part for the ventilation grille to adapt to the modified door hinge is included in the installation materials and accessories,

• Change over the hinge angle,

• Change over the fixation parts on the door,

• Fix the hinges on the appliance, Change the hinges crosswise)

• Attach the ventilation grille,

• Fix the door,

Span the spring on the hinge. Tighten the screw from 0to I.

6. Preparing the installation cavity

Assure that there are no electrical wires or plumbing in the area which the screws ooubdpenetrate.

Risk of injury and damage!

- 2 anti-tip-angless are required for each appliance or appliance combination (Side-by-Side).

- The supplied set contains fastening screws for various applications. Select the fastening screws according to the local conditions.

- Ifthe supplied fastening screws do not permit secure attachment of the anti-tip brackets and

therefore the appliance, another method must be

used to attach the anti-tip brackets seoureby.

• Fixthe hinge box cover.

The anti-tip-angles must have a minimum length of 41/8"

(105 mm) over the appliance to ensure a secure stand of the appliance.

If this minimum bencjthcannot be observed for structural conditions it is possible to do this by fastening a spacer behind the anti-tip angle, e. g. a sufficiently dimensioned

wood plank.

The length of the plank should correspond to the width of the

installation niche!

• Specify the attachment points of the anti-tip-angles. Specify the detailed dimensions according to the

section on "Installation dimensions".

• Attach the anti-tip-angles completely. Be sure screws

hold tight.

Fasteningwithwood screws 7.

• Saw the wooden beam (cross section min. 3" x 4')

Attaching an alternative anti-tip

device

Ifthe anti-tip ang[ess cannot be attached securely,

an alternative anti-tip device can be attached.

However, ensure that there is no play between the

appliance and the anti-tip device.

If possible, always screw the wooden beam to existing

studs on the rear panel of the cavity.

to the required length.

Length is equal to the width of the installation cavity!

4x15

: iiiii!_

Fastening with dowels and screws

Always wear safety glasses and other necessary pro- tective devices or apparel when installing or working with anchors.

Risk of injury!

Not recommended for use in light-weight masonry material such as block or brick.

Not recommended for use in new concrete which has not had time to cure.

Do not use core drills to drill holes for this anchor.

If the installation cavity is deeper than the appliance, select a beam which has a larger cross

section or attach 2 beams.

The beam must cover the appliance by

at least 2" (50.8 mm).

(50,8)

(21

÷ 1/32

÷lmm

_N6

5x60 6x31

Mark the installation height (lower edge of the beam) on

the rear panel of the cavity. Select screws according to the thickness of the wooden

beam: length = rain. 2.5 x beam thickness, diameter

#12 or #14.

Specify the number of screws according to the cavity width, thereby ensuring that the beam can

be attached securely.

According to the subsurface:

• Locate wall studs near the rear panel of the cavity and mark drill holes in the beam

• Fasten suitable dowel into the rear wall.

• Predrill the wooden beam.

• Attach the wooden beam to the rear panel of the cavity.

8. Preparing to connect the water

9. Attaching the edge protection

(onty for appliances which require a water connection)

Turn off the main water tap to prevent damage caused

by leaking water.

Attach the connecting pipe to the shut-off valve according to the instructions supplied by the manufacturer of the ice maker installation kit.

Installthe connecting pipe.

Always observe the indicated gap dimensions to prevent damage to the connecting pipe when pushing

in the appliance.

To protect the corners of the installation cavity, attach the

supplied protective brackets with adhesive tape.

10. Side-by-Side installation

If a side-by-side installation is intended, now connect the

two appliances together.

Detailed information on installation can be found in

the separate installation instructions for the sealing kit for side-by-side installation.

>14"

Attach the connecting pipe to the floor with adhesive tape.

The following work steps must be performed on two

interconnected appliances.

11. Pushing the appliance into the installation cavity

Caution when pushing the appliance into the installa- tion cavity. Do not damage the water pipe or power

cord attached to the floor.

When the floor or the appliance is tilted in comparison to the installation cavity adjust height adjustable wheels

before you move the appliance into the instabbation

cavity,

• Put the mains plug into the socket,

In the case of Side-by-Side appliances a separate socket must be used for each appliance.

Prevent the power cord from becoming caught.

Tie a piece of string to the middle of the power cord and feed forwards under the appliance. When pushing inthe appliance, pull the cable forwards.

Using adhesive tape, stick the power cord to the floor centrally behind the appliance approx. 15" (380 ram)

away from the rear panel of the cavity.

• Carefully push the appliance into the cavity.

• Remove edge protection.

12. Installing and aligning the appliance

The installation aid parts on the door have been designed for the following total thickness of furniture doors:

- 3/4" (19 ram)

Never use a cordless screwdriver! Risk of damage to the appliance.

- Do not twist or jam the appliance inside the cavity! When unscrewing the height-adjustable feet, proceed gradually: Always alternate between left and right, left and right, etc..

- The adjustment of the rear feet is facilitated if the appliance is unloaded at the rear.

- Do not bend the appliance against the anti-tip- angles.

- 11/2'' (38 mm) Always take account of the possible differing thickness of the

furniture fronts which are to be fitted subsequently. The height-adjustable feet at the front and rear can all be

adjusted from the front. Front:with open-ended wrench 1/2" (SW13)

Rear:with 5/16" (8 mm) hex nut driver via flexible shaft.

A mark is attached to the appliance base and is used as

a standard gage for height adjustment. When adjusting the height, align this mark at a height of 11/2" (32 ram) above

the floor.

• Align the appliance with the furniture fronts. Place marking-out levelover the installation aid parts on

the door.

1174"

(32 mm)!

Unscrew the height-adjustable feet until the mark on

the base has reached the indicated guide dimension (11/4"/32 ram).

It isvery important to comply with this dimension for

the subsequent alignment of the furniture fronts.

• Align the furniture fronts with the spirit level.

13. Attaching the appliance to the top

of the cavity

Screw the attachment plate lugs (top) to the overhead fumitu re/fixtures.

• Attach the cover strip to the attachment plate (top). Shorten the fitting stdp to the required height!

Inthe case of a side-by-side installation connect both cover rails to the bolt included in the installation

accessories for side-by-side installation

Fixthe attachment plate side lugs (top) depending on

the installation situation.

If there is no gap or only a slight gap, it is not neces- sary to fix the side lugs.

Ifthere is afairly large gap above the appliance,

fit a wooden beam above the appliance, ensuring that the wooden beam fits the gap exactly.

14.

Attaching the individual appliance to the side of the cavity

Screw the attachment plate lugs (side) to the adjacent furniture/fixtures (individual appliances only).

Inthe case of a side-by-side installation this installa-

tion step is not possible. These parts have been

removed.

15. Checking that the finger guard moves easily

It is now essential to check that the finger guard moves easily. At a later time any required corrections will be more difficult.

Note:

The supplied finger guard can be used for both sides of the

door hinge. Because of different installation possibilities, the finger guard

has to be shortened to the required length.

• Shorten the finger guard at the upper side above the

covering strip by 55 mm (1.).

E E

• Push the offcut on the hinge side into the gap between

the appliance and cavity wall. The part has to be easy pushing and pulling (2.)!

16.

Connecting the water to the appliance

When bending the water pipe, do not kink it, otherwise there is a risk of leaks and water damage.

When connecting the water pipe to the solenoid valve of the appliance, follow the instructions supplied by the

manufacturer of the ice maker installation kit enclosed

with the installation manual.

Ensure smooth running at allpositions of the door (3.).

• Remove the cap from the appliance connection (1.).

• Bend the water pipe according to the location of the connection on the appliance (2.).

• Push the union nut and seal onto the water pipe.

• Push the end of the water pipe into the appliance connection and screw on the union nut (3.). Tighten hand-tight.

• Using the open-ended wrench, tighten the union nut.

Do not overturn!

• Open the shut-off valve and main water tap.

• Check the connection on the shut-off valve and on the appliance for leaks.

17. Attaching the toe kick panel

The maximum height of the toe kick panel is4' from the top of the floor.

Do not cover ventilation slots in the base panel. Risk of damage to the appliance.

• If required, cut the toe kick panel to the required length.

• Put on the base panel (do not screw on) and measure the difference in depth Y between the base panel and

toe kick panel of the adjacent furniture.

• Remove the base panel.

• Loosen the brackets for attaching the base panel and

push in all the way.

• Attach the base panel to the appliance.

Remove the protective film from the adhesive pads on the Veloro.

Fitthe toe kick panel to the base panel and press firmly

into place.

• Pull out the brackets by the measured amount Y.

• Screw the brackets tightly.

• Attach the base panel.

19. Preparing the furniture doors

When performing any work on the furniture doors, always observe the following:

- Always screw into the best load-bearing materU of the furniture door.

- Never screw into fillers, decorative strips or similar.

- Select a screw length which is always shorter than the thickness of the furniture front.

- To prevent damage, protect surfaces ofthe furniture doors during installation.

The total weight of the furniture front must not exceed the following values:

- 18" Appliance 44 Ibs/20 kg (19 Ibs/8.5 kg *)

- 24" Applianc 55 Ibs/25 kg (32 Ibs/14.5 kg *)

- 30" Applianc 64 Ibs/29 kg

(* Wine unit)

If required, the toe kick panel can be screwed to the base panel. There are screw holes in the base panel near the Velcro.

18. Commissioning the Appliance

To guarantee the accuracy of the following working steps

and thus the appearance of the overall kitchen front lateron,

the appliance should now be operated.

• Open the appliance door.

• Press the POWER button. Only for appliances with a water connection:

Inorder to avoid the risk of damage caused by leaking water

from damage possibly caused to the water pipe feeding the

appliance, keep the shut-off valve closed.

Adjusting the furniture door The furniture fronts are attached to the app{iance door by

means of fitting parts on the appliance. These fitting parts allow the furniture door to be adjusted precisely and

attached securely to the appliance.

Function of different parts:

1. Double threaded bolt on the adjusting rail: for vertical adjustment of the furniture door.

2. Side brackets: for adjusting the depth of the furniture front.

+ 88 hidden pages