Thermador PRD486JDGU, PRD364JDGU, PRD366JGU Installation

INSTALLATION MANUAL

For THERMADOR PROFESSIONAL PRO GRAND® Dual Fuel Ranges

MANUEL D'INSTALLATION

Pour cuisinières mixtes PROFESSIONAL PRO GRANDmc de THERMADOR

MANUAL DE INSTALACIÓN

Para estufas mixtas PROFESSIONAL PRO GRAND® de THERMADOR

Models/ Modèles / Modelos:

PRD36 PRD48

English Table of Contents

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Important Installation Information . . . . . . . . . . . . . . . . . . . . . 2

Step 1: Ventilation Requirements . . . . . . . . . . . . . . . . . . . . . . . 3

Step 2: Cabinet Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Step 3: Unpacking and Moving the Range . . . . . . . . . . . . . . . . 8

Step 4: Door Removal and Reinstallation . . . . . . . . . . . . . . . . 10

Step 5: Installing Anti-Tip Device . . . . . . . . . . . . . . . . . . . . . . . 12

Step 6: Gas Requirements and Hookup . . . . . . . . . . . . . . . . . 14

Step 7: Electrical Requirements, Connection & Grounding . . . 16

Step 8: Backguard Installation (optional) . . . . . . . . . . . . . . . . . 19

Step 9: Placing and Leveling the Range . . . . . . . . . . . . . . . . . 25

Step 10: Burner Test and Adjustment . . . . . . . . . . . . . . . . . . . 29

Installer Final Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

To Clean and Protect Exterior Surfaces . . . . . . . . . . . . . . . 30

This THERMADOR® appliance is made by

BSH Home Appliances Corporation

5551 McFadden Ave.

Huntington Beach, CA 92649

Questions?

1-800-735-4328

www.thermador.com

We look forward to hearing from you!

Safety Instructions

Important Safety Instructions

READ AND SAVE THESE INSTRUCTIONS

APPROVED FOR ALL RESIDENTIAL APPLIANCES

FOR RESIDENTIAL USE ONLY

IMPORTANT: Save these Instructions for the Local Gas Inspector’s use.

INSTALLER: Please leave these Installation Instructions with this unit for the owner.

OWNER: Please retain these instructions for future reference.

WARNING:

Disconnect power before installing. Before turning power ON, be sure that all controls are in the OFF position.

Important:

Local codes vary. Installer is responsible for ensuring that the installation, gas connections, and grounding comply with all applicable codes. Failure to follow codal procedures

may void the warranty.

WARNING:

Tip Over Hazard!

A child or adult can tip the range over and be killed.Verify that the anti-tip bracket is securely installed. Ensure the anti-tip bracket is engaged when the range is moved. Do not operate the range without the anti-tip bracket in place. Failure to follow the instructions in this manual can result in death or serious burns to children and adults. Check for proper installation and use of anti-tip bracket. Carefully tip range forward pulling from the back to ensure that the anti-tip bracket engages the cast aluminum base and prevents tipover. Range should not move more than 1 inch (2.5cm).

WARNING:

If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

— Installation and service must be performed by a

qualified installer, service agency or the gas supplier.

For Massachusetts Installations:

1. Installation must be performed by a qualified or licensed contractor, plumber or gas fitter qualified or licensed by the state, province or region where this appliance is being installed.

2. Shut-off valve must be a “T” handle gas cock.

3. Flexible gas connector must not be longer than 36” (914mm).

Note: This Range is NOT designed for installation in manufactured (mobile) homes or Recreational Park Trailers.

DO NOT install this range outdoors.

English 1

Important Installation Information

GAS Type Verification

Verify that the appliance is correct for the type of gas provided at installation location. Ensure that the appliance is connected to the type of gas for which it is certified. Before proceeding with the installation refer to “Step 6: Gas Requirements and Hookup” on page 14

All models are certified for use with natural gas. Field conversion of the appliance for use with propane gas supply will require installation of conversion kit supplied with the range (service number 553182). Only a qualified service technician or installer should make this conversion. See LP Conversion Kit instructions for full installation information.

WARNING:

To avoid possible burn or fire hazard, a backguard designed specifically for this range must be installed whenever the range is used.

Refer to “Backguard Kit Model Numbers” on page 24, for the correct backguard models that are designed for this range. After selecting the correct backguard, the range must be installed properly, using the minimum clearances to combustible surfaces specified in “Step 2: Cabinet Preparation” on page 4.

Important:

For island installations and other installations with more than 12” (305mm) minimum horizontal clearance between combustible materials and the back edge of the range, a Flush Island Trim has been supplied with the range (refer to “Figure 2: Side View Of Clearances” on page 6). A

THERMADOR® Low Back or High Shelf must be purchased separately and utilized when there is less than a 12” (305mm) horizontal clearance.

Check local building codes for the proper method of appliance installation. Installation, electrical connections and grounding must comply with all applicable codes. Local codes vary and it is the responsibility of the installer to ensure installation is in accordance with these codes. In the absence of local codes the appliance should be installed in accordance with the National Fuel Gas Code ANSI Z223.1/ NFPA 54 current issue and National Electrical Code ANSI/ NFPA 70-current issue. In Canada, installation must be in accordance with the CAN 1-B149.1 and.2 – Installation Codes for Gas Burning Appliances and/or local codes.

This appliance complies with one or more of the following standards:

• UL 858, Standard for the Safety of Household Electric Ranges

• UL 923, Standard for the Safety of Microwave Cooking Appliances

• UL 507, Standard for the Safety of Electric Fans

• ANSI Z21.1, American National Standard for Household Cooking Gas Appliances

• CAN/CSA-C22.2 No. 113-10 Fans and Ventilators

• CAN/CSA-C22.2 No. 61-08 Household Cooking Ranges

It is the responsibility of the owner and the installer to determine if additional requirements and/or standards apply to specific installations.

It is strongly recommended that this appliance be installed in conjunction with a suitable overhead vent hood (see “Step 1: Ventilation Requirements” on page 3). Due to the high heat capability of this unit, particular attention should be paid to the hood and duct work installation to assure it meets local building codes.

Gas Supply:

Natural Gas – 6” water column (14.9 mb) min., 14” (34.9 mb) maximum Propane Gas – 11” water column (27.4 mb) min., 14” (34.9 mb) maximum

Electric Power Supply:

See “Step 7: Electrical Requirements, Connection & Grounding” on page 16 for specifications.

This appliance has been tested in accordance with ANSI Z21.1, Standard for Household Cooking Appliances (USA) and in accordance with CAN 1.1-M81 Domestic Gas Ranges (Canadian).

English 2

CAUTIONS:

• To eliminate risk of burns or fire caused by reaching over heated units, cabinet storage above the surface units should be avoided.

• When connecting the unit to propane gas, make certain the propane gas tank is equipped with its own high-pressure regulator in addition to the pressure regulator supplied with the range. The maximum gas pressure to this appliance must not exceed 14.0 inches water column (34.9 mb) from the propane gas tank to the pressure regulator.

• This unit is designed as a cooking appliance. Based on safety considerations, never use it for warming or heating a room.

Tools Needed

(2) 1/2” wrenches 1/8” (3.17mm) drill bit

3/16” (4.76mm) drill bit 12” Adjustable wrench

Hand or electric drill Tape measure

Phillips & flathead screwdrivers Marking instrument

Level Furniture dolly

T-20 Torx screwdriver Protective gloves

Items Not Included

Drywall/Concrete Anchors Pipe Compound/Tape

Rope/Twine 3/4” (19mm) Flex Line

Strain Relief

Step 1: Ventilation Requirements

It is strongly recommended that a suitable exhaust hood be installed above the range. Downdraft ventilation should not be used. The table below indicates the ventilation hood options and blower capacity guidelines that are

recommended for use with all THERMADOR® ranges.

NOTICE:

Most range hoods contain combustible components which must be considered when planning the installation.

Do not install a microwave oven/ventilator combination above the range, as these type of units do not provide the proper ventilation and are not suitable for use with the range.

1. Select Hood and Blower Models:

• For wall installations, the hood width must, at a minimum, equal the width of the range. Where space permits, a hood larger in width than the range may be desirable for improved ventilation performance.

• For island installations, the hood width should, at a minimum, overhang the range by a minimum of 3" (76mm) on each side.

2. Hood Placement:

• For best smoke elimination, the lower edge of the hood should be installed 30" (762mm) above the range cooking surface (see “Figure 1: Cabinet Clearances” on page 5).

• If the hood contains any combustible materials (i.e. a wood covering), it must be a minimum of 36" (914mm) above the cooking surface.

3. Consider Make-Up Air:

• Due to the high volume of ventilation air, a source of outside replacement air is recommended. This is particularly important for tightly sealed and insulated homes. A qualified heating and ventilating contractor should be consulted.

Important:

Ventilation hoods and blowers are designed for use with single wall ducting. However, some local building codes or inspectors may require double wall ducting. Consult local building codes and/or local agencies, before starting, to assure that hood and duct installation will meet local requirements.

Range

Width

36”

48” 6 burners with griddle 1200 (cfm)

Important Notes: It is recommended that a THERMADOR PROFESSIONAL

PROFESSIONAL

Blowers, and Accessories.

* For high output gas ranges (60,000 BTU or greater), the minimum of one (1) CFM of ventilation per 100 BTU is recommended. If the range has a griddle, add 200 CFM to the estimated blower capacity. Additional blower capacity may be required for longer duct runs.

For island applications, it is recommended to use a hood width that exceeds the width of the range by 6” (152mm), overlapping the range by a minimum of 3” (76mm) on each end.

CFM = “cubic feet per minute” (standard blower capacity rating).

Ranges. Refer to www.thermador.com for a complete selection of Professional Ventilation options,

Range Top

Configuration

4 burners with griddle

6 burners 1100 (cfm)

Cubic Feet per Minute

(min requirement)

800 (cfm) 36” or 42” Pro Wall Hood

wall or island hood or custom insert is used with THERMADOR

Ventilation Options

36” Custom Insert w/ optional blower

42” or 48” Island Hood w/ optional blower

48” or 54” Pro Wall Hood

48” Custom Insert w/ optional blower

English 3

Step 2: Cabinet Preparation

• The range is a free standing unit. If the unit is to be placed adjacent to cabinets, the clearances shown in “Figure 1: Cabinet Clearances” on page 5 are required. The same clearances apply to island installations, except for the overhead cabinets, which must have a space wide enough to accept the flared island hood, as also indicated in Figure on page 5.

• The gas and electrical supply should be within the zones shown in Figure 3 on page 7.

• Any openings in the wall behind the range and in the floor under the range must be sealed.

• When there is less than a 12" (305mm) horizontal

clearance between combustible material and the

back edge of the range above the cooking surface, a

THERMADOR® Low Back or High Shelf must be installed (see Figure 2, page 6). When clearance to

combustible material is over 12" (305mm), the

supplied THERMADOR® Flush Island Trim may be used. Figure 2 indicates the space required for each type of backguard.

• A 5” (127mm) minimum clearance is needed when the range is installed beside a combustible side wall.

• Always keep appliance area clear from combustible materials, gasoline and other flammable vapors and liquids.

• Do not obstruct the flow of combustion and ventilation air to the unit.



As defined in the “National Fuel Gas Code” (ANSI

Z223.1, Current Edition).

CAUTION:

Do not install the range such that the oven door is flush with the cabinet face. A flush installation could result in damage to the cabinets due to exposure to high heat.

Note: The maximum depth of overhead cabinets installed on either side of the hood is 13" (330mm).

There is a 36” (914mm) minimum clearance required between the top of the cooking surface and the bottom of an unprotected cabinet. A 30” (762mm) clearance can be used when the bottom of the wood or metal cabinet is protected by not less than 1/4” (6mm) of a flame retardant material covered with not less than No. 28 MSG sheet steel, 0.015” (0.38 mm) thick stainless steel, 0.024” (0.61 mm) aluminum, or 0.02” (0.51 mm) thick copper.

Flame retardant materials bear the mark:

UNDERWRITERS LABORATORIES INC. CLASSIFIED MINERAL AND FIBER BOARDS SURFACE BURNING CHARACTERISTICS

followed by the flame spread and smoke ratings. These designations are shown as “FHC (FIame Spread/Smoke Developed).” Materials with “O” flame spread ratings are flame retardant. Local codes may allow other flame spread ratings. It is the responsibility of the installer to ensure installation is in accordance with these ratings.

English 4

18” (457mm)

minimum

For 36” Ranges {36” (914mm) or 42” (1067mm) Wide Hood {42” (1067mm) or 48” (1219mm) for Island

For 48” Ranges {48” (1219mm) 54” (1372mm), or 60” (1524mm) Wide Hood {54” (1372mm) for Island

30” (762mm) min. from bottom of Overhead Hood to cooking surface. 36” (914mm) min. If hood contains combustible materials.

36” Range - 36” (914mm)

48” Range - 48” (1219mm) Min. distance between overhead cabinets of combustible material

13” (330mm)

Max Cabinet

Depth

Range width

36” (914mm) or 48” (1219mm)

5” (127mm) min. to combustible

sidewall

material (both sides).

CAUTION!

See Figure 2 36” (914mm) Min.

to combustible material from cooking Surface

/8” (911mm) Min. range height

*35 with leveling legs fully retracted.

*363/4” (933mm) Max range height

with leveling legs fully extended.

For Electrical & Gas Supply zones, see Figure 3. Zone sizes & positions differ according to model.

Gas Zone

as defined in the “National Fuel Gas Code” ANSI Z223.1,

Current Edition). *The range height is adjustable. The level of the range top must be at the same level or above the countertop level.

Electrical Zone

FIGURE 1: CABINET CLEARANCES

English 5

36” (914mm) Min to combustible materials

36 3/4” Max (933mm)

/8” Min (911mm)

Installation with Low Back or High Shelf

” (797mm)

” (737mm)

High Shelf

minimum

recess depth

3” (76mm)

12” (306mm)

Low Back

Guard

” (638mm)

Combustible Materials

22” (559mm)

12”

(305mm)

Installation with Included Flush Island Trim

36” (914mm) min

to combustible

materials

36 3/4” Max (933mm)

/8” Min (911mm)

/2” (723

483/4” (1238mm)

12” (305mm) Min to Combustible with Flush Island Trim

Flush Island Trim

mm)

Combustible Materials

Note: For Flush Island Trim installations, counter surface should have a cantilever edge meeting the back section

of the Flush Island Trim

accessory.

Cantilever

Note: If an inner wall is used under the cantilever counter top, there should be a 1/8” (3mm) gap from the rear of the range to the inner wall.



As defined in the

“National Fuel Gas Code” (ANSI Z223.1, Current Edition).

English 6

FIGURE 2: SIDE VIEW OF CLEARANCES

Gas and Electric Supply Zone

Model A B C D

36” (913mm)

48” (1219mm)

10” (254mm)

91/8” (232mm) 73/8” (187mm) 73/8” (187mm) 91/8” (232mm)

/8” (587mm)

7” (178mm) 7” (587mm)

3” (76mm)

36” (913mm)

48” (1219mm)

77/8” (200mm)

2” (51mm)

Notice:

• If not already present, install gas shut-off valve in an easily accessible location.

• Make sure all users know where and how to shut off the gas supply to the range.

• Any opening in the wall behind the appliance and any opening in the floor under the appliance must be sealed.

The dual fuel ranges may be connected to the power supply with a range supply cord kit or by hard-wiring to the power supply. It is the responsibility of the installer to provide the proper wiring components (cord or conduit and wires) and complete the electrical connection as dictated by local codes and ordinances, and/or the National Electric Code. The units must be properly grounded. Refer to “Step 7: Electrical Requirements, Connection & Grounding” on page 16 for details.

Figure 3: Gas & Electrical Supply Locations

The range must be connected only to the type of gas for which it is certified. If the range is to be connected to propane gas, ensure that the propane gas supply tank is equipped with its own high pressure regulator in addition to the pressure regulator supplied with the range (see “Step 6: Gas Requirements and Hookup” on page 14).

Note: The range is designed for nearly-flush installation to the back wall. For a successful installation, it may be necessary to reposition the gas supply line and electrical cord as the range is pushed back to its final position. It is suggested that this may be accomplished by carefully pulling on a rope or twine looped around the gas or electrical supply line which is pulled from beneath the range and out the front as the range is pushed back into its final position.

English 7

Electrical Supply

Installation of the range must be planned so that the roughin of the terminal block for the receptacle or conduit connection will allow maximum clearance to the rear of the unit.

When the power supply cord or conduit is connected to the mating receptacle or terminal block cover, the combined connection should protrude no more than 2“(51mm) from the rear wall (see Figure 4).

Refer to Figure 11 on page 16 for location of the terminal block on unit. To minimize binding when the unit is connected, orient the receptacle or conduit connector, and slide back into position.

2” (51mm) maximum

2” (51mm) maximum when plugged in

Step 3: Unpacking and Moving the Range

CAUTION:

The unit is heavy and should be handled accordingly. Proper safety equipment such as gloves and adequate manpower of at least two people must be used in moving the range to avoid injury and to avoid damage to the unit or the floor. Rings, watches, and any other loose items that may damage the unit or otherwise might become entangled with the unit should be removed.

Hidden surfaces may have sharp edges. Use caution when reaching behind or under appliance.

The range has an approximate shipping weight as shown in “Chart A”. The grates, griddle plate, burner caps, and oven racks must be removed to facilitate handling. Do not remove the griddle element and tray assembly.

1. Remove the outer carton and packing materials from the shipping pallet but leave the adhesive-backed foam layer over brushed-metal surfaces, to protect finish from scratches, until the range is installed in its final position.

2. Remove the door(s) (see “Step 4: Door Removal and Reinstallation” on page 10); however, do not remove the warming drawer or steam oven doors. This will create an estimated reduction in the weight as shown in “Chart A” and allow the range to pass through 30" (762mm) doorways (see clearances shown on page 6).

English 8

Figure 4: Wall Connection

Chart A

Shipping Weight 420 lbs

Weight without packing materials

Without door(s), burner caps, and oven racks

36"

Range

(191 kg)

360 lbs

(163 kg)

260 lbs

(118 kg)

Caution

DO NOT lift the range by the oven door's handle, as this may damage the door hinges and cause the door to fit incorrectly.

48"

Range

590 lbs

(268 kg)

530 lbs

(240 kg)

390 lbs

(177 kg)

Remove all tape and packaging before using the appliance. Please, recycle the packaging

material, as all THERMADOR® appliance packaging material is recyclable. Never allow children to play with packaging material.

3. All ranges are held to the pallet by (4) bolts through a wood block center (see Figure 5). The two front pallet bolts are accessible only after removing the Door Trim located beneath the doors.

• The Door Trim is removed by loosening the 2

screws attaching it to the range and sliding it up and off the screws.

• Due to the weight, a furniture dolly with soft wheels or an air lift should be used to move this unit. The weight must be supported uniformly across the bottom (see Figure 6).

• After transporting the range by dolly close to its final location, the range can be tipped back and supported on the rear casters while the dolly is carefully removed.

• “Step 5: Installing Anti-Tip Device”, “Step 6: Gas Requirements and Hookup”, “Step 7: Electrical Requirements, Connection & Grounding”, and “Step 8: Backguard Installation (optional)” must be completed before the range is placed in its final position.

• Use the casters to assist with the installation near to its final location. THE FLOOR UNDER THE LEGS

SHOULD BE PROTECTED BEFORE PUSHING THE UNIT INTO POSITION.

Loosen Screws

Wood Packing Blocks

Pallet Bolts

Figure 5: Door Trim, Packing Blocks, & Pallet Bolts

4. After removing the pallet bolts using (2) 1/2” (13mm) wrenches (one to hold bolt at the bottom while the other is loosening the nut at the top) and discarding the wood packing block inserts, the range may be carefully tilted back on the (2) casters (see Figure 24 on

page 25) and removed from the pallet. Use additional help as required to remove from pallet.

Range must be uniformly

supported by

braces

provided on

bottom of

range.

” (578mm)

Figure 6: Furniture Dolly Positioning

English 9

Step 4: Door Removal and Reinstallation

CAUTION:

USE CAUTION WHEN REMOVING THE DOOR. THE DOOR IS VERY HEAVY.

• Make sure oven is cool and power to the oven has been turned off before removing the door. Failure to do so could result in electrical shock or burns.

• The oven door is heavy and fragile. Use both hands to remove or replace the door.

• Failure to grasp the oven door firmly and properly could result in personal injury and product damage.

• With the door off, never release the levers and try to close the hinges. Without the weight of the door, the powerful springs will snap the hinges closed with great force.

To Remove the Oven Door:

1. Open the door fully and use a screwdriver to carefully pry the hinge clips away from the hinge slots (Photo A).

2. Flip the hinge clip toward you (Photo B).

3. Close the door until it stops against the hinge clips. The open hinge clips will hold the door open at a slight angle.

4. Grasp the door firmly on the ends of the door handle, and lift the door up. (There will be some spring resistance to overcome.) When the door is lifted sufficient to clear the hinge hooks, the door can be pulled straight out (Photo C). Place the door in a safe and stable location.

Photo A

Photo B

English 10

Photo C

To Reinstall the Oven Door:

To Check Door Fit and Operation:

1. Position the door at a sharp angle (see Figure 7) and insert the hinges centered evenly into the hinge slots. The hinges will securely hook into the slots when properly installed. Do not force, bend, or twist the door.

• Tip: Rest the door on your foot while using your leg

for stability.

2. Open the door fully and use a screwdriver to push the hinge clips all the way into the hinge slots (toward the oven) until they meet the hinge. Be careful not to scratch the range during this process.

23°

1. Open and close the door slowly to test the movement and the fit of the door to the oven cavity. Do not force the door to open or close. If the door is properly installed, it should move smoothly and rest straight on the front of the range when closed.

2. If the door does not operate correctly, verify that the hinges are properly seated into the hinge slots, and that the hinge clips are fully engaged into the slots.

3. For large and small ovens, if door or handle appears slightly tilted, you may adjust the hinge receiver by rotating the large Torx-head screw located directly above the hinge receiver with a T-20 Torx driver. Rotate each screw respective to its side and direction the door needs to be adjusted (Photo D).

• The warming drawer and steam oven doors are not

adjustable.

Turn this

screw to adjust door alignment

Figure 7: Approximate Door Angle for Removal

Photo D

English 11

Step 5: Installing Anti-Tip Device

WARNING — RANGE TIPPING HAZARD:

• To prevent accidental tipping of the range, attach it to the floor by installing the Anti-Tip Device supplied.

• A risk of tip-over may exist and injury can result if the appliance is not installed in accordance with these instructions. For all ranges an anti-tip device must be

installed as per these instructions.

• If the range is pulled away from the wall for cleaning, service or for any other reason, ensure that the AntiTip Device is properly re-engaged when the range is pushed back against the wall. In the event of abnormal usage (such as a person standing, sitting, or leaning on an open door), failure to take this precaution can result in tipping of the range. Personal injury might result from spilled hot liquids or from the range itself.

WARNING — ELECRICAL SHOCK HAZARD:

• Use extreme caution when drilling holes into the wall or floor as there may be concealed electrical wires.

• Identify the electrical circuits that could be affected by the installation of the Anti-Tip Device, then turn off power to these circuits.

• Failure to follow these instructions may result in electrical shock or other personal injury.

Tools Needed for Installation of Anti-Tip Device:

• Screwdriver, Phillips

• Drill, electric or hand

• Measuring tape or ruler

• 1/8” (3.17mm) drill bit (wood or metal; wall or floor)

• 3/16” (4.76mm) carbide-tipped masonry drill bit (concrete or concrete block wall or floor)

• 3/16” (4.76mm) anchors, drywall or concrete, 4 each (not required if mounting bracket is being attached to solid wood or metal)

• Hammer

• Pencil or other marker

WARNING

--A child or adult can tip the range and be killed.

--Verify the anti-tip device has been properly installed and engaged as per installation instructions.

--Ensure the anti-tip device is reengaged when the range is moved.

--Do not operate the range without the anti-tip device in place and engaged.

--Failure to do so can result in death or serious burns to children or adults.

--See further Installation Instructions.

ATTENTION — PROPERTY DAMAGE:

• Contact a qualified installer or contractor to determine the proper method for drilling holes through the wall or floor material (such as ceramic tile, hardwood, etc.)

• Do not slide the range across an unprotected floor.

• Failure to follow these instructions may result in damage to wall or floor coverings.

English 12

THERMADOR

Service Part No.

415078 4

655355 1 Anti-Tip Bracket

Qty Description

Screw, Phillips, #10 x 1

(38.1mm)

”

Important Installation Information:

• Attach anti-tip bracket to a solid wood cabinet having a

minimum wall thickness of 3/4” (19mm). The thickness of the wall or floor may require use of longer screws, available at your local hardware store.

• Use appropriate anchors when fastening the mounting

bracket to any material other than hard-wood or metal.

• In all cases, at least (2) of the bracket mounting screws

must firmly fasten the anti-tip bracket to the floor, and (2) of the mounting screws (or drywall anchors) must firmly fasten the anti-tip bracket to the rear wall (see Figure 8 and Figure 9).

3”

(76mm)

• For walls or floors composed of concrete or concrete block, drill 3/16” (4.76mm) holes to a minimum depth

of 1

” (44mm), then tap concrete anchors into each

of the holes using a hammer.

• For walls or floors having ceramic tile covering, drill 3/16” (4.76mm) holes through the tile only, then drill into the material behind the tile as indicated immediately above.

• Place bracket on floor near the center of where the unit is to be finally located (shown in Figure 8).

• If the range is moved to a new location, the Anti-Tip Device must be reinstalled.

2. Secure bracket into the wall stud and to the floor using the screws provided.

3. Later, when the unit is installed, the adjustable legs will allow the cast base to slide under the bracket hook, stabilizing the unit.

Figure 8: Anti-tip Bracket Mounting Location

Mounting the Anti-Tip Bracket

1. Prepare holes at fastener locations as identified below:

• For walls, wall studs, or floors composed of solid wood or metal, drill 1/8” (3.17mm) pilot holes.

• For walls or floors composed of drywall, sheet-rock or other soft materials, drill 3/16” (4.76mm) holes to a

minimum depth of 1

” (44mm), then tap plastic

anchors into each of the holes using a hammer.

Figure 9: Anti-tip Bracket

English 13

Step 6: Gas Requirements and Hookup

Verify the type of gas being used at the installation site. Make certain the range matches the type of gas available at this location. The appliance is shipped from the factory for use with natural gas. It must be converted for use with propane.

Field conversion of the appliance for use with propane gas supply will require installation of the conversion kit supplied with the range (service number 553182). A qualified technician or installer must do the conversion. See LP Conversion Kit instructions for full installation information. Obey all instructions in this kit for correct conversion of the gas regulator and settings for the gas valves.

CAUTION:

When connecting unit to propane gas, make certain the propane gas tank is equipped with its own high pressure regulator in addition to the pressure regulator supplied with the appliance. The pressure of the gas supplied to the appliance regulator must not exceed 14" water column (34.9 mb).

NATURAL GAS REQUIREMENTS:

WARNING:

If a gas conversion kit is used, the kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in the instructions is not followed exactly, a fire, explosion, or production of carbon monoxide may result causing property damage, personal injury, or loss of life. The qualified service agency is responsible for the proper installation of the kit. The installation is not proper and complete until the operation of the converted appliance is checked as specified in the manufacturer’s instructions supplied with the kit.

Hook Up

The gas supply connections shall be made by a competent technician and in accordance with local codes or ordinances. In the absence of local codes, the installation must conform to the National Fuel Gas Code ANSI Z223.1/ NFPA54- current issue.

Inlet Connection: 3/4” (19mm) NPT external

1/2” (12.7mm) NPT internal

(Minimum 3/4” dia. flex line.)

Supply Pressure: 6" min. to 14" max. water

column.

(14.9 to 34.9 mb)

Manifold Pressure: 5" water column (12.5 mb)

PROPANE GAS REQUIREMENTS:

Inlet Connection: 3/4” (19mm) NPT external

1/2” (12.7mm) NPT internal

(Minimum 3/4” dia. flex line.)

Supply Pressure: 11" min. to 14" max. water

column. (27.4 mb to 34.9 mb)

Manifold Pressure: 10" water column (24.9 mb)

WARNING:

Do not remove the back cover of the range. It is for an authorized servicer access only.

Gas Line Connection

Figure 10: Manifold Gas Line Connection

English 14

A manual gas shut-off valve must be installed external to the appliance, in a location accessible from the front, for the purpose of shutting off the gas supply. The supply line must not interfere with the back of the unit.

The range is supplied with its own pressure regulator that has been permanently mounted inside the range.

• Make sure the gas supply is turned off at the manual shut-off valve before connecting the appliance.

• Use 3/4” (19mm) flex line to connect between the gas supply and the appliance inlet pipe, which exits the rear, lower right of the appliance. The appliance pipe connection has a 3/4” (19mm) NPT external thread and a 1/2” (13mm) NPT internal thread (see Figure 10 on page 14).

• Use caution to avoid crimping the 3/4” (19mm) flex

line when making bends.

• Suggested length of the flex line is 48” (1219mm);

however, check local codes for requirements before installation.

• Use pipe sealing compound or Teflon® tape on the pipe threads, and be careful not to apply excessive force when tightening the fittings.

Leak testing of the appliance shall be in accordance with

the following instructions.

• Turn on gas and check supply line connections for leaks using a soap and water solution.

• Bubbles forming indicate a gas leak. Repair all leaks immediately after finding them.

WARNING:

Do not use a flame of any kind to check for gas leaks.

Installer is responsible for ensuring that the installation, gas connections, and grounding comply with all applicable codes.

CAUTION:

The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5kPa.).

The appliance and its individual shut off valve must be disconnected from the gas supply piping system during any pressure testing of the system at test pressures in excess of 1/2 psig (3.5kPa.).

When checking the manifold gas pressure, the inlet pressure to the regulator should be at least 6.0" W.C. (14.9 mb) for natural gas or 11.0" W.C. (27.4 mb) for propane.

Do not attempt any adjustment of the pressure regulator.

English 15

Step 7: Electrical Requirements, Connection & Grounding

• Prior to servicing appliance, always disconnect appliance electrical supply cord, if so equipped, from wall receptacle. If appliance is hard-wired to power supply, disconnect power to unit by turning off the proper circuit breaker or disconnecting the proper fuse. Lock service panel to prevent power from being turned ON accidentally.

Dual Fuel range models can be connected or hardwired to the power supply as described on page 17.

Chart B: Electrical Supply Circuit Requirements

MODEL

TYPE

36” 240/208 VAC 40 Amps 60 Hz. Single

48" 240/208 VAC 50 Amps 60 Hz. Single

• A neutral supply wire must be provided from the power source (breaker/fuse panel) because critical range components, including the surface burner spark reignition module, require 120 VAC to operate safely and properly.

VOLTAGE

WARNING:

An improper 120/ 240 VAC power supply will cause malfunction, damage to this appliance, and possibly create a condition of shock hazard.

• If the correct power supply circuit is not provided, it is the responsibility and obligation of the installer and user to have proper power supply connected. This must be accomplished in accordance with all applicable local codes and ordinances by a qualified electrician. It is the responsibility of the installer to ensure compliance of local codes. In the absence of local codes and ordinances, the power supply connection shall be in accordance with the National Electric Code.

• Observe all governing codes and ordinances when grounding. In the absence of these codes or ordinances observe National Electrical Code ANSI/ NFPA No. 70 current issue. See the following information in this section (Step 7) for grounding method.

• Electrical wiring diagrams and schematics are attached behind the Door Trim of the range, for access by a qualified service technician (see Figure 5 page 9).

• The ranges are to be connected to a 240/208 VAC power supply.

CIRCUIT

RATING

Dual Fuel models must be connected to the power supply utilizing one of the following methods. For all methods of connection, the length of the cord or conduit/wiring must allow the unit to be slid completely out of the cabinet without having to unplug or disconnect the unit from the power supply. Recommended minimum free length of cord or conduit is 4ft (1.2m). Electrical installations and grounding must be in accordance with all local codes and ordinances, and/or the National Electric Code, as applicable.

Range: Left Side

Terminal Block

FREQUENCY PHASE

Location

English 16

Figure 11: Terminal Block Location

Figure 12: Terminal Block

PERMANENT CONNECTION (HARD WIRING) — Units may be hard wired to the power supply. The installer must provide approved flexible aluminum conduit, 3/4” (19mm) trade size, maximum 6ft (1.8m) long. Locate the terminal block on the rear of the unit and remove cover (refer to Figure 11). The conduit must be installed to the terminal block using an approved conduit connector. The free end of the conduit must be connected to a junction box provided in the electrical supply zone, as shown in Figure 3 on page 7.

Mount a strain relief (not provided) into the 1" (25.4mm) diameter hole located below the terminal block (see Figure 13). Wiring for the unit is to be brought into the terminal block through the conduit and through the strain relief. The ends of the wiring must have 1/4” faston closedloop lugs attached, preferably soldered in place. Make the connections to the terminal block provided (see Figure 12).

If aluminum supply wiring exists in the installation, splice the aluminum house wiring with appropriate-thickness gauge copper wire for adapting to the range, using special connectors designed and certified for joining copper and aluminum wire. Follow the connector manufacturer’s

recommended installation procedure.

WARNING:

Improper connection of aluminum house wiring can result in a fire or shock hazard. Use only connectors designed and certified for connecting to aluminum wire.

Installer — show the owner the location of the circuit breaker or fuse. Mark it for easy reference.

Terminal Block

Relief

Strain

Figure 13: Strain Relief Location

4-CONDUCTOR CORD— NORMALLY, A UNIT MUST BE CONNECTED TO THE POWER SUPPLY WITH A 3POLE, 4-CONDUCTOR CORD KIT RATED 125/250 VOLTS, 50 AMPERES, AND MARKED FOR USE WITH RANGES.

The cord kit must be attached to the range terminal block with a strain relief which will fit a 1" (25.4mm) diameter hole. If not already equipped, the cord must also have 1/4” (6mm) faston closed-loop lugs attached to the free ends of the individual conductors, preferably soldered in place.

4-Wire Connection

1. Remove upper nuts only from the terminal block studs. Do not remove lower nuts which secure range internal wiring leads.

2. Mount strain relief (not provided with range) into the 1" (25.4mm) diameter hole in the back panel located below the terminal block (see Figure 13 and Figure 12). Route wires up through strain relief.

3. Secure the neutral, grounded wire of the supply circuit, to the center stud of the terminal block with nut (see Figure 14).

4. Secure the L1 (black) and L2 (red) power leads to the outside terminal studs (brass colored) with nuts.

5. Remove green ground screw located beneath the terminal block. Discard white wire.

6. Secure the bare copper ground lead to the range chassis using the ground screw previously used for the white wire. Be sure that neutral and ground terminals do not touch.

English 17

7. Tighten all connections securely.

Figure 14: 4-Wire Connection

8. Reinstall the Terminal Block Cover.

3-CONDUCTOR CORD — WHERE LOCAL CODES AND ORDINANCES PERMIT GROUNDING THROUGH NEUTRAL, AND CONVERSION OF SUPPLY TO 4 WIRE IS IMPRACTICAL, UNIT MAY BE CONNECTED TO THE POWER SUPPLY WITH A 3-POLE, 3-CONDUCTOR CORD KIT RATED 125/250 VOLTS, 50 AMPERES, AND MARKED FOR USE WITH RANGES.

3-Wire Lead Connection

1. Remove upper nuts only from the terminal block studs. Do not remove nuts which secure range internal wiring leads.

2. Mount strain relief (not provided with range) into the 1" (25.4mm) diameter hole in the back panel located below the terminal block (see Figure 13 and Figure 12). Route wires up through strain relief.

3. Secure the neutral, grounded wire of the supply circuit, to the center stud (silver colored) of the terminal block (see Figure 15).

4. Secure the L1 (black) and L2 (red) power leads to the outside corresponding terminal block studs (brass colored).

5. Secure one end of the mounted looped neutral wire, located beneath terminal block, to the center stud of the terminal block with nut and keep the other end of the wire screwed into the back of the range.

6. Tighten nuts securely.

The cord kit must be attached to the range back panel with a strain relief which will fit a 1" (25.4mm) diameter hole. If not already equipped, the cord must also have 1/4” (6mm) faston closed-loop lugs attached to the free ends of the individual conductors, preferably soldered in place.

Figure 15: 3-Wire Connection

7. Reinstall the Terminal Block Cover.

English 18

Step 8: Backguard Installation

(optional)

Installation methods will vary upon need. Before you begin read these instructions carefully. Observe all local codes and ordinances.

1. Locate and lightly mark wall studs.

WARNING:

To reduce the risk of fire or injury to persons, check to make sure all packaging has been removed from accessory devices before use.

Backsplash Installation

(PA [30,36, 48] JBS)

The backsplash must be installed prior to installing an overhead hood given that the hood shell covers the top mount-

ing screws of the backsplash.

Parts Included Tools Needed

• Wall studs are usually installed with a 16” or 24”

(406mm or 1372mm) space on center.

2. The height of the hood will determine the height of the top edge of the backsplash. The backsplash should be mounted so that the bottom rear edge of the hood

overlaps the backsplash 1

3. Per each wall stud, use (2) of the provided screws to secure both the top and bottom of the backsplash (see Figure 16).

• Due to variable wall stud widths and varying

backsplash widths, in some cases only one wall stud may be found at the mounting location.

4. Remove protective plastic.

” (38mm).

(10) 1” (25.4mm) screws

(1) Backsplash Tape measure

(1) Installation Guide Pencil

• To protect against scratches, leave protective film on backsplash until after installation is complete.

• If range is already installed, refer to the manufacture’s instructions to disconnect gas and power supplies. Move range forward to gain access to rear of unit.

Phillips screwdriver or drill

42” (1070mm)

all Studs

30”, 36”, 48”

(760mm, 913mm, 1218mm)

Space screws evenly

across top & bottom

Figure 16: Backsplash Installation

English 19

Installing a Backsplash with a Keep Hot Shelf

1. Locate wall studs.

• Wall studs are usually installed with a 16” (406mm) or 24” (1372mm) space on center.

2. The height of the hood will determine the height of the top edge of the backsplash. The backsplash should be mounted so that the bottom rear edge of the Keep Hot

Shelf overlaps the backsplash 11/2” (38mm).

3. At the locations indicated in Figure 18, mount the lower shelf brackets included with the Keep Hot Shelf through the Backsplash and into the wall studs.

• Due to variable wall stud widths and varying

backsplash widths, in some cases, only one wall stud may be found at the mounting location.

4. Remove backsplash protective covering.

5. Start with the Keep Hot Shelf Installation.

Figure 17: Backsplash with a Keep Hot Shelf

A hood can be installed first if the Backsplash is to be installed with a Keep Hot Shelf given that the Keep Hot Shelf covers the top mounting screws of the Backsplash

(Figure 17).

• To protect against scratches, leave protective film on the backsplash until after installation is complete.

• If range is already installed, refer to the manufacture’s instructions to disconnect gas and power supplies. Move range forward to gain access to rear of unit.

Lower Shelf Brackets

Included With Keep Hot Shelf

Figure 18: Backsplash with a Keep Hot Shelf

English 20

Keep Hot Shelf

(KHS [30,36,42,48] QS)

5/8”

(16mm)

Items Included

(352mm)

Edge will slide

30”, 36”, 42”, 48”

(762, 914, 1067, 1219mm)

op Rack

beneath hood

Folds Up

Clip (x2)

” (257mm)

Bottom Rack

Clip (x4)

”

/2”

(343mm)

Keep Hot

Rack (x2)

Figure 19: Keep Hot Shelf

Tools Needed

(12) 1” (25.4mm) screws (4) 1/2” (12.7mm) screws

(4) U-Nuts

(2) Top shelf brackets

(4) Lower shelf brackets

(2) Keep hot racks

(1) Keep hot shelf backsplash

(1) Installation guide & template

Tape measure

Phillips screwdriver or drill

Painter’s Tape

Sharp knife or scissors

Pencil

English 21

1. Tape the templates included with the Keep Hot Shelf to the wall accordingly:

• Tape the sheet titled Left Hand Template to bottom and left end of hood. Align the bottom line of hood with the top line of the template.

• Tape the sheet titled Right Hand Template to bottom and right end of hood. Align the bottom line of hood with the top line of the template.

• Tape the sheet titled Installation Instruction so that the arrow at the top of the template aligns with hood centerline. Align the bottom line of the hood with the top line of the template.

• Left to right sides of the template must be equal to length of shelf.

2. Mount the (2) top shelf brackets and the (3) lower shelf brackets at the locations outlined on the templates. Secure with (10) 1” (25.4mm) screws provided.

3. Cut template out from around the brackets and remove from the wall. Do not discard template before the Keep Hot Shelf is completely installed.

4. Insert (3) U-Nuts onto the (3) lower shelf brackets.

5. Install the wall plate by setting the corner notches (back of wall plate) atop the (2) top shelf brackets. Slide the shelf upwards until the bottom engages with the (3) lower brackets (Figure 20).

Upper shelf bracket (x2)

Lower shelf bracket (x4)

Figure 20: 48” Back of Wall Plate

Notches (x2)

6. Check if the top is properly secured by pulling the top section of the shelf from the wall.

7. Secure to bottom of shelf with the (4) 1/2” (12.7mm) screws provided.

For 48” Keep Hot Shelf

Follow steps 1-6 except use (4) lower brackets which must be spaced equally 15” (381mm) center-to-center.

English 22

Backguard Installation

PRD364JDGU PRD364JDGC PRD366JGU PRD366JGC PRD486JDGU PRD486JDGC PRD48JDSGU PRD48JDSGC

WARNING:

To reduce the risk of fire or injury to persons, check to make sure all packaging has been removed from accessory devices before use.

WARNING:

Fingers or hands could get pinched when installing the backguard. Severe injury could result. Use extreme caution and wear thick protective gloves to avoid potential laceration to finger or hand while sliding the backguard down onto the range.

Pro Grand Pro Grand Pro Grand Pro Grand Pro Grand Pro Grand Pro Grand Pro Grand

AVAILABLE FOR THESE MODELS:

36" Dual Fuel Range 4 Burner Griddle

36" Dual Fuel Range 4 Burner Griddle - Canadian

36" Dual Fuel Range 6 Burner

36" Dual Fuel Range 6 Burner - Canadian

48" Dual Fuel Range 6 Burner Griddle

48" Dual Fuel Range 6 Burner Griddle - Canadian

48" Dual Fuel Range w/ Steam Oven

48" Dual Fuel Range w/ Steam Oven - Canadian

Note: If a backsplash is to be used in addition to a backguard, install the backsplash first and the backguard sec-

ond before sliding range into place.

High Shelf Parts Included

(1) High Shelf top panel

(1) High Shelf front panel

CAUTION:

The High Shelf can get very hot! DO NOT place the following items on top of the High Shelf:

• plastics or containers that can melt

• flammable items

• a total load over 30 pounds (13.6kg)

High Shelf

Low Back

(13) T-20 Torx Stainless screws (16 or 14) T-20 Torx drill point screws

(1) Installation Guide

Low Back Parts Included

(1) Low Back panel

(9 or 8) T-20 Torx stainless screws (8 or 6) T-20 Torx drill point screws

(1) Installation Guide

Tools Needed

T-20 Torx head screwdriver or drill

Figure 21: High Shelf & Low Back Front View

Protective Work Gloves

English 23

4. Begin with Backguard Installation.

Backguard Kit Model Numbers

Model 36” 48” 48” Steam

Low Back PA36JLBG PA48JLBG PA48JLBSG

High Shelf PA36JHSG PA48JHSG PA48JHSSG

Flush Island Trim

The backguard must be attached before sliding the range into the final installed position. When there is less than a 12" (305mm) horizontal clearance between combustible surfaces ∆ and the back edge of the range above the cook-

ing surface, a THERMADOR® Low Back or High Shelf must be purchased separately and installed. When clearance to combustible surfaces ∆ is over 12" (305mm) or for

island installations, the supplied THERMADOR® Flush Island Trim may be used.

Included on Range

High Shelf Assembly

Backguard Installation

High Shelf

Low Back

Mounts inside side panel flange

Flush Island Trim

(Included with range)

Mounts inside side panel flange

(5x) screws along the top

(12x) screws along the back

Figure 22: Backguard Rear View

1. Remove protective plastic.

2. Slide the shelf onto the backguard channel.

3. Install the included (5) stainless screws along the topside of shelf and (8) stainless screws into the back of the shelf.

Mounts inside back panel flange

Figure 23: Backguard Installation

1. Remove protective plastic.

2. Depending on model, remove the (3) or (4) T-20 Torx stainless screws in the front face of the included Flush Island Trim, the (4) drill point screws securing the trim to the side panels, and the (2) or (4) drill point screws securing the piece to the back panel. Lift up to fully remove.

3. Align the back panel of the new accessory with the flanges on the range side panels right and left rear corners. The backguard is inserted inside the guide channels on the back of the range.

4. Make sure the backguard’s front face is outside the flange on the front side of the range.

5. Re-install screws in the new backguard’s front and back panels.

6. Re-install (4) drill point screws to secure the backguard’s back panel to the side panels on the back of the range.

English 24

Step 9: Placing and Leveling the Range

CAUTION:

The top edges of the range’s side panels must be on the same or higher level as the adjacent countertop. If the range is operated while at a lower height relative to the adjacent cabinet, the cabinet could be exposed to excessive temperatures, causing damage to the cabinet and countertop (see Figure 25 on page 26).

For proper performance, the range must be level. This is especially important for all products that have the griddle feature. Priority should be placed on ensuring that the oven cavities are also level for optimum cooking performance.

• Each range has a pair of casters adjacent to the rear legs (see Figure 24). The casters make moving the range easier by slightly lifting the front and allowing the casters to glide the range back towards its installed position.

• The range has (4) leveling legs that are threaded into the cast aluminum base structure. The range is leveled by rotating the legs using an 12” (305mm) adjustable wrench on the flat sides of each foot.

• It is suggested to measure the counter top heights

first with a tape measure and adding an additional 1/16” - 1/8” (2-3mm), then adjusting the legs accordingly prior to pushing the range back to its final location.

• Progression of the height adjustments should be alternated proportionally between the four legs, until the top edges of the range’s side panels are close to matching the countertop height.

• Final height adjustments of the two rear legs take place before moving the range into its installed position in the cabinet.

Caster Locations

Figure 24: Castor Locations

• As the range is moved into its final, installed position, verify that the “hook” on the Anti-Tip Bracket is in a position to engage the back edge of the cast base (see “Step 5: Installing Anti-Tip Device” on page 12). This can be verified by viewing through the opening near the floor.

• With the range in the installed position, the final height adjustments are made to the two front legs to ensure proper alignment to the countertop.

Note: It is assumed that the countertop adjacent to the range has been properly leveled.

English 25

CAUTION! DO NOT operate range if sides are lower than the adjacent cabinet.

This may damage the cabinet and countertop due to excessive temperatures.

CORRECT! Leveling legs should be adjusted so that the range

sides are at the same or higher level as the adjacent cabinet.

Leveling legs can be adjusted

by using an adjustable wrench

on the flats of the legs.

Figure 25: Adjusting the Height of the Range

English 26

Installing the Leg Covers

1. Remove plastic coverings of the stainless steel ‘sleeves’.

2. Place the smaller ‘sleeve’, with cutouts facing up, inside the larger sleeve with the openings of both stacked and facing the back (Figure 26).

3. Beneath the range, wrap the mated pieces around the leg.

4. Slide the outer sleeve up while the inner piece remains on the floor. The mating part has dimples (that you cannot see) for which the holes of the larger sleeve should seize. You should feel a definitive click, letting you know that the apparatus has been mounted to the unit (Figure 27).

5. Repeat for all visible legs.

After the range is properly leveled and the leg covers have been installed, replace the Door Trim and reinstall the Oven Door(s) (“Step 4: Door Removal and Reinstallation” on page 10 for door re-installation).

Figure 26: Leg Covers

Figure 27: Leg Covers Installed

Griddle Tilt Adjustment (Not on all models)

Check the griddle adjustment by pouring two tablespoons of water on the back of the griddle plate. The water should slowly roll into the grease tray. If not, adjust the (2) screws under the back of the griddle plate. Start with one half turn counter-clockwise of the screws. Further adjustment should be made by one-quarter turn until water slowly flows into the grease tray.

Ensure that the burner caps are correctly seated on the burner bases of the range's cooktop.

English 27

Toe Kick Panel (optional)

(PA [36,48] JTKG)

Toe Kick Parts Included

(1) Toe Kick panel

(4) T-20 Torx drill point screws

(1) Installation Guide

Tools Needed

T-20 Torx head screwdriver or drill

Protective Work Gloves

3. Beneath the range, with the holes and flange facing up, wrap the Toe Kick Panel around the cast aluminum base.

4. The mating part has extruded dimples on both sides for which the holes of the Toe Kick Panel should seize. You should feel a definitive snap, letting you know that the part has been installed.

5. Mount the Toe Kick Panel on both sides of the unit into the extruded dimples using the (4) T-20 Torx drill point screws provided.

1. Remove the leg covers by sliding the top, outer sleeve of the leg covers off the extruded dimples of the cast aluminum base (see Figure 26 on page 27).

2. Remove protective plastic covering from the Toe Kick Panel.

Mounting hole locations (x2)

Figure 28: Toe Kick Panel Installation

English 28

+ 67 hidden pages