Texas Instruments TLE2144CDW, TLE2144AMJB, TLE2144AMFKB, TLE2144AIN, TLE2144ACN Datasheet

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

D

Low Noise

10 Hz . . . 15 nV/√Hz
1 kHz . . . 10.5 nV/√Hz

D

10000-pF Load Capability

D

20-mA Min Short-Circuit Output Current

D

27-V/µs Min Slew Rate

D

High Gain-Bandwidth Product . . . 5.9 MHz

D

Low VIO . . . 500 µV Max at 25°C

description

The TLE214x and TLE214xA devices are high-performance, internally compensated operational amplifiers
built using Texas Instruments complementary bipolar Excalibur process. The TLE214xA is a tighter offset
voltage grade of the TLE214x. Both are pin-compatible upgrades to standard industry products.

The design incorporates an input stage that simultaneously achieves low audio-band noise of 10.5 nV/√Hz with
a 10-Hz 1/f corner and symmetrical 40-V/µs slew rate typically with loads up to 800 pF. The resulting low
distortion and high power bandwidth are important in high-fidelity audio applications. A fast settling time of
340 ns to 0.1% of a 10-V step with a 2-kΩ/100-pF load is useful in fast actuator/positioning drivers. Under similar
test conditions, settling time to 0.01% is 400 ns.

D

Single or Split Supply ...4 V to 44 V

D

Fast Settling Time

340 ns to 0.1%
400 ns to 0.01%

D

Saturation Recovery . . . 150 ns

D

Large Output Swing

V

+0.1 V to V

CC–

CC+

– 1 V

The devices are stable with capacitive loads up to 10 nF , although the 6-MHz bandwidth decreases to 1.8 MHz
at this high loading level. As such, the TLE214x and TLE214xA are useful for low-droop sample-and-holds and
direct buffering of long cables, including 4-mA to 20-mA current loops.

The special design also exhibits an improved insensitivity to inherent integrated circuit component mismatches
as is evidenced by a 500-µV maximum offset voltage and 1.7-µV/°C typical drift. Minimum common-mode
rejection ratio and supply-voltage rejection ratio are 85 dB and 90 dB, respectively.

Device performance is relatively independent of supply voltage over the ±2-V to ±22-V range. Inputs can
operate between V

CC–

– 0.3 to V

– 1.8 V without inducing phase reversal, although excessive input current

CC+

may flow out of each input exceeding the lower common-mode input range. The all-npn output stage provides
a nearly rail-to-rail output swing of V

CC–

– 0.1 to V

– 1 V under light current-loading conditions. The device

CC+

can sustain shorts to either supply since output current is internally limited, but care must be taken to ensure
that maximum package power dissipation is not exceeded.

Both versions can also be used as comparators. Differential inputs of V

can be maintained without damage

CC±

to the device. Open-loop propagation delay with TTL supply levels is typically 200 ns. This gives a good
indication as to output stage saturation recovery when the device is driven beyond the limits of recommended
output swing.

Both the TLE214x and TLE214xA are available in a wide variety of packages, including both the
industry-standard 8-pin small-outline version and chip form for high-density system applications. The C-suffix
devices are characterized for operation from 0°C to 70°C, I-suffix devices from –40°C to 105°C, and M-suffix
devices over the full military temperature range of –55°C to 125°C.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

Copyright  1998, Texas Instruments Incorporated

1

TLE214x, TLE214xA, TLE214xY

CHIP

CHIP

0°C to 70°C

40°C to 105°C

TLE2142Y

55°C to 125°C

VIOmax

CHIP FORM

‡

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2141 AVAILABLE OPTIONS

PACKAGED DEVICES

T

A

0°C to 70°C

–40°C to 105°C

–55°C to 125°C

†

The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2141ACDR).

‡

Chip forms are tested at TA = 25°C only.

T

A

°

°

°

–

°

–

†

The D packages are available taped and reeled. Add R suffix to device type (e.g., TLC2142ACDR).

‡

The PW packages are available left-ended taped and reeled. Add LE the suffix to device type (e.g., TLC2142CPWLE).

§

Chip forms are tested at TA = 25°C only.

°

°

VIOmax
AT 25°C

500 µV
900 µV

500 µV
900 µV

500 µV
900 µV

VIOmax
AT 25°C

750 µV TLE2142ACD — — TLE2142ACP —

1200 µV TLE2142CD — — TLE2142CP TLE2142CPWLE

750 µV TLE2142AID — — TLC2142AIP —

1200 µV TLE2142ID — — TLC2142IP —

750 µV TLE2142AMD TLE2142AMFK TLE2142AMJG TLC2142AMP —

1200 µV TLE2142MD TLE2142MFK TLE2142MJG TLC2142MP —

SMALL OUT-

LINE

TLE2141ACD
TLE2141CD

TLE2141AID
TLE2141ID

TLE2141AMD
TLE2141MD

SMALL

OUTLINE

(D)

†

(D)

PACKAGED DEVICES

†

CHIP CARRIER

(FK)

— —

— —

TLE2141AMFK
TLE2141MFK

TLE2142 AVAILABLE OPTIONS

CHIP

CARRIER

(FK)

CERAMIC DIP

TLE2141AMJG
TLE2141MJG

CERAMIC

DIP

(JG)

(JG)

PLASTIC

DIP

(P)

PLASTIC DIP

(P)

TLE2141ACP
TLE2141CP

TLE2141AIP
TLE2141IP

TLE2141AMP
TLE2141MP

TSSOP

(PW)

FORM

(Y)

—

TLE2141Y

—

‡

‡

FORM

(Y)

§

—

—

TLE2144 AVAILABLE OPTIONS

PACKAGED DEVICES

T

A

0°C to 70°C

–40°C to 105°C

–55°C to 125°C

†

The DW packages are available taped and reeled. Add R suffix to device type (e.g., TLE2144CDWR).

‡

Chip forms are tested at TA = 25°C only.

AT 25°C

1.5 mV

2.4 mV

1.5 mV

2.4 mV

1.5 mV

2.5 mV

SMALL OUTLINE

(DW)

—

TLE2144CDW

—

TLE2144IDW

—

TLE2144MDW

†

CHIP CARRIER

TLE2144AMFK
TLE2144MFK

(FK)

—
—

—
—

CERAMIC DIP

(J)

—
—

—
—

TLE2144AMJ
TLE2144MJ

PLASTIC DIP

TLE2144ACN
TLE2144CN

TLE2144AIN
TLE2144IN

TLE2144AMN
TLE2144MN

(N)

(Y)

—

TLE2144Y

—

2

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

D, JG, OR P PACKAGE

OFFSET N1

IN–
IN+

V

CC–

NC

IN–

NC

IN+

NC

TLE2141

(TOP VIEW)

1
2
3
4

TLE2141

FK PACKAGE

(TOP VIEW)

NC

OFFSET N1

NC

NC

3212019

4
5
6
7
8

910111213

NC

NC

CC –

V

NC

8

V

7

CC+

OUT

6

OFFSET N2

5

NC

18
17
16
15
14

NC

NC
V

CC+

NC
OUT
NC

NC
1OUT
1OUT

1IN–
1IN+

V

CC

V

CC

NC

TLE2142

PW PACKAGE

(TOP VIEW)

1
2
3
4
5

–

6
7

–

8

16
15
14
13
12
11
10

9

NC
VCC+
VCC+
2OUT
2IN–
2IN+
2IN+
NC

NC

1IN–

NC

1IN

NC

TLE2142

D, JG, OR P PACKAGE

(TOP VIEW)

1OUT

1IN–
1IN+

V

+

1
2
3
4

CC –

TLE2142

FK PACKAGE

(TOP VIEW)

NC

1OUT

3 2 1 20 19

4
5
6
7
8

910111213

NC

CC –

V

NCNCNC

NC

8
7
6
5

CC +

V

18
17
16
15
14

2IN +

V

CC+

2OUT
2IN–
2IN+

NC
2OUT
NC
2IN–
NC

TLE2144

DW PACKAGE

(TOP VIEW)

1OUT

1IN–

1IN+

V

2IN+

2IN–

2OUT

NC – No internal connection

CC+

NC

1
2
3
4
5
6
7
8

16
15
14
13
12
11
10

9

4OUT
4IN–
4IN+
V
3IN+
3IN–
3OUT
NC

CC

OFFSET N2

TLE2144

J OR N PACKAGE

(TOP VIEW)

1OUT

1IN–
1IN+

–

V

2IN+
2IN–

2OUT

CC+

1
2
3
4
5
6
7

14
13
12
11
10

9
8

4OUT
4IN–
4IN+
V

CC

3IN+
3IN–
3OUT

–

1IN+

NC

V

CC+

NC

2IN+

TLE2144

FK PACKAGE

(TOP VIEW)

1IN –

1OUT

NC

3212019

4
5
6
7
8

910111213

OUTNCOUT

2IN –

4IN –

4OUT

18
17
16
15
14

3IN –

4IN+
NC
VCC–
NC
3IN+

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

3

TLE214x, TLE214xA, TLE214xY
EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

symbol

OFFSET N1
(see Note A)

IN+

IN–

OFFSET N2
(see Note A)

NOTES: A. OFFSET N1 AND OFFSET N2

TLE2141Y chip information

This chip, when properly assembled, displays characteristics similar to the TLE2141. Thermal compression or
ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive
epoxy or a gold-silicon preform.

BONDING PAD ASSIGNMENTS

+

OUT

–

are only availiable on the
TLE2241x devices.

64

(7)

(1)

65

(6)

V

IN+

IN–

(1)
(3)

(2)

(5)

OFFSET N1

(5)

OFFSET N2

CHIP THICKNESS: 15 TYPICAL
BONDING PADS: 4 × 4 MINIMUM
TJmax = 150°C

(4)

(3)(2)

TOLERANCES ARE ±10%.
ALL DIMENSIONS ARE IN MILS.

+

–

V

CC+

CC–

(7)

(4)

(6)

OUT

4

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2142Y chip information

This chip, when properly assembled, displays characteristics similar to the TLE2142. Thermal compression or
ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive
epoxy or a gold-silicon preform.

BONDING PAD ASSIGNMENTS

V

CC+

(1)(2)

(8)

(7)

1IN+

1IN–

2OUT

(3)

(2)

(7)

+

–

V

CC–

(8)

(4)

(1)

(5)

+

(6)

–

1OUT

2IN+

2IN–

90

(3)

(4)

80

(5)

(6)

CHIP THICKNESS: 15 TYPICAL
BONDING PADS: 4 × 4 MINIMUM
TJmax = 150°C
TOLERANCES ARE ±10%.
ALL DIMENSIONS ARE IN MILS.
PIN 4 IS INTERNALLY CONNECTED

TO BACKSIDE OF CHIP.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

5

TLE214x, TLE214xA, TLE214xY
EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2144Y chip information

This chip, when properly assembled, displays characteristics similar to the TLE2144. Thermal compression or
ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive
epoxy or a gold-silicon preform.

V

(3)

(2)

(5)

(6)

(10)

(9)

(12)

(13)

+

+

+

+

–

–

–

–

V

CC+

(4)

(11)

CC–

103

(13)

(14)

(1)

(2)

(12)

(3)

BONDING PAD ASSIGNMENTS

(11)

(4)

140

(10)

(5)

(9)

1IN+

1IN–

2IN+

(8)

2IN–

3IN+

3IN–

(7)

4IN+

4IN–

(6)

CHIP THICKNESS:
15 TYPICAL

BONDING PADS:
4 × 4 MINIMUM

TJmax = 150°C
TOLERANCES ARE ±10%.
ALL DIMENSIONS ARE IN MILS.

(1)

(7)

(8)

(14)

1OUT

2OUT

3OUT

4OUT

6

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

equivalent schematic

V

CC+

POST OFFICE BOX 655303 DALLAS, TEXAS 75265

• 7

IN –

IN+

OFFSET N1

(see Note A)

OFFSET N2

(see Note A)

Q1

R1

R2

Q3

D1

Q4

Q2

R3

Q6

Q5

Q7

Q8

R5

R4

C1

Q9

Q10

R6

Q11

Q12

D2

Q14

Q13

R7

R8

Q15

Q16

R10

R9

Q17

C2

R11

Q18

Q19

R12

R14 R18 R19

Q22

Q26

Q25

Q27

Q28

D6

D7

Q29

Q20

D3

Q21

C4

C3

D4

R13

Q23

R15 R17

R16

Q24

D5

D8

Q30

Q31

Q32

Q33

R20

Q34

Q35

R21

R24

Q37

R23

Q36

OUT

PRECISION OPERATIONAL AMPLIFIERS

EXCALIBUR LOW-NOISE HIGH-SPEED

R22

SLOS183A – FEBRUAR Y 1997 – REVISED MARCH 1998

TLE214x, TLE214xA, TLE214xY

V

NOTE A: OFFSET N1 AND OFFSET N2 are only availiable on the TLE2241x devices.

ACTUAL DEVICE COMPONENT COUNT

COMPONENT TLE2241 TLE2242 TLE2244

Transistors 46 65 130
Resistors 24 43 86
Diodes 8 14 28
Capacitors 4 8 16
Epi-FET 1 1 2

CC–

TLE214x, TLE214xA, TLE214xY

PACKAGE

A

UNIT

Common-mode input voltage, V

V

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)

Supply voltage, V
Supply voltage, V
Differential input voltage, V
Input voltage range, VI (any input) V

Input current, II (each input) ±1 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Output current, IO ±80 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Total current into V
Total current out of V

Duration of short-circuit current at (or below) 25°C (see Note 3) unlimited. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Continuous total dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating free-air temperature range, TA: C suffix 0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Storage temperature range –65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Case temperature for 60 seconds: FK package 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, DW, N, P, or PW package 260°C. . . . .

Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J or JG package 300°C. . . . . . . . . . . . . . . .

†

Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between V

2. Differential voltages are at IN+ with respect to IN–. Excessive current flows if input is brought below V

3. The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum
dissipation rating is not exceeded.

(see Note 1) 22 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CC+

–22 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CC–

CC+

CC–

(see Note 2) ±44 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ID

CC+

to V

80 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

80 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

I suffix –40°C to 105°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

M suffix –55°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CC+

and V

CC–

CC–

.
– 0.3 V.

CC–

– 0.3 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

†

T

≤ 25°C DERATING FACTOR T

POWER RATING ABOVE TA = 25°CAPOWER RATINGAPOWER RATINGAPOWER RATING

D 725 mW 5.8 mW/°C 464 mW 261 mW 145 mW

DW 1025 mW 8.2 mW/°C 656 mW 369 mW 205 mW

FK 1375 mW 11.0 mW/°C 880 mW 495 mW 275 mW

J 1375 mW 1 1.0 mW/°C 880 mW 495 mW 275 mW

JG 1050 mW 8.4 mW/°C 672 mW 378 mW 210 mW

N 1150 mW 9.2 mW/°C 736 mW 414 mW 230 mW
P 1000 mW 8.0 mW/°C 640 mW 360 mW 200 mW

PW 525 mW 4.2 mW/°C 336 mW — —

recommended operating conditions

Supply voltage, V

Operating free-air temperature, T

CC±

p

VCC = 5 V 0 2.9 0 2.7 0 2.7

IC

V

= ±15 V –15 12.9 –15 12.7 –15 12.7

CC±

A

DISSIPATION RATING TABLE

= 70°C T

C SUFFIX I SUFFIX M SUFFIX
MIN MAX MIN MAX MIN MAX

= 105°C T

±2 ±22 ±2 ±22 ±2 ±22 V

0 70 –40 105 –55 125 °C

= 125°C

8

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

VIOInput offset voltage

V

,

Full range

1.7

1.7µV/°C

V

O

2.5 V

R

S

Ω,

IIOInput offset current

nA

IIBInput bias current

A

0to0.3to0to0.3

V

R

Ω

V

0to0

g

I

150 µA

VOHHigh-level output voltage

I

mA

V

I

mA

I

150 µA

mV

VOLLow-level output voltage

I

mA

I

mA

V

A

gg

CC

,

L

,

V/mV

CMRR

j

V

V

min, R

50 Ω

dB

k

ygj

CC±

,

dB

ICCSupply current

O

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2141C electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)

TLE2141C TLE2141AC

MIN TYP MAX MIN TYP MAX

µ

°

µ

0 –0.3 0 –0.3

to

3 3.2 3 3.2
0 0

to

2.9 2.9

MΩ

Ω

p

α

r
c

z

†

Full range is 0°C to 70°C.

Temperature coefficient of

VIO

input offset voltage

p

p

Common-mode input

ICR

voltage range

Large-signal differential V

VD

voltage amplification
Input resistance 25°C 70 70

i

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop output

o

impedance
Common-mode rejection

ratio
Supply-voltage rejection V

SVR

ratio (∆V

CC±

pp

p

p

/∆VIO)

A

25°C 225 1400 200 1000

Full range 1700 1300

= 2.5 V R

V
VIC = 2.5 V

= 50

S

= –

OH

= –1.5

OH

= –15

OH

=

OL

= 1.5

OL

= 15

OL

= ±2.5 V , R

VO = 1 V to –1.5 V

f = 1 MHz 25°C 30 30

=

IC

ICR

= ±2.5 V to ±15 V,

RS = 50 Ω
VO = 2.5 V, No load,

VIC = 2.5 V

= 50 Ω

50

= 2 kΩ,

=

S

25°C 8 100 8 100

Full range 150 150

25°C –0.8 –2 –0.8 –2

Full range –2.1 –2.1

25°C

Full range

25°C 3.9 4.1 3.9 4.1

Full range 3.8 3.8

25°C 3.8 4 3.8 4

Full range 3.7 3.7

25°C 3.2 3.7 3.2 3.7

Full range 3.2 3.2

25°C 75 125 75 125

Full range 150 150

25°C 150 225 150 225

Full range 250 250

25°C 1.2 1.6 1.2 1.6

Full range 1.7 1.7

25°C 50 220 50 220

Full range 25 25

25°C 85 118 85 118

Full range 80 80

25°C 90 106 90 106

Full range 85 85

25°C 3.4 4.4 3.4 4.4

Full range 4.6 4.6

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

9

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

†

VD

,

L

,

V/µs

tsSettling time

VD

,

s

VnEquivalent input noise voltage

V/√H

V

q

V

InEquivalent input noise current

A/√H

†

,

THD

N

V

O

V,

R

L

kΩ ,

0.0052%

0.0052%
B1Unity-gain bandwidth

R

kΩ

†

C

100 pF

†

5.9

5.9

MH

†

,

†

,

Gain-bandwidth product

R

L

kΩ ,

C

L

100 F,

5.8

5.8

MH

,

B

g

V

O(PP)

V,

L

,

660

660

kH

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2141C operating characteristics, VCC = 5 V, TA = 25°C

MIN TYP MAX MIN TYP MAX

SR+ Positive slew rate
SR– Negative slew rate

p

N(PP)

OM

φ

m

†

RL and CL terminated to 2.5 V .

Peak-to-peak equivalent input
noise voltage

p

Total harmonic distortion

+

plus noise

Maximum output-swing
bandwidth

Phase margin at unity gain RL = 2 kن, CL = 100 pF

A

= –1, R

= –1,

= 2 V

2

†,

,

CL = 500 pF
A

2.5-V step
RS = 20 Ω, f = 10 Hz 15 15

RS = 20 Ω, f = 1 kHz 10.5 10.5
f = 0.1 Hz to 1 Hz 0.48 0.48
f = 0.1 Hz to 10 Hz
f = 10 Hz 1.92 1.92
f = 1 kHz 0.5 0.5

V

= 1 V to 3 V,R

1 V to 3

AVD = 2,

= 2

L

R

= 2 kΩ

p

2

f = 100 kHz
V

AVD = 1,

= 2 kΩ,

To 0.1% 0.16 0.16
To 0.01% 0.22 0.22

= 2 kΩ

2

f = 10 kHz

=

L

C

= 100 pF

R

= 2 kن,

CL = 100 pF

, 45 45

p

†
†

TLE2141C TLE2141AC

42 42

0.51 0.51

57° 57°

µ

n

z

µ

p

z

z

z

z

10

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

VIOInput offset voltage

V

,

,

Full range

1.7

1.7µV/°C

V

IC

0,

R

S

Ω,

IIOInput offset current

nA

IIBInput bias current

A

15to15.3to15to15.3

V

R

Ω

V

15to15.3to15to15.3

g

I

150 µA

V

I

mA

V

I

mA

I

150 µA

V
s

g

I

mA

V

swing

I

mA

A

gg

V

±10 V

V/mV

CMRR

V

V

min

R

50 Ω

dB

k

CC±

,

dB

I

V

0

25°C

mA

ICCSupply current

V

No load

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2141C electrical characteristics at specified free-air temperature, V
otherwise noted)

TLE2141C TLE2141AC

MIN TYP MAX MIN TYP MAX

–15 –15.3 –15 –15.3

13 13.2 13 13.2

–15 –15.3 –15 –15.3

12.9 13.1 12.9 13.1

–25 –50 –25 –50

20 31 20 31

p

α

r
c

z

OS

†

Full range is 0°C to 70°C.

Temperature coefficient

VIO

of input offset voltage

p

p

Common-mode input

ICR

voltage range

Maximum positive peak

OM+

output voltage swing

Maximum negative
p

peak output voltage

OM–

Large-signal differential

VD

voltage amplification
Input resistance RL = 2 kΩ 25°C 65 65

i

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop output

o

impedance
Common-mode

rejection ratio
Supply-voltage

rejection ratio

SVR

(∆V
Short-circuit output

current

win

CC±

pp

p

/∆VIO)

A

25°C 200 900 175 500

Full range 1300 800

= 0

V
VO = 0

= 50

S

= –

O

= –1.5

O

= –15

O

=

O

= 1.5

O

= 15

O

=

O

f = 1 MHz 25°C 30 30

=

IC

ICR

V

= ±2.5 V to ±15 V,

RS = 50 Ω

=

O

= 0,

O

R

,

S

VID = 1 V
VID = –1 V

= 50 Ω

50

=

25°C 7 100 7 100

Full range 150 150

25°C –0.7 –1.5 –0.7 –1.5

Full range –1.6 –1.6

25°C

Full range

25°C 13.8 14.1 13.8 14.1

Full range 13.7 13.7

25°C 13.7 14 13.7 14

Full range 13.6 13.6

25°C 13.1 13.7 13.1 13.7

Full range 13 13

25°C –14.7 –14.9 –14.7 –14.9

Full range –14.6 –14.6

25°C –14.5 –14.8 –14.5 –14.8

Full range –14.4 –14.4

25°C –13.4 –13.8 –13.4 –13.8

Full range –13.3 –13.3

25°C 100 450 100 450

Full range 75 75

25°C 85 108 85 108

Full range 80 80

25°C 90 106 90 106

Full range 85 85

°

25°C 3.5 4.5 3.5 4.5

Full range 4.7 4.7

= ±15 V (unless

CC±

to

to

µ

°

µ

MΩ

Ω

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

11

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

VD

,

L

,

V/µs

tsSettling time

VD

,

s

VnEquivalent input noise voltage

V/√H

V

q

V

InEquivalent input noise current

A/√H

THD

N

O(PP)

,

L

,

0.01%

0.01%

Gain-bandwidth product

L

,

L

,

5.9

5.9

MH

B

g

O(PP)

,

L

,

668

668

kH

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2141C operating characteristics, V

SR+ Positive slew rate
SR– Negative slew rate

p

N(PP)

B

1

OM

φ

m

Peak-to-peak equivalent input
noise voltage

p

Total harmonic distortion plus V

+

noise
Unity-gain bandwidth RL = 2 kΩ, CL = 100 pF 6 6 MHz

Maximum output-swing V
bandwidth

Phase margin at unity gain RL = 2 kΩ, CL = 100 pF

p

A

= –1, R

CL = 500 pF
A

= –1,

10-V step
RS = 20 Ω, f = 10 Hz 15 15

RS = 20 Ω, f = 1 kHz 10.5 10.5
f = 0.1 Hz to 1 Hz 0.48 0.48
f = 0.1 Hz to 10 Hz
f = 10 Hz 1.89 1.89
f = 1 kHz 0.47 0.47

AVD = 10,

R

= 2 kΩ, C

f = 100 kHz

AVD = 1,

= ±15 V, TA = 25°C

CC±

= 2 kΩ,

To 0.1% 0.34 0.34
To 0.01% 0.4 0.4

= 20 V, R

= 20 V, R

= 2 kΩ,

f = 10 kHz

= 100 pF,

= 2 kΩ,

CL = 100 pF

TLE2141C TLE2141AC

MIN TYP MAX MIN TYP MAX

27 45 27 45
27 42 27 42

0.51 0.51

58° 58°

µ

n

z

µ

p

z

z

z

12

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

VIOInput offset voltage

V

,

Full range

1.7

1.7µV/°C

V

O

2.5 V,

R

S

Ω,

IIOInput offset current

nA

IIBInput bias current

A

0to0.3to0to0.3

V

R

Ω

V

0to0

g

I

150 µA

VOHHigh-level output voltage

I

mA

V

I

mA

I

150 µA

mV

VOLLow-level output voltage

I

mA

I

mA

V

A

gg

CC

,

L

,

V/mV

CMRR

V

V

min,R

50 Ω

dB

k

ygj

CC±

,

dB

ICCSupply current

O

,

,

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2142C electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)

TLE2142C TLE2142AC

MIN TYP MAX MIN TYP MAX

µ

°

µ

0 –0.3 0 –0.3

to

3 3.2 3 3.2
0 0

to

2.9 2.9

MΩ

Ω

p

α

r
c

z

†

Full range is 0°C to 70°C.

Temperature coefficient of

VIO

input offset voltage

p

p

Common-mode input

ICR

voltage range

Large-signal differential V

VD

voltage amplification
Input resistance 25°C 70 70

i

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop output

o

impedance
Common-mode

rejection ratio
Supply-voltage rejection V

SVR

ratio (∆V

CC±

pp

p

p

/∆VIO)

A

25°C 220 1900 200 1500

Full range 2200 1800

= 2.5 V,R

V
VIC = 2.5 V

= 50

S

= –

OH

= –1.5

OH

= –15

OH

=

OL

= 1.5

OL

= 15

OL

= ±2.5 V , R

VO = 1 V to –1.5 V

f = 1 MHz 25°C 30 30

=

IC

ICR

= ±2.5 V to ±15 V,

RS = 50 Ω
V

= 2.5 V, No load,

VIC = 2.5 V

= 50 Ω

50

= 2 kΩ,

=

S

25°C 8 100 8 100

Full range 150 150

25°C –0.8 –2 –0.8 –2

Full range –2.1 –2.1

25°C

Full range

25°C 3.9 4.1 3.9 4.1

Full range 3.8 3.8

25°C 3.8 4 3.8 4

Full range 3.7 3.7

25°C 3.4 3.7 3.4 3.7

Full range 3.4 3.4

25°C 75 125 75 125

Full range 150 150

25°C 150 225 150 225

Full range 250 250

25°C 1.2 1.4 1.2 1.4

Full range 1.5 1.5

25°C 50 220 50 220

Full range 25 25

25°C 85 118 85 118

Full range 80 80

25°C 90 106 90 106

Full range 85 85

25°C 6.6 8.8 6.6 8.8

Full range 9.2 9.2

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

13

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

,

†

,

A

VD

1,

R

L

kΩ ,

V/µs

tsSettling time

VD

,

s

VnEquivalent input noise voltage

V/√H

V

q

V

InEquivalent input noise current

A/√H

†

,

THD

N

O

,

R

L

kΩ ,

0.0052%

0.0052%
†

,

,

Gain-bandwidth product

R

L

kΩ ,

C

L

100 F,

5.8

5.8

MH

,

B

g

V

O(PP)

V,

L

,

660

660

kH

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2142C operating characteristics, VCC = 5 V, TA = 25°C

SR+ Positive slew rate
SR– Negative slew rate

p

N(PP)

B1 Unity-gain bandwidth

OM

φ

m

†

RL terminates at 2.5 V .

Peak-to-peak equivalent
input noise voltage

p

Total harmonic distortion plus V

+

noise

p

Maximum output-swing
bandwidth

Phase margin at unity gain RL = 2 kن, CL = 100 pF

A

= –1

CL = 500 pF
A

= –1,

2.5-V step
RS = 20 Ω, f = 10 Hz 15 15

RS = 20 Ω, f = 1 kHz 10.5 10.5
f = 0.1 Hz to 1 Hz 0.48 0.48
f = 0.1 Hz to 10 Hz
f = 10 Hz 1.92 1.92
f = 1 kHz 0.5 0.5

= 1 V to 3 V,

AVD = 2,
RL = 2 kن,
R

= 2 kΩ

2

f = 100 kHz
V

= 2 V

2

AVD = 1,

R

= 2 kΩ

2

To 0.1% 0.16 0.16
To 0.01% 0.22 0.22

R

= 2 kΩ

2

f = 10 kHz
CL = 100 pF 5.9 5.9 MHz

C

= 100 pF

R

= 2 kن,

CL = 100 pF

TLE2142C TLE2142AC

MIN TYP MAX MIN TYP MAX

45 45
42 42

0.51 0.51

57° 57°

µ

n

z

µ

p

z

z

z

14

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

VIOInput offset voltage

V

,

Full range

1.7

1.7µV/°C

V

IC

0,

R

S

IIOInput offset current

nA

IIBInput bias current

A

15to15.3to15to15.3

V

R

Ω

V

15to15.3to15to15.3

g

I

150 µA

V

I

mA

V

I

mA

I

150 µA

V

g

I

mA

V

I

mA

A

gg

V

±10 V

V/mV

CMRR

IC ICR

,

dB

k

ygj

CC±

,

dB

IOSShort-circuit output current

V

0

25°C

A

ICCSupply current

V

No load

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2142C electrical characteristics at specified free-air temperature, V
otherwise noted)

TLE2142C TLE2142AC

MIN TYP MAX MIN TYP MAX

7 100 7 100

–15 –15.3 –15 –15.3

13 13.2 13 13.2

–15 –15.3 –15 –15.3

12.9 13.1 12.9 13.1

–25 –50 –25 –50

20 31 20 31

p

α

r

i

c
z

†

Full range is 0°C to 70°C.

Temperature coefficient of

VIO

input offset voltage

p

p

Common-mode input

ICR

voltage range

Maximum positive peak

OM+

output voltage swing

Maximum negative peak

OM–

output voltage swing

Large-signal differential

VD

voltage amplification
Input resistance RL = 2 kΩ 25°C 65 65 MΩ

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop output

o

impedance
Common-mode V

rejection ratio
Supply-voltage rejection V

SVR

ratio (∆V

CC±

pp

/∆VIO)

p

A

25°C 290 1200 275 750

Full range 1600 1200

= 0

V
VO = 0

= 50

S

= –

O

= –1.5

O

= –15

O

=

O

= 1.5

O

= 15

O

=

O

f = 1 MHz 25°C 30 30

= V

RS = 50 Ω

= ± 2.5 V to ±15 V,

RS = 50 Ω

=

O

= 0,

O

min,

VID = 1 V
VID = –1 V

=

= 50 Ω,

25°C

Full range 150 150

25°C –0.7 –1.5 –0.7 –1.5

Full range –1.6 –1.6

25°C

Full range

25°C 13.8 14.1 13.8 14.1

Full range 13.7 13.7

25°C 13.7 14 13.7 14

Full range 13.6 13.6

25°C 13.3 13.7 13.3 13.7

Full range 13.2 13.2

25°C –14.7 –14.9 –14.7 –14.9

Full range –14.6 –14.6

25°C –14.5 –14.8 –14.5 –14.8

Full range –14.4 –14.4

25°C –13.4 –13.8 –13.4 –13.8

Full range –13.3 –13.3

25°C 100 450 100 450

Full range 75 75

25°C 85 108 85 108

Full range 80 80

25°C 90 106 90 106

Full range 85 85

°

25°C 6.9 9 6.9 9

Full range 9.4 9.4

= ±15 V (unless

CC±

to

to

µ

°

µ

Ω

m

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

15

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

VD

,

L

,

V/µs

tsSettling time

VD

,

s

VnEquivalent input noise voltage

V/√H

V

q

V

InEquivalent input noise current

A/√H

THD

N

O(PP)

,

L

,

0.01%

0.01%

Gain-bandwidth product

L

,,

L

,

5.9

5.9

MH

B

g

O(PP)

,

L

,

668

668

kH

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2142C operating characteristics, V

SR+ Positive slew rate
SR– Negative slew rate

p

N(PP)

B

1

OM

φ

m

Peak-to-peak equivalent input
noise voltage

p

Total harmonic distortion plus V

+

noise
Unity-gain bandwidth RL = 2 kΩ, CL = 100 pF 6 6 MHz

Maximum output-swing V
bandwidth

Phase margin at unity gain RL = 2 kΩ, CL = 100 pF

p

A

= –1, R

CL = 500 pF
A

= –1,

10-V step
RS = 20 Ω, f = 10 Hz 15 15

RS = 20 Ω, f = 1 kHz 10.5 10.5
f = 0.1 Hz to 1 Hz 0.48 0.48
f = 0.1 Hz to 10 Hz
f = 10 Hz 1.89 1.89
f = 1 kHz 0.47 0.47

= 20 V, R

AVD = 10,

R

= 2 kΩ,, C

f =100 kHz

= 20 V, R

AVD = 1,

= ±15 V, TA = 25°C

CC±

TLE2142C TLE2142AC

MIN TYP MAX MIN TYP MAX

= 2 kΩ,

To 0.1% 0.34 0.34
To 0.01% 0.4 0.4

= 2 kΩ,

f = 10 kHz

= 100 pF,

= 2 kΩ,

CL = 100 pF

27 45 27 45
27 42 27 42

0.51 0.51

58° 58°

µ

n

z

µ

p

z

z

z

16

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

V

I

t offset

mV

Full range

1.7

1.7µV/°C

V

O

2.5 V,

R

50 Ω

IIOInput offset current

nA

IIBInput bias current

A

V

R

Ω

V

g

I

150 µA

V

g

I

mA

V

I

15 mA

I

150 µA

mV

V

I

mA

I

mA

V

A

gg

CC

,

L

,

V/mV

CMRR

V

V

min

R

50 Ω

dB

k

rejection ratio

CC±

,

dB

ICCSupply current

O

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2144C electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)

TLE2144C TLE2144AC

MIN TYP MAX MIN TYP MAX

°

8 100 8 100

µ

0 –0.3 0 –0.3

to to to to

3 3.2 3 3.2
0 0

to to

2.9 2.9

p

npu

IO

α

r
c

z

†

Full range is 0°C to 70°C.

Temperature coefficient

VIO

of input offset voltage

p

p

Common-mode input

ICR

voltage range

High-level output

OH

voltage

Low-level output

OL

voltage

Large-signal differential V

VD

voltage amplification
Input resistance 25°C 70 70 MΩ

i

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop output

o

impedance
Common-mode

rejection ratio
Supply-voltage

SVR

(∆V

pp

CC±

voltage

/∆VIO)

A

25°C 0.5 3.8 0.5 3

Full range 4.4 3.6

= 2.5 V,

V
VIC = 2.5 V

S

OH

OH

OH

OL

OL

OL

VO = 1 V to –1.5 V

f = 1 MHz 25°C 30 30 Ω

IC

V
RS = 50 Ω

VO = 2.5 V, No load,
VIC = 2.5 V

= 50

= –

= –1.5

= –

=

= 1.5

= 15

= ±2.5 V , R

=

= ±2.5 V to ±15 V,

ICR

,

=

S

=

S

= 2 kΩ,

,

25°C

Full range 150 150

25°C –0.8 –2 –0.8 –2

Full range –2.1 –2.1

25°C

Full range

25°C 3.9 4.1 3.9 4.1

Full range 3.8 3.8

25°C 3.8 4 3.8 4

Full range 3.7 3.7

25°C 3.4 3.7 3.4 3.7

Full range 3.4 3.4

25°C 75 125 75 125

Full range 150 150

25°C 150 225 150 225

Full range 250 250

25°C 1.2 1.6 1.2 1.6

Full range 1.7 1.7

25°C 50 95 50 95

Full range 25 25

25°C 85 118 85 118

Full range 80 80

25°C 90 106 90 106

Full range 85 85

25°C 13.2 17.6 13.2 17.6

Full range 18.5 18.5

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

17

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

L

V/µs

tsSettling time

s

V

q
V/√H

V

q

V

I

q
A/√H

THD

N

O

,

L

,

0.0052%

0.0052%

Gain-bandwidth product

L

,

L

,

5.8

5.8

MH

B

g

O(PP)

,

L

,

660

660

kH

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2144C operating characteristics, VCC = 5 V, TA = 25°C

SR+ Positive slew rate
SR– Negative slew rate

n

N(PP)

n

B

1

OM

φ

m

†

RL terminates at 2.5 V

Equivalent input
noise voltage

Peak-to-peak equivalent
input noise voltage

Equivalent input
noise current

Total harmonic distortion plus V

+

noise
Unity-gain bandwidth

Maximum output-swing
bandwidth

Phase margin at unity gain

p

AVD = –1,
CL = 500 pF

AVD = –1, T o 0.1% 0.16 0.16

2.5-V step To 0.01% 0.22 0.22
RS = 20 Ω, f = 10 Hz 15 15
RS = 20 Ω,
f = 0.1 Hz to 1 Hz 0.48 0.48
f = 0.1 Hz to 10 Hz
f = 10 Hz 1.92 1.92
f = 1 kHz

= 1 V to 3 V,

AVD = 2,
RL = 2 kن,
R

= 2 kن,

f = 100 kHz
V

= 2 V,

AVD = 1,
RL = 2 kن,

RL = 2 kن,

f = 1 kHz 10.5 10.5

R

= 2 kن,

f = 10 kHz
CL = 100 pF 5.9 5.9 MHz
C

= 100 pF,

R

= 2 kن,

CL = 100 pF
CL = 100 pF 57° 57°

TLE2144C TLE2144AC

MIN TYP MAX MIN TYP MAX

45 45
42 42

0.51 0.51

0.5 0.5

µ

n

z

µ

p

z

z

z

18

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

V

I

t offset

mV

,

Full range

1.7

1.7µV/°C

V

IC

0,

R

S

IIOInput offset current

nA

IIBInput bias current

A

V

R

Ω

V

g

I

150 µA

V

I

mA

V

I

15 mA

I

150 µA

V

peak output voltage

g

I

mA

V

swing

I

mA

A

gg

V

±10 V

V/mV

CMRR

V

V

min

R

50 Ω

dB

k

rejection ratio

CC±

,

dB

I

V

0

25°C

mA

ICCSupply current

V

0

No load

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2144C electrical characteristics at specified free-air temperature, V
otherwise noted)

TLE2144C TLE2144AC

MIN TYP MAX MIN TYP MAX

7 100 7 100

–15 –15.3 –15 –15.3

to to to to

13 13.2 13 13.2

–15 –15.3 –15 –15

to to to to

12.9 13.1 12.9 13.1

–25 –50 –25 –50

20 31 20 31

p

npu

IO

α

r
c

z

OS

†

Full range is 0°C to 70°C.

Temperature coefficient

VIO

of input offset voltage

p

p

Common-mode input

ICR

voltage range

Maximum positive peak

OM+

output voltage swing

Maximum negative
p

OM–

swin

Large-signal differential

VD

voltage amplification
Input resistance RL = 2 kΩ 25°C 65 65 MΩ

i

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop output

o

impedance
Common-mode

rejection ratio
Supply-voltage

SVR

(∆V
Short-circuit output

current

pp

CC±

voltage

p

/∆VIO)

A

25°C 0.6 2.4 0.5 1.5

Full range 3.2 2.4

= 0

V
VO = 0

= 50

S

= –

O

= –1.5

O

= –

O

=

O

= 1.5

O

= 15

O

=

O

f = 1 MHz 25°C 30 30 Ω

=

IC

ICR

V

= ±2.5 V to ±15 V,

RS = 50 Ω

=

O

,

=

O

R

,

S

VID = 1 V
VID = –1 V

= 50 Ω,

50 Ω,

=

25°C

Full range 150 150

25°C –0.7 –1.5 –0.7 –1.5

Full range –1.6 –1.6

25°C

Full range

25°C 13.8 14.1 13.8 14.1

Full range 13.7 13.7

25°C 13.7 14 13.7 14

Full range 13.6 13.6

25°C 13.1 13.7 13.1 13.7

Full range 13 13

25°C –14.7 –14.9 –14.7 –14.9

Full range –14.6 –14.6

25°C –14.5 –14.8 –14.5 –14.8

Full range –14.4 –14.4

25°C –13.4 –13.8 –13.4 –13.8

Full range –13.3 –13.3

25°C 100 170 100 170

Full range 75 75

25°C 85 108 85 108

Full range 80 80

25°C 90 106 90 106

Full range 85 85

°

25°C 13.8 18 13.8 18

Full range 18.8 18.8

= ±15 V (unless

CC±

°

µ

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

19

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

VD

,

L

,

V/µs

tsSettling time

VD

,

s

VnEquivalent input noise voltage

V/√H

V

q

V

InEquivalent input noise current

A/√H

THD

N

O(PP)

,

L

,

0.01%

0.01%

Gain-bandwidth product

L

,

L

,

5.9

5.9

MH

B

g

O(PP)

,

L

,

668

668

kH

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2144C operating characteristics, V

SR+ Positive slew rate
SR– Negative slew rate

p

N(PP)

B

1

OM

φ

m

Peak-to-peak equivalent input
noise voltage

p

Total harmonic distortion plus V

+

noise
Unity-gain bandwidth RL = 2 kΩ, CL = 100 pF 6 6 MHz

Maximum output-swing V
bandwidth

Phase margin at unity gain RL = 2 kΩ, CL = 100 pF 58° 58°

p

A

= –1, R

CL = 500 pF
A

= –1,

10-V step
RS = 20 Ω, f = 10 Hz 15 15

RS = 20 Ω, f = 1 kHz 10.5 10.5
f = 0.1 Hz to 1 Hz 0.48 0.48
f = 0.1 Hz to 10 Hz
f = 10 Hz 1.89 1.89
f = 1 kHz 0.47 0.47

AVD = 10,

R

= 2 kΩ, C

f = 100 kHz

AVD = 1,

= ±15 V, TA = 25°C

CC±

= 2 kΩ,

To 0.1% 0.34 0.34
To 0.01% 0.4 0.4

= 20 V, R

= 20 V, R

= 2 kΩ,

f = 10 kHz

= 100 pF,

= 2 kΩ,

CL = 100 pF

TLE2144C TLE2144AC

MIN TYP MAX MIN TYP MAX

27 45 27 45
27 42 27 42

0.51 0.51

µ

n

z

µ

p

z

z

z

20

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

VIOInput offset voltage

V

,

,

Full range

1.7

1.7µV/°C

V

O

2.5 V,

R

S

Ω,

IIOInput offset current

nA

IIBInput bias current

A

0to0.3to0to0.3

V

R

Ω

V

0to0.3to0to0.3

g

VOHHigh-level output voltage

V

mV

VOLLow-level output voltage

mV

A

gg

CC

,

L

,

V/mV

CMRR

V

V

min, R

50 Ω

dB

k

ygj

CC±

,

dB

ICCSupply current

O

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2141I electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)

TLE2141I TLE2141AI

MIN TYP MAX MIN TYP MAX

µ

°

µ

0 –0.3 0 –0.3

to

3 3.2 3 3.2
0 –0.3 0 –0.3

to

2.7 2.9 2.7 2.9

3.8 4 3.8 4

3.7 3.7

150 225 150 225

225 225

MΩ

Ω

p

α

r
c

z

†

Full range is –40°C to 105°C.

Temperature coefficient

VIO

of input offset voltage

p

p

Common-mode input

ICR

voltage range

p

p

Large-signal differential V

VD

voltage amplification
Input resistance 25°C 70 70

i

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop output

o

impedance
Common-mode

rejection ratio
Supply-voltage rejection V

SVR

ratio (∆V

pp

CC±

/∆VIO)

A

25°C 225 1400 200 1000

Full range 1900 1500

= 2.5 V

V
VIC = 2.5 V

= 50

S

IOH = –150 µA 3.9 4.1 3.9 4.1
IOH = –1.5 mA
IOH = –15 mA 3.2 3.7 3.2 3.7
IOH = –100 µA 3.8 3.8
IOH = –1 mA
IOH = –10 mA 3.3 3.3
IOL = 150 µA 75 125 75 125
IOL = 1.5 µA
IOL = 15 mA 1.2 1.6 1.2 1.6 V
IOL = 100 µA 175 175
IOL = 1 mA
IOL = 10 mA 1.4 1.4 V

= ±2.5 V , R

VO = 1 V to –1.5 V

f = 1 MHz 25°C 30 30

=

IC

ICR

= ±2.5 V to ±15 V,

RS = 50 Ω
VO = 2.5 V, No load,

VIC = 2.5 V

R

=

S

= 50 Ω

50

= 2 kΩ,

25°C 8 100 8 100

Full range 200 200

25°C –0.8 –2 –0.8 –2

Full range –2.2 –2.2

25°C

Full range

25°C

Full range

25°C

Full range

25°C 50 220 50 220

Full range 10 10

25°C 85 118 85 118

Full range 80 80

25°C 90 106 90 106

Full range 85 85

25°C 3.4 4.4 3.4 4.4

Full range 4.6 4.6

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

21

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

,

†

,

A

VD

1,

R

L

kΩ ,

V/µs

tsSettling time

VD

,

s

VnEquivalent input noise voltage

V/√H

V

q

V

InEquivalent input noise current

A/√H

,

†

,

THD

N

V

O

V,

R

L

kΩ ,

0.0052%

0.0052%
†

†

,

Gain-bandwidth product

R

L

kΩ

C

L

100 F,

5.8

5.8

MH

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2141I operating characteristics, VCC = 5 V, T

SR+ Positive slew rate
SR– Negative slew rate

p

N(PP)

B

1

B

OM

φ

m

†

RL and CL terminated to 2.5 V .

Peak-to-peak equivalent input
noise voltage

p

Total harmonic distortion plus

+

noise
Unity-gain bandwidth RL = 2 kن, CL = 100 pF

Maximum output-swing
bandwidth

Phase margin at unity gain RL = 2 kن, CL = 100 pF

p

A

= –1

CL = 500 pF
A

= –1,

2.5-V step
RS = 20 Ω, f = 10 Hz 15 15

RS = 20 Ω, f = 1 kHz 10.5 10.5
f = 0.1 Hz to 1 Hz 0.48 0.48
f = 0.1 Hz to 10 Hz
f = 10 Hz 1.92 1.92
f = 1 kHz 0.5 0.5

V

= 1 V to 3 V

1 V to 3

AVD = 2,

R

= 2 kΩ

2

f = 100 kHz
V

= 2 V,

O(PP)

AVD = 1,

R

= 2 kΩ

2

To 0.1% 0.16 0.16
To 0.01% 0.22 0.22

R

= 2 kΩ

2

f = 10 kHz

C

= 100 pF

RL = 2 kن,
CL = 100 pF

= 25°C

A

TLE2141I TLE2141AI

MIN TYP MAX MIN TYP MAX

45 45
42 42

0.51 0.51

†

†
†

5.9 5.9 MHz

660 660 kHz

57° 57°

µ

n

z

µ

p

z

z

22

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

VIOInput offset voltage

V

,

,

Full range

1.7

1.7µV/°C

V

IC

0,

R

S

Ω,

IIOInput offset current

nA

IIBInput bias current

A

15to15.3to15to15.3

V

R

Ω

V

15to15.3to15to15.3

g

V

V

V

g

V

A

gg

V

±10 V

R

2 kΩ

V/mV

CMRR

V

V

min, R

50 Ω

dB

k

ygj

CC±

,

dB

I

V

0

25°C

mA

ICCSupply current

V

No load

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2141I electrical characteristics at specified free-air temperature, V
otherwise noted)

TLE2141I TLE2141AI

MIN TYP MAX MIN TYP MAX

–15 –15.3 –15 –15.3

13 13.2 13 13.2

–15 –15.3 –15 –15.3

12.7 12.9 12.7 12.9

13.7 14 13.7 14

13.1 13.7 13.1 13.7

13.7 13.7

13.6 13.6

–14.5 –14.8 –14.5 –14.8
–13.4 –13.8 –13.4 –13.8
–14.6 –14.6
–14.5 –14.5

–25 –50 –25 –50

20 31 20 31

p

α

r
c

z

OS

†

Full range is –40°C to 105°C.

Temperature coefficient of

VIO

input offset voltage

p

p

Common-mode input

ICR

voltage range

Maximum positive peak

OM+

output voltage swing

Maximum negative peak

OM–

output voltage swing

Large-signal differential

VD

voltage amplification
Input resistance 25°C 65 65

i

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop output

o

impedance
Common-mode

rejection ratio
Supply-voltage rejection V

SVR

ratio (∆V
Short-circuit output

current

pp

CC±

/∆VIO)

A

25°C 200 900 175 500

Full range 1500 1000

= 0

V
VO = 0

= 50

S

IO = –150 µA 13.8 14.1 13.8 14.1
IO = –1.5 mA
IO = –15 mA
IO = –100 µA
IO = –1 mA
IO = –10 mA 13.1 13.1
IO = 150 µA –14.7 –14.9 –14.7 –14.9
IO = 1.5 mA
IO = 15 mA
IO = 100 µA
IO = 1 mA
IO = 10 mA –13.4 –13.4

=

O

f = 1 MHz 25°C 30 30

=

IC

= ±2.5 V to ±15 V,

RS = 50 Ω

=

O

= 0,

O

ICR

,

R

= 50 Ω

50

=

L

=

S

VID = 1 V
VID = –1 V

25°C 7 100 7 100

Full range 200 200

25°C –0.7 –1.5 –0.7 –1.5

Full range –1.7 –1.7

25°C

Full range

25°C

Full range

25°C

Full range

25°C 100 450 100 450

Full range 40 40

25°C 85 108 85 108

Full range 80 80

25°C 90 106 90 106

Full range 85 85

°

25°C 3.5 4.5 3.5 4.5

Full range 4.7 4.7

= ±15 V (unless

CC±

to

to

µ

°

µ

MΩ

Ω

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

23

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

VD

,

L

,

V/µs

tsSettling time

VD

,

s

VnEquivalent input noise voltage

V/√H

V

q

V

InEquivalent input noise current

A/√H

THD

N

O(PP)

,

L

,

0.01%

0.01%

B1Unity-gain bandwidth

R

C

100 pF

66MH

Gain-bandwidth product

L

,

L

,

5.9

5.9

MH

B

g

O(PP)

,

L

,

668

668

kH

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2141I operating characteristics, V

SR+ Positive slew rate
SR– Negative slew rate

p

N(PP)

OM

φ

m

Peak-to-peak equivalent input
noise voltage

p

Total harmonic distortion plus V

+

noise

Maximum output-swing V
bandwidth

Phase margin at unity gain RL = 2 kΩ, CL = 100 pF

p

A

= –1, R

CL = 500 pF
A

= –1,

10-V step
RS = 20 Ω, f = 10 Hz 15 15

RS = 20 Ω, f = 1 kHz 10.5 10.5
f = 0.1 Hz to 1 Hz 0.48 0.48
f = 0.1 Hz to 10 Hz
f = 10 Hz 1.89 1.89
f = 1 kHz 0.47 0.47

AVD = 10,

= 2 kΩ,

L

R

= 2 kΩ, C

f = 100 kHz

AVD = 1,

= ±15 V, TA = 25°C

CC±

= 2 kΩ,

To 0.1% 0.34 0.34
To 0.01% 0.4 0.4

= 20 V, R

= 20 V, R

= 2 kΩ,

f = 10 kHz

=

L

= 100 pF,

= 2 kΩ,

CL = 100 pF

TLE2141I TLE2141AI

MIN TYP MAX MIN TYP MAX

27 45 27 45
27 42 27 42

0.51 0.51

p

58° 58°

µ

n

z

µ

p

z

z

z

z

24

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

VIOInput offset voltage

V

,

,

Full range

1.7

1.7µV/°C

V

O

2.5 V,

R

S

Ω,

IIOInput offset current

nA

IIBInput bias current

A

0to0.3to0to0.3

V

R

Ω

V

0to0.3to0to0.3

g

VOHHigh-level output voltage

V

mV

VOLLow-level output voltage

mV

A

gg

IC

,

L

,

V/mV

CMRR

j

V

V

min,R

50 Ω

dB

k

ygj

CC±

,

dB

ICCSupply current

O

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2142I electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)

TLE2142I TLE2142AI

MIN TYP MAX MIN TYP MAX

µ

°

µ

0 –0.3 0 –0.3

to

3 3.2 3 3.2
0 –0.3 0 –0.3

to

2.7 2.9 2.7 2.9

MΩ

Ω

p

α

r
c

z

†

Full range is – 40°C to 105°C.

Temperature coefficient

VIO

of input offset voltage

p

p

Common-mode input

ICR

voltage range

p

p

Large-signal differential V

VD

voltage amplification
Input resistance 25°C 70 70

i

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop output

o

impedance
Common-mode rejection

ratio
Supply-voltage rejection V

SVR

ratio (∆V

pp

CC±

/∆VIO)

A

25°C 220 1900 220 1500

Full range 2400 2000

= 2.5 V

V
VIC = 2.5 V

= 50

S

IOH = –150 µA 3.9 4.1 3.9 4.1
IOH = –1.5 mA 25°C 3.8 4 3.8 4
IOH = –15 mA 3.4 3.7 3.4 3.7
IOH = 100 µA 3.8 3.8
IOH = 1 mA Full range 3.7 3.7
IOH = 10 mA 3.5 3.5
IOl = 150 µA 75 125 75 125
IOL = 1.5 mA 25°C 150 225 150 225
IOL = 15 mA 1.2 1.4 1.2 1.4 V
IOL = 100 µA 175 175
IOL = 1 mA Full range 225 225
IOL = 10 mA 1.2 1.2 V

= ±2.5 V , R

VO = 1 V to –1.5 V

f = 1 MHz 25°C 30 30

=

IC

ICR

= ±2.5 V to ±15 V,

RS = 50 Ω
VO = 2.5 V, No load,

VIC = 2.5 V

R

= 50 Ω

50

= 2 kΩ,

=

S

25°C 8 100 8 100

Full range 200 200

25°C –0.8 –2 –0.8 –2

Full range –2.2 –2.2

25°C

Full range

25°C 50 220 50 220

Full range 10 10

25°C 85 118 85 118

Full range 80 80

25°C 90 106 90 106

Full range 85 85

25°C 6.6 8.8 6.6 8.8

Full range 9.2 9.2

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

25

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

,

†

,

A

VD

1,

R

L

kΩ ,

V/µs

tsSettling time

VD

,

s

V

q
V/√H

V

i

t

V

I

q
A/√H

†

,

THD

N

V

O

V,

R

L

kΩ ,

0.0052%

0.0052%
†

,

,

Gain-bandwidth product

R

L

kΩ ,

C

L

100 F,

5.8

5.8

MH

,

B

g

V

O(PP)

V,

L

,

660

660

kH

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2142I operating characteristics, VCC = 5 V, TA = 25°C

MIN TYP MAX MIN TYP MAX

SR+ Positive slew rate
SR– Negative slew rate

n

N(PP)

n

B

1

OM

φ

m

†

RL terminates at 2.5 V .

Equivalent input noise
voltage

Peak-to-peak equivalent

p

npu

noise voltage
Equivalent input noise

current
Total harmonic distortion

+

plus noise
Unity-gain bandwidth

Maximum output-swing
bandwidth

Phase margin at unity gain RL = 2 kن, CL = 100 pF

p

A

= –1

CL = 500 pF
A

= –1,

2.5-V step
RS = 20 Ω, f = 10 Hz 15 15

RS = 20 Ω,
f = 0.1 Hz to 1 Hz 0.48 0.48

f = 0.1 Hz to 10 Hz
f = 10 Hz 1.92 1.92

f = 1 kHz
V

= 1 V to 3 V,R

1 V to 3

AVD = 2,
RL = 2 kن,

R

= 2 kΩ

2

f = 100 kHz
V

= 2 V

2

AVD = 1,

R

= 2 kΩ

2

To 0.1% 0.16 0.16
To 0.01% 0.22 0.22

f = 1 kHz 10.5 10.5

= 2 kΩ

2

f = 10 kHz
CL = 100 pF 5.9 5.9 MHz

C

= 100 pF

R

= 2 kن,

CL = 100 pF

TLE2142I TLE2142AI

45 45
42 42

0.51 0.51

0.5 0.5

57° 57°

µ

n

z

µ

p

z

z

z

26

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

VIOInput offset voltage

V

,

,

Full range

1.7

1.7µV/°C

V

IC

0,

R

S

Ω,

IIOInput offset current

nA

IIBInput bias current

A

15to15.3to15to15.3

V

R

Ω

V

15to15.3to15to15.3

g

V

V

V

g

V

A

gg

V

±10 V

R

2 kΩ

V/mV

CMRR

j

dB

k

ygj

CC±

,

dB

IOSShort-circuit output current

V

0

25°C

mA

ICCSupply current

V

No load

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2142I electrical characteristics at specified free-air temperature, V
otherwise noted)

TLE2142I TLE2142I

MIN TYP MAX MIN TYP MAX

–15 –15.3 –15 –15.3

13 13.2 13 13.2

–15 –15.3 –15 –15.3

12.7 12.9 12.7 12.9

13.7 14 13.7 14

13.3 13.7 13.3 13.7

13.7 13.7

13.6 13.6

–14.5 –14.8 –14.5 –14.8
–13.4 –13.8 –13.4 –13.8
–14.6 –14.6
–14.5 –14.5

–25 –50 –25 –50

20 31 20 31

p

α

r
c

z

†

Full range is –40°C to 105°C.

Temperature coefficient of

VIO

input offset voltage

p

p

Common-mode input

ICR

voltage range

Maximum positive peak

OM+

output voltage swing

Maximum negative peak

OM–

output voltage swing

Large-signal differential

VD

voltage amplification
Input resistance 25°C 65 65

i

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop output imped-

o

ance
Common-mode rejection

ratio
Supply-voltage rejection V

SVR

ratio (∆V

pp

CC±

/∆VIO)

A

25°C 290 1200 275 750

Full range 1800 1400

= 0

V
VO = 0

= 50

S

IO = –150 µA 13.8 14.1 13.8 14.1
IO = –1.5 mA
IO = –15 mA
IO = –100 µA
IO = –1 mA
IO = –10 mA 13.3 13.3
IO = 150 µA –14.7 –14.9 –14.7 –14.9
IO = 1.5 mA
IO = 15 mA
IO = 100 µA
IO = 1 mA
IO = 10 mA –13.4 –13.4

=

O

f = 1 MHz 25°C 30 30
VIC = V

RS = 50 Ω

= ±2.5 V to ±15 V,

RS = 50 Ω

p

O

O

=

= 0,

R

= 50 Ω

50

25°C 7 100 7 100

Full range 200 200

25°C –0.7 –1.5 –0.7 –1.5

Full range –1.7 –1.7

25°C

Full range

25°C

Full range

25°C

Full range

,

=

L

min 25°C 85 108 85 108

ICR

VID = 1 V
VID = –1 V

25°C 100 450 100 450

Full range 40 40

Full range 80 80

25°C 90 106 90 106

Full range 85 85

°

25°C 6.9 9 6.9 9

Full range 9.4 9.4

= ±15 V (unless

CC±

to

to

µ

°

µ

MΩ

Ω

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

27

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

VD

,

L

,

V/µs

tsSettling time

VD

,

s

VnEquivalent input noise voltage

V/√H

V

q

V

InEquivalent input noise current

A/√H

THD

N

O(PP)

,

L

,

0.01%

0.01%

Gain-bandwidth product

L

,

L

,

5.9

5.9

MH

B

g

O(PP)

,

L

,

668

668

kH

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2142I operating characteristics, V

SR+ Positive slew rate
SR– Negative slew rate

p

N(PP)

B

1

OM

φ

m

Peak-to-peak equivalent input
noise voltage

p

Total harmonic distortion plus V

+

noise
Unity-gain bandwidth RL = 2 kΩ, CL = 100 pF 6 6 MHz

Maximum output-swing V
bandwidth

Phase margin at unity gain RL = 2 kΩ, CL = 100 pF

p

A

= –1, R

CL = 500 pF
A

= –1,

10-V step
RS = 20 Ω, f = 10 Hz 15 15

RS = 20 Ω, f = 1 kHz 10.5 10.5
f = 0.1 Hz to 1 Hz 0.48 0.48
f = 0.1 Hz to 10 Hz
f = 10 Hz 1.89 1.89
f = 1 kHz 0.47 0.47

AVD = 10,

R

= 2 kΩ, C

f =100 kHz

AVD = 1,

= ±15 V, TA = 25°C

CC±

= 2 kΩ,

To 0.1% 0.34 0.34
To 0.01% 0.4 0.4

= 20 V, R

= 20 V, R

= 2 kΩ,

f = 10 kHz

= 100 pF,

= 2 kΩ,

CL = 100 pF

TLE2142I TLE2142AI

MIN TYP MAX MIN TYP MAX

30 45 30 45
30 42 30 42

0.51 0.51

58° 58°

µ

n

z

µ

p

z

z

z

28

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

V

I

t offset

mV

,

Full range

1.7

1.7µV/°C

V

IC

0,

R

S

IIOInput offset current

nA

IIBInput bias current

A

V

R

Ω

V

g

V

g

V

mV

V

mV

A

gg

IC

,

L

,

V/mV

CMRR

V

V

min,R

50 Ω

dB

k

rejection ratio

CC±

,

dB

ICCSupply current

O

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2144I electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)

TLE2144I TLE2144AI

MIN TYP MAX MIN TYP MAX

°

8 100 8 100

µ

0 –0.3 0 –0.3

to to to to

3 3.2 3 3.2
0 –0.3 0 –0.3

to to to to

2.7 2.9 2.7 2.9

3.4 3.7 3.4 3.7

3.8 3.8

1.2 1.6 1.2 1.6 V
175 175

p

npu

IO

α

r
c

z

†

Full range is –40°C to 105°C.

Temperature coefficient

VIO

of input offset voltage

p

p

Common-mode input

ICR

voltage range

High-level

OH

output voltage

Low-level

OL

output voltage

Large-signal differential V

VD

voltage amplification
Input resistance 25°C 70 70 MΩ

i

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop output

o

impedance
Common-mode

rejection ratio
Supply-voltage

SVR

(∆V

pp

CC±

voltage

/∆VIO)

A

25°C 0.5 3.8 0.5 3

Full range 4.8 4

= 0

V
VO = 0

= 50

S

IOH = –150 µA 3.9 4.1 3.9 4.1
IOH = –1.5 mA 25°C 3.8 4 3.8 4
IOH = –15 mA
IOH = 100 µA
IOH = 1 mA Full range 3.7 3.7
IOH = 10 mA 3.5 3.5
IOL = 150 µA 75 125 75 125
IOL = 1.5 µA 25°C 150 225 150 225
IOL = 15 mA
IOL = 100 µA
IOL = 1 mA Full range 225 225
IOL = 10 mA 1.4 1.4 V

= ±2.5 V , R

VO = 1 V to –1.5 V

f = 1 MHz 25°C 30 30 Ω

=

IC

ICR

V

= ±2.5 V to ±15 V,

RS = 50 Ω

VO = 2.5 V, No load,
VIC = 2.5 V

R

= 50 Ω,

50 Ω,

= 2 kΩ,

=

S

25°C

Full range 200 200

25°C –0.8 –2 –0.8 –2

Full range –2.2 –2.2

25°C

Full range

25°C 50 95 50 95

Full range 10 10

25°C 85 118 85 118

Full range 80 80

25°C 90 106 90 106

Full range 85 85

25°C 13.2 17.6 13.2 17.6

Full range 18.4 18.4

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

29

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

†

,

VD

,

R

L

kΩ ,

V/µs

tsSettling time

VD

,

s

VnEquivalent input noise voltage

V/√H

V

q

V

InEquivalent input noise current

A/√H

THD

N

O

,

L

,

0.0052%

0.0052%

Gain-bandwidth product

L

,

L

,

5.8

5.8

MH

B

g

O(PP)

,

L

,

660

660

kH

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2144I operating characteristics, VCC = 5 V, TA = 25°C

SR+ Positive slew rate
SR– Negative slew rate

p

N(PP)

B

1

OM

φ

m

†

RL terminates at 2.5 V

Peak-to-peak equivalent input
noise voltage

p

Total harmonic distortion plus V

+

noise
Unity-gain bandwidth

Maximum output-swing
bandwidth

Phase margin at unity gain

p

A

= –1,

CL = 500 pF
A

= –1,

2.5-V step
RS = 20 Ω, f = 10 Hz 15 15

RS = 20 Ω, f = 1 kHz 10.5 10.5
f = 0.1 Hz to 1 Hz 0.48 0.48
f = 0.1 Hz to 10 Hz
f = 10 Hz 1.92 1.92
f = 10 kHz 0.5 0.5

= 1 V to 3 V,

AVD = 2,
RL = 2 kن,
R

= 2 kن,

f = 100 kHz
V

= 2 V,

AVD = 1,
RL = 2 kن,

R

= 2 kΩ

2

To 0.1% 0.16 0.16
To 0.01% 0.22 0.22

R

= 2 kن,

f = 10 kHz
CL = 100 pF 5.9 5.9 MHz
C

= 100 pF,

R

= 2 kن,

CL = 100 pF
CL = 100 pF

TLE2144I TLE2144AI

MIN TYP MAX MIN TYP MAX

45 45
42 42

0.51 0.51

57° 57°

µ

n

z

µ

p

z

z

z

30

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

V

I

t offset

mV

,

Full range

1.7

1.7µV/°C

V

IC

0,

R

S

IIOInput offset current

nA

IIBInput bias current

A

V

R

Ω

V

g

V

V

V

peak output voltage

g

V

swing

A

gg

V

±10 V

R

2 kΩ

V/mV

CMRR

V

V

min

R

50 Ω

dB

k

rejection ratio

CC±

,

dB

I

V

0

25°C

mA

ICCSupply current

V

No load

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2144I electrical characteristics at specified free-air temperature, V
otherwise noted)

TLE2144I TLE2144AI

MIN TYP MAX MIN TYP MAX

7 100 7 100

–15 –15.3 –15 –15.3

to to to to

13 13.2 13 13.2

–15 –15.3 –15 –15.3

to to to to

12.7 12.9 12.7 12.9

13.7 14 13.7 14

13.1 13.7 13.1 13.7

13.7 13.7

13.6 13.6

–14.5 –14.8 –14.5 –14.8

–14.5 –14.5

–25 –50 –25 –50

20 31 20 31

p

npu

IO

α

r
c

z

OS

†

Full range is –40°C to 105°C.

Temperature coefficient

VIO

of input offset voltage

p

p

Common-mode input

ICR

voltage range

Maximum positive peak

OM+

output voltage swing

Maximum negative
p

OM–

swin

Large-signal differential

VD

voltage amplification
Input resistance 25°C 65 65 MΩ

i

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop

o

output impedance
Common-mode

rejection ratio
Supply-voltage

SVR

(∆V
Short-circuit output

current

pp

CC±

voltage

p

/∆VIO)

A

25°C 0.6 2.4 0.5 1.5

Full range 3.2 2.8

= 0

V
VO = 0

= 50

S

IO = –150 µA 13.8 14.1 13.8 14.1
IO = –1.5 mA
IO = –15 mA
IO = –100 µA
IO = –1 mA
IO = –10 mA 13.1 13.1
IO = 150 µA –14.7 –14.9 –14.7 –14.9
IO = 1.5 mA
IO = 15 mA –13.4 –13.8 –13.4 –13.8
IO = 100 µA –14.6 –14.6
IO = 1 mA
IO = 10 mA –13.4 –13.4

=

O

f = 1 MHz 25°C 30 30 Ω

=

IC

ICR

V

= ±2.5 V to ±15 V,

RS = 50 Ω

=

O

= 0,

O

,

,

R

= 50 Ω,

50 Ω,

=

L

=

S

VID = 1 V
VID = –1 V

25°C

Full range 200 200

25°C –0.7 –1.5 –0.7 –1.5

Full range –1.7 –1.7

25°C

Full range

25°C

Full range

25°C

Full range

25°C 100 170 100 170

Full range 40 40

25°C 85 108 85 108

Full range 80 80

25°C 90 106 90 106

Full range 85 85

°

25°C 13.8 18 13.8 18

Full range 18.8 18.8

= ±15 V (unless

CC±

°

µ

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

31

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

VD

,

L

,

V/µs

tsSettling time

VD

,

s

V

q
V/√H

V

q

V

I

q
A/√H

THD

N

O(PP)

,

L

,

0.01%

0.01%

Gain-bandwidth product

L

,

L

,

5.9

5.9

MH

B

g

O(PP)

,

L

,

668

668

kH

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2144I operating characteristics, V

SR+ Positive slew rate
SR– Negative slew rate

n

N(PP)

n

B

1

OM

φ

m

Equivalent input
noise voltage

Peak-to-peak equivalent
input noise voltage

Equivalent input
noise current

Total harmonic distortion plus V

+

noise
Unity-gain bandwidth RL = 2 kΩ, CL = 100 pF 6 6 MHz

Maximum output-swing V
bandwidth

Phase margin at unity gain RL = 2 kΩ, CL = 100 pF 58° 58°

p

A

= –1, R

CL = 500 pF
A

= –1,

10-V step
RS = 20 Ω, f = 10 Hz 15 15

RS = 20 Ω,
f = 0.1 Hz to 1 Hz 0.48 0.48
f = 0.1 Hz to 10 Hz
f = 10 Hz 1.89 1.89
f = 1 kHz

AVD = 10,

R

= 2 kΩ, C

f = 100 kHz

AVD = 1,

= ±15 V, TA = 25°C

CC±

= 2 kΩ,

To 0.1% 0.34 0.34
To 0.01% 0.4 0.4

f = 1 kHz 10.5 10.5

= 20 V, R

= 20 V, R

= 2 kΩ,

f = 10 kHz

= 100 pF,

= 2 kΩ,

CL = 100 pF

TLE2144I TLE2144AI

MIN TYP MAX MIN TYP MAX

27 45 27 45
27 42 27 42

0.51 0.51

0.47 0.47

µ

n

z

µ

p

z

z

z

32

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

VIOInput offset voltage

V

,

Full range

1.7

1.7µV/°C

V

O

2.5 V

R

S

Ω,

IIOInput offset current

nA

IIBInput bias current

A

0to0.3to0to0.3

V

R

Ω

V

0to0.3to0to0.3

g

V

g

V

mV

V

mV

A

gg

IC

,

L

,

V/mV

CMRR

V

V

min, R

50 Ω

dB

k

ygj

CC±

,

dB

ICCSupply current

O

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2141M electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)

TLE2141M TLE2141AM

MIN TYP MAX MIN TYP MAX

µ

°

µ

0 –0.3 0 –0.3

to

3 3.2 3 3.2
0 –0.3 0 –0.3

to

2.7 2.9 2.7 2.9

3.8 4 3.8 4

3.2 3.7 3.2 3.7

3.75 3.75

3.65 3.65

150 225 150 225

1.2 1.4 1.2 1.4 V
200 200
250 225

MΩ

Ω

p

α

r
c

z

†

Full range is –55°C to 125°C.

Temperature coefficient

VIO

of input offset voltage

p

p

Common-mode input

ICR

voltage range

High-level output

OH

voltage

Low-level output

OL

voltage

Large-signal differential V

VD

voltage amplification
Input resistance 25°C 70 70

i

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop

o

output impedance
Common-mode

rejection ratio
Supply-voltage rejection V

SVR

ratio (∆V

pp

CC±

/∆VIO)

A

25°C 225 1400 200 1000

Full range 2100 1700

= 2.5 V R

V
VIC = 2.5 V

= 50

S

IOH = –150 µA 3.9 4.1 3.9 4.1
IOH = –1.5 mA
IOH = –15 mA
IOH = –100 µA
IOH = –1 mA
IOH = –10 mA 3.25 3.25
IOL = 150 µA 75 125 75 125
IOL = 1.5 µA
IOL = 15 mA
IOL = 100 µA
IOL = 1 mA
IOL = 10 mA 1.25 1.25 V

= ±2.5 V , R

VO = 1 V to –1.5 V

f = 1 MHz 25°C 30 30

=

IC

ICR

= ±2.5 V to ±15 V,

RS = 50 Ω
VO = 2.5 V, No load,

VIC = 2.5 V

= 50 Ω

50

= 2 kΩ,

=

S

25°C 8 100 8 100

Full range 250 250

25°C –0.8 –2 –0.8 –2

Full range –2.3 –2.3

25°C

Full range

25°C

Full range

25°C

Full range

25°C 50 220 50 220

Full range 5 5

25°C 85 118 85 118

Full range 80 80

25°C 90 106 90 106

Full range 85 85

25°C 3.4 4.4 3.4 4.4

Full range 4.6 4.6

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

33

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

,

†

,

A

VD

1,

R

L

kΩ ,

V/µs

tsSettling time

VD

,

s

VnEquivalent input noise voltage

V/√H

V

q

V

InEquivalent input noise current

A/√H

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2141M operating characteristics, VCC = 5 V, TA = 25°C

MIN TYP MAX MIN TYP MAX

SR+ Positive slew rate
SR– Negative slew rate

p

N(PP)

THD + N
B

1

B

OM

φ

m

†

RL and CL terminated to 2.5 V .

Peak-to-peak equivalent input
noise voltage

p

Total harmonic distortion
plus noise

Unity-gain bandwidth RL = 2 kن, CL = 100 pF
Gain-bandwidth product
Maximum output-swing

bandwidth
Phase margin at unity gain RL = 2 kن, CL = 100 pF

A

= –1

CL = 500 pF
A

= –1,

2.5-V step
RS = 20 Ω, f = 10 Hz 15 15

RS = 20 Ω, f = 1 kHz 10.5 10.5
f = 0.1 Hz to 1 Hz 0.48 0.48
f = 0.1 Hz to 10 Hz
f = 10 Hz 1.92 1.92
f = 1 kHz 0.5 0.5
VO = 1 V to 3 V,

AVD = 2,

RL = 2 kن,
f = 100 kHz

V

= 2 V,

O(PP)

AVD = 1

R

= 2 kΩ

2

To 0.1% 0.16 0.16
To 0.01% 0.22 0.22

RL = 2 kن,
f = 10 kHz

†

CL = 100 pF†,

RL = 2 kن,

†

TLE2141M TLE2141AM

45 45
42 42

0.51 0.51

0.0052% 0.0052%

5.9 5.9 MHz

5.8 5.8 MHz

660 660 kHz

57° 57°

µ

n

z

µ

p

z

34

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

VIOInput offset voltage

V

Full range

1.7

1.7µV/°C

V

R

50 Ω

IIOInput offset current

nA

IIBInput bias current

A

15to15.3to15to15.3

V

R

Ω

V

15to15.3to15to15.3

g

V

V

V

g

V

A

gg

V

±10 V

R

2 kΩ

V/mV

CMRR

V

V

min

R

50 Ω

dB

k

ygj

CC±

,

dB

I

V

0

25°C

mA

ICCSupply current

O

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2141M electrical characteristics at specified free-air temperature, V
otherwise noted)

TLE2141M TLE2141AM

MIN TYP MAX MIN TYP MAX

–15 –15.3 –15 –15.3

13 13.2 13 13.2

–15 –15.3 –15 –15.3

12.7 12.9 12.7 12.9

13.7 14 13.7 14

13.1 13.7 13.1 13.7

13.7 13.7

13.6 13.6

–14.5 –14.8 –14.5 –14.8
–13.4 –13.8 –13.4 –13.8
–14.6 –14.6
–14.5 –14.5

–25 –50 –25 –50

20 31 20 31

p

α

r
c

z

OS

†

Full range is –55°C to 125°C.

Temperature coefficient

VIO

of input offset voltage

p

p

Common-mode input

ICR

voltage range

Maximum positive peak

OM+

output voltage swing

Maximum negative peak

OM–

output voltage swing

Large-signal differential

VD

voltage amplification
Input resistance 25°C 65 65

i

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop output

o

impedance
Common-mode

rejection ratio
Supply-voltage rejection V

SVR

ratio (∆V
Short-circuit output

current

pp

CC±

/∆VIO)

A

25°C 200 900 175 500

Full range 1700 1200

= 0,

IC

= 50

S

IO = –150 µA 13.8 14.1 13.8 14.1
IO = –1.5 mA
IO = –15 mA
IO = –100 µA
IO = –1 mA
IO = –10 mA 13.1 13.1
IO = 150 µA –14.7 –14.9 –14.7 –14.9
IO = 1.5 mA
IO = 15 mA
IO = 100 µA
IO = 1 mA
IO = 10 mA –13.4 –13.4

=

O

f = 1 MHz 25°C 30 30

IC

RS = 50 Ω

=

O

VO = 0, No load,
VIC = 2.5 V

,

=

ICR

= ±2.5 V to ±15 V,

=

S

=

L

,

=

S

VID = 1 V
VID = –1 V

25°C 7 100 7 100

Full range 250 250

25°C –0.7 –1.5 –0.7 –1.5

Full range –1.8 –1.8

25°C

Full range

25°C

Full range

25°C

Full range

25°C 100 450 100 450

Full range 20 20

25°C 85 108 85 108

Full range 80 80

25°C 90 106 90 106

Full range 85 85

°

25°C 3.5 4.5 3.5 4.5

Full range 4.7 4.7

= ±15 V (unless

CC±

to

to

µ

°

µ

MΩ

Ω

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

35

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

VD

,

L

,

V/µs

tsSettling time

VD

,

s

VnEquivalent input noise voltage

V/√H

V

q

V

InEquivalent input noise current

A/√H

THD

N

O(PP)

,

L

,

0.01%

0.01%
B1Unity-gain bandwidth

R

C

100 pF

66MH

Gain-bandwidth product

L

,

L

,

5.9

5.9

MH

B

g

O(PP)

,

L

,

668

668

kH

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2141M operating characteristics, V

SR+ Positive slew rate
SR– Negative slew rate

p

N(PP)

OM

φ

m

Peak-to-peak equivalent input
noise voltage

p

Total harmonic distortion plus V

+

noise

Maximum output-swing V
bandwidth

Phase margin at unity gain RL = 2 kΩ, CL = 100 pF

p

A

= –1, R

CL = 100 pF
A

= –1,

10-V step
RS = 20 Ω, f = 10 Hz 15 15

RS = 20 Ω, f = 1 kHz 10.5 10.5
f = 0.1 Hz to 1 Hz 0.48 0.48
f = 0.1 Hz to 10 Hz
f = 10 Hz 1.89 1.89
f = 1 kHz 0.47 0.47

AVD = 10,

= 2 kΩ,

L

R

= 2 kΩ, C

f = 100 kHz

AVD = 1,

= ±15 V, TA = 25°C

CC±

= 2 kΩ,

To 0.1% 0.34 0.34
To 0.01% 0.4 0.4

= 20 V, R

= 20 V, R

= 2 kΩ,

f = 10 kHz

=

L

= 100 pF,

= 2 kΩ,

CL = 100 pF

TLE2141M TLE2141AM

MIN TYP MAX MIN TYP MAX

27 45 27 45
27 42 27 42

0.51 0.51

p

58° 58°

µ

n

z

µ

p

z

z

z

z

36

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

VIOInput offset voltage

V

,

,

Full range

1.7

1.7µV/°C

V

O

2.5 V,

R

S

Ω,

IIOInput offset current

nA

IIBInput bias current

A

0to0.3to0to0.3

V

R

Ω

V

0to0.3to0to0.3

g

V

g

V

mV

V

mV

A

gg

IC

,

L

,

V/mV

CMRR

V

V

min,R

50 Ω

dB

k

ygj

CC±

,

dB

ICCSupply current

O

,

,

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2142M electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)

TLE2142M TLE2142AM

MIN TYP MAX MIN TYP MAX

µ

°

µ

0 –0.3 0 –0.3

to

3 3.2 3 3.2
0 –0.3 0 –0.3

to

2.7 2.9 2.7 2.9

3.8 4 3.8 4

3.4 3.7 3.4 3.7

3.75 3.75

3.65 3.65

150 225 150 225

1.2 1.4 1.2 1.4 V
200 200
250 250

MΩ

Ω

p

α

r
c

z

†

Full range is – 55°C to 125°C.

Temperature coefficient

VIO

of input offset voltage

p

p

Common-mode input

ICR

voltage range

High-level output

OH

voltage

Low-level output

OL

voltage

Large-signal differential V

VD

voltage amplification
Input resistance 25°C 70 70

i

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop output

o

impedance
Common-mode

rejection ratio
Supply-voltage rejec- V

SVR

tion ratio (∆V

pp

CC±

/∆VIO)

A

25°C 220 1900 200 1500

Full range 2600 2200

= 2.5 V

V
VIC = 2.5 V

= 50

S

IOH = –150 µA 3.9 4.1 3.9 4.1
IOH = –1.5 mA
IOH = –15 mA
IOH = 100 µA
IOH = 1 mA
IOH = 10 mA 3.45 3.45
IOL = 150 µA 75 125 75 125
IOL = 1.5 mA
IOL = 15 mA
IOL = 100 µA
IOL = 1 mA
IOL = 10 mA 1.25 1.25 V

= ±2.5 V , R

VO = 1 V to –1.5 V

f = 1 MHz 25 °C 30 30

=

IC

ICR

= ±2.5 V to ±15 V,

RS = 50 Ω
V

= 2.5 V, No load,

VIC = 2.5 V

R

S

= 50 Ω

50

= 2 kΩ,

=

25°C 8 100 8 100

Full range 200 200

25°C –0.8 –2 –0.8 –2

Full range –2.3 –2.3

25°C

Full range

25°C

Full range

25°C

Full range

25°C 50 220 50 220

Full range 5 5

25°C 85 118 85 118

Full range 80 80

25°C 90 106 90 106

Full range 85 85

25°C 6.6 8.8 6.6 8.8

Full range 9.2 9.2

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

37

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

,

†

,

A

VD

1,

R

L

kΩ ,

V/µs

tsSettling time

VD

,

s

V

q
V/√H

V

q

V

I

q
A/√H

†

,

THD

N

O

,

R

L

kΩ ,

0.0052%

0.0052%
†

,

Gain-bandwidth product

R

L

kΩ ,

C

L

100 F

5.8

5.8

MH

,

B

g

V

O(PP)

V,

L

,

660

660

kH

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2142M operating characteristics, VCC = 5 V, TA = 25°C

MIN TYP MAX MIN TYP MAX

SR+ Positive slew rate
SR– Negative slew rate

n

N(PP)

n

B

1

OM

φ

m

†

RL terminates at 2.5 V .

Equivalent input noise volt­age

Peak-to-peak equivalent
input noise voltage

Equivalent input noise cur­rent

Total harmonic distortion V

+

plus noise
Unity-gain bandwidth

Maximum output-swing
bandwidth

Phase margin RL = 2 kن, CL = 100 pF

p

A

= –1

CL = 500 pF
A

= –1,

2.5-V step
RS = 20 Ω, f = 10 Hz 15 15

RS = 20 Ω,
f = 0.1 Hz to 1 Hz 0.48 0.48
f = 0.1 Hz to 10 Hz
f = 10 Hz 1.92 1.92
f = 1 kHz

= 1 V to 3 V,

AVD = 2,
RL = 2 kن,
R

= 2 kΩ

2

f = 100 kHz
V

= 2 V

2

AVD = 1,

R

= 2 kΩ

2

To 0.1% 0.16 0.16
To 0.01% 0.22 0.22

f = 1 kHz 10.5 10.5

R

= 2 kΩ

2

f = 10 kHz
CL = 100 pF 5.9 5.9 MHz

C

= 100 pF

R

= 2 kن,

CL = 100 pF

TLE2142M TLE2142AM

45 45
42 42

0.51 0.51

0.5 0.5

57° 57°

µ

n

z

µ

p

z

z

z

38

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

VIOInput offset voltage

V

Full range

1.7

1.7µV/°C

V

0

R

50 Ω

IIOInput offset current

nA

IIBInput bias current

A

15to15.3to15to15.3

V

R

Ω

V

15to15.3to15to15.3

g

V

V

V

g

V

A

gg

V

±10 V

R

kΩ

V/mV

CMRR

j

IC ICR

,

dB

k

ygj

CC±

,

dB

IOSShort-circuit output current

V

0

25°C

mA

ICCSupply current

O

,

,

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2142M electrical characteristics at specified free-air temperature, V
otherwise noted)

TLE2142M TLE2142AM

MIN TYP MAX MIN TYP MAX

–15 –15.3 –15 –15.3

13 13.2 13 13.2

–15 –15.3 –15 –15.3

12.7 12.9 12.7 12.9

13.7 14 13.7 14

13.3 13.7 13.3 13.7

13.7 13.7

13.6 13.6

–14.5 –14.8 –14.5 –14.8
–13.4 –13.8 –13.4 –13.8
–14.6 –14.6
–14.5 –14.5

–25 –50 –25 –50

20 31 20 31

p

α

r
c

z

†

Full range is –55°C to 125°C.

Temperature coefficient of

VIO

input offset voltage

p

p

Common-mode input

ICR

voltage range

Maximum positive peak

OM+

output voltage swing

Maximum negative peak

OM–

output voltage swing

Large-signal differential

VD

voltage amplification
Input resistance 25°C 65 65

i

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop output

o

impedance
Common-mode rejection V

ratio
Supply-voltage rejection V

SVR

ratio (∆V

pp

CC ±

/∆VIO)

A

25°C 290 1200 275 750

Full range 2000 1600

,

=

IC

= 50

S

IO = –150 µA 13.8 14.1 13.8 14.1
IO = –1.5 mA
IO = –15 mA
IO = –100 µA
IO = –1 mA
IO = –10 mA 13.3 13.3
IO = 150 µA –14.7 –14.9 –14.7 –14.9
IO = 1.5 mA
IO = 15 mA
IO = 100 µA
IO = 1 mA
IO = 10 mA –13.4 –13.4

=

O

f = 1 MHz 25°C 30 30

= V

RS = 50 Ω

= ±2.5 V to ±15 V,

RS = 50 Ω

p

=

O

V

= 0, No load,

VIC = 2.5 V

S

,

L

min,

VID = 1 V
VID = –1 V

=

= 2

25°C 7 100 7 100

Full range 250 250

25°C –0.7 –1.5 –0.7 –1.5

Full range –1.8 –1.8

25°C

Full range

25°C

Full range

25°C

Full range

25°C 100 450 100 450

Full range 20 20

25°C 85 108 85 108

Full range 80 80

25°C 90 106 90 106

Full range 85 85

°

25°C 6.9 9 6.9 9

Full range 9.4 9.4

= ±15 V (unless

CC±

to

to

µ

°

µ

MΩ

Ω

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

39

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

L

,

VD

,

V/µs

tsSettling time

VD

,

s

VnEquivalent input noise voltage

V/√H

V

q

V

InEquivalent input noise current

A/√H

THD

N

O(PP)

,

L

,

0.01%

0.01%

Gain-bandwidth product

L

,

L

,

5.9

5.9

MH

B

g

O(PP)

,

L

,

668

668

kH

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2142M operating characteristics, V

SR+ Positive slew rate
SR– Negative slew rate

p

N(PP)

B

1

OM

φ

m

Peak-to-peak equivalent input
noise voltage

p

Total harmonic distortion plus V

+

noise
Unity-gain bandwidth RL = 2 kΩ, CL = 100 pF 6 6 MHz

Maximum output-swing band- V
width

Phase margin at unity gain RL = 2 kΩ, CL = 100 pF 58° 58°

p

R

= 2 kΩ, A

CL = 100 pF
A

= –1,

10-V step
RS = 20 Ω, f = 10 Hz 15 15

RS = 20 Ω, f = 1 kHz 10.5 10.5
f = 0.1 Hz to 1 Hz 0.48 0.48
f = 0.1 Hz to 10 Hz
f = 10 Hz 1.89 1.89
f = 1 kHz 0.47 0.47

AVD = 10,

R

= 2 kΩ, C

f = 100 kHz

AVD = 1,

= ±15 V, T

CC±

= 20 V, R

= 20 V, R

= 25°C

A

TLE2142M TLE2142AM

MIN TYP MAX MIN TYP MAX

= –1,

To 0.1% 0.34 0.34
To 0.01% 0.4 0.4

= 2 kΩ,

f = 10 kHz

= 100 pF,

= 2 kΩ,

CL = 100 pF

27 45 27 45
27 42 27 42

0.51 0.51

µ

n

z

µ

p

z

z

z

40

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

V

I

t offset

mV

,

,

Full range

1.7

1.7µV/°C

V

O

2.5 V,

R

S

Ω,

IIOInput offset current

nA

IIBInput bias current

A

V

R

Ω

V

g

V

g

V

mV

V

mV

A

gg

IC

,

L

,

V/mV

CMRR

V

V

min

R

50 Ω

dB

k

rejection ratio

CC±

,

dB

ICCSupply current

O

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2144M electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)

TLE2144M TLE2144AM

MIN TYP MAX MIN TYP MAX

°

µ

0 –0.3 0 –0.3

to to to to

3 3.2 3 3.2
0 –0.3 0 –0.3

to to to to

2.7 2.9 2.7 2.9

3.4 3.7 3.4 3.7

3.75 3.75

1.2 1.6 1.2 1.6 V
200 200

p

npu

IO

α

r
c

z

†

Full range is –55°C to 125°C.

Temperature coefficient

VIO

of input offset voltage

p

p

Common-mode input

ICR

voltage range

High-level output

OH

voltage

Low-level output

OL

voltage

Large-signal differential V

VD

voltage amplification
Input resistance 25°C 70 70 MΩ

i

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop output

o

impedance
Common-mode

rejection ratio
Supply-voltage

SVR

(∆V

pp

CC±

voltage

/∆VIO)

A

25°C 0.5 3.8 0.5 3

Full range 5.2 4.4

= 2.5 V

V
VIC = 2.5 V

= 50

S

IOH = –150 µA 3.9 4.1 3.9 4.1
IOH = –1.5 mA 25°C 3.8 4 3.8 4
IOH = –15 mA
IOH = 100 µA
IOH = 1 mA Full range 3.65 3.65
IOH = 10 mA 3.45 3.45
IOL = 150 µA 75 125 75 125
IOL = 1.5 µA 25°C 150 225 150 225
IOL = 15 mA
IOL = 100 µA
IOL = 1 mA Full range 250 250
IOL = 10 mA 1.45 1.45 V

= ±2.5 V , R

VO = 1 V to –1.5 V

f = 1 MHz 25°C 30 30 Ω

=

IC

ICR

V

= ±2.5 V to ±15 V,

RS = 50 Ω

VO = 2.5 V, No load,
VIC = 2.5 V

R

= 50 Ω

50

25°C 8 100 8 100

Full range 250 250

25°C –0.8 –2 –0.8 –2

Full range –2.3 –2.3

25°C

Full range

= 2 kΩ,

,

=

S

25°C 50 95 50 95

Full range 5 5

25°C 85 118 85 118

Full range 80 80

25°C 90 106 90 106

Full range 85 85

25°C 13.2 17.6 13.2 17.6

Full range 18.4 18.4

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

41

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

VD

,

L

,

V/µs

tsSettling time

VD

,

s

VnEquivalent input noise voltage

V/√H

V

q

V

InEquivalent input noise current

A/√H

THD

N

O

,

L

,

0.0052%

0.0052%

B1Unity-gain bandwidth

R

kΩ

†

C

100 pF

5.9

5.9

MH

Gain-bandwidth product

L

,

L

,

5.8

5.8

MH

B

g

O(PP)

,

L

,

660

660

kH

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2144M operating characteristics, VCC = 5 V, TA = 25°C

SR+ Positive slew rate
SR– Negative slew rate

p

N(PP)

OM

φ

m

†

RL terminates at 2.5 V

Peak-to-peak equivalent input
noise voltage

p

Total harmonic distortion plus V

+

noise

Maximum output-swing
bandwidth

Phase margin

p

A

= –1,

CL = 500 pF
A

= –1,

2.5-V step
RS = 20 Ω, f = 10 Hz 15 15

RS = 20 Ω, f = 1 kHz 10.5 10.5
f = 0.1 Hz to 1 Hz 0.48 0.48
f = 0.1 Hz to 10 Hz
f = 10 Hz 1.92 1.92
f = 1 kHz 0.5 0.5

= 1 V to 3 V,

AVD = 2,

= 2

L

R

= 2 kن,

f = 100 kHz
V

= 2 V,

AVD = 1
RL = 2 kن,

R

= 2 kن,

To 0.1% 0.16 0.16
To 0.01% 0.22 0.22

R

= 2 kن,

f = 10 kHz

p

,

=

L

C

= 100 pF,

R

= 2 kن,

CL = 100 pF 57° 57°

TLE2144M TLE2144AM

MIN TYP MAX MIN TYP MAX

45 45
42 42

0.51 0.51

µ

n

z

µ

p

z

z

z

z

42

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

T

†

UNIT

V

I

t offset

mV

Full range

1.7

1.7µV/°C

V

0

R

50 Ω

IIOInput offset current

nA

IIBInput bias current

A

V

R

Ω

V

g

V

V

V

V

peak output voltage

g

swing

A

gg

V

±10 V

R

kΩ

V/mV

CMRR

V

V

min

R

50 Ω

dB

k

rejection ratio

CC±

,

dB

I

V

0

25°C

mA

ICCSupply current

O

,

,

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2144M electrical characteristics at specified free-air temperature, V
otherwise noted)

TLE2144M TLE2144AM

MIN TYP MAX MIN TYP MAX

–15 –15.3 –15 –15.3

to to to to

13 13.2 13 13.2

–15 –15.3 –15 –15.3

to to to to

12.7 12.9 12.7 12.9

13.7 14 13.7 14

13.1 13.7 13.1 13.7

13.7 13.7

13.6 13.6

–14.5 –14.8 –14.5 –14.8

–14.5 –14.5

–25 –50 –25 –50

20 31 20 31

p

npu

IO

α

r
c

z

OS

†

Full range is –55°C to 125°C

Temperature coefficient

VIO

of input offset voltage

p

p

Common-mode input

ICR

voltage range

Maximum positive peak

OM+

output voltage swing

Maximum negative
p

OM–

swin

Large-signal differential

VD

voltage amplification
Input resistance 25°C 65 65 MΩ

i

Input capacitance 25°C 2.5 2.5 pF

i

Open-loop output

o

impedance
Common-mode

rejection ratio
Supply-voltage

SVR

(∆V
Short-circuit output

current

pp

CC±

voltage

p

/∆VIO)

A

25°C 0.6 2.4 0.5 1.5

Full range 4 3.2

,

=

IC

= 50

S

IO = –150 µA 13.8 14.1 13.8 14.1
IO = –1.5 mA
IO = –15 mA
IO = –100 µA
IO = –1 mA
IO = –10 mA 13.1 13.1
IO = 150 µA –14.7 –14.9 –14.7 –14.9
IO = 1.5 mA
IO = 15 mA –13.4 –13.8 –13.4 –13.8
IO = 100 µA –14.6 –14.6
IO = 1 mA
IO = 10 mA –13.4 –13.4

=

O

f = 1 MHz 25°C 30 30 Ω

IC

V
RS = 50 Ω

=

O

V

= 0, No load,

VIC = 2.5 V

,

=

ICR

= ±2.5 V to ±15 V,

S

L

,

S

VID = 1 V
VID = –1 V

=

= 2

=

25°C 7 100 7 100

Full range 250 250

25°C –0.7 –1.5 –0.7 –1.5

Full range –1.8 –1.8

25°C

Full range

25°C

Full range

25°C

Full range

25°C 100 170 100 170

Full range 20 20

25°C 85 108 85 108

Full range 80 80

25°C 90 106 90 106

Full range 85 85

°

25°C 13.8 18 13.8 18

Full range 18.8 18.8

= ±15 V (unless

CC±

°

µ

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

43

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

L

,

VD

,

V/µs

tsSettling time

s

VnEquivalent input noise voltage

V/√H

V

q

V

InEquivalent input noise current

A/√H

THD

N

O(PP)

,

L

,

0.01%

0.01%

Gain-bandwidth product

L

,

L

,

5.9

5.9

MH

B

g

O(PP)

,

L

,

668

668

kH

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2144M operating characteristics, V

SR+ Positive slew rate
SR– Negative slew rate

p

N(PP)

B

1

OM

φ

m

Peak-to-peak equivalent input
noise voltage

p

Total harmonic distortion plus V

+

noise
Unity-gain bandwidth RL = 2 kΩ, CL = 100 pF 6 6 MHz

Maximum output-swing V
bandwidth

Phase margin at unity gain RL = 2 kΩ, CL = 100 pF

p

R

= 2 kΩ, A

CL = 100 pF
AVD = –1, To 0.1% 0.34 0.34

10-V step To 0.01% .4 .4
RS = 20 Ω, f = 10 Hz 15 15
RS = 20 Ω, f = 1 kHz 10.5 10.5
f = 0.1 Hz to 1 Hz 0.48 0.48
f = 0.1 Hz to 10 Hz
f = 10 Hz 1.89 1.89
f = 10 kHz 0.47 0.47

= 20 V, R

AVD = 10,

R

= 2 kΩ, C

f = 100 kHz

= 20 V, R

AVD = 1,

= ±15 V, TA = 25°C

CC±

= –1,

= 2 kΩ,

f = 10 kHz

= 100 pF,

= 2 kΩ,

CL = 100 pF

TLE2144M TLE2144AM

MIN TYP MAX MIN TYP MAX

27 45 27 45
27 42 27 42

0.51 0.51

58° 58°

µ

n

z

µ

p

z

z

z

44

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

UNIT

V

O

0

15to15.3

ICR

gg

S

AVDLarge-signal differential voltage amplification

V

±10 V

R

kΩ

100

450

V/mV

k

Suppl

oltage rejection ratio (∆V

/∆VIO)

CC±

,

85

106

dB

IOSShort-circuit output current

V

0

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2141Y electrical characteristics at specified free-air temperature, V
(unless otherwise noted)

V
I

IO

I

IB

V

V

V

r
c
z
CMRR Common-mode rejection ratio VIC = V

I

CC

Input offset voltage

IO

Input offset current
Input bias current

Common-mode input voltage range RS = 50 Ω

ICR

Maximum positive peak output voltage swing

OM+

Maximum negative peak output voltage swing

OM–

p

Input resistance 65

i

Input capacitance 2.5 pF

i

Open-loop output impedance f = 1 MHz 30

o

pp

SVR

y-v

p

Supply current VO = 0, No load 3.5 4.5 mA

CC±

VIC = 0,

=

IO = –150 µA 13.8 14.1
IO = –1.5 mA
IO = –15 mA 13.3 13.7
IO = 150 µA –14.7 –14.9
IO = 1.5 mA
IO = 15 mA –13.4 –13.8

=

O

ICR

V

= ±2.5 V to ±15 V,

RS = 50 Ω

=

O

RS = 50 Ω,

,

min, RS = 50 Ω 80 108 dB

= 2

L

VID = 1 V –25 –50
VID = –1 V 20 31

= ±15 V, TA = 25°C

CC ±

TLE2141Y

MIN TYP MAX

200 1000 µV

7 100 nA

–0.7 –1.5 µA

–15 –15.3

13 13.2

13.7 14

–14.5 –14.8

to

V

V

V

MΩ

Ω

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

45

TLE214x, TLE214xA, TLE214xY

PARAMETER

TEST CONDITIONS

UNIT

V

O

0

15to15.3

ICR

gg

S

AVDLarge-signal differential voltage amplification

V

±10 V

R

2 kΩ

100

450

V/mV

k

Suppl

oltage rejection ratio (∆V

/∆VIO)

CC±

,

85

106

dB

IOSShort-circuit output current

V

0

mA

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2142Y electrical characteristics at specified free-air temperature, V

V
I
I

V

V

V

r
c
z
CMRR Common-mode rejection ratio VIC = V

I

Input offset voltage

IO

Input offset current

IO

Input bias current

IB

Common-mode input voltage range RS = 50 Ω

ICR

Maximum positive peak output voltage swing

OM+

Maximum negative peak output voltage swing

OM–

p

Input resistance 65

i

Input capacitance 2.5 pF

i

Open-loop output impedance f = 1 MHz 30

o

pp

SVR

CC

y-v

p

Supply current VO = 0, No load 6.9 9 mA

CC±

VIC = 0,

=

IO = –150 µA 13.8 14.1
IO = –1.5 mA
IO = –15 mA 13.3 13.7
IO = 150 µA –14.7 –14.9
IO = 1.5 mA
IO = 15 mA –13.4 –13.8

=

O

ICR

V

= ±2.5 V to ±15 V,

RS = 50 Ω

=

O

RS = 50 Ω,

,

min, RS = 50 Ω 80 108 dB

=

L

VID = 1 V –25 –50
VID = –1 V 20 31

= ±15 V, TA = 25°C

CC±

TLE2142Y

MIN TYP MAX

150 875 µV

7 100 nA

–0.7 –1.5 µA

–15 –15.3

13 13.2

13.7 14

–14.5 –14.8

to

V

V

V

MΩ

Ω

46

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PARAMETER

TEST CONDITIONS

UNIT

ICR

gg

S

IOSShort-circuit output current

V

0

mA

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TLE2144Y electrical characteristics at V

V
I

IO

I

IB

V

V

V

A
r
c
z
CMRR Common-mode rejection ratio VIC = V
k

I

CC

Input offset voltage

IO

Input offset current
Input bias current –0.7 –1.5 µA

Common-mode input voltage range RS = 50 Ω

ICR

Maximum positive peak output voltage swing

OM+

Maximum negative peak output voltage swing

OM–

Large-signal differential voltage amplification VO = ±10 V, RL = 2 kΩ 100 450 V/mV

VD

Input resistance 65 MΩ

i

Input capacitance 2.5 pF

i

Open-loop output impedance f = 1 MHz 30 Ω

o

Supply-voltage rejection ratio (∆V

SVR

p

Supply current VO = 0, No load 13.8 18 mA

/∆VIO) V

CC±

= ±15 V, TA = 25°C (unless otherwise noted)

CC±

VIC = 0, VO = 0 RS = 50 Ω,

IO = –150 µA 13.8 14.1
IO = –1.5 mA
IO = –15 mA 13.3 13.7
IO = 150 µA –14.7 –14.9
IO = 1.5 mA
IO = 15 mA –13.4 –13.8

CC±

=

O

TLE2144Y

MIN TYP MAX

0.3 1.8 mV
7 100 nA

–15 –15.3

to to

13 13.2

13.7 14

–14.5 –14.8

min, RS = 50 Ω 80 108 dB

ICR

= ±2.5 V to ±15 V, RS = 50 Ω 85 106 dB

VID = 1 V –25 –50
VID = –1 V 20 31

V

V

V

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

47

TLE214x, TLE214xA, TLE214xY

IIBInput bias current

g

vs Su ly voltage

7

V

Maximum positive peak output voltage

vs Su ly voltage

7

V

Maximum negative peak output voltage

AVDLarge-signal differential voltage amplification

qy

CMRR

Common-mode rejection ratio

qy

k

Suppl

oltage rejection ratio

qy

ICCSupply current

yg

SR

Slew rate

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TYPICAL CHARACTERISTICS

Table of Graphs

V

IO

I

IO

OM+

OM–

V

O(PP)

V

OH

V

OL

z

o

I

OS

SVR

V

n

V

n

I

n

THD + N Total harmonic distortion plus noise vs Frequency 28

B

1

φ

m

Input offset voltage Distribution 1, 2, 3
Input offset current vs Free-air temperature 4

p

p

p

Maximum peak-to-peak output voltage vs Frequency 12
High-level output voltage vs Output current 13
Low-level output voltage vs Output current 14

Closed-loop output impedance vs Frequency 17
Short-circuit output current vs Free-air temperature 18

pp

y-v

pp

Equivalent input noise voltage vs Frequency 25
Input noise voltage Over a 10-second period 26
Noise current vs Frequency 27

Pulse response

Unity-gain bandwidth vs Load capacitance 34
Gain margin vs Load capacitance 35
Phase margin vs Load capacitance 36
Phase shift vs Frequency 15

p

p

p

Noninverting large signal vs Time 31
Inverting large signal
Small signal vs Time 33

FIGURE

vs Common-mode input voltage 5
vs Free-air temperature 6

vs Supply voltage 7
vs Free-air temperature
vs Output current 9
vs Settling time 11

vs Supply voltage 7
vs Free-air temperature
vs Output current 10
vs Settling time 11

p

vs Frequency 15
vs Free-air temperature 16

vs Frequency 19
vs Free-air temperature 20

vs Frequency 21
vs Free-air temperature 22

vs Supply voltage 23
vs Free-air temperature 24

vs Free-air temperature 29
vs Load capacitance 30

vs Time 32

8

8

48

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TYPICAL CHARACTERISTICS

INPUT OFFSET VOLTAGE

24

236 Units Tested From 1 Wafer Lot

V

= ±15 V

CC±

TA = 25°C

20

P Package

16

12

8

Percentage of Units – %

4

0

–800

–400

VIO – Input Offset Voltage – µV

DISTRIBUTION OF

INPUT OFFSET VOLTAGE

24

250 Units Tested From 1 Wafer Lot
V

= ±15 V

CC±

TA = 25°C

20

N Package

16

TLE2141

DISTRIBUTION OF

0

400 800

Figure 1

TLE2144

INPUT OFFSET VOLTAGE

24

236 Units Tested From 1 Wafer Lot

V

= ±15 V

CC±

TA = 25°C

20

P Package

16

12

8

Percentage of Units – %

4

0

–800

–400

–600

VIO – Input Offset Voltage – µV

INPUT OFFSET CURRENT

FREE-AIR TEMPERATURE

20

VO = 0

18

VIC = 0

16

14

12

TLE2142

DISTRIBUTION OF

0

–200

200 600

Figure 2

vs

400 800

†

12

8

Percentage of Units – %

4

0
– 2 –1.2

–1.6 0

–0.8

VIO – Input Offset Voltage – mV

–0.4

0.8 1.6

0.4 1.2 2

Figure 3

†

Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

10

V

= ±2.5 V

CC±

CC±

= ±15 V

8

6

IO

IIO – Input Offset Current – nA

I

4
2
0

–75 –50 –25 0 25 50 75 100 125

TA – Free-Air Temperature – °C

V

Figure 4

150

49

TLE214x, TLE214xA, TLE214xY
EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TYPICAL CHARACTERISTICS

INPUT BIAS CURRENT

COMMON-MODE INPUT VOLTAGE

0

V

= ±2.5 V

CC±

–0.2

µAI

–0.4

–0.6

TA = 125°C

–0.8

–1

IB

IIB – Input Bias Current – uA

–1.2

–1.4

–3 –0.5

–2–2.5

VIC – Common-Mode Input Voltage – V

MAXIMUM PEAK OUTPUT VOLTAGE

SUPPLY VOLTAGE

24

RL = 2 kΩ
TA = 25°C

18

12

6

0

– 6

–12

– Maximum Peak Output Voltage – V

–18

OM

V

– 24

0 3 6 9 12 15

V

CC±

vs

TA = 25°C

TA = –55°C

–1.5 –1

Figure 5

vs

V

OM+

V

OM–

18 21 24

– Supply Voltage – V

†

0 0.5 1

INPUT BIAS CURRENT

vs

FREE-AIR TEMPERATURE

–1000

VO = 0
VIC = 0

–900

V

= ±2.5 V

–800

–700

IB

IIB – Input Bias Current – nA

I

–600

–500

–75 –50 –25 0 25 50 75 100 125 150

CC±

V

= ±15 V

CC±

TA – Free-Air Temperature – °C

Figure 6

MAXIMUM PEAK OUTPUT VOLTAGE

vs

FREE-AIR TEMPERATURE

15

V

= ±15 V

CC±

14.6

14.2

13.8

–13.8

–14.2

– Maximum Peak Output Voltage – V

–14.6

OM

V

–15

–75 –50 –25 0 25 50 75 100 125

TA – Free-Air Temperature – °C

RL = 2 kΩ

RL = ∞

V

OM+

RL = 2 kΩ

†

RL = ∞

V

OM–

150

Figure 7

†

Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

50

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

Figure 8

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TYPICAL CHARACTERISTICS

14.6

14.4

14.2

14

13.8

– Maximum Positive Peak Output Voltage – V

OM +

13.6

V

–0.1

V

CC±

MAXIMUM POSITIVE PEAK

OUTPUT VOLTAGE

vs

OUTPUT CURRENT

= ±15 V

TA = 125°C

TA = –55°C

–4–0.4 –1

IO – Output Current – mA

–10 –100– 40

Figure 9

†

TA = 25°C

–13.4

–13.6

–13.8

–14

–14.2

–14.4

–14.6

–14.8

– Maximum Negative Peak Output Voltage – V

OM –

– 15

V

0.1 10.4

MAXIMUM NEGATIVE PEAK

OUTPUT VOLTAGE

OUTPUT CURRENT

V

= ±15 V

CC±

TA = 125°C

TA = 25°C

IO – Output Current – mA

Figure 10

†

vs

TA = –55°C

104 10040

MAXIMUM PEAK-TO-PEAK

MAXIMUM PEAK OUTPUT VOLTAGE

vs

SETTLING TIME

12.5
AVD = –1

V

= ±15 V

CC±

10

TA = 25°C

7.5

5

2.5
0

–2.5

–5

–7.5

OM

–10

VOM – Maximum Peak Output Voltage – V

V

–12.5

0 100 200 300 400 500

Rising

Falling

ts – Settling Time – ns

0.1%

0.01%

0.1%

0.01%

30

25

20

15

10

TA = –55°C

5

– Maximum Peak-to-Peak Output Voltage – V

O(PP)

0

V

100 k 400 k 1 M

Figure 11

†

Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

OUTPUT VOLTAGE

vs

FREQUENCY

TA = 25°C

TA = 125°C

f – Frequency – Hz

Figure 12

†

V

= ±15 V

CC±

RL = 2 kΩ

4 M 10 M

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

51

TLE214x, TLE214xA, TLE214xY

†

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TYPICAL CHARACTERISTICS

HIGH-LEVEL OUTPUT VOLTAGE

vs

OUTPUT CURRENT

4.6
VCC = 5 V

4.4

4.2

4

3.8

– High-Level Output Voltage – V

3.6

OH

V

3.4

–0.1

TA = 25°C

TA = –55°C

TA = 125°C

–1 –10

IO – Output Current – mA

Figure 13

–100

LOW-LEVEL OUTPUT VOLTAGE

OUTPUT CURRENT

1400

VCC = 5 V

1200

TA = 125°C

1000

800

600

400

OL

200

V

VOL – Low-Level Output Voltage – mV

0

0.1 1 10
IO – Output Current – mA

Figure 14

†

vs

TA = 25°C

TA = –55°C

100

LARGE-SIGNAL DIFFERENTIAL VOLTAGE

AMPLIFICATION AND PHASE SHIFT

FREQUENCY

120
110
100

90

80

Phase Shift

70

60

50
40
30

Voltage Amplification – dB

VD

AVD – Large-Signal Differential

A

V

20

10

0

– 10

1 10 100 1 M

= ±15 V

CC±

RL = 2 kΩ
CL = 100 pF
TA = 25°C

f – Frequency – Hz

Figure 15

vs

A

VD

1 k 10 k 100 k

10 M

0°
20°
40°
60°
80°
100°
120°
140°
160°
180°
200°
220°
240°
260°

Phase Shift

†

Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

52

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TYPICAL CHARACTERISTICS

LARGE-SIGNAL DIFFERENTIAL

VOLTAGE AMPLIFICATION

FREE-AIR TEMPERATURE

140

RL = 10 kΩ

120

RL = 2 kΩ

100

Voltage Amplification – dB

VD

AVD – Large-Signal Differential

A

vs

†

V

= ±15 V

CC±

VO = ±10 V

80

CLOSED-LOOP OUTPUT IMPEDANCE

vs

FREQUENCY

100

Ωz

10

1

0.1

0.01

– Closed-Loop Output Impedance –

o

0.001
1 k 10 k 100 k 1 M

f – Frequency – Hz

–75 –50 – 25 0 25 50 75 100 125 150

TA – Free-Air Temperature – °C

Figure 16

SHORT-CIRCUIT OUTPUT CURRENT

FREE-AIR TEMPERATURE

60

30 Ω

VID = 1

TA – Free-Air Temperature – °C

AVD = 100
AVD = 10

AVD = 1

10 M

50

40

30

– Short-Circuit Output Current – mA

OS

I

20

–75 –50 – 25 0 25 50 75 100 125 150

vs

VID = –1

V

CC±

VO = 0

†

= ±15 V

Figure 17

†

Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

Figure 18

53

TLE214x, TLE214xA, TLE214xY

†

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TYPICAL CHARACTERISTICS

COMMON-MODE REJECTION RATIO

vs

FREQUENCY

140

120

100

80

60

40

20

CMRR – Common-Mode Rejection Ratio – dB

0

100 1 k 10 k

f – Frequency – Hz

V

CC±

TA = 25°C

Figure 19

= ±15 V

100 k 1 M

COMMON-MODE REJECTION RATIO

vs

FREE-AIR TEMPERATURE

120

VIC = V

116

112

108

104

CMRR – Common-Mode Rejection Ratio – dB

100

–75 –50 – 25 0 25 50 75 100 125 150

min

ICR

V

= ±15 V

CC±

TA – Free-Air Temperature – °C

VCC = 5 V

Figure 20

†

SUPPLY-VOLTAGE REJECTION RATIO

160

140

120

100

80

60

40

20

SVR

k

kSVR – Supply-Voltage Rejection Ratio – dB

0

10 100 1 k

k

SVR+

k

SVR–

V

= ±2.5 V to ±15 V

CC±

TA = 25°C

f – Frequency – Hz

Figure 21

vs

FREQUENCY

10 k 100 k 1 M

SUPPLY-VOLTAGE REJECTION RATIO

vs

FREE-AIR TEMPERATURE

110

108

10 M

106

104

102

SVR

k

kSVR – Supply-Voltage Rejection Ratio – dB

100

–75 –50 –25 0 25 50 75 100 125 150

TA – Free-Air Temperature – °C

V

= ±2.5 V to ±15 V

CC±

Figure 22

†

Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

54

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TYPICAL CHARACTERISTICS

SUPPLY CURRENT

vs

SUPPLY VOLTAGE

4

TA = 125°C

3.5

TA = 25°C

3

TA = –55°C

2.5

CC

I

IDD – Supply Current – mA

2

048121620

|V

| – Supply Voltage – V

CC±

Figure 23

EQUIVALENT INPUT NOISE VOLTAGE

vs

FREQUENCY

250

nV/ Hz

200

TA = –55°C

150

†

VO = 0
No Load

V

CC±

RS = 20Ω

24

†

= ±15 V

SUPPLY CURRENT

†

vs

FREE-AIR TEMPERATURE

3.8
VO = 0
No Load

3.6

3.4

3.2

CC

IDD – Supply Current – mA

I

3

2.8

–75 –50 –25 0 25 50 75 100 125 150

V

= ±15 V

CC±

V

= ±2.5 V

CC±

TA – Free-Air Temperature – °C

Figure 24

INPUT NOISE VOLTAGE

OVER A 10-SECOND PERIOD

750

V

= ±15 V

CC±

f = 0.1 to 10 Hz
TA = 25°C

500

250

100

50

Vn – Equivalent Input Noise Voltage –

0

1 100 1 k

TA = 125°C

TA = 25°C

10

f – Frequency – Hz

10 k

Figure 25

†

Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

0

–250

Input Noise Voltage – nV

–500

–750

0

246

t – Time – s

Figure 26

810

55

TLE214x, TLE214xA, TLE214xY

k

EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TYPICAL CHARACTERISTICS

8

Hz

6

TA = –55°C

4

– Noise Current – pA/

n

2

I

TA = 125°C

0

1

10 100 1 k 10 k

NOISE CURRENT

vs

FREQUENCY

TA = 25°C

f – Frequency – Hz

Figure 27

†

PLUS NOISE

vs

FREQUENCY

TOTAL HARMONIC DISTORTION

1%

V

= 20 V

O(PP)

V

= ±15 V

CC±

TA = 25°C

0.1%

AV = 10
RL = 600 Ω

0.01%

THD + N – Total Harmonic Distortion + Noise – %

0.001%
10 1 k 10 k 100

100

f – Frequency – Hz

AV = 100
RL = 600 Ω

AV = 100
RL = 2 kΩ

AV = 10
RL = 2 kΩ

Figure 28

SLEW RATE

†

vs

FREE-AIR TEMPERATURE

60

50

µs

40

30

20

SR – Slew Rate – V/

10

0
–75 –50 – 25 0 25 50 75 100 125 150

SR +

V

= ±15 V

CC±

AVD = – 1
RL = 2 kΩ
CL = 500 pF

TA – Free-Air Temperature – °C

SR –

Figure 29

50

40

µs

30

20

SR – Slew Rate – V/

V

= ±15 V

CC±

10

AVD = – 1
TA = 25°C

0

CL – Load Capacitance – nF

SLEW RATE

vs

LOAD CAPACITANCE

SR+

SR–

101 0.10.01

Figure 30

†

Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

56

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TYPICAL CHARACTERISTICS

NONINVERTING
LARGE-SIGNAL

PULSE RESPONSE

15

15

TA = 125°C

10

10

TA = 25°C

5

5

0

0

–5

O

V

VO – Output Voltage – V

–10

–10

–15

–15

01

TA = –55°C

V

= ±15 V

CC±

AVD = 1
RL = 2 kΩ
CL = 300 pF

t – Time – µs

2345

†

TA = –55°C

TA = 25°C

TA = 125°C

15

TA = 25°C

10

5

0

–5

O

V

VO – Output Voltage – V

–10

–15

Figure 31

INVERTING

LARGE-SIGNAL

PULSE RESPONSE

TA = –55°C

TA = 125°C

TA = 125°C

V

= ±15 V

CC±

AVD = –1
RL = 2 kΩ
CL = 300 pF

t – Time – µs

Figure 32

†

TA = –55°C

TA = 25°C

543210

V

VO – Output Voltage – mV

O

100

50

–50

–100

SMALL-SIGNAL

PULSE RESPONSE

7

TA = –55°C

6

5

0

V

= ±15 V

CC±

AVD = –1
RL = 2 kΩ
CL = 300 pF
TA = 25°C

4000 800 1200 1600

t – Time – ns

4

3

1

B1 – Unity-Gain Bandwidth – MHz

2

B

1

10 100

LOAD CAPACITANCE

TA = 25°C

TA = 125°C

CL – Load Capacitance – pF

Figure 33

vs

1000

Figure 34

UNITY-GAIN BANDWIDTH

†

V

= ±15 V

CC±

RL = 2 kΩ

10000

†

Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

57

TLE214x, TLE214xA, TLE214xY
EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

TYPICAL CHARACTERISTICS

14

12

10

8

6

Gain Margin – dB

4

2

0

10

GAIN MARGIN

†

vs

LOAD CAPACITANCE

V

= ±15 V

CC±

AVD = 1
RL = 2 kΩ to ∞
VO = –10 V to 10 V

TA = –55°C

TA = 125°C

TA = 25°C

1000100

CL – Load Capacitance – pF

Figure 35

10000

PHASE MARGIN

†

vs

LOAD CAPACITANCE

70°

60°

50°

40°

30°

– Phase Margin

m

φ

20°

10°

V

CC±

RL = 2 kΩ

0°

10 10000

TA = –55°C

TA = 25°C

TA = 125°C

= ±15 V

1000100

CL – Load Capacitance – pF

Figure 36

†

Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

58

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

APPLICATION INFORMATION

input offset voltage nulling

The TLE2141 series offers external null pins that can be used to further reduce the input offset voltage. If this
feature is desired, connect the circuit of Figure 37 as shown. If external nulling is not needed, the null pins may
be left unconnected.

3

IN+

IN–

OFFSET N2

Figure 37. Input Offset Voltage Null Circuit

+

2

–

5 kΩ

6

15

OFFSET N1

1 kΩ

OUT

V

(split supply)

CC–

GND (single supply)

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

59

TLE214x, TLE214xA, TLE214xY
EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

MECHANICAL INFORMATION

D (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE

14 PIN SHOWN

0.050 (1,27)

14

1

0.069 (1,75) MAX

A

0.020 (0,51)

0.014 (0,35)

0.010 (0,25)

0.004 (0,10)

DIM

8

7

PINS **

0.010 (0,25)

0.157 (4,00)

0.150 (3,81)

M

0.244 (6,20)

0.228 (5,80)

Seating Plane

0.004 (0,10)

8

14

0.008 (0,20) NOM

0°–8°

16

Gage Plane

0.010 (0,25)

0.044 (1,12)

0.016 (0,40)

A MAX

A MIN

NOTES: A. All linear dimensions are in inches (millimeters).

60

B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
D. Falls within JEDEC MS-012

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

0.197

(5,00)

0.189

(4,80)

0.344

(8,75)

0.337

(8,55)

0.394

(10,00)

0.386

(9,80)

4040047/D 10/96

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

MECHANICAL INFORMATION

DW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE

16 PIN SHOWN

0.050 (1,27)

16

1

0.020 (0,51)

0.014 (0,35)
9

0.299 (7,59)

0.293 (7,45)

8

A

0.010 (0,25)

0.419 (10,65)

0.400 (10,15)

M

0.010 (0,25) NOM

0°–8°

Gage Plane

0.010 (0,25)

0.050 (1,27)

0.016 (0,40)

0.104 (2,65) MAX

NOTES: A. All linear dimensions are in inches (millimeters).

B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15).
D. Falls within JEDEC MS-013

0.012 (0,30)

0.004 (0,10)

PINS **

DIM

A MAX

A MIN

Seating Plane

0.004 (0,10)

16

0.410

(10,41)

0.400

(10,16)

20

0.510

(12,95)

0.500

(12,70)

24

0.610

(15,49)

0.600

(15,24)

4040000/D 02/98

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

61

TLE214x, TLE214xA, TLE214xY
EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

MECHANICAL INFORMATION

FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER

28 TERMINAL SHOWN

A SQ

B SQ

20

22

23

24

25

19

21

12826 27

12

1314151618 17

0.020 (0,51)

0.010 (0,25)

MIN

0.342

0.442

0.640

0.739

0.938

1.141

A

0.358

(9,09)

0.458

(11,63)

0.660

(16,76)

0.761

(19,32)(18,78)

0.962

(24,43)

1.165

(29,59)

NO. OF

TERMINALS

**

11

10

9

8

7

6

5

432

20

28

44

52

68

84

0.020 (0,51)

0.010 (0,25)

(8,69)

(11,23)

(16,26)

(23,83)

(28,99)

MINMAX

0.307
(7,80)

0.406

(10,31)

0.495

(12,58)

0.495

(12,58)

0.850
(21,6)

1.047
(26,6)

0.080 (2,03)

0.064 (1,63)

B

MAX

0.358
(9,09)

0.458

(11,63)

0.560

(14,22)

0.560

(14,22)

0.858
(21,8)

1.063
(27,0)

0.055 (1,40)

0.045 (1,14)

0.028 (0,71)

0.022 (0,54)

0.050 (1,27)

NOTES: A. All linear dimensions are in inches (millimeters).

62

B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a metal lid.
D. The terminals are gold plated.
E. Falls within JEDEC MS-004

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

0.045 (1,14)

0.035 (0,89)

0.045 (1,14)

0.035 (0,89)

4040140/D 10/96

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

MECHANICAL INFORMATION

J (R-GDIP-T**) CERAMIC DUAL-IN-LINE PACKAGE

14 PIN SHOWN

14

1

B

0.065 (1,65)

0.045 (1,14)

0.100 (2,54)

0.070 (1,78)

8

C

7

0.020 (0,51) MIN

0.200 (5,08) MAX

PINS **

DIM

A MAX

A MIN

B MAX

B MIN

C MAX

C MIN

Seating Plane

0.310

(7,87)

0.290

(7,37)

0.785

(19,94)

0.755

(19,18)

0.280
(7,11)

0.245

(6,22)

0.310

(7,87)

0.290

(7,37)

0.785

(19,94)

0.755

(19,18)

0.300

(7,62)

0.245

(6,22)

A

181614

0.310

(7,87)

0.290
(7,37)

0.910

(23,10)

0.300
(7,62)

0.245
(6,22)

20

0.310

(7,87)

0.290

(7,37)

0.975

(24,77)

0.930

(23,62)

0.300

(7,62)

0.245

(6,22)

0.130 (3,30) MIN

0.100 (2,54)

0.023 (0,58)

0.015 (0,38)

NOTES: A. All linear dimensions are in inches (millimeters).

B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification only on press ceramic glass frit seal only.

E. Falls within MIL-STD-1835 GDIP1-T14, GDIP1-T16, GDIP1-T18, and GDIP1-T20

0°–15°

0.014 (0,36)

0.008 (0,20)
4040083/C 08/96

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

63

TLE214x, TLE214xA, TLE214xY
EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

MECHANICAL INFORMATION

JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE PACKAGE

0.400 (10,20)

0.355 (9,00)

0.063 (1,60)

0.015 (0,38)

0.100 (2,54)

8

1

5

4

0.065 (1,65)

0.045 (1,14)

0.020 (0,51) MIN

0.280 (7,11)

0.245 (6,22)

0.200 (5,08) MAX

0.130 (3,30) MIN

0.023 (0,58)

0.015 (0,38)

0.310 (7,87)

0.290 (7,37)

Seating Plane

0°–15°

0.014 (0,36)

0.008 (0,20)

NOTES: A. All linear dimensions are in inches (millimeters).

64

B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification only on press ceramic glass frit seal only.
E. Falls within MIL-STD-1835 GDIP1-T8

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

4040107/C 08/96

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

MECHANICAL INFORMATION

N (R-PDIP-T**) PLASTIC DUAL-IN-LINE PACKAGE

16 PIN SHOWN

16

1

0.035 (0,89) MAX

PINS **

DIM

A

9

0.260 (6,60)

0.240 (6,10)

8

0.070 (1,78) MAX

0.020 (0,51) MIN

0.200 (5,08) MAX

A MAX

A MIN

Seating Plane

14

0.775

(19,69)

0.745

(18,92)

16

0.775

(19,69)

0.745

(18,92)

18

0.920

(23.37)

0.850

(21.59)

20

0.975

(24,77)

0.940

(23,88)

0.310 (7,87)

0.290 (7,37)

0.100 (2,54)

0.021 (0,53)

0.015 (0,38)

NOTES: A. All linear dimensions are in inches (millimeters).

B. This drawing is subject to change without notice.

C. Falls within JEDEC MS-001 (20 pin package is shorter then MS-001.)

0.010 (0,25)

M

0.125 (3,18) MIN

0°–15°

0.010 (0,25) NOM

14/18 PIN ONL Y

4040049/C 08/95

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

65

TLE214x, TLE214xA, TLE214xY
EXCALIBUR LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

MECHANICAL INFORMATION

P (R-PDIP-T8) PLASTIC DUAL-IN-LINE PACKAGE

0.400 (10,60)

0.355 (9,02)

58

0.260 (6,60)

0.240 (6,10)

41

0.070 (1,78) MAX

0.020 (0,51) MIN

0.200 (5,08) MAX

0.125 (3,18) MIN

0.100 (2,54)

0.021 (0,53)

0.015 (0,38)

NOTES: A. All linear dimensions are in inches (millimeters).

B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001

0.010 (0,25)

M

0.310 (7,87)

0.290 (7,37)

Seating Plane

0°–15°

0.010 (0,25) NOM

4040082/B 03/95

66

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A – FEBRUARY 1997 – REVISED MARCH 1998

MECHANICAL INFORMATION

PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE

14 PIN SHOWN

0,65

14

1

1,20 MAX

A

7

0,05 MIN

0,30
0,19

8

6,60

4,50
4,30

6,20

M

0,10

Seating Plane

0,10

0,15 NOM

Gage Plane

0,25

0°–8°

0,75
0,50

PINS **

DIM

A MAX

A MIN

NOTES: A. All linear dimensions are in millimeters.

B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153

8

3,10

2,90

14

5,10

4,90

16

5,10

20

6,60

6,404,90

24

7,90

7,70

28

9,80

9,60

4040064/E 08/96

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

67

IMPORTANT NOTICE

T exas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.

TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty . Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.

CERTAIN APPLICA TIONS USING SEMICONDUCT OR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICA TIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERST OOD TO
BE FULLY AT THE CUSTOMER’S RISK.

In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.

TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.

Copyright  1999, Texas Instruments Incorporated