How it Works
Texas Instruments
Loading...
TLE 2082
INSTALLATION INSTRUCTIONS
37 pgs662.65 Kb0
Table of contents
Loading...

Texas Instruments TLE 2082 Y, TLE 2082 A, TLE 2082 INSTALLATION INSTRUCTIONS

Download
www.DataSheet4U.com

TLE2082, TLE2082A, TLE2082Y

0°C to 70°C
4 mV
TLE2082ACD
TLE2082ACP
40°C to 85°C
4 mV
TLE2082AID
TLE2082AIP
TLE2082Y
55°C to 125°C
4 mV
TLE2082AMD
TLE2082AMFK
TLE2082AMJG
TLE2082AMP
EXCALIBUR HIGH-SPEED
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
• 40-V/µs Slew Rate Typ
• High-Gain Bandwidth Product...10 MHz
• ±30-mA Minimum Short-Circuit Output
Current
• Wide Supply Range...±
TOTAL HARMONIC DISTORTION PLUS NOISE
FREQUENCY
1
V
= ±15 V
CC±
V
= 20 V
O(PP)
TA = 25°C
0.1
AV = 100, RL = 600Ω
AV = 100, RL = 2 kΩ AV = 10, RL = 600Ω
0.01
THD + N – Total Harmonic Distortion + Noise – %
0.001
AV = 10, RL = 2 kΩ
Filter: 10-Hz to 500-kHz Band Pass
10 100 1 k 10 k 100 k
f – Frequency – Hz
  ±
vs
• Fast Settling Time Using 10-V Step
400 ns to 10 mV Typ
1.5 µs to 1 mV Typ
• Input Range Includes the Positive Supply
• Macromodel Included
OUTPUT VOLTAGE
vs
SETTLING TIME
12.5 10
7.5
5
2.5 0
–2.5
O
– 5
V
VO – Output Voltage – V
– 7.5
– 10
– 12.5
0 0.5 1 1.5
10 mV
Rising
Falling
10 mV
ts – Settling Time – µs
1 mV
1 mV
V
= ±15 V
CC±
RL = 1 kΩ CL = 100 pF AV = –1 TA = 25°C
2

description

The TLE2082 and TLE2082A are high-performance, high-speed, internally compensated JFET-input dual operational amplifiers built using T exas Instruments complementary bipolar Excalibur process. The TLE2082A has a lower input offset voltage than the TLE2082. Both are pin-compatible upgrades to standard industry products.
AVAILABLE OPTIONS
PACKAGED DEVICES
T
A
°
°
–
°
–
The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2082ACDR). Chip-form versions are tested at TA = 25°C. For chip-form orders, contact your local TI sales office.
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
VIOmax AT 25°C
°
4 mV TLE2082ACD 7 mV
4 mV TLE2082AID
°
7 mV 4 mV TLE2082AMD TLE2082AMFK TLE2082AMJG TLE2082AMP
°
7 mV
TLE2082CD
TLE2082ID
TLE2082MD
SMALL
OUTLINE
(D)
CHIP
CARRIER
(FK)
— —
— —
TLE2082MFK
CERAMIC
DIP
(JG)
TLE2082MJG
PLASTIC
DIP
(P)
TLE2082ACP TLE2082CP
TLE2082AIP TLE2082IP
TLE2082MP
Copyright 1994, Texas Instruments Incorporated
On products compliant to MIL-STD-883, Class B, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters.
CHIP FORM
(Y)
—
—
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082, TLE2082A, TLE2082Y EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994

description (continued)

The design features a 28-V/µs minimum slew rate, which results in a high-power bandwidth. Settling time to
0.1% of a 10-V step (1 kΩ/100-pF load) is approximately 400 ns. Gain-bandwidth product is typically 10 MHz with an 8-MHz minimum. As such, the TLE2082 and TLE2082A offer significant speed and noise advantages at a low 1.5-mA typical supply current per channel.
The input current characteristics traditionally associated with JFET-input amplifiers have been maintained. The input offset voltage is graded to a 7-mV and a 4-mV maximum for the TLE2082 and the TLE2082A, respectively . Typically , temperature coef ficient of input offset voltage is 2.4 µV/°C and typical CMRR and k 99 dB, respectively. Device performance is relatively independent of supply voltage over the wide ±2.25-V to ±19-V range. The input common-mode voltage range extends from the positive supply down to V without significant degradation to dynamic performance. Maximum peak output voltage swing is from V
CC+
– 1 V to V
+ 1 V under light loading conditions. The output is capable of sourcing and sinking currents
CC–
to at least 30 mA and can sustain shorts to either supply . Care must be taken to ensure that maximum power dissipation is not exceeded.
Both the TLE2082 and TLE2082A are available in a wide variety of packages, including both the industry-standard 8-pin small-outline version and chip form for high-density system applications. The C-suffix devices are characterized for operation from 0°C to 70°C, the I-suffix devices over the – 40°C to 85°C range, and the M-suffix devices over the full military temperature range of –55°C to 125°C.
are 98 dB and
SVR
CC–
+ 4 V

symbol

IN+
IN–
D, JG, OR P PACKAGE
(TOP VIEW)
1OUT
1IN–
1IN +
V
CC–
1 2 3 4
+
–
8 7 6 5
V
CC+
2OUT 2IN– 2IN+
OUT
FK PACKAGE
(TOP VIEW)
1OUT
NCNCNC
CC –
CC +
V
2IN +
NC
NC
1IN–
NC
1IN+
NC
NC – No internal connection
3212019
4 5 6 7 8
910111213
NCVNC
18 17 16 15 14
NC 2OUT NC 2IN– NC
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082, TLE2082A, TLE2082Y
EXCALIBUR HIGH-SPEED
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994

TLE2082Y chip information

This chip, when properly assembled, displays characteristics similar to the TLE2082. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive epoxy or a gold-silicon preform.
90
(1)
(2)
(3)
BONDING PAD ASSIGNMENTS
(8)
(4)
80
(7)
(6)
(5)
V
CC+
(3)
1IN+
(2)
1IN–
(7)
2OUT
CHIP THICKNESS: 15 TYPICAL BONDING PADS: 4 × 4 MINIMUM TJmax = 150°C TOLERANCES ARE ±10%. ALL DIMENSIONS ARE IN MILS. PIN (4) IS INTERNALLY CONNECTED
TO BACKSIDE OF THE CHIP.
(8)
+
–
V
CC–
(4)
(1)
1OUT
(5)
+
–
(6)
2IN+
2IN–
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082, TLE2082A, TLE2082Y EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
5
37
Transistors
Resistors
Diodes
CC+
V
11
Capacitors
57
ACTUAL DEVICE
COMPONENT COUNT
R11
R6
Q17
Q23
Q28
D2
Q20
Q13
Q24
D3
R13
Q19
Q15
OUT
R12
Q30
Q16
R8
C6
Q25
C3
Q29
Q18
Q26 Q27
Q22
Q21
Q14
R14
Q31
C5
R7
R10
R9
C4
R5
CC–
V
R2
R1
Q1
equivalent schematic (each channel)
R4
C2
Q3
Q8
R3
C1
Q12
Q9
Q4
Q5
IN–
IN+
Q10
Q6
Q7
D1
Q2
Q11
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
TLE2082, TLE2082A, TLE2082Y
PACKAGE
A
UNIT
C
V
V
EXCALIBUR HIGH-SPEED
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)

Supply voltage, V Supply voltage, V Differential input voltage range, V Input voltage range, V Input current, I
(each input) ±1 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I
Output current, I Total current into V Total current out of V
Duration of short-circuit current at (or below) 25°C (see Note 3) unlimited. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, T
Storage temperature range –65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Case temperature for 60 seconds: FK package 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D or P package 260°C. . . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: JG package 300°C. . . . . . . . . . . . . . . . . . . .
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values except differential voltages are with respect to the midpoint between V
2. Differential voltages are at IN+ with respect to IN–.
3. The output may be shorted to either supply. Temperatures and/or supply voltages must be limited to ensure that the maximum dissipation rate is not exceeded.
D 725 mW 5.8 mW/°C 464 mW 377 mW 145 mW FK 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW JG 1050 mW 8.4 mW/°C 672 mW 546 mW 210 mW
P 1000 mW 8.0 mW/°C 640 mW 344 mW 200 mW
(see Note 1) 19 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CC+
(see Note 1) –19 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CC–
(any input) V
I
(each output) ±80 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
O
160 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CC+
160 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CC–
(see Note 2) V
ID
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
: C suffix 0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A
CC+ CC+
I suffix –40°C to 85°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
M suffix –55°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
and V
CC+
DISSIPATION RATING TABLE
TA ≤ 25°C DERATING FACTOR TA = 70°C TA = 85°C TA = 125°C
POWER RATING ABOVE TA = 25°CAPOWER RATINGAPOWER RATINGAPOWER RATING
CC–
.
to V to V
CC– CC–
†

recommended operating conditions

Supply voltage, V
ommon-mode input voltage,
Operating free-air temperature, T
CC±
IC
A
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
C SUFFIX I SUFFIX M SUFFIX MIN MAX MIN MAX MIN MAX
±2.25 ±19 ±2.25 ±19 ±2.25 ±19 V
V
= ±5 V –0.9 5 –0.8 5 –0.8 5
CC±
V
= ±15 V –10.9 15 –10.8 15 –10.8 15
CC±
0 70 –40 85 –55 125 °C
TLE2082, TLE2082A, TLE2082Y
PARAMETER
TEST CONDITIONS
†
UNIT
VIOI
V
IC O
IIOI
t
VIC 0, VO 0, IIBI
t
5to5to5to5
V
Common mode input R
50 Ω
V
gg
5to5
g
I
200 µA
V
Maximum positive peak I
2 mA
V
I
A
I
200 µA
V
Maximum negative peak I
2 mA
V
I
A
R
600 Ω
A
Large signal differential V
± 2.3 V
R
2 kΩ
dB
R
kΩ
Input
V
0
S
5
F
CMRR
C
VIC V
ICR
min,
dB
k
Supply voltage rejection
V
CC±
±5 V to ±15 V,
dB
I
pp y
V
No load
A
EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, V
T
A
nput offset voltage
α
r
i
c
z
CC
†
Full range is 0°C to 70°C.
Temperature coefficient
VIO
of input offset voltage
nput offset curren
nput bias curren
Common-mode input
ICR
voltage range
Maximum positive peak
OM+
output voltage swing
Maximum negative peak
OM–
output voltage swing
Large-signal differential
VD
voltage amplification
Input resistance VIC = 0 25°C Input
i
capacitance Open-loop output impedance f = 1 MHz 25°C 80 80 Ω
o
ommon-mode rejection ratio
Supply-voltage rejection V
SVR
ratio(∆V
CC±
Supply current (both channels)
Common mode Differential
/∆VIO)
VIC = 0, VO = 0, RS = 50 Ω
VIC = 0, VO = 0, See Figure 4
=
S
= –
O
= –
O
= –20 m
O
=
O
=
O
= 20 m
O
=
L
=
O
,
=
IC
VIC = V
ICR
VO = 0, RS = 50 Ω
= ±5 V to ±15 V,
CC±
VO = 0, RS = 50 Ω
= 0,
O
min,
=
L
= 10
L
ee Figure
25°C 0.9 6 0.65 4
Full range 8.1 5.1 Full range 2.3 25 2.3 25 µV/°C
25°C 5 100 5 100 pA
Full range 1.4 1.4 nA
25°C 15 175 15 175 pA
Full range 5 5 nA
25°C
Full range
25°C 3.8 4.1 3.8 4.1
Full range 3.7 3.7
25°C 3.5 3.9 3.5 3.9
Full range 3.4 3.4
25°C 1.5 2.3 1.5 2.3
Full range 1.5 1.5
25°C –3.8 –4.2 –3.8 –4.2
Full range –3.7 –3.7
25°C –3.5 –4.1 –3.5 –4.1
Full range –3.4 –3.4
25°C –1.5 –2.4 –1.5 –2.4
Full range –1.5 –1.5
25°C 80 91 80 91
Full range 79 79
25°C 90 100 90 100
Full range 89 89
25°C 95 106 95 106
Full range 94 94
25°C 11 11 25°C 2.5 2.5
25°C 70 89 70 89
Full range 68 68
25°C 82 99 82 99
Full range 80 80
25°C 2.7 2.9 3.6 2.7 2.9 3.6
Full range 3.6 3.6
= ±5 V (unless otherwise noted)
CC±
TLE2082C TLE2082AC
MIN TYP MAX MIN TYP MAX
5 5 5 5
to
–1 –1.9 –1 –1.9
5 5
to
–0.9 –0.9
10
12
10
12
m
Ω
p
m
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082, TLE2082A, TLE2082Y
PARAMETER
TEST CONDITIONS
UNIT
IOSShort-ci
t
V
0
25°C
A
PARAMETER
TEST CONDITIONS
†
UNIT
A
R
C
L
100 pF,See Figure 1
tsSettli
2 V step,
25°C
V
Equivalent input noise
25°C
S
f 10 Hz to
6
6
V
pq
25°C
V
THD
N
Total harmonic distortion f
R
25°C
0.013%
0.013%
B1Unit
idth
VI 10 mV, RL 2 kΩ,
25°C
9.4
9.4
MH
B
Maximum output swing
O(PP)
,
VD
,
25°C
2.8
2.8
MH
φ
gy
I
,
L
,
25°C
56°
56°
EXCALIBUR HIGH-SPEED
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, V (continued)
T
A
Crosstalk attenuation VIC = 0, RL = 2 kΩ 25°C 120 120 dB
rcuit output curren
=
O
VID = 1 V VID = –1 V
°
operating characteristics at specified free-air temperature, V
T
A
MIN TYP MAX MIN TYP MAX
25°C 35 35
SR+ Positive slew rate
SR– Negative slew rate
ng time
n
N(PP)
I
n
OM
m
†
Full range is 0°C to 70°C.
Equivalent input noise voltage
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
Total harmonic distortion
+
plus noise
y-gain bandw
Maximum output-swing bandwidth
Phase margin at unity VI = 10 mV, RL = 2 kΩ, gain
V
= ±2.3 V ,
O(PP)
–
= –1,
VD
= 100 pF,See Figure 1
=
C
AVD = –1, 2-V step, RL = 1 kΩ, CL = 100 pF
RS = 20 Ω, See Figure 3
VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz V
= 5 V, AVD = 10,
O(PP)
= 1 kHz,
RS = 25 Ω VI = 10 mV, RL = 2 kΩ,
CL = 25 pF, See Figure 2 V
= 4 V, AVD = –1,
O(PP)
RL = 2 kΩ ,C
CL = 25 pF, See Figure 2
= 2 kΩ,
L
To 10 mV
To 1 mV f = 10 Hz
f = 10 kHz f = 10 Hz to
10 kHz
f = 0.1Hz to
10 Hz
= 2 kΩ,
L
= 25 pF
L
Full
range
25°C 38 38
Full
range
°
°
°
°
°
°
°
22 22
22 22
= ±5 V (unless otherwise noted)
CC±
TLE2082C TLE2082AC
MIN TYP MAX MIN TYP MAX
–35 –35
45 45
= ±5 V
CC±
TLE2082C TLE2082AC
0.25 0.25
0.4 0.4 28 28
11.6 11.6
0.6 0.6
°
°
m
V/µs
V/µs
µs
nV/√Hz
µ
z
z
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082, TLE2082A, TLE2082Y
PARAMETER
TEST CONDITIONS
†
UNIT
VIOI
V
IC O
IIOI
t
VIC 0, VO 0, IIBI
t
15to15to15to15
V
Common mode input R
50 Ω
V
gg
15to15
g
I
200 µA
V
Maximum positive peak I
2 mA
V
I
A
I
200 µA
V
Maximum negative peak I
2 mA
V
I
A
R
600 Ω
A
Large signal differential V
± 10 V
R
2 kΩ
dB
R
kΩ
c
i
capacitance
VIC 0, See Figure 5
pF
CMRR
Common mode
VIC V
ICR
min,
dB
k
Supply voltage rejection
V
CC±
±5 V to ±15 V,
dB
I
pp y
V
No load
A
EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, V
T
A
nput offset voltage
α
r
i
c
z
CC
†
Full range is 0°C to 70°C.
Temperature coefficient
VIO
of input offset voltage
nput offset curren
nput bias curren
Common-mode input
ICR
voltage range
Maximum positive peak
OM+
output voltage swing
Maximum negative peak
OM–
output voltage swing
Large-signal differential
VD
voltage amplification
Input resistance VIC = 0 25°C
Input
i
Open-loop output impedance f = 1 MHz 25°C 80 80 Ω
o
Common-mode VIC = V rejection ratio
Supply-voltage rejection V
SVR
ratio (∆V Supply current
(both channels)
CC±
/∆VIO)
Common mode
Differential
VIC = 0, VO = 0, RS = 50 Ω
VIC = 0, VO = 0, See Figure 4
=
S
= –
O
= –
O
= –20 m
O
=
O
=
O
= 20 m
O
=
L
=
O
VIC = 0, See Figure 5
ICR
VO = 0, RS = 50 Ω
= ±5 V to ±15 V,
CC±
VO = 0, RS = 50 Ω
= 0,
O
min,
=
L
= 10
L
25°C 1.1 7 0.7 4
Full range 8.1 5.1 Full range 2.4 25 2.4 25 µV/°C
25°C 6 100 6 100 pA
Full range 1.4 1.4 nA
25°C 20 175 20 175 pA
Full range 5 5 nA
25°C
Full range
25°C 13.8 14.1 13.8 14.1
Full range 13.6 13.6
25°C 13.5 13.9 13.5 13.9
Full range 13.4 13.4
25°C 11.5 12.3 11.5 12.3
Full range 11.5 11.5
25°C –13.8 –14.2 –13.8 –14.2
Full range –13.7 –13.7
25°C –13.5 –14 –13.5 –14
Full range –13.4 –13.4
25°C –11.5 –12.4 –1 1.5 –12.4
Full range –1 1.5 –11.5
25°C 80 96 80 96
Full range 79 79
25°C 90 109 90 109
Full range 89 89
25°C 95 118 95 118
Full range 94 94
25°C 7.5 7.5 25°C 2.5 2.5
25°C 80 98 80 98
Full range 79 79
25°C 82 99 82 99
Full range 81 81
25°C 2.7 3.1 3.6 2.7 3.1 3.6
Full range 3.6 3.6
= ±15 V (unless otherwise noted)
CC±
TLE2082C TLE2082AC
MIN TYP MAX MIN TYP MAX
15 15 15 15
to
–11 –11.9 –11 –11.9
15 15
to
–10.9 –10.9
10
12
10
12
m
Ω
pF
m
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082, TLE2082A, TLE2082Y
PARAMETER
TEST CONDITIONS
UNIT
IOSShort-ci
t
V
0
25°C
A
PARAMETER
TEST CONDITIONS
†
UNIT
R
C
100 pF
g
See Figure 1
tsSettli
10 V step,
25°C
V
Equivalent input noise
25°C
RS 20 Ω,
f 10 Hz to
6
6
Peak to peak equivalent
0.6
0.6
THD
N
Total harmonic distortion f
R
25°C
0.008%
0.008%
B1Unit
idth
VI 10 mV, RL 2 kΩ,
25°C810810
MH
B
Maximum output swing
O(PP)
,
VD
,
25°C
kH
φ
Phase margin at
VI 10 mV, RL 2 kΩ,
25°C
57°
57°
EXCALIBUR HIGH-SPEED
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, V (continued)
T
A
Crosstalk attenuation VIC = 0, RL = 2 kΩ 25°C 120 120 dB
rcuit output curren
=
O
VID = 1 V VID = –1 V
°
operating characteristics at specified free-air temperature, V
T
SR+ Positive slew rate
SR– Negative slew rate
ng time
n
V
N(PP)
I
n
OM
m
†
Full range is 0°C to 70°C.
Equivalent input noise voltage
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
Total harmonic distortion
+
plus noise
y-gain bandw
Maximum output-swing bandwidth
Phase margin at VI = 10 mV, RL = 2 kΩ, unity gain
A
25°C 28 40 28 40
V
= 10 V, AVD = –1,
O(PP)
= 2 kΩ,
L
ure 1
See Fi
AVD = –1, 10-V step, RL = 1kΩ, CL = 100 pF
RS = 20 Ω, f = 10 Hz to See Figure 3
VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz V
= 20 V, AVD = 10,
O(PP)
= 1 kHz,
RS = 25 Ω VI = 10 mV, RL = 2 kΩ,
CL = 25 pF, See Figure 2 V
= 20 V, AVD = –1,
O(PP)
RL = 2 kΩ,C
CL = 25 pF, See Figure 2
=
L
To 10 mV
To 1 mV f = 10 Hz
f = 10 kHz
10 kHz
f = 0.1 Hz to
10 Hz
= 2 kΩ,
L
= 25 pF
L
Full
range
,
25°C 30 45 30 45
Full
range
25°C
MIN TYP MAX MIN TYP MAX
25 25
25 25
°
°
°
°
°
°
= ±15 V (unless otherwise noted)
CC±
TLE2082C TLE2082AC
MIN TYP MAX MIN TYP MAX
–30 –45 –30 –45
30 48 30 48
= ±15 V
CC±
TLE2082C TLE2082AC
0.4 0.4
1.5 1.5 28 28
11.6 11.6
°
°
m
V/µs
V/µs
µs
nV/√Hz
µV
z
z
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082, TLE2082A, TLE2082Y
PARAMETER
TEST CONDITIONS
†
UNIT
VIOI
V
IC O
IIOI
t
VIC 0, VO 0, IIBI
t
5to5to5to5
V
Common mode input R
50 Ω
V
gg
5to5
g
I
200 µA
V
Maximum positive peak I
2 mA
V
I
A
I
200 µA
V
Maximum negative peak I
2 mA
V
I
A
R
600 Ω
A
Large signal differential V
± 2.3 V
R
2 kΩ
R
kΩ
Input
V
0
S
5
F
CMRR
C
VIC V
ICR
min,
dB
k
Supply voltage rejection ratio
V
CC±
±5 V to ±15 V,
dB
ICCS
)
V
No load
A
EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, V
T
A
nput offset voltage
α
r
i
c
z
†
Full range is –40°C to 85°C.
Temperature coefficient
VIO
of input offset voltage
nput offset curren
nput bias curren
Common-mode input
ICR
voltage range
Maximum positive peak
OM+
output voltage swing
Maximum negative peak
OM–
output voltage swing
Large-signal differential
VD
voltage amplification
Input resistance VIC = 0 25°C Input
i
capacitance Open-loop output impedance f = 1 MHz 25°C 80 80 Ω
o
ommon-mode rejection ratio
Supply-voltage rejection ratio V
SVR
(∆V
/∆VIO)
CC±
upply current (both channels
Common mode Differential
VIC = 0, VO = 0, RS = 50 Ω
VIC = 0, VO = 0, See Figure 4
=
S
= –
O
= –
O
= –20 m
O
=
O
=
O
= 20 m
O
=
L
=
O
,
=
IC
VIC = V
ICR
VO = 0, RS = 50 Ω
= ±5 V to ±15 V,
CC±
VO = 0, RS = 50 Ω
= 0,
O
min,
=
L
= 10
L
ee Figure
25°C 0.9 7 0.65 4
Full range 8.5 5.5 Full range 2.4 25 2.4 25 µV/°C
25°C 5 100 5 100 pA
Full range 5 5 nA
25°C 15 175 15 175
Full range 10 10
25°C
Full range
25°C 3.8 4.1 3.8 4.1
Full range 3.7 3.7
25°C 3.5 3.9 3.5 3.9
Full range 3.4 3.4
25°C 1.5 2.3 1.5 2.3
Full range 1.5 1.5
25°C –3.8 –4.2 –3.8 –4.2
Full range –3.7 –3.7
25°C –3.5 –4.1 –3.5 –4.1
Full range –3.4 –3.4
25°C –1.5 –2.4 –1.5 –2.4
Full range –1.5 –1.5
25°C 80 91 80 91
Full range 79 79
25°C 90 100 90 100 dB
Full range 89 89
25°C 95 106 95 106
Full range 94 94
25°C 11 11 25°C 2.5 2.5
25°C 70 89 70 89
Full range 68 68
25°C 82 99 82 99
Full range 80 80
25°C 2.7 2.9 3.6 2.7 2.9 3.6
Full range 3.6 3.6
= ±5 V (unless otherwise noted)
CC±
TLE2082I TLE2082AI
MIN TYP MAX MIN TYP MAX
5 5 5 5
to
–1 –1.9 –1 –1.9
5 5
to
–0.8 –0.8
10
12
10
12
m
pA nA
Ω
p
m
5–10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082, TLE2082A, TLE2082Y
PARAMETER
TEST CONDITIONS
UNIT
IOSShort-ci
t
V
0
25°C
A
PARAMETER
TEST CONDITIONS
†
UNIT
A
R
C
L
100 pF,See Figure 1
tsSettli
2 V step,
25°C
V
Equivalent input noise
25°C
S
,
f 10 Hz to
6
6
V
Peak to peak equivalent
25°CµV
f 0.1 Hz to
0.6
0.6
THD
N
Total harmonic distortion f
R
2 kΩ
25°C
0.013%
0.013%
B1Unit
idth
VI 10 mV, RL 2 kΩ,
25°C
9.4
9.4
MH
B
Maximum output swing
O(PP)
,
VD
,
25°C
2.8
2.8
MH
φ
gy
I
,
L
,
25°C
56°
56°
EXCALIBUR HIGH-SPEED
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, V (continued)
T
A
Crosstalk attenuation VIC = 0, RL = 2 kΩ 25°C 120 120 dB
rcuit output curren
=
O
VID = 1 V VID = –1 V
°
operating characteristics at specified free-air temperature, V
T
SR+ Positive slew rate
SR– Negative slew rate
ng time
n
N(PP)
I
n
OM
m
†
Full range is 40°C to 85°C.
Equivalent input noise voltage
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
Total harmonic distortion
+
plus noise
y-gain bandw
Maximum output-swing bandwidth
Phase margin at unity VI = 10 mV, RL = 2 kΩ, gain
A
25°C 35 35
V
= ±2.3 V ,
O(PP)
–
= –1,
VD
= 100 pF,See Figure 1
=
C
AVD = –1, 2-V step, RL = 1 kΩ, CL = 100 pF
RS = 20 Ω, See Figure 3
VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz V
= 5 V, AVD = 10,
O(PP)
= 1 kHz,
RS = 25 Ω VI = 10 mV, RL = 2 kΩ,
CL = 25 pF, See Figure 2 V
= 4 V, AVD = –1,
O(PP)
RL = 2 kΩ ,C
CL = 25 pF, See Figure 2
= 2 kΩ,
L
To 10 mV
To 1 mV f = 10 Hz
f = 10 kHz f = 10 Hz to
10 kHz
f = 0.1 Hz to
10 Hz
,
=
L
= 25 pF
L
Full
range
25°C 38 38
Full
range
MIN TYP MAX MIN TYP MAX
20 20
20 20
°
°
°
°
°
°
°
= ±5 V (unless otherwise noted)
CC±
TLE2082I TLE2082AI
MIN TYP MAX MIN TYP MAX
–35 –35
45 45
= ±5 V
CC±
TLE2082I TLE2082AI
0.25 0.25
0.4 0.4 28 28
11.6 11.6
°
°
m
V/µs
V/µs
µs
nV/√Hz
z
z
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
5–11
TLE2082, TLE2082A, TLE2082Y
PARAMETER
TEST CONDITIONS
†
UNIT
VIOI
V
IC O
IIOI
t
VIC 0, VO 0, IIBI
t
15to15to 15
15
V
Common mode input R
50 Ω
V
gg
15
15
g
I
200 µA
V
Maximum positive peak I
2 mA
V
I
A
I
200 µA
V
Maximum negative peak I
2 mA
V
I
A
R
600 Ω
A
Large signal differential V
± 10 V
R
2 kΩ
dB
R
kΩ
c
i
capacitance
VIC 0, See Figure 5
pF
CMRR
Common mode
VIC V
ICR
min,
dB
k
Supply voltage rejection ratio
V
CC±
±5 V to ±15 V,
dB
I
Supply current V
No load
A
EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, V
T
A
nput offset voltage
α
r
i
c
z
CC
†
Full range is –40°C to 85°C.
Temperature coefficient
VIO
of input offset voltage
nput offset curren
nput bias curren
Common-mode input
ICR
voltage range
Maximum positive peak
OM+
output voltage swing
Maximum negative peak
OM–
output voltage swing
Large-signal differential
VD
voltage amplification
Input resistance VIC = 0 25°C
Input
i
Open-loop output impedance f = 1 MHz 25°C 80 80 Ω
o
Common-mode VIC = V rejection ratio
Supply-voltage rejection ratio V
SVR
(∆V Supply current
(both channels)
CC±
/∆VIO)
Common mode
Differential
VIC = 0, VO = 0, RS = 50 Ω
VIC = 0, VO = 0, See Figure 4
=
S
= –
O
= –
O
= –20 m
O
=
O
=
O
= 20 m
O
=
L
=
O
VIC = 0, See Figure 5
ICR
VO = 0, RS = 50 Ω
= ±5 V to ±15 V,
CC±
VO = 0, RS = 50 Ω
= 0,
O
min,
=
L
= 10
L
25°C 1.1 7 0.7 4
Full range 8.5 5.5 Full range 2.4 25 2.4 25 µV/°C
25°C 6 100 6 100 pA
Full range 5 5 nA
25°C 20 175 20 175 pA
Full range 10 10 nA
25°C
Full range
25°C 13.8 14.1 13.8 14.1
Full range 13.7 13.7
25°C 13.5 13.9 13.5 13.9
Full range 13.4 13.4
25°C 1 1.5 12.3 1 1.5 12.3
Full range 11.5 11.5
25°C –13.8 –14.2 –13.8 –14.2
Full range –13.7 –13.7
25°C –13.5 –14 –13.5 –14
Full range –13.4 –13.4
25°C –11.5 –12.4 –11.5 –12.4
Full range –11.5 –11.5
25°C 80 96 80 96
Full range 79 79
25°C 90 109 90 109
Full range 89 89
25°C 95 118 95 118
Full range 94 94
25°C 7.5 7.5 25°C 2.5 2.5
25°C 80 98 80 98
Full range 79 79
25°C 82 99 82 99
Full range 80 80
25°C 2.7 3.1 3.6 2.7 3.1 3.6
Full range 3.6 3.6
= ±15 V (unless otherwise noted)
CC±
TLE2082I TLE2082AI
MIN TYP MAX MIN TYP MAX
15 15 15 15
to
–11 –11.9 –11 –11.9
15 15
to
–10.8 –10.8
12
10
to
10
to
12
m
Ω
pF
m
5–12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082, TLE2082A, TLE2082Y
PARAMETER
TEST CONDITIONS
UNIT
IOSShort-ci
t
V
0
25°C
A
PARAMETER
TEST CONDITIONS
†
UNIT
R
C
100 pF
g
See Figure 1
tsSettli
10 V step,
25°C
V
Equivalent input noise
25°C
S
,
f 10 Hz to
6
6
V
Peak to peak equivalent
25°CµV
f 0.1 Hz to
0.6
0.6
THD
N
Total harmonic distortion f
R
2 kΩ
25°C
0.008%
0.008%
B1Unit
idth
VI 10 mV, RL 2 kΩ,
25°C810810
MH
B
Maximum output swing
O(PP)
,
VD
,
25°C
kH
φ
gy
I
,
L
,
25°C
57°
57°
EXCALIBUR HIGH-SPEED
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, V
= ±15 V (unless otherwise noted)
CC±
(continued)
T
A
Crosstalk attenuation VIC = 0, RL = 2 kΩ 25°C 120 120 dB
rcuit output curren
=
O
VID = 1 V VID = –1 V
°
operating characteristics at specified free-air temperature, V
T
A
25°C 28 40 28 40
SR+ Positive slew rate
SR– Negative slew rate
ng time
n
N(PP)
I
n
OM
m
†
Full range is –40°C to 85°C.
Equivalent input noise voltage
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
Total harmonic distortion
+
plus noise
y-gain bandw
Maximum output-swing bandwidth
Phase margin at unity VI = 10 mV, RL = 2 kΩ, gain
V
= 10 V, AVD = –1,
O(PP)
= 2 kΩ,
L
ure 1
See Fi
AVD = –1, 10-V step, RL = 1kΩ, CL = 100 pF
RS = 20 Ω, See Figure 3
VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz V
= 20 V, AVD = 10,
O(PP)
= 1 kHz,
RS = 25 Ω VI = 10 mV, RL = 2 kΩ,
CL = 25 pF, See Figure 2 V
= 20 V, AVD = –1,
O(PP)
RL = 2 kΩ,C
CL = 25 pF, See Figure 2
=
L
To 10 mV
To 1 mV f = 10 Hz
f = 10 kHz f = 10 Hz to
10 kHz
f = 0.1 Hz to
10 Hz
=
L
= 25 pF
L
Full
range
,
25°C 30 45 30 45
Full
range
°
°
°
,
°
°
°
°
TLE2082I TLE2082AI
MIN TYP MAX MIN TYP MAX
–30 –45 –30 –45
30 48 30 48
= ±15 V
CC±
TLE2082I TLE2082AI
MIN TYP MAX MIN TYP MAX
22 22
22 22
0.4 0.4
1.5 1.5 28 28
11.6 11.6
°
°
nV/√Hz
m
V/µs
V/µs
µs
z
z
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
5–13
TLE2082, TLE2082A, TLE2082Y
PARAMETER
TEST CONDITIONS
†
UNIT
VIOI
V
IC O
IIOI
t
VIC 0, VO 0, IIBI
t
5to5to5to5
V
Common mode input R
50 Ω
V
gg
5to5
g
I
200 µA
V
Maximum positive peak I
2 mA
V
I
A
I
200 µA
V
Maximum negative peak I
2 mA
V
I
A
R
600 Ω
A
Large signal differential V
± 2.3 V
R
2 kΩ
R
kΩ
Input
V
0
S
5
F
CMRR
C
VIC V
ICR
min,
dB
k
pp y g j
V
CC±
±5 V to ±15 V,
dB
EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, V
T
A
nput offset voltage
α
r
i
c
z
∗
On products compliant to MIL-STD-883, Class B, this parameter is not production tested.
†
Full range is –55°C to 125°C.
Temperature coefficient
VIO
of input offset voltage
nput offset curren
nput bias curren
Common-mode input
ICR
voltage range
Maximum positive peak
OM+
output voltage swing
Maximum negative peak
OM–
output voltage swing
Large-signal differential
VD
voltage amplification
Input resistance VIC = 0 25°C Input
i
capacitance Open-loop output impedance f = 1 MHz 25°C 80 80 Ω
o
ommon-mode rejection ratio
Supply-voltage rejection ratio
SVR
(∆V
CC±
Common mode Differential
/∆VIO)
VIC = 0, VO = 0, RS= 50Ω
VIC = 0, VO = 0, See Figure 4
=
S
= –
O
= –
O
= –20 m
O
=
O
=
O
= 20 m
O
=
L
=
O
,
=
IC
VIC = V
ICR
VO = 0, RS = 50 Ω V
= ±5 V to ±15 V,
CC±
VO = 0, RS = 50 Ω
min,
=
L
= 10
L
ee Figure
25°C 0.9 7 0.65 4
Full range 9.5 6.5 Full range 2.3 25
25°C 5 100 5 100 pA
Full range 20 20 nA
25°C 15 175 15 175 pA
Full range 60 60 nA
25°C
Full range
25°C 3.8 4.1 3.8 4.1
Full range 3.6 3.6
25°C 3.5 3.9 3.5 3.9
Full range 3.3 3.3
25°C 1.5 2.3 1.5 2.3
Full range 1.4 1.4
25°C –3.8 –4.2 –3.8 –4.2
Full range –3.6 –3.6
25°C –3.5 –4.1 –3.5 –4.1
Full range –3.3 –3.3
25°C –1.5 –2.4 –1.5 –2.4
Full range –1.4 –1.4
25°C 80 91 80 91
Full range 78 78
25°C 90 100 90 100 dB
Full range 88 88
25°C 95 106 95 106
Full range 93 93
25°C 11 11 25°C 2.5 2.5
25°C 70 89 70 89
Full range 68 68
25°C 82 99 82 99
Full range 80 80
= ±5 V (unless otherwise noted)
CC±
TLE2082M TLE2082AM
MIN TYP MAX MIN TYP MAX
∗
5 5 5 5
–1 –1.9 –1 –1.9
5 5
–0.8 –0.8
12
10
2.3 25∗µV/°C
to
to
12
10
m
Ω
p
5–14
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082, TLE2082A, TLE2082Y
PARAMETER
TEST CONDITIONS
†
UNIT
I
Supply current V
No load
A
I
Short circuit output V
0
25°C
A
PARAMETER
TEST CONDITIONS
†
UNIT
A
R
C
L
100 pF,See Figure 1
tsSettli
2 V step,
25°C
V
Equivalent input noise
25°C
S
,
f 10 Hz to
6
6
V
Peak to peak equivalent
25°CµV
f 0.1 Hz to
0.6
0.6
THD
N
Total harmonic f
R
25°C
0.013%
0.013%
B1Unit
idth
VI 10 mV, RL 2 kΩ,
25°C
9.4
9.4
MH
B
Maximum output swing
O(PP)
,
VD
,
25°C
2.8
2.8
MH
φ
gy
I
,
L
,
25°C
56°
56°
EXCALIBUR HIGH-SPEED
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, V (continued)
T
CC
OS
†
Full range is –55°C to 125°C.
Supply current (both channels)
Crosstalk attenuation VIC = 0, RL = 2 kΩ 25°C 120 120 dB Short-circuit output
current
O
O
= 0,
=
VID = 1 V VID = –1 V
A
25°C 2.7 2.9 3.6 2.7 2.9 3.6
Full range 3.6 3.6
°
MIN TYP MAX MIN TYP MAX
operating characteristics at specified free-air temperature, V
T
A
MIN TYP MAX MIN TYP MAX
25°C 35 35
SR+ Positive slew rate
SR– Negative slew rate
ng time
n
N(PP)
I
n
OM
m
∗
On products compliant to MIL-STD-883, Class B, this parameter is not production tested.
†
Full range is –55°C to 125°C.
Equivalent input noise voltage
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
Total harmonic
+
distortion plus noise
y-gain bandw
Maximum output-swing bandwidth
Phase margin at unity VI = 10 mV, RL = 2 kΩ, gain
V
= ±2.3 V ,
O(PP)
–
= –1,
VD
= 100 pF,See Figure 1
=
C
AVD = –1, 2-V step, RL = 1 kΩ, CL = 100 pF
RS = 20 Ω, See Figure 3
VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz V
= 5 V, AVD = 10,
O(PP)
= 1 kHz,
RS = 25 Ω VI = 10 mV, RL = 2 kΩ,
CL = 25 pF, See Figure 2 V
= 4 V, AVD = –1,
O(PP)
RL = 2 kΩ ,C
CL = 25 pF, See Figure 2
= 2 kΩ,
L
To 10 mV
To 1 mV f = 10 Hz
f = 10 kHz f = 10 Hz to
10 kHz
f = 0.1 Hz to
10 Hz
= 2 kΩ,
L
= 25 pF
L
Full
range
25°C 38 38
Full
range
18
18
°
°
°
°
°
°
°
= ±5 V (unless otherwise noted)
CC±
TLE2082M TLE2082AM
–35 –35
45 45
= ±5 V
CC±
TLE2082M TLE2082AM
∗
∗
0.25 0.25
0.4 0.4 28 28
11.6 11.6
°
18
18
∗
∗
°
m
m
V/µs
V/µs
µs
nV/√Hz
z
z
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
5–15
TLE2082, TLE2082A, TLE2082Y
PARAMETER
TEST CONDITIONS
†
UNIT
VIOI
V
IC O
IIOI
t
VIC 0, VO 0, IIBI
t
15to15to15to15
V
Common mode input R
50 Ω
V
gg
15to15
g
I
200 µA
V
Maximum positive peak I
2 mA
V
I
A
I
200 µA
V
Maximum negative peak I
2 mA
V
I
A
R
600 Ω
A
Large signal differential V
± 10 V
R
2 kΩ
dB
R
kΩ
c
i
capacitance
VIC 0, See Figure 5
pF
CMRR
C
VIC V
ICR
min,
dB
k
pp y g j
V
CC±
±5 V to ±15 V,
dB
EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, V
T
A
nput offset voltage
α
r
i
c
z
∗
On products compliant to MIL-STD-883, Class B, this parameter is not production tested.
†
Full range is –55°C to 125°C.
Temperature coefficient
VIO
of input offset voltage
nput offset curren
nput bias curren
Common-mode input
ICR
voltage range
Maximum positive peak
OM+
output voltage swing
Maximum negative peak
OM–
output voltage swing
Large-signal differential
VD
voltage amplification
Input resistance VIC = 0 25°C
Input
i
Open-loop output impedance f = 1 MHz 25°C 80 80 Ω
o
ommon-mode rejection ratio
Supply-voltage rejection ratio
SVR
(∆V
/∆VIO)
CC±
Common mode
Differential
VIC = 0, VO = 0, RS= 50 Ω
VIC = 0, VO = 0, See Figure 4
=
S
= –
O
= –
O
= –20 m
O
=
O
=
O
= 20 m
O
=
L
=
O
VIC = 0, See Figure 5
VIC = V
ICR
VO = 0, RS = 50 Ω V
= ±5 V to ±15 V,
CC±
VO = 0, RS = 50 Ω
min,
=
L
= 10
L
25°C 1.1 7 0.7 4
Full range 9.5 6.5 Full range 2.4 25
25°C 6 100 6 100 pA
Full range 20 20 nA
25°C 20 175 20 175 pA
Full range 65 65 nA
25°C
Full range
25°C 13.8 14.1 13.8 14.1
Full range 13.6 13.6
25°C 13.5 13.9 13.5 13.9
Full range 13.3 13.3
25°C 11.5 12.3 11.5 12.3
Full range 11.4 11.4
25°C –13.8 –14.2 –13.8 –14.2
Full range –13.6 –13.6
25°C –13.5 –14 –13.5 –14
Full range –13.3 –13.3
25°C –11.5 –12.4 –11.5 –12.4
Full range –11.4 –11.4
25°C 80 96 80 96
Full range 78 78
25°C 90 109 90 109
Full range 88 88
25°C 95 118 95 118
Full range 93 93
25°C 7.5 7.5 25°C 2.5 2.5
25°C 80 98 80 98
Full range 78 78
25°C 82 99 82 99
Full range 80 80
= ±15 V (unless otherwise noted)
CC±
TLE2082M TLE2082AM
MIN TYP MAX MIN TYP MAX
∗
15 15 15 15
–11 –11.9 –11 –11.9
15 15
–10.8 –10.8
12
10
2.4 25∗µV/°C
to
to
12
10
m
Ω
pF
5–16
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082, TLE2082A, TLE2082Y
PARAMETER
TEST CONDITIONS
†
UNIT
I
Supply current V
No load
A
Short circuit output
PARAMETER
TEST CONDITIONS
†
UNIT
R
C
100 pF
g
See Figure 1
tsSettli
10 V step,
25°C
V
Equivalent input noise
25°C
S
,
f 10 Hz to
6
6
V
Peak to peak equivalent
25°CµV
f 0.1 Hz to
0.6
0.6
THD
N
Total harmonic distortion f
R
25°C
0.008%
0.008%
B1Unit
idth
VI 10 mV, RL 2 kΩ,
25°C
∗
10
∗
10
MH
B
Maximum output swing
O(PP)
,
VD
,
25°C
∗
∗
kH
φ
gy
I
,
L
,
25°C
57°
57°
EXCALIBUR HIGH-SPEED
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, V
= ±15 V (unless otherwise noted)
CC±
(continued)
T
A
CC
Crosstalk attenuation VIC = 0, RL = 2 kΩ 25°C 120 120 dB
I
OS
†
Full range is –55°C to 125°C.
Supply current (both channels)
Short-circuit output current
= 0,
O
VO = 0
VID = 1 V VID = –1 V
25°C 2.7 3.1 3.6 2.7 3.1 3.6
Full range 3.6 3.6
25°C
operating characteristics at specified free-air temperature, V
T
A
25°C 28 40 28 40
SR+ Positive slew rate
SR– Negative slew rate
ng time
n
N(PP)
I
n
OM
m
∗
On products compliant to MIL-STD-883, Class B, this parameter is not production tested.
†
Full range is –55°C to 125°C.
Equivalent input noise voltage
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
Total harmonic distortion
+
plus noise
y-gain bandw
Maximum output-swing bandwidth
Phase margin at unity VI = 10 mV, RL = 2 kΩ, gain
V
= 10 V, AVD = –1,
O(PP)
= 2 kΩ,
L
ure 1
See Fi
AVD = –1, 10-V step, RL = 1kΩ, CL = 100 pF
RS = 20 Ω, See Figure 3
VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz V
= 20 V, AVD = 10,
O(PP)
= 1 kHz,
RS = 25 Ω VI = 10 mV, RL = 2 kΩ,
CL = 25 pF, See Figure 2 V
= 20 V, AVD = –1,
O(PP)
RL = 2 kΩ,C
CL = 25 pF, See Figure 2
=
L
To 10 mV
To 1 mV f = 10 Hz
f = 10 kHz f = 10 Hz to
10 kHz
f = 0.1 Hz to
10 Hz
= 2 kΩ,
L
= 25 pF
L
Full
range
,
25°C 30 45 30 45
Full
range
°
°
°
°
°
°
°
TLE2082M TLE2082AM
MIN TYP MAX MIN TYP MAX
–30 –45 –30 –45
30 48 30 48
= ±15 V
CC±
TLE2082M TLE2082AM
MIN TYP MAX MIN TYP MAX
20 20
20 20
0.4 0.4
1.5 1.5 28 28
11.6 11.6
∗
8
∗
°
∗
8
∗
°
nV/√Hz
m
mA
V/µs
V/µs
µs
z
z
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
5–17
TLE2082, TLE2082A, TLE2082Y
PARAMETER
TEST CONDITIONS
V
V
S
4
15to15
ICR
pgg
S
OM+
pppgg
OM
gp p g g
VD
gg g p
O
I
V
S
5
F
IOSShort-ci
t
V
0
A
EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
electrical characteristics at V
V I
IO
I
IB
V
V
V
A
r
i
c
z CMRR Common-mode rejection ratio VIC = V
k I
CC
Input offset voltage VIC = 0, VO = 0, RS = 50 Ω 1.1 6 mV
IO
Input offset current Input bias current
Common-mode input voltage range RS = 50 Ω
ICR
Maximum positive peak output voltage swing
OM+
Maximum negative peak output voltage swing
OM–
Large-signal differential voltage amplification VO = ± 10 V
VD
Input resistance VIC = 0
i
o
SVR
nput capacitance
Open-loop output impedance f = 1 MHz 80 Ω
Supply-voltage rejection ratio (∆V Supply current (both channels) VO = 0, No load 2.7 3.1 3.6 mA
rcuit output curren
= ±15 V, TA = 25°C
CC±
Common mode Differential
/∆VIO)
CC±
IC
IO = –200 µA 13.8 14.1 IO = –2 mA 13.5 13.9 IO = –20 mA 11.5 12.3 IO = 200 µA –13.8 –14.2 IO = 2 mA IO = 20 mA –1 1.5 –12.4
= 0,
O
V
CC±
RS = 50 Ω
=
O
TLE2082Y
MIN TYP MAX
= 0,
min, VO = 0, RS = 50 Ω 80 98 dB
ICR
= ±5 V to ±15 V, VO = 0,
= 0,
O
RL = 600 Ω 80 96 RL = 2 kΩ 90 109 RL = 10 kΩ 95 118
ee Figure
VID = 1 V –30 –45 VID = –1 V
ee Figure
20 175 pA
15 15
to
–11 11.9
–13.5 –14
12
10
7.5
2.5
82 99 dB
30 48
UNIT
6 100 pA
V
V
V
dB
Ω
p
m
V
†
Figure 1. Slew-Rate Test Circuit Figure 2. Unity-Gain Bandwidth
5–18

PARAMETER MEASUREMENT INFORMATION

2 kΩ
V
– +
V
CC+
CC–
2 kΩ
I
Includes fixture capacitance
V
O
R
L
†
C
L
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
10 kΩ
V
CC+
100 Ω
V
I
†
Includes fixture capacitance
– +
V
CC–
V
R
L
and Phase-Margin Test Circuit
O
†
C
L
TLE2082, TLE2082A, TLE2082Y
IIBI
t
p
,
EXCALIBUR HIGH-SPEED
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
PARAMETER MEASUREMENT INFORMATION
2 kΩ
V
CC+
– +
R
S
R
V
S
CC–
V
O
Ground Shield
V
CC+
– +
V
Picoammeters
CC–
V
O
Figure 3. Noise-Voltage Test Circuit Figure 4. Input-Bias and Offset-
Current Test Circuit
V
CC+
IN– IN+
C
id
C
ic
– +
C
ic
V
CC–
V
O
Figure 5. Internal Input Capacitance
typical values
Typical values presented in this data sheet represent the median (50% point) of device parametric performance.
input bias and offset current
At the picoampere bias-current level typical of the TLE2082 and TLE2082A, accurate measurement of the bias becomes difficult. Not only does this measurement require a picoammeter , but test socket leakages can easily exceed the actual device bias currents. To accurately measure these small currents, Texas Instruments uses a two-step process. The socket leakage is measured using picoammeters with bias voltages applied but with no device in the socket. The device is then inserted in the socket, and a second test is performed that measures both the socket leakage and the device input bias current. The two measurements are then subtracted algebraically to determine the bias current of the device.
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
V
α
I
V V
IO VIO
IO
ICR ID
Input offset voltage Distribution 6 Temperature coefficient Distribution 7 Input offset current vs Free-air temperature 8, 9
nput bias curren
Common-mode input voltage range vs Free-air temperature 11 Differential input voltage vs Output voltage 12, 13
vs Free-air temperature 8, 9 vs T otal supply voltage
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
5–19
TLE2082, TLE2082A, TLE2082Y
|VOM|
Maxi
p
,
AVDL
diff
lificati
CMRR
C
qy
k
S
qy
vs Supply voltage
30
CC
pp y
p
vs Supply voltage
34
OS
p
p
vs Free air temperature
37, 38
VnI
Gain-bandwidth
t
p
vs Free air temperature
51
φ
m
g
pp y g
EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994

TYPICAL CHARACTERISTICS

Table of Graphs (Continued)
V
OM+
V
OM–
V
O(PP)
V
O
A
VD
SVR
I
CC
I
OS
SR Slew rate
V
n
THD +N Total harmonic distortion plus noise vs Frequency 45, 46 B
1
φ
m
z
o
Maximum positive peak output voltage vs Output current 14 Maximum negative peak output voltage vs Output current 15
mum peak output voltage
Maximum peak-to-peak output voltage vs Frequency 19 Output voltage vs Settling time 20
arge-signal
Small-signal differential voltage amplification vs Frequency 24, 25
ommon-mode rejection ratio
upply-voltage rejection ratio
Supply current
Short-circuit output current
Equivalent input noise voltage vs Frequency 41
nput-referred noise voltage
Third-octave spectral noise density vs Frequency bands 44
Unity-gain bandwidth vs Load capacitance 47
Gain margin vs Load capacitance 50
Phase margin
Phase shift vs Frequency 24, 25 Large-signal pulse response, noninverting vs Time 54 Small-signal pulse response vs Time 55 Closed-loop output impedance vs Frequency 56 Crosstalk attenuation vs Frequency 57
erential voltage amp
produc
vs Free-air temperature 16, 17 vs Supply voltage
vs Load resistance 21
on
vs Free-air temperature 22, 23
vs Frequency 26 vs Free-air temperature 27
vs Frequency 28 vs Free-air temperature 29
vs Supply voltage 30 vs Free-air temperature vs Differential input voltage 32, 33
vs Supply voltage 34 vs Elapsed time vs Free-air temperature 36
vs Free-air temperature 37, 38 vs Load resistance vs Differential input voltage 40
vs Noise bandwidth 42 Over a 10-second time interval 43
vs Free-air temperature 48 vs Supply voltage 49
vs Free-air temperature 51 vs Supply voltage vs Load capacitance 53
FIGURE
18
31
35
39
52
5–20
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082, TLE2082A, TLE2082Y
EXCALIBUR HIGH-SPEED
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
DISTRIBUTION OF TLE2082
INPUT OFFSET VOLTAGE
20
600 Units Tested From One Wafer Lot
18
VCC = ±15 V TA = 25°C
16
P Package
14
12 10
8
6
Percentage of Units – %
4 2 0
– 4 – 2.4 – 0.8 0.8
– 1.6– 3.2 0 1.6 3.2
VIO – Input Offset Voltage – mV
V
IO
TYPICAL CHARACTERISTICS
DISTRIBUTION OF TLE2082 INPUT OFFSET
VOLTAGE TEMPERATURE COEFFICIENT
30
310 Amplifiers VCC = ±15 V
27
TA = – 55°C to 125°C
24
P Package
21
18 15
12
9
Percentage of Amplifiers – %
6 3
2.4 4
0 – 30 – 24 –18 –12 – 6 0 6
†
α
– Temperature Coefficient – µV/°C
VIO
12 18 24 30
Figure 6 Figure 7
INPUT BIAS CURRENT AND
INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
V
= ±5 V
CC±
VIC = 0 VO = 0
10
1
I
0.1
I
0.01
IO
I
0.001
IB
IIB and IIO – Input Bias and Input Offset Currents – nA
I
–75 –55 –35 –15 –5 –75 –55 –35 –15 5
TA – Free-Air Temperature – ° CT
IB
25 45
65 85 105 125
IO
V
CC±
VIC = 0 VO = 0
10
1
0.1
0.01
IO
I
0.001
IB
IIB and IIO – Input Bias and Input Offset Currents – nA
I
INPUT BIAS CURRENT AND
INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
= ±15 V
I
IB
I
IO
25 45 65 85 105 125
– Free-Air Temperature – ° C
A
Figure 8 Figure 9
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
5–21
TLE2082, TLE2082A, TLE2082Y EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
INPUT BIAS CURRENT
6
10
VICmax = V
5
10
4
10
3
10
2
10
IB
IIB – Input Bias Current – pA
I
1
10
0
10
0 5 10 15 20 25 30 35 40 45 VCC – Total Supply Voltage (Referred to V
VICmin
TA = 25°C
TA = –55°C
vs
SUPPLY VOLTAGE
CC+
TA = 125°C
TYPICAL CHARACTERISTICS
COMMON-MODE INPUT VOLTAGE RANGE
V
+0.5
CC+
RS = 50 Ω
V
CC+
V
–0.5
CC+
V
+3.5
CC–
V
+3
CC–
V
+2.5
CC–
IC
V
VIC – Common-Mode Input Voltage Range – V
V
+2
CC–
– 75 –55 – 35 –15
) – V
CC–
†
vs
FREE-AIR TEMPERATURE
52545
TA – Free-Air Temperature – ° C
VICmax
VICmin
65 85 105 125
Figure 10 Figure 11
DIFFERENTIAL INPUT VOLTAGE
OUTPUT VOLTAGE
V
= ±5 V
CC±
VIC = 0
Vµ
– 100
– 200
ID
VID – Differential Input Voltage – uV
V
– 300
– 400
RS = 50Ω TA = 25°C
RL = 10 kΩ
0
RL = 2 kΩ
RL = 600 Ω
– 5 – 4 – 3 – 2 – 10 0 1
VO – Output Voltage – V VO – Output Voltage – V
DIFFERENTIAL INPUT VOLTAGE
vs
vs
OUTPUT VOLTAGE
V
= ±15 V
CC±
VIC = 0
Vµ
RL = 600 Ω RL = 600 Ω
RL = 2 kΩ
RL = 10 kΩ
– 100
– 200
ID
VID – Differential Input Voltage – uV
V
– 300
34
25
– 400
RS = 50Ω TA = 25°C
RL = 10 kΩ
0
RL = 2 kΩ
RL = 600 Ω
– 15 – 10 – 5 50
R
L
= 2 kΩ
RL = 10 kΩ
10 15
Figure 12 Figure 13
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
5–22
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082, TLE2082A, TLE2082Y
EXCALIBUR HIGH-SPEED
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS
MAXIMUM POSITIVE PEAK OUTPUT VOLTAGE
vs
OUTPUT CURRENT
15
13.5 12
10.5
9
7.5
6
4.5
3
1.5
V
= ±15 V
CC±
OM+
VOM – Maximum Positive Peak Output Voltage – V
0
V
0 – 5 –10 –15 – 20 – 25 – 30
IO – Output Current – mA IO – Output Current – mA
TA = 125°C
TA = –55°C
– 35 – 40 – 45 – 50
TA = 25°C
TA = 85°C
–13.5
–10.5
– 9
–7.5
– 6
– 4.5
– 3
– Maximum Negative Peak Output Voltage – V
–1.5
OM –
V
†
MAXIMUM NEGATIVE PEAK OUTPUT VOLTAGE
vs
OUTPUT CURRENT
TA = –55°C
TA = 25°C
TA = 125°C
V
= ±15 V
CC±
0
0 5 10 15 20 25 30
TA = 85°C
35 40 45 50
5 4 3
2
1 0
– 1 – 2
– 3
OM
V
– 4
| | – Maximum Peak Output Voltage – V
– 5
Figure 14 Figure 15
MAXIMUM PEAK OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
IO = –200 µA IO = –2 mA
IO = –20 mA
V
= ±5 V
CC±
IO = 20 mA
IO = 2 mA
IO = 200 µA
52545
TA – Free-Air Temperature – ° CT
65 85 105 125
14.5
13.5
12.5
11.5
OM
V
10.5
| | – Maximum Peak Output Voltage – V
MAXIMUM PEAK OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
15
14
13
12
11
10
IO = –200 µA
IO = –20 mA
V
= ±15 V
CC±
–75 –55 –35 –15–75 –55 –35 –15
– Free-Air Temperature – ° C
A
IO = 200 µA
IO = 2 mA
IO = –2 mA
52545
IO = 20 mA
65 85 105 125
Figure 16 Figure 17
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
5–23
TLE2082, TLE2082A, TLE2082Y EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
MAXIMUM PEAK OUTPUT VOLTAGE
25
TA = 25°C
20 15
10
5 0
– 5
OM
– 20
V
VOM – Maximum Peak Output Voltage – V
– 25
0 2.5 5 7.5 10 12.5 15
IO = –200 µA
IO = 200 µA
|V
CC±
Figure 18 Figure 19
TYPICAL CHARACTERISTICS
vs
SUPPLY VOLTAGE
IO = –20 mA
IO = 20 mA
IO = 2 mA
17.5 20 22.5 25
| – Supply Voltage – V
IO = –2 mA
†
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE
vs
FREQUENCY
30
V
= ±15 V
CC±
25
20
TA = –55°C
15
TA = 25°C,
V
CC±
125°C
= ±5 V
10
5
0
O(PP)
V
VO(PP) – Maximum Peak-to-Peak Output Voltage – V
100 k 1 M 10 M
TA = 25°C, 125°C
TA = –55°C
f – Frequency – Hz
RL = 2 kΩ
OUTPUT VOLTAGE
vs
SETTLING TIME
12.5 10
7.5 5
2.5
0
– 2.5
O
– 5
V
VO – Output Voltage – V
– 7.5
– 10
– 12.5
0 0.5 1 1.5 2
10 mV
Rising
Falling
10 mV
ts – Settling Time – µs
1 mV
V RL = 1 kΩ CL = 100 pF AV = –1 TA = 25°C
1 mV
Figure 20 Figure 21
CC±
= ±15 V
LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION
LOAD RESISTANCE
VIC = 0
Voltage Amplification – dB
VD
AVD – Large-Signal Differential
A
RS = 50Ω TA = 25°C
115
V
= ±15 V
110
95
90
0.1 1 10 100
CC±
RL – Load Resistance – kΩ
vs
V
CC±
= ±5 V
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
5–24
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082, TLE2082A, TLE2082Y
EXCALIBUR HIGH-SPEED
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION
FREE-AIR TEMPERATURE
110 107 104
Voltage Amplification – dB
VD
AVD – Large-Signal Differential
A
RL = 10 kΩ
RL = 2 kΩ
98 95
92
89
86 83 80
–75 – 55 – 35 –15 5 25 45
RL = 600 Ω
V
= ±5 V
CC±
VO = ±2.3 V
TA – Free-Air Temperature – ° C
vs
TYPICAL CHARACTERISTICS
113
97
Voltage Amplification – dB
VD
AVD – Large-Signal Differential
A
93 89
65 85 105 125
85
–75 5 25456585
†
LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION
vs
FREE-AIR TEMPERATURE
V
= ±15 V
RL = 10 kΩ
RL = 2 kΩ
RL = 600 Ω
TA – Free-Air Temperature – ° C
CC±
VO = ±10 V
125105–15– 35– 55
Figure 22 Figure 23
SMALL-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE SHIFT
vs
80
60
40
20
Voltage Amplification – dB
VD
0
AVD – Small-Signal Differential
A
– 20
– 40
1 10 100 1 k 10 k 100 k
FREQUENCY
V RL = 2 kΩ
Gain
f – Frequency – Hz
CL = 100 pF TA = 25°C
= ±15 V
CC±
Phase Shift
1 M 10 M 100 M
0° 20°
40°
60°
80°
100°
Phase Shift
120°
140°
160° 180°
Figure 24
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
5–25
TLE2082, TLE2082A, TLE2082Y EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS
SMALL-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE SHIFT
30
20
10
0
Voltage Amplification – dB
VD
AVD – Small-Signal Differential
A
V
= ±15 V
– 10
– 20
CC±
VIC = 0 RC = 2 kΩ TA = 25°C
1 4 10 40 100
FREQUENCY
CL = 100 pF
f – Frequency – MHz
vs
Phase Shift
CL = 25 pF
Gain
CL = 100 pF
CL = 25 pF
†
80°
100°
120°
140°
Phase Shift
160°
180°
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
V
90
V
= ±5 V
80
70
60 50
40
30
20 10
CMRR – Common-Mode Rejection Ratio – dB
0
10 100 1 k 10 k
CC±
VIC = 0 VO = 0 RS = 50Ω TA = 25°C
f – Frequency – Hz
CC±
100 k 1 M 10 M
= ±15 V
Figure 25
COMMON-MODE REJECTION RATIO
vs
FREE-AIR TEMPERATURE
97 94
91
88 85
82 79
76
VIC = V VO = 0
73
CMRR – Common-Mode Rejection Ratio – dB
RS = 50 Ω
70
– 75 – 55 – 35 –15 5 25 45
min
ICR
TA – Free-Air Temperature – ° C
V
V
CC±
CC±
= ±15 V
= ±5 V
65 85 105 125
Figure 26 Figure 27
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
5–26
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082, TLE2082A, TLE2082Y
EXCALIBUR HIGH-SPEED
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
SUPPLY-VOLTAGE REJECTION RATIO
FREQUENCY
80
60
k
40
20
∆V
CC±
VIC = 0 VO = 0
0
SVR
XXXX – Supply-Voltage Rejection Ratio – dB
k
– 20
RS = 50Ω TA = 25°C
10 100 1 k 10 k 100 k
SVR–
= ±5 V to ±15 V
f – Frequency – Hz
vs
k
TYPICAL CHARACTERISTICS
SVR+
1 M 10 M
†
SUPPLY-VOLTAGE REJECTION RATIO
FREE-AIR TEMPERATURE
96 90
84
78
∆V
= ±5 V to ±15 V
72 66
SVR
XXXX – Supply-Voltage Rejection Ratio – dB
k
60
CC±
VIC = 0 VO = 0 RS = 50Ω
– 75 – 55 – 35 –15 5 25 45
TA – Free-Air Temperature – ° C
vs
k
SVR+
k
SVR–
65 85 105 125
Figure 28 Figure 29
SUPPLY CURRENT
SUPPLY VOLTAGE
4
VIC = 0
3.8
VO = 0 No Load
3.6
3.4
3.2 3
2.8
2.6
CC
ICC – Supply Current – mA
I
2.4
2.2 2
0 2.5 5 7.5 10 12.5 15
TA = 125°C
|V
CC±
vs
TA = 25°C
TA = –55°C
17.5 20 22.5 25
| – Supply Voltage – V
SUPPLY CURRENT
FREE-AIR TEMPERATURE
3.5 VIC = 0
VO = 0
3.4 No Load
3.3
3.2
3.1
3
2.9
2.8
CC
ICC – Supply Current – mA
I
2.7
2.6
2.5
– 75 – 55 – 35 –15 5 25 45
TA – Free-Air Temperature – ° C
V
vs
CC±
V
CC±
= ±15 V
= ±5 V
65 85 105 125
Figure 30 Figure 31
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
5–27
TLE2082, TLE2082A, TLE2082Y EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS
SUPPLY CURRENT
vs
DIFFERENTIAL INPUT VOLTAGE
14
V
CC+
V
12
10
8
6
4
CC
ICC – Supply Current – mA
I
2
0
– 0.5 – 0.25 0 0.25 0.5
CC–
VIC = 4.5 V TA = 25°C Open Loop No Load
Figure 32 Figure 33
SHORT-CIRCUIT OUTPUT CURRENT
vs
SUPPLY VOLTAGE
60 48 36
VID = –1 V
= 5 V = 0
SUPPLY CURRENT
vs
DIFFERENTIAL INPUT VOLTAGE
25
V
CC±
VIC = 0
20
15
10
CC
ICC – Supply Current – mA
I
5
0
–1.5 –1 – 0.5 0 0.5 1 1.5
VID – Differential Input Voltage – VVID – Differential Input Voltage – V
TA = 25°C Open Loop No Load
SHORT-CIRCUIT OUTPUT CURRENT
vs
ELAPSED TIME
50 40 30
VID = –1 V
= ±15 V
24
12
VO = 0
0
TA = 25°C
– 24
– 36
OS
IOS – Short-Circuit Output Current – mA
I
– 48 – 60
0 2.5 5 7.5 10 12.5 15 17.5 20 22.5 25
|V
| – Supply Voltage – V
CC±
Figure 34 Figure 35
5–28
VID = 1 V
OS
IOS – Short-Circuit Output Current – mA
I
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
20
10
0
– 20 – 30
VID = 1 V
– 40 – 50
0 60 120
t – Elapsed Time – s
V
= ±15 V
CC±
VO = 0 TA = 25°C
TLE2082, TLE2082A, TLE2082Y
EXCALIBUR HIGH-SPEED
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
SHORT-CIRCUIT OUTPUT CURRENT
vs
FREE-AIR TEMPERATURE
80 64 48
32
16
0
– 16
– 32
– 48
OS
IOS – Short-Circuit Output Current – mA
– 64
I
VO = 0
– 80
– 75 – 55 – 35 –15 5 25 45
VID = –1 V
VID = 1 V
V
V
V
V
CC±
TYPICAL CHARACTERISTICS
45
= ±15 V
CC±
= ±5 V
CC±
= ±5 V
CC±
= ±15 V
65 85 105 125
43 41
sµV/
39
37 35
33
31
SR – Slew Rate – V/xs
29 27 25
– 75 – 55 – 35 –15 5 25 45
†
SLEW RATE
FREE-AIR TEMPERATURE
V
= ± 5 V
CC±
RL = 2 kΩ CL = 100 pF
TA – Free-Air Temperature – ° CTA – Free-Air Temperature – ° C
vs
SR–
SR+
65 85 105 125
Figure 36 Figure 37
FREE-AIR TEMPERATURE
70
V
= ±15 V
66 62
sµV/
58 54
50 46
42
SR – Slew Rate –
38
34 30
CC±
RL = 2 kΩ CL = 100 pF
– 75 – 55 – 35 –15 5 25 45
TA – Free-Air Temperature – ° C
Figure 38 Figure 39
SLEW RATE
vs
SR–
SR+
65 85 105 125
SLEW RATE
vs
LOAD RESISTANCE
50
Rising Edge
40
30 20
V
V
= ±5 V
10
0
– 20
SR – Slew Rate – sµV/
– 30
– 40
Falling Edge
– 50
100 1 k 10 k 100 k
CC±
VO± = ±2.5 V
RL – Load Resistance – Ω
= ±15 V
CC±
VO± = ±10 V
AV = –1 CL = 100 pF TA = 25°C
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
5–29
TLE2082, TLE2082A, TLE2082Y EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS
SLEW RATE
vs
DIFFERENTIAL INPUT VOLTAGE
50
40
30
Rising Edge
20
V
10
0
– 20
SR – Slew Rate – sµV/
– 30
Falling Edge
– 40
– 50
0.1 0.4 1 4 10 VID – Differential Input Voltage – V
= ±15 V
CC±
VO± = ±10 V (10% – 90%) CL = 100 pF TA = 25°C
AV = –1
AV = 1
AV = –1
AV = 1
Figure 40 Figure 41
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
50
V
Hz
45
nV/
40
35 30 25
20 15
10
5
n
V
Vn – Equivalent Input Noise Voltage –
0
10 100 1 k 10 k
= ±15 V
CC±
VIC = 0 RS = 20 Ω TA = 25°C
f – Frequency – Hz
INPUT-REFERRED NOISE VOLTAGE
vs
NOISE BANDWIDTH
V
= ±15 V
CC±
µV
n
V
Vn – Input-Referred Noise Voltage –
VIC = 0 RS = 20 Ω TA = 25°C
10
Peak-to-Peak
1
0.1
0.01 1 10 100 1 k 10 k
Noise Bandwidth – Hz
Figure 42 Figure 43
RMS
100 k
INPUT-REFERRED NOISE VOLTAGE
OVER A 10-SECOND TIME INTERVAL
1.2 V
= ±15 V
CC±
µ V
V
n
Vn – Input-Referred Noise Voltage –
– 0.3
– 0.6
f = 0.1 to 10 Hz
0.9
TA = 25°C
0.6
0.3
0
0123456
78910
t – Time – s
5–30
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
TYPICAL CHARACTERISTICS
TLE2082, TLE2082A, TLE2082Y
EXCALIBUR HIGH-SPEED
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
THIRD-OCTAVE SPECTRAL NOISE DENSITY
vs
FREQUENCY BANDS
– 75
Start Frequency: 12.5 Hz
– 80
– 85
– 90
– 95
–100
–105
–110
Thrid-Octave Spectral Noise Density – dB
–115
Stop Frequency: 20 kHz V
= ±15 V
CC±
VIC = 0 TA = 25°C
10 15 20 25 30 35
Frequency Bands
Figure 44 Figure 45
40 45
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
FREQUENCY
1
0.1
0.01
THD + N – Total Harmonic Distortion + Noise – %
0.001 10 100 1 k 10 k 100 k
AV = 100, RL = 600 Ω AV = 100, RL = 2 kΩ
AV = 10, RL = 600 Ω
AV = 10, RL = 2 kΩ
V
= ±5 V
CC±
V
= 5 V
O(PP)
TA = 25°C Filter: 10-Hz to 500-kHz Band Pass
f – Frequency – Hz
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
FREQUENCY
1
Filter: 10-Hz to 500-kHz Band Pass V
= ±15 V
CC±
V
= 20 V
O(PP)
TA = 25°C
0.1
0.01
THD + N – Total Harmonic Distortion + Noise – %
0.001
AV = 100, RL = 600 Ω
AV = 100, RL = 2 kΩ
AV = 10, RL = 600 Ω
AV = 10, RL = 2 kΩ
10 100 1 k 10 k 100 k
f – Frequency – Hz
Figure 46 Figure 47
UNITY-GAIN BANDWIDTH
vs
LOAD CAPACITANCE
13
V
= ±15 V
CC±
VIC = 0 VO = 0
12
RL = 2 kΩ TA = 25°C
11
10
9
1
B1 – Unity-Gain Bandwidth – MHzB
8
7
0204060
CL – Load Capacitance – pF
80 100
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
5–31
TLE2082, TLE2082A, TLE2082Y EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
GAIN-BANDWIDTH PRODUCT
FREE-AIR TEMPERATURE
13
12
11
10
V
= ±5 V
9
Gain-Bandwidth Product – MHz
8
7
–75 – 55 – 35 –15 5 25 45
CC±
TA – Free-Air Temperature – ° C
vs
TYPICAL CHARACTERISTICS
f = 100 kHz VIC = 0 VO = 0 RL = 2 kΩ CL = 100 pF
V
= ±15 V
CC±
Gain-Bandwidth Product – MHz
65 85 105 125
†
GAIN-BANDWIDTH PRODUCT
SUPPLY VOLTAGE
13
f = 100 kHz VIC = 0
12
VO = 0 RL = 2 kΩ CL = 100 pF TA = 25°C
11
10
9
8
7
0 5 10 15
V
|VCC + | – Supply Voltage – V
CC ±
vs
20 25
Figure 48 Figure 49
GAIN MARGIN
LOAD CAPACITANCE
10
V
= ±15 V
CC±
VIC = 0 VO = 0
8
RL = 2 kΩ TA = 25°C
6
4
Gain Margin – dB
2
0
0204060
CL – Load Capacitance – pF
vs
80 100
PHASE MARGIN
FREE-AIR TEMPERATURE
90°
VIC = 0
80°
VO = 0 RL = 2 kΩ
70°
60°
50°
V
40°
m
30°
φ
xm – Phase Margin
20°
10°
0°
CC±
–75 – 55 – 35 –15 5 25 45
V
CC±
= ±15 V
V
TA – Free-Air Temperature – ° C
CC±
vs
= ±15 V
V
CC±
= ±5 V
= ±5 V
CL = 100 pF
65 85 105
CL = 25 pF
Figure 50 Figure 51
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
5–32
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082, TLE2082A, TLE2082Y
EXCALIBUR HIGH-SPEED
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS
PHASE MARGIN
vs
SUPPLY VOLTAGE
90°
80°
70°
60°
50°
40°
m
30°
φ
xm – Phase Margin
VIC = 0
20°
VO = 0 RL = 2 kΩ
10°
TA = 25°C
0°
048121620
|V
CC±
CL = 25 pF
CL = 100 pF
| – Supply Voltage – V
†
PHASE MARGIN
vs
LOAD CAPACITANCE
90°
80°
70°
60°
V
50°
V
= ±5 V
40°
m
30°
φ
xm – Phase Margin
V
20°
10°
IC
VO = 0 RL = 2 kΩ TA = 25°C
0°
0 20 40 60 80 100
CC±
= 0
CL – Load Capacitance – pF
CC±
= ±15 V
15
10
5
0
– 5
O
V
VO – Output Voltage – V
– 10
– 15
Figure 52 Figure 53
NONINVERTING LARGE-SIGNAL
PULSE RESPONSE
TA = 25°C,
125°C
TA = –55°C
TA = 25°C,
125°C
V
= ±15 V
CC±
AV = 1 RL = 2 kΩ CL = 100 pF
01
24
t – Time – µs t – Time – µs
3
Figure 54 Figure 55
TA = –55°C
O
V
VO – Output Voltage – mV
5
–100
SMALL-SIGNAL PULSE RESPONSE
50
0
V
= ±15 V
CC±
AV = –1 RL = 2 kΩ CL = 100 pF TA = 25°C
0 0.4 0.8
1.2 1.6
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
5–33
TLE2082, TLE2082A, TLE2082Y EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS
CLOSED-LOOP OUTPUT IMPEDANCE
vs
FREQUENCY
V
= ±15 V
Ω
10
0.1
0.01
o
zo – Closed-Loop Output Impedance – o
z
0.001
CC±
TA = 25°C
1
AV = 100
AV = 10
AV = 1
10 100 1 k 10 k 100 k 1 M
f – Frequency – Hz
Figure 56 Figure 57
10 M
CROSSTALK ATTENUATION
vs
FREQUENCY
80
60
Crosstalk Attenuation – dB
40
20
V
= ±15 V
CC±
VIC = 0 RL = 2 kΩ TA = 25°C
10 100 1 k 10 k 100 k
f – Frequency – Hz
5–34
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
macromodel information
TLE2082, TLE2082A, TLE2082Y
EXCALIBUR HIGH-SPEED
JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994

APPLICATION INFORMATION

Macromodel information provided was derived using
PSpice Parts
model generation software. The Boyle macromodel (see Note 4) and subcircuit in Figure 58 are generated using the TLE2082 typical electrical and operating characteristics at T
= 25°C. Using this information, output simulations of the following key parameters
A
can be generated to a tolerance of 20% (in most cases):
• Maximum positive output voltage swing
• Maximum negative output voltage swing
• Slew rate
• Quiescent power dissipation
• Input bias current
• Open-loop voltage amplification
NOTE 4: G.R. Boyle, B.M. Cohn, D. O. Pederson, and J. E. Solomon, “Macromodeling of Integrated Circuit Operational Amplifiers”,
V
IN–
IN+
of Solid-State Circuits
CC+
RP
2
1
, SC-9, 353 (1974).
RSS ISS
10
DP
J1 J2
11
C1
3
9
+
12
VC
DC
R2
–
53
6
GCM
• Unity-gain frequency
• Common-mode rejection ratio
• Phase margin
• DC output resistance
• AC output resistance
• Short-circuit output current limit
99
EGND
+
–
VB
+
–
GA
C2
FB
7
VLIM
RO2
HLIM
8
90
+
–
DIN
DIP
91
+
–
+
–
IEEE Journal
92
–
VINVIP
+
RD1
V
CC–
.SUBCKT TLE2082 1 2 3 4 5 C1 11 12 2.2E–12 C2 6 7 10.00E–12 DC 5 53 DX DE 54 5 DX DLP 90 91 DX DLN 92 90 DX DP 4 3 DX EGND 99 0 POLY (2) (3,0) (4,0) 0 .5 .5 FB 7 99 POLY (5) VB VC VE VLP + VLN 0 5.607E6 –6E6 6E6 6E6 –6E6 GA 6 0 1 1 12 333.0E–6 GCM 0 6 10 99 7.43E–9 ISS 3 10 DC 400.0E–6 HLIM 90 0 VLIM 1K J1 11 2 10 JX J2 12 1 10 JX
4
RD2
VE
DE
54
+–
Figure 58. Boyle Macromodel and Subcircuit
PSpice
and
Parts
are trademarks of MicroSim Corporation.
RO1
5
OUT
R2 6 9 100.0E3 RD1 4 11 3.003E3 RD2 4 12 3.003E3 R01 8 5 80 R02 7 99 80 RP 3 4 27.30E3 RSS 10 99 500.0E3 VB 9 0 DC 0 VC 3 53 DC 2.20 VE 54 4 DC 2.20 VLIM 7 8 DC 0 VLP 91 0 DC 45 VLN 0 92 DC 45 .MODEL DX D (IS=800.0E–18) .MODEL JX PJF (IS=15.00E–12 BETA=554.5E–6 + VTO= –.6) .ENDS
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
5–35
TLE2082, TLE2082A, TLE2082Y EXCALIBUR HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIERS
SLOS105A – AUGUST 1991 – REVISED AUGUST 1994
5–36
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

IMPORTANT NOTICE

T exas Instruments (TI) reserves the right to make changes to its products or to discontinue any semiconductor product or service without notice, and advises its customers to obtain the latest version of relevant information to verify, before placing orders, that the information being relied on is current.
TI warrants performance of its semiconductor products and related software to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements.
Certain applications using semiconductor products may involve potential risks of death, personal injury, or severe property or environmental damage (“Critical Applications”).
TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS.
Inclusion of TI products in such applications is understood to be fully at the risk of the customer. Use of TI products in such applications requires the written approval of an appropriate TI officer . Questions concerning potential risk applications should be directed to TI through a local SC sales office.
In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or services described herein. Nor does TI warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used.
Copyright 1995, Texas Instruments Incorporated
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use