Texas Instruments SN74ACT574DBLE, SN74ACT574DBR, SN74ACT574DW, SN74ACT574DWR, SN74ACT574N Datasheet
...
SN54ACT574, SN74ACT574
OCTAL D-TYPE EDGE-TRIGGERED FLIP-FLOPS
WITH 3-STATE OUTPUTS
SCAS537C – OCTOBER 1995 – REVISED JANUARY 2000
D
Inputs Are TTL-Voltage Compatible
D
EPIC
(Enhanced-Performance Implanted
CMOS) 1-µm Process
D
Package Options Include Plastic
Small-Outline (DW), Shrink Small-Outline
(DB), and Thin Shrink Small-Outline (PW)
Packages, Ceramic Chip Carriers (FK) and
Flatpacks (W), and Standard Plastic (N) and
Ceramic (J) DIPs
description
These 8-bit flip-flops feature 3-state outputs
designed specifically for driving highly capacitive
or relatively low-impedance loads. The devices
are particularly suitable for implementing buffer
registers, I/O ports, bidirectional bus drivers, and
working registers.
The eight flip-flops of the ’ACT574 devices are
D-type edge-triggered flip-flops. On the positive
transition of the clock (CLK) input, the Q outputs
are set to the logic levels set up at the data (D)
inputs.
A buffered output-enable (OE
to place the eight outputs in either a normal logic
state (high or low logic levels) or the
high-impedance state. In the high-impedance
state, the outputs neither load nor drive the bus
lines significantly. The high-impedance state and
the increased drive provide the capability to drive
bus lines in a bus-organized system without need
for interface or pullup components.
) input can be used
SN54ACT574 ...J OR W PACKAGE
SN74ACT574 . . . DB, DW, N, OR PW PACKAGE
SN54ACT574 . . . FK PACKAGE
3D
4D
5D
6D
7D
(TOP VIEW)
1
OE
2
1D
3
2D
4
3D
5
4D
6
5D
7
6D
8
7D
9
8D
GND
10
(TOP VIEW)
2D1DOE
3212019
4
5
6
7
8
910111213
8D
GND
20
19
18
17
16
15
14
13
12
11
CLK
V
8Q
CC
V
CC
1Q
2Q
3Q
4Q
5Q
6Q
7Q
8Q
CLK
1Q
18
17
16
15
14
7Q
2Q
3Q
4Q
5Q
6Q
OE
does not affect internal operations of the flip-flop. Old data can be retained or new data can be entered while
the outputs are in the high-impedance state.
The SN54ACT574 is characterized for operation over the full military temperature range of –55°C to 125°C. The
SN74ACT574 is characterized for operation from –40°C to 85°C.
FUNCTION TABLE
(each flip-flop)
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
EPIC is a trademark of Texas Instruments Incorporated.
UNLESS OTHERWISE NOTED this document contains PRODUCTION
DATA information current as of publication date. Products conform to
specifications per the terms of Texas Instruments standard warranty.
Production processing does not necessarily include testing of all
parameters.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
INPUTS
OE CLK D
L ↑ H H
L ↑ LL
L H or L X Q
H X X Z
OUTPUT
Q
0
Copyright 2000, Texas Instruments Incorporated
1
SN54ACT574, SN74ACT574
OCTAL D-TYPE EDGE-TRIGGERED FLIP-FLOPS
WITH 3-STATE OUTPUTS
SCAS537C – OCTOBER 1995 – REVISED JANUARY 2000
logic symbol
OE
CLK
1D
2D
3D
4D
5D
6D
7D
8D
†
This symbol is in accordance with ANSI/IEEE Std 91-1984 and
IEC Publication 617-12.
†
1
11
2
3
4
5
6
7
8
9
EN
1D
C1
19
18
17
16
15
14
13
12
logic diagram (positive logic)
1
OE
11
CLK
1Q
2Q
3Q
4Q
5Q
6Q
7Q
8Q
1D
2
To Seven Other Channels
1D
C1
19
1Q
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, VCC –0.5 V to 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage range, VI (see Note 1) –0.5 V to VCC + 0.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output voltage range, V
Input clamp current, IIK (VI < 0 or VI > V
Output clamp current, I
Continuous output current, I
Continuous current through VCC or GND ±200 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package thermal impedance, θJA (see Note 2): DB package 70°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, T
‡
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
2. The package thermal impedance is calculated in accordance with JESD 51.
(see Note 1) –0.5 V to VCC + 0.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
O
(VO < 0 or VO > V
OK
(VO = 0 to VCC) ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
O
±20 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CC)
±20 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CC)
DW package 58°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
N package 69°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PW package 83°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
–65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
stg
‡
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Loading...