Telex TT-16, TR-16 User Manual

Page 1
Telex
Op er at ing In struc tions
RadioCom
Wireless IFB
TT-16
16 Channel Transmitter
TR-16
16 Channel Receiver
Page 2
INTRODUCTION
WHAT IS THE TELEX WIRELESS IFB SYSTEM?
Trans mit ter: The trans mit ter gen er ates and am pli -
fies a RF (Ra dio Fre quency) car rier sig nal, mod u ­lates this car rier with the mi cro phone sig nal, and ra di ates the mod u lated RF car rier.
Re ceiver: The FM VHF re ceiver is tuned to the fre ­quency of the trans mit ter. The re ceiver picks up the ra di ated RF sig nal from the trans mit ter through the an tenna and con verts the RF sig nal into au dio volt ­ages for use with an ear phone, head phone, but ton re ceiver, neckloop, etc. The re ceiver fre quency must be matched to the trans mit ter fre quency.
ANT.
WHAT FREQUENCY BAND DOES THE TELEX SYSTEM OPERATE IN?
The Telex Sys tems fea ture a syn the sized trans mit ter and a syn the sized re ceiv er op er at ing in the VHF Band be tween 64-68 MHz. See Ta ble 1 for stan dard fre quen cies avail able.
Each trans mit ter chan nel can be uti lized by any num ber of re ceiv ers in any given area. Up to five si ­mul ta neous sys tems can be used in a given area.
ANT.
SOUND
SOURCE
TRANSMITTER
Block Di a gram of Typ i cal Wire less IFB Sys tem
RF CARRIER
SIGNAL
Fig ure 1
FM
RECEIVER
EARPHONE
-1-
Page 3
OFTEN ASKED QUESTIONS
Ques tion: Can more than one sys tem be used si -
mul ta neously?
An swer: Yes but never on the same fre quency. You
will need to have dif fer ent fre quen cies for ev ery re ­ceiver/trans mit ter com bi na tion.
Ques tion: Is the sys tem more sen si tive in any one
par tic u lar di rec tion?
An swer: No, the trans mit ter’s an tenna ra di ates
equally in all di rec tions, but the sig nal is at ten u ated by your body, walls or other sur round ing ob jects. The re ceiv ing an tenna is es sen tially sen si tive in all di rec tions as well.
When ever the sys tem is in use, the trans mit ter should be left on to pre vent the re ceiver from pick ­ing up out side in ter fer ence.
Ques tion: What is E.D.R.? An swer: E.D.R. stands for en hanced Dy namic
Range (companded) au dio. E.D.R. im proves the sig ­nal-to-noise ra tio pro vid ing much better au dio qual ­ity.
Ques tion: Can the TT-16 and TR-16 be used with
ex ist ing TR-34 and TT-44 prod ucts.
An swer: Yes, as long as the E.D.R. fea ture is dis -
abled on the TT-16 and TR-16.
AVAILABLE FREQUENCIES
Ques tion: Can the re ceiver re ceive other trans mis -
sions when the trans mit ter is turned off?
An swer: Yes it can. Telex sys tems op er ate in the
VHF Band be tween 64-68 MHz. How ever, it is not sus cep ti ble to ra dio wave skip, CB’ers or stan dard FM ra dio trans mis sions. It is on TV Broad cast chan ­nels 3 and 4. So it is best to use the chan nels in your sys tem that are not on the TV broad cast chan ­nel in your area. See Ta ble 1.
The fre quency your sys tem op er ates on is com puter se lected for least in ter fer ence, but there is no such thing as a 100% clear chan nel all the time.
If the sys tem is go ing to be used in a per ma nent fixed lo ca tion, it should op er ate in ter fer ence free un ­til such a time or date when some one else be gins us ing the same fre quency.
Chan nel Freq. in MHz Broad cast TV
Chan nel
1 64.5 3 2 64.7 3 3 64.9 3 4 65.1 3 5 65.3 3 6 65.5 3 7 65.7 3
8 65.9 3 A 66.1 4 B 66.3 4 C 66.5 4 D 66.7 4 E 66.9 4
F 67.1 4
If the sys tem is go ing to be mov ing among var i ous lo ca tions, you may run into oc ca sional fre quency con flicts.
G 67.3 4 H 67.5 4
Ta ble 1
Fre quen cies Avail able
-2-
Page 4
TR-16 SYNTHESIZED
HEADPHONE JACK
TREBLE CONTROL
RECEIVER
Tre ble Con trol: A push but ton tre ble con trol is pro
vided to en hance higher fre quency au dio when the but ton is en gaged, in di cated by .
-
General Description TR-16
The Telex TR-16 Re ceiver is a com po nent of a sys ­tem which op er ates on six teen (16) user selectable chan nels in the 64 to 68 MHz fre quency band. The re ceiv ers are de signed to be used with the Telex TT-16 Trans mit ter.
Operating Features
Vol ume OFF/ON Con trol: This thumbwheel con -
trol serves as both an off/on switch and as a vol ume con trol. The re ceiver is turned off when the con trol is in the ex treme coun ter-clock wise po si tion, when viewed from the rear, and the vol ume is loud est when the con trol is in the ex treme clock wise po si ­tion.
SET
SWITCH
BUTTON
SET
Head phone Jack: The re ceiver jack ac cepts a
0.140-inch (3.5 mm) di am e ter min ia ture plug. A va ­ri ety of earsets or headphones can be plugged into this jack for lis ten ing.
Belt Clip: The belt clip sup plied is de tach able by spread ing the wire apart at the tops and re mov ing one side of the clip form the case and then the other.
BELT CLIP
TELEX COMMUNICATIONS, INC. MODEL TR-16
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Made in U.S.A.
IC: 1321A-TR16
S.N.: 1001
BATTERY COMPARTMENT
E.D.R.
VOLUME OFF/ON CONTROL
Op er at ing Fea tures TR-16
BELT CLIP
BELT CLIPBELT CLIPBELT CLIP
BATTERY ORIENTATION
BATTERY COMPARTMENT COVER
Fig ure 3
-3-
Page 5
SPEC I FI CA TIONS
TR-16 16 Chan nel Syn the sized Re ceiver
Tem per a ture Range ....................................................................32 to 122 de grees F/0 to +50 de grees C
Sup ply Volt age ...............................................................................................2-3 Volts, (2) AA Bat teries
Bat tery Life ....................................................................................................................20 Hrs - Al ka line
16 Hrs - NimH
8 Hrs - NiCad
Fre quency Re sponse....................................................................................................100-10 kHz ±3 dB
Sen si tiv ity (12 dB SINAD @ 66.1 MHz) ................................................................................1µ V max.
Dis tor tion...............................................................................................................................less than 2%
Au dio Out put @ 10% Dis tor tion
Bat tery In put
Volt age
2.0 V
8 ohm
15 mW
32 ohm 10 mW
3.0 V
80 mW
50 mW
Con trols and Con nec tions.................................................................................Vol ume OFF/ON Switch;
Tre ble Con trol Switch; Chan nel Se lec tion Switch
Au dio Out put Jack
TT-16 SYNTHESIZED TRANSMITTER
General Description
The Telex TT-16 is a base sta tion trans mit ter which op er ates in the 64-68 MHz band and ac cepts a wide range of au dio in put lev els.
Operating Features
TT-16 Front Panel
1. Power But ton (Must be held in for 1
1
6
sec ond to turn off.)
RadioCom
TT-16
WIRELESS IFB TRANSMITTER
2
Monitor
Telex
3
power
set
4
5
Fig ure 4a
Op er at ing Fea tures TT-16 Front Panel
-4-
2. Head phone vol ume ad just ment
3. Head phone Mon i tor ing Jack
4. SET But ton
5. Back Lit LCD Dis play
6. UP and DOWN Ad just ment But tons
Page 6
Balanced
Audio
INPUT
PINS
RTS 1
1-2
RTS 2
1-3
TELEX
2-3
Telex Communications, Inc.
Made in U.S.A.
Unbalanced
Audio
RadioCom
WIRELESS IFB TRANSMITTER
FCC ID: B5DM524
IC: 1321A-TT16
S.N.: XXXXXX
Telex Communications, Inc. Made in USA
TM
TT-16
P/N: 804182
Antenna
12-15V AC/DC
TT-16 Rear Panel
1. XLR In put Con nec tor: Ac cepts bal ­anced two wire Telex, RTS chan nel 1 or RTS chan nel 2. NOTE: RTS chan nel 2 is com pat i ble with *Clear-Com® In ter com Sys tems.
2. Un bal anced Au dio ¼" In put Con ­nec tor.
3. An tenna Jack: Ac cepts tele scop ing an tenna (sup plied).
1
2
3
4
Fig ure 4b
Op er at ing Fea tures TT-16 Rear Panel
9
RF POWER: HIGH
8
+3
0
AUDIO LEVEL dB-36
MHz
UNBALANCED
+6
AUDIO LEVEL
BALANCED
RTS 1 RTS 2 TELEX
EDR
4
2
1
CHANNEL
-10
-5
AUDIO LEVEL
65.9
FREQ.
3
4. Power In put Jack: Ac cepts any source of 12-15 VAC/DC 300 mA min i mum.
5
-30 Bd
6
7
8
1. Chan nel In di ca tor
2. Au dio In put Me ter
3. Fre quency In di ca tor
4. En hanced Dy namic Range In di ca tor
5. RF Trans mit Power (High when lit, Norm when not)
Fig ure 5
LCD Dis play Func tions
6. Un bal anced Au dio Level
7. Bal anced Au dio Level
8. Bal anced In put Se lec tion for RTS 1, RTS 2, Telex
9. Lock Out In di ca tor
*Clear-Com® is a reg is tered trade mark of Clear-Com In ter com Sys tems, Inc.
-5-
Page 7
TT-16 Spec i fi ca tions
Au dio In put: Fe male XLR
RTS 1 Se lected........................................................................Line im ped ance 200 / Level ad just able
RTS 2 Se lected........................................................................Line im ped ance 200 / Level ad just able
Telex Se lected.........................................................................Line im ped ance 300 / Level ad just able
Un bal anced Au dio In put ..................................10K in put im ped ance/10 mV-1.0 VRMS in put range
RF Power Switch.......................................................................50mW in “Hi”, approx. 5mW in “Low”
AGC Range ......................................................................................................................................30 dB
Sig nal-to-noise Ra tio:
Nor mal..........................................................................................................................................58 dB
EDR En abled................................................................................................................................77 dB
Pre-Em pha sis....................................................................................................................................115µS
Max i mum De vi a tion.....................................................................................................................±25 kHz
Fre quency Con trol Crys tal.........................................................................................+/-.005% tol er ance
Avail able Fre quen cies ................................................................................................See Ta ble 1, page 2
Max. Trans mit ter Out put Power....................................................................................................50 mW
Power Re quire ments ................................................................................12-15V, AC or DC @ 300 mA
Di men sions...................................................................................................7 ½"W x 1 3/4"H x 6 7/8"D
FCC ID ......................................................................................................................................B5DM524
EQUIP MENT SET-UP AND OPERATION
TT-16 SYNTHESIZED TRANSMITTER
UN PACKING: Un pack your Wire less IFB sys tem. If
there are any dam ages or short ages, re fer to the "War ­ranty Ser vice In for ma tion" card.
TT-16 TRANS MITTER LO CA TION: Se lect a suit ­able lo ca tion for the TT-16 Trans mit ter. Try to keep a clear, un ob structed path be tween the trans mit ter and re ceiver and al low plenty of free space around the trans mit ter an tenna.
AN TENNA CON NEC TIONS: Con nect the tele ­scop ing an tenna to the rear panel AN TENNA jack.
For best re sults, the an tenna should be ver ti cally aligned. Tighten the knurled ring to hold the an tenna in place, and ex tend the an tenna to full length.
ANTENNA
REAR PANEL
Fig ure 6
An tenna Connection
POWER CON NEC TION: Plug the AC power
adapter into an elec tri cal out let. Plug the other end of the cord into the power in put jack on the rear panel of the TT-16.
-6-
Page 8
Antenna
12-15V AC/DC
-
+
Fig ure 7
Con necting Power
SYSTEM SET UP
All of the chan nel and in put se lec tion func tions are ac cessed from the front panel. Press SET but ton once to be gin Sys tem Setup. When ever a func tion is flash ing, the UP and DOWN but tons can be used to ad just it. Once set, the next func tion will start to flash. To ac cess a spe cific func tion, press SET un til the func tion is flash ing, the fea tures are ac cessed in the fol low ing or der:
Chan nel RF Power Output Un bal anced Level Adjust Bal anced In put (RTS1/RTS2/Telex) Bal anced Level Adjust
should be used for small to me dium sized ven ues and when ever mul ti ple sys tems are be ing used. Press SET when the power is set and the Un bal anced In ­put level will flash.
Un bal anced In put And Level Ad just ment
If the un bal anced au dio in put will not be used, with the "Un bal anced Au dio Level" flash ing use the DOWN but ton to set the level to OFF and press set to go to Bal ance In put Se lec tion.
If the Un bal anced in put will be used, con nect the in ­put now and ap ply au dio con tent. With the au dio con tent play ing and "Un bal anced Au dio Level" flash ing, watch the au dio me ter. The peak sig nal should not go above the 0 dB seg ment, use the UP and DOWN but tons to ad just the in put level so that the loud est in put lights up the 0 dB seg ment. When the level is set, press the SET but ton and one of the in put op tions will flash.
Bal anced In ter com In put and Level Ad just ment
With the Bal anced In ter com In put se lec tion flash ing (RTS1, RTS2, or TELEX). Use the UP and DOWN but tons to scroll to the cor rect in put. With the cor ­rect in put dis played, press SET and the "Bal anced
Au dio Level" in di ca tor will flash.
Chan nel Se lec tion
Turn the TT-16 on by touch ing the POWER but ton. (The TT-16 is de signed to re turn to "on" if power is dis con nected while the unit is on. This is so the unit can be switched on and off with a power strip or rack power).
The LCD dis play will light up and show the Chan ­nel, Au dio Me ter, Fre quency (and E.D.R. if it has been en abled). Press the SET but ton once and Chan ­nel let ter will flash. Use the UP and DOWN Ar row but tons to se lect the de sired chan nel 1-9 and A-H. Press SET when the de sired chan nel is dis played and the chan nel is set. The chan nel let ter will stop flash ing and the RF Power in di ca tor will flash.
RF Power Se lec tion
While the "RF Power" in di ca tor is flash ing, press the UP AR ROW for HIGH and DOWN for NORM (the "RF Power" line will flash quickly and will dis ap pear when SET is pressed). NORM power
If the in ter com au dio in put will not be used, with one of the Bal anced In put op tions flash ing press SET so the "Bal anced Au dio Level" is flash ing. Use the DOWN but ton to set the level to OFF and press SET to end the setup ses sion. When OFF is se lected "Bal anced Au dio Level" will not be dis ­played on the screen.
If the Bal anced In put Se lec tion will be used, then con nect the in put and ap ply au dio con tent. With the au dio con tent play ing and "Bal anced Au dio Level" flash ing, watch the au dio me ter. The peak sig nal should not go above the 0 dB seg ment, use the UP and DOWN but tons to ad just the in put level so that the loud est in put lights up the 0 dB seg ment. When the level is set, press the SET but ton and the Setup Ses sion will end.
NOTE: The TT-16 will op er ate with both Un bal ­anced and Bal anced in puts ac tive at the same time.
-7-
Page 9
En hanced Dy namic Range (E.D.R.) Op er a tion
The Telex TT-16 Trans mit ter is equipped with E.D.R., En hanced Dy namic Range (companded) au ­dio. This mode greatly im proves the Au dio Sig nal to Noise Ra tio when used with the Telex Model TR-16 re ceiver. The E.D.R. mode must be se lected on both the trans mit ter and re ceiver to be ef fec tive. If us ing the TT-16 with TR-34 IFB units, E.D.R. must be turned off.
1) To en gage the E.D.R. func tion, turn the TT-16 off with the power switch. (The power switch must be held for 1 sec ond to turn unit off.)
2) Press and hold the SET but ton while you turn the TT-16 back on. The E.D.R. sym bol will be dis ­played in the lower right cor ner to in di cate the mode is ac tive.
3) Re peat the pro ce dure to dis able the E.D.R func ­tion.
Lock Out
The TT-16 SET but ton can be locked to pre vent E.D.R. ac ti va tion, and un in tended chan nel changes.
1) To en gage the Lock Out Fea ture, press the UP and DOWN but tons at the same time and hold them down for two sec onds.
2) The pad lock sym bol will ap pear and the set but ­ton is dis abled.
3) To un lock the sys tem, press the UP and DOWN but tons and hold them for two sec onds or un til the pad lock sym bol dis ap pears.
MUL TI PLE SYS TEM IN STAL LA TIONS: As with any ra dio de vice, in ter fer ence can oc cur at any time. The fre quen cies of fered are shared with other le git i mate us ers. The se ver ity of in ter fer ence var ies with the dis tance to the in ter fer ing sta tion. Mul ti ple sys tems fur ther com pli cate in stal la tions. The fol low ­ing steps are sug gested in or der to achieve best re sults in your in stal la tion.
1. In or der to de ter mine whether your se lected fre ­quen cies have min i mum in ter fer ence, Telex rec ­om mends that you first tem po rarily in stall the re ceiv ers in your pro posed set ting and mon i tor the chan nel for in ter fer ence. To do this (with fresh bat ter ies in stalled) turn on your re ceiver, but DO NOT turn on any other re ceiver or trans ­mit ter at this time. If audible in ter fer ence is pres ­ent, this may in di cat e an other user on the chan nel. Mon i tor ing should be re peated for each chan nel that you pro pose to use. DO NOT use chan nels that have in ter fer ence.
2. Set your trans mit ter(s) to chan nels with no or min i mum in ter fer ence. Each trans mit ter must be set to a sep a rate fre quency. For best re sults when us ing mul ti ple trans mit ters, each trans mit ter should be in stalled sep a rately as far as pos si ble from the oth ers.
3. Turn on the trans mit ter(s) with an ac tive au dio in put. Test walk a re ceiver through the ex pected lis ten ing area to ver ify cov er age. The sys tem should now be ready for use.
-
Au dio Mon i tor
Turn the Mon i tor (vol ume) con trol all the way down (coun ter clock wise). Af ter the au dio in put lev els have been ad justed, Ste reo head phones with a 3.5 mm or ¼ in. plug can be plugged into the Mon i tor jack. If you wish to mon i tor the au dio pro gram ma ­te rial, turn up the mon i tor (vol ume) con trol to the de sired level. The mon i tor con trol does not af fect the trans mit ted au dio level.
-8-
Page 10
TR-16 SYNTHESIZED RECEIVER
Keep a clear, un ob structed path be tween the trans ­mit ter and re ceiver an ten nas for a clear trans mis ­sion.
1
2
3
E.D.R.
E.D.R.
4
1. Chan nel Dis play 1-9 through A-H and low bat tery in di ca tor
2. Lock In di ca tor (see Change Lock Out)
3. High Fre quency Em pha sis In di ca tor (on when sym bol is show ing)
4. En hanced Dy namic Range In di ca tor.
1) To en gage the E.D.R func tion turn the TR-16 off with the vol ume con trol thumb wheel.
2) Press and hold the SET but ton while you turn the TR-16 back on. The E.D.R. sym bol will be dis ­played in the lower right cor ner to in di cate the mode is ac tive.
3) Re peat the pro ce dure to dis able the E.D.R. func ­tion.
Lock Out
The TR-16 SET but ton can be locked to pre vent E.D.R. ac ti va tion, and un in tended chan nel changes. The High Fre quency Em pha sis but ton will re main ac tive at all times for the con ve nience of the user.
1) To en gage the Lock Out Fea ture, press the SET and but tons at the same time and hold them down for 5 seconds.
2) The pad lock symbol will ap pear and the set but ­ton is dis abled.
3) To un lock the sys tem, press the SET and but ­tons and hold them for 5 sec onds or un til the pad lock symbol dis ap pears.
Fig ure 8
TR-16 Dis play
Chan nel Se lec tion
1) Turn the re ceiver on. A chan nel let ter will show in the dis play.
2) Press the SET but ton once and the Chan nel in di ­ca tor will flash.
3) Press the but ton and the Chan nel will scroll up, match the chan nel to the trans mit ter channel be ing used (TT-16, TT-44).
4) Press SET, the chan nel in di ca tor will stop flash ­ing and the chan nel is set.
En hanced Dy namic Range (E.D.R.) Op er a tion
The Telex TT-16 trans mit ter is equipped with E.D.R., En hanced Dy namic Range (companded) au ­dio. This mode greatly im proves the Au dio Sig nal to Noise Ra tio when used with the Telex Model TR-16 re ceiver. The E.D.R. mode must be se lected on both the trans mit ter and re ceiver to be ef fec tive. If us ing the TR-16 with a TT-44 IFB Trans mit ter, E.D.R. must be turned off.
HEADPHONE JACK
SET
SWITCH
BUTTON
TREBLE CONTROL
SET
E.D.R.
VOLUME OFF/ON CONTROL
-9-
Page 11
Low Bat tery In di ca tion
1) When there is ap prox i mately 10% of the bat tery life left, an animated bat tery sym bol will flash al ter nately with the chan nel let ter in the LCD dis ­play.
2) When there is only 5% bat tery life left, the bat ­tery sym bol will con stantly flash in the dis play.
E.D.R.E.D.R.
-
Low Bat tery Dis play
BATTERY REPLACEMENT
The TR-16 Re ceiver uses two (2) AA bat ter ies. When the bat ter ies are low the sound will be dis ­torted. Re place weak bat ter ies with two fresh AA bat ter ies, and po si tion them in the bat tery com part ­ment as il lus trated in Fig ure 9.
BELT CLIP
BELT CLIPBELT CLIPBELT CLIP
For ad di tional in for ma tion re fer to the “Bat tery In ­for ma tion” Sec tion.
NOTE: If the unit is to be stored for any length of time make sure you re move the bat ter ies from the unit.
BATTERY ORIENTATION
BATTERY COMPARTMENT COVER
Fig ure 9
Bat tery In stal la tion - TR-16
-10-
Page 12
BATTERY INFORMATION
General
Im proper bat tery se lec tion, use, in stal la tion and care are the cause of nu mer ous wire less sys tem fail ures.
ANTENNA INFORMATION
Antenna Alignment
Alkaline Batteries
Al ka line bat ter ies such as Mallory’s DURACELL® or Eveready’s EN ER GIZER® pro vide the most re li ­able op er a tion in wire less trans mit ters and re ceiv ers. The use of low cost car bon-zinc bat ter ies is NOT REC OM MENDED.
*EN ER GIZER® is a reg is tered trade mark of Un ion Car bide Cor po ra tion. *DURACELL® is a reg is tered trade mark of Duracell Inc.
Antenna Placement
Proper an tenna place ment prob a bly has the most ef ­fect on your TELEX Wire less Sys tem’s over all per ­for mance. Fol low ing the sug ges tions that fol low should re sult in “drop out free” per for mance.
Balanced
Audio
INPUT PINS RTS CH1 RTS CH2 TELEX
Telex Communications, Inc.
Made in U.S.A.
1-2 1-3 2-3
Unbalanced
Audio
RadioCom
TT-16
WIRELESS IFB TRANSMITTER
FCC ID: B5DM524
IC: 1321A-TT16
S.N.: XXXXXX
Telex Communications, Inc. Made in USA
TM
12-15V AC/DC
P/N: 804182
An tenna Align ment
Balanced
Audio
INPUT PINS RTS CH1 RTS CH2 TELEX
Telex Communications, Inc.
Made in U.S.A.
Fig ure 10
TM
Antenna
RadioCom
1-2
Unbalanced
1-3
Audio
TT-16
2-3
WIRELESS IFB TRANSMITTER
FCC ID: B5DM524
IC: 1321A-TT16
S.N.: XXXXXX
Telex Communications, Inc. Made in USA
12-15V AC/DC
P/N: 804182
Telex
RadioCom
power
Monitor
TT-16
set
WIRELESS IFB TRANSMITTER
Telex
RadioCom
power
Monitor
TT-16
set
WIRELESS IFB TRANSMITTER
Good and Bad
Fig ure 11
Dis tance Be tween Trans mit ter and Re ceiver
Keep the dis tance be tween the trans mit ter and the re ceiver(s) as short as pos si ble. The greater the dis ­tance the weaker the sig nal.
-11-
Page 13
Make sure the “sig nal path” be tween the trans mit ter and re ceiver(s) is un ob structed. You should al ways be able to vi su ally lo cate the an tenna of the trans ­mit ter at all times.
DO NOT - Mount the trans mit ter on, or next to, metal such as beams, walls with metal studs, etc. This will “de tune” the trans mit ter an tenna which can re sult in loss of sig nal at the re ceiver.
LOCATION IS OK
TM
Telex
RadioCom
power
Monitor
TT-16
set
WIRELESS IFB TRANSMITTER
Telex
RadioCom
power
Monitor
TT-16
WIRELESS IFB TRANSMITTER
set
SIG NAL REACHES AN TENNA AT FULL STRENGTH WITH NO OB ­STRUC TIONS.
Fig ure 12
Keeping Site Clear to An tenna
At tempting to op er ate the sound en hance ment sys ­tem through or around walls, ceil ings, metal ob jects, etc., will re duce sys tem range and per for mance.
RadioCom
TT-16
WIRELESS IFB TRANSMITTER
TM
Telex
power
Monitor
set
LOCATION
IS BAD
T
elex
Fig ure 14
Trans mit ter An tenna Place ment
Telex
RadioCom
power
Monitor
TT-16
set
WIRELESS IFB TRANSMITTER
SIG NAL RE FLEC TION OFF A METAL OB STRUC TION CAUSES RE DUCED SIG NAL AND “MULTIPATH”
Fig ure 13
Op er ating Through Ob struc tion
-12-
Page 14
TROUBLESHOOTING
Re read the sec tions of this man ual to make sure you have com pleted sys tem set-up prop erly.
PROB LEM
DIS TOR TION -Sys tem's au dio qual ity seems
dis torted at me dium to high in put lev els HISS - Sys tem seems to pro duce a "hiss" which
is un de sir able.
DROP OUTS - When mov ing around the area in which you will be us ing the sys tem there seem to be lo ca tions where the sig nal "swooshes" or com pletely dis ap pears.
IN TER FER ENCE - Sys tem picks up sig nals other than the TT-16 Trans mit ter.
If you are un able to solve the prob lem, con tact the dealer from whom you pur chased the sys tem for as ­sis tance.
SO LU TION
Re duce au dio gain on trans mit ter by ad just ing the gain con trols.
Check the gain set tings on the trans mit ter and the vol ume con trol on the re ceiver. They may be too low.
Make sure the an tenna is con nected and fully ex tended. Fol low the lo ca tion sug ges tions on page 15. Change the lo ca tion of the trans mit ter an tenna or avoid the bad area with the re ceiv ers.
Make sure the Telex TT-16 is turned on - this will usu ally elim i nate the in ter fer ence sig nal.
If prob lem per sist with the trans mit ter "ON", try chang ing to an other chan nel.
RE DUCED DIS TANCE - Sys tem does n't op er ­ate as far as it once did. Sys tem does n't' op er ate as well as you think it should.
BAT TER IES DON'T LAST
HUM - Au dio Sys tem emits hum or buzz thru
speak ers and sound en hance ment re ceiver.
Trans mis sion sounds com pressed on TR-16 E.D.R. func tion may be en gaged on the TT-16.
SET but ton does not work, can not change chan ­nel
Re ceiver Bat tery is pos si bly in need of re place ­ment. Trans mit ter an tenna pos si ble lo cated in ­cor rectly. Re ceiver not tuned prop erly.
If us ing "throw away" bat ter ies make sure they are al ka line. If us ing nickel-cad mium or nickel metal hy dride bat ter ies make sure they were fully charged when yo are us ing them and fully drained when you are done be fore re charg ing them.
Lo cate Trans mit ter away from the au dio equip ­ment.
See set ting E.D.R. func tion on page 9. The E.D.R. fea ture can only be used with the TR-16 and must be ac tive on both trans mit ter and re ­ceiver to be ef fec tive.
Lock Out is en gaged, press and hold UP and DOWN but tons un til the pad lock sym bol dis ap ­pears.
-13-
Page 15
FCC INFORMATION
The Telex TR-16 re ceiver is au tho rized un der part 15 of the FCC Reg u la tions. Changes or mod i fi ca ­tions to this equip ment could void the user’s au thor ity to op er ate the equip ment.
The Telex Model TT-16 trans mit ter is au tho rized un der Fed eral Com mu ni ca tions Com mis sion and In dus try Can ada Rules. Li cens ing of the Trans mit ter, if re quired, is the us ers re spon si bil ity and licensability de pends upon the us ers clas si fi ca tion, and fre quency se lected.
CAU TION: Changes or mod i fi ca tions made by the user could void the user's au thor ity to op er ate the equip ment.
Op er a tion is sub ject to the fol low ing two con di tions: (1) This de vice may not cause in ter fer ence, and (2) This de vice must ac cept any in ter fer ence, in clud ing in ter fer ence that may cause un de sired op er a ­tion of the de vice.
ACCESSORIES
CES-2 com plete TeleThin® An nouncer Earset.........................................................................800318000
(incluces TRV-04 125 ohm TeleThin® Re ceiver, CMT-98 5ft TeleThin® Grey cordset and ET-4 Coiled Eartube)
SEB-1 Sin gle Earbud with Cord..................................................................................................59840005
DEB-2 Dual Earbud with Cord....................................................................................................59840001
HED-2 Col laps ible Light weight Head phone...............................................................................59840007
HED-3 Full Cush ion Noise Re duc tion Head phone.....................................................................63510021
TW-A 1/4 Wave Tele scop ing An tenna for TT-16 ...........................................................................877960
PA-2 USA Power Sup ply for TT-16 ................................................................................................730139
RM-S Sin gle Rack Mount for TT-16..........................................................................................71081001
RM-D Dual Rack Mount for TT-16.............................................................................................71081002
TR-16 Belt Clip ................................................................................................................................358815
-14-
Page 16
TELEX COM MU NI CA TIONS, INC. 12000 Port land Ave. South, Bur nsville, MN 55337, U.S.A.
PN 804184 Rev. B AUG 2005 Made in U.S.A.
Loading...