Telex tr-200p, tr-200 User Manual

Download

Telex

Operating Instructions



RadioCom

MODEL TR-200, TR-200P WIRELESS BELT-PACK TRANSCEIVER

Table of Contents

Page

INTRODUCTION .......................................................................................................1

General Description ...............................................................................................1

Block Diagram...................................................................................................2

TECHNICAL INFORMATION ..................................................................................3

Controls and Connections......................................................................................3

Features..................................................................................................................4

Volume ON/OFF Control..................................................................................4

Low Battery and Over Modulation Indicator LED ......................................... 4

Push-To-Talk/Lock-To-Talk Switch .................................................................5

Transmit LED Indicator ....................................................................................5

Headset Jack ......................................................................................................5

Belt Clip.............................................................................................................5

Microphone Gain Control..................................................................................5

Dynamic/Electret Switch ...................................................................................5

Battery Compartment.........................................................................................5

SPECIFICATIONS ......................................................................................................6

SET-UP........................................................................................................................7

Unpacking..............................................................................................................7

Headset Connection ...............................................................................................7

Dynamic/Electret Switch .......................................................................................7

Battery Installation.................................................................................................8

Battery Check ........................................................................................................9

Battery Removal ....................................................................................................9

Dressing the Unit.................................................................................................10

OPERATION .............................................................................................................11

Power ...................................................................................................................11

Push-to-Talk/Lock-to-Talk Switch ......................................................................11

Adjusting Microphone Gain ................................................................................12

BATTERY INFORMATION.....................................................................................13

General.................................................................................................................13

Alkaline Batteries ............................................................................................13

Nickel-Cadmium Batteries ..............................................................................13

BC-4 Battery Charger......................................................................................13

FCC INFORMATION ...............................................................................................14

RECOMMENDED HEADSETS...............................................................................14

ACCESSORIES.........................................................................................................17

WARRANTY SERVICE INFORMATION...............................................................20

-i-

INTRODUCTION

General Description

The Telex Model’s TR-200 and TR-200P Belt-pack Transceivers, are designed with one transmit and one receive channel and will operate on selected frequencies within the 150 to 216 MHz band.

The TR-200 Transceiver operates in the continuous transmit mode with the audio, or talk, activated by a switch. As many as four TR-200 belt-pack transceivers can operate in a fully duplex network with one Telex Model BTR-200 or BTR-200 II Base Station.

The TR-200P Transceiver operates in the Push-to-Transmit mode (the transmit and talk function are activated together). Any number of TR-200P transceivers can be used in a half-duplex network with one BTR-200 or BTR-200 II Base Station. Operate only one transmitter at a time. Attempting to use two transmitters simultaneously on the same channel will cause interference.

Both the TR-200 and TR-200P can be configured to operate with another TR-200 or TR-200P.

The receiver portion of the TR-200 and TR-200P consists of a crystal controlled dual conversion superheterodyne design.

The transmitter portion of the TR-200 and TR-200P consists of a crystal controlled multiplier/amplifier design.

-1-

Figure 1

Block Diagram of TR-200 Transceiver

-2-

TECHNICAL INFORMATION

Controls and Connections

LOW BATTERY / OVERMODULATION INDICATOR LED

TALK INDICATOR LED

PUSH-TO-TALK/ LOCK-TO-TALK SWITCH

BELT CLIP

HEADSET JACK

External controls and Connections

VOLUME ON/OFF CONTROL

RECEIVE ANTENNA

TRANSMIT ANTENNA

Figure 2

-3-

DYNAMIC / ELECTRET SWITCH

FCC ID: B5DTR200 S/N: P/N:70681-

BATTERY COMPARTMENT

Internal Controls

ACCESS TO MICROPHONE GAIN CONTROL

Figure 3

Features

Volume ON/OFF Control: This thumbwheel control serves as both an on/off

switch and as a volume control. The transceiver is turned off when the control is in the extreme counterclockwise position, when viewed from the front, and the volume is loudest when the control is in the extreme clockwise position.

Low Battery and Over Modulation Indicator LED: (labeled “bat/ovmod”)

Low Battery Indicator: Part of the battery check circuit. When the volume

ON/OFF Control is placed in the “ON” position the LED will flash one time if the battery is good. A poor battery will cause the LED to illuminate continuously and a bad or unusable battery will not cause any illumination at all.

Over Modulation Indicator: Uses the same LED as the low battery indicator. During the transmit mode if microphone gain is too high the LED will illuminate when talking. Adjust microphone gain.

-4-

Push-to-Talk/Lock-to-Talk Switch:

For Model TR-200, this switch enables the talk function. Press the button

and hold down as long as required (Push-to-talk function), or if continuous talk is required (lock-to-talk function), quickly press the button two times to lock on. To release the talk function, press the button one time.

For Model TR-200P, this switch enables the transmit and audio function and operates as described for TR-200.

Transmit LED Indicator: (Labeled “talk”) Will be illuminated whenever the transmit function is enabled.

Headset Jack: 4 Pin XLR Connector for Input/Output. The headset jack will accept 5 different Telex Model headsets and 1 handset. See Recommended Headsets starting on Page 14.

MICROPHONE SHIELD (-)

HEADPHONE BALANCED AUDIO OUT

MALE CONNECTORS

BTR-200/TR-200

MICROPHONE AUDIO (+)

Figure 4

Headset Jack Wiring

Belt Clip: Combination Belt Clip/Battery Cover. Access to Battery Compartment,

Microphone Gain Control and Dynamic/Electret Switch is accomplished by removal of belt clip via a quick release 1/4 turn fastener.(See Page 8)

Microphone Gain Control: Screwdriver adjustable by removing belt clip and prying out the small rubber plug to the right of the screw boss. Adjust the gain control clockwise to increase microphone gain or counterclockwise to decrease microphone gain. Replace rubber plug.

Dynamic/Electret Switch: Place switch towards “D” when using a Dynamic Microphone or “E” when using an Electret Microphone.

NOTE: All Telex headsets used with this intercom are dynamic microphones. Unit is shipped in the “D” position.

Battery Compartment: Holds 6 AA batteries in a removable battery holder.

-5-

SPECIFICATIONS

Overall

Power Requirements....................6 AA cells (Alkaline, NEDA, MN 1500)

Nickel Cadmium Optional

Current Drain..........................................................................typical 65 mA

Temperature Range......................................-4°Fto130°F (-20°Cto55°C)

Dimensions.....................................................4.25" W x 4.125" H x 2.0" D

(108mm x 105mm x 51mm)

Weight ................................................................13 oz (369g) with batteries

Transmit Antenna..................................................1/4-wave wire (attached)

Receive Antenna....................................................1/4-wave wire (attached)

Transmit

RF Frequency Range ..............................................................150-216 MHz

RF Frequency Stability .....................................Crystal Controlled, 0.005%

RF Power Output..................................................................50 mW Typical

Modulation..............................................................FM, 5000 Hz deviation,

100 micro-seconds Pre-emphasis

Modulation Limiter.......................................................Internal Compressor

Modulation Frequency Range ................................300 to 5000 Hz +/-2 dB

Microphone Audio Input....................................................30 to 3500 ohms

Microphone Input Sensitivity......................2 mV Dynamic, 4 mV Electret

Radiated Harmonics and Spurious Emissions................................-45 dBC,

Exceeds FCC Specifications

FCC Acceptance ..............................Type Accepted Under Parts 90 and 74

Receive

RF Frequency Range ..............................................................150-216 MHz

RF Frequency Stability .....................................Crystal Controlled, 0.005%

Type ................................................Dual Conversion Superheterodyne, FM

RF Sensitivity......................................Less than 0.5 µV for 12 dB SINAD

IF Selectivity .............................................3 dB at 30 kHz (Ceramic Filter)

Image Rejection ....................................................................70 dB or better

Squelch Quieting..................................................................................90 dB

Squelch Threshold..............................................................3.0 µV (internal)

Signal-to-Noise Ratio ..........................................................................90 dB

Audio Output............................................32 mW into 600 ohms (Headset)

Distortion ......................................................Less than 1% at Rated Output

-6-

SET-UP

Unpacking: Unpack your TR-200 System. If there are any defects or shortages, re-

fer to the “Warranty Service Information” section in this manual.

Headset Connection: Insert the headset/microphone into the connector on the bottom of the unit. See the microphone connection diagram (Figure 4) if unit other than Telex is used.

TO HEADSET

Figure 5

Connecting Headset

Dynamic/Electret Switch: If the headset you are using has an Electret micro-

phone, the dynamic/electret switch must be in the “E” position (Electret). This switch is accessible by removing the belt clip and removing the battery holder. A +5 volt bias is available at the microphone plug for electret use.

If you are using a headset with a dynamic microphone, place the dynamic/electret switch in the “D” position (Dynamic). Refer to Figure 6.

NOTE: FOR PROPER OPERATION YOU MUST MATCH THE TYPE OF MICROPHONE YOU ARE USING WITH THE DYNAMIC/ELECTRET SWITCH LOCATED INSIDE THE UNIT.

-7-

FCC ID: B5DTR200 S/N: P/N:70681-

ELECTRET DYNAMIC

Figure 6

Dynamic/Electret Switch

Battery Installation: Assure that the OFF/ON Volume control knob is turned OFF.

Gain access to the battery compartment by removing the belt clip on the back of the unit. Release the 1/4 turn fastener located on the back of the belt clip and remove the belt clip/cover. Refer to Figure 7.

Remove the battery holder from the box. Insert six (6) AA batteries in the holder, paying close attention to polarities of the batteries.It may be necessary to turn the batteries with the thumb and forefinger the first few times the batteries are inserted into the battery holder to Assure good positive contact. Insert the holder into the case and replace the belt clip/battery cover and engage the 1/4 turn fastener.

REMOVE BELT CLIP

Figure 7

Battery Installation

-8-

Battery Check: Rotate the Volume ON/OFF Control knob clockwise to turn the unit on. Note that the battery LED (Labeled bat/ ovmod) should flash one time on good batteries. Poor batteries will cause the LED to be illuminated continuously and a bad or unusable battery will not cause any illumination at all.

bat/

talk

ovmod

Figure 8

Low Battery Indicator LED

Battery Removal: To remove the battery holder from the case to change batteries,

follow the instructions as before for removing the cover. Pull the pull bale on the holder. The holder should come out.

NOTE: For maximum uninterrupted service it is suggested that new 1.5 volt alkaline AA batteries (Mallory MN1500 or equivalent) be installed prior to each use. Avoid “shelf worn” or “economical” batteries. Operation from heavy duty nickel-cadmium batteries is also permissible, at the expense of operating time. (NEDA 10015 or equivalent). Typical life of fresh alkaline batteries with the TR-200 is approximately 24 hours maximum. 8-10 hours is typical of fully charged nickel-cadmium batteries.

NOTE: Nickel-cadmium batteries can be charged right in the holder using the Telex BC-4 Battery Charger (P/N 70741000). Refer to Battery Information Section.

-9-

Dressing the Unit: It is suggested that the unit be worn on the belt or pocket with both antenna’s hung vertically for best operating range and performance.

Figure 9

Dressing the Unit

-10-

OPERATION

Power: Rotate the ON/OFF - Volume Control Switch counterclockwise to turn the

unit on. Refer to the Battery Check Section and check batteries.

After batteries have been checked, adjust the volume control by rotating the control either clockwise or counterclockwise as required for comfortable listening volume.

ON/ INCREASES VOLUME

Figure 10

Power ON/OFF - Volume Control Knob

POWER ON/OFF & VOLUME CONTROL SWITCH

Push-to-Talk/Lock-to-Talk Switch: To enable the talk function, press and hold down on the talk button and begin talking. Releasing the talk button will discontinue talk audio. For continuous talk, quickly press the talk button twice. This enables the talk function as long as you want. To release the talk function press the talk button once more and the transmit function will cease.

NOTE: The talk LED will be illuminated whenever the talk function is activated.

talk

PUSH-to-TALK/LOCK-to-TALK SWITCH

Figure 11

Push-to-Talk/Lock-to-talk Switch

-11-

Adjusting Microphone Gain: If the transmitted audio from the microphone is too high or too low, remove the belt clip on the rear of the unit and pry out the small rubber plug to the right of the screw boss. This will reveal the microphone gain control potentiometer. Using a plastic screwdriver (supplied), adjust the gain control clockwise to increase the microphone gain or counterclockwise to decrease the microphone gain. Reinstall the rubber plug and belt clip when adjustments are complete.

CAUTION

DO NOT remove this rubber plug or attempt to adjust. This beltpack has been precisely tuned and any attempt

REMOVE BELT CLIP

to alter this adjustment will result in a non-operational unit.

REMOVE THIS RUBBER PLUG FOR ACCESS TO THE MICROPHONE GAIN CONTROL

Figure 12

Adjusting Microphone Gain

If the microphone gain is too high, the over modulation LED (the Over Modulation Circuitry uses the same LED as the Low Battery Circuitry [labeled bat/ ovmod]) will be illuminated when you are talking. Decrease the Microphone Gain until this illumination ceases when talking in a normal tone.

-12-

BATTERY INFORMATION

General

Improper battery selection, use, installation and care are the cause of numerous wireless system failures.

Alkaline Batteries: Alkaline batteries such as Mallory’s DURACELL or Eveready’s ENERGIZER provide the most reliable operation in wireless transceivers. The use of low cost carbon-zinc batteries is NOT recommended.

Nickel-Cadmium Batteries: These batteries can save you money in the long run, as they can be recharged, but they can also cause disappointing wireless performance. If you want to use rechargeable nickel-cadmium batteries you must select a heavy duty nickel-cadmium (NEDA 10015 or equivalent)

BC-4 Battery Charger

Figure 13

BC-4 Battery Charger

Remove the battery holder from the TR-200.

Snap the terminal connector onto the battery holder and plug the charger into a 110 Volt outlet.

Full charge of the battery pack is obtained after 14 to 16 hours. A full charge will last 8 to 10 hours. Extensive over-charging may damage or destroy the batteries. Please assure the charging time does not exceed 16 hours.

ENERGIZER® is a registered trademark of Union Carbide Corporation. DURACELL® is a registered trademark of Duracell Inc.

-13-

CAUTION

DO NOT ATTEMPT TO CHARGE ANY ALKALINE BATTERIES WITH THIS CHARGER. THIS CHARGER IS TO BE USED WITH NICKEL CADMIUM BATTERIES USED IN THE TR200 BATTERY HOLDER ONLY.

FCC INFORMATION

The Telex Model TR-200 transceiver is Type Accepted under United States Federal communications Commission Parts 90 and 74. Licensing of Telex equipment is the user’s responsibility and licensability depends upon the user’s classification, user’s application, and frequency selected. Telex strongly urges the user to contact the appropriate telecommunications before ordering and choosing frequencies.

CAUTION: Changes or modifications made by the user could void the user’s authority to operate the equipment.

RECOMMENDED HEADSETS

V-Series (See pages 17 and 18 for Ordering Information)

Earphone Frequency Response ..........................................10 Hz - 20 kHz

Earphone Input Sensitivity .................................................90dB@1mW

Microphone Frequency Response

Dynamic (MB-11)...............................................50 Hz - 15 kHz ±3dB

Electret (MB-12) .................................................20 Hz - 20 kHz ±3dΒ

Microphone Input Sensitivity (re: 1 volt/µbar)

Dynamic (MB-11) ........................................................................-87 dB

Electret (MB-12) ..........................................................................-84 dB

Impedance

Earphones:...............................................................Mono 150 or 600 Ω

Stereo 75 or 300 Ω

Microphones ..................................................................................150 Ω

Size H-W-D..........................8" (203 mm) x 9" (228 mm) x 4" (102 mm)

Weight

V-200 double-sided headphone..........................14 ounces (396 grams)

V-210 single-sided headset .............................10.5 ounces (298 grams)

V-220 double-sided headset .............................15.5 ounces 439 grams)

-14-

Recommended Headsets Continued

PH-1

Catalog No..................................................................................64438-005

Earphone Type ...................................................................Dynamic/Single

Earphone Impedance....................................................................150 ohms

Earphone Frequency Response .............................................50-15,000 Hz

Earphone Output ..............................................................................105 dB

Microphone Type .............................................Dynamic Noise Cancelling

Microphone Impedance ...............................................................150 ohms

Microphone Frequency Response .........................................100-8,000 Hz

Microphone Output ...................................-83 re: 1V/microbar (.071 mV)

Cable Length .................................................................6 ft. (1.8 m) coiled

Cable Connector ..........................................................Female XLR-4 type

PH-2

Catalog No..................................................................................64437-006

Earphone Type...........................................................Dynamic/Dual/Mono