Telefunken TF-LED32S52T2S User manual

LED TV/ Телевизор цветного изображения c жидкокристаллическим экраном

TF-LED32S52T2S

Instruction manual

Руководство по эксплуатации

Table of contents

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents Before you start

Utilization of the product Important safeguards Installation

Base installation Wall mounting

Connection

Outdoor antenna connection Other connections

Operation

Control elements

Front panel

Back panel Remote controller

Changing the battery

General operations

Signal sources

Teletext operations OSD operation

Channel setting Picture setting Sound setting Timer setting

Option setting Lock setting Electronic programme guide Digital programme recording Time Shift function CI information USB operation

Background information

Operations of file playback

General information

Troubleshooting

Causes of interference Accessories Specifications

2 3 3 3 4 4 4 5 5 5 6 6 6 6 7 7 8 8 8 9

9 10 10 11 11 11 12 12 12 12 13 13 14 15 15 15 16 16

Before you start

Utilization of the product

If you want to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Before you start

Important safeguards

• Please unplug the power cord from the AC outlet and contact a service center for repair if following occurs: any obvious abnormality appears in the unit, such as smoky, peculiar smell or strange sound; liquid has been spilled or other objects have fallen into the unit; no picture or sound; cover or panel is broken; although you have operated the unit following the operating instructions, it still cannot work normally.

• This unit can be connected to a power supply outlet without the third ground contact as well as with a ground contact.

• Always disconnect the power cord and antenna during a storm.

• Do not fix the power cord with a metal nail.

• Unplug the power cord from the AC outlet; also unplug the signal cables from the input ports when the unit is unused for long periods of time.

• When unplugging the plug, always hold the wide slot, do not touch the metal part, and do not destroy, twist, pull or roast the power cord.

• Please contact the service center immediately if you found that the core is showed in the air or has been broken.

• Please replace the AC outlet if the metal bolt cannot be inserted into the power socket completely or it cannot be fastened even when it was pushed in, otherwise, any accidents of shocks and fires would happen.

• Never touch the antenna lie or power plug

if it stars to thunder.

• Do not touch the power plug with wet

hands.

• Do not use any non-rated power socket with numerous devices jointed on one power socket or cable device. The wire of nondesignated capacity may cause the fire due to the generation of heat.

• All instructions must be read and understood well before you operate the unit. Heed all warnings and follow all instructions.

• Please use the accessories provided by the manufacturer. Using inadequate accessories may result in accidents.

• Please adjust the product through the panel buttons or the remote controller, do not remove the cover or attempt to service the product by yourself. Do not disassemble back cover and do not make maintenance by yourself to avoid the electric shock.

• Over-press the panel may destroy the product.

• Do not place the product on an unstable cart, stand surface, tripod, bracket, or table. The product may fall, causing serious accidents as well as the damage to the product.

• Please place the product on a flat surface in a well-ventilated location. Keep it away from the burning-light, direct sunlight, vibration, high-temperature and humidity.

• Do not place any vase, potted plant, cup, medicine and any container with water on this

Before you start

product. If the liquid is spilt, it may cause the fire, electric shock or breakdown.

• Do not install it at the place on the strong magnetic field or current field. It may cause break down. This equipment may be observed deterioration of the picture by electromagnetic radiation in electromagnetic environment.

• Fasten the wheel of the product or shelf with wheels when installing this product. If it moves or is tipped over, it may be damaged.

• Do not place any fire source such as candlelight close to this product or place it on this product. If it is tipped over or fallen down, it may cause damage or fire.

• Do not place the unit into closed space of TV for better ventilation; it can reduce the product lifetime. Keep a space at least 10 cm at above, left, and right of the TV.

• Please place all the signal cords behind of rear panel.

• Do not overexert or touch the panel when you convey the product. Do not transfer the LED TV up or down display direction.

• Do not transport it with the power cord or the connection cable connected. If you move this product with the power cord or the connection cable connected, damaged power cord, connection cable or connection terminal may cause fire, electric shock or breakdown.

• 2 persons or more shall transport the device, which is heavier than 18 kg. If you drop or tip over the device, it may damage it.

• The temperature of the product’s body becomes a little higher after a long period use. This phenomenon indicates that heat exchange in normal working mode, thus please do not let children or anyone who is sensitive of temperature to touch.

All images provided herein are schematic

drawings and may differ from real objects.

WARNING

In order to avoid damage, make sure to secure the unit on the wall according instruction.

to the wall mounting

Installation

Base installation

Cover a flat stable surface with a soft cloth. Place the TV unit facedown on the cloth. Insert the base into the lower back panel of the unit.

Align the base assembly with holes on the back of the unit cabinet and fasten with 4

screws.

Wall mounting

• For wall mounting the back panel of this unit is equipped with 4 screw holes (spread distance 200x100mm). A VESA wall-mount bracket should be used for wall mounting (the bracket is not included and should be acquired separately). Manufacturer is not responsible for improper mounting resulting in damage of the unit.

Connection

Before you start

Antenna cable connector

75 Ohm co-axis cable

Outdoor Antenna Connection

Use 75Ω coaxial cable plug or 300-75Ω impedance converter to plug in antenna input terminal on the rear of the cabinet.

Other connections

• Connect the audio sources (Including DVD, VCDR, CAMCORDER and PC) to the proper Audio input jacks ‘L’ and ‘R’.

• Connect the video source to the Composite video jack by RCA cable.

• Plug the power cable in the electric outlet, making sure the current voltage is supported.

• If the video source has a HDMI output jack, you can connect the signal to the monitor by the HDMI cable (not included).

TVRF antenna jack

• Coaxial output is intended for transmitting multi-channel sound to an external decoder (e.g. in 5.1-CH format). Coaxial cable should be used for connection.

• PCMCIA slot is used for CI modules that are obtained from your digital TV provider.

• Connect your headphones or earphones (not included) to the headphone socket of this unit. When earphones are connected, the sound output through the built-in speakers of this unit is mute.

•

LAN port allows a TV to connect to

the Internet using an Ethernet network cable.

Operation

Control elements

Front panel

SOURC E MEN U V- V+ CH- CH+ Sta ndby

1．SOURCE：

30 30

Display the input source menu. 2．MENU： Display main MENU. 3．V-/V+

Adjust sound level. In MENU mode, press“V+”or“V-”to adjust the item that you selected.

4．CH+/CH-

In TV mode，press“CH+”or“CH-”to change

the channel up and down.

1. Re mote control se nsor

2. In dicat or LED: R ED STANDB Y

3. Ke y board

In MENU mode, press “CH+”or“CH-”to select items.

5. STANDBY

Press this button to turn the unit ON from STANDBY mode. Press it

again to turn the set back to STANDBY.

REAR AV Connections

AC-I NPUT

100-240V~50 HZ

VIDE O

L R

All the terminals are(from left to right): AC Power Socket, VIDEO INPUT, AUDIO INPUT, USB PORT, COAXIAL OUTPUT.

REAR AV Connections(SIDE)

US B 3.0

LAN

HDMI2

5V 9

00mA

All the terminals are (from left to right): LAN PORT, HDMI2, USB 3.0 PORT, HDMI1, HEADPHONE, CI, RF.

COMMON INTER FACE( CI)

HDMI 1

HE ADPH ONE

USB

500mA

COAX IAL

R F

Remote controller (RC)

Operation

1:POWER:To set the TV to standby or power on. 2:

:In USB mode, used as rev er se k ey, in teletext

mode used as subpage key.

: In USB mode, used as forward key, in teletext

3::

mode used as reveal key. Press in USB Mode to continue playback.

4: :

Press in USB Playback Mod e to p au se p la yb ac k.

5: : 6:TEXT:To enter or TELETEXT. 7: SUBTITLE: To tur n on subtitles press the subtitle button

MENU: Displays the main on-screen menu.

CURSOR:

:OK

11:

: HOME button, switch to SMART TV mode. In SMART TV

mode: return to Main Menu. 12:FAV: To ac ce ss y ou r fa vourite channels list in TV or DTV mode.

13:VOL+/- 14:REC: Press to record the TV program you are watching in DTV mode. 15:NUMERIC KEYPAD: Press for direct access to channels. 16: LIST: Display a list of channels. 1

7:MUTE: To disable or enable the sound output.

in DTV mode.

To move within the menu.

: Confirms sel

: To adjust sound level.

ection.

Operation

: In USB mode, used as next key, in teletext mode used as

20: AUDIO: To select the available audio language of TV programs. 2 22:INFO: To display the program information of the show you

23:EPG: To display information about the program being viewed. 24: : Press to display and select the available video sources. 25:EXIT 26:CH+/CH-: To access the next or previous channels. 27:RECALL: DTV Mode: RECALL:Jumps to last channel viewed.

28:Colour buttons : Used for context actions and Teletext.

list key.

9: : I

n USB mode, used as previous key, in teletext mode used

as hold key.

1: : Press to stop play in USB mode.

are watching, press the info button.

: To return to the previous menu or exit menu.

Operation

on the back of the RC.

compartment making sure that the correct polarity is observed.

Operation

Changing the battery

1. Remove the battery compartment cover

2. Insert the batteries into the battery

3. Install the cover back.

1 2 3

On average, the loading time of the TV

can take up to 40 seconds. However, the loading time number of installed applications.

• Select the TV function mode. Press CH-/CH+ buttons to select previous or next channels; or press number buttons to enter a channel number directly.

• Press INFO button to display the preset TV channel play information.

Press AUDIO button in TV mode repeatedly to

• switch between various Nicam sound modes (can be unavailable for some channels). This function is optional.

might differ, depending on the

• Use two AAA batteries for the RC. The RC should be pointed at remote sensor within 8 meters and within 30 degrees at the left or the right side.

• Take the battery out of the RC if it is not used for a long time.

• Do not mix new and used batteries or different types of batteries. Weak batteries can leak and severely damage the RC.

• Do not expose the RC to shock, liquids, and do not place it in an area with high

humidity.

General operations

Power

•

Connect the plug of the power cord to the mains socket.

• Do not leave your TV in standby mode for a long period of time; if you are not going to use the unit, disconnect it from power supply.

• In TV mode the unit will automatically go to standby mode if no signal for 5 minutes.

Operations

• Press VOL- button repeatedly to decrease the volume; press VOL+ button repeatedly to increase the volume.

•

Press

again or increase volume to resume sound.

•

Press RECALL button on the RC to select from the present channel and the previously displayed channel.

to mute sound, press this button

MUTE

Signal sources

Press button, then press DOWN/UP

cursor buttons on the RC or CH+/CH-

buttons on the panel to select a source from available source list: DTV => ATV => AV => => HDMI 1 => HDMI 2 => USB.

Press OK button on the RC to confirm.

Teletext operations (option)

Select a TV channel in order to pick up the picture signal of Teletext. Teletext button functions are as follows:

TTX: Press this button to enter into TEXT mode. Press this button again to enter mixed mode. Press the button again to return to the channel you are watching.

HOLD: Press this button to stop the move to the next page. Press this button again to cancel operation.

INDEX: Press this button to go to the index page.

LIST: Toggle the list mode.

REVEAL: Press this button to reveal the concealed information. Press this button again to conceal the information.

Red/Green/Yellow/Blue buttons: Press these 4 color buttons to access directly to corresponding color page displayed at the lower parts of teletext screen.

Operation

OSD operation

1. Press MENU button to enter the setting

menu displayed on the screen.

2. Press LEFT/RIGHT cursor buttons on the RC or VOL+/VOL- buttons on the panel to go to the needed setting page.

3. Press UP/DOWN cursor buttons on the RC or CH+/CH- buttons on the panel to select a parameter to adjust.

4. Press LEFT/RIGHT buttons on the RC or VOL+/VOL- buttons on the panel to adjust the selected parameter.

5. Press MENU button to return to the root menu or exit menu setting.

Some menu items may be in grey color, in this case they are not adjustable. Pictures of OSD menu are for reference only; they may differ from the real screens.

Channel setting

CHANNEL

Antenna Type

Auto Tuning DTV Manual Tuning ATV Manual Tuning Programme Edit Signal Information CI Information

Select Press “OK” to select Press “MENU” to return

• Auto Tuning: press OK buttons to select the country and tune type for channels to start automatic search and saving of available ATV channels. After the search is finished, the unit will skip to searching DTV channels, Radio channels and Data. During the ATV search, press MENU button to skip to DTV, Radio and Data search.

• DTV Manual Tuning: Press LEFT/RIGHT

cursor buttons to select channel number. Press OK button to start searching. When the nearest available channel is found, the search will stop and the channel will be saved under the selected number. Press MENU button to quit.

• ATV Manual Tuning: Storage To: select channel number. System: select corresponding sound system. Current CH: search for next available

channel starting from current frequency.

Search: press LEFT/RIGHT buttons; the unit will search for next available channel downward or upward and save it under the current number.

Fine-Tune: perform fine adjustment of the current frequency.

• Programme Edit: this item allows you to sort TV programs according to your preferences. Enter the program edit menu:

Delete: Select the channel you want to delete.

Press red button to delete the channel.

Move (not available for DTV channels with LCN): Highlight the needed channel. Press green button; select the position to put the channel into. Press green button to confirm.

Favorite: Select the channel you want to edit. If this channel is your favorite channel, you can add it to your favorite channel list by pressing the yellow button.

Skip: Highlight the needed channel. Press blue button; now this channel will be skipped when you select previous/next channels.

• Signal Information: View the information

on the current signal.

• CI Information (only in DTV mode): This function enables you to watch some encrypted services (pay services). Please insert a CI card into the PCMCIA slot according to the arrow on the CI card.

• The function can only be gotten when

CI slot is available.

• It is possible for you to change CI (Common Interface) menu screen and service by consulting your dealer.

• Please do not insert or pull out the CI card when power on. During initialization of the CI

Operation

card, please don’t operate the TV.

• Do not insert or pull out the CI card frequently so as to avoid any damages of the TV and the CI card.

•

Software Update: Update the TV software

using a USB drive.

Picture setting

Sound setting

SOUND

Sound Mode

Balance

Auto Volume

Surround Sound

SPDIF Mode

PICTURE

Picture Mode Color Temperature Aspect Ratio Noise Reduction

MPEG Noise Reduction

Select Press “OK” to select Press “MENU” to return

• Picture Mode: Standard/Soft/User/ Dynamic. When User mode is selected, you can adjust contrast, brightness, saturation, sharpness and tint (in NTSC) of the image.

• Color Temperature: Standard/Warm/ Cool.

• Aspect ratio: Set the picture format: Auto/4:3/16:9/Cinema/Subtitle/PC Mode.

• Noise Reduction: Dynamic noise reduction effect for reducing the video noise level. Select the Off/Low/Middle/High/Default mode.

•

Screen (only in PC mode):

Auto adjust: automatical setting of the

parameters.

Horizontal Position: adjust horizontal position

of the image.

Vertical Position: adjust vertical position of

the image.

Size: adjust the image frequency manually. Phase: adjust the phase manually.

Select Press “OK” to select Press “MENU” to return

• Sound mode: Standard/Music/Movie/ Sports/User. When User mode is selected, you can adjust bass and treble.

•

Balance: adjust the balance between the

left and the right speaker.

•

Auto Volume: automatic volume adjustment.

• Surround Sound: set the surround sound effect on or off.

• SPDIF Mode: Select the digital audio output mode: PCM/RAW.

Operation

Timer setting

TIME

Clock Off Time On Time Sleep Timer

Auto Standby

Time Zone

Select Press “OK” to select Press “MENU” to return

• Clock: You can display either the DTV

signal stream time or set the system time.

• Off Time: set the time for the TV to switch

off.

• On Time: set the time, channel and volume for the TV to switch on. The TV must be in standby for the On-timer to work.

• Sleep Timer: select the period until automatic switch-off of the unit.

• Time Zone: select your time zone.

Option setting

OPTION OSD Language Audio Language

Subtitle Language Country

PVR File System

Restore Factory Default

Select Press “OK” to select Press “MENU” to return

• OSD Language: select the language of

the on-screen display (OSD) menu.

• Audio Language: select audio language

(available for some DTV channels).

•

Subtitle Language: select subtitle language

(available for some DTV channels).

•

Country: select your country.

• PVR File System (in DTV mode): Select Disc: select the storage used for PVR. Time Shift Size: select the time for Time

Shift.

Format: format the USB. Speed Check: display the speed of the

storage.

•

Restore Factory Default: restore TV settings

to their initial factory defaults.

Lock setting

LOCK

Lock System

Set Password

Block Program

Parental Guidance

Select Press “OK” to select Press “MENU” to return

• Lock system: The feature can prevent unauthorized operation of the TV set unless entering a 4-digit password. When Lock System is on and the system is locked, you must input the system password at Auto

Operation

Tuning, Manual Tuning, Programme Edit or Default. Press the right number buttons for the password. The default password is 6666.

After a password correction has been confirmed, please remember it for entering into the Parent Guide menu, all functions can not be activated until the correct password is entered.

• Set password: You can set your private password. Press the number buttons on the remote control to set the new password. When the new password has been put in twice, the setting is finished successfully. The TV will go back to previous menu.

• Block program (in TV/DTV mode): Press Green button to lock the available program you want. Press Green button again to unlock it.

Electronic Programme Guide (in DTV

mode)

Press EPG button to display the Programme Guide menu. This function gives you the detailed information of the channel, indicating the time of the program playing. From the Programme Guide it is possible to check the program information for the next eight days (If the information is available from the broadcaster). Press REVEAL button to quit.

• Record: Press Red button to set the parameters of recording, The unit is able to do schedule recording when TV is turning on or in standby mode. You can set up several schedule recording. Different schedules should not overlap. When recording starts in standby mode, the front indicators will change color and there will be no picture or sound from the unit.

You can press the POWER button to light up

the screen.

• Info: Press Green button to see the detailed information of the current channel.

• Schedule: Press Yellow button to display

the schedule list.

• Remind: If you find the desired program which will be shown in the future. Press Blue button to book program.

Digital program recording

Insert a USB, the system will automatically create a folder to store the files recorded. Recording begins when REC button is pressed, and it records all the time until STOP button is pressed or the memory is full. Press REVEAL to quit recording mode. Press INDEX to show the list of recorded files, you can select the file you want to play and view the information about it (Green button), delete it (Red button) or play it (OK).

Please note the following about PVR:

• USB storage device must have the capacity of at least 512 MB and support the USB 2.0 standard. Some non-standard storage devices may not be supported

• Try formatting the inserted storage device when you have trouble recording.

• Do not disconnect the device while the formatting is in progress. When you format the device, all data on it is deleted. It may be advisable to back up your files before formatting.

• If the USB storage device has several partitions, the PVR system can record the data on any one of them.

Time Shift function

Time shift is a feature enabling you to record an air program while you are away. Press ZOOM button to activate Time Shift while recording. Press INDEX to resume the program. Press REVEAL to quit the TIme Shift mode.

CI Information

(only in DTV mode): This function enables you to watch some encrypted services (pay services). Please insert a CI card into the PCMCIA slot according to the arrow on the CI card.

• The function can only be available

when CI card is present.

• It is possible for you to change CI

+ 28 hidden pages