Telefunken TF-LED24S40T2 User Manual [ru]

LED TV
Телевизор цветного изображения c жидкокристаллическим экраном
TF-LED24S40T2
Instruction manual
Руководство по эксплуатации
Table of contents
Table of contents
Dear customer!
Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.
Table of contents Before you start
Utilization of the product Important safeguards Installation
Base installation Wall mounting
Connection
Outdoor antenna connection Other connections
Operation
Control elements
Front panel
Back panel Remote controller
Changing the battery
General operations
Signal sources
Teletext operations
OSD operation
Picture setting Sound setting Channel setting Feature setting Setup menu
USB operation
General playback information Operations of file playback
Electronic programme guide (EPG) General information
Troubleshooting
Causes of interference Accessories Specifications
2 3 3 3 4 4 4 5 5 5 6 6 6 6 7 7 8 8 8 9
9 10 10 11 11 12 12 12 13 14 14 14 15 15
2
Before you start
Utilization of the product
If you want to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.
Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.
Before you start
Important safeguards
• Please unplug the power cord from the AC outlet and contact a service center for repair if following occurs: any obvious abnormality appears in the unit, such as smoky, peculiar smell or strange sound; liquid has been spilled or other objects have fallen into the unit; no picture or sound; cover or panel is broken; although you have operated the unit following the operating instructions, it still cannot work normally.
• This unit can be connected to a power supply outlet without the third ground contact as well as with a ground contact.
• Always disconnect the power cord and antenna during a storm.
• Do not fix the power cord with a metal nail.
• Unplug the power cord from the AC outlet; also unplug the signal cables from the input ports when the unit is unused for long periods of time.
• When unplugging the plug, always hold the wide slot, do not touch the metal part, and do not destroy, twist, pull or roast the power cord.
• When connecting cables, make sure the power is switched off.
• Please contact the service center immediately if you found that the core is showed in the air or has been broken.
• Please replace the AC outlet if the metal bolt cannot be inserted into the power socket completely or it cannot be fastened even when
it was pushed in, otherwise, any accidents of shocks and fires would happen.
• Never touch the antenna lie or power plug
if it stars to thunder.
• Do not touch the power plug with wet
hands.
• Do not use any non-rated power socket with numerous devices jointed on one power socket or cable device. The wire of non­designated capacity may cause the fire due to the generation of heat.
• All instructions must be read and understood well before you operate the unit. Heed all warnings and follow all instructions.
• Please use the accessories provided by the manufacturer. Using inadequate accessories may result in accidents.
• Please adjust the product through the panel buttons or the remote controller, do not remove the cover or attempt to service the product by yourself. Do not disassemble back cover and do not make maintenance by yourself to avoid the electric shock.
• Over-press the panel may destroy the product.
• Do not place the product on an unstable cart, stand surface, tripod, bracket, or table. The product may fall, causing serious accidents as well as the damage to the product.
• Please place the product on a flat surface in a well-ventilated location. Keep it away from the burning-light, direct sunlight, vibration, high-temperature and humidity.
• Do not place any vase, potted plant, cup,
3
Before you start
Before you start
medicine and any container with water on this product. If the liquid is spilt, it may cause the fire, electric shock or breakdown.
• Do not install it at the place on the strong magnetic field or current field. It may cause break down. This equipment may be observed deterioration of the picture by electromagnetic radiation in electromagnetic environment.
• Fasten the wheel of the product or shelf with wheels when installing this product. If it moves or is tipped over, it may be damaged.
• Do not place any fire source such as candlelight close to this product or place it on this product. If it is tipped over or fallen down, it may cause damage or fire.
• Do not place the unit into closed space of TV for better ventilation; it can reduce the product lifetime. Keep a space at least 10 cm at above, left, and right of the TV.
• Please place all the signal cords behind of rear panel.
• Do not overexert or touch the panel when you convey the product. Do not transfer the LED TV up or down display direction.
• Do not transport it with the power cord or the connection cable connected. If you move this product with the power cord or the connection cable connected, damaged power cord, connection cable or connection terminal may cause fire, electric shock or breakdown.
• 2 persons or more shall transport the device, which is heavier than 18 kg. If you drop or tip over the device, it may damage it.
• The temperature of the product’s body becomes a little higher after a long period use. This phenomenon indicates that heat exchange in normal working mode, thus please do not let children or anyone who is sensitive of temperature to touch.
All images provided herein are schematic
drawings and may differ from real objects.
Installation
Base instalation
Cover a flat stable surface with a soft cloth. Place the TV unit facedown on the cloth. First align the holes on the back panel with the supports, then fix them using the screws provided.
Wall mounting
• For wall mounting the back cabinet of this
unit is equipped with 4 screw holes. Spread distance between the holes is 100*100 mm. A VESA wall-mount bracket should be used for wall mounting (the bracket is not included and should be acquired separately). Manufacturer is not responsible for improper mounting resulting in damage of the unit.
Wall or ceiling mounting implements must be durable and sufficient enough to support the weight of the unit.
4
4
Connection
Before you start
Before you start
Outdoor Antenna Connection
Use 75Ω coaxial cable plug or 300-75Ω impedance converter to plug in antenna input terminal on the rear of the cabinet.
Other connections
• Connect the audio sources (Including DVD, VCDR, CAMCORDER and PC) to the proper Audio input jacks ‘L’ and ‘R’.
• Connect the video source to the Video input using an RCA cable.
• Plug the power cable in the electric outlet, making sure the current voltage is supported.
• When using the LED as a computer screen, connect the PC to the VGA jack from the monitor by the relevant cable (not included).
• This unit has PC audio in jack. Connect this jack to PC main unit with related audio cable in PC mode and adjust the volume to what you want.
• If the video source has a HDMI output jack, you can connect the signal to the monitor by the HDMI cable (not included).
• Coaxial output is intended for transmitting multi-channel sound to an external decoder (e.g. in 5.1-CH format). Coaxial cable should be used for connection.
• Connect your headphones or earphones (not included) to the headphone socket of this unit. When earphones are connected, the sound output through the built-in speakers of this unit is mute.
• PCMCIA slot is used for CI modules that are obtained from your digital TV provider.
5
5
Operation
Operation
Control elements
Front panel
Button
Back panel
Conne ctor
Function
COAXI AL
HDMI
VGA
PC AUDIO
RF
Mini YPbPr
USB
Description
Description
CI
6
6
Remote controller (RC)
Operation
Operation
EPG
AUDIO
Enter electronic program guide.(Onl y for DTV mo de)
Press to start recording (DTV mode); Quick Menu (USB mode)
Display and select audio systems.
7
7
Operation
on the back of the RC.
compartment making sure that the correct polarity is observed.
should be pointed at remote sensor within 8 meters and within 30 degrees at the left or the right side.
used for a long time.
different types of batteries. Weak batteries can leak and severely damage the RC.
and do not place it in an area with high humidity.
a long period of time; if you are not going to use the unit, disconnect it from power supply.
standby mode if no signal for 5 minutes.
the volume; press VOL+ button repeatedly to increase the volume.
again or increase volume to resume sound.
from the present channel and the previously displayed channel.
Operation
Changing the battery
1. Remove the battery compartment cover
2. Insert the batteries into the battery
3. Install the cover back.
1 2 3
• Use two AAA batteries for the RC. The RC
• Take the battery out of the RC if it is not
• Do not mix new and used batteries or
• Do not expose the RC to shock, liquids,
General operations
Power
• Connect the plug of the power cord to the mains socket.
• Do not leave your TV in standby mode for
• In TV mode the unit will automatically go to
Operations
• Press VOL- button repeatedly to decrease
Press
• Press RETURN button on the RC to select
8
to mute sound, press this button
MUTE
• Select the TV function mode. Press CH-/CH+ buttons to select previous or next channels; or press number buttons to enter a channel number directly.
• Press INFO button to display the preset TV channel play information.
Press AUDIO button in TV mode repeatedly to
• switch between various Nicam sound modes (can be unavailable for some channels). This function is optional.
Signal sources
Press the SOURCE button, then press DOWN/UP cursor buttons on the RC or CH+/CH- buttons on the panel to select a source from available source list: DTV => ATV => AV => PC => YPbPr => HDMI => PC => USB. Press OK button on the RC or VOL+ on the panel to confirm.
TELETEXT operations
• Select the TV source mode. Then press CH-/CH+ buttons to select TV channel in order to pick up the picture signal of Teletext.
• Press CH-/CH+ buttons to select the previous page or the next page.
• Teletext button functions are as follows:
: press this button to go to the
INDEX
index page.
Number buttons: enter the number of the
designated page directly.
REVEAL : press this button to reveal the concealed information. Press this button again to conceal the information.
 CVUUPOTQSFTTUPHPUPUIFOFYU QSFWJPVTQBHF
$PMPSCVUUPOTpress the 4 color buttons to
access directly to corresponding color page displayed at the lower parts of teletext screen
)0-% pSFTTUIJTCVUUPOUPTUPQUIF NPWFUPUIFOFYUQBHF1SFTTUIJTCVUUPOBHBJO UPDBODFMPQFSBUJPO
5&95 pSFTTUIJTCVUUPOBHBJOUPTXJUDI CFUXFFOUFMFUFYU only teletext + channel andchannel only
SIZE : press this button to enlarge the text shown on the teletext screen, and one half of page could be shown. Press this button again to view the second half of this page. Press this button third time to normal size text page view.
8
Picture Menu
Operation
SUBPAGE : switch between secondary pages by entering the four digit number.
CANCEL : when a text page is selected, it may take some time before it becomes available; press this button to return to TV mode. When the required page is found, its number will be displayed at the top of the screen; press this button to return to the teletext mode and browse the page.
OSD operation
1. Press MENU button to enter the setting
menu displayed on the screen.
2. Press LEFT/RIGHT cursor buttons on the RC or VOL+/- buttons on the panel to select setting page.
3. Press DOWN cursor button or ENTER button on the RC or CH+ button on the panel to go to the parameter list.
4. Press UP/DOWN cursor buttons on the RC or CH+/- buttons on the panel to select a parameter to adjust.
5. Press cursor buttons on the RC or VOL+/­or CH+/- buttons on the panel to adjust the selected parameter.
6. Press EXIT button to quit the menu.
Some menu items may be in grey color, in this case they are not adjustable. Pictures of OSD menu are for reference only; they may differ from the real screens.
Picture mode Brightness Contrast Sharpness Saturation Hue Color Temp Aspect Ratio
Screen Mode
Advanced Settings
Move
Adjust
EXIT: ExitMENU: Return
Picture Mode: Press UP and DOWN
buttons to select Picture Mode, then press LEFT/RIGHT button to select one of the picture modes: Standard, Mild, Personal, Dynamic).
Press PICTURE to change the picture mode directly.
Brightness/Contrast/Sharpness/
Saturation/Hue: Press UP/DOWN to select the option, LEFT/RIGHT to adjust.
Brightness: adjust the picture brightness. Contrast: adjust the highlight intensity of the
picture.
Sharpness: adjust the peak level of detail in
the picture.
Saturation: adjust color intensity. Hue: use to compensate color in NTSC
transmission.
Color Temp: change the overall color
temperature of the picture:
Standard: Default vivid color temp. Cool: gentle blue-hued image. Warm: bright red-hued image.
Aspect Ratio: select the screen aspect
ratio: Auto/4:3/16:9/14:9/Panorama/Zoom1/Zoom2.
Screen Mode: adjust the screen
parameters when using PC as a source.
Auto adjust: automatic setting of the
parameters.
Horizontal Position: adjust horizontal position
of the image.
Vertical Position: adjust vertical position of
the image.
Phase: adjust the phase manually. Clock: adjust the image frequency manually.
Advanced Settings: allows a more
detailed picture setup for advanced users.
Picture
Operation
9
9
Operation
buttons to select Sound Mode, then press LEFT/RIGHT button to select one of the sound modes: Standard, Мusic, Personal, Movie). Press SOUND to change the picture mode directly.
select the option, LEFT/RIGHT to adjust.
decrease high-pitched sounds.
decrease low-pitched sounds.
and right speakers to adapt to your listening position.
effect on/off.
choose among presets: Off, Rock, Pop, Jazz, User.
Volume automatically remains on the same level of volume if you change programmes. Because each broadcasting station has its own signal conditions, volume adjustment may be needed every time when the channel is changed. This feature allows users to enjoy stable volume levels by making automatic adjustments for each program
coaxial cable: Off/Auto/PCM.
on the current sound channel.
Operation
Sound Menu
Adjust
Sound
EXIT: ExitMENU: Return
Sound mode Treble Bass
Balance Surrond Sound EQ Setting
AVL
SPDIF Audio Description Sound Type
Move
Sound Mode: Press UP and DOWN
Treble/Bass/Balance: Press UP/DOWN to
Treble: adjust the treble effect to increase or
Bass: adjust the bass effect to increase or
Balance: adjust the balance between left
Surround Sound: toggle the surround
EQ Setting: adjust the 7 band equalizer or
AVL: toggle auto-volume control on/off.
SPDIF: control the digital sound via
Audio Description: view the information
Sound Type: Stereo/Dual I/Dual II/Mixed
10
Channel setting
Channel
Tuner Type Auto Scan Manual Scan Auto Channel Update Channel Edit Favorite Manager Common Interface Signal Information
Move
Adjust
Tuner Type: Antenna/Cable.
Auto Scan: select this option to auto scan
for available channels.
Country: select your country. Mode: select the scan mode: DTV+ATV,
DTV, ATV.
LCN: enable or disable logical channel
number.
Start: start the auto search. Digital channels
will be searched first, then analog channels. Make sure you select either Antenna or Cable as your tuner type.
Manual Scan: select this option to scan
for available channels manually.
Digital Manual Scan: manually search for digital channels. If you select Antenna as your Tuner Type simply select the channel number and press Start to initiate scanning. If your Tuner Type is Cable then following options become available:
Start: start the manual search.
Frequency: Auto/Manual enter.
Symbol Rate:
Auto/Manual enter. Modulation: Auto/16QAM/32QAM/64QAM/128QAM/25 6QAM.
S
trength: shows the strength of the signal.
Analog Manual Scan: manually search
for analog channels.
Analog Scan: select scanning frequency.
Channel to Save: select the channel number.
Color System: Auto/PAL/SECAM. Sound System: Auto/DK/BG/I/L.
AFC: automatic fine tuning on/off. Start: start the manual search.
EXIT: ExitMENU: Return
10
Operation
Auto Channel Update: enable/disable
automatic update of channel information.
Channel Edit: enter the channel editing
menu. RED, GREEN and BLUE buttons are used as shortcuts. Select the channel you want to edit with the UP/DOWN buttons and then press:
RED button to delete the channel. GREEN button to skip the channel when
browsing with CH+/- buttons.
BLUE button to make the channel movable
in the list with cursor buttons.
Common Interface: select this option
to enter the common interface submenu. Only available when a CI card inserted in the PCMCIA slot in DTV mode.
Signal Information: view the detailed
information about the current signal. Only available in DTV mode.
Lock System menu
Lock System
Enter Password Enable Channel Locks Parental Rating Lock Keypad New Password Clear Lock
Move
Adjust
Enter Password: to access this sub-menu
you must first enter the system password. Default password is 0000.
Enable: enable/disable the the lock
system. Channel locks, Parental Rating and Lock Keypad option are available when the Lock System is enabled.
Channel Locks: access the channel locks
sub-menu.
Parental Rating: access the parental
ratings sub-menu. This feature can prevent
EXIT: ExitMENU: Return
children watching adult’s TV programmes, according to the rating limit set. This function appearance according the information from broadcasting station. Therefore if the signal has incorrect information, this function does not operate.
Lock Keypad: on/off. Lock the buttons on
the TV to prevent from being pushed by young children or other unexpected usage.
New Password: enter a 4-digit system
password. If you forget it, contact a service center.
Clear Lock: select this option to clear all
locks.
Setup menu
Setup
OSD Language Audio Languages Subtitle Teletext Blue Screen Mode Setting Time Settings PVR Settings First Time Setup Reset
Move
Adjust
OSD Language: select the language of
the on-screen display menu.
Audio Languages: select primary and
secondary audio languages.
Subtitle: toggle subtitles on/off and select
their language.
Teletext: adjust teletext settings. Only
available in DTV and ATV modes.
Blue Screen: toggle Blue screen on/off.
Mode Setting: select the Home mode or
the Store mode.
Time Settings: access the time & date
setup sub-menu.
• PVR Settings: this option is intended for
adjusting the PVR (recording) settins. Requires a USB flash drive.
First Time Setup: initiate the first-time
setup.
Reset: go back to factory default settings.
EXIT: ExitMENU: Return
Operation
11
11
Operation
Operation
USB operation
General playback information
• Insert a USB drive into the USB port. Select Media source and press ENTER button. The screen will show a USB playback window, in which you can select Music, Photo, Movie and Text contents to play by pressing LEFT/ RIGHT cursor buttons and ENTER button.
• USB file systems supported: FAT32,
2.0 USB version is supported; maximum capacity 1 TB. For correct and satisfactory operation, licensed USB devices of well-known brands should be used. Avoid using USB devices of unknown brands. Playback of some file formats cannot be supported.
• This unit supports playback of video files with ASF, AVI, MKV, MPG extensions, with video codecs WMV9, DIVX, H263, MPEG-4, MPEGII, XVID and audio codec MP3.
The above list of extensions and codecs is for information only and is not a guarantee that all files having the above extensions and codecs should be read by this unit.
• Some AVI files cannot be played due to their parameters and recording conditions. Video files with AVI extension exceeding 2 GB in size may be played partially.
According to the USB 1.1/2.0 Standard, usage of a USB device with power current consumption exceeding 500 mA is not recommended without supplementary power supply. Failure to use supplementary power for connected USB drives with power consumption exceeding this value as well as defective USB drives may cause mechanical or thermal changes of elements of this unit as well as failure of internal elements of the USB port. Such damages are not warranty cases.
Warning: usage of external USB drives containing BIN files in the root directory may cause malfunction of the unit or damage to the software.
Operations of file playback
• Insert a USB into the USB port. Press the SOURCE button or select USB source and press ENTER button on the RC or VOL+ on the unit. The screen will show a USB playback window, in which you can select Music, Photo, Movie and Text contents to play by pressing LEFT/RIGHT cursor buttons and ENTER button.
• In the content menu, press cursor buttons to select folder, press ENTER button or button to enter it, then press cursor buttons to select the file you want to watch or to listen to. When highlighting the file, the file information will appear on the right (not available for text files) and picture will be previewed in the center (not available for music and text files). Press ENTER button or button to play the selected file.
• While playback, press ENTER button; the bottom of the screen will show playback menu in which you can select an operation by LEFT/ RIGHT cursor buttons or perform this operation by pressing ENTER button.
• While playback, press button to pause or resume playback. Press button to stop playback.
• When playing music files you can press / buttons to fast reverse or forward. You can press / buttons to select the desired files manually in normal condition.
• When playing photo files, you can press
/ buttons to page up or page down the file. Press LEFT/RIGHT cursor buttons to rotate the image.
• Press EXIT button to stop playback and return to the previous menu screen. corner, the list of the current available channels on the left, and the name of each programme starting in scheduled time periods on the right. Select the channel by pressing UP/DOWN and the programme by pressing LEFT/RIGHT.
12
12
Loading...
+ 28 hidden pages