Telefunken TF-LED24S2 User Manual [ru]

LED TV/ Телевизор цветного изображения c жидкокристаллическим экраном
TF-LED24S2
Instruction manual
Руководство по эксплуатации
Table of contents
Table of contents
Dear customer!
Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.
Table of contents Before you start
Utilization of the product Important safeguards Installation
Wall mounting Stand installation
Connection
Connection
Outdoor antenna connection Other connections
Operation
Control elements
Front panel
Back panel Remote controller
Changing the battery
General operations
Teletext operations OSD operation
Channel setting Picture setting Sound setting Timer setting
Option setting USB operation
General operatoins of file playback
General information
Troubleshooting
Causes of interference Accessories Specifications
2 3 3 3 4 4 4 5 5 5 5 6 6 6 6 7 7 8 8 9 9
9 10 10 10 11 11 12 12 12 13 13
2
Before you start
Utilization of the product
If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.
Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.
Before you start
Important safeguards
• Before connecting the AC power cord to the DC adapter outlet, make sure that the voltage designation of the DC adapter corresponds to the local electrical supply.
• Accessories include a DC adaptor marked with the TV model number. Do not use other adaptors with this unit.
• Please unplug the power cord from the AC outlet and contact a service center for repair if following occurs: any obvious abnormality appears in the unit, such as smoky, peculiar smell or strange sound; liquid has been spilled or other objects have fallen into the unit; no picture or sound; cover or panel is broken; although you have operated the unit following the operating instructions, it still cannot work normally.
• This unit can be connected to a power supply outlet without the third ground contact as well as with a ground contact.
• Always disconnect the power cord and antenna during a storm.
• Do not fix the power cord with a metal nail.
• Unplug the power cord from the AC outlet; also unplug the signal cables from the input ports when the unit is unused for long periods of time.
• When unplugging the plug, always hold the wide slot, do not touch the metal part, and do not destroy, refit, twist, pull or roast the power cord.
• Please contact the service center
immediately if you found that the core is showed in the air or has been broken.
• Please replace the AC outlet if the metal bolt cannot be inserted into the power socket completely or it cannot be fastened even when it was pushed in, otherwise, any accidents of shocks and fires would happen.
• Never touch the antenna lie or power plug if it stars to thunder.
• Do not touch the power plug with wet hands.
• Do not use any non-rated power socket with numerous devices jointed on one power socket or cable device. The wire of non­designated capacity may cause the fire due to the generation of heat.
• All instructions must be read and understood well before you operate the unit. Heed all warnings and follow all instructions.
• Please use the accessories provided by the manufacturer. Using inadequate accessories may result in accidents.
• Please adjust the product through the panel buttons or the remote controller, do not remove the cover or attempt to service the product by yourself. Do not disassemble back cover and do not make maintenance by yourself to avoid the electric shock.
• Over-press the panel may destroy the product.
• Do not place the product on an unstable cart, stand surface, tripod, bracket, or table. The product may fall, causing serious accidents
3
Before you start
Before you start
as well as the damage to the product.
• Please place the product on a flat surface in a well-ventilated location. Keep it away from the burning-light, direct sunlight, vibration, high-temperature and humidity.
• The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
• Do not install it at the place on the strong magnetic field or current field. It may cause break down. This equipment may be observed deterioration of the picture by electromagnetic radiation in electromagnetic environment.
• Fasten the wheel of the product or shelf with wheels when installing this product. If it moves or is tipped over, it may be damaged.
• Do not place any fire source such as candlelight close to this product or place it on this product. If it is tipped over or fallen down, it may cause damage or fire.
• Do not place the unit into closed space of TV for better ventilation; it can reduce the product lifetime. Keep a space at least 10 cm at above, left and right of the TV.
• Please place all the signal cords behind of rear panel.
• Do not overexert or touch the panel when you convey the product. Do not transfer the LCD TV up or down display direction.
• Do not transport it with the power cord connected. If you move this product with the power cord or the connection cable connected, the damaged power cord, connection cable or connection terminal may cause the fire, the electric shock or breakdown.
• 2 persons or more shall transport the device, which is heavier than 18 kg. If you drop or tip over the device, it can be damaged.
• The temperature of the product’s body becomes a little higher after a long period use. This phenomenon indicates that heat exchange in normal working mode, thus please do not let children or anyone who is sensitive of temperature to touch.
All images provided herein are schematic
drawings and may differ from of real objects.
Installation
Wall mounting
For wall mounting the back panel of this unit is equipped with 4 screw holes (4 mm diameter, 100 mm horizontal spread distance x 100 mm vertical spread distance). A wall-mount bracket should be used for wall mounting (the bracket and screws are not included and should be acquired separately). Manufacturer is not responsible for improper mounting resulting in damage of the unit.
Stand installation
Place the LED TV on a solid flat surface. Use soft material to place over the front screen to avoid any damage. Then put the slits of the stand onto the fixing elements in the lower part of the unit until a click and fix the two parts by four screws as shown below:
4
Connection
Connection
Connection
Antenna cable connector
75 Ohm co-axis cable
Outdoor Antenna Connection
Use 75Ω coaxial cable plug or 300-75Ω impedance converter to plug in antenna input terminal on the rear of the cabinet.
Other connections
• Connect a TV or CATV antenna to the
antenna jack.
• Connect a video source to the Composite
video input jack with RCA cable.
• Connect an audio source to the proper
Audio input jacks (left and right).
• Connect the power cord to the DC adaptor, then connect the adapter to the DC power jack of this unit.
• Connect PC audio input to PC main unit with related audio cable in PC mode.
• When using the unit as a computer screen, connect the PC to the PC jack of the unit by the relevant cable.
TVRF antenna jack
• If the video source has a HDMI output jack, you can connect the signal to the unit by HDMI cable (not included).
• Component input is intended for receiving component video signal if connected to the component output of external signal source. To receive audio signal for component video, please use Left and Right audio inputs of this unit.
• Connect an external device (e.g., VCR-/ DVD-recorder) to the proper Audio/Video output jacks of this unit with AV RCA cable.
• Connect your headphones or earphones (not included) to the headphone socket of this unit. When headphones are connected, the sound output through the built-in speakers of this unit is mute.
5
Operation
Operation
Control elements
Front panel
Back panel
1. POWER button
2. CH+/- buttons
3. VOL+/- buttons
4. MENU button
5. SOURCE button
6. Power indicator
7. IR sensor
8. USB port
9. Headphone jack
10. RF antenna jack
11. Component video input
12. Power input
13. Composite video input
14. Right audio input RCA
15. Left audio input RCA
16. HDMI input
17. Video output
18. Right audio output
19. Left audio output
20. PC audio input
21. PC (VGA) input
6
Operation
Remote controller (RC)
1
2
3
4
5
6
7
8
9
10
11 12 13 14 15
16
11. SOURCE/REVEAL ( ) button
12. Red/Green buttons ( / )
13. HOLD ( )/ STILL button
14. TEXT ( )/ button
17
15. P.MODE button
16. S.MODE button
Operation
17. INFO/INDEX ( ) button
18. RECALL ( ) button
19. CANCEL ( ) button
20. button
21. CH+/CH- buttons
18 19
20
22. EXIT button
23. USB button
24. Yellow/Blue buttons ( / )
25. SUBPAGE ( ) button
26. E/W button
27. PC button
21
28. HDMI button
Changing the battery
22
23 24 25 26 27
28
1. Remove the battery compartment cover on the back of the RC.
2. Insert two AAA batteries into the battery compartment making sure that the correct polarity is observed.
3. Install the cover back.
1. POWER button
2. Number buttons
3. SIZE ( )/ZOOM ( ) button
4. SLEEP button
5. LIST/REPEAT button
6. VOL+/VOL- buttons
7. button
8. MENU button
9. ENTER button/cursor buttons (LEFT/RIGHT/ UP/DOWN)
10. AUDIO ( ) button
1 2 3
The RC should be pointed at remote sensor within 8 meters and within 30 degrees at the left or the right side. Take the battery out of the RC if it is not used for a long time. Do not mix new and used batteries or different types of batteries. Weak batteries can leak and severely damage the RC. Do not expose the RC to shock, liquids, and do not place it in an area with high humidity.
7
Operation
Operation
General operations
• Connect the round terminal of the adapter to the power adapter input of the TV (the position of the input is given in paragraph Control Elements above). Connect the plug of the adapter to the power supply outlet, the power indicator will light up in red showing that the unit is in standby mode. To switch on the unit, press POWER button on the panel or on the RC. Press POWER button again to switch the unit to the standby model, the power indicator will light up in red. To switch off the unit completely, disconnect the power adaptor cord plug from the power supply outlet. If after connecting the adapter plug to power supply the power indicator does not light up in red, please wait for some time and the unit will turn on automatically (this effect takes place if the unit had been disconnected from the power supply without being previously switched to standby mode).
• Press VOL- button repeatedly to decrease the volume; press VOL+ button repeatedly to increase the volume.
• Press to mute sound, press this button again or increase volume to resume sound.
• Press SLEEP button repeatedly to set the sleep time (from 10 to 240 min or off). When sleep time is set, press this button to display the time remaining until the auto turn off.
• Press AUDIO ( ) button in TV mode repeatedly to switch between Nicam Stereo, Mono, Dual I and Dual II sound modes (can be unavailable for some channels).
• Press repeatedly TV/AV button on the unit or press SOURCE button on the RC, then press UP/DOWN cursor buttons to cycle through the available source list as follows: TV - AV - YPbPr
- VGA - HDMI - USB. Or you can press HDMI button on the RC to access the HDMI signal source directly; press USB button on the RC to access USB mode directly; press PC button on the RC to access the VGA mode directly.
• Press repeatedly S.MODE button to select sound mode: Standard => Music => Movie => Sports => User.
• Press repeatedly P.MODE button to select sound mode: User => Standard => Dynamic
=> Mild.
• Select the TV function mode. Press CH-/CH+ buttons to select previous or next channels; or press number buttons to enter a channel number from 0 to 199 directly.
• Press RECALL ( ) button on the RC to select from the present channel and the previously displayed channel.
• Press STILL button to freeze the picture on or off.
• Press button to display the Favourite channel list in TV mode (you should setup your favourite channels in Program Edit menu).
• Press INFO button to display the preset TV channel play information.
• Press ZOOM ( ) button repeatedly to select an aspect ratio: 16:9/4:3/Panorama/ Zoom1/Zoom2. The set of available aspects can vary depending on the current signal source.
Teletext operations (option)
Select a TV channel in order to pick up the picture signal of Teletext. Teletext button functions are as follows:
TEXT ( ): Press this button to enter into TEXT mode. Press this button again to enter mixed mode. Press the button again to return to the channel you are watching.
HOLD ( ): Press this button to stop the move to the next page. Press this button again to cancel operation.
INDEX ( ): Press this button to go to the index page.
SIZE ( ): Press this button to enlarge the top part of the page. Press this button again to enlarge the bottom part of the page. Press this button third time to normal size text page view.
REVEAL ( ): Press this button to reveal the cancelled information. Press this button again to cancel the information.
SUBPAGE ( ): Press this button to select sub-page. Input the number of sub-page and use numeric buttons in the format 0001 for sub page 1. The teletext will search for the sub page. Press SUBPAGE button again to exit the subpage mode.
CANCEL ( ): Press this button to exit from the teletext mode.
E/W: Press this button to switch between
8
Operation
available teletext languages.
Red/Green/Yellow/Blue buttons: Press these 4 color buttons to access directly to corresponding color page displayed at the lower parts of teletext screen.
OSD operation
1. Press MENU button to enter the setting
menu displayed on the screen.
2. Press LEFT/RIGHT cursor buttons on the RC or VOL+/- buttons on the panel to select setting page.
3. Press DOWN cursor button or ENTER button on the RC or CH+ button on the panel to go to the parameter list.
4. Press UP/DOWN cursor buttons on the RC or CH+/- buttons on the panel to select a parameter to adjust.
5. Press cursor buttons on the RC or VOL+/­or CH+/- buttons on the panel to adjust the selected parameter.
6. Press MENU button to return to the previous menu page. Press EXIT button on the RC to quit the menu.
Some menu items may be in grey color, in this case they are not adjustable. Pictures of OSD menu are for reference only; they may differ from the real screens.
Channel setting (only for TV source)
Storage to: select channel number to store
in.
Color System: select corresponding color
system.
Sound System: select corresponding sound
system.
Current Ch: select channel number.
Search: press LEFT/RIGHT buttons; the unit will search for next available channel downward or upward and save it under the current number.
Fine-tune: perform fine adjustment of the current frequency.
Programme Edit: this item allows
you to sort TV programs according to your preferences. Enter into program edit menu:
Delete: Select the channel you want to delete. Press red button to delete the channel.
Rename: Highlight the needed channel. Press green button; then press UP/DOWN buttons to select a symbol. Press LEFT/RIGHT buttons to select the next symbol. Press green button to confirm.
Swap: Highlight the needed channel. Press yellow button; select the position to put the channel into. Press yellow button to confirm.
Skip: Highlight the needed channel. Press blue button; now this channel will be skipped when you select previous/next channels.
Favorite: Select the channel you want to edit. If this channel is your favorite channel, you can add the mark to the channel as your favorite channel by pressing button.
Operation
Auto scan TV Manual tuning Programme edit
CHANNEL
Move Menu Select Exit
Auto scan: press RIGHT button to start
automatic search of available channels. To stop the process press MENU button.
TV manual tuning: Press ENTER button to
enter into manual tuning menu:
Picture setting
Picture mode Contrast Brightness Color
PICTURE
Move Menu Select
Picture Mode: User/Standard/Dynamic/
Mild.
Contrast
Sharpness Tint
Exit
9
Loading...
+ 20 hidden pages