Telefunken TF-LED22S24T2 User manual

LED TV/ Телевизор цветного изображения c жидкокристаллическим экраном

TF-LED22S24T2

Table of contents

Instruction manual

Руководство по эксплуатации

Table of contents

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents Before you start

Utilization of the product Important safeguards Installation

Base installation Wall mounting

Connection

Outdoor antenna connection Other connections

Operation

Control elements

Front panel

Back panel Remote controller

Changing the battery

General operations

Signal sources

Teletext operations OSD operation

Channel setting Picture setting Sound setting Timer setting

Option setting Lock setting Hotel mode Electronic program guide CI information USB operation

General playback information

Operations of file playback

General information

Troubleshooting

Causes of interference Accessories Specifications

2 3 3 3 4 4 4 5 5 5 6 6 6 6 7 7 8 8 8 9

9 10 10 11 11 12 13 13 13 14 14 14 15 15 15 16 16

Before you start

Utilization of the product

If you want to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Before you start

Important safeguards

• Please unplug the power cord from the AC outlet and contact a service center for repair if following occurs: any obvious abnormality appears in the unit, such as smoky, peculiar smell or strange sound; liquid has been spilled or other objects have fallen into the unit; no picture or sound; cover or panel is broken; although you have operated the unit following the operating instructions, it still cannot work normally.

• This unit can be connected to a power supply outlet without the third ground contact as well as with a ground contact.

• Always disconnect the power cord and antenna during a storm.

• Do not fix the power cord with a metal nail.

• Unplug the power cord from the AC outlet; also unplug the signal cables from the input ports when the unit is unused for long periods of time.

• When unplugging the plug, always hold the wide slot, do not touch the metal part, and do not destroy, twist, pull or roast the power cord.

• Please contact the service center immediately if you found that the core is showed in the air or has been broken.

• Please replace the AC outlet if the metal bolt cannot be inserted into the power socket completely or it cannot be fastened even when it was pushed in, otherwise, any accidents of shocks and fires would happen.

• Never touch the antenna lie or power plug

if it stars to thunder.

• Do not touch the power plug with wet

hands.

• Do not use any non-rated power socket with numerous devices jointed on one power socket or cable device. The wire of nondesignated capacity may cause the fire due to the generation of heat.

• All instructions must be read and understood well before you operate the unit. Heed all warnings and follow all instructions.

• Please use the accessories provided by the manufacturer. Using inadequate accessories may result in accidents.

• Please adjust the product through the panel buttons or the remote controller, do not remove the cover or attempt to service the product by yourself. Do not disassemble back cover and do not make maintenance by yourself to avoid the electric shock.

• Over-press the panel may destroy the product.

• Do not place the product on an unstable cart, stand surface, tripod, bracket, or table. The product may fall, causing serious accidents as well as the damage to the product.

• Please place the product on a flat surface in a well-ventilated location. Keep it away from the burning-light, direct sunlight, vibration, high-temperature and humidity.

• Do not place any vase, potted plant, cup, medicine and any container with water on this

Before you start

product. If the liquid is spilt, it may cause the fire, electric shock or breakdown.

• Do not install it at the place on the strong magnetic field or current field. It may cause break down. This equipment may be observed deterioration of the picture by electromagnetic radiation in electromagnetic environment.

• Fasten the wheel of the product or shelf with wheels when installing this product. If it moves or is tipped over, it may be damaged.

• Do not place any fire source such as candlelight close to this product or place it on this product. If it is tipped over or fallen down, it may cause damage or fire.

• Do not place the unit into closed space of TV for better ventilation; it can reduce the product lifetime. Keep a space at least 10 cm at above, left, and right of the TV.

• Please place all the signal cords behind of rear panel.

• Do not overexert or touch the panel when you convey the product. Do not transfer the LED TV up or down display direction.

• Do not transport it with the power cord or the connection cable connected. If you move this product with the power cord or the connection cable connected, damaged power cord, connection cable or connection terminal may cause fire, electric shock or breakdown.

• 2 persons or more shall transport the device, which is heavier than 18 kg. If you drop or tip over the device, it may damage it.

• The temperature of the product’s body becomes a little higher after a long period use. This phenomenon indicates that heat exchange in normal working mode, thus please do not let children or anyone who is sensitive of temperature to touch.

All images provided herein are schematic

drawings and may differ from real objects.

Installation

Base instalation

Cover a flat stable surface with a soft cloth. Place the TV unit facedown on the cloth. Align the holes in the stand with the fixing pins in the bottom of the base and fix it with 4 screws.

Wall mounting

• For wall mounting the back panel of this unit is equipped with 4 screw holes. A wall-mount bracket should be used for wall mounting (the bracket is not included and should be acquired separately). Manufacturer is not responsible for improper mounting resulting in damage of the unit.

Wall or ceiling mounting implements must be durable and sufficient enough to support the weight of the unit.

Connection

Before you start

Antenna cable connector

75 Ohm co-axis cable

Outdoor Antenna Connection

Use 75Ω coaxial cable plug or 300-75Ω impedance converter to plug in antenna input terminal on the rear of the cabinet.

Other connections

• Connect the audio sources (Including DVD, VCDR, CAMCORDER and PC) to the proper Audio input jacks ‘L’ and ‘R’.

• Connect the video source to the Composite video jack by RCA cable.

• Component input YPbPr is intended to receive component video signal from the external device. Connection is made with the help of a special component cable (not included). To receive audio signal for component video, please use Left and Right audio inputs of this unit

• Plug the power cable in the electric outlet, making sure the current voltage is supported.

• When using the LED as a computer

TVRF antenna jack

screen, connect the PC to the VGA jack from the monitor by the relevant cable (not included).

• This unit has PC audio in jack. Connect this jack to PC main unit with related audio cable in PC mode and adjust the volume to what you want.

• If the video source has a HDMI output jack, you can connect the signal to the monitor by the HDMI cable (not included).

• Coaxial output is intended for transmitting multi-channel sound to an external decoder (e.g. in 5.1-CH format). Coaxial cable should be used for connection.

• Connect your headphones or earphones (not included) to the headphone socket of this unit. When earphones are connected, the sound output through the built-in speakers of this unit is mute.

• PCMCIA slot is used for CI modules that are obtained from your digital TV provider.

Operation

Control elements

Front panel

1. Remote control sensor

2. Power indicator

TELEFUNKEN

Back panel

1. POWER button

2. SOURCE button

3. MENU button

4. VOL+/VOL- button

5. CH+/CH- button

6. AV RCA input

7. Component YPbPr input

8. PC audio input

9. PC (VGA) input

10. AV output

11. Digital audio out

12. USB port

13. Antenna input

14. HDMI input

15. CI input

16. Headphone output

Operation

Remote controller (RC)

DMP

INDEX

15. SLEEP button

16. LIST button

17. EPG button

18. button

Operation

19. Red button/ button Green button/ button Yellow button/ button Blue button/ button

20. HOLD ( )/ STILL button

21. TEXT ( )/ button

22. SUBPAGE ( ) button

23. RADIO button

24. DMP button

25. CANCEL ( ) button

26. INDEX ( ) button

27. button

Changing the battery

1. Remove the battery compartment cover on the back of the RC.

2. Insert the batteries into the battery compartment making sure that the correct polarity is observed.

3. Install the cover back.

1 2 3

1. POWER button

2. INFO button

3. button

4. Number buttons

5. SOURCE/REVEAL ( ) button

6. AUDIO ( ) button

7. SIZE ( )/ZOOM ( ) button

8. RECALL ( ) button

9. MENU button

10. EXIT button

11. ENTER button

12. Cursor buttons (UP/DOWN/LEFT/RIGHT)

13. VOL+/VOL- buttons

14. CH+/CH- buttons

• Use two AAA batteries for the RC. The RC should be pointed at remote sensor within 8 meters and within 30 degrees at the left or the right side.

• Take the battery out of the RC if it is not used for a long time.

• Do not mix new and used batteries or different types of batteries. Weak batteries can leak and severely damage the RC.

• Do not expose the RC to shock, liquids, and do not place it in an area with high

humidity.

Operation

General operations

Power

• Connect the plug of the power cord to the power supply outlet, the power indicator will flash for a while in red showing that the unit is in standby mode. To switch on the unit, press POWER button on the panel or on the RC; the indicator will light in green. Press POWER button again to switch the unit to the standby mode. To switch off the unit completely, disconnect the power cord plug from the power supply outlet.

• Do not leave your TV in standby mode for a long period of time; if you are not going to use the unit, disconnect it from power supply.

• In TV mode the unit will automatically go to standby mode if no signal for 5 minutes. In PC mode the unit will automatically go to standby mode if no signal for 30 seconds.

Operations

• Press VOL- button repeatedly to decrease the volume; press VOL+ button repeatedly to increase the volume.

• Press to mute sound, press this button again or increase volume to resume sound.

• Press SLEEP button repeatedly to set the sleep time (up to 240 minutes). When sleep time is set, press this button to display the time remaining until the auto turn off.

• Press AUDIO ( ) button in TV mode repeatedly to switch between Stereo, Mono, Dual I, Dual I+II and Dual II sound modes (can be unavailable for some channels).

• Press repeatedly SOURCE button on the unit or on the RC, then press UP/DOWN cursor buttons to cycle through the available source list as follows: ATV - DTV - Component - PC HDMI - USB - AV.

• Select the TV function mode. Press CH-/CH+ buttons to select previous or next channels; or press number buttons to enter a channel number from 1 to 235 directly.

• Press RECALL ( ) button on the RC to select from the present channel and the

previously displayed channel.

• Press LIST button to display the Channel List. Use UP/DOWN to select, CH+/CH- to scroll through the channel list.

• Press button to display the Favourite channel list in TV mode (you should setup your favourite channels in Program Edit menu).

• Press INFO button to display the preset TV channel play information.

• Press ZOOM ( ) button repeatedly to select an aspect ratio: 4:3/14:9/16:9/Zoom1/ Zoom2. The set of available aspects can vary depending on the current signal source.

Teletext operations (option)

Select a TV channel in order to pick up the picture signal of Teletext. Teletext button functions are as follows:

TEXT ( ): Press this button to enter into TEXT mode. Press this button again to enter mixed mode. Press the button again to return to the channel you are watching.

HOLD ( ): Press this button to stop the move to the next page. Press this button again to cancel operation.

INDEX ( ): Press this button to go to the index page.

SIZE ( ): Press this button to enlarge the top part of the page. Press this button again to enlarge the bottom part of the page. Press this button third time to normal size text page view.

REVEAL ( ): Press this button to reveal the cancelled information. Press this button again to cancel the information.

SUBPAGE ( ): Press this button to select sub-page. Input the number of sub-page and use numeric buttons in the format 0001 for sub page 1. The teletext will search for the sub page. Press SUBPAGE button again to exit the subpage mode.

CANCEL ( ): Press this button to cancel the teletext; press again to show the teletext.

Red/Green/Yellow/Blue buttons: Press these 4 color buttons to access directly to corresponding color page displayed at the lower parts of teletext screen.

Operation

OSD operation

1. Press MENU button to enter the setting

menu displayed on the screen.

2. Press LEFT/RIGHT cursor buttons on the RC or VOL+/- buttons on the panel to select setting page; press ENTER button on the RC or SOURCE button on the panel to confirm.

3. Press UP/DOWN cursor buttons on the RC or CH+/- buttons on the panel to select a parameter to adjust.

4. Press cursor buttons on the RC or VOL+/or CH+/- buttons on the panel to adjust the selected parameter.

5. Press MENU button to return to the previous menu page. Press EXIT button on the RC to quit the menu.

Some menu items may be in grey color, in this case they are not adjustable. Pictures of OSD menu are for reference only; they may differ from the real screens.

Channel setting

CHANNEL

Antenna Auto Tuning DTV Manual Tuning ATV Manual Tuning Programme Edit CI Information

Select Press “ENTER” to select Press “MENU” to return

• Antenna: Choose either Air or Cable as the

TV signal.

• Auto Tuning: press ENTER buttons to select the country and tune type for channels to start automatic search and saving of available ATV channels. After the search is finished, the unit will skip to searching DTV

channels, Radio channels and Data. During the ATV search, press MENU button to skip to DTV, Radio and Data search.

• DTV Manual Tuning: Press LEFT/RIGHT cursor buttons to select channel number. Press ENTER button to start searching. When the nearest available channel is found, the search will stop and the channel will be saved under the selected number. Press EXIT button to quit.

• ATV Manual Tuning:

Storage to 1: select channel number. System: select corresponding sound system. Current CH 2: search for next available

channel starting from current frequency.

Search: press LEFT/RIGHT buttons; the unit will search for next available channel downward or upward and save it under the current number.

Fine: perform fine adjustment of the current frequency.

• Programme Edit: this item allows you to sort TV programs according to your preferences. Enter the program edit menu:

Delete: Select the channel you want to delete.

Press red button to delete the channel.

Rename (in TV mode): Highlight the needed channel. Press green button; then press UP/ DOWN buttons to select a symbol. Press LEFT/RIGHT buttons to select the next symbol. Press green button to confirm.

Move (not available for DTV channels with LCN): Highlight the needed channel. Press yellow button; select the position to put the channel into. Press yellow button to confirm.

Skip: Highlight the needed channel. Press blue button; now this channel will be skipped when you select previous/next channels.

Favorite: Select the channel you want to edit. If this channel is your favorite channel, you can add the mark to the channel as your favorite channel by pressing button.

• CI Information (only in DTV mode): This function enables you to watch some encrypted services (pay services). Please insert a CI card into the PCMCIA slot according to the arrow on the CI card.

Operation

• The function can only be gotten when

CI slot is available.

• It is possible for you to change CI (Common Interface) menu screen and service by consulting your dealer.

• Please do not insert or pull out the CI card when power on. During initialization of the CI card, please don’t operate the TV.

• Do not insert or pull out the CI card frequently so as to avoid any damages of the TV and the CI card.

Picture setting

PICTURE

Picture Mode Color Temp Aspect Ratio DNR Screen

Select Press “ENTER” to select Press “MENU” to return

• Picture Mode: Home/Vivid/Standard/ Soft/User. When User mode is selected, you can adjust contrast, brightness, saturation, sharpness and tint (in NTSC) of the image.

• Colour Temperature: Normal/Warm/User/ Cool.

• Aspect ratio: Set the picture format: Auto/4:3/16:9/Zoom1/Zoom2/14:9.

• DNR: Dynamic noise reduction effect for reducing the video noise level.

• Screen (only in PC-RGB mode):

Auto adjust: automatical setting of the

parameters.

Horizontal Position: adjust horizontal position

of the image.

Vertical Position: adjust vertical position of

the image.

Size: adjust the image frequency manually. Phase: adjust the phase manually.

Sound setting

SOUND

Sound mode Balance AVL Surround Sound AD Switch

Select Press “ENTER” to select Press “MENU” to return

• Sound mode: Standard/Music/Theater/ Sport/User. When User mode is selected, you can adjust bass and treble.

• Balance: adjust balance between left and right speaker.

• AVL: set the auto volume correction on/ off. Volume automatically remains on the same level of volume if you change programmes. Because each broadcasting station has its own signal conditions, volume adjustment may be needed every time when the channel is changed. This feature allows users to enjoy stable volume levels by making automatic adjustments for each program.

• Surround Sound: set the surround sound effect on or off.

• AD Switch (in DTV mode): This is an auxiliary audio function that provides an additional audio track for visually challenged persons. This function handles the Audio Stream for the AD (Audio Description), when it is sent along with the Main audio from the broadcaster. Users can turn the Audio Description On or Off and control the volume.

Operation

Timer setting

TIMER

Clock Off Time On Time Sleep Auto Sleep Time Adjust Time Zone

Select Press “ENTER” to select Press “MENU” to return

• Clock: You can display either the DTV

signal stream time or set the system time.

• Off Time: set the time for the TV to switch

off.

• On Time: set the time for the TV to switch on. The TV must be in standby for the On-timer to work.

• Sleep: select the period until automatic switch-off of the unit.

• Auto Sleep: select the period of time after which the unit will automatically switch off if no operation is done.

• Time Adjust: if the signal time is different from the actual time, you can adjust it through this function.

• Time Zone: select your time zone.

Option setting

OPTION

Language Audio Language Subtitle Language Hearing Impaired Country PVR File System Default Health Remind

Select Press “ENTER” to select Press “MENU” to return

• Language: select the language of the

OSD menu.

• Audio Language: select audio language

(available for some DTV channels).

• Subtitle Language: select subtitle

language (available for some DTV channels).

• Hearing Impared: When Hearing Impaired is on, the screen will give some information to people whose hearing is impaired. When Off, the information will be hidden.

• Country: display the current country.

• PVR File System (in DTV mode):

Select Disc: select the storage used for PVR. Check PVR File System: check the storage

and test the speed of the system.

USB Disc: activate/deactivate USB. Format: format the USB. Time Shift Size: set the time for Time Shift. Speed: display the speed of the storage. Free Record Limit: select the recording

duration.

Digital program recording: Insert a USB, the system will automatically create a folder (_MSTPVR) to store the files recorded. Carverecording begins when button is pressed, and it records all the time until button is pressed or the memory is full. During the recording, press UP/DOWN cursor buttons to zoom in/out the record menu.

Time shift Function: Time shift is a feature

Operation

+ 24 hidden pages

Telefunken TF-LED22S24T2 User manual

Specifications and Main Features

Frequently Asked Questions

User Manual