Telefunken TF-DVR32FHD User Manual [ru]

CAR VIDEO RECORDER WITH REARVIEW

WIRED CAMERA АВТОМОБИЛЬНЫЙ ВИДЕОРЕГИСТРАТОР С ПРОВОДНОЙ КАМЕРОЙ ЗАДНЕГО ВИДА

TF-DVR32FHD

Instruction manual

Руководство по эксплуатации

Instruction manual

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for future reference.

Utilization of the product

If you want to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

• Read carefully through the manual to

familiarize yourself with this unit.

• Keep this manual handy as a reference for operating procedures and precautions. Do not allow persons who have not read through this manual to use this unit.

• Connect this unit only to the vehicle lighter jack of your car with +12-24 V DC power. If the voltage is too high, it may cause damage to this unit.

• Careful handling of the unit can prolong its operation life.

• Fully charge the battery before the first use.

• To ensure a longer battery life fully discharge and charge it several times before using.

• Due to variety of car lighter jack sizes depending of vehicle type, ensure that this unit is properly contacted in the lighter socket.

• The unit should be used only with original accessories included. The Manufacturer is not responsible for possible damage of this unit cause by using other accessories than provided by Manufacturer.

• Should this product fail to operate properly, contact your local dealer.

Controllers

Top and bottom panels

3 4

1. Mini USB port

2. Mini HDMI interface

3. Reset button (hole)

4. Microphone

Instruction manual

5. TF (microSD) card slot

6. UP button

7. M (MENU) button

8. DOWN button

9. OK/Recording button

10. MODE button

11. Lock button

12. Power ON/OFF button

Operations

Mounting

• Insert the fixing pins on the top of the

stand into the bracket holding holes in the top of the unit and move the unit backward until a click to fix it tightly to the bracket.

• Press the suction cup to a clean flat

surface in the car, then push it along the bar to the windshield. Make sure the stand is fixed properly to the surface.

• You can adjust the angle of the stand

by loosening the washer and bending the assembly knot.

• To unmount the stand, pull it towards you,

then lift the plastic ear on the suction cup.

Power and charging

To charge the battery of this unit connect its USB port to the PC with a USB cable (not included); or connect it to a car lighter socket with the supplied car adapter. The power icon

on the the display indicates the

remaining battery power.

Recording

• Before you start recording, insert a MicroSD memory card into the memory card slot of this unit until a click. Insert the card with correct side. After the card is inserted the device will turn off in order to preserve the information. Press POWER button to turn it on again.

MicroSD capacity supported: up to 32 GB, class 4 or higher. For correct and satisfactory operation, licensed MicroSD memory cards of famous brands should be used with this unit. Avoid using memory cards of unknown brands.

• Auto recording: After you connect

the unit to car power source, recording will be started automatically. After you disconnect the power source, the unit will continue recording according to the settings.

• Manual recording: Press POWER button to switch on the unit (press and hold it again if you want to switch off the unit). In recording mode the top left corner of the display shows the camera symbol indicating that the unit is ready for recording. Press OK button to start recording. Press this button again to stop recording.

• Taking photos: Press OK button in the photo mode to take photos.

• While recording, the recording time is

Instruction manual

shown in red figures in the top right corner of the display. The unit will save video files automatically after each 1, 3 or 5 minutes (see “Setup“ paragraph below for more details). When the memory card is full, old files will be deleted and the new files will be recorded instead. Press OK button to stop and to continue recording.

• Before removing memory card stop

recording. Press on the card until a click to remove it.

• Motion detector recording is available after

you switch on this item in the setting menu (see “Setup“ paragraph below for more details). The unit will go to recording mode if there is image motion in front of the lens. When a motion is detected, the unit will start to record a video fragment (no matter whether there is motion or not during the recording period), after the fragment is recorded, the unit comes to standby mode till a motion is detected again.

• G-sensor. If overload resulting from an

impact exceeds the setup value (1 g = 9.8m/s2; see “Setup“ paragraph below for more details), the current video fragment will be automatically protected from re-recording.

• SOS function. When you press Lock button

during video recording, the current fragment will be protected from rerecording.

• During recording press DOWN to mute the

sound.

• Press the MODE button repeatedly to

switch between video recording, photo and playback modes.

Playback mode

• Stop the recording and press MODE

to enter playback mode. Press UP/DOWN button to choose the file. Press and hold the UP button to select the rearview camera file. Press OK button to play the selected file. Press OK button to stop or resume playback.

• In file playback mode select a file, then

hold the MENU button. A menu will appear in

which you can select to delete or protect the file. Select either option, then press OK button to confirm.

HDMI

• The HDMI output is used to connect the

included wired rearview camera.

PC connection

• Connect the unit to a computer using a

USB connection cable (not included). Now the unit can be used as a mass storage device ("Mass Storage") or as a webcam for your PC ("PC Camera").

• The automatic driver management

software will launch on the PC. Follow the onscreen instructions to properly install the camera driver.

Setup

In recording mode press the MODE button to choose the needed operation mode (Video/ Photo/Playback). Press M to enter the setup menu for the current mode. In the menu press UP/DOWN buttons to select settings. Press OK button to go to adjustment of the selected setting; select options with cursor button and press OK button to confirm.

Some menu items may be in grey color, in this case they are not adjustable. The menu in your unit may be changed without prior notice and hence be different from the menu described below.

General system setup

• LCD off: activate and set the idle time

period of the screen saver or turn it off.

• Auto Power Off: Off / 3 minutes / 5

minutes / 10 minutes: select the time period after which the unit will automatically switch off, or disable this function.

• Frequency: 50 Hz/60 Hz.

Instruction manual

• Beep Sound: enable or disable beeping

sounds when pressing buttons on the unit.

• Language: select the system language.

• Date/Time: set the current year, month

and day by pressing UP/DOWN buttons and pressing OK button to confirm.

• Format: select this option to format the

inserted SD card. WARNING: all data on the card will be deleted.

• Default Settings: select OK to reset all

settings to default values.

• Version: check the current firmware

version info.

Video setup

• Resolution: select video resolution: 1080P

1920*1080 and 720P 1280*720.

• Loop Record: Off/1 min/3 min/5 min. Select

the maximum record cycle time.

• Exposure: adjust the image exposure.

• Motion Detection: Off/On. Activate or

deactivate the motion detection function.

• Recording: Off/On. Activate or deactivate

recording of sound for video recording.

• Date Stamp: Off/On. Enable or disable the

display of the current date on the recorded video.

• Gravity Sensor: Off/Low/Medium/High.

Adjust the gravity sensor sensitivity or turn this feature off.

• Parking Monitor: automatic power on and

recording when the unit detects vibrations in a stalled car.

Photo setup

• Resolution: 12M (4032*3040) / 10M (3648*2800) / 8M (3456*2480) / 5M (2592*2016) / 3M (2048*1600) / 2M (1920*1088) / 1M (1280*720) / VGA (640*480) Select the size and resolution of the image.

• Quality: Fine/Normal/Economy. Select the

image quality.

• Sharpness: Soft/Normal/Strong. Select the

image sharpness mode.

• White Balance: select the white balance mode: Auto/Daylight/Cloudy/Tungsten/ Fluorescent.

• ISO: Auto/100/200/400. Adjust ISO sensitivity.

• Exposure: adjust the image exposure.

• Date Stamp: Off/On. Activate or deactivate date display on the photo.

Playback mode setup

• Delete: Delete Current/Delete All. Select “OK“ to delete or “Cancel“ to cancel.

• Protection: Lock One/Unlock One/Lock All/ Unlock All. Enable or disable the protection of files from manual deleting or overwriting.

+ 14 hidden pages