Telefunken TF-DVR22HD User manual

CAR VIDEO RECORDER / АВТОМОБИЛЬНЫЙ ВИДЕОРЕГИСТРАТОР

TF-DVR22HD

Instruction manual

Руководство по эксплуатации

Instruction manual

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Utilization of the product

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

• Read carefully through the manual to

familiarize yourself with this unit.

• Keep this manual handy as a reference for operating procedures and precautions. Do not allow persons who have not read through this manual to use this unit.

• Connect this unit only to the vehicle lighter jack of your car with +12-24 V DC power. If the voltage is too high, it may cause damage to this unit.

• Careful handling of the unit can prolong its operation life.

• Fully charge the battery before the first use.

• To ensure a longer battery life fully discharge and charge it several times befor using.

• Due to variety of car lighter jack sizes depending of vehicle type, ensure that this unit is properly contacted in the lighter socket.

• The unit should be used only with original accessories included. The Manufacturer is not responsible for possible damage of this unit cause by using other accessories than provided by Manufacturer.

• Should this product fail to operate properly, contact your local dealer.

Controllers

Top panel

2 3

1. Full HD camera lens

2. AV out

3. Reset button (hole)

Instruction manual

Rear panel

4. Indicator light

5. Display

6. MODE button

7. DOWN button

8. UP button

9. OK button

TF-DVR22HD

6 7 8 9

Side panels

10. POWER button

11. MicroSD/TF card slot

12. MENU button

13. USB port

14. Microphone

15. HDMI output

Operations

Mounting

• Insert the fixing pins on the bottom of the stand into the bracket holding holes in the top of the unit and move the unit forward until a click to fix it tightly to the bracket.

• Press the suction cup to a surface in the car, then turn the ring to the LOCK position. Make sure the stand is fixed properly to the surface.

• You can adjust the angle of the stand by loosening the washer and bending the assembly knot.

• To unmount the stand, turn the ring to the UNLOCK position, then lift the plastic ear on the

suction cup.

Power and charging

To charge the battery of this unit connect its USB port to the PC with the supplied USB cable; or connect it to a car lighter socket with the supplied car adapter. The power icon

on the bottom right corner of the display

indicates the remaining battery power.

You can also connect the power cable to the holder to in order to achieve an optimal and convenient location of the cable in the car.

Recording

• Before you start recording, insert a MicroSD

memory card into the memory card slot of this

MIC

HDMI

unit until a click. Insert the card with correct side. After the card is inserted the device will turn off in order to preserve the information. Press POWER button to turn it on again.

MicroSD capacity supported: up to 32 GB, class 4 or higher. For correct and satisfactory operation, licensed MicroSD memory cards of famous brands should be used with this unit. Avoid using memory cards of unknown brands.

• Auto recording: After you connect the stand of the unit to car power source, recording will be started automatically. After you disconnect the power source, the unit will

Instruction manual

continue recording till the battery is depleted.

• Manual recording: Press POWER button to switch on the unit (press and hold it again if you want to switch off the unit). In recording mode the top left corner of the display shows the camera symbol indicating that the unit is ready for recording. Press OK button to start recording. Press this button again to stop recording.

• While recording, the recording time is shown in white figures in the top right corner of the display. The unit will save video files automatically after each 3, 5 or 10 minutes (see “Setup“ paragraph below for more details). When the memory card is filled, old files will be deleted and the new files will be recorded instead. Press OK button to stop and to continue recording.

• When the environmental lighting is not bright enough, the unit will automatically activate the IR lights in the front panel of the unit (if this function is set to Auto mode; see “Setup“ paragraph for more details).

• Before removing memory card stop recording. Press on the card until a click to remove it.

• Motion detector recording is available after you switch on this item in the setting menu (see “Setup“ paragraph below for more details). The unit will go to recording mode if there is image motion in front of the lens. When a motion is detected, the unit will start to record a video fragment (no matter whether there is motion or not during the recording period), after the fragment is recorded, the unit comes to standby mode till a motion is detected again.

• G-sensor. If overload resulting from an impact exceeds the setup value (1 g = 9.8m/s2; see “Setup“ paragraph below for more details), the current video fragment will be automatically protected from re-recording.

• SOS function. When you press MODE button during video recording, the current fragment will be protected from rerecording.

• Zoom: Press and hold UP/DOWN buttons during the record to zoom in/out.

Playback mode

• Press MODE button repeatedly to enter playback mode. Press UP/DOWN button to choose the source and files. Press OK button to play the selected file. Press OK button to stop and resume playback.

• In file playback mode select a file, then press and hold the MODE button. A menu will appear in which you can select to delete, protect or slide show the file. Select either option, then press OK button to confirm.

AV output and HDMI output

• Connect this unit (AV out) to an external audio-video device (e.g. car TV) with a 2mm audio-video cable (included). Now this unit can be used as audio and video signal source for the external device.

• Connect the HDMI output of this unit to an external audio-video device (e.g. car TV) with the HDMI cable (not included). Now this unit can be used as high-quality digital signal source for the external device.

Setup

In recording mode press MODE button to choose the needed operation mode (Video/ Photo/Playback). Press MENU button to go to settings of the selected mode; select options with cursor button and press OK button to confirm. Press MENU button twice to go back to initial menu. Press MENU button once to exit the menu.

Some menu items may be in grey color, in this case they are not adjustable. The menu in your unit may be changed without prior notice and hence be different from the menu described below.

General system setup

• Date/Time: set the current year, month and day by pressing UP/DOWN buttons and pressing OK button to confirm.

• License NO: set your car license plate number by pressing UP/DOWN buttons and pressing OK button to confirm or press OK button repeatedly to turn this feature off.

Instruction manual

• Auto Power Off: Off/3m/5m/10m: select the time period after which the unit will automatically switch off or disable this function.

• Beep Sound: enable or disable beeping sounds when pressing buttons on the unit.

• Delay Off: Off/30s/1m/3m: select the time period after switching the car ignition off when the unit will continue recording or disable this function.

• Language: select the system language.

• TV Mode: NTSC/PAL.

• Frequency: 50 Hz/60 Hz.

• Screen Protection: Off/3m/5m/10m: Select the time period after which the unit will automatically switch off the screen backlight.

• IR LED: Off/On: turn the infrared lights on or off during recording in dark envinronments.

• Format: select this option to format the inserted SD card. WARNING: all data on the card will be deleted.

• Default Setting: select OK to reset all settings to default values.

• Version: check the current firmware version info.

Video setup

• Resolution: select video resolution: 1080FHD1920x1080/720P1280x720/ WVGA848x480/VGA 640x480.

• Loop Recording: Off/1 minute/3 minute/5 minute/10 minutes. Select the maximum record cycle time.

• WDR: Off/On. Activate or deactivate the Wide Dynamic Range (WDR) feature.

• Exposure: adjust the image exposure.

• Motion Detection: Off/On. Activate or deactivate the motion detection function.

• Record Audio: Off/On. Activate or deactivate recording of sound for video recording.

• GSENSOR: Off/High/Medium/Low. Adjust the G-sensor sensitivity or turn this feature off.

• Date Stamp: Off/On. Enable or disable the display of the current date on the recorded video.

• Monitor Parking: Off/On. This feature

enables the camera to start recording in off mode after collision, e.g. when your car is parked and someone hits it.

• Parking Sensitivity: High/Medium/Low. Adjust the sensitivity of the Monitor Parking feature.

Photo setup

• Capture Mode: Single/2S Timer/5S Timer/10S Timer. Select the delay period after which the photo will be taken automatically.

• Resolution: 16M/12М/10M/8М/5М/3М/2МHD/VGA/1.3М. Select the size and resolution of the image.

• Sequence: Off/On. Activate or deactivate sequential image capture.

• Quality: Fine/Normal/Economy. Select the image quality.

• Sharpness: Soft/Normal/Strong. Select the image sharpness mode.

• White Balance: select the white balance mode: Auto/Daylight/Cloudy/Tungsten/ Fluorescent.

• Color: Color/Black & White/Sepia. Select the color mode

• ISO: Auto/100/200/400. Adjust ISO sensitivity.

• Exposure: adjust the image exposure.

• Anti-Shaking: Off/On. Enable or disable the anti-shaking feature.

• HDR: Off/On. Enable or disable the High Dynamic Range feature..

• Date Stamp: Off/Date/Date Time. Activate or deactivate showing of date on the photo.

Playback mode setup

• Delete: Delete Current/Delete All. Select “OK“ to delete or “Cancel“ to cancel.

• Protect: Lock Current/Unlock Current/Lock All/Unlock All. Enable or disable the protection of files from manual deleting or overwriting.

• Slide Show: 2 seconds/5 seconds/8 seconds. Select the period of showing the photo on the display during slide show.

+ 9 hidden pages