Telefunken S4400DM, S5400DMF User Manual
Bedienungs-
anleitung•
Manualedi
utilizzazione•
Manuel
d’utilisation•
User
manual•
• PALcolor S4400 DM/5400 DM/5400 DM F •
Gebruiks-
aanwijzing•
TV
P.
C
A
VCR
P.
B
CD
<< > >>
ZOOM
0
SP/LP
A - Z
PR
1
4
56
AV
0
-/--
E
Z - A
987
_
_
_
TV
32
A
B
D
E
TV
>>
0
ZOOM
AV
RC 1360
LR 06 - AA LR 06 - A
2 x LR 06 1,5 V.
A - Z
1
4
SP/LP
PR
56
AV
0
-/--
AV
Z - A
32
987
GB
television set
safety precautions
3
SAFE USE OF THE EQUIPMENT
10 cm
5 cm
10 cm
10 cm
10 cm
1. TO TURN ON
LEAVE ROOM FOR VENTILATION
AVOID HEAT, WATER, DIRECT
SUNLIGHT.
Do not place audio loudspeakers
near to television. The magnets
in the speakers could cause
patches of colour to appear
on the screen.
To ensure your personal safety and the efficient operation of your
equipment, please follow the advice given below :
Télévision sets need ventilation to avoid overheating which can cause
damage to the components. The ventilation slots at the back of the set
should not be covered up by curtains, small covers, newspapers, etc…
There must be enough room in built-in cabinets to allow for the cooling
air to circulate. The set should not be placed directly next to heating.
This appliance is designed for use in dry areas. If occasionally you
should whish to operate it outdoors (for example, on the balcony or
veranda), you must insure that it is protected against all forms of
moisture (dew, rain, splashed water).
A cold set may be switched on in a warm room only after any
condensation which may happen to be on the screen has evaporated.
Never remove the cabinet back. Have your aerial installed by an
authorised dealer or service technician.
In the evenings, after the TV programmes, or in case of a prolonged
absence, it is recommended that the appliance be switched off using
the main power switch. Even if the ON/OFF switch is in OFF position
the television set is not completely separated from the mains. In order
to separate it completely from the mains, it has to be disconnected by
unplugging the mains plug. Remove the power plug from the wall
outlet under the following conditions :
1. During a thunderstorm. It is also recommended that you disconnect
the aerial plug.
2. If you find a burning smell or smoke emerging from the set.
Additional information :
Your TV set is adequately shielded to prevent emission of X-rays.
The acceleration voltage does not exceed the maximum value of 33 kV.
Work by non-qualified technicians, modification of the high voltage
setting or the replacement of the tube with a model that does not
comply with the manufacturer’s specifications may lead to a
considerable increase in X-ray radiation.
A set changed in any of the above ways no longer satisfies the initial
specifications and should not be put back into service.
2. CARE OF THE EQUIPMENT
3. DEMAGNETISATION
The screen should be cleaned with liquid glass cleaner.
• Never use abrasive cleaners.
• To clean the front and the cabinet of your equipment use a soft cloth dipped in mild detergent. The use of
strong solvents such as white spirits or alcohol based products could damage your equipment.
• Clean the vents on the rear panel of your set regularly.
The earth’s magnetic field may have an effect on your television by causing patches of colour to appear on the
screen. If this happens :
• Switch off the television with the on-off button ;
• Wait a few minutes and then press again to switch on.
This allows the screen to be demagnetised automatically. If patches of colour are still visible repeat the procedure.
The pages of this publication are printed on recycled paper.
PROGRAMME
Set-up - Preferences Browse - Clock - Lock Tuning - Sound adjustments - AV1 - AV2 - AV3.
SOUND
Loudspeakers - Headphone - AV (Audiovisual).
PICTURE
Picture - PIP - Format.
TELETEXT / TOPTEXT / FASTEXT
PERSONAL ADJUSTMENTS
and scrolling back through the menus.
TO REMOVE THE MENU DISPLAY
or to display programme information, the type of sound
transmission (MONO, STEREO or DUAL),
the programme name and number, the time.
PICTURE FREEZE
ZOOM FUNCTION
TO CALL UP PREVIOUSLY VIEWED PROGRAMME
TO CALL UP ALL PROGRAMMES IN TURN
VOLUME
- Horizontal movement in the menus
- -/+ adjustments of other functions.
Keys 1 to 0 are used to :
- Select the programmes (from 1 to 99)
- Enter the channels numbers
- The 0 key is used to call AV inputs 1, 2 and 3.
MUTE
STAND-BY
REMOTE CONTROL ILLUMINATION
To operate your television set by remote control,
the selector switch TV-VCR must be on TV
position
When a red, green or yellow button is pressed for the first
time, the contents of the menu are displayed at the top of
the screen and the menu of the function selected is
displayed at the bottom of the screen.
Moving horizontally along in the menus
selects the required function on the contents
line if it has not been already selected.
- The selected function is displayed in the same colour as
the button pressed (red, green, yellow).
- The line selected in the menus is displayed in characters
twice as high and in the same colour.
Press the coloured button repeatedly to move down
through the menus selecting different lines.
Make any adjustments.
Changes are saved when you quit the menus, except in
the PROGRAMME menu.
CONNECTIONS AND COMMANDS 5
AUTO-PROGRAMMING 6/8
Switching on - Automatic station search
Programme organiser - New region
INSTALLATION 8/9
Volume limitation - Menu language Programme number display - Time reference Preferred settings
PICTURE ADJUSTMENTS 10/13
PIP - Format
SOUND ADJUSTMENTS 14/15
Loudspeakers - Headphone - AV
DAY TO DAY OPERATION 16/17
Switching on/Selecting programmes - Browse
OTHER FUNCTIONS - EXTRAS 18/21
Clock - Child lock - Lock
CONNECTIONS 22/24
Units connected - Calling up audiovisual programmes -
TELETEXT 25/27
Calling up Teletext - Options - Alarm - How to select Subtitles - New flash
MANUAL PROGRAMMING 28/29
Norm - Decoder - Channel/Cable - Programme - Fine
Tuning - Station name - Store/Erase - Access to the
organiser.
BATTERIES :
Refer to page 24 for the fitting of the batteries
contents
remote control
functions
remote control
using
C
P.
A
B
AV
PR
SP/LP
ZOOM
0
-/--
1
4
56
987
0
32
A - Z
Z - A
AV
E
D
TV
>>
television set
connections and commands
5
VIDEO L AUDIO R
INSTAL
STATUS
PR +
PR -
+
-
On/Standby light:
Green : on
Red : Stand-By
On / Off switch
Volume adjustments
Display
Programme
Selection
Installation-
menu
Video and audio sockets
S-Video and
audio sockets
Headphone socket
Ø 6,35 mm
AV3
AV3
Connect to AC main supply
220-240 V~50 Hz
HiFi Amplifier
AV 2
AV 1
Ψ 75
(OUT L)
(OUT R)
Camcorder
S-Video Video Audio
(IN)
(OUT)
Aerial
*
Main loudspeakers
Video recorder
Video recorder
Decoder
Video games consoleCDV player
Satellite receiver
Camcorder
Camcorder
Surround loudspeakers
S-VHS
Hi-8 mm
or VHS
8 mm
AV1
AV2
AV2
ON THE FRONT AND AT THE RIGHT SIDE OF THE SET
AT THE BACK OF THE SET
For further details,
see page 22.
GB
*We recommend that you use an aerial cable with double isolation.
NETHERLANDS : [ 1 ]
BELGIUM : [ 2 ]
LUXEMBURG : [ 3 ]
SWEDEN : [ 4 ]
DANMARK : [ 5 ]
FINLAND : [ 6 ]
NORWAY : [ 7 ]
OTHERS : [ 8 ]
Previous page : [ 9 ]
CHOOSE YOUR COUNTRY :
UK : [ 1 ]
FRANCE : [ 2 ]
GERMANY : [ 3 ]
ITALY : [ 4 ]
SPAIN : [ 5 ]
PORTUGAL : [ 6 ]
SWISS : [ 7 ]
AUSTRIA : [ 8 ]
Next page : [ 9 ]
Turn on the television set main power.
The WELCOME menu is displayed.
If it is not,
Press the INSTAL button on the television set control panel.
Briefly press the remote control button number corresponding to
the number of the language you require for the menus.
A list of countries appears (on two pages).
To go to the next or previous pages, press
Briefly press the remote control button corresponding to the
country in which you are located.
For example : England, press
The menu which then appears permits the user to :
• start an automatic search,
• search for new channels,
• access channel organisation.
You can always leave the menus at any time by pressing
the button.
For the first time or after a change of region :
start automatic channel search by pressing the button
Searching for stations and storing them in the memory depends
on the language chosen from the WELCOME menu.
The previously memorised stations are erased.
AUTO-PROGRAMMING is completed when the cursor is at
the extreme right.
To interrupt the search, press briefly on the key,
this displays the channel management menu.
WELCOME
television set
auto-programming
6
This set is equiped with an automatic station search system which is used for :
• Searching for all the stations received in your region and storing them in memory
• Automatically searching for the name of the station
• Automatically allocating a programme number.
WELCOME
BIENVENUE
WILLKOMMEN
BIENVENIDO
BENVENUTO
VÄLKOMMEN
WELKOM
ENGLISH
FRANÇAIS
DEUTSCH
ESPAÑOL
ITALIANO
SVENSKA
NEDERLANDS
Press
Appuyer
Drücken
Pulse
Premere
Tryck
Druk op
key number
sur la touche
Sie die Taste
tecla numero
il tasto
knapp nummer
knop nummer
[1]
[2]
[3]
[4]
[5]
[6]
[7]
AUTO - PROGRAMMING
Searching for stations
10 stations found
To help you, follow the instructions at the
bottom of the menu (grey background).
AUTO-PROGRAMMING
INSTAL
L
1
A-Z
1
A-Z
1
A-Z
2
3
Z-A
9
TV
>>
1
A-Z
TV
>>
AERIAL INSTALLATION
Make sure that the aerial cable and decoder (if any)
are connected to this TV set.
[ 1 ] Launch terrestrial installation
[ 2 ] Update terrestrial installation
[ 3 ] Access to the organiser
09
PR+, PR- Select a station
+, -, 0..9 Move this programme
Blue Change the name
Yellow Erase this station
To exit, press the (TV) key
+, - Next/Previous position
PR+, PR- Select a character
Green Confirm new name
Red Cancel new name
C
C N N
S-
09
+, - Next/Previous position
PR+, PR- Select a character
Green Confirm new name
Red Cancel new name
- - - - - - -
CHILD
C N N
PR+, PR- Select a station
+, -, 0..9 Move this programme
Blue Change the name
Yellow Erase this station
To exit, press the (TV) key
07
08
09
01
02
03
04
05
06
07
08
09
Moving PR 06 CANAL+ to PR 04
+, -, 0..9 Give it another number
Green Confirm change
Red Cancel change
television set
auto-programming
7
TV
>>
PR
When the automatic search is completed, the
Programme Organiser menu appears.
Scan through to check that the stations found are correctly
numbered and named as you want than:
• IF YES ➡ press briefly
the menu disappears and is replaced by the picture of the
programme selected.
• IF NO ➡ you make changes as follows
Select the programme number to be changed.
Bring the cursor to the new programme number.
You may also use the number buttons 0 to 9.
Confirm the change (green button).
Press the blue button briefly.
A list of station names per country appears
United Kingdom Nederlands
France Belgique
Deutschland Luxembourg
Italia Sverige
España Danmark
Portugal Finland
Schweiz Norge
Österreich
Select the country you require.
If the name appears in the list displayed,
select the name
Confirm the selection (green button).
If the name does not appear in the list displayed,
select the "- - - - - -"line
You have 6 characters to enter a station name
To enter a station name,
Press the green button briefly and
the first character flashes.
Select the first character of the new name.
Enter the next character
and repeat the process up to the last character.
Confirm your choice (green button). The new name is
stored in the memory and the list disappears.
Programme Organiser
PR
D
B
PR
B
- The programme number
- The station name
Programme Organiser
PR+, PR- Select the station
+, -, 0..9 Move this programme
Blue Change the name
Yellow Erase this station
To exit, press the (TV) key
01
02
03
04
05
06
07
08
09
Programme Organiser
01
02
03
04
05
06
07
08
09
+, - Next/Previous name page
PR+, PR- Select a new name
Green Confirm new name
Red Cancel new name
United Kingdom
SKYONE
DISCOV
UKGOLD
SKYSPO
BRAVO
ESPORT
S-NEWS
M T V
EUNEWS
- - - - - - -
BBC 1
BBC 2
I T V
CHAN 4
CHAN 5
SKY +
M-GOLD
M-CHAN
CHILD
C N N
B
B
PR
PR
This menu is used to :
• change the programme number,
• change the station number,
• delete a programme.
GB
television set
auto-programming
8
B
P.
C
Select the programme to be deleted.
Press the yellow button.
Confirm your choice (green button).
The programme is deleted
the following programme is selected.
You may cancel any unconfirmed command (change of
programme number or channel name, programme erasure)
by pressing the red button .
To search only for new channels :
Press the INSTAL. button on the televisions set key pad.
Select the country and press the button
When search is finished, the Programme Organiser menu appears.
Reorganise the programmes.
To do this, follow the instructions given on the previous page.
To make menu disappear, press on
01 BBC 1
02 BBC 2
03
04
05
06
07
08
09 CANAL+
Erase PR 04 CANAL+
Green Confirm erase
Red Cancel erase
PR
To delete a programme
INSTAL
L
TV
>>
2
New channels
Turn on the television set by pressing
one of the buttons from 1 to 9.
A
Press the yellow button then the (-) button.
The SET-UP menu is displayed
Select the Max. Volume line (yellow button).
Set the maximum volume with the cursor.
The volume cannot be set to zero when using this function.
installation
SET-UP
Maximum Volume Limitation
Par ce menu, vous pouvez :
• Limiter le volume sonore maximum.
• Modifier la langue des menus (allemand, espagnol, français, anglais, italien, suédois).
• Obtenir l'affichage du numéro de programme regardé.
• Mémoriser le numéro de programme de référence horaire.
With this menu you may:
• Limit the maximum volume.
• Change the menu language (German, Spanish, French, English, Italian, Swedish, Dutch),
• Permanently display the number of the programme being watched,
• Store the time reference programme number,
PREFERENCES SET-UP
TELEFUNKEN
Max. Volume
Language GB F D E I S NL
Programme Display Off On
Time reference PR 01
IR download (-)No Yes(+) PR--
Teletext Fine Tuning Off On
PREFERENCES SET-UP
TELEFUNKEN
Max. Volume
Language GB F D E I S NL
Programme Display Off On
Time reference PR 01
IR download (-)No Yes(+) PR--
Teletext Fine Tuning Off On
P.
C
P.
C
television set
installation
9
Select the Language line (yellow key).
Select
All the menus will be displayed in the language selected.
Select the Programme Display line (yellow key).
Select : • Off no permanent display.
• On the programme number
is permanently displayed
Select the Time reference (yellow key).
The television set internal clock must be set.
This synchronises automatically when the television set is
turned on to a programme broadcasting Teletext, you can
opt to select any one of the 4 channels - BBC1, BBC2, ITV, CH4.
Select the corresponding programme number.
The IR download line has no effect on your TV set.
This adjustment allows writing errors (missing letters) on the teletext pages of French networks (L Standard) to be reduced.
To do this,
On must be selected in the Teletext Fine Tuning line.
This adjustment is not active for B, G, D, K, K' and
I standards.
This menu enables you to save your preferred settings.
Press the yellow or pink key repeatedly to return to the
Menu contents line.
Press to display the PREFERENCES menu.
Select the line required with the yellow key.
Set with the key.
Erase the menu.
To return to your preferred settings at any time,
press the pink key.
Menu language
Programme number display
Time reference
Teletext Fine Tuning
PREFERENCES SET-UP
TELEFUNKEN
Max. Volume
Language GB F D E I S NL
Programme Display Off On
Time reference PR 01
IR download (-)No Yes(+) PR--
Teletext Fine Tuning Off On
PREFERENCES SET-UP
TELEFUNKEN
Max. Volume
Language GB F D E I S NL
Programme Display Off On
Time reference PR 01
IR download (-)No Yes(+) PR--
Teletext Fine Tuning Off On
PREFERENCES SET-UP
Volume
Brightness
Colour
Contrast
resets to these preferences
TELEFUNKEN
PREFERENCES
GB : English
F : French
D : German
E : Spanish
I : Italian
S : Swedish
NL : Dutch
PREFERENCES SET-UP
TELEFUNKEN
Max. Volume
Language GB F D E I S NL
Programme Display Off On
Time reference
PR 01
IR download (-)No Yes(+) PR--
Teletext Fine Tuning Off On
P.
C
P.
C
P.
C
P.
C
P.
C
E
E
TV
>>
or
GB
PREFERENCES SET-UP
Volume
Brightness
Colour
Contrast
resets to these preferences
TELEFUNKEN
IR download
( )No
Yes(+) PR
Teletext Fine Tuning Off On
Loading...