Teledyne HPM-760 User Manual
HPM-760s Installation
Figure below shows the Hastings piezo vacuum transducer. A standard 1/8” NPT male stem and
evacuation port is provided for system connection. VCR and KF stem terminations are also available.
When installing transducers with threaded stem, apply an approved vacuum sealant to the stem
threads of the transducer. Hand thread transducer
into vacuum system, until joint is finger tight.
Tighten transducer module completely using a
wrench on the hexagonal portion of the stem.
Do not grip instrument case to tighten; this will
result in permanent damage to transducer assembly. When the 760s is purchased independently of
the power supply/display, a connector is provided
so that the transducer can be connected as detailed
in the figure.
TRANSDUCER PIN-OUT
PIN 1................Signal Output (COM)
PIN 2................Signal Output (POS)
PIN 3................15-30 VDC Input (COM)
PIN 4................15-30 VDC Input (POS)
Manual may be obtained at:
http://www.teledyne-hi.com
Quick Start Guide_166-082010
ISO 9001
CERTIFIED
HPM-760s Installation
Figure below shows the Hastings piezo vacuum transducer. A standard 1/8” NPT male stem and
evacuation port is provided for system connection. VCR and KF stem terminations are also available.
When installing transducers with threaded stem, apply an approved vacuum sealant to the stem
threads of the transducer. Hand thread transducer
into vacuum system, until joint is finger tight.
Tighten transducer module completely using a
wrench on the hexagonal portion of the stem.
Do not grip instrument case to tighten; this will
result in permanent damage to transducer assembly. When the 760s is purchased independently of
the power supply/display, a connector is provided
so that the transducer can be connected as detailed
in the figure.
TRANSDUCER PIN-OUT
PIN 1................Signal Output (COM)
PIN 2................Signal Output (POS)
PIN 3................15-30 VDC Input (COM)
PIN 4................15-30 VDC Input (POS)
Manual may be obtained at:
http://www.teledyne-hi.com
Quick Start Guide_166-082010
ISO 9001
CERTIFIED
HPM-760s Installation
Figure below shows the Hastings piezo vacuum transducer. A standard 1/8” NPT male stem and
evacuation port is provided for system connection. VCR and KF stem terminations are also available.
When installing transducers with threaded stem, apply an approved vacuum sealant to the stem
threads of the transducer. Hand thread transducer
into vacuum system, until joint is finger tight.
Tighten transducer module completely using a
wrench on the hexagonal portion of the stem.
Do not grip instrument case to tighten; this will
result in permanent damage to transducer assembly. When the 760s is purchased independently of
the power supply/display, a connector is provided
so that the transducer can be connected as detailed
in the figure.
TRANSDUCER PIN-OUT
PIN 1................Signal Output (COM)
PIN 2................Signal Output (POS)
PIN 3................15-30 VDC Input (COM)
PIN 4................15-30 VDC Input (POS)
Manual may be obtained at:
http://www.teledyne-hi.com
Quick Start Guide_166-082010
ISO 9001
CERTIFIED
HPM-760s Installation
Figure below shows the Hastings piezo vacuum transducer. A standard 1/8” NPT male stem and
evacuation port is provided for system connection. VCR and KF stem terminations are also available.
When installing transducers with threaded stem, apply an approved vacuum sealant to the stem
threads of the transducer. Hand thread transducer
into vacuum system, until joint is finger tight.
Tighten transducer module completely using a
wrench on the hexagonal portion of the stem.
Do not grip instrument case to tighten; this will
result in permanent damage to transducer assembly. When the 760s is purchased independently of
the power supply/display, a connector is provided
so that the transducer can be connected as detailed
in the figure.
TRANSDUCER PIN-OUT
PIN 1................Signal Output (COM)
PIN 2................Signal Output (POS)
PIN 3................15-30 VDC Input (COM)
PIN 4................15-30 VDC Input (POS)
Manual may be obtained at:
http://www.teledyne-hi.com
Quick Start Guide_166-082010
ISO 9001
CERTIFIED
Loading...