Tektronix TLA Family Combined User/Service
xx
Tektronix Logic Analyzer Family
ZZZ
Product Safety & Compliance
Instructions
*P071259102*
071-2591-02
xx
Tektronix Logic Analyzer Family
ZZZ
Product Safety & Compliance
Instructions
www.tektronix.com
071-2591-02
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 500
Beaverto
USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, c all 1-800-833-9200.
Worl dwid e, v isit www.tektronix.com to find contacts in your area.
Table of Contents
General Safety Summary .......................................................................................... ii
Service Safety Summary...................................... .................................. .................. iv
Compliance Information........................................................................................... v
EMC Complia
Safety Compliance............................................................................................ vi
Environmental Considerations ........ .................................. ................................ ... viii
Preface .............................................................................................................. ix
Operating Requirements ........................................................................................... 1
TLA7012 Portable Mainframe Site Considerations............................................ ....... 3
TLA7016
Support Hardware Site Considerations .............. ................................ ................... 6
TLA5200B Series Logic Analyzer Site Considerations .............................................. 7
TLA7000 Series Basic Installation ............................................................................... 9
Chassis Ground Connections ............................ ................................ ..................... 9
Installing Modules in TLA7000 Series Mainframes . . ..... . ..... . ..... . ... . . . .... . . .... . ..... . ..... . ..... 10
ecting Accessories........................ ................................ .............................. 12
Conn
TLA5200B Series Basic Installation .................. ................................ .......................... 14
Chassis Ground Connections ............................ ................................ .................... 14
Connecting Accessories.................. ................................ .................................. .. 14
First Time Operation .............................................................................................. 16
nce............... ................................ ................................ ............... v
Benchtop Mainframe Site Considerations .......... ................................ ....... 3
Tektronix Logic Analyzer Family Product Safety & Compliance Instructions i
General Safety Summary
General Safet
To Avoid Fire or Personal
Injury
ySummary
Review the fo
this product or any products connected to it.
To avoid potential hazards, use this product only as specified.
Only qualified personnel should perform service procedures.
While using this product, you may need to access other parts of a larger system.
Read the safety sections of the other component manuals for warnings and
cautions related to operating the system.
Use proper power cord. Use only the power cord specified for this product and
certified for the country of use.
Use proper voltage setting. Before applying power, ensure that the line selector
is in the proper position for the source being used.
Connect and disconnect properly. Do not connect or disconnect probes or test
leads while they are connected to a voltage source.
Ground the product. This product is grounded through the grounding conductor
of the power cord. To avoid electric shock, the grounding conductor must be
connected to earth ground. Before making connections to the input o r output
terminals of the product, ensure that the product is properly grounded.
llowing safety precautions to avoid injury and prevent damage to
Observe all terminal ratings. To avoid fire or shock hazard, observe all ratings
and markings on the product. Consult the product manual for further ratings
information before making connections to the p roduct.
The inputs are not rated for connection to mains or Category II, III, or IV circuits.
Connect the probe reference lead to earth ground only.
Power disconnect. The power cord disconnects the product from the power source.
Donotblockthepowercord;itmustremain accessible to the user at all times.
Do not operate without covers. Do not operate this product with covers or panels
removed.
Do not operate with suspected failures. If you suspect that there is damage to thi
product, have it inspected by qualified service personnel.
Avoid exposed circuitry. Do not touch exposed connections and components when
power is present.
Replace batteries properly. Replace batteries only with the specified type and
rating.
Use proper AC adapter. Use only the AC adapter specified for this product.
Use proper fuse. Use only the fuse type and rating specified for this product.
s
ii Tektronix Logic Analyzer Family Product Safety & Compliance Instructions
General Safety Summary
TermsinThisManual
Symbols and Terms on the
Product
Do not operate i
Do not operate in an explosive atmosphere.
Keep product surfaces clean and dry.
Provide prop
details on installing the product so it has proper ventilation.
These terms may appear in this manual:
WAR NI NG .
in injury or loss of life.
CAUTION
damage to this product or other property.
These t
erms may appear on the product:
DANGER indicates an injury hazard immediately accessible as you read
the ma
n wet/damp conditions.
er ventilation. Refer to the manual’s installation instructions for
Warning statements identify conditions or practices that could result
. Caution statements identify conditions or practices that could result in
rking.
WARNING indicates an injury hazard not immediately accessible as you
the marking.
read
CAUTION indicates a hazard to property including the product.
The following symbol(s) may appear on the product:
Tektronix Logic Analyzer Family Product Safety & Compliance Instructions iii
Service Safety Summary
Service Safet
y Summary
Only qualifie
Safety Summary and the General Safety Summary before performing any service
procedures.
Do not service alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
Disconnect power. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
Use care when servicing with power on. Dangerous voltages or currents may exist
in this p
test leads before removing protective panels, soldering, or replacing components.
To avoi
d personnel should perform service procedures. Read this Service
roduct. Disconnect power, remove battery (if applicable), and disconnect
d electric shock, do not touch exposed connections.
iv Tektronix Logic Analyzer Family Product Safety & Compliance Instructions
Compliance Information
This section lists the EMC (electromagnetic compliance), safety, and
environmental standards with which the instrument complies.
EMC Compliance
EC Declaration of
Conformity
–EMC
Meets intent of Directive 2004/108/EC for Electromagnetic Compatibility.
Complianc
e was demonstrated to the following specifications as listed in the
Official Journal of the European Communities:
EN 61326-1:2006, EN 61326-2-1:2006. EMC requirements for electrical equipment
for measurement, control, and laboratory use.
12
CISPR 11:2003. Radiated and conducted emissions, Group A
IEC 61000-4-2:2001. Electrostatic discharge immunity
IEC 61000-4-3:2002. RF electromagnetic field immunity
IEC 610
00-4-4:2004. Electrical fast transient/burst immunity
IEC 61000-4-5:2001. Power line surge immunity
IEC 61000-4-6:2003. Conducted RF immunity
IEC 61000-4-11:2004. Voltage dips and interruptions immunity
3
EN 61000-3-2:2006. AC power line h armonic emissions
EN 61000-3-3:1995. Voltage changes, fluctuations, and flicker
European Contact.
Tektronix UK, Ltd.
Western Peninsula
estern Road
W
Bracknell, RG12 1RF
United Kingdom
1
This product is intended for use in nonresidential areas only. Use in residential areas may cause electromagnetic
interference.
2
Emissions which exceed the levels required by this standard may occur when this equipment is connected to a
test object.
3
Performance Criterion C applied at the 70%/25 cycle Voltage-Dip and the 0%/250 cycle Voltage-Interruption test
levels (IEC 61000-4-11).
Tektronix Logic Analyzer Family Product Safety & Compliance Instructions v
Compliance Information
Australia / New Zealand
Declaration of
Conformity – EMC
Safety Compliance
EC Declaration of
Conformity – Low Voltage
U.S. Nationally Recognized
Testing Laboratory Listing
Complies with t
he EMC provision of the Radiocommunications Act per the
following standard, in accordance with ACMA:
CISPR 11:2003
. Radiated and Conducted Emissions, Group 1, Class A, in
accordance with EN 61326-1:2006 and EN 61326-2-1:2006.
Compliance was demonstrated to the following specification as listed in the
Official Journal of the European Communities:
Low Voltage Directive 2006/95/EC.
EN 61010-1: 2001. Safety requirements for electrical equipment for
measurement control and laboratory use.
UL 61010
equipment.
1
TLA701
edition, Standard for electrical measuring and test equipment.
-1:2004, 2
1
6 Benchtop Mainframes and TLA5200B Series Logic Analyzers comply with UL61010B-1:2003, 1
nd
Edition. Standard for electrical measuring and test
st
Canadian Certification
Additional Compliances
Equipment Type
Safety Class
Safety Certification of
Plug-in or VXI Modules
CAN/CSA-C22.2 No. 61010-1:2004. Safety requirements for electrical
equipment for measurement, control, and laboratory use. Part 1.
1
TLA7016 Benchtop Mainframes and TLA5200B Series Logic Analyzers comply with CAN/CSA C22.2 No.
61010.1–97, 1
use. Part 1.
st
edition, Second Amendment. Safety requirements for measurement, control, and laboratory
1
IEC 61010-1: 2001. Safety requirements for electrical equipment for
measurement, control, and laboratory use.
Test and measuring equipment.
Class 1 – grounded product.
The safety certification is valid only when installed in an appropriately approved
(by a USA NRTL or a Canada Certified Organization) mainframe.
vi Tektronix Logic Analyzer Family Product Safety & C ompliance Instructions
Loading...