xx
TF-XGbT Compliance Test Fixture
(For use with TekExpress XGbT-10GBASE-T Automated
ZZZ
Solutions)
Reference
www.tek.com
077-0390-04
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun D rive
P.O. Box 500
Beaverto
USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, call 1-800-833-9200.
Worldwide, visit www.tek.com to find contacts in your area.
Warranty
Tektronix warrants that the product will be free from defects in materials and workmanship for a period of three (3)
years from the date of original purchase from an authorized Tektronix distributor. If the product proves defective
during this warranty period, Tektronix, at its option, either will repair the defective product without charge for
parts and labor, or will provide a replacement in exchange for the defective product. Batteries are excluded from
this warran
reconditioned to like new performance. All replaced parts, modules and products become the property of Tektronix.
ty. Parts, modules and replacement products used by Tektronix for warranty work may be new or
In order to o
of the warranty period and make suitable arrangements for t he performance of service. Customer shall be
responsible for packaging and shipping the defective product to the service center designated by Tektronix,
shipping charges prepaid, and with a copy of customer proof of purchase. Tektronix shall pay for the return of the
product to Customer if the shipment is to a location within the country in which the Tektronix service center is
located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any other charges for
product
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate
mainte
resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product;
b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any damage
or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been modified or
integrated with other products when the effect of such modification or integration increases the time or difficulty
of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY
OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY
LIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
IMP
TEKTRONIX' RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE
AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY.
TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS
ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
btain service under this warranty, Customer must notify Tektronix of the defect before the expiration
s returned to any other locations.
nance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage
[W16 – 15AUG04]
Table of Contents
Environmental Considerations .................................................................................... ii
General Information..................... .................................. ................................ ......... 1
TF-XGbT Product Features................ ................................ ................................ ... 1
TF-XGbT Sup
Characteristics Information ............. ................................ ................................. 4
Recommended Tektronix Oscilloscopes and Accessories.. . . .... . ..... . ..... . .... . ..... . ..... . .... . . .... . 4
XGbT 10GBASE-T Compliance Testing ............. .................................. ......................... 6
Clock Frequency, Droop, Jitter-Master, Linearity, and Power Spectral Density Measurements ..... . 6
Jitter-Slave Measurement .... . ..... . .... . ..... . ..... . ..... . .... . . .... . ..... . ..... . ..... . .... . ..... . ..... . .... 10
Return L
Ordering Information.............................................................................................. 16
plied Components ............................................................................ 1
oss Measurement ............................... ................................ .................... 13
TF-XGbT Compliance Test Fixture i
Environmental Considerations
Environmenta
Product End-of-Life
Handling
Restriction of Hazardous
Substances
l Considerations
This section
Observe the following guidelines when recycling an instrument or component:
Equipment Recycling. Production of this equipment required the extraction and
use of natu
harmful to the environment or human health if improperly handled at the product’s
end of life. In order to avoid release of such substances into the environment and
to reduce the use of natural resources, we encourage you to recycle this product
in an appropriate system that will ensure that most of the materials are reused or
recycled appropriately.
This product has been classified as Monitoring and Control equipment, and is
outside the scope of the 2002/95/EC RoHS Directive.
provides information about the environmental impact of the product.
ral resources. The equipment may contain substances that could be
This symbol indicates that this product complies with the applicable European
Union requirements according to Directives 2002/96/EC and 2006/66/EC
on waste electrical and electronic equipment (WEEE) and batteries. For
information about recycling options, check the Support/Service section of the
Tektronix Web site (www.tektronix.com).
ii TF-XGbT Compliance Test Fixture
General Information
This document provides a quick reference to the TF-XGbT Test Fixture and its
use with the Tektronix TekExpress XGbT-10GBASE-T Automated Solutions.
TF-XGbT Product Features
The TF-XGbT Test Fixture provides easy access to 10GBASE-T electrical signals
to perform
covered under sub clause 55.5.3 & 55.8.2.1 of IEEE Standard 802.3an-2006. This
fixtureisusedtoprovidefastandaccuratedesigndebuggingandvalidation.
The TF-XGbT test fixture offers following capabilities:
conformance testing and device characterization for measurements
Support f
Support for wide spectrum of tests saves time
On-board test points for accurate removal of disturbing signals ensures
reliable results
Return Loss Calibration Board reduces testing time
Test Channel for 10GBASE-T Jitter Slave tests ensures tests as per standard
or 10GBASE-T technologies enables comprehensive testing
F-XGbT Supplied Components
T
The components that are required to perform the XGbT-10GBASE-T transmitter
tests are listed as follows:
TF-XGbT Compliance Test Fixture 1
General Information
Table 1: TF-XGb
Sl
number Part number TF- XGbT test fixture Quantity Description
1
T supplied components
XGbT test fixture main
board
1
Themaintestfixture consists of three sections:
TC1, TC2, and
Section TC1: For Droop, Transmitter Timing
Jitter-Master, Transmit Clock Frequency,
Transmitte
Spectral Density (PSD) and Power Level
compliance test measurements.
NOTE. Inclu
Adapters and eight 50 ohms SMA terminators
mounted on the SMA connectors.
Section TC
compliance test measurement.
NOTE. Includes two SMA Male-to-Female
Adapters
Section TC3: Return Loss compliance test
measurement.
mounted on the SMA connectors.
NOTE. In
Adapters mounted on the SMA connectors.
2 878-156
3 174-7388-xx RJ45 Patch cord 2
4 174-7
5
6 174-7080-xx
7
8 015-0796-00
9 015-0795-xx
10
321-8010-xx
131-0993-xx
2-xx
079-xx
XGbT test fixture
calibration board
Cable assembly
50 Ω terminator SMA
le Assy; Patch
Cab
n, Shunt
Con
A adapter
SM
apter, Conn
Ad
hina RoHS sheet
C
1
6
6
1
8 2 pos, 2.54 mm pitch
2
12
1
Section TC3A: For return loss calibration.
Shielded CAT6, RJ45, cables to connect the Test
re to the return loss calibration board and
Fixtu
Device Under Test.
Dual SMA male to male Cable Assy, Length - 1 Ft
(To connect AWG to Return Loss Test Fixture).
To terminate the unused pairs on main test fixture
d.
boar
6, RJ45, shielded, 12 inches
CAT
A (F-F) adapter.
SM
A Male to SMA Female, straight
SM
ektronix Supplemental Product Information
T
Sheet for the People's Republic of China
(071-2179-XX).
TC3.
r Linearity, and Transmitter Power
des eight SMA Male-to-Female
2: Transmitter Timing Jitter-Slave
cludes two SMA Male-to-Female
2 TF-XGbT Compliance Test Fixture
General Information
NOTE. SMA conne
12-inch SMA male cable with P7380SMA probe.
CAT-6 3-inch S
Fixture to the return loss calibration board. CAT-6 Cable supports up to 250 MHz
bandwidth and supports 10GbE applications.
CAT-6 RJ-45 connectors are used in the test fixture, CAT-6 connectors are made
to higher standards that help reduce noise caused by crosstalk and system
interference.
Berg sticks shall also be used to probe differential signals using the P6330 probe.
ctors shall be used to probe the differential signals using
hielded RJ45 cables shall be used to connect the TF-XGbT Test
TF-XGbT Compliance Test Fixture 3
General Information
Characteristics
Information
The following e
test fi xture:
Table 2: Elect
Description Specification
Bandwidth
Attenuatio
master and slave in Jitter
(2 GHz bandwidth)
Isolation (between
transmitt
Insertion loss 0 - 500 MHz <0.9 dB
RJ45 Shielded Patch cord CAT-6A
n between the
er and Pair D)
lectrical characteristics are the specification of the TF-XGbT
rical characteristics
2GHz
15 dB ± 1 dB
>30dB
500 MHz - 1 GHz
1GHz-2GHz
Recommended Tektronix Oscilloscopes and Accessories
3: Recommended oscilloscopes and accessories
Table
Oscilloscope Accessories
DPO/DSA70404B P7380SMA / Matched-pair SMA cables (TCA-SMA connector)
DPO/DSA70604B P6330/P7330/P7350/ P7380SMA / Matched-pair
SMA cables (TCA-SMA connector)/P7520, P7516,
3A, P7508, P7506, and P7504 (TriMode
P751
probes)/P7350SMA/P7380SMA/P7313SMA
DPO/DSA70804B P6330/P7330/P7350/P7350SMA/P7380SMA/P7313SMA/
Matched-pair SMA cables (TCA-SMA connector)/P7520,
516, P7513A, P7508, P7506, and P7504 (TriMode
P7
probes)/P7350SMA/P7380SMA/P7313SMA
DPO/DSA71254B P6330/P7330/P7350/P7350SMA/P7380SMA/P7313SMA/
Matched-pair SMA cables (TCA-SMA connector)/P7520,
7516, P7513A, P7508, P7506, and P7504 (TriMode
P
probes)/P7350SMA/P7380SMA/P7313SMA
DPO/DSA71604B P6330/P7330/P7350/P7350SMA/P7380SMA/P7313SMA/
Matched-pair SMA cables (TCA-SMA connector)/P7520,
P7516, P7513A, P7508, P7506, and P7504 (TriMode
probes)/P7350SMA/P7380SMA/P7313SMA
DPO/DSA72004B P6330/P7330/P7350/P7350SMA/P7380SMA/P7313SMA/
Matched-pair SMA cables (TCA-SMA connector)/P7520,
P7516, P7513A, P7508, P7506, and P7504 (TriMode
probes)/P7350SMA/P7380SMA/P7313SMA
<1.5 dB
<3 dB
4 TF-XGbT Compliance Test Fixture
General Information
Table 3: Recommended oscilloscopes and accessories (cont.)
Oscilloscope Accessories
MSO70404 P6330/P7330/P7350/P7350SMA/P7380SMA/P7313SMA/
Matched-pair SMA cables (TCA-SMA connector)/P7520,
P7516, P7513A, P7508, P7506, and P7504 (TriMode
probes)/P7350SMA/P7380SMA/P7313SMA
MSO70604 P6330/P7330/P7350/P7350SMA/P7380SMA/P7313SMA/
Matched-pair SMA cables (TCA-SMA connector)/P7520,
P7516, P7513A, P7508, P7506, and P7504 (TriMode
probes)/P7350SMA/P7380SMA/P7313SMA
MSO70804 P6330/P7330/P7350/P7350SMA/P7380SMA/P7313SMA/
Matched-pair SMA cables (TCA-SMA connector)/P7520,
P7516, P7513A, P7508, P7506, and P7504 (TriMode
probes)/P7350SMA/P7380SMA/P7313SMA
MSO71254 P6330/P7330/P7350/P7350SMA/P7380SMA/P7313SMA/
Matched-pair SMA cables (TCA-SMA connector)/P7520,
P7516, P7513A, P7508, P7506, and P7504 (TriMode
probes)/P7350SMA/P7380SMA/P7313SMA
MSO71604 P6330/P7330/P7350/P7350SMA/P7380SMA/P7313SMA/
Matched-pair SMA cables (TCA-SMA connector)/P7520,
P7516, P7513A, P7508, P7506, and P7504 (TriMode
probes)/P7350SMA/P7380SMA/P7313SMA
MSO72004 P6330/P7330/P7350/P7350SMA/P7380SMA/P7313SMA/
Matched-pair SMA cables (TCA-SMA connector)/P7520,
P7516, P7513A, P7508, P7506, and P7504 (TriMode
probes)/P7350SMA/P7380SMA/P7313SMA
TF-XGbT Compliance Test Fixture 5
XGbT 10GBASE-T Compliance Testing
XGbT 10GBASE-
T Compliance Testing
ClockFrequency,Droop,Jitter-Master,Linearity,andPowerSpectralDensity
Measurements
The test set
and Power Spectral Density as described in IEEE 802.3an-2006 using SMA probe
(differential source), Differential probe (differential source), and SMA cable
(single-ended source) is as follows:
up for performing Clock Frequency, Droop, Jitter-Master, Linearity,
6 TF-XGbT Compliance Test Fixture
XGbT 10GBASE-T Compliance Testing
Connections wi
th SMA
Probe (Differential Source)
TF-XGbT Compliance Test Fixture 7
XGbT 10GBASE-T Compliance Testing
Connection wit
ha
Differential Probe
(Differential Source)
8 TF-XGbT Compliance Test Fixture
XGbT 10GBASE-T Compliance Testing
Connections wi
th SMA
Cables (Single-Ended
Source)
TF-XGbT Compliance Test Fixture 9
XGbT 10GBASE-T Compliance Testing
Jitter-Slave
Connections with SMA
Probe (Differential Source)
Measurement
The test setup for performing Jitter-Slave Measurement as described in IEEE
802.3an-2006 using an SMA probe (differential source), D ifferential probe
(differenti
al source), and SMA cable (single-ended source) is as follows:
10 TF-XGbT Compliance Test Fixture
XGbT 10GBASE-T Compliance Testing
Connection wit
ha
Differential Probe
(Differential Source)
TF-XGbT Compliance Test Fixture 11
XGbT 10GBASE-T Compliance Testing
Connections wi
th SMA
Cables (Single-Ended
Source)
12 TF-XGbT Compliance Test Fixture
Return Loss Measurement
The application ensures that the calibration is done at least once on the selected
lane before performing the Return Loss Measurement. When the measurement
is selected, a dialog box appears. Select live calibration or use the existing
calibrated files.
You can either verify if the Short, Load, and Open calibration factors are good
enough and then apply these calibrated values for performing the measurement, or
directly a
The test setup for calibrating and performing the Return Loss Measurement as
describe
XGbT 10GBASE-T Compliance Testing
pply the calibrated factors for the Return Loss measurement.
d in IEEE 802.3an-2006 using a differential probe is as follows:
TF-XGbT Compliance Test Fixture 13
XGbT 10GBASE-T Compliance Testing
Connection for
the measurement
calibrating
NOTE. is used to denote short jumpers.
14 TF-XGbT Compliance Test Fixture
XGbT 10GBASE-T Compliance Testing
Return loss mea
surement
setup
NOTE. is used to denote short jumpers.
TF-XGbT Compliance Test Fixture 15
Ordering Information
Ordering Info
XGbT 10GBASE-T
Automation Solution
To Order Alon
Oscilloscope
To Upgrade for Existing
Oscillos
XGbT Tes
gwith
cope
tFixture
rmation
Includes. Application CD, electronic documentation, and USB flash drive.
The options are as follows:
Opt. TEKEXP
Opt. XGbT
DPO/DSA70000 (TEKEXP). Order DPO7UP
DPO/DSA70000 (XGbT). Order DPO7UP
TF-XGbT. XGbT Test Fixture
16 TF-XGbT Compliance Test Fixture
Loading...