Tektronix Tektronix MDO Training/Tutorials

xx

Tektronix MDO Demo 1 Board

ZZZ

Instruction Manual

www.tektronix.com

*P071292400*

071-2924-00

Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are
protected by na

tional copyright laws and international treaty provisions.

Tektronix pro
previously published material. S pecifications and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

ducts are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all

Contacting Tektronix

Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA

For product information, sales, service, and technical support:

In North America, call 1-800-833-9200.
Worldwide, visit www.tektronix.com to find contacts in your area.

Table of Contents

Preface................................................................................................................................. ii

Compliance I

Installati

Operation............................................................................................................................... 3

Signal Descriptions .. .. . .. . ... ... . .. . .. . .. . .. . .. . .. . . .. . .. . .. . .. . .. . .. . .. . ... ... . .. . .. . .. . .. . .. . .. . ... ... . .. . .. . .. . .. . .. . .. . . . . . ....... 5

nformation............................................................................................................... ii

Environmental Considerations................................................................................................... ii

Preventing Electrostatic Damage................................................................................................ ii

on..............................................................................................................................1

Table of Content

s

Tektronix MDO Demo 1 Board Instruction Manual i

Compliance Info

rmation

Preface

The MDO Demo 1 board provides signals that you can use to show key features of Tektronix MDO4000 Series oscilloscopes.

Compliance Information

Environmental Considerations

This section provides information about the environmental impact of the product.

Product End-of-Life Handling

Observe the following guidelines when recycling an instrument or component:

Equipmen

may contain substances that could be harmful to the environment or human health if improperly handled at the product’s
end of life. In order to avoid release of such substances into the environment and to reduce the use of natural resources,
we encou
or recycled appropriately.

t recycling.

rage you to recycle this product in an appropriate manner that will ensure that most of the materials are reused

This sym
to Directives 2002/96/EC and 2006/66/EC on waste electrical and electronic equipment (WEEE) and
batteries. For information about recycling options, check the Support/Service section of the Tektronix Web
site (w

Production of this equipment required the extraction and use of natural resources. The equipment

bol indicates that this product complies with the applicable European Union requirements according

ww.tektronix.com).

Restriction of Hazardous Substances

This product has been classified as Monitoring and Control equipment, and is outside the scope of the 2002/95/EC RoHS
Directive.

Preventing Electrostatic Damage

trostatic discharge (ESD) can damage components on the demo board. To prevent ESD:

Elec

ot touch exposed components or connector pins unless you are using ESD protective measures, such as wearing

Do n
an antistatic wrist strap.

Handle the demo board as little as possible.

Do not slide the demo board over any surface.

Transport and store the demo board in a static-protected bag or container.

ii Tektronix MDO Demo 1 Board Instruction Manual

Installation

1. Plug the dual USB A connectors from

one end of the “
comes with your board, into two USB
ports of a PC or an oscilloscope. Do
this before p
connector from the other end of the U SB
cable into the MDO Demo 1 board.

You need to a
connectors to provide adequate power
to the demo board.

2. Plug the single B connector from the
other end of the USB cable into the demo
board. Two green and one red LEDs
on the board turn on and remain steady
when you apply adequate power to the
board.

If you plug the single B connector to the
demo board when there is just one of the
two USB A connectors attached to the
PC or oscilloscope, you may cause an
over-current (>500 mA) condition. This
can generate an error message.

Installation

T” USB cable, which

lugging the single USB B

ttach both USB A

3. Connect the MDO4000 Series
oscilloscope RF input to the MDO Demo
1 Board RF output using the N-to-BNC
Adapter (103–0045–00) and a 50 Ω coax
BNC cable.

Tektronix MDO Demo 1 Board Instruction Manual 1

Installation

4. Connect one or more analog probes,
if desired, from the MDO4000 Series
oscilloscope

to the desired connector or

connectors on the Demo 1 Board.

NOTE. The Tektronix MDO Demo 1 board requires approximately 0.75 A to operate.

NOTE. The purpose of the USB cable is to provide power to the demo board. No communication occurs over the USB cable.

All available signals (except for single-shot) are present on their connectors when you apply power to the demo board.

Push the RESET button immediately after connecting power.

2 Tektronix MDO Demo 1 Board Instruction Manual