Tektronix TDSUSB2 Reference manual
Getting Started with TDSUSB2
You can use this side of the Quick Reference to start taking
measurements with the USB2.0 Compliance T est Package
(TDSUSB2). The other side contains a complete menu tree
for TDSUSB2 software.
NOTE. For complete operating instructions
and General Safety information, refer to the
Online Help for the application.
The application displays results as a summary and as an
eye diagram as shown below.
The package includes an application (Universal Serial Bus
measurements software) and an optional USB2.0
comprehensive compliance test fixture.
The design of the package helps you to test if USB2.0
devices meet the compliance test requirements of the
USB2.0 industry for physical layer measurements. The
package supports these tests: Signal Quality, Inrush current
test, Droop test, Chirp and Receiver sensitivity testing,
Suspend, Resume, Reset from High Speed, Reset from
Suspend, and Packet Parameter tests.
Performing Signal Quality Test
1. Select File > Run Application > in the oscilloscope
menu bar. Then select TDSUSB2.0 Test Package,
App > USB2.0 Test Package, or
Analyze > USB2.0 T est Package.
2. Connect the device under test (DUT) to the Device SQ
section of the test fixture.
4. Select Measurement > Configure and set up the
application in the Configure and Source tabs.
6. Select Results > Details to view the results in a statistical
format.
5. Push the “Running Man” button to start taking
measurements.
3. Select Measurement > Select and choose a test for the
appropriate signal speed (Low, Full or High speed).
TDSUSB2 Ordering Information
This application supports TDS5000/B (except TDS5052/B
and TDS5032/B), TDS6604, TDS6404, TDS6604B,
TDS6804B, TDS6124C, TDS6154C, TDS/CSA7000/B,
DPO7000, and DPO70000 series oscilloscopes; refer to the
Optional Applications Software on Windows-Based
Oscilloscopes Installation Manual for a list of specific
models. The applications CD includes a PDF file of the
installation manual.
If you order Option USB with a new oscilloscope:
H USB 2.0 Universal Serial Bus Measurements Software is
installed and enabled
To order for an existing Windows-based oscilloscope:
H Order the CSA7UP Option USB (software only)
H Order the CSA7BUP Option USB (software only)
H Order the TDS5UP Option USB (software only)
H Order the TDS5BUP Option USB (software only)
H Order the TDS6UP Option USB (software only)
H Order the TDS6BUP Option USB (software only)
H Order the TDS7UP Option USB (software only)
H Order the TDS7BUP Option USB (software only)
H Order the DPO7UP Option USB (software only)
If you order TDSUSBF
H USB 2.0 Compliance Test Fixture only
Recommended Accessories
H TDSUSBF USB2.0 Compliance Test Fixture
H DTG5000 series with the M21 module
H DG2040 Data Generator*
H AWG610 Arbitrary Waveform Generator*
H TDS8000 series oscilloscope with an 80E04 Time Do-
main Reflectometer (TDR) Sampling Module
H P6248 Differential Probe
H TCP202 or TCP0030 Current Probe
H P6245, TAP1500 or P6243 Single-Ended Probes
* DG2040 and AWG610 are discontinued.
NOTE. To test High Speed USB2.0 devices,
you can use this application with DPO7254,
DPO/DSA70404, DPO/DSA70604,
DPO/DSA70804, DPO/DSA72004,
DPO/DSA71604, DPO/DSA71254,
TDS6404, TDS6804B, TDS6604/B,
TDS6804B, TDS6124C, TDS6154C,
TDS7404/B, CSA7404/B, TDS7704B, and
TDS7254/B oscilloscopes.
Generating a Compliance Report
To produce a compliance test report, select Utilities > Report
Generator.
For up-to-date information on Tektronix oscilloscope
solutions for USB2.0 compliance testing, access the
www.tektronix.com/Measurement/scopes/
Web page.
TDSUSB2
Universal Serial Bus Package
Reference
www.tektronix.com
*P071188203*
071-1882-03
TDSUSB2 Menu Tree
File
Recall Default
Recall
Save
Preferences
Recently Recalled
Recently Saved
Minimize
Exit
General | Advanced
Low Speed | Full Speed
OK
Apply
Cancel
Signal Quality Check
Device IDs
Device Description
Generate Automatic IDs
Inrush
Eye Diagram
Signal Rate
Paired JK Jitter
Paired KJ Jitter
Consecutive Jitter
EOP Width
CrossOver
Rise Time
Fall Time
Select All
Inrush Current
Measurements
Control Menu
Configure
Select
Configure
Run
Hide
Exit
Signal Quality Check
Inrush Current Check
Droop Test
Receiver Sensitivity
High Speed
Configure
Source
Configure
Source
Port
Hub
Configure Limits
Select Source
Source
Droop
Configure
Signal Quality Check
Receiver Sensitivity
Chirp
Inrush
Droop
Device IDs
Device Description
Generate Automatic IDs
More
Configure
Tier
Signal Direction
Test Point
Configure Levels
Configure Limits
Live/Ref
From File (Browse)
Tier
V bus
Device Type
Configure Limits
Live / Ref From File (Browse)
V bus Source
Bus Powered
Self Powered
Max
Min
Default
Set
Cancel
Live / Ref From
File (Browse)
Live
Droop Test
Eye Diagram
Signal Rate
Monotonic Property
EOP Width
Rise Time
Fall Time
Select All
Inrush Current
Droop Test
Receiver Sensitivity
Suspend
Chirp
Resume
Reset from High
Speed
Reset from
Suspend
Packet
Parameter
Upstream
Downstream
Near End
Far End
Rise Time / Fall Time
Monotonic Property
Max
Min
Default
Set
Cancel
Differential
Single Ended
Qualify Channel
Manual Entry
Max
Min
Default
Set
Cancel
Results
Utilities
Help
Chirp
Suspend
/Resume
Reset from
Suspend/
Reset from
Resume
Packet
Parameter
Summary
Details
Deskew
Report Generator
TSV File Generator
Help Topics
About TDSUSB2
Source
Configure
Source
Configure
Source
Configure
Source
Configure
Eye Diagram
Waveform Plot
Eye Diagram
Waveform Plot
From | To
Slope
Edges
Perform Deskew
Report Format
Generation
Report Directory (Browse)
Report file name
Generate
CSV
Live
TSV Destination File (Browse)
Convert
Live/Ref
DUT
Live/Ref
Signal
Direction
Live/Ref
Signal
Direction
Live/Ref
DUT
Source
Ref Level
Hysteresis
Rise
Fall
Tektronix Specific
Plug−Fest Specific
CSV Format
Automatic
Manual
CSV Source
Host
Device
Upstream
Downstream
Upstream
Host
Device
CSV File Type
D+ (Browse)
D− (Browse)
EL_33, EL_34
EL_35
EL_28, EL_29, EL_31
EL_21, EL_23,EL_25
EL_22
EL_55
EL_21, EL_22,EL_25
EL_22
Copyright Tektronix, Inc.
Loading...