Tektronix TCA-292D User manual

ZZZ

TCA292D
Adapter

Instructions

Do not operate wi

suspect there is damage to this product, have it
inspected by qua

Do not operate i

Do not operate in an explosive atmosphere.

Keep product su

Safety sym bols on the product

Environmental C onsiderations

This section provides information about the
environmental impact of the product.

th suspected failures. If you

lified service personnel.

n wet/damp conditions.

rfaces clean and dry.

Equipment Recycling. This product
complies with the European Union’s
requirements according to Directive
2002/96/EC on waste electrical and
electronic equipment (WEEE). For
more information about recycling
options, check the Support/Service
section of the Tektronix Web site
(www.tektronix.com).

Removing the Ada

1. Disconnect the 2.92 mm or SMA cable from
the device under

2. Disconnect the 2.92 mm or SMA cable from
the adapter.

3. Unscrew the screw that holds the adapter
in place.

4. Press the button on top of the a dapter to
release the lock and remove the adapter
from t he host instrument. (See Figure 2.)

NOTE. It may be necessary to remove the adapter
before installing the host instrument cover.

pter

test.

*P071299001*

071-2990-01

Safety Summary

To avoid potential hazards, use this product only
as specified.

To avoid fire or personal injury

Connect and disconnect properly. Connect

the adapter to the host instrument before
connecting the 2.92 mm or SMA device to the
device-under-test. Disconnect the device input
and ground from the device-under-test before
disconnecting the 2.92 mm or SMA device from
the adapter and host instrument.

Ground the product. This product is indirectly
grounded through the grounding conductor
of the host instrument power cord. To avoid
electric shock, the grounding conductor must
be connected to earth ground. Before making
connections to the input or output terminals of
the product, ensure that the product is properly
grounded.

Observe all terminal ratings. To avoid fire or
shock hazard, observe all ratings and markings
on the host instrument. Consult the host
instrument documentation for further ratings
information before making connections to the
host instrument.

Do not apply a potential to any terminal,
including the common terminal, that exceeds the
maximum rating of that terminal.

Do not operate without covers. Do not operate
this product with covers or panels removed.

Product Description

The TekConnect-292D adapter allows you to
connect 2.92 mm and SMA-terminated devices
to Tektronix instruments with the TekConnect
interface. The adapter preserves maximum signal
integrity and eliminates the need for additional
external adapters, which can degrade voltage
standing wave ratio (VSWR).

Figure 1: TCA292D Adapter

Using the Adapter

The adapter connects directly to the TekConnect
interface on the host instrument.

Installing the Adapter

1. Insert the adapter into the TekConnect
interface on the host instrument until the
adapter locks in place.

2. Finger-tighten the screw to secure the
adapter to the instrument.

3. Connect a 2.92 mm or SMA cable to the
adapter.

4. Connect the other end of the 2.92 mm or
SMA cable to the device under test.

Figure 2: Removing the adapter from the host
instrument

CAUTION. Electrostatic discharge (ESD) can
damage the instrument input. Use antistatic
precautions when using this adapter.

Specifications

Maximum Input Voltage. The lesser of 30 V

or the maximum input voltage rating for the
TekConnect host instrument.

VSWR. Refer to the TekConnect host instrument
for the overall system VSWR.

Propagation Delay. 142 ps ±4 ps.

Additional Information

For additional information on using the
TekConnect adapters, refer to the documentation
for the host instrument.

Warranty Information

For warranty information, go to
www.tektronix.com, click Support, and
then, in Product Support, enter the product
nomenclature and look up tektronix warranty.

Contacting Tektronix

Tektronix, Inc.
14200 SW Karl Braun Drive
PO Box 500 Beaverton, OR 97077 USA

For product information, sales, service, and
technical support:

In N orth America, call 1–800–833–9200.

Worldwide, visit www.tektronix.com to find
contacts in your area.

RMS

opyright © Tektronix, Inc. All rights reserved. www.tektronix.com

C