Teknatool NOVA 6039, NOVA 6040, NOVA 6006, NOVA JSCOLE Instruction Manual

NOVA

12” COLE JAWSET
COLE JAW EXTENSION ACCESSORY

Publication117-0815-002

SKU: 6039 / 6040

THIS MANUAL CONTAINS IMPORTANT INFORMATION
REGARDING SAFETY, OPERATION, MAINTENANCE AND
STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY
AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS
AND PRODUCT LABELS. FAILURE TO DO SO COULD RESULT IN
SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.THIS
ACCESSORY CAN ONLY BE USED ON NOVA CHUCKS.

Instruction Manual

117-0815-0021

CONTACT TEKNATOOL:

New Zealand

Teknatool International Ltd

Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.teknatool.com

United States

Teknatool Service Center

Phone: [phone]
Free Phone: [phone]
Free Fax: [phone]
Email: [e-mail]
Website: www.teknatool.com

117-0815-0022

TABLE OF CONTENTS:

CONTACT TEKNATOOL ...................................................................... 2

GENERAL SAFETY RULES ................................................................. 4

12" COLE, COLE and MINI COLE JAWS ............................................. 6

ADDING THE OPTIONAL ACCESSORY EXTENSION PIECE FOR 12”

COLE JAW ......................................................................................... 11

WARRANTY ....................................................................................... 12

117-0815-0023

GENERAL SAFETY RULES

!

!

PLEASE READ AND UNDERSTAND THESE SAFETY RULES BEFORE OPERATING ANY
OF THE ACCESSORY JAWS.

WARNING!The NOVA ACCESSORY JAWS ARE DESIGNED FOR USE ON

TEKNATOOL CHUCKS ONLY. THEY ARE NOT DESIGNED TO FIT AND CANNOT BE
USED WITH ANY OTHER CHUCK. TO DO SO COULD CAUSE A MALFUNCTION AND
RISK OF SERIOUS INJURY. IF YOU ARE UNSURE OF THE USE OR APPLICATION OF
ANY OF THESE ACCESSORY JAWS BEFORE USING CONTACT YOUR RESELLER OR
TEKNATOOL DIRECTLY.

IMPORTANT:READ VERY CAREFULLY THE SAFETY SECTION IN THE TEKNATOOL
CHUCK MANUAL BEFORE OPERATION AND FOLLOW CLOSELY THE SAFETY RULES
OUTLINES IN THIS JAW MANUAL.

CONSULT RELEVANT OPERATIONAL SECTIONS OF THE TEKNATOOL CHUCK MANUAL
BEFORE USING JAWS.

SOME SAFETY DIRECTIONS ARE PERTINENT ONLY TO A CERTAIN JAW SET. ANY
ADDITIONAL SAFETY INFORMATION IS LOCATED IN THE TEXT OF THE RELEVANT
ACCESSORY JAW IN THE PAGES FOLLOWING.

DANGER: THIS CHUCK IS CAPABLE OF CONTRIBUTING TO SERIOUS INJURY, AS

WITH ANY OTHER POWER TOOL ACCESSORY, IF USED IMPROPERLY ON THE LATHE.
Before using the Teknatool chuck and accessory jaws, read and understand the instruction

manuals. Read and understand also the lathe manual. If you do not have a manual, contact
the supplier of your lathe to obtain one before using the lathe and chuck.

User must be professionally trained to use chuck and accessory jaws. Vocational school
courses are recommended. As with any other chucking method, an extremely cautious and
sensible approach is necessary. With the Teknatool chuck it is not possible to give exact
directions as to the amount of tightening pressure required for work holding. Follow closely
strict guidelines in this manual for different jaw types for wood blank diameters length, and
turning speed.

117-0815-0024

ALWAYS WEAR EYE PROTECTION WHICH COMPLIES WITH CURRENT ANSI
STANDARD Z87.1 (USA). WE STRONGLY RECOMMEND THAT A FULL FACE SHIELD IS
USED AT ALL TIMES.

BEFORE USING THE TEKNATOOL CHUCK ACCESSORY JAWS BE SURE THAT:

 WARNING!!! EXCESSIVE SPEED IS A SERIOUS LATHE HAZARD. ALWAYS

TURN AT THE LOWEST SPEED POSSIBLE. Speed required will vary with wood

blank size. The larger the blank the slower the speed. Consult your lathe manual.
DO NOT ATTEMPT TO USE THE CHUCK UNLESS THE LATHE SPEEDS ARE
KNOWN. YOU MUST STRICTLY FOLLOW THE MAXIMUM SPEED LIMITS SET
OUT IN THE OPERATIONAL SECTIONS OF THIS MANUAL. DO NOT EXCEED
THEM UNDER ANY CIRCUMSTANCES.

 EXAMINE WOOD CAREFULLY. ONLY MOUNT SOUND WOOD. If any cracks or

weakness is found in the wood – DO NOT MOUNT IN CHUCK OR IN ACCESSORY
JAWS. DO NOT MOUNT WOOD THAT IS LIKELY TO BREAK UP DURING
TURNING (E.G. ROTTEN OR SPONGY WOOD). DO NOT USE POORLY
LAMINATED WOOD.

 DO NOT EXCEED MAXIMUM GUIDELINES IN THIS MANUAL FOR WOOD BLANK

DIAMETER / LENGTH FOR THE DIFFERENT MODES OF OPERATION AND JAW
TYPES.

 DO NOT EXTEND JAW SLIDES BEYOND CHUCK BODY UNDER ANY

CIRCUMSTANCES. ONLY OPERATE CHUCK WITH JAW SLIDE STOP SCREW IN
PLACE. This prevents jaw slides from dislodging from chuck. NOTE: SuperNova2
Chuck has automatic internal stop.

 WARNING - MAKE SURE THAT IN EXPANSION MODE THAT THE AMOUNT OF

TRAVEL REQUIRED IS LESS THAN THE LIMIT OF THE STOP SCREW, OR
AUTOSTOP. DO NOT TRY TO FORCE CHUCK OPEN FURTHER.

 ALWAYS TEST WORKPIECE IS GRIPPED SECURELY IN THE JAWS. BEFORE

OPERATION TEST BY WRENCHING WORKPIECE IN JAWS. IF ANY LOOSENING
OCCURS, RE-EXAMINE HOLDING AREA FOR ADEQUATE GRIP (following
mounting guidelines) AND ANY DAMAGE TO GRIPPING AREA.

 MAKE SURE WORKPIECE IS CLEAR OF OBSTRUCTION BY MANUALLY

ROTATING WORKPIECE BEFORE SWITCHING POWER ON.

117-0815-0025