Technaxx® * User Manual
Bluetooth Vinyl Record and Cassette Converter TX-22+
The manufacturer Technaxx Deutschland GmbH & Co.KG hereby declares that this device, to which this user manual belongs, complies with the essential requirements of the standards referred to the Directive RED 2014/53/EU. The Declaration of Conformity you find here: www.technaxx.de/ (in bar at the bottom “Konformitätserklärung”). Before using the device the first time, read the user manual carefully.
Service phone No. for technical support: 01805 012643 (14 cent/minute from German fixed-line and 42 cent/minute from mobile networks).
Free Email: support@technaxx.de
Keep this user manual for future reference or product sharing carefully. Do the same with the original accessories for this product. In case of warranty, please contact the dealer or the store where you bought this product. Warranty 2 years
Before usage
Choose the installation location of your unit carefully. Avoid placing it in direct sunlight or close to a source of heat. Also avoid locations subject to vibrations and excessive dust, heat, cold or moisture.
Do not install the unit in a inclined position, It is designed to be operated in a horizontal position only.
If the unit is brought directly from a cold to a warm location, moisture may condense inside the player, and cause damage it. When you first install the unit, or when you move it from a cold to a warm location, wait for 30 minutes before operating the unit.
The ventilation holes should not be covered. Make sure there is enough space above and beside the amplifier/receiver. Do not place a CD player or other equipment on top of the device.
Do not open the cabinet. This might cause a damage to circuitry or electrical shock.
If you are not going to use the player for long time, be sure do disconnect the player from the AC power source. When removing the power plug, never yank the cord.
To prevent fire or shock hazard, disconnect your unit from the AC power source when cleaning. Use caution when cleaning and wiping the plastic parts. Do not attempt to clean the unit with the chemical solvents as this might damage the finish.
1
Features
Digitizing vinyl records & audio cassettes to USB or SD card up to 32GB
Music playback & recording via Bluetooth 2.0
Recording from external devices via AUX-IN connection
Playback of MP3/WMA music files from USB or SD card up to 32GB
No computer/notebook required
RCA outputs for connection to HiFi systems
Record player with automatic stop & 3 speeds: 33, 45, 78 rpm
Built-in cassette player
Built-in stereo loudspeakers
LED display with backlight
Functional and easy handling
Technical specifications
Bluetooth |
V2.0 / profil A2DP & HFP / distance ~10m open areas |
|
Mode |
Phono, Cassette, USB, SD card, AUX–IN, Bluetooth |
|
Lautsprecher |
2x 2W stereo (Ø= 7cm), SNR 80dB, impedance 4Ω |
|
|
|
|
Frequency range |
Speakers 80Hz–15kHz |
|
Recording |
MP3 music files on USB or SD card up to 32GB |
|
Playback |
MP3/WMA music files from USB or SD card up to 32GB |
|
|
Belt-drive |
|
Mechanics |
Semi-automatic play tone pickup arm |
|
|
Ceramic stereo cartridge with sapphire stylus |
|
|
3.5mm AUX-IN jack & 3.5mm headphone jack |
|
Connections |
2x RCA outputs for connection to HiFi systems 400mV |
|
|
USB port & SD card slot (up to 32GB) |
|
Input device |
AC 220~240V / 0.8A |
|
Material |
MDF + PVC + Plastic |
|
Weight/Dimensions |
3kg / (L) 32.3 x (W) 31.1 x (H) 13.2cm |
|
Package Contents |
Bluetooth Vinyl Record and Cassette Converter TX-22+, |
|
45rmp single Puck adapter, User Manual |
||
|
2
Product Overview
Front View
1 |
Dust cover |
9 |
USB port |
|
|
|
|
2 |
Source/ Mode (USB/SD |
10 |
LCD display |
|
|
|
|
3 |
Record button |
11 |
Power LED indicator |
|
|
|
|
4 |
Function selector |
12 |
Play/Pause button |
|
|
|
|
5 |
AUX–IN jack |
13 |
Stop button |
|
|
|
|
6 |
Delete button |
14 |
Volume knob / ON / OFF |
|
|
|
|
7 |
3.5mm headphone jack |
15 |
Next/ Skip up button |
|
|
|
|
8 |
Folder/Program button |
16 |
Previous/ Skip down button |
|
|
|
|
|
|
17 |
SD card slot |
|
|
|
|
3
Top View
20 |
Right speaker |
24 |
Speed selectors (33/45/78 rpm) |
|
|
|
|
21 |
45 rpm adaptor |
25 |
Tone arm |
|
|
|
|
22 |
Lift lever |
26 |
Cassette player |
|
|
|
|
23 |
Auto stop control |
|
|
|
|
|
|
4
Rear View
27 |
RCA output |
28 |
AC power cord |
|
|
|
|
First start
Carefully read the user manual. Insert the USB power adapter of the device into a socket with AC 220–240V. Be reminded: “Non-connected devices always work faulty!”
Phono Mode
IMPORTANT! When using the turntable:
Make sure to remove the stylus protector, as illustrated on the left picture (it should easily slide off the stylus assembly).
Make sure to unclip the tone arm lock before use and to secure it again after use.
|
|
|
|
|
1 |
Cartridge |
2 |
Needle protection |
|
|
|
|
|
|
5
Playing in Phono mode (Vinyl)
1.Open the dust cover. Turn the volume knob (14) to turn the equipment on.
2.Use the function selector (4) to select PHONO mode.
3.Set the speed selector to the appropriate position: 33, 45 or 78, depending on the record to be played.
4.Set the auto stop control to ON if you want the turntable to stop turning when it has reached the end of the record. If the switch is set to OFF, the turntable will continue turning at the end of the record.
5.Place the record on the turntable (use the 45 rpm adaptor, if required).
6.Remove the needle protection. Move the lift lever towards the back to raise the tone arm from the arm park, then slowly move the arm to the record, as illustrated on the right picture above. The turntable will start rotating.
7.Move the lift lever towards the front, the tone arm will gently drop onto the record and playback will start.
8.To stop playback, move the lift lever towards the back to raise the tone arm. The turntable will still be rotating but the record will stop playing. To continue playback, move the lift lever towards the front.
9.To play a different piece on the record, move the lift lever towards the back, move the raised tone arm to the start of the piece and then move the lift lever towards the front to lower the tone arm and start playback.
10.To adjust the volume level, turn the volume knob to the right or left.
11.At the end of the record, move the lift lever towards the back to raise the tone arm and move it back to the tone arm park, and then move the lift lever towards the front to lower the arm onto its rest.
12.Alternatively, lift the tone arm off the record and return it to the arm rest manually.
13.When you have finished playing records, engage the tone arm lock to protect it from accidental movement. Turn the volume knob switch the unit off. Unplug it from the power supply if you are not going to use it for a while.
NOTE: Should your record stop before the last track finishes, set the auto stop control to OFF. Your record will now play to the end, but you will have to stop the turntable rotation manually. (Return the tone arm to its rest manually and if the turntable is still rotating, switch off the unit by pressing the volume control knob. Then set the auto stop control back to ON.)
6
Loading...