Teac Network USB DAC Integrated Amplifier, NP-H750 User Manual

CQX1A1707Z

Integrated Amplifier

Network /USB DAC

MANUAL DEL USUARIO

H750

ENGLISH

OWNER'S MANUAL

MODE D’EMPLOI

FRANÇAIS ESPAÑOL

IMPORTANT SAFETY PRECAUTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

For North American model:

This device complies with “Part 15 of FCC Rules” and “RSS-Gen of IC Rules”. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.

The lightning flash with arrowhead in an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous volt-

age” within the product’s enclosure that could be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point in an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

< DO NOT REMOVE EXTERNAL CASES OR CABINETS TO

EXPOSE THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE WITHIN!

IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT, CONTACT TEAC FOR A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS BEEN REPAIRED.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN COULD RESULT IN HAZARDOUS RADIATION EXPOSURE.

IN NORTH AMERICA USE ONLY ON 120 V SUPPLY.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

CAUTION

Changes or modifications to this equipment not expressly approved by TEAC CORPORATION for compliance will void the user’s warranty.

NOTE

For product available in the USA/Canada market, only channels 1 to 11 can be operated. Selection of other channels is not possible.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Information to the user:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the equipment and/or the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.

Radiation Exposure Statement

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment, meets the FCC radio frequency (RF) Exposure Guidelines, and RSS-102 of the IC radio frequency (RF) Exposure rules.

End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

Note

This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.

Q Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading to fire, injury or the staining of nearby things. Please read and observe the following precautions carefully.

o Be sure to insert the batteries with correct positive

(+) and negative (_) orientations.

o Use batteries of the same type. Never use different

types of batteries together.

o If the remote control is not used for a long time (more

than a month), remove the batteries to prevent them from leaking.

o If the batteries leak, wipe away the leakage inside

the battery compartment and replace the batteries with new ones.

o Do not use batteries of types other than those speci-

fied. Do not mix new batteries with old ones or use different types of batteries together.

o Do not heat or disassemble batteries. Never throw

batteries into fire or water.

o Do not carry or store batteries with other metallic

objects. The batteries could short circuit, leak or explode.

o Never recharge a battery unless it is confirmed to be

a rechargeable type.

Wi-Fi is a mark of the Wi-Fi Alliance. The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance.

This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft.

Windows, Windows Vista, Windows 7, Windows Media and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

“Made for iPod,” “Made for iPhone,” and “Made for iPad” mean that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards.

Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance.

Apple, Macintosh, Mac OS X, AirPlay, the AirPlay logo, iPad, iPhone, iPod, iPod nano, iPod touch and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries.

IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.

DLNA®, the DLNA Logo and DLNA CERTIFIED® are trademarks, service marks, or certification marks of the Digital Living Network Alliance.

Other company names, product names and logos in this document are the trademarks or registered trademarks of their respective owners.

NOTE: Open source software copyright and license infor-

mation is included at the end of this manual.

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

The apparatus draws nominal non-operating power

from the AC outlet with its POWER or STANDBY/ON switch not in the ON position. The mains plug is used as the disconnect device, the

disconnect device shall remain readily operable. Caution should be taken when using earphones or

headphones with the product because excessive sound pressure (volume) from earphones or headphones can cause hearing loss.

CAUTION

Do not expose this apparatus to drips or splashes.

Do not place any objects filled with liquids, such as

vases, on the apparatus. Do not install this apparatus in a confined space such

as a book case or similar unit. The apparatus should be located close enough to the

AC outlet so that you can easily reach the power cord plug at any time. If the product uses batteries (including a battery pack

or installed batteries), they should not be exposed to sunshine, fire or excessive heat. CAUTION for products that use replaceable lithium

batteries: there is danger of explosion if a battery is replaced with an incorrect type of battery. Replace only with the same or equivalent type.

WARNING

Products with Class construction are equipped with a power supply cord that has a grounding plug. The cord of such a product must be plugged into an AC outlet that has a protective grounding connection.

CLASS apparatus with double insulation, and no protective earth provided.

For European Customers

Pb, Hg, Cd

Disposal of electrical and electronic equipment

(a) All electrical and electronic equipment should be

disposed of separately from the municipal waste stream via collection facilities designated by the government or local authorities.

(b) By disposing of electrical and electronic equipment

correctly, you will help save valuable resources and prevent any potential negative effects on human health and the environment.

equipment can have serious effects on the environment and human health because of the presence of hazardous substances in the equipment.

(d) The Waste Electrical and Electronic

Equipment (WEEE) symbol, which shows a wheeled bin that has been crossed out, indicates that electrical and electronic equipment must be collected and disposed of separately from household waste.

(e)

Return and collection systems are available to end users. For more detailed information about the disposal of old electrical and electronic equipment, please contact your city office, waste disposal service or the shop where you purchased the equipment.

Disposal of batteries and/or accumulators

(a) Waste batteries and/or accumulators should be

disposed of separately from the municipal waste stream via collection facilities designated by the government or local authorities.

(b) By disposing of waste batteries and/or accumulators

correctly, you will help save valuable resources and prevent any potential negative effects on human health and the environment.

(c)

Improper disposal of waste batteries and/or accumulators can have serious effects on the environment and human health because of the presence of hazardous substances in them.

(d)

The WEEE symbol, which shows a wheeled bin that has been crossed out, indicates that batteries and/or accumulators must be collected and disposed of separately from household waste. If a battery or accumulator contains more than the specified values of lead (Pb), mercury (Hg), and/or cadmium (Cd) as defined in the Battery Directive (2006/66/EC), then the chemical symbols for those elements will be indicated beneath the WEEE symbol.

(e) Return and collection systems are available to end

users. For more detailed information about the disposal of waste batteries and/or accumulators, please contact your city office, waste disposal service or the shop where you purchased them.

ENGLISH

Contents

Before use

Thank you for choosing TEAC. Read this manual carefully to get the best performance from this unit.

Before use ......................................................6

Files ............................................................8

Connecting speakers ...........................................9

Connections ...................................................11

Names and functions of parts (main unit) ......................14

Names and functions of parts (remote control unit) ............16

Using the remote control unit .................................19

Playing back music on a computer .............................20

Setting the current time .......................................23

Basic operation ................................................24

About the ErP .................................................27

Listening files on a USB flash drive .............................27

Searching inside folders .......................................29

Information shown on the display .............................30

Shuffle playback ...............................................30

Repeat playback ...............................................31

Listening to an iPod/iPhone/iPad ..............................32

Initial network setup ...........................................34

Network configuration .........................................37

Listening to the Internet radio .................................38

Internet radio portal ...........................................41

Setting up the media player ...................................42

Listening with the media player ................................47

Using AirPlay ..................................................48

Using DLNA ...................................................49

Sleep Timer ....................................................50

Setting the wake-up timer .....................................50

Updating the firmware ........................................52

Troubleshooting ...............................................57

Restoring factory settings ......................................59

Specifications ..................................................60

Features of NP-H750

p USB port for iPod/iPhone/iPad/USB flash drives p Internet radio (page 38) p Media player (page 42) p AirPlay (page 48) p DLNA (page 49)

Tracks on a server connected to the network can be played back by computers and mobile devices if they have applications that support DLNA installed.

What’s in the box

Check to be sure the box includes all the supplied accessories shown below. Please contact the store where you purchased this unit if any of these accessories are missing or have been damaged during transportation.

Power cord × 1

Remote control unit (RC-1308) × 1

Batteries for remote control unit (AAA) × 2

Owner’s manual (this document) × 1

p Keep this manual in a safe place for future reference.

Warranty card × 1

CAUTION

Read this before attempting any operations.

p Avoid placing the unit in direct sunlight or close to any

source of heat, such as a radiator, heater, open fireplace or amplifier. Also avoid locations that are subject to vibrations or exposed to excessive dust, cold or moisture.

p This unit consumes energy when in standby. p Place the unit in a stable location near the audio system

that you will use.

p Be careful to avoid injury when moving the unit due to

its weight. Get someone to help you if necessary.

p The voltage supplied to the unit should match the volt-

age as printed on the rear panel. If you are in any doubt regarding this matter, consult an electrician.

p As the unit could become warm during operation, always

leave sufficient space around it for ventilation. When placing this unit, position it so that it is at least 30 cm (12”) from walls and other devices in order to allow good heat dissipation. When installing it in a rack, leave at least 30 cm (12”) open above and behind the unit. DO NOT place anything, not even CDs, CD-Rs, LP records or cassette tapes, on top of the unit.

p Do not open the body of the unit as this might result in

damage to the circuitry or cause electric shock. If a foreign object should get into the unit, contact your dealer or TEAC service company.

p When removing the power plug from the wall outlet,

always pull directly on the plug; never yank on the cord.

p Depending on the electromagnetic waves of television

broadcasts, interference might appear on television screens when this unit’s power is on. This does not indicate that this unit or the TV is malfunctioning. If this occurs, put the unit in standby.

Maintenance

If the surface of the unit gets dirty, wipe it with a soft cloth or use diluted mild liquid soap. Allow the surface of the unit to dry completely before using.

B For safety, disconnect the power cord from the

socket before cleaning.

p Never spray liquid directly on this unit.

p Do not use thinner or alcohol as they could damage the

surface of the unit.

p Avoid allowing rubber or plastic materials to touch this

product for long periods of time, because they could damage the cabinet.

ENGLISH

Files

Playable Files

This unit can play audio files that are on external USB flash drives.*

p USB flash drives must be formatted as FAT 16 or FAT 32,

but not NTFS.

* The USB port on this unit only supports USB flash

drives (also known as “thumb drives” and “jump drives”). It does not support standard USB hard drives.

The file formats that can be played back by each playback source are as follows.

Format

WAV

FLAC

MP3 OGG WMA

AAC

WAV

File extension: .wav Stream: LPCM Sampling Frequency: 8 kHz to 48 kHz

USB flash

drive

               

Media player

WiFi

Ethernet

cable

WMA

File extension: .asf/.wma Stream: WMA2/7/8/9/10, WMA Pro, WMA Lossless** Sampling Frequency: 8 kHz to 48 kHz Bit Rate: 5 kbps to 320 kbps ** WMA Pro and WMA Lossless formats are only supported

when the playback computer is using Windows Media Player 12 or later. (Playback occurs after transcoding.)

AAC

File extension: .m4a/.aac Stream: MPEG-4 AAC/MPEG-4, HE AAC (AAC Plus v1/2) Sampling Frequency: 32 kHz to 96 kHz

File names shown on the display

The display of this unit can only show single-byte letters and numbers. If the file information uses Japanese, Chinese or other double-byte characters, playback is possible but the name will not be shown correctly.

Precautions when using computers

FLAC

File extension: .flac Stream: FLAC Sampling Frequency: 8 kHz to 48 kHz Only 48 kHz is supported with USB.

MP3

File extension: .mp3 Stream: MPEG-1/2 Layer III Sampling Frequency: 8 to 48 kHz Bit Rate: 8 to 320 kbps/VBR

Ogg Vorbis

File extension: .ogg Stream: Ogg Sampling Frequency: 8 kHz to 48 kHz Bit Rate: 16 kbps to 128 kbps

and other devices to create files

p Always include the extension in the file name. p See the manual for the software that you are using

when you create a file using a PC.

Files that cannot be played correctly

p Files without extensions cannot be played. Even if the

file name has an extension, playback is not possible if the data format is incorrect.

p Variable bit rate files might not play back correctly. p When more than 2000 files are recorded on the USB

flash drive, the unit might not be able to play them correctly.

Connecting speakers (1)

Speakers

Precautions when making connections

p Complete all other connections before connecting

power plugs to power outlets.

p Read the owner’s manuals of all devices that will

be connected, and follow their instructions.

p Do not bundle connecting cables with power cords.

Doing so could cause noise.

SPEAKERS terminals

Connect speakers to this unit using commercially available speaker cables. This unit’s + (positive) terminals are red ( for the right speaker) and white (for the left speaker). speaker terminals are ^ (negative). Generally, the ¥ wire of the speaker cable is marked to make it distinguishable from the ^ wire of the cable. Connect the marked wires to the red and white ¥ terminals and the unmarked wires to the black ^ terminals.

p Check the impedance of your speakers. Connect

speakers with an impedance of 6 ohms or more.

Before connections

1. Remove about 1 cm (1/2”) of the sheath at the end of the speaker cable.

2. Twist the cable core well.

The black

ENGLISH

Making cable connections

1. Turn the terminal cap counterclockwise to loosen it.

2. Insert the wire into the hole in the terminal screw and turn the terminal cap clockwise to connect it securely.

RCA cable

LINE

CAUTION

Subwoofer

If the exposed end of a core wire in a speaker cable contacts another cable or terminal, a short could occur. Do not allow this to happen.

Connecting speakers (2)

Using an iPod/iPhone/iPad

Connecting speakers using banana plugs

You can also connect speakers using commercially available banana plugs. Connect the speaker cable to the banana plug first, and then insert the plug into the terminal.

p Carefully read the instructions of the banana plugs that

you intend to use with this unit.

p For North American customers

Before inserting banana plugs, remove the black cap from the top of each terminal cap.

For European customers

In accordance with European safety regulations, it is not possible to connect banana plugs into the speaker terminals on European models. The holes into which banana plugs are inserted have been covered with black caps. Connect the speakers using spades or bare wires. If the black caps become separated from the terminals, return them to their original position.

Compatible iPod/iPhone/iPad models

This unit can be connected to and used with the following iPod/iPhone/iPad models.

iPod nano ( 2nd, 3rd, 4th, 5th, and 6th generation) iPod touch (1st, 2nd, 3rd, and 4th generation) iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G iPad 2, iPad

p To connect an iPod/iPhone/iPad, use the USB cable sup-

plied with the iPod/iPhone/iPad.

SUBWOOFER OUT jack

You can connect a subwoofer to enhance low frequencies here. Connect a commercially available powered subwoofer to this u nit using a commercially available RCA cable.

p Use a subwoofer with a built-in amplifier. In

order to balance the levels with the main speakers, adjust the subwoofer volume while listening to audio that you know well. Adjust it as you like to suit the music.

1010

iPod/iPhone/iPad software

If the unit or remote control buttons do not work properly with your iPod/iPhone/iPad, updating its software might solve the problem. Download the latest software for your iPod/iPhone/iPad from the following Apple website.

http://www.apple.com/downloads/

Connections (1)

Power outlet

Personal computer

output device

CD recorder, etc.

Precautions when making connections

p Complete all other connections before connecting power plugs to power outlets. p Read the owner’s manuals of all devices that will be connected, and follow their instructions. p Do not bundle connecting cables with power cords. Doing so could cause noise.

Install the dedicated driver on the computer before connecting

(page 20)

Included power cord

USB cable

RCA coaxial digital cable

Optical digital cable

Audio cable

G H

ENGLISH

Audio cable

DIGITAL OUT

(COAXIAL)

Digital audio

DIGITAL OUT

(OPTICAL)

Digital audio

LRLR

LINE

OUT

Cassette deck/

Turntable

1111

Connections (2)

USB audio input port

Use to input digital audio from a computer. Connect with a USB port on the computer. Use a commercially available USB cable to make the connection.

p Install the dedicated driver before connecting the

computer to this port by USB (page 20).

ETHERNET port

If you want to use a wired Internet connection, connect the ETHERNET port of this unit to an Ethernet network using a commercially available Ethernet cable.

p If you connect or disconnect the Ethernet cable

while the unit is turned on, put the unit in standby, disconnect the power cord from the wall outlet, connect it and turn the unit on again.

Wireless LAN antenna

If you can use a wireless LAN in your installation site, the unit connects to the LAN using the wireless LAN antenna. As shown in the illustration on page 11, turn the antenna so that it points up.

Power inlet [~IN]

Connect the supplied power cord here.

p Unplug the cord from the outlet when not using

the unit for a long time.

V CAUTION

p Be sure to connect the power cord to an AC outlet

that supplies the correct voltage.

p Hold the power plug when plugging it into an outlet

or unplugging it. Never pull or yank on the power cord.

Digital audio input connectors [COAXIAL,

OPTICAL]

Use to input digital audio. Connect to the digital audio output connectors of a device capable of outputting digital audio.

COAXIAL: Coaxial digital cable (RCA) OPTICAL: Optical digital cable (TOS)

1212

AUX 1 IN/OUT jacks

White (L)

Red (R)

White (L)

Red (R)

These input/output analog audio signals. Connect this unit’s input and output jacks to the output and input jacks of other devices using commercially available audio cables.

p Connect an audio cable’s white pin plug to the

white (L) jack and connect its red pin plug to the red (R) jack.

PHONO jacks

Connect the turntable’s RCA pin cable to the PHONO jacks.

p Connect an audio cable’s white pin plug to the

white (L) jack and connect its red pin plug to the red (R) jack.

p Be sure to insert each plug securely. To prevent hum-

ming and interference, avoid bundling the signal interconnection cables together with the AC power cord or speaker cables.

ENGLISH

p If you want to use a recorder (eg. a cassette deck or

a CD recorder) with this unit, connect the output jacks of the recorder to the AUX 1 IN jacks of this unit and connect its input jacks to the AUX 1 OUT jacks.

p Be sure to insert each plug securely. To prevent hum-

ming and interference, avoid bundling the signal interconnection cables together with the AC power cord or speaker cables.

p This unit supports the use of MM cartridges (input

sensitivity: 2.5 mV/47 kΩ). It does not support the use of MC cartridges.

Grounding connector [SIGNAL GND]

Connect the grounding wire of the turntable here.

p This is not an electrical safety ground.

p If the grounding wire of the turntable is not con-

nected here, hum noise may be heard.

1313

Names and functions of parts (main unit) (1)

A B

MULTI JOG knob

Use this knob to set the clock and the timer. In USB/iPod mode, use this knob to scroll up and down the menu when an iPod/iPhone/iPad is connected. In USB/iPod mode, turn the MULTI JOG knob to search files inside folders or at the root level.

p When a USB flash drive is connected, turning this

knob skips between all the files (tracks) and folders within only the selected folder.

p In network mode, use for each file or setting mode. p Use this knob to adjust the low and high frequency

levels (bass and treble).

I J K

Remote sensor

When operating the remote control unit, point it towards the remote sensor.

Display

VOLUME knob

Use this knob to adjust the volume. Turn it clockwise to increase and counterclockwise to decrease the volume.

p After adjusting the volume, the volume level will

be retained even if you press the STANDBY/ON button to put the unit into standby.

NHG

1414

STANDBY/ON button

Press this button to turn the unit on or put it in standby mode. The color of the indicator above the STANDBY/ON button shows the status of the unit.

Indicator Status

Orange Standby

Blue ON

PHONES jack

To listen with headphones, first minimize the volume. Then, insert the headphones’ plug into the PHONES jack and gradually increase the volume. No sound will be output from the speakers while the headphones’ plug is inserted in the PHONES jack.

CAUTION Do not connect or disconnect headphones or turn the unit on or put it in standby while wearing them. Sudden loud noises could occur, which might cause hearing damage.

AUX 2 IN jack

Connect this jack to the headphones’ jack (or an audio output jack) of a portable audio player or other device using a commercially available 3.5 mm stereo mini plug cable.

SOURCE button

Use this button to select the source.

MENU button

In USB/iPod mode, use this button to go back to the previous menu when an iPod/iPhone/iPad is connected. When in network mode (Internet radio/media player), the setup menu appears.

Skip buttons [.//]

In USB/iPod mode, use these buttons to skip to the previous or next track or file when playing back or paused. Use these buttons to adjust the balance. When a menu is shown, use / to select in the same way as the ENTER button. When a folder is shown, press . to move up one folder level.

ENTER button

In USB/iPod mode, use this button to confirm selections in menus when an iPod/iPhone/iPad is connected. When making settings, use this button to confirm selection of a menu item. In network mode (Internet radio/media player), use to select a station or track.

ENGLISH

USB port

Connect an iPod/iPhone/iPad or USB flash drive.

1515

Names and functions of parts (MU) (2)

INFO button

While listening to the Internet radio or with the media player function, use this button to change the information on the display.

p For information about use in network mode, see

page 18.

Names and functions of parts (RC) (1)

Stop button [8]

In USB/iPod mode, use this button to stop playback. When “Media Player” is selected as the input source, hold this button for at least 2 seconds to stop playback.

NET button

Press when in network mode to switch between Internet radio and media player.

Play/pause button [7/9]

In USB/iPod mode, use this button to start or pause playback.

p For information about use in network mode, see

page 18.

1616

When both the main unit and the remote control have buttons with the same functions, this manual explains how to use either of them. The corresponding buttons can be used in the same manner.

STANDBY/ON button

Press this button to turn the unit on or put it in standby mode. The color of the indicator above the STANDBY/ON button shows the status of the unit.

TONE button

Use this button with the Scroll buttons (k/j) to adjust the low and high frequency levels as well as the left-right balance (page 26).

Indicator Status

Orange Standby

Blue ON

Source buttons [NET, USB/iPod, USB AUDIO,

COAXIAL, OPTICAL, PHONO, AUX 1/2]

Use these buttons to select a source.

NET............. Network mode (Internet radio/media

player)

USB/iPod.......USB/iPod mode

USB AUDIO ....USB audio input mode

COAXIAL .......Digital input mode (coaxial)

OPTICAL .......Digital input mode (optical)

PHONO.........Phono mode

AUX 1/2 ........External input mode (AUX)

p To select the media player, use the NET button. p Press the AUX 1/2 button again to switch between

AUX 1 and AUX 2.

REPEAT 1/ALL button

In USB/iPod mode, use this button to set the repeat playback of an iPod/iPhone/iPad or a USB flash drive (page 31).

SHUFFLE button

In USB/iPod mode, use this button to start shuffle playback of an iPod/iPhone/iPad or a USB flash drive.

Stop button [H]

In USB/iPod mode, use this button to stop playback of an iPod/iPhone/iPad or a USB flash drive. When “Media Player” is selected as the input source, hold this button for at least 2 seconds to stop playback.

Play/pause button [y/J]

In USB/iPod mode, use this button to start or pause playback of the iPod or USB.

p Refer to the table on the next page for operation in

network mode.

ENGLISH

TIMER button

Use this button to select the timer function (“Timer Daily”, “Timer Once”, or “Timer Off”).

SLEEP button

Use this button to set the sleep timer (page 50).

TIME SET button

Use this button to adjust the clock and to set the wake-up timer.

MENU button

In USB/iPod mode, use this button to go back to the previous menu. This button is equivalent to the MENU button on your iPod. When in network mode (Internet radio/media player), the setup menu appears.

ENTER button

In USB/iPod mode, use this button to confirm selections in menus when an iPod/iPhone/iPad is connected. When making settings, use for menu selection. In network mode (Internet radio or media player), use to select a station or track.

1717

Names and functions of parts (remote control) (2)

Skip button [.//]

DIMMER button

Use this button to change the brightness of the display (page 26).

INFO button

While listening to the Internet radio or with the media player function, use this button to change the information on the second line of the display.

DISPLAY button

In USB/iPod mode, use this button to change what information is displayed.

p When in network mode, the buttons on the unit and

the remote control function differently.

Main unit

Status Button Function Stopped Play/pause button

(7/9) Stop button (8)

Playing back Play/pause button

(7/9) Stop button (8)

Remote control

Status Button Function Stopped Play/pause button

(7/9) INFO button No function

Playing back Play/pause button

(7/9) Stop button (8)

INFO button Show information

Change network mode

No function Play/pause

Show information

Start playback

Play/pause

Stop playback

MUTE button

Use this button to mute the sound.

VOLUME buttons [+/−]

Use these buttons to adjust the volume level. Press + to increase and − to decrease the volume.

Scroll buttons [k/j]

In USB/iPod mode, use these buttons to select a folder or file that is on a device connected to the unit’s USB port. (When an iPod/iPhone/iPad is connected, use these to scroll through its menu.) When making settings, use these to scroll through menus. After pressing the TONE button, use to adjust the tone settings (low and high frequency levels) (page 26).

1818

Using the remote control unit

Precautions for use

V Misuse of batteries could cause them to rupture

or leak leading to fire, injury or the staining of items nearby. Please carefully read and observe the precautions on page 3.

p Point the remote control unit at the main unit’s remote

sensor from within 5 meters (16 feet) of it. Make sure that there are no obstructions between the remote control and the main unit.

p If direct sunlight or strong artificial illumination shines

on the remote sensor, the remote control might not function. If that is the case, move this unit to another location.

p If the remote control unit is operated near other devices

that generate infrared rays, or if other remote control devices using infrared rays are used near the unit, it might operate incorrectly. The other devices might also operate incorrectly.

Battery installation

Remove the cover from the back of the remote control and insert two AAA batteries with their ¥/^ ends oriented in the case as shown. Replace the cover.

ENGLISH

Battery replacement

If the operation range of the remote control decreases, the batteries have become exhausted. In this case, replace the batteries with new ones. For detailed information about the collection of batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.

1919

Playing back music on a computer (1)

Transmission mode

Installing the driver

In order for this unit to play back audio files stored on a computer, you must first install a driver on the computer. Please download this driver from the following web address.

Driver software download page

http://www.teac.co.jp/audio/software_teac_e.html

USB connection is only possible with computers running the following operating systems.

Windows XP (32-bit) Windows Vista (32/64-bit) Windows 7 (32/64-bit) Mac OS X 10.6 (Snow Leopard) (OS X 10.6.4 or later) Mac OS X 10.7 (Lion) Mac OS X 10.8 (Mountain Lion)

(As of October, 2012)

Operation with other operating systems is not guaranteed.

CAUTION

Install the driver before connecting the computer to this unit’s USB audio input port by USB.

If you connect this unit with a computer before installing the driver, it will not work properly. Moreover, if the computer is running Windows XP, its operation could become noticeably slower, requiring it to be restarted.

p Do not change the transmission mode during playback.

Doing so could cause the unit to freeze or other problems.

p Quit the music playback software on your computer

before changing the transmission mode.

Press the SOURCE button repeatedly to

select “USB Audio In”.

Press the NET button to select the mode.

Press once to show the current mode. Press again to change the mode.

p For instructions about driver installation procedures,

please see our download page.

p Depending on the combination of hardware and soft-

ware, proper operation might not be possible even with the above operating systems.

Transmission modes

You can choose from two transmission modes when connecting this unit’s USB audio input port to a computer by USB.

Transmittable sampling frequencies are 32 kHz, 44.1 kHz, 48 k Hz, 88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz.

2020

Example:

86%$XGLR,Q >0@

M1 mode

Use the settings to select M1. The unit connects with the computer using highspeed mode. When properly connected, you will be able to select “TEAC USB HS AUDIO” as an audio output from the computer OS.

M2 mode

Use the settings to select M2. The unit connects with the computer using highspeed asynchronous mode. When properly connected, you will be able to select “TEAC USB HS ASYNC AUDIO” as an audio output from the computer OS.

p In M2 mode, the audio data sent from the computer is

processed using this unit’s clock. By reducing the jitter during data transmission, this contributes to playback with better audio quality.

p When you connect this unit and a computer in M2

mode, if the playback sound should skip or noise should occur at fixed intervals, set the unit to M1 mode instead.

Playing back audio files on a computer

Connect a computer to this unit using a USB

cable.

USB cable

p Use a cable with a connector that matches that of

this unit.

ENGLISH

Turn the computer power on.

p Confirm that the operating system has started

properly.

Continued on the next page e

2121

Playing back music on a computer (2)

Press the POWER button to turn this unit on.

Press the SOURCE button repeatedly to

select “USB Audio In”.

Start playback of a music file on the computer.

Maximize the volume on the computer and use this unit’s VOLUME knob to adjust the output level for better sound quality. Minimize the volume on this unit before starting playback and gradually raise the level.

p You cannot control this unit from the computer, and

you cannot control the computer from this unit.

p Do not do any of the following when connected to a

computer and playing back an audio file. Doing so could cause the computer to malfunction. Always quit the music playback software before doing any of the following.

u Unplugging the USB cable u Putting the unit in standby u Changing the current input selection u Switching between transmission modes

p When connected to a computer and playing back an

audio file, computer operation sounds will also be output. If you do not want these sounds to be output, change settings on the computer to turn them off.

2222

p If you connect this unit with the computer or change its

input to “USB Audio In” after starting the music playback software, audio files might not play back correctly. If this should occur, restart the audio playback software or restart the computer.

p Do the following before starting the music playback

software. Doing them after could prevent proper music file playback. If this occurs, restart the music playback software or restart the computer.

• Connect the unit with the computer

• Set the unit input to “USB Audio In”

• Switch between M1 and M2 modes

Current Time

O

Sour

Status

Setting the current time (1)

Set the current time before using the unit.

p If the power cord is disconnected from the outlet, the

set time will be reset to the default.

Press the STANDBY/ON button to turn the

unit on.

The indicator above the STANDBY/ON button lights blue.

Press the TIME SET button.

p Press the TIME SET button repeatedly to cycle through

the following menu items. The items other than Current Time are used to set the alarm clock (page 50).

Time

ce Select

p For Europe, the unit uses the 24-hour “military” clock.

For North America, the unit uses the 12-hour clock.

p Press the stop button (H) to cancel the time setting.

p When no action is taken for 30 seconds, the clock

setting mode will be cancelled.

Press the scroll buttons (k/j) to set the

current hour and press the ENTER button.

ENGLISH

“Current Time” appears and the hour value blinks.

The “minute” value blinks.

p You can also use the MULTI JOG knob and ENTER

button on the main unit in the same way.

Continued on the next page e

2323

Setting the current time (2)

Basic operation (1)

Press the scroll buttons (k/j) to set the

current minute and press the ENTER button.

The clock will start from the set minute at 0 seconds.

Checking the current time

When the source is set to Audio In, AUX 1/2, COAXIAL, OPTICAL or PHONO, press and hold the INFO button for at least three seconds to show the current time for five seconds.

In this section, we explain operations that are the same in every mode.

Press the STANDBY/ON button to turn the

unit on.

The indicator above the STANDBY/ON button lights blue.

2424

Press the SOURCE button to select the

Internet Radio/wUSB/iPodwUSB Audio In

AUX2sAUX1sPHONOsOPTICALsCOAXIAL

source.

Every time you press the SOURCE button, the source changes as follows:

MediaPlayer

Turn the VOLUME knob counterclockwise to

decrease the volume.

VOLUME MIN: Minimum volume

VOLUME MAX: Maximum volume

ENGLISH

NET............. Network mode (Internet radio/media

player)

USB/iPod.......USB/iPod mode

USB Audio In...USB audio input mode

COAXIAL .......Digital input mode (coaxial)

OPTICAL .......Digital input mode (optical)

PHONO.........Phono mode

AUX 1/2 ........External input mode (AUX)

p To select the media player, use the NET button. p Press the AUX 1/2 button again to switch between

AUX 1 and AUX 2.

Start playback on the source and use the

VOLUME knob to adjust the volume to its optimal level.

VOLUME MIN: Minimum volume

VOLUME MAX: Maximum volume

p In order to prevent sudden loud noises, raise the vol-

ume gradually.

p When connecting the headphone jack of a portable

audio player to this unit, you must raise the player’s headphone output volume level.

Continued on the next page e

2525

Basic operation (2)

BASS TREBLE

p If you raise the volume level of the connected device

too high, the sound might distort. If this occurs, lower the volume of the connected device until distortion stops and then adjust the volume on this unit.

Muting the output

To mute the sound temporarily, press the MUTE button. Press the MUTE button again or change the volume setting to restore the sound.

Adjusting the tone and balance

You can adjust the low and high frequency levels as well as the left-right balance as you like.

Press the TONE button repeatedly to select

BASS, TREBLE, or BALANCE.

Every time you press the TONE button, the mode changes as follows.

BALANCE

Dimmer

Press the DIMMER button to switch between the two brightness settings: bright and dim.

p The dimmer setting is turned off when you press the

STANDBY/ON button.

2626

Within 3 seconds, press the scroll buttons

(k/j) to adjust the bass or treble, or press the skip buttons (.//) to adjust the balance.

p The low (BASS) and high (TREBLE) frequency set-

tings can each be adjusted in a range between –5 and +5. The left-right balance can be set to CENTER or from +1 to +6 L/R (left/right).

p You can also use the main unit’s MULTI JOG knob

to adjust the low and high frequency levels (bass and treble).

About the ErP

Listening files on a USB flash drive (1)

This product is compliant with the European ErP Standby Power Regulation. In order to comply with this regulation, the automatic power saving function of this unit is set to 30 minutes when shipped new, so the unit will automatically enter standby if 30 minutes pass under the conditions shown in the following table. However, when “On” is selected for the network standby setting (page 37), this function is not active. (The default network standby setting is “Off”.)

p When you turn on the unit, the selected source is the

one selected before the unit was put into standby.

p During playback in iPod mode, if you put the unit into

standby by pressing the STANDBY/ON button, the next time the power is turned on again, the unit will be in iPod mode and playback will start automatically when an iPod/iPhone/iPad is connected. Playback will not start automatically in other modes.

Status AirPlay,

iPod/ iPhone/ iPad

No connection

Stopped/ paused

No input signal

USB flash drive

   

*  

- - -

Media player Internet

External input



You can play audio files stored on a USB flash drive by connecting it to this unit. For details on playable files, see page 8.

Press the SOURCE button repeatedly to

select “USB/iPod”.

p You can also use the USB/iPod button to select this

directly.

p “Not Connected” will be displayed if no USB flash

drive is connected.

Connect a USB flash drive to the unit.

ENGLISH

External input: USB Audio In, COAXIAL, OPTICAL, PHONO,

AUX 1/2

 Automatic power saving function active

- Automatic power saving function not active * Compatible only with AirPlay / Not applicable

Select the file you want to play.

For details, see page 29.

Press the play/pause button (y/9) or

ENTER button to start playback.

p If you press the / button when a file is

displayed, playback will also start.

2727

Listening files on a USB flash drive (2)

Stopping playback

Press the stop button (H) to stop playback.

Pausing playback

Skipping to the next or previous track/file

During playback, press the skip buttons (. //) repeatedly until the desired track/file is found. The selected track/file will be played from the beginning.

p When the .button is pressed during playback, the

track/file being played will be played from the beginning. To return to the beginning of the previous track/ file, press the .button again.

Press the play/pause button (y/J) to pause playback at the current position. To resume playback, press the play/pause button (y/J) again.

p When the playback time is five seconds or less, press

. to play the previous track.

p When playing tracks on a USB flash drive, skipping to

the next track from the last track will stop playback.

2828

Searching inside folders

You can search for and select tracks by name within folders on a USB flash drive and play them back. If double-byte characters, such as Japanese kana, are used in a file name, this unit cannot show them correctly, so accurate searching will not be possible.

Press the scroll buttons (k/j) to select the

folder you want to listen to the track within.

Press the ENTER button.

Playback starts from the selected track.

p When playing files on a USB flash drive, press the

skip (.) button to move to the folder before.

p When viewing a folder, press the skip (/) button

to move to the next folder.

p When a file is selected, press the skip (/|) button

to start playback of the track.

ENGLISH

p MP3/WMA files that are not inside folders will be

shown after the folders in order.

Press the scroll buttons (k/j) to select the

track you want to listen to.

2929

Playback time (normal)

Artist

Album

Information shown on the display

During playback of a file on a USB flash drive, information about the track scrolls on the display. During playback, press the DISPLAY button repeatedly to change what is shown on the display.

Shuffle playback

Press the SHUFFLE button to activate shuffle playback mode. Tracks on the USB flash drive will be played in random order.

USB flash drive

Example:

itle

p The display of this unit can only show single-byte letters

and numbers. If the file information uses Japanese, Chinese or other double-byte characters, playback is possible but the name will not be shown correctly.

p A maximum of 80 characters of track information can

be shown.

86%6KXIIOH :0$

p If you press the skip button (/) during shuffle play-

back, the next track/file will be randomly selected and played. If you press the skip button (.), the currently played track/file will be played from the beginning. During shuffle playback, playback will not return to a track that has already completed playing.

p To cancel shuffle playback, press the SHUFFLE button.

p If you press the stop button (H), shuffle playback will

stop, but shuffle mode will remain active.

p Shuffle playback of a USB flash drive will play all the

files in the selected folder only.

3030

+ 146 hidden pages