TCL L40D2700B Schematic

TCL
SERVICE MANUAL
L40D2700B/MS08BP
1. Caution…………………………………………………………………………
2. specification……………………………………………………………………
3. Alignment Procedure………………………………………………………… 4Block diagram………………………………………………………………… 5Scheme Diagram ……………………………………………………………
6. Troubleshooting………………………………………………………………
([SORGHGUDZLQJ
This m anual i s t he l atest at t he t ime of pr inting, and doe s not include the modification which may be made after the printing, by the constant improvement of product
RISK OF
ELECTRIC
SHOCK DO
NOT
OPEN.
SCHNEIDER ELECTRONICS GMBH-GERMANY
1. CAUTION
CAUTION:
Use of controls, adjustments or procedures other than those specified herein may result in hazardous radiation exposure.
CA UTION : TO RE DUCE THE RIS K OF
CA U T IO N
RISK
SHOCK
The lighting flash with arrowhead symbol, with an equilateral triangle is intended to alert the user to the presence of uninsulated voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to the person.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
ELECTRI
NOT
OPEN.
ELECTR ICAL SH OCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PAR TS INS IDE . RE FER SER VIC ING TO QUALIFIE D SERVIC E PERS ONNEL.
dangerous
WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
2
2
SCHNEIDER ELECTRONICS GMBH-GERMANY
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
Read all of these instructions. Sa ve these instructions for later use . Follo w all Warnings and Instructions marked on the audio equipment.
1. Read Instructions-All the safety and operating instructionsshouldbe read before the productis operated.
2. Retain Instructions- The safety and operating instructions should be retained for future reference.
3. Heed Warnings- All warnings on the product and in the operating instructions should be adhered to.
4. Follow Instructions- All operating and use instructions should be followed.
FOR YOUR PERSONAL SAFETY
1. When the power cord or plugis damaged or frayed, unplug this television set from the wall outlet and refer servicing to qualified service personnel.
2. Do not overload wall outlets and extension cords as this can result in fire or electric shock.
3. Do not allow anything to rest on or roll over the power cord, and do not place the TV where power cord is subject to traffic or abuse. This may result in a shock or fire hazard.
4. Do not attempt to service this television set yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
5. Never push objects of any kind into this television set through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the television set.
6. If the television set has been dropped or the cabinet has been damaged, unplug this television set from the wall outlet and refer servicing to qualified service personnel.
7. If liquid has been spilled into the television set, unplug this television set from the wall outlet and refer ser vicing to qualified service personnel.
8. Do not subject your television set to impact of any kind. Be particularly careful not to damage the picture tube surface.
9. Unplug this television set from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
10.1. Do not place this television set on an unstable cart, stand, or table. The television set may fall, causing serious injury to a child or an adult, and serious damage to the appliance. Use only with a car t or stand recommended by the manufacturer, or sold with the television set. Wall or shelf mounting should follow the manufacturer s instructions, and should use a mounting kit approved by the manufacturer.
10.2. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
3
3
SCHNEIDER ELECTRONICS GMBH-GERMANY
PROTECTION AND LOCATION OF YOUR SET
11. Do not use this television set near water ... for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. Never expose the set to rain or water. If the set has been exposed to rain or water, unplug the set from the wall outlet and refer servicing to qualified service personnel.
12. Choose a place where light (artificial or sunlight) does not shine directly on the screen.
13. Avoid dusty places, since piling up of dust inside TV chassis may cause failure of the set when high humidity persists.
14. The set has slots, or openings in the cabinet for ventilation purposes, to provide reliable operation of the receiver, to
protect it from overheating. These openings must not be blocked or covered.
Never cover the slots or openings with cloth or other material. Never block the bottom ventilation slots of the set by placing it on a bed, sofa, rug, etc. Never place the set near or over a radiator or heat register. Never place the set in enclosure, unless proper ventilation is provided.
a built-in
PROTECTION AND LOCATION OF YOUR SET
15.1. If an outside antenna is connected to the television set, be sure the antenna system is grounded so as to provide some
protection against voltage surges and built up static charges, Section 810 of the National Electrical Code, NFPA No. 70-1975, provides information with respect to proper grounding of the mast and supportingstructure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrode, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE INSTRUCTIONS
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA LEAD- IN WIRE
GROUND CLAMP
ELECTRIC SERVICE
EQUIPMENT
NEC-NATIONAL ELECTRICAL CODE
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
GROUNDING CONDUCTORS (NECSECTION 810-21)
GROUND CLAMPS
POWER SER VICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H)
15.2. Note to CATV system installer : (Only for the television set with CATV reception)
This reminder is provided to call the CATV system attention to Ar ticle 820-40 of the NEC that provides
installer s guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entr y as practical.
16. An outside antenna system should not be located in the vicinity of overhead power lines or other electric lights or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
17. For added protection for this television set during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage due to lightning and power-line surges.
4
4
SCHNEIDER ELECTRONICS GMBH-GERMANY
OPERATION OF YOUR SET
18.
This television set should be operated only from the type of power source indicated on the marking label.If you are not sure of the type of power supply at your home, consult your television dealer or local power company. For television sets designed to operate from battery power, refer to the operating instructions.
19. If the television set does not operate normally by following the operating instructions, unplug this television set from the wall outlet and refer servicingto qualifiedservice personnel. Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the television set to normal operation.
20. When going on a holiday : If your television set is to remain unused for a period of time, for instance, when you go on a holiday, turn the television set and unplug the television set from the wall outlet.
off
IF THE SET DOES NOT OPERATE PROPERLY
21. If you are unable to restorenormal operation by followingthe detailedprocedurein your operatinginstructions, do not attempt any further adjustment. Unplug the set and call your dealer or service technician.
22. Whenever the television set is damaged or fails, or a distinct change in performance indicates a need for service, unplug the set and have it checked by a professional service technician.
23. It is normal for some TV sets to make occasional snapping or popping sounds, particularly when being turned on or off. If the snapping or popping is continuous or frequent, unplug the set and consult your dealer or service technician.
FOR SERVICE AND MODIFICATION
24. Do not use attachments not recommendedby the television set manufacturer as they may cause hazards.
25. When replacement parts are required,be sure the service technicianhas used replacementparts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
26. Upon completion of any service or repairs to the television set, ask the service technician to perform routine safety checks to determine that the television is in safe operating condition.
5
5
Product Type
LCD Smart TV
Music
support MP3/AC3/HE-AAC/LPCM/WMA
Chassis
Picture
Support JPEGBMPPNGMPO
CPU 1GHZ
Support H.264MPEG1MPEG2
GPU ---
DIVXMotion JPEG/VC1
OS Linux
Memory Bein 2Gb DDR3 + 4Gb NandFlash File ---
OSD Language
English/Portuguese/Spanish/Vietnam/French/ Russian/Thai/Arabian/Persian/Mongolian
PAL/SECAM B/G,D/K,I ;NTSC-M
DVB-T/DVB-T2/DVB-C
AV System
PAL,NTSC
DVI Video Format
Up to XGA for HDMI-PC
Channels(Analog)
199(1~199)
HDMI Video Format up to 1080P
DTV Channels DVB-T2
1000(1~1000)(programs)
PC Compatibility Up to SXGA
Power Supply
AC 110V-240V 50/60Hz
Power ConsumptionTV On
65W
Power ConsumptionStandby
0.5W
Backlight Unit
LED
Certification
CB
Panel supplier CMO(V400HJ6-PE1)
Energy Efficiency Level
--- Aspect Ratio 16:9
Wired Network Default Panel Size (inch) 40"
Built-in Wi-Fi Network Display Resolution 1920*1080
Brightness (cd/m2)(typ.) 280
Contrast Ratio 4000:1
Response Time (G to G) 8.5ms
EPG Yes(at DTV) Viewing Angle (H/V) 176°/176°
Subtitle Yes(at DTV) Life Time(Typ.)
30,000hrs
Parental Control Yes(at DTV) Color 16.7M (8 bit)
Lock Yes Refresh Rate 60Hz
V-Chip ---
CCD (Closed Caption) ---
Sleep Timer Yes
Teletext Yes
Nicam Yes
Side
MTS ---
Screen Saver Yes
System Update Yes
Hotel Mode Optional(In factory mode)
REC
Yes
Analog / Digital Signal Receiver Yes
MHL
---
Card Reader No
TimeShift Yes
Off Timers Yes
Natura Light Technology ---
DCC(Dynamic Contrast Control) ON/OFF
Backlight Adjustable Yes (0~100)
Color Temperature
Warm / Normal/ Cool
Picture Mode
Normal, Mid, Vivid, User
Picture Size
Auto,16:9,4:3,Just Scan
Gamma Adjustable ---
Comb Filter 3D
Dynamic Noise Reduction 3D
Adaptive Deinterlacing 3D
Motion Compensation Yes
Sound
Speakers Integrated speakers (Bottom Side)
Audio Power OutputTHD=7% 2×8W
Smart Volume Yes(Built-in)
Smart Audio Normal,Music,Movie,News,User
Sound Control
Volume, Balance,5 Band EQ
Sound Scene ---
Down
Surround Sound Yes
DD (Dolby Digital )
Yes
Dobly DD+ Yes
Basic Function
Picture
Terminals
Special Function
PRODUCT SPECIFICATION RELEASE
Model: L40D2700B/MS08BP
Version2.0 Issued On: 2015-3-10
Internet Link
Signal Format Capability
Panel Specification
Video
Basic Information
Media Code
TV System
1
2
3
4
MS08BP-AP
Twitter Social Network GoLive TV
it can display Golive icon and play programs
Facebook Social Network
from all countries.
Web Browser QJY •Browser
YouTube V4 YouTube Leanback
File Share Powered by DLNA or W i-Fi Network
Wireless Di splay Wireless Di splay
picasa
Online Album open API
GoLive TV
File Share
By connecting the TV and a device
(computer, smart, phone, pad, etc.)
to the same local network, you can enjoy
the music, videos and pictures shared
by the device on the TV.
Mechanical Key Specification
Carton Dimensions LxWxHmm
1120*144*655
Container Loading---20 feet pcs
280
Container Loading---40 feet pcs
592
Container Loading--40 feet Hi ghpcs
680
Net Weight W ith StandKg
7.1
Net Weight W ithout StandKg
6.9
Gross Weight W ith PackagingKg
9.3
VESA Mounting Dimensions LxHmm
100x150
Operation Manual English(Default) Wall Mount
WMB331
Remote Control and batteries RC200(with two batteries)
Wireless Keyboard ---
Base Stand
Integrated Packaging
Wireless Mouse ---
AC power cord 1 pc
Game Controller ---
Adapt Cable Wire For AV
1 pc
Drafted by: gongjunzan Approved by:
Design and specifications are subject to change without notice!
Mechanical ID Picture
Pre-Installed Application List
Special Function
Wireless di splay technology can realize the notebook with the TV set, projector display terminal wireless connection, not a machine connecting line.Put the notebook display content, such as video, games, pictures, play wireless transmission to the TV
Optional Accessories
Essential AccessoriesDefault
Remote ID Picture
Unit: mm
81.3MM
197.8MM
563MM
521.1MM
15.5MM
15.5MM
18.5MM
911MM
810.9MM
第 1 页共 11 页
TCL 集团多媒体电子全球制造中心 GP 设计中心
文件编号:IPC/SJ/FK02-2013 序号:
Alignment Procedure
MS08BP/MS08BPA Series
MODEL:L40B2800/L32D2700/L40D2700
VERSIONV1.0
PREPARED BY : Gongjunzan DATE : 2015-2-10
APPROVED BY : DATE :
第 2 页共 11 页
History Description of major changes Release
Changed by
Date
V1.0 2015-2-10
1.Overview
MS08BP These chassis are designed for Eastern Europe markets Ready for IPTV. The main
chip is from Mstar and supports below features matrix:
2.Factory Menu
1、Methods of Entering
Method 1:Using the remote ,
Select “Picture” and press “OK” key to enter into Picture Mode press RIGHT” or “LEFT” key Select User Mode
- Scroll down to "Contrast" item
- Press the subsequence RCU keys “9”, “7”, “3” and “5”will appear in the left top of screen In case of “Factory hotKey” is enabled(On), just press RCU “Return” key to pop-up
again the Factory menu.
The status of “Factory Key” can be changed in Factory Menu->Hotkey. Press RCU “OK” key to enter the submenu. Press RCU “Menu” key to go back to the root menu. Press RCU “RIGHT” or “LEFT” key to change the values. Press RCU “OK” key run the function. Press RCU “Exit” key exit the Factory menu.
第 3 页共 11 页
2. General introduction
FACTORY MENU
ITEMS
1-Factory hotkey Off
Default Setting
Description
Factory hotkey Switch (OFF/ON).Should be OFF after factory alignment
OFF:The set would enter standby mode after 15 minutes without input signal;
ON:Aging mode. Aging time will display on the left bottom of screen.
2-WARM-UP Off
NOTE: Enter and exit the aging mode method: 1, press on the remote control Left and right the cursor keys will Factory hotkey set to ON; 2, WARM UP is set to ON; according to the panel on the "menu" button to exit the aging mode
3-ADC ADC calibration(refer as follow),NOTE: Not
adjust
St at us
OK
OK
OK
4-White balance White Balance data adjustment ( refer as
follow)
The balance data is set by PE before the mass production. Do not need adjust.
5-SHOP init(Option)
DO Reset the set after production
alignment;(This operation will remove all unnecessary factory value; The factory hotkey will be turn off)
6-NVM reset DO System initialization. Restore all data
except the White Balance and ADC data ;Only for R&D.
7-Preset Factory Channel
DO/HZ Preset specific factory channels for
specific factory. Press left and right button to select the factory, and then press OK to confirm.
8-Power on mode LAST On: Always turns on TV when AC power on
STB:Always goes to standby mode when AC power on
OK
OK
OK
OK
OK
LAST:Restore the status before the last AC power off
第 4 页共 11 页
t
d
9-USB UPDATE(option)
USB update,(refer as follow)
Sub-item Value No
Main Upgrade
MEMC Upgrade
HDCP Uprade
Mboot upgrade
CI KEY Upgrade
NVM Upgrade
NVM backup
CH list Upgrade
CH list backup
NetflixESN Upgrade
MAC Upgrade
Upgrade software Upgrade MEMC Upgrade HDCP Upgrade Mboot Upgrade CI KEY Upgrade NVM Backup NVM Upgrade CH list Backup CH list Upgrade ESN Upgrade MAC Ad
10—Deviceld test This item only factory used,
Note: Below the factory menu, some model information are showed, including
software version, Project Name, SIACP Version, and SW release time.
OK j
3)ADC Submenu:
NOTE: ADC Date use Default Setting, do without adjust
4)WHITE BALANCE Submenu
ITEMS Default
Setting
Source Current
Source
Description Statu
s
Current Source( HDMI1 need adjustment, Other
OK
Source not use)
COLOR TEMP NORMAL Medium/Cool/Ware OK
R gain 128 R-GAIN OK
G gain 128 G-GAIN OK
B gain 128 B-GAIN OK
White
DO ONLY FOR TCL R&D OK Balance init
NOTE:The first step is to adjust HDMI1
第 5 页共 11 页
3.Design Menu
1、Methods of Entering:
Method 1:Using the remote, enter the “Picture” submenu in the OSD; choosing
the “contrast” item and press the 1,9,5,and 0 in series ,Design Menu will appear in the left top of screen.
Method 2: Press RETURN button when DESIGN HOTKEY is enabled (ON).
2、General introduction
DESIGN MENU
ITEMS Default
Setting
DESIGN HOTKEY
1-FACTORY MENU
2-SHOP Setting
3-Other Setting
4-SERVICE menu
5-PARAM SETTING
OFF ON/OFF OK
ON/OFF OK
Default setting submenu after production
Other set .Only for TCL R&D OK
After service menu description OK
Parameter setting submenu OK
Description Status
OK
alignment refer to **
6-HOTEL MENU
SHOP INIT submenu
ITEMS Default
Setting
Volume 30 0-100 adjustable OK
PIC MODE STANDARD Normal/Vivid/Mild/User OK
SOUND MODE STEREO Movie/news/Normal/Music/User OK
OSD Language
Preset CH 1 0-199 adjustable OK
English Up to 10 languages optional OK
Hotel submenu(not
Description Status
adjust)
OK
第 6 页共 11 页
Color Temp Normal Normal/warm/cool
Sale Mode Home Mode
COLOR SYS AUTO AUTO、PAL、 SECAM OK
SOUND SYS DK DK、BG、I、M OK
Other Setting
ITEMS Default
Setting
QMAP AUJUST
NVM Reset
Off
Do
ALL
Got User ID
Use Test
Off
Off
Host
Hidev
SSCOM Debug
DTV
Off
on
Off
Description Status
White/Red/Green/Blue/Black/Yellow/Gray/Pink(not
adjust)
Wait(not adjust)
On/Off(not adjust)
On/Off(not adjust)
Off..1\2\3(not adjust)
On/Off(not adjust)
On/Off(not adjust)
OK
OK
OK
OK
OK
OK
OK
Reset Shop
BGM
WSS&ATF
Do
On
On
PARAM SETTING
Picture Curve
ITEMS Default
Setting Brightness Curve Contrast Curve Color Curve
Hue Curve
Sharpness Curve
Wait(not
adjust)
On/Off(not adjust)
On/Off(not adjust)
OK
OK
Description Status
Brightness curve. Exclusively used by R&D
Contrast curve. Exclusively used by R&D
Color curve. Exclusively used by R&D
Hue curve. Exclusively used by R&D
Sharpness curve. Exclusively used by R&D
OK
OK
OK
OK
OK
第 7 页共 11 页
Tint Curve
BackLight Curve OverScan
Sound Curve
Volume Curve
SSC adjust
SSC
>>>
Overscan Adjust
Over Scan
DBC
Tint Curve. Exclusively used by R&D
BackLight curve. Exclusively used by R&D
Exclusively used by R&D
Volume curve. Exclusively used by R&D
SSC adjust . Exclusively used by R&D
Over Scan Exclusively used by R&D
OK
OK
DBC
Back Light Curce
Back Curve
Audio amp Setting
Audio
amp
Setting
DTV Para Setting
DTV Para
DBC Exclusively used by R&D
Back curve. Exclusively used by R&D
Audio amp Setting
. Exclusively used by R&D
DTV Para Setting
OK
OK
OK
Setting
Hotel menu
. Exclusively used by R&D
第 8 页共 11 页
4、Service Menu
1、Methods of Entering
Using the remote, enter the “Picture” submenu in the OSD; choosing the “contrast” item and press the 9,7,0 and 5 in series, Service Menu will appear in the left top of screen
SERVICE MENU:
ITEM Defau
Description Status lt Setti ng
1-Factory hotkey Off
Factory hotkey Switch (OFF/ON).Should be OFF
after factory alignment
OFF:The set would enter standby mode after 15
minutes without input signal;
ON:Aging mode. Aging time will display on the
left bottom of screen.
2-WARM-UP Off
NOTE: Enter and exit the aging mode method: 1, press
on the remote control Left and right the cursor keys will
Factory hotkey set to ON; 2, WARM UP is set to ON;
according to the panel on the "menu" button to exit the
aging mode
3-ADC ADC calibration(refer as follow),NOTE: Not
adjust
OK
OK
OK
4-White balance White Balance data adjustment(refer as follow)
The balance data is set by PE before the mass
production. Do not need adjust.
5-SHOP init(Option)
DO Reset the set after production alignment;(This
operation will remove all unnecessary factory
value; The factory hotkey will be turn off)
6-NVM reset DO System initialization. Restore all data except
the White Balance and ADC data ;Only for R&D.
7-Preset Factory Channel
DO/HZ Preset specific factory channels for specific
factory. Press left and right button to select
the factory, and then press OK to confirm.
8-Power on mode LAST On: Always turns on TV when AC power on
STB:Always goes to standby mode when AC power
on
LAST:Restore the status before the last AC
power off
OK
OK
OK
NG
OK
第 9 页共 11 页
e
e
9-USB UPDATE(option)
USB update,(refer as follow)
Sub-item Value Not
Main Upgrade
MEMC Upgrade
HDCP Uprade
Mboot upgrade
CI KEY Upgrate
NVM Upgrade
NVM backup
CH list Upgrade
CH list backup
NetflixESN Upgrade
MAC Upgrade
Upgrade software Upgrade MEMC Upgrade HDCP Upgrade Mboot Upgrade CI KEY Upgrade NVM Backup NVM Upgrade CH list Backup CH list Upgrade ESN Upgrade MAC Addr
10—Deviceld test This item only factory used, ok
5. Debugging
5.1. General Steps of debugging
According to the requirement of the order, below steps are needed for
appropriate setting.
1) Enter the Factory Menu, enable FAC HOTKEY.
2) Check Project ID and the version of software, release date displayed
at the bottom of Factory Menu.
3) Enter Design Menu, choose SERVICE MENU->Project ID, choose
corresponding Project ID number of the product (Refer to the “V6-PROJECT -ID0**”in the BOM list).
4) Return to Factory Menu, check the Product model.
5) Choose Factory Menu->NVM RESET and press the right button of the
remote and wait until prompt OK appears.
6) Restart the set
7) According to the requirement of the order, Set the items of SHOP
INIT and Hotel Menu etc.
8) After aging under normal temperature, calibrate ADC and adjust
white balance.
9) Choose Factory Menu ->SHOP and press the button of remote to
initialize the set.
Note: After step 9, Hotel Menu will be disabled by default. Therefore,
第 10 页共 11 页
if the order requires hotel function, it is necessary to enable hotel function by set Design MENU->Service Menu->HOTEL ENABLE to ON.
5.2. Equipments
·Color Analyzer CA-210.
·Video Pattern Generator Chroma2329.
·Color TV Pattern Generator PM5418/Fluke5418.
·VGA cable , AV(RCA) cable , HDMI cable etc.
5.3. ADC Function not Calibration
5.4. White Balance adjustments (Manual)
Before adjustment ,you must make sure the ADC status(only PC and YPbPr) is “success”and Color Analyzer has been calibrated .Only AV1,YPbPr,PC,HDMI1 need to be adjusted. HDMI1 should be the first.
5.4.1. Signal and generator
The pattern of the signal should be used are White (Chroma2329 pattern
113) and Grey (pattern 114).
The format of signal are respectively 720P for HDMI1 (Chroma2329 Timing 69),PAL (Chroma2329 Timing38) for AV1,1024X768@60Hz(Chroma2329 Timing14) for VGA 。
5.4.2. Steps of adjustment
1).Enter the factory menu-> White Balance, select source HDMI 1 and
Normal Temperature.
2).Input grey signal in 720p format.
3).Change R-OFFSET and B-OFFSET to make sure the value of color
coordination equal to (X=0.270 +/-0.015;Y=0.290 +/-0.015).
4).Input white signal in 720p format.
5). Change R-GAIN and B-GAIN to make sure the value of color
coordination equal to (X=0.270 +/-0.015;Y=0.290 +/-0.015).
6).Repeat step 2—5 until both of the value of color coordination of
white and grey equal to (X=0.270 +/-0.015;Y=0.290 +/-0.015).
After the adjustment of HDMI1, you can switch to other source AV, PC and YPbPr and repeat step 1—6 to do the WB adjustment.
第 11 页共 11 页
Note: For some small size LED panel,the color coordination of specifications is not X=0.280/Y=0.290,and we recommend you adopt the values from panel specifications.
5.5. ADC Calibration and White Balance Adjustment (automatic)
The process of adjusting White Balance automatically is out of the range of this file, Please refer to the relevant technical file of HuiZhou factory of TCL.
6.Chip list of software programming before SMT
Following chips must be programmed before SMT by tools
Position Chip type Software description
Chassis
Name
U301 MT29F2G08ABAEA HDMI HDCP Key, System Software etc. MS08BP
U301 MT29F4G08ABAEA HDMI HDCP Key, System Software etc. MS08BPA
7.Software update
Method of SW update:
1) Download the bin file to the root directory of your USB device (Do
not change the file name); Then insert the USB device to USB interface of TV set.
MS08BP/MS08BPA Series with its upgrade file corresponding relation as thetable below show:
Chassis Name
Sales area
Upgrade filename Remark
MS08BP RU MS08BPupgrade.bin DVB-T2
MS08BPA AP MS08BPupgrade.bin DVB-T2
2Appendix n “How to upgrade SW FLASH using Mstar tool”
See Appendix o “How to upgrade MBOOT using USB”
¾ Copy the SW BIN image “ Note: If there’s already other “ renamed.
¾ Plug USB stick to the TV USB slot.
¾ Press RCU MENUÆOptionÆ Software upgradeÆBy USBÆConfirm.
Or, turn off the TV press and hold the power key of key board before reconnect AC cord to restart TV for 5-8seconds (Forced Upgrade).
MstarUpgrade.bin” into USB stick root path.
MstarUpgrade.bin” into USB root, it needs to be deleted or
第 12 页共 11 页
¾ When the "UPGRADING SOFTWARE" picture appears as below, it means TV is
uploading SW BIN image. Waiting a few minutes.
¾ When updating is successful, TV should restart automatically.
Appendix p “How to upgrade FLASH SW using USB”
There are two methods to upgrade SW using USB, the first one like below
¾ In the previous of upgrade SW using USB, should program mboot bin file
V8-xMS08BP-LB1Vxxx.bin” by ISP_Tool or by USB. .
¾ Then switch off TV by removing AC cord. ¾ Copy the SW BIN image “MS08BPupgrade.bin” for MS08BP/MS08BPA into
USB stick (pen drive) root path
Note: If there’s already other The same name
into USB root, it needs to be deleted or renamed
¾ Plug USB stick to the TV ¾ Press and hold the power key of key board before reconnect AC cord to restart
TV for 5-8seconds.
¾ Once USB stick starts blinking, TV is uploading SW BIN image. ¾ When update is successful, TV should restart automatically. ¾ Remember to perform “Factory menuÆNVM reset“ and then press RCU “OK
key
¾ Switch off TV by removing AC cord ¾ Reconnect AC cord to restart TV and wait few seconds for Eeprom update
The second method
¾ To use this method, there should be SW in mainboard to ensure TV can display
normally.
¾ Copy the SW BIN image “V8-XMS08BP-LF1VXXX.bin” into USB stick (pen
drive) root path
¾ Press RCU MENUÆSettingÆFunctionÆsoftware upgradeÆOKÆBy USB ¾ TV display warning information, that means it is upgrading, almost 3minutes later,
when upgrade successful, TV should restart automatically.
第 13 页共 11 页
Appendix q “How to change ProjectID with RCU”
¾ Process following subsequence IR codes to change project ID:
062598+MENU+xxx (xxx: Project ID, ex: 001)
¾ Restart TV
Appendix r “How to upgrade MAC Address
¾ Upgrading MAC address need to use the tool in factory and through serial
command, the specific methods according to the operation of the factory guidance.
Appendix s “Instructions of Updating SW”
1. The following IC should be pre-copied before SMT process
Position PART TYPE Part Number SW
Chassis Name
U301
CPP
U301
CPP
IC-TSOP48 13-FS29F2-G0B Mboot, Main Software MS08BP
IC-TSOP48 13-FHMT29-4GB Mboot, Main Software MS08BPA
2. The MAC Address, HDCP KEY, Device ID must be upgrade by debug port
into U301.
8, Project ID selecting
1) Press the Menu button of remote control, then select Contrast item
of Picture submenu; press 1,9,5,0 consecutively, there you go the Design Menu.
2) Select the SERVICE MENU item, press OK button of the remote to enter
submenu,
3) Select the PROJECT ID item, press OK button of the remote to enter
the submenu;
4) Press the right or left button of the remote to select the ID you want;
5) After ID selection, press MENU button of the remote to exit DESIGN
MENU.
6) Finally, do AC power on/off.
Signal of MS08BP/BPA/MS08GP Block Diagram
LVDS
SU
SU
MSD6308RTEM/ MSD6308RTEMB
SPDIF
A
ATV&DTV Decoder
D
D
D
D+ / D
W
RJ45 Network
D
D
D
Antenna
W
3.3vSTB in
POWER
PPLY
TPA3110D
12v in
Audio R/L CH out
DTV CC/CA
Panel
Transimiter
DDR InterfaceLVDS Interface
Be in 2G DDR3
Content protection
PCMCIA for MS08BP Nandflash date processor
CICAM
AV in CVBS+ Audio R/L
VGA
Video& sound signal processor
Key/IR control
Internet connectivity
Audio R/L out
HDMI TMDS
1GDDR3 option For MS08GP
Nandflash,
MS08BP /MS08GP 2G
MS08BPA 4G
Key/IR board
IFI
U SB
MS08GP NXP TDA18275
-
RX+/RX-
H
H
MI2
MI1
H MI3
FAT+ / FAT-
MS08BP/BPA Rafael RT840D
ntenna /Cable
(ATV/DTV)
(ATV/DTV)
__
110V~
驱动
A
AMP
3.18A
A
A
240V
源模
1
2
?V
MAX:3.5A
12V
MS08BP+ POWER
LED
1A/1.5
0.8A
BL_ON_OUT DIM PWM
5W*2/80% 8W*2/85%
Panel/0.8APMK65XP
MPS1495/3A
待机通过POWER_ON 控制
MPS1495/3A
1.1A/0.9A
3.3 STB/320MA/263M
PMK65XP
待机通过POWER_ON 控制
5V
2.2A/1.7A
TU1_3.3V/180MA
3.3V NOR/150MA/100mA AS1117-223
1.25A
440MA/390
Panel on/off
MP2143 1.1V CORE/1.8A/1.6A
MHL/500mA
USB/500mA*1 WIFI/250m
1.2V_T2 DEMOD/165mA
AS1117-223
1.5VDDR/500mA/200MA
8 7 6 5
4 3 2 1
For chip core power supply
F
BL_ON
VCCK
T
C019
Min 1.16V/ Max 1.24V
R026
39K
22U
NC
R028
4K7
NC
4K7
NC
C020
10U
R029
R027 1K
NC
VCCK
@max3A
DGND
Q010
2N7002K
NC
C045
0.01U
R005
220R
T
POWER_ON
T
POWER_ON
BL_ON
C001
0.01UR003
DGND
DIM_PWM
T
DIM_PWM
DGND
C002
0.01U
12V TO 5V
12V
C009
10U/16V
10U/16V
C008
POWER_ON
NC
DGND
C007
0.1U
R007
100K
NC
R046
1K
R008 82K
0.1U
DGND
C006
R011
10K
R010 82K
33R
C005
1000P
R036
U000
5
7 8
BST
VCC FB
MP1495
R034 33K
C013
0.1U
GND
SWEN/SYNC
IN
AAM
4 36 2 1
DGND
R012
NC/10R
DGND
R013
C004
NC/470P
C003
L001
6.8UH
0R
15P
R014
39K
R009
R035
6K8
470R
C010 220U
10V
DGND
Typ 3A
C011
10U
C012
0.1U
5V
5V
5V
DGND
PGND
4
SW
(Vin=2.5V-5.5V)
C015 10U
If Vout=1V Set R015=150K R017=4.7K R016=220K
If Vout=1.2V Set R015=150K R017=0R R016=150K
If Vout=1.18V Set R015=150K R017=120k R016=33K
C016
0.1U
DGND
If Vout=1.5V Set R015=150K R017=8.2K R016=91K If Vout=1.8V Set R015=150K R017=6.2K R016=68K
BOM COST=1.22RMB
3
VIN
2
PG
1
Fixed Fsw=1.2MHZ
For timing sequence
Fixed OCP=4.2A
L000 1UH
U001
MP2143
R018
510K
OUT
AGND
FB
EN
5 6 7 8
0.1U
DGND
Vref=0.6V
C017
150K
DGND
R015
R017
120K
R016
33K
C018
DGND
22U
3_3VSB
VID0
3_3VSB
R000
2K2
R001
10K
DGND
DIM_OUT
330R
R004 330R
DIM_OUT
R006
33K
POWER_ON_OUT
BL_ON_OUT
BL_ON_OUT
E
F
E
VCC=0.8(39/7.27+1)=5.09V
5V NORMAL POWER
D
12V TO 3V3
C035
22U/6.3V
Z3_3VSVB
T
Typ 3A
DGND
C036
10U
3_3VSB
3_3VSB
C021
0.1U
12V
C033 1000P
33R
R039
U002
5
7 8
BST
VCC FB
R032
100K
C030
10U/16V
10U/16V
C029
C
DGND
NC
C031
0.1U
R033 82K
0.1U
DGND
C032
R022
10K
R019 82K
MP1495
R021 33K
C038
0.1U
GND
SWEN/SYNC
IN
AAM
4 36 2 1
DGND
R020
NC/10R
DGND
R030
C034
NC/470P
C047
L002
6.8UH
0R
15P
R031
39K
R037
12K
R038
330R
VCC=0.8(39/12.33+1)=5.24V
DGND
3_3VSB
POWER_ON
LO =>Panel OFF HI =>Panel ON
R041
4K7
R042
3K3
R040
33K
B
C025
0.1U
DGND
C
BT3904
E
Q002
Q001
PMV65XP
S
G
R043 2K7
3_3V
T
D
D
3_3V
For DDR3 power supply
C024
0.1U
3_3V
AS1117AD
4
4
U004
GND/ADJ
OUT
VIN
3
2
C027 0.1U C028
R024
1
330R
R025
68R
10U
DGND
Output 1.5076V=1.25*(1+68/330) & 200mA
FOR DDR3 power supply
10U
C026
1V5
T
1_5V
C
3V3 POWER SUPPLY
B
For +1.2V T2 DEMOD power supply
DGND
LD1117S12
U006
VIN
3
OUT
2
GND/ADJ
1
4
4
10U/10V
Z+1_2V_DEMOD
T
C043
C042
DGND
0.1U/16V
C044
22U/6.3V
3_3V
C040 10U
C041
0.1U
A
DGND
THIS DRAWING CANNOT BE COMMUNICATED TO UNAUTHORIZED PERSONS COPIED UNLES S PERMITTED IN WRITING
DGND
+1_2V_DEMOD
B
...
...
...
...
Index-Lab
Last saved :
5
DD-MM
DD-MM
DD-MM
DD-MM
DATE
... ... ... GJZ
...
...
...
...
DESCRIPTION Last modifNAME
11-27-2014_14:07
4678
...
...
...
...
SBU :
TCLNO:
40-MS08BP-MAB2HG
DESIGNATION
...........
ON: BY:
DRAWN
TCL Thomson Electronics Ltd. B Building, TCL Tower, Nanhai Road Nanshan District, Shenzhen, Guangdong Tel +86-755-3331xxxx Fax +86-755-3331xxxx
CHECKED
DD-MM-YY
ON: BY:
......
PAGE:
OF :
1
7
A
3 2 1
FORMAT DIN A2
DGND
P915
CVBS
R
GND
L
AV1 IN
1 2 3
4 5
ZAV1-GND1
T
F911
Mini jack for AV Input
NEARLY CONNECTOR
T
ZAV_VIN
AV-VIN
AV/YPBPR-LIN
AV/YPBPR-RIN
AV-VIN
F902
DGND
R974
75R
C935
NC/47P
DGND
NEARLY IC
R248
33R
R247
68R
C265
0.047U
C264
0.047U
AV1_V_IN
VCOM0
Must be differential 100ohm
TXVP_0
TXVN_0
RXVP_1
RXVN_1
TXVP_0]
close to U300
RXVP_1TXVN_0
F901F900RXVN_1
ETHERNET
WLAN CONNECTORIPTV IN
RJ45
U900
10 9 8
7 6 5 4 3 2 1
12 11
P902
C905
0.1U
DGND
C907
0.1U
1 2 3 4
TS8121CLF
5 6 7 8 9
16
NET_TX1P
15
NET_TX1N
14 13 12
NET_RX1P
11 10
NET_RX1N
R917
75R
R919
75R
1000P
R918
75R
C916
1000P
R920
75R
C916A
NET_TXC
DGND
NET_RXC
RXC
RX1N
TXC RX1P TX1N
TX1P
DGND
NET_RXC
T
NET_RX1N
NET_TXC
T T
NET_RX1P NET_TX1N
T T
NET_TX1P
T
DGND
DGND
AV/YPBPR-LIN
AV/YPBPR-RIN
ZAV-L
T
DGND
ZAV-R
T
F905
close to conn.
R977 10K
R978 10K
F906
DGND
12K
R979
560P
DGND
C937
R980
12K
560P
close to SOC
C271 2U2
C272 2U2
C936
AV/YPBPR_L_IN
AV/YPBPR_R_IN
VGA INPUT CIRCUIT
C940
17
11
12
13
14
10 15
16
C941
6
1 7
2 8
3 9
4
5
100P
NC
100P
NC
ZVGA-GND
T
VGA_HS_IN
VGA_VS_IN
DGND
ZVGA-TX
T
T
ZVGA-SDA
T
VGA_SDA
75R
R991
ZVGA-R
VGA_TXD
75R
R990
R989
T
T
75R
VGA_SDA
VGA_TXD
VGA_SCL
VGA_RED
ZVGA-G
ZVGA-HS
T
VGA_HS
VGA_BLU
ZVGA-B
10K
R988
R902A
4K7
VGA_GRN
T
ZVGA-VS
VGA_VS
VGA_RXD
10K
R987
3_3VSB
4K7
VGA_RXD
R256
33R
R257
33R 68R
R258
100R
R985
33R
R259
T
ZVGA-RX
T
ZVGA-SCL
VGA_SCL
R903A
close to Mstar IC
C273 0.047U
C274 0.047U C275 0.047U
C276 0.047U
R986
100R
R981
R982
R983
R984
VGA_TXD
100R
100R
100R
100R
VGA_SDA
VGA_RED
VGA_GRN
VGA_RED_IN
VGA_GRN_IN
VGA_SOG_IN
VGA_HS_IN
VGA_BLU_IN
VGA_VS_IN
VGA_VS
VGA_HS
VGA_BLU
VGA_RXD
U0TX
U0RX
VGA_RED_IN
VGA_GRN_IN
VGA_SCL
U0TX
U0RX
VGA_SOG_IN
VGA_HS_IN
VGA_BLU_IN
VGA_VS_IN
P918
Mini jack for AUDIO Output
ZAVOUT-GND
T
ZAVOUT-R
T
AV-ROUT
GND
4 2
L R
3 1
DGND
F922
F923
ZAVOUT-L
T
AV-LOUT
C938
2U2
2U2
C939
DGND
C277
1000P
C278
1000P
DGND
CLOSE TO SOC
R254 220K
AVOUT1_L_OUT
AVOUT1_R_OUT
R255
220K
P917
DGND
DGND
F912
DGND
F913
F914
F915
F916
F917
F918
F919
F920
HDMI/MHL
DGND
HDMI1_SCL HDMI1_SDA
H1_HPD_OUT
H1_HPD
H1_SCL
H1_SDA
H_CEC
H1_5V
R924 100R
R925 100R
R926
10K
H1_HPD
H1_SCL
H1_SDA
H_CEC
H1_5V
R928
4K7
CEC
R922 R923 47K
B
47K
C
E
R921 100R
R927
1K
Q402
BT3904
H1_RX2+
H1_RX2-
H1_RX1+
H1_RX1-
H1_RX0+
H1_RX0­H1_RXC+
H1_RXC-
H_CEC
H1_ARC
H1_SCL H1_SDA
H1_5V
H1_HPD
DGND
P903 1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19
RX2+
GND1
RX1+
RX1-
RX0+
GND3
RXC+
RXC-
NC1
NC2
DDCCLK
DDCDA
VCC
RX2-
GND2
RX0-
GND4
GND5
HPD
DGND
HDMI3_SCL
HDMI3_SDA
H3_HPD
H3_SCL
H3_SDA
H3_5V
H3_HPD_OUT
F3
R932 100R
R933 100R
R934
10K
H3_HPD
H3_SCL
H3_SDA
H_CEC
H3_5V
R936
4K7
47K
R930 R931 47K
B
H3_RX2+
H3_RX2-
H3_RX1+
H3_RX1-
H3_RX0+
H3_RX0-
H3_RXC+
H3_RXC-
H_CEC
H3_SCL H3_SDA
H3_5V
R935
1K
C
Q403
BT3904
E
H3_HPD
DGND
P904 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
RX2+
GND1
RX1+
RX1-
RX0+
GND3
RXC+
RXC-
NC1
NC2
DDCCLK
DDCDA
VCC
RX2-
GND2
RX0-
GND4
GND5
HPD
DGND
HDMI2_SCL
HDMI2_SDA
H2_HPD
H2_SCL
H2_SDA
F2
H2_5V
R943 100R
R944 100R
H2_HPD
H2_SCL
H2_SDA
H_CEC
H2_5V
5V
R941
4K7
H2_HPD_OUT
R942
10K
MHL_DETECT
R945
33R
H2_RX2+
H2_RX2-
H2_RX1+
H2_RX1-
H2_RX0+
H2_RX0-
H2_RXC+
H2_RXC­H_CEC
H2_SCL H2_SDA
H2_5V H2_HPD
DGND
P905 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
RX2+
GND1
RX2-
RX1+
GND2
RX1-
RX0+
GND3
RX0-
RXC+
GND4
RXC-
NC1
NC2
DDCCLK
DDCDA
GND5
VCC
HPD
H1_ARC
DGND
F403
C926
2U2
DGND
R929
0R
H1_ARC_OUT
AVDD5V_MHL
R937
5R6
H2_5V
DGND
MHL_DETECT
C918
0.047U
DGND
100R
R939
300K
R938
MHL_CABLE_DET
MHL_EN
MHL_CABLE_DET
R947
5V
R946
NC/100R
1K
R948
NC/10K
C919
0.1U
DGND
C910
10U
C911
0.1U
1
2
U901
VIN
GND
FAULTEN/EN#
RT9728B
VOUT
ILIM
6
5
43
R949
18K
DGND
C912
100U
10V
DGND
C913 10U
C914
0.1U
H2_5V
5V
USB CONNECTOR
R951
0R/1206/NC
U902
1
VOUT
2
GND
RT9711A
VGA UART R954/R955 NOT USE
C915 10U
DGND
R950
4K7
5
VIN
4 3
EN/EN# NC
USB1_D-_IN
USB1_D+_IN
DGND
C906
100U
10V
DGND
C917
10U/16V
R956
R957
5V_USB
USB1_D-
2R2
2R2
GND
D+D-
USB_5V
TTT
T
USB1_D+
DGND
3_3VSB
SPDIF
T
Z2
R962
4K7
1000P
R958
47K
F103
C923
IR
T
120R
DGND
5V
0.1U
C921
R963
C920
F1
0.1U
C953
2P2
NC
SPDIF
T
T
Z1
T
USB2_D+
USB2_D-
C954
2P2 NC
2
1
WIFI_ON
P912
220R
BLACK
R900
220R/NC
R901
3_3V
WIFI_EN
P909
P910
3_3VSB
1
KEY1
2
GND
3 4
3_3VSB
1
IR
2
GND
3
R-LED
4
NC
5
NC
C198 CLOSE TO connect
KEY
T
KEY
3_3VSB
T
3_3VSB
DGND
P908
R964
220R
R904A
NC
6 5 4 3 2 1
C931
33P
DGND
0R
R965 2R2
T
T
USB2_D+
USB2_D-
DGND
R966 2R2
C930
SPDIF_OUT
0.1U
close to SOC
P907
1
VCC-1
2
DNEG-1
3
DPOS-1
4
GND-1
5 6
MNT-HOLE1
MNT-HOLE2
WIFI
2
R961
220R
D100
3
DGND
IR_IN
C924
0.1U
DGND
1
DGND
R244
22K
3_3VSB
0BAV99NC/
C248
0.1U
KEY_IN
R244/C248 CLOSE TO IC
DGND
C925
0.1U
KEY_IN
LED
T
DGND
1K
R960
LED_OUT
LED_OUT
P911
39
TXO0+ TXO1+ TXO2+ TXOC+
37
35
33
31
TXO3+
29 30
TXO4+
27
25
23
21
TXE0+ TXE0­TXE1+ TXE2+ TXEC+ TXE3+
TXE4+
19
17
15
13
11
9 7 5 3
DGND
1 2
40 38 36 34 32
28 26 24 22 20 18 16 14 12 10 8 6 4
C927
0.1U
TXO0-
TXO1­TXO2­TXOC-
TXO3-
TXO4-
TXE1­TXE2-
TXEC­TXE3­TXE4-
PANEL_12V
DGND
SEL_LVDS
Z3
TT
PANEL_VCC
DGND
T
DGND
LVDS_SEL
R967
100R
DGND
3_3VSB
R238
22K
C260 10U
DGND
1
R239
3
D210
0BAV99
47K
2
B
Q200
BT3906
E
C
47KR240
2U2
C503
DGND
C261
NC/0.1U
NC
Close to SOC
MCU_RESET
MCU_RESET
Reset=H
Normal=L
BAT54C
T
R241
3K3
D200
1 2
3
STB_RST
Normal=H Standby=L
3_3VSB
Q201
E
B
C
BT3906
If 24v<17.8V then reset_H
If 12v<8.3V then reset_H
12V
DGND
R242
56K
R243
27K
VCCK
3_3VSB
C229
10U
C220
2U2
C230
0.1U
core power CLOSE MAIN IC
C250
0.1U
0.1U
C222
C221
2U2
C251
10U
NC
C252
2U2
NC
C251/C252 CLOSE MAIN IC AT BOTTOM
STANDBY POWER_3.3
C231
C232
0.1U
0.1U
0.1U/NC
C223
0.1U
C233
C224
0.1U
1_5V
1000R C234
0.1U/NC
22U/6.3V
1_5V
R231
C225
C300
10U
DGND
AVDD_DMPLL
C226
0.1U/NC
C301
2U2
C235
0.1U/NC
L201 600R
C227
0.1U
C302
C303
0.1U
0.1U
DDR3 POWER
3_3VSB
+1_15V_VDDC_RX
C249
C228
0.1U
0.1U
DGND
C304
0.1U
C305
0.1U/NC
R232
0R
C306
0.1U/NC
AVDD_AU
CLOSE MAIN IC
C348
0.1U
C236
C237
0.1U
0.1U/NC
C349
0.1U
12V
PANEL_ON
LO =>Panel OFF HI =>Panel ON
5V
R969
4K7
R970
3K3
R969A
0R 0R
R968A
33K
R968
B
C928
0.1U
C
BT3904
E
DGND
T
IF+
Q901
PMV65XP
S
Q900
R971 2K7
PANEL_VCC
T
D
G
C929
0.1U
PANEL_VCC
AGC
T
100R
TUNER_AGC
R105
NXP TUNER R210 IS 4K7
IF_AGC
R211
0R
10K
TU1_VCC
R210
IF-AGC
DIM_OUT
R354 22R
TUNER
MS_DIM_OUT
AUVRM
L200
1000R
DGND
For TUNER power supply
DGND
C238
0.1U
C239
0.47U
close to SOC
AUVAG
XTALO
XTALI
R209
0R
R212
NC/1M
24M
X24M1
C240
30P
C241
30P
DGND
DGND
3_3V
NORMAL POWER 3.3V
C243
C242
0.1U
10U
DGND
DGND
C244
0.1U
C245
1U
TU1
IF_AGC
IF_P IF_N
NC3
NC2 GND SDA
SCL
3V3
NC1
C216
0.022U
DGND
Close to SOC
AGC
Tuner power supply
4
VIN
3
4
OUT
0.1U
2
GND/ADJ
1
GND
5V
AZ1117
C112
10U
10V
U100
C107C111
0.1U
CLOSE TUNER
L100
1000R
C108
22U
TU1_VCC
For XF-3SDT-H ( Rafael MICRO RT840D)
Close to SOC
TUNER_FAT+
TUNER_FAT-
R270
220R
220R
R271
R272
470R
NC
C211
C212
56P
56P
R273
DGND
1.8K
1.8K R274
C214
0.1U
C215
0.1U
FAT+_D
FAT-_D
DGND
C106
0.1U
TUNER_FAT+
TUNER_FAT-
T
TUNER-GND
R101 33R
R102
NXP TUNER C106 IS 0.47UF
TU1_VCC
R100
R104
4K7
4K7
TU1_SCL
TU1_SDA
10 9 8 7 6 5
T_SDA
4
T_SCL
3 2 1
T
C104
22P
IF-
DGND
T_SDA
T T
C105
22P
DGND
T_SCL
22P
C100
DGND
33R
TU1_VCC
C103
10U
DGND
DGND
C102
22P
TU_VCC
T
U200
VGA_GRN_IN
VGA_BLU_IN
VGA_SOG_IN
VGA_HS_IN
VGA_VS_IN
VGA_RED_IN
AV/YPBPR_L_IN AV/YPBPR_R_IN
AVOUT1_L_OUT AVOUT1_R_OUT
HP_L HP_R
MCU_RESET
DGND
HD1_PR_IN
HD1_Y_IN
HD1_PB_IN
HD1_SOG_IN
AUVAG AUVRM
IR_IN
XTALI
XTALO
HD1_Y_IN-
M3
RIN0P
L2
GIN0M
L3
GIN0P
K2
BIN0P
M5
HSYNC0
M4
VSYNC0
N2
RIN1P
N1
GIN1M
N3
GIN1P
M2
BIN1P
M1
SOGIN1
R2
RIN2P
R3
GIN2M
P2
GIN2P
P3
BIN2P
K4
HSYNC2
M6
VSYNC2
U5
LINE_IN_1L
V5
LINE_IN_1R
T5
LINE_IN_2L
T4
LINE_IN_2R
V4
LINE_IN_3L
U4
LINE_IN_3R
V2
LINE_OUT_0L
V1
LINE_OUT_0R
W4
EARPHONEOUTL
Y5
EARPHONEOUTR
V3
VAG
U2
VRM
A3
I2S_OUT_BCK
B3
I2S_OUT_MCK
C3
I2S_OUT_WS
A2
I2S_OUT_SD
E4
I2S_IN_WS/T2_RESET
F5
I2S_IN_BCK/T2_I2CS_SCL
E5
I2S_IN_SD/T2_I2CS_SDA
P9
SPI1_DI
R8
SPI1_CK
R9
SPI2_DI
R10
SPI2_CK
F6
IRIN
D3
RESET
AA2
XTALIN
AA3
XTALOUT
F9
TESTPIN
U200
PHY
RGB
USB
CVBS
CVBS_OUT
MSD6308RTMN
U200
Analog audio
I2S
demod
SPDIF
MHL
MSD6308RTMN
RN RP TN TP
DM_P0
DP_P0
DM_P1
DP_P1
CVBS1P CVBS0P
VCOM0
HDMI
B2 B1
TXVN_0
C2
TXVP_0
C1
C4
USB2_D+
B4 Y10
USB1_D-_IN
W10
USB1_D+_IN
T1 T3 T2 R1
A_RX0N
A_RX0P
A_RX1N
A_RX1P
A_RX2N
A_RX2P A_RXCN A_RXCP
DDCDA_CK DDCDA_DA HOTPLUGA
C_RX0N C_RX0P C_RX1N C_RX1P C_RX2N C_RX2P
C_RXCN
C_RXCP
DDCDC_CK DDCDC_DA HOTPLUGC
D_RX0N D_RX0P D_RX1N D_RX1P D_RX2N D_RX2P
D_RXCN
D_RXCP
DDCDD_CK DDCDD_DA HOTPLUGD
PAD_ARC0
SPDIF_IN
SPDIF_OUT
MHL_CABLE_DETMCP_TEST
MHL_VBUS_EN
RXVN_1 RXVP_1
USB2_D-
AV1_V_IN
CVBS_OUT
CEC
T
ZCVBS_OUT
H1_RX0-
H2 J3
H1_RX0+
J2
H1_RX1-
H1_RX1+
J1
H1_RX2-
K3 K1
H1_RX2+
G2
H1_RXC-
H3
H1_RXC+
HDMI1_SCL
H6
HDMI1_SDA
H5
H1_HPD_OUT
G4
H2_RX0-
W7
H2_RX0+
Y8
H2_RX1-
W8 Y9
H2_RX1+
H2_RX2-
AA9
H2_RX2+
W9 AA7
H2_RXC-
Y7
H2_RXC+
HDMI2_SCL
W6 AA6
HDMI2_SDA
H2_HPD_OUT
Y6
H3_RX0-
E2 F3
H3_RX0+
F2
H3_RX1-
F1
H3_RX1+
H3_RX2-
G3
H3_RX2+
G1
H3_RXC-
D2
H3_RXC+
E3 J4
HDMI3_SCL
L6
HDMI3_SDA
K6
H3_HPD_OUT
H1_ARC_OUT
J5 J6
E6 A4 AA10P8 W5
CEC
SPDIF_OUT
MHL_CABLE_DET
MHL_EN
NC/
C247
33P
DGND
PCM_D3
PCM_D4
PCM_RESET PCM_IRQA_N
PCM_IOWR_N
PCM_OE_N
PCM_IORD_N
PCM_WE_N
PCM_CD_N
PCM_REG_N
PCM_WAIT_N
close to SOC
PCM_D0 PCM_D1
PCM_D2
PCM_D5
PCM_D6
PCM_D7
PCM_A0 PCM_A1 PCM_A2 PCM_A3 PCM_A4 PCM_A5 PCM_A6 PCM_A7
PCM_A8
PCM_A9
PCM_A10
PCM_A11
PCM_A12
PCM_A13
PCM_A14
PCM_CE_N
NAND_ALE
NAND_WPZ
NAND_CEZ
NAND_CLE NAND_REZ
NAND_WEZ
NAND_RBZ
U20
PCM_D0
V15
PCM_D1
AA18
PCM_D2
Y20
PCM_D3
T16
PCM_D4
W18
PCM_D5
T14
PCM_D6
Y21
PCM_D7
Y18
PCM_A0
W17
PCM_A1
Y17
PCM_A2
W16
PCM_A3
Y16
PCM_A4
AA16
PCM_A5
W15
PCM_A6
AA15
PCM_A7
Y19
PCM_A8
AA19
PCM_A9
AA20
PCM_A10
W21
PCM_A11
V20
PCM_A12
W20
PCM_A13
V17
PCM_A14
W19
PCM_RESET
U16
PCM_IRQA_N
U17
PCM_IOWR_N
T15
PCM_OE_N
V16
PCM_IORD_N
U15
PCM_CE_N
U14
PCM_WE_N
V19
PCM_CD_N
V18
PCM_REG_N
V21
PCM_WAIT_N
T8
NAND_ALE
T9
NAND_WPZ
V7
NAND_CEZ
U9
NAND_CLE
V9
NAND_REZ
U8
NAND_WEZ
U7
NAND_RBZ
AMP_MUTE
MS_DIM_OUT
LG_DIM_OUT
KEY_IN LED_OUT
HP_DET_IN
SPI_SDI
U0RX
U0TX
PCMCIA_VCC_EN
WIFI_EN
VID0 PANEL_ON
POWER_ON_OUT
BL_ON_OUT PM_CONFIG0
STB_RST
PM_CONFIG1
MSD6308RTMN
T18
3D_EN/PCM_PWR_EN
T17
AMP_MUTE
U18
BRI_ADJ
K5
PWM_PM
F4
KEY0
D4
LED_R
G7
ARC_DET
G5
SAR3
D6
PM_SPI_CK
E7
PM_SPI_DI
D7
PM_SPI_DO
F7
PM_SPI_CZ1N
L5
UART0_RX
L4
UART0_TX
L15
M_I2C_SLC
K15
M_I2C_SDA
L16
UART_RX2
L17
UART_TX2
W3
VID0
E8
PANNEL_ON/OFF
D1
PWR_ON/OFF
D8
VBL_CTRL
U3
PMCONFIG0
D5
3D_LR_IN
G6
PMCONFIG1
W14
TS0_D0
W13
TS0_D1
W11
TS0_D2
Y15
TS0_D3
Y13
TS0_D4
Y12
TS0_D5
Y14
TS0_D6
W12
TS0_D7
TS1_D0 TS1_D1 TS1_D2 TS1_D3 TS1_D4 TS1_D5 TS1_D6 TS1_D7
VIFP
VIFM
IFAGC
TGPIO0 TGPIO1
AA12 AA13 Y11
T13 U13 T12 U10 T11 U11 T10 V12 V13 U12 V10
W2 W1
Y3
AA4 Y4
Y2 Y1
TS0_CLK TS0_VLD
TS0_SYNC
TS1_CLK TS1_VLD
TS1_SYNC
T_I2C_CLK T_I2C_SDA
U200
PWM
SAR
SPI
GPIO_PM
MSD6308RTMN
TS0_D0
TS0_D1
TS0_D2 TS0_D3 TS0_D4
TS0_D5
TS0_D6
TS0_D7 TS0_CLK TS0_VLD TS0_SYNC
TS1_CLK
TS1_VLD
TS1_SYNC
FAT+_DVCOM0
FAT-_D
IF-AGC
TU1_SCL TU1_SDA
LVDS
TCON
TS1_D0 TS1_D1 TS1_D2
TS1_D3
TS1_D4
TS1_D5
TS1_D6
TS1_D7
LVA0N LVA0P LVA1N LVA1P LVA2N
LVA2P LVACKN LVACKP
LVA3N
LVA3P
LVA4N
LVA4P
LVB0N
LVB0P
LVB1N
LVB1P
LVB2N
LVB2P LVBCKN LVBCKP
LVB3N
LVB3P
LVB4N
LVB4P
LDE
LCK LVSYNC LHSYNC
TCON0 TCON1 TCON2 TCON3 TCON4 TCON5 TCON6 TCON7
N19 N21 N20 P19 P20 R19 R20 R21 T19 T21 T20 U19
H20 J19 J20 J21 K19 K21 K20 L19 L20 M19 M20 M21
G20 H19 G21 G19
J16 J17 J15 K17 J18 K18 K16 L18
TXE0-
TXE0+
TXE1-
TXE1+
TXE2­TXE2+ TXEC­TXEC+
TXE3-
TXE3+
TXE4­TXE4+
TXO0-
TXO0+
TXO1-
TXO1+
TXO2-
TXO2+
TXOC-
TXOC+
TXO3­TXO3+
TXO4­TXO4+
+1_2V_DEMOD
C290
0.1U
CLOSE TO MAIN IC
Chip config
3_3VSB
4K7
R213
NC/
R214
NC/
R215
R216 4K7
R217
NC/
R218 R219
R220
DGND
4K7
4K7
4K7
4K7
4K7
NC/
4K7
DGND
C289
0.1U
PM_CONFIG0
SPI_SDI
PM_CONFIG1
LG_DIM_OUT
VCCK
+1_15V_VDDC_RX
C246
1U
1_5V
DGND
L11
VDDC
M11
VDDC7
N12
VDDC1
N13
VDDC2
N14
VDDC3
N15
VDDC4
P12
VDDC5
P13
VDDC6
P14
AVDDL_MOD
M12
DVDD_RX_1
M14
DVDD_RX_2
M13
DVDD_DDR
A7
DVDD_RX_1_1
B7
DVDD_RX_2_1
C7
DVDD_DDR1
N11
MCP_VDDC
P11
MCP_VDDC1
F8
DVDD_NODIE
C5
AVDD_DDR0_D
K12
AVDD_DDR0_D1
L12
AVDD_DDR0_D2
K11
AVDD_DDR0_CMD
C6
AVDD_DDR1_D
K14
AVDD_DDR1_D1
L14
AVDD_DDR1_D2
K13
AVDD_DDR1_CMD
L13
AVDD_DDR1_CLK
B6
AVDD_DRAM1
B5
AVDD_DRAM
A6
GND9
A13
GND
A15
GND1
A18
GND2
B12
GND3
B14
GND4
B16
GND5
B17
GND6
B19
GND7
B20
GND8
C9
GND10
C10
GND11
C21
GND12
D9
GND13
E20
GND76
F11
GND14
F13
GND15
F15
GND16
F17
GND17
F19
GND18
F21
GND19
G8
GND77
G9
GND20
G10
GND21
G11
GND22
G12
GND23
G13
GND24
G14
GND25
G15
GND26
G16
GND27
G17
GND28
G18
GND29
H8
GND30
H9
GND31
H10
GND32
U200
AVDD_DVI_USB_MPLL1
MSD6308RTMN
PM_CONFIG1
LG_DIM_OUT
AVDD_NODIE
AVDD_DVI_USB_MPLL
AVDD_AU33
AVDD3P3_DMPLL
VDDP
AVDD_MOD
AVDD_MOD1
AVDD_PLL
AVDD5V_MHL
GND_EFUSE
GND70 GND71 GND72 GND73 GND74 GND75 GND60 GND61 GND62 GND63 GND64 GND65 GND66 GND67 GND68 GND69 GND78 GND33 GND79 GND80 GND34
GND35 GND36 GND37 GND38 GND39 GND40 GND41 GND42 GND43 GND44 GND45 GND46 GND47 GND48 GND49 GND50 GND51 GND52 GND53 GND54
GND81 GND55 GND56 GND57 GND58 GND59
GND82 GND83 GND84
Chip config PIN
PM_CONFIG0
SPI_SDI
J7 K7
L7 R6
AVDD_DMPLL
R5 R15 R16
R17 R18
AVDD5V_MHL
V6
H7
H11 H12 H13 H14 H15 H16 H17 H18 J8 J9 J10 J11 J12 J13 J14 K8 K9 K10 L8 L9 L10
M7 M8 M9 M10 N4 N5 N6 N7 N8 N9 N10 P4 P5 P6 P7 P10 P15 P16 P17 P18
R4 R7 R11 R12 R13 R14
T6 T7 U6
LEVEL
H
L
H
H
3_3VSB
AVDD_AU
3_3V
DGND
DGND
DGND
MUTE Circuit
3_3VSB
AMP_MUTE
3_3VSB
R604
4K7
10K
R606
R605
DGND
4K7
NC
B
R609
4K7
C
E
DGND
Q602
BT3904
MUTE
T
SD
HP_L
HP_R
HP_L
HP_R
C628 1U
C629 1U
close to SOC
R635
1K
C630
6.8N
NC/100K
DGND
R620
1K
C631
6.8N
DGND
R636
R621
NC/100K
12VA
AMP_L
R612
10R
C636
R611
100R
C604
1000P
CLOSE AMP IC
1U/50V
DGND
AMP_R
10K
R615
100R
CLOSE AMP IC
Power AMP TPA3113D2
R629 100K
R614
SD
1UC605 1UC606
1000P
DGND
C609
R613 10K
DGND
DGND
R610 1K
U600
1 2
FAULT
GAIN0
GAIN1
1UC607 1UC608
DGND
3 4 5 6 7 8
9 10 11 12 13 14
LINP
LINN
GAIN0
GAIN1
AVCC
AGND
GVDD
PLIMIT
RINN
RINP
NC
PBTL
TPA3113D2
1UC602
1UC603
PVCCL2SD
PVCCL1
BSPL
OUTPL
PGND2
OUTNL
BSNL
BSNR
OUTNR
PGND1
OUTPR
BSPR
PVCCR2
PVCCR1
C610
1000P
28 27 26
C612
0.22U
C611
0.1U
25 24
C619
0.22U
DGND
C618
0.22U
23 22 21 20 19 18 17 16
DGND
0.22U
C623
15
C625
1000P
C626
0.1U
DGND
DGND
10R
DGND
DGND
DGND
10R
C613
C624
16V
R622
12VA
10R
R616
R617
330P
10R
R628
C600
220U
330P
C616
330P
C620
330P
L600
392170
DGND
12V
L601
22UH
L602
220R/NC
L603
22UH
L604
220R/NC
L605
220R/NC
L606
22UH
L607
220R/NC
L608
22UH 12VA
OUTLP
0.1U/50V
OUTLN
OUTRN
C621
0.1U/50V
OUTRP
C614
C6170.1U/50V
0.1U/50V
C622
DGND
DGND
R631 10K
R633
NC/0R
3_3VSB
DGND
OUTRP
OUTRN
OUTLP
OUTLN
R632
NC/10K
R634
OUTRN
0R
OUTRP
TT
OUTLPOUTLN
T T
GAIN1
L L H HLH
GAINGAIN0 20dB 26dB
H
32dB
L
36dB
GAIN1GAIN0
C641
OUTLP
0.1U
C642
0.1U
OUTRNOUTRP
OUTLN
R+
R-
1
2
RED
P600
L+
1
L-
2
WHITE
P601
R230
DGND
240R
U200
E11
B_A[0]
F12
B_A[1]
D10
B_A[2]
B10
B_A[3]
E15
B_A[4]
B11
B_A[5]
F14
B_A[6]
C11
B_A[7]
D14
B_A[8]
A12
B_A[9]
F16
B_A[10]
D13
B_A[11]
D15
B_A[12]
C12
B_A[13]
E13
B_A[14]
B_CASZ B_RASZ
B_WEZ
B_ODT B_BA[0] B_BA[1] B_BA[2]
B_RST B_CKE
B_DQSL
B_CS0
A20 A16 C19 C15 C20 C14 B21 B15 F18 D19 D17 E21 E19 D20 D18 F20 B9 C8 D11 C16 D21 B8 A9 D16 A10 F10 E17 C13 B13 A19 C18 B18 C17 D12
PCMCIA_VCC_EN
R993
100
PCM_CE_N
PCM_WE_N
R915
4K7
T
T
TS1_CLK
TS0_CLK
B_DQL[0] B_DQL[1] B_DQL[2] B_DQL[3] B_DQL[4] B_DQL[5] B_DQL[6]
B_DQL[7] B_DQU[0] B_DQU[1] B_DQU[2] B_DQU[3] B_DQU[4] B_DQU[5] B_DQU[6] B_DQU[7]
B_DQML
B_DQMU
B_MCLK
B_MCLKZ B_DQSLB
B_DQSU
B_DQSUB
ZQ
MIU0
MIU1
E9
C945 10U
ZCE_N
ZWE_N
T
ZTS1_CLK
T
ZTS0_CLK
5V
0.1U
C946
R993A
DGND
PCM_OE_N
PCM_RESET
PCM_WAIT_N
10K
NC
MSD6308RTMN
+5V_PCMCIA
PCM_IRQA_N
PCM_WAIT_N
4K7
4K7
R994
R995
PCMCIA
C952
0.1U
T
ZOE_N
T
ZRESET
T
ZWAIT_N
+5V_PCMCIA
TS0_CLK
Close to CI SLOT
NC/10P
C286
DGND
R992
0R/0805
NC
U903
5
VIN
VOUT
GND
4 3
EN/EN# NC
RT9711A/NC
DGND
PCM_CD1_N
TS0_D3
TS0_D4 TS0_D5
TS0_D6
TS0_D7
PCM_IORD_N
PCM_IOWR_N
TS1_SYNC
TS1_D0 TS1_D1
TS1_D2 TS1_D3
TS1_D4 TS1_D5 TS1_D6 TS1_D7
PCM_RESET
PCM_WAIT_N
PCM_REG_N
TS0_VLD
TS0_SYNC
TS0_D0
TS0_D1 TS0_D2
PCM_CD2_N
1
2
DGND
Z+5V_PCMCIA
C947
P920
35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68
T
0.1U
DGND
+5V_PCMCIA
10U
C948
DGND
1 2
PCM_D3
3
PCM_D4
4
PCM_D5
5
PCM_D6
6
PCM_D7
7
PCM_CE_N
8
PCM_A10
9
PCM_OE_N
PCM_A11
10 11
PCM_A9
12
PCM_A8
13
PCM_A13
14
PCM_A14
PCM_WE_N
15 16
PCM_IRQA_N
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
TS1_VLD
TS1_CLK
PCM_A12 PCM_A7 PCM_A6 PCM_A5 PCM_A4
PCM_A3 PCM_A2
PCM_A1
PCM_A0 PCM_D0 PCM_D1
PCM_D2
+5V_PCMCIA
Close to CI SLOT
NC/10P
C287
DGND
FLASH
DGND
C320
0.1U
C321
2U2
3_3V
0.1U
C322
R325
10K
DGND
NAND-RBZ NAND-REZ NAND-CEZ
NAND-CLE NAND-ALE NAND-WEZ
NAND-WPZ
R326
NC/10K
U301
MT29F4G08AB
1
NC/RST
2
NC
3
NC1
4
NC2
5
NC3
6
R/B2
7
R/B1
8
RE
9
CE1
10
CE2
11
NC4
12
VCC
13
VSS
14
NC5
15
NC6
16
CLE
17
ALE
18
WE
19
WP
20
NC7
21
NC8
22
NC9
23
NC10
24 25
NC11 NC12
NC24 NC23 NC22 NC21
I/O7 I/O6 I/O5
I/O4 NC20 NC19
PRE VCC1 VSS1 NC18 NC17 NC16
I/O3 I/O2 I/O1
I/O0 NC15 NC14 NC13
48 47 46 45
NAND-D7 NAND_RBZ
44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26
NAND-D6 NAND-D5 NAND-D4
NC/0R
NAND-D3 NAND-D2
NAND-D1 NAND-D0
R324
3_3V
NAND-RBZ NAND-REZ
NAND-CEZ
NAND-CLE
NAND-ALE
NAND-WEZ
NAND-WPZ
NAND-D7 NAND-D6
NAND-D5 NAND-D4
0.1U
C323
NAND-D3 NAND-D2
NAND-D1
DGND
NAND-D0
R311 22R
R309 22R
R310 22R
R312 22R R313 22R R314 22R
R315
R316 22R
R317 22R
R318 22R R319 22R R320 22R R321 22R
R322 22R R323
NAND_WEZ
22R
NAND_WPZ
22R
NAND_REZ NAND_CEZ
NAND_CLE NAND_ALE
PCM_A7 PCM_A6 PCM_A5
PCM_A4 PCM_A3 PCM_A2 PCM_A1
PCM_A0
C325
33P
C324
33P
DGND
+5V_PCMCIA
1K
1K
R996
R997
PCM_CD1_N
PCM_CD2_N
10K
R998
10K
R999
CARD DETECT
PCM_CD_N
0.001U
C949
DGND
DGND
GND
GND
NC
NC
PCM_CD2_NPCM_CD1_N
GND
NC
GND
NC
PCM_CD_N
L 0V
H 2.5V
H 2.5V
H 2.5V
ZL
T
CN800
ZN
T
BR
LED Driver
+50VLED
BL_ON
DIM_PWM
1 2
R801
R804
R773
F81
3.15A
250VAC
!
680V
NTC81
T
1R5
300K
510K
510K
510K
R771
10K
R772 100K
GND
10K
!
V
VR81
8.2K 8.2K
PGND
!
R802
12V
R774 100K
300K
R805
R806
R807A
R807B
C7710.1U
NTC82
T
!
1R5
GND
PWMI
!
300K
C803
1000P
R770
C770
ISET
PWMI
C772
100P
!
CX82
0.22U
R803
R775 R776
C773
R81
1M2
R821M2
VCC1
C801
100R
EN
!
0.1U
PGND
1U
470K
!
!
2
R83
1M2
1
1M2
R84
!
C802
U770
13
VDD
FSW
8
1K
1U
FSW
15
COMP
3
GND1
6
ISET
GND
16
PWMI
9
EN
5 4
FB4 FB3
FSW
L81
!
FB
10N
GB98A
R779B
NC
43
R777
200R
CX81
!
0.47U
VCC
GATE
GND2
OVP
VCC
CS
FB1 FB2
CY81
GND
CY82
1
2
3
1000P
1000P
GND
FB
RT
12 11 10 14 7 1 2
R779A
100K
R778
!
!
U801
RT7736
L770
120UH
OVP
LED1 LED2
LED3LED4
6K8
2
VCC1
VCC
3
L82
GATE
VDD
ZVCC1
C805A
ZD770
C775
!
6
5
4
CS
T
10U 50V
10V
R780 22R
ISET
4
1
VCC1
PGND
1U
GND
R818
10R
C774100P
D81
RL255
D83
RL255
100P
C806
PGND
GND
1K
R781
BR
22V
ZD801
PGND
FR104
C805
10U 50V
A0D256
RL255
R814 470R
D802
D82
PGND
R782
10K
D84
RL255
0.33R
R783
GND
T
ZPGND
R817
Q802
BT3906
R815 22R
R812 10R
R813
B770
Q770
R784 0.33R
450V
C81
PGND
R788
10R
0.33R
R785
ZHV
T
68U
22R
B
HV
C82
E
C
10R
VAL?
0.33R
R786
450V
68U
FR207
AOTF11C60
Q801
R816
VS
330P
C777 330P
C776
GND
150K
150KR821A
R821B
10K
D770
150K
R821C
R821D150K
D801
R819A0.56
PGND
R790A
12K
R821E150K
R821F150K
R819B0.56
SB5200
GND
2200P
VAL?
B801
100PC807
12VOUT
R790BNC
C808
PGND
0R
R822
HV
HS1
1 2 3 4
R789
1M
VS
OVP
C778
0R R823
1000P
!
1
2
3
4
5
T801
C783
160V
22U
GND
N1
N4
N2
E1,E2
SCH SCH
PGND
C779 330P
VLED+
R791
220K
!
GND
CY83
NC
LED1
N3
330P
C780
FB
GND
R792220K
MBR10150
12
11
10
9
8
76
ZFB
T
R8240R
CN802
330P
C781
12VOUT
GND
4
3
PGND
1
1
2
D850A
C850
220P
+50VLED
T
ZPCGND
4 3 2 1
LED3LED2
R793220K
31
MBR10150
R83033R
R831
33R
PC820
TLP781
12V-1
T
12V
GND
T
GND-1
C782 330P
D850
R838
1K
MUR460 33R
33R
33R
2
D830
ZPC1
!
2
LED4
R794220K
R850
R851
R852
31
C830
1000P
T
1
T
ZPC2
R833
1K
TL431
U830
GND
100V
12V
32
LED1
LED2 LED3 LED4
47U
470U
25V
1
ZLED4
C851
C852
C831
R834
T
T
ZLED2
100V
25V
2K
ZLED3
C853A
0.1U
47U
470U
T
ZLED1
C853B0.1U
C832
0.1U
0.1U
12V
R798
R795 0R
R796 0R
R797
T
C833
25V
C835
C836
VLED+
0R
0R
VLED+
4.7K
4.7K
470U
ZLED+
T
R853A
R853B
NC
0.1U
C834
12V
R836
R835
10K
R837
1 2 3 4 5 6 7 8 9
10
MS08FP.SCH
33V
ZD850
33V
ZD851 Z12V
T
22K
6K8
CN701
V 1.0
+50VLED
12V
10K
ZGND
R832
T
R839
39K
T
Z50V
GND
GND
2.5V/2K=1.25mA
GND
GND
MS08FP
signal of main
1 Can not switch on
i
Check PW
Check reset
NO
Y
Check signal PON
DIMBL—ON of main IC link
Trouble shooting
no switch on
Check 3.3V/12V/24V of power supply
Only 3.3V
to PW
N
Check the peripheral circuit
of mail IC,check solder of
main IC,check data fo NVM
and reset it
Check crystal frequence
yes
Check DC-DC
part,check
Y
Check IIC bus
ndividual signal source
2abnormal picture
I
bad
Check the path with this
signal source
Abnormal picture
Check the peripheral circuit
of mail IC,updating SW,reset
NVM,replace main IC
Check crystal frequence
All signal source bad
Check panel ID
Check LVDS signal to main
ICcheck LVDS cable?
3 Abnormal sound
Individual sound
signal source
Check the sound signal
link to main IC
Check the peripheral
circuit of main IC,SW
Abnormal sound
N
Check the power of
Check the mute
sound IC
function
Check all sound
source
Check sound IC
N
Y
Check wave filter and
speaker
Y
Material:
ProjectDesigner:
Approve:
Mechanical
Part Name:
Scale:
Check:
Sheet:
Department
Weight(g):
Part Number:
Model Name:
>0~3

>3~6

>6~10

>10~14

>14~18

>18~24

>24~30







>800


>30~40 >40~50 >50~65 >65~80 >80~100>100~120>120~140

>140~160

>160~180

>180~200

>200~225

>225~250

>250~280

>280~315

>315~355

>355~400

>400~450

>450~500

>500~630

>630~800
Loading...