Taylor 441, 444 Operator's Manual

Download

Page 1

OPERATOR’S MANUAL

Model 441 & 444

Shake Freezers

Original Operating Instructions

029405- M

6/97 (Original Publication)

(Updated 7/1/15)

Page 2

Complete this page for quick reference when service is required:

Taylor Distributor: Address: Phone: Service: Parts: Date of Installation:

Information found on the data label:

Model Number: Serial Number: Electrical Specs: Voltage Cycle

Phase Maximum F use Size: A Minimum Wire Ampacity: A

E 1997 Carrier Commercial Refrigeration, Inc.

029405-M

Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work may be a violation of Copyright Law of the United States of America and other countries, could result in the awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further civil and criminal penalties. All rights reserved.

Taylor Company

a division of Carrier Commercial Refrigeration, Inc. 750 N. Blackhawk Blvd. Rockton, IL 61072

Page 3

Table of Contents

Section 1 To the Installer 1............................................

Section 2 To the Operator 4...........................................

Section 3 Safety 5....................................................

Section 4 Operator Parts Identification 7...............................

Model 441 7............................................................

Model 444 8............................................................

Models 441 & 444 Door Assembly 9.......................................

Accessories 10..........................................................

Section 5 Important: To the Operator 11.................................

Indicator Light “Mix Low” 11...............................................

Symbol Definitions 11....................................................

Control Switch 11........................................................

Reset Button 11.........................................................

Thermistor Control 12....................................................

Separate Hopper Refrigeration System (SHR) 12............................

Section 6 Operating Procedures 13.....................................

Assembly 13............................................................

Sanitizing 16............................................................

Priming 17..............................................................

Closing Procedure 18....................................................

Draining Product From the Freezing Cylinder 18.............................

Rinsing 19..............................................................

Cleaning 19.............................................................

Disassembly 19..........................................................

Brush Cleaning 19.......................................................

Section 7 Important: Operator Checklist 21..............................

During Cleaning and Sanitizing 21.........................................

Troubleshooting Bacterial Count 21........................................

Regular Maintenance Checks 22...........................................

Winter Storage 22........................................................

Table of Contents Models 441 & 444

Page 4

Table of Contents - Page 2

Section 8 Troubleshooting Guide 23....................................

Section 9 Parts Replacement Schedule 26...............................

Section 10 Limited Warranty on Equipment 27............................

Section 11 Limited Warranty on Parts 29.................................

Note: Continuing research results in steady improvements; therefore, info rmation in this manual is subject to change without notice.

Note: Only instructions originating from the factory or its authorized translation representative(s) are considered to be the original set of instructions.

E 1997 Carrier Commercial Refrigeration, Inc. (Original Publication)

(Updated July, 2015) 029405- M Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work may be a violation of Copyright Law of the United States of America and other countries, could result in the awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further civil and criminal penalties. All rights reserved.

Models 441 & 444

Taylor Company

a division of Carrier Commercial Refrigeration, Inc. 750 N. Blackhawk Blvd. Rockton, IL 61072

Table of Contents

Page 5

Section 1 To the Installer

The following information has been included in the manual as safety and regulatory guidelines. For complete installation instructions, please see the Installation Checklist.

Installer Safety

In all areas of the world, equipment should be installed in accordance with existing local codes. Please contact your local authorities if you have any questions.

Care should be taken to ensure that all basic safety practices are followed during the installation and servicing activities related to the installation and service of Taylor equipment.

S Only authorized Taylor service personnel

should perform installation and repairs on the equipment.

S Authorized service personnel should consult

OSHA Standard 29CFRI910.147 or the applicable code of the local area for the industry standards on lockout/tagout procedures before beginning any installation or repairs.

S Authorized service personnel must ensure

that the proper PPE is available and worn when required during installation and service.

S Authorized service personnel must remove all

metal jewelry, rings, and watches before working on electrical equipment.

The main power supply(s) to the freezer must be disconnected prior to performing any repairs. Failure to follow this instruction may result in personal injury or death from electrical shock or hazardous moving parts as well as poor performance or damage to the equipment.

Site Preparation

Review the area where the unit will be installed before uncrating the unit. Make sure all possible hazards to the user or the equipment have been addressed.

For Indoor Use Only: This unit is designed to operate indoors, under normal ambient temperatures of

70°-75°F(21°-24°C). The unit has successfully

performed in high ambient temperatures of up to

104°F(40°C) at reduced capacities.

This unit must NOT be installed in an area where a water jet or hose can be used. NEVER use a water jet or hose to rinse or clean the unit. Failure to follow this instruction may result in electrocution.

This unit must be installed on a level surface to avoid the hazard of tipping. Extreme care should be taken in moving this equipment for any reason. Two or more persons are required to safely move this unit. Failure to comply may result in personal injury or equipment damage.

Uncrate the unit and inspect it for damage. Report any damage to your Taylor Distributor.

This piece of equipment is made in the USA and has USA sizes of hardware. All metric conversions are approximate and vary in size.

Air Cooled Units

DO NOT obstruct air intake and discharge openings:

Note:Allrepairsmustbeperformedbyan authorized Taylor Service Technician.

This unit has many sharp edges that can

cause severe injuries.

Models 441 & 444 To the Installer

Air cooled units require a minimum of 3” (76 mm) of clearance around all sides of the freezer to allow for adequate air flow across the condensers. Install the deflector provided to prevent recirculation of warm air. Failure to allow adequate clearance can reduce the refrigeration capacity of the freezer and possibly cause permanent damage to the compressor.

131206

Page 6

Water Connections

(Water Cooled Units Only)

An adequate cold water supply must be provided with a hand shut- off valve. On the underside rear of the base pan, two 3/8” I.P.S. (for single head units) or two 1/2” I.P.S. (for double head units) water connections for inlet and outlet have been provided for easy hook- up. 1/2” inside diameter water lines should be connected to the machine. (Flexible lines are recommended, if local codes permit.) Depending on local water conditions, it may be advisable to install a water strainer to prevent foreign substances from clogging the automatic water valve. There will be only one water “in” and one water “out” connection for both single head and double head units. DO NOT install a hand shut- off valve on the water “out” line! Water should always flow in this order: first, through the automatic water valve; second, through the condenser; and third, through the outlet fitting to an

opentrapdrain.

A back flow prevention device is required

on the incoming water connection side. Please

refer to the applicable National, State, and local codes for determining the proper configuration.

Electrical Connections

In the United States, this equipment is intended to be installed in accordance with the National Electrical Code (NEC), ANSI/NFPA 70-1987. The purpose of the NEC code is the practical safeguarding of persons and property from hazards arising from the use of electricity. This code contains provisions considered necessary for safety. In all other areas of the world, equipment should be installed in accordance with the existing local codes. Please contact your local authorities.

Each unit requires one power supply for each data label on the unit. Check the data label(s) on the freezer for branch circuit overcurrent protection or fuse, circuit ampacity, and other electrical specifications. Refer to the wiring diagram provided inside of the electrical box for proper power connections.

FOLLOW YOUR LOCAL ELECTRICAL CODES!

CAUTION: THIS EQUIPMENT MUST BE PROPERLY GROUNDED! FAILURE TO DO SO CAN RESULT IN SEVERE PERSONAL INJURY FROM ELECTRICAL SHOCK!

This unit is provided with an equipotential grounding lug that is to be properly attached to the rear of the frame by the authorized installer. The installation location is marked by the equipotential bonding symbol (5021 of IEC 60417-1) on both the removable panel and the equipment’s frame.

S Stationary appliances which are not equipped

with a power cord and a plug or another device to disconnect the appliance from the power source must have an all-pole disconnecting device with a contact gap of at least 3 mm installed in the external installation.

S Appliances that are permanently connected to

fixed wiring and for which leakage currents may exceed 10 mA, particularly when disconnected or not used for long periods, or during initial installation, shall have protective devices such as a GFI, to protect against the leakage of current, installed by the authorized personnel to the local codes.

S Supply cords used with this unit shall be

oil-resistant, sheathed flexible cable not lighter than ordinary polychloroprene or other equivalent synthetic elastomer-sheathed cord (Code designation 60245 IEC 57) installed with the proper cord anchorage to relieve conductors from strain, including twisting, at the terminals and protect the insulation of the conductors from abrasion.

If the supply cord is damaged, it must be replaced by an authorized Taylor service technician in order to avoid a hazard.

130909

To the Installer

Models 441 & 444

Page 7

Check Out

Once the unit is installed, it is advisable to check the following controls and mechanical operations of the freezer and to make any necessary adjustments. If applicable, repeat these checks for the second freezing cylinder on double head units.

Controls

Place the control switch in the “AUTO” position. The main refrigeration system will operate (compressor, beater motor , and the condenser fan). The dial light and the mix low indicator will be illuminated.

Refrigerant

In consideration of our environment, Taylor uses only earth friendly HFC refrigerants. The HFC refrigerant used in this unit is R404A. This refrigerant is generally considered non-toxic and non-flammable, with an Ozone Depleting Potential (ODP) of zero (0).

However, any gas under pressure is potentially hazardous and must be handled with caution.

NEVER fill any refrigerant cylinder completely with liquid. Filling the cylinder to approximately 80% will allow for normal expansion.

Use only R404A refrigerant that conforms to the AHRI standard 700 specification. The use of any other refrigerant may expose users and operators to unexpected safety hazards.

Figure 1

If the freezer is water cooled, the automatic water valve will begin to open and cold water will flow into the condenser. This will remove heat from the refrigerant. As the water flows into the open trap drain, it should be warm to the touch. Place the control switch in the “OFF” position.

Beater Rotation

Beater rotation must be clockwise as viewed

looking into the freezing cylinder.

Note: The following procedures must be performed by an authorized Taylor service technician.

To correct rotation on a three- phase unit, interchange any two incoming power supply lines at the freezer main terminal block only. To correct rotation on a single- phase unit, exchange leads inside the beater motor. (Follow the diagram printed on the motor.)

Electrical connections are made directly to the terminal block provided in the main control box located behind the service panel.

Refrigerant liquid sprayed onto the skin may cause serious damage to tissue. Keep eyes and skin protected. If refrigerant burns should occur, flush immediately with cold water. If burns are severe, apply ice packs and contact a physician immediately.

Taylor reminds technicians to be cautious of government laws regarding refrigerant recovery, recycling, and reclaiming systems. If you have any questions regarding these laws, please contact the factory Service Department.

WARNING: R404A refrigerant used in conjunction with polyolester oils is extremely moisture absorbent. When opening a refrigeration system, the maximum time the system is open must not exceed 15 minutes. Cap all open tubing to prevent humid air or water from being absorbed by the oil.

130909

Models 441 & 444 To the Installer

Page 8

Section 2 To the Operator

The freezer you have purchased has been carefully engineered and manufactured to give you dependable operation. The Taylor freezer, when properly operated and cared for, will produce a consistent quality product. Like all mechanical products, this machine will require cleaning and maintenance. A minimum amount of care and attention is necessary if the operating procedures outlined in this manual are followed closely.

This Operator’s Manual should be read before operating or performing any maintenance on your equipment.

Your Taylor freezer will NOT eventually compensate and correct for any errors during the set- up or filling operations. Thus, the initial assembly and priming procedures are of extreme importance. It is strongly recommended that all personnel responsible for the equipment’s operation review these procedures in order to be properly trained and to make sure that there is no confusion.

In the event that you should require technical assistance, please contact your local authorized Taylor Distributor.

Note: Your Taylor warranty is valid only if the parts are authorized Taylor parts, purchased from the local authorized Taylor Distributor, and only if all required service work is provided by an authorized Taylor service technician. Taylor reserves the right to deny warranty claims on units or parts if non- Taylor approved parts or incorrect refrigerant were installed in the unit, system modifications were performed beyond factory recommendations, or it is determined that the failure was caused by abuse, misuse, neglect, or failure to follow all operating instructions. For full details of your Taylor Warranty, please see the Limited Warranty section in this manual.

Note: Constant research results in steady improvements; therefore, information in this manual is subject to change without notice.

If the crossed out wheeled bin symbol is affixed to this product, it signifies that this product is compliant with the EU Directive as well as other similar legislation in effect after August 13, 2005. Therefore, it must be collected separately after its use is

completed, and cannot be disposed as unsorted municipal waste.

The user is responsible for returning the product to the appropriate collection facility, as specified by your local code.

For additional information regarding applicable local laws, please contact the municipal facility and/or local distributor.

Compressor Warranty Disclaimer

The refrigeration compressor(s) on this unit are warranted for the term stated in the Limited Warranty section in this manual. However, due to the Montreal Protocol and the U.S. Clean Air Act Amendments of 1990, many new refrigerants are being tested and developed, thus seeking their way into the service industry. Some of these new refrigerants are being advertised as drop- in replacements for numerous applications. It should be noted that in the event of ordinary service to this unit’s refrigeration system,

only the refrigerant specified on the affixed data label should be used. The unauthorized use of

alternate refrigerants will void your Taylor compressor warranty. It is the unit owner’s responsibility to make this fact known to any technician he employs.

It should also be noted that Taylor does not warrant the refrigerant used in its equipment. For example, if the refrigerant is lost during the course of ordinary service to this machine, Taylor has no obligation to either supply or provide its replacement either at billable or unbillable terms. Taylor does have the obligation to recommend a suitable replacement if the original refrigerant is banned, obsoleted, or no longer available during the five year warranty of the compressor.

Taylor will continue to monitor the industry and test new alternates as they are being developed. Should a new alternate prove, through our testing, that it would be accepted as a drop- in replacement, then the above disclaimer would become null and void. To find out the current status of an alternate refrigerant as it relates to your compressor warranty , call the local Taylor Distributor or the Taylor Factory. Be prepared to provide the Model/Serial Number of the unit in question.

131206

To the Operator

Models 441 & 444

Page 9

Section 3 Safety

We, at T aylor Company, are concerned about the safety of the operator at all times when they are coming in contact with the unit and its parts. Taylor makes every effort to design and manufacture built- in safety features to protect both operators and service technicians.

Installing and servicing refrigeration equipment can be hazardous due to system pressure and electrical components. Only trained and qualified service personnel should install, repair, or service refrigeration equipment. When working on refrigeration equipment, observe precautions noted in the literature, tags and labels attached to the unit, and other safety precautions that may apply. Follow all safety code requirements. Wear safety glasses and work gloves.

IMPORTANT - Failure to adhere to the following safety precautions may result in severe personal injury or death. Failure to comply with these warnings may damage the machine and its components. Component damage will result in part replacement expense and service repair expense.

DO NOT operate the freezer without reading

this Operator Manual. Failure to follow this instruction may result in equipment damage, poor freezer performance, health hazards, or personal injury.

This appliance is to be used only by trained personnel. It is not intended for use by children or people with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

S DO NOT operate the freezer unless it is

properly grounded.

S DO NOT operate the freezer with larger fuses

than specified on the freezer data label.

S All repairs must be performed by an

authorized Taylor service technician.

S The main power supplies to the machine must

be disconnected prior to performing any repairs.

S For Cord Connected Units: Only Taylor

authorized service technicians or licensed electricians may install a plug or replacement cord on these units.

S Stationary appliances which are not equipped

S Appliances that are permanently connected to

S Supply cords used with this unit shall be

If the supply cord is damaged, it must be

Models 441 & 444 Safety

Failure to follow these instructions may result in electrocution. Contact your local authorized Taylor Distributor for service.

replaced by an authorized Taylor service technician in order to avoid a hazard.

130909

Page 10

DO NOT use a water jet to clean or rinse the freezer. Failure to follow these instructions may result in serious electrical shock.

Access to the service area of the unit must be restricted to persons having knowledge and practical experience with the unit, in particular as far as safety and hygiene are concerned.

S DO NOT allow untrained personnel to operate

this machine.

S DO NOT operate the freezer unless all service

panels and access doors are restrained with screws.

S DO NOT remove any internal operating parts

(examples: freezer door, beater, scraper blades, etc.) unless all control switches are in

the OFF position. Failure to follow these instructions may result in severe personal injury to fingers or hands from hazardous moving parts.

This unit has many sharp edges that can

cause severe injuries.

S DO NOT put objects or fingers in the door

spout. This may contaminate the product and

cause severe personal injury from blade

contact.

S USE EXTREME CAUTION when removing

the beater asssembly. The scraper blades are

very sharp.

Cleaning and sanitizing schedules are governed by your state or local regulatory agencies and must be followed accordingly. Please refer to the cleaning section of this manual for the proper procedure to clean this unit.

This unit is designed to maintain product temperature under 41_F(5_C). Any product being added to this unit must be below 41_F(5_C). Failure to follow this instruction may result in health hazards and poor freezer performance.

DO NOT obstruct air intake and discharge openings: A minimum of 3” (76 mm) air space is required around

all sides of the unit. Install the deflector provided to prevent recirculation of warm air. Failure to follow this instruction may cause poor freezer performance and damage to the machine.

For Indoor Use Only: This unit is designed to operate indoors, under normal ambient temperatures of

70°-75°F(21°-24°C). The unit has successfully

performed in high ambient temperatures of up to

104°F(40°C) at reduced capacities.

DO NOT run the unit without product. Failure to follow this instruction can result in damage to the unit.

This freezer must be placed on a level surface. Failure to comply may result in personal injury or equipment damage.

130909

Safety

NOISE LEVEL: Airborne noise emission does not

exceed 78 dB(A) when measured at a distance of 1.0 meter from the surface of the machine and at a height of 1.6 meters from the floor.

Models 441 & 444

Page 11

Section 4 Operator Parts Identification

Model 441

Item Description Part No.

1 Cover A.- Hopper- Standard X38458

1a Knob- Hopper Cover 025429

2 Gasket- Hopper Cover- 20 Qt. 038375

3 Pan- Drip - 11- 5/8 Long 027503

4 Tube- Feed- SS 028967- 7

5 Panel- Rear 013637

6 Panel- Side- Upper Right 028707- SP

7 Panel A.- Side Lower Left X44853

8 Caster- Swivel- 5/8 Stem 4” Wheel 018794

9 Panel- Side Upper Left 028700

Models 441 & 444 Operator Parts Identification

Item Description Part No.

10 Shield- Splash 15” x 5- 13/32 022763

11 Tray- Drip 14- 7/8 x 5- 1/8 013690

12 Caster- 4” Swv 5/8 Stem w/Brake 034081

13 Panel- Service 049613

14 Panel A.- Front X49600

15 Louver- Side R & L 017471

16 Stud- Nose 022822

17 Adaptor A.- Caster X18915

18 Panel A.- Side Lower Right X44855

111101

Page 12

Model 444

Item Description Part No.

1 Cover A.- Hopper- Insulated X39291

1a Knob- Hopper Cover 025429

2 Stud- Nose Cone 022822

3 Pan- Drip 11- 5/8 Long 027503

4 Tube- Feed- SS 028967- 7

5 Louver- Side Left & Right 017471

6 Panel- Upper Side Right 028701

7 Caster- 4 ” Swv 5/8 Stem w/Brake 034081

8 Panel- Service 024439

111101

Operator Parts Identification

Item Description Part No.

9 Panel- Upper Side Left 028700

10 Shield- Splash 037041

11 Tray- Drip 014533

12 Panel- Rear 017563

13 Panel A.- Front X14239

14 Panel A.- Side Right X44855

15 Panel A.- Side Left X44853

16 Adaptor A.- Caster X18915

17 Caster- Swivel- 5/8 Stem 4” Wheel 018794

Models 441 & 444

Page 13

Models 441 & 444 Door Assembly

Item Description Part No.

1 Seal- Drive Shaft 032560

2 Shaft- Beater 033498

3 Beater A.- 7 Qt.- 1 Pin Support X46233

4 Bearing- Front 013116

5 Gasket- Door 5.177 ID x 5.9380 016672

6 Decal- Lift Plate Front 015200

7 Valv e A.- D raw X13624- SP

Models 441 & 444 Operator Parts Identification

Item Description Part No.

8 O- Ring 1 - 1/16 OD x .139 W 020571

9 Door A.- 1 Spout 7 Qt. X30272- SER

10 Nut- Stud 021508

11 Clip- Scraper Blade - 8.75 Inch 046238

12 Blade- Scraper- Plastic 046237

Page 14

Accessories

Item Description Part No.

1 Pail- 10 Qt. 013163

2 Brush- Mix Pump Body 3 x 7 023316

3 Brush- Double Ended 013072

4 Brush- Rear Bearing 013071

5 Brush- Draw Valve 014753

140811

Operator Parts Identification

Item Description Part No.

Kit A.- Tune Up (Model 441) X33351

Kit A.- Tune Up (Model 444) X36356

7 Lubricant- Taylor 047518

8 Sanitizer- Kay- 5 125 Packets 041082

Models 441 & 444

Page 15

Section 5 Important: To the Operator

Indicator Light “Mix Low”

The Models 441 and 444 are equipped with a “MIX LOW” light located on the front of the machine. When the light begins to flash, it indicates that the mix hopper has a low supply of mix and should be refilled as soon as possible. Always maintain at least 3” (76 mm) of mix in the hopper to allow the mix feed assembly to operate properly. If you neglect to add mix when the light begins to flash, a freeze- up may occur, causing eventual damage to the beater, blades, drive shaft, and freezer door.

Figure 2

Symbol Definitions

Control Switch

The center position is “OFF”. The right position is “AUTO”, which activates the beater motor and the refrigeration system. The left position is “WASH” which activates the beater motor only .

Figure 3

Reset Button

On the Models 441 and 444, the reset button is located on the lower front panel.

The reset button protects the beater motor from an overload condition. If an overload occurs, the reset mechanism will trip. To properly reset the freezer, place the control switch in the “OFF” position. Press the reset button firmly. Place the control switch in the “WASH” position and observe the freezer’s performance. Once satisfied, place the control switch back in the “AUTO” position.

The following chart identifies the symbol definitions used on the operator switches.

= The “WASH” position.

= The “OFF” position.

= The “ON/AUTO” position.

Models 441 & 444 Important: To the Operator

Figure 4

Page 16

Thermistor Control

The viscosity (thickness) of the product is controlled by a temperature sensing device called the thermistor. To achieve a thicker product, turn the control clockwise, and turn the control counterclockwise to achieve a thinner product. Allow the refrigeration system to cycle on and off 2 or 3 times before an accurate consistency can be evaluated.

Separate Hopper Refrigeration System (SHR)

The Separate Hopper Refrigeration System (SHR) is a standard feature. The SHR incorporates the use of a separate small refrigeration system to maintain the mix temperature in the hopper to below 40_F. ( 4 . 4_C.) This assures bacteria control.

Important: To the Operator

Models 441 & 444

Page 17

Section 6 Operating Procedures

The Model 441 has been selected to show you the pictured step- by- step operating procedures for both models contained in this manual. These models, for practical purposes of operation, are the same.

They both store 20 quarts (18.9 liters) of mix in the hopper. The mix then flows by gravity through a mix feed tube down into the freezing cylinder.

Locate your model number below to determine the characteristics of your freezer:

441: (1) 7 quart (6.6 liter) freezing cylinder. 444: (2) 7 quart (6.6 liter) freezing cylinders. We begin our instructions at the point where we enter

the store in the morning and find the parts disassembled and laid out to air dry from the previous night’s cleaning.

The following procedures will show you how to assemble the parts into the freezer, sanitize them, and prime the freezer with fresh mix in preparation to serve your first portion.

If you are disassembling the machine for the first time or need information to get to this starting point in our instructions, turn to page 19, “Disassembly” and start there.

Step 2

Insert the drive shaft through the rear shell bearing in the freezing cylinder and engage the hex end firmly into the gear box coupling.

Figure 5

Assembly

MAKE SURE THE CONTROL SWITCH IS IN THE “OFF” POSITION TO ELIMINATE THE CHANCE OF MOVING PARTS.

Note: When lubricating parts, use an approved food

grade lubricant (example: Taylor Lube).

Step 1

Lubricate the groove and shaft portion that comes in contact with the bearing on the beater drive shaft. Slide the seal over the shaft and groove until it fits into place. DO NOT lubricate the hex end of the driveshaft. Fillthe inside portion of the seal with 1/4” more lubricant and evenly lubricate the flat side of the seal that comes in contact with the bearing.

Figure 6

USE EXTREME CAUTION when handling the beater assembly. The scraper blades are very sharp and may cause injury.

050323

Models 441 & 444 Operating Procedures

Page 18

Step 3

Before installing the beater assembly , check the scraper blades for any signs of wear or damage. If a scraper blade is nicked or worn, replace both blades.

Check the scraper blade clips to make sure they are not bent and the slot is even for the entire length of the clip. Replace any damaged clips.

Figure 7

Step 5

Holding the rear blade on the beater, slide the assembly halfway into the freezing cylinder. Install the front scraper blade over the front holding pin. Slide the beater assembly the rest of the way into the freezing cylinder.

Figure 9

Make sure the beater assembly is in position over the drive shaft. Turn the beater slightly to be certain that the beater is properly seated. When in position, the beater will not protrude beyond the front of the freezing cylinder.

Step 4

If the blades and clips are in good condition, place the rear scraper blade over the rear holding pin on the beater, knife edge to the outside.

Figure 8

Note: To prevent costly damage, the hole in the scraper blade must fit securely over the pin.

Step 6

Before assembling the freezer door, check the following for any nicks, cracks, or signs of wear: front bearing, door gasket, draw valve, o- rings, and all sides of the door assembly, including the inside of the draw valve bore. Replace any damaged parts.

Step 7

Slide the two o- rings into the grooves on the draw valve and lubricate them with Taylor Lube.

Figure 10

150701

Operating Procedures

Models 441 & 444

Page 19

Step 8

Lubricate the inside of the freezer door spout, top and bottom. Insert the draw valve into the freezer door from the top. It will be necessary to rotate the draw valve to the right when assembling the door to the freezer.

Figure 11

Step 9

Place the freezer door gasket into the groove on the back of the freezer door. Slide the front bearing over the baffle rod so the flanged edge is against the door.

Do not lubricate the gasket or bearing.

Step 10

Insert the baffle rod through the beater in the freezing cylinder. With the door seated on the freezer studs, install the handscrews. Tighten equally in a crisscross pattern to insure that the door is snug.

Figure 13

Step 11

Rotate the draw valve bracket to the left. Center it into position by raising the draw arm and placing it into the slotted groove of the draw valve bracket.

Figure 14

Step 12

Lay the mix feed tube and the hopper gasket in the bottom of the mix hopper.

Note: Hopper gaskets are not used on the Model 444.

Repeat Steps 1 through 12 for the other side of the

Figure 12

Models 441 & 444 Operating Procedures

freezer on the Model 444.

Page 20

Step 13

Install the front drip tray and splash shield under the door spout(s).

Figure 15

Step 14

Slide the rear drip pan into the hole(s) in the side panel.

Step 3

While the solution is flowing into the freezing cylinder, brush clean the hopper.While cleaning the mix hopper, take particular care in brushing the mix level sensing probe on the rear wall of the hopper, the mix inlet hole, the hopper gasket, and the mix feed tube.

Sanitizing

Step 1

Prepare a pail of approved 100 PPM sanitizing solution (examples: 2- 1/2 gal. [9.5 liters] of Kay- 5R or 2 gal. [7.6 liters] of Stera- SheenR). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS.

Step 2

Pour the sanitizing solution into the hopper and allow it to flow into the freezing cylinder.

Figure 16

Figure 17

Step 4

Place the control switch in the “WASH” position. This will cause the sanitizing solution in the freezing cylinder to agitate. Allow the solution to agitate for five minutes.

Figure 18

080924

Operating Procedures

Models 441 & 444

Page 21

Step 5

Place an empty pail beneath the door spout and raise the draw arm. Draw off all the sanitizing solution.

Figure 19

Step 6

When the sanitizer stops flowing from the door spout, lower the draw arm and place the control switch in the “OFF” position.

IMPORTANT! The unit must NOT be placed in AUTO until all sanitizing solution has been removed from the freezing cylinder and proper priming procedures have been completed. Failure to follow this instruction may result in damage to the freezing cylinder.

Note: You have just sanitized the freezer; therefore, be sure your hands are sanitized before continuing these instructions.

Step 7

Stand the mix feed tube in the corner of the mix hopper, and assemble the hopper gasket.

Priming

Prime the machine as close to the time of first product draw as possible.

Step 1

Place a pail beneath the door spout and raise the draw arm. Pour two gallons (7.6 liters) of fresh mix into the hopper and allow it to flow down into the freezing cylinder. This will force out any remaining sanitizing solution.

Figure 21

Step 2

When full strength mix is flowing from the door spout, lower the draw arm.

IMPORTANT! Failure to remove all sanitizing solution may result in damage to the freezing cylinder.

Step 3

When the mix has stopped bubbling down into the freezing cylinder, install the mix feed tube into the mix inlet hole.

Figure 20

Repeat Steps 1 through 7 for the other side of the freezer on the Model 444.

Models 441 & 444 Operating Procedures

Figure 22

150701

Page 22

Step 4

Place the control switch in the “AUTO” position. When the unit cycles off, the product will be at serving temperature.

Figure 23

Step 5

Fill the hopper with mix. As the mix level comes in contact with the mix level sensing probe on the rear wall of the hopper, the “MIX LOW” light will extinguish.

Note: Always maintain at least 3” (76 mm) of mix in the hopper to allow the mix feed assembly to operate properly.

Step 6

Place the mix hopper cover in position.

Closing Procedure

To disassemble your unit, the following items will be needed:

S Two cleaning pails S Sanitized stainless steel rerun can with lid S Necessary brushes (provided with freezer) S Cleaner S Single service towels

Draining Product From the Freezing Cylinder

Step 1

Place the control switch in the “OFF” position.

Step 2

Remove the hopper cover, the hopper gasket, and the mix feed tube. Take these parts to the sink for cleaning.

Step 3 If local health codes permit the use of rerun,place

a sanitized, NSF approved stainless steel rerun container beneath the door spout. Place the control switch in the “WASH” position and raise the draw arm. When all the product stops flowing from the door spout, lower the draw arm and place the control switch in the “OFF” position. Place the sanitized lid on the rerun container and place it in the walk- in cooler.

Figure 24

Repeat Steps 1 through 5 for the other side of the freezer on the Model 444.

140811

Operating Procedures

Note: If local health codes DO NOT permit the use of rerun, the product must be discarded. Follow the

instructions in the previous step, except drain the product into a pail and properly discard the mix.

Repeat these steps for the second freezing cylinder on the Model 444.

ALWAYS FOLLOW LOCAL HEALTH CODES.

Models 441 & 444

Page 23

Rinsing

Disassembly

Step 1

Pour two gallons (7.6 liters) of cool, clean water into the mix hopper. With the brushes provided, scrub the mix hopper, the mix inlet hole, and the mix level sensing probe.

Step 2

With a pail beneath the door spout, place the control switch in the “WASH” position and raise the draw arm. Drain all the rinse water from the freezing cylinder. When the rinse water stops flowing from the door spout, lower the draw arm and place the control switch in the “OFF” position.

Repeat this procedure until the rinse water being drawn from the freezing cylinder is clear.

Repeat these steps for the second freezing cylinder on the Model 444.

Cleaning

Step 1

Prepare a pail of approved 100 PPM cleaning solution (examples: 2- 1/2 gal. [9.5 liters] of Kay- 5R or 2 gal. [7.6 liters] of Stera- SheenR). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS.

Note: Failure to remove parts, brush clean and then air dry these parts, will result in damage to the related parts.

Step 1

BE SURE THE CONTROL SWITCH IS IN THE “OFF” POSITION TO ELIMINATE THE CHANCE OF MOVING PARTS.

Step 2

Remove the handscrews, the freezer door, the gasket, the front bearing, the beater, the scraper blade(s), and the drive shaft from the freezing cylinder. Take these parts to the sink for cleaning.

Step 3

Remove the rear drip pan from the side panel.

Note: If the drip pan is filled with an excessive amount of mix, it is an indication that the drive shaft seal should be replaced or was improperly lubricated.

Repeat these steps for the second freezing cylinder on the Model 444.

Step 4

Remove the front drip tray and the splash shield.

Step 2

Pour the cleaning solution into the hopper and allow it to flow into the freezing cylinder.

Step 3

While the solution is flowing into the freezing cylinder, brush clean the mix hopper, the mix inlet hole, and the mix level sensing probe.

Step 4

Place the control switch in the “WASH” position. This will cause the cleaning solution in the freezing cylinder to agitate.

Step 5

Place an empty pail beneath the door spout and raise the draw arm. Draw off all the cleaning solution. When the solution stops flowing from the door spout, lower the draw arm and place the control switch in the “OFF” position.

Repeat Steps 1 through 5 for the second freezing cylinder on the Model 444.

Models 441 & 444 Operating Procedures

Brush Cleaning

Step 1

Prepare a sink with an approved cleaning solution (examples: Kay- 5R or Stera- SheenR). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS.

If an approved cleaner other than Kay- 5R or Stera- SheenR is used, dilute it according to the label instructions. IMPORTANT: Follow the label directions. Too STRONG of a solution can cause parts damage. Too MILD of a solution will not provide adequate cleaning. Make sure all brushes provided with the freezer are available for brush cleaning.

Step 2

Remove the seal(s) from the drive shaft(s).

080924

Page 24

Step 3

From the freezer door(s) remove:

S the gasket(s) S the front bearing(s) S the draw valve(s)

Remove all o- rings.

Note: To remove o- rings, use a single service towel to grasp the o- ring. Apply pressure in an upward direction until the o- ring pops out of its groove. With the other hand, push the top of the o- ring forward. It will roll out of the groove and can be easily removed. If there is more than one o- ring to be removed, always remove the rear o- ring first. This will allow the o- ring to slide over the forward rings without falling into the open grooves.

Step 4

Thoroughly brush clean all disassembled parts in the cleaning solution, making sure all lubricant and mix film is removed. Take particular care to brush clean the draw valve core in the freezer door(s). Place all the cleaned parts on a clean dry surface to air dry overnight.

Step 5

Return to the freezer with a small amount of cleaning solution. With the black bristle brush, brush clean the rear shell bearing(s) at the back of the freezing cylinder(s).

Figure 25

Step 6

Wipe clean all exterior surfaces of the freezer.

Operating Procedures

Models 441 & 444

Page 25

Section 7 Important: Operator Checklist

During Cleaning and Sanitizing

j 4. Use the black bristle brush to thoroughly clean

ALWAYS FOLLOW LOCAL HEALTH CODES.

Cleaning and sanitizing schedules are governed by federal, state, or local regulatory agencies, and must be followed accordingly. If the unit has a “Standby mode”, it must not be used in lieu of proper cleaning and sanitizing procedures and frequencies set forth by the ruling health authority. The following check points should be stressed during the cleaning and sanitizing operations.

the rear shell bearing located at the rear of the freezing cylinder. Be sure there is a generous amount of cleaning solution on the brush.

j 5. IF LOCAL HEALTH CODES PERMIT THE

USE OF RERUN, make sure the mix rerun is stored in a sanitized, covered stainless steel container and is used the following day. DO NOT prime the machine with rerun. When using rerun, skim off the foam and discard, then mix the rerun with fresh mix in a ratio of 50/50 during the day’s operation.

CLEANING AND SANITIZING MUST BE

PERFORMED DAILY.

T roubleshooting Bacterial Count

j 1. Thoroughly clean and sanitize the machine

regularly, including complete disassembly and brush cleaning.

j 2. Use all brushes supplied for thorough cleaning.

The brushes are specially designed to reach all mix passageways.

j 3. Use the white bristle brush to clean the mix inlet

hole which extends from the mix hopper down to the rear of the freezing cylinder.

j 6. On a designated day of the week, run the mix as

low as feasible and discard after closing. This will break the rerun cycle and reduce the possibility of high bacteria and coliform counts.

j 7. Properly prepare the cleaning and sanitizing

solutions. Read and follow label directions carefully. Too strong of a solution may damage the parts and too weak of a solution will not do an adequate job of cleaning or sanitizing.

j 8. The temperature of the mix in the mix hopper

and walk- in cooler should be below 40_F. (4.4_C.).

080401

Models 441 & 444 Important: Operator Checklist

Page 26

Regular Maintenance Checks

Winter Storage

j 1. Rotate scraper blades to allow both sides of the

knife edge to wear evenly. This will contribute to self- sharpening and help maintain fast, efficient freezing.

j 2. Replace scraper blades that are nicked,

damaged or worn.

j 3. Before installing the beater, be certain that

scraper blades are properly attached over the pins.

j 4. Check the rear shell bearing for signs of wear

(excessive mix leakage in rear drip pan) and be certain it is properly cleaned.

j 5. Using a screwdriver and cloth towel, keep the

rear shell bearing and the female hex drive socket clean and free of lubricant and mix deposits.

j 6. Dispose of o- rings and seals if they are worn,

torn, or fit too loosely, and replace with new ones.

j 7. Follow all lubricating procedures as outlined in

“Assembly”.

j 8. Check the condensers for accumulation of dirt

and lint. Dirty condensers will reduce the efficiency and capacity of the machine. Condensers should be cleaned monthly with a soft brush. Never use screwdrivers or other metal probes to clean between the fins. Note: For machines equipped with an air filter, it will be necessary to vacuum clean the filters on a monthly schedule.

j 9. On water cooled units, check the water lines for

kinks or leaks. Kinks can occur when the machine is moved back and forth for cleaning or maintenance purposes. Deteriorated or cracked water lines should be replaced only by an authorized Taylor technician.

If the place of business is to be closed during the winter months, it is important to protect the freezer by following certain precautions, particularly if the building is subject to freezing conditions.

Disconnect the freezer from the main power source to prevent possible electrical damage.

On water cooled freezers, disconnect the water supply. Relieve pressure on the spring in the water valve. Use air pressure on the outlet side to blow out any water remaining in the condenser. This is extremely important. Failure to follow this procedure may cause severe and costly damage to the refrigeration system.

Your local Taylor Distributor can perform this service for you.

Wrap detachable parts of the freezer such as the beater, blades, drive shaft, and freezer door . Place these parts in a protected, dry place. Rubber trim parts and gaskets can be protected by wrapping them with moisture- proof paper. All parts should be thoroughly cleaned of dried mix or lubrication which attract mice and other vermin.

080401

Important: Operator Checklist

Models 441 & 444

Page 27

Section 8 Troubleshooting Guide

PROBLEM PROBABLE CAUSE REMEDY PAG E

REF.

1. No product being dispensed with the draw valve open and the control switch in AUTO.

2. The product is too cold. a. The thermistor control is

3. The product appears too thin.

a. The freezer door is

installed upside down.

b. There is a freeze- up in

the mix inlet hole.

c. Beater motor out on reset. c. Reset the freezer. 11

d. The beater is rotating

counterclockwise.

e. Draw valve bracket

incorrectly attached to draw arm.

f. The circuit breaker is off

or the fuse is blown.

g. Inadequate mix in hopper. g. Fill the hopper with mix. 17

h. The feed tube is installed

upside down.

set too cold.

b. The draw handle is not

fully closed.

a. The thermistor control is

set too warm.

b. Insufficient air space

around the unit. (A/C)

c. Worn scraper blade(s). c. Replace scraper blades

d. Dirty condenser. d. Clean regularly. 22

a. Install the door correctly. 15

b. Call service technician to

adjust hopper temperature.

d. Contact service technician

to correct the rotation.

e. Correctly attach draw

valve bracket to draw arm.

f. Turn the breaker on or

replace the fuse.

h. Install the feed tube with

the hole in the side in the down position.

a. Adjust the thermistor

control knob warmer.

b. The draw handle must be

fully closed.

a. Adjust the thermistor

control knob colder.

b. Allow for adequate air flow

across the condenser.

regularly.

e. The mix is out of date. e. Use only fresh mix. --

f. The beater is rotating

counterclockwise.

g. Product is over beaten. g. Draw off some product to

h. Loss of water (W/C) h. Locate cause of water

Models 441 & 444 Troubleshooting Guide

f. Contact service technician

to correct rotation.

allow fresh product to enter the freezing cylinder.

loss and correct.

Page 28

PROBLEM PROBABLE CAUSE REMEDY PAG E

REF.

4. The mix in the hopper is too cold.

5. The mix in the hopper is too warm.

6. The drive shaft is stuck in the gear box coupling.

7. The freezing cylinder walls are scored.

a. The temperature is out of

adjustment.

a. The temperature is out of

adjustment.

b. Hopper cover is not in

position.

c. The control switch is OFF. c. Place the control switch in

d. Warm mix was placed in

the hopper.

a. Rounded corners of drive

shaft, coupling, or both.

a. The scraper blades and/or

blade clips are damaged.

b. The front bearing is

missing or worn.

c. Unit was placed in AUTO

before all sanitizing solution was removed from freezing cylinder.

d. Broken pins on beater

assembly.

a. Call service technician to

adjust the hopper temperature.

a. Call service technician to

adjust the hopper temperature.

b. Place the cover in

position.

AUTO.

d. Mix added to the hopper

must be below 40_F (4.4_C).

a. Call service technician to

correct the cause and replace the necessary components. Do not lubricate the end of the drive shaft.

a. Replace the scraper

blades and/or clips.

b. Install or replace the front

bearing.

c. Place unit in AUTO only

after priming is complete and all sanitizing solution is removed.

d. Repair or replace the

beater assembly. Be sure the scraper blades are properly seated on pins.

8. No freezer operation with control switch in AUTO.

150701

Troubleshooting Guide

e. The beater assembly is

bent.

a. The unit is unplugged. a. Plug into wall receptacle. --

b. Circuit breaker off or

blown fuse.

c. Beater motor out on reset. c. Reset the freezer. 11

e. Call service technician to

repair or replace the beater and to correct the cause of insufficient mix in the freezing cylinder.

b. Turn circuit breaker on or

replace fuse.

---

Models 441 & 444

Page 29

PROBLEM PROBABLE CAUSE REMEDY PAG E

REF.

9. Excessive mix leakage into the rear drip pan.

10. Excessive mix leakage from the door spout.

1 1. Low overrun. a. Worn scraper blade(s). a. Replace regularly. 26

a. Worn or missing drive

shaft seal.

b. Inadequate lubrication of

drive shaft seal.

c. The seal is installed

inside- out on the drive shaft.

d. Worn rear shell bearing. d. Call service technician to

e. Drive shaft works forward. e. Call service technician. --

f. Wrong type of lubricant is

being used (example: petroleum base.).

a. Worn or missing draw

valve o- rings.

b. Inadequate lubrication of

the draw valve o- rings.

c. The wrong type of

lubricant is being used (example: petroleum base lubricant.).

a. Replace regularly. 26

b. Lubricate properly. 13

c. Install correctly. 13

replace rear shell bearing.

f. Use the proper lubricant

(example: Taylor Lube).

a. Replace regularly. 26

b. Lubricate properly. 14

c. Use the proper lubricant

(example: Taylor Lube).

12. The freezer door works loose.

b. The mix feed assembly is

not installed.

c. Product is broken down

from over- beating.

a. The freezer studs are

damaged.

b. The handscrews are not

tightened.

c. Handscrews are

damaged.

d. Freezer door has

enlarged holes.

e. The beater assembly is

rubbing the back of the door.

b. Install in mix inlet hole. 17

c. Draw off some product to

allow fresh product to enter the freezing cylinder.

a. Call service technician to

replace studs.

b. Tighten the handscrews

equally in a crisscross pattern.

c. Replace the handscrews. --

d. Replace the door. --

e. Call service technician to

correct the problem.

Models 441 & 444 Troubleshooting Guide

Page 30

Section 9 Parts Replacement Schedule

PART DESCRIPTION EVERY 3

MONTHS

Scraper Blades X

Drive Shaft Seal X

Freezer Door Gasket X

Front Bearing X

Draw Valve O- Rings X

White Bristle Brush, 3” x 7” Inspect & Replace

White Bristle Brush, 1” x 2” Inspect & Replace

Black Bristle Brush, 1” x 2” Inspect & Replace

Double- Ended Brush Inspect & Replace

EVERY 4 MONTHS

EVERY 6

MONTHS

if Necessary

ANNUALLY

Minimum

Parts Replacement Schedule

Models 441 & 444

Page 31

Section 10 Limited Warranty on Equipment

TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS

Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor-branded freezer equipment available from Taylor to the market generally (the “Product”) to the original purchaser only.

LIMITED WARRANTY

Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and service as follows. All warranty periods begin on the date of original Product installation. If a part fails due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency, will provide a new or re- manufactured part, at Taylor’s option, to replace the failed defective part at no charge for the part. Except as otherwise stated herein, these are T aylor’s exclusive obligations under this limited warranty for a Product failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed below and on the reverse (if any) of this document.

Product

Soft Serve Frozen Yogurt Shakes Smoothies

Frozen Beverage Batch Desserts

1. If the date of original installation of the Product cannot be verified, then the limited warranty period begins ninety (90) days from the date of Product manufacture (as indicated by the Product serial number). Proof of purchase may be required at time of service.

2. This limited warranty is valid only if the Product is installed and all required service work on the Product is performed by an authorized Taylor distributor or service agency, and only if genuine, new Taylor parts are used.

3. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in the Taylor Operator’s Manual.

Insulated shell assembly Five (5) years

Refrigeration compressor (except service valve)

Beater motors Two (2) years

Beater drive gear Two (2) years

Printed circuit boards and Softech controls beginning with serial number H8024200

Parts not otherwise listed in this table or excluded below

LIMITED WARRANTY CONDITIONS

Part Limited Warranty Period

Five (5) years

Two (2) years

One (1) year

4. Defective parts must be returned to the authorized Taylor distributor or service agency for credit.

5. The use of any refrigerant other than that specified on the Product’s data label will void this limited warranty.

LIMITED WARRANTY EXCEPTIONS

This limited warranty does not

1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of defective parts, replacement parts, or new Products.

2. Normal maintenance, cleaning and lubrication as outlined in the T aylor Operator’s Manual, including cleaning of condensers.

Models 441 & 444 Limited Warranty on Equipment

cover:

131206

Page 32

3. Replacement of wear items designated as Class “000” parts in the Taylor Operator’s Manual.

4. External hoses, electrical power supplies, and machine grounding.

5. Parts not supplied or designated by Taylor, or damages resulting from their use.

6. Return trips or waiting time required because a service technician is prevented from beginning warranty service work promptly upon arrival.

7. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing, unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning supplies.

8. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty, accident or condition beyond the reasonable control of Taylor; operation above or below the electrical or water supply specification of the Product; or components repaired or altered in any way so as, in the judgment of the Manufacturer, to adversely affect performance, or normal wear or deterioration.

9. Any Product purchased over the Internet.

10. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the inadequacy or interruption of electrical service.

1 1. Electricity or fuel costs, or increases in electricity or fuel costs from any reason whatsoever.

12. Damages resulting from the use of any refrigerant other than that specified on the Product’s data label will void this limited warranty.

13. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.

14. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential damages, so this limitation may not apply to you.

This limited warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to jurisdiction.

LIMITA TION OF WARRANTY

THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE COMPONENTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR INCIDENT AL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS, PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.

LEGAL REMEDIES

The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or complaint with the Product, stating the defect or complaint and a specific request for repair, replacement, or other correction of the Product under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.

Taylor Company

a division of Carrier Commercial Refrigeration, Inc.

750 N. Blackhawk Blvd.

Rockton, IL 61072, U.S.A.

Limited Warranty on Equipment

Models 441 & 444

Page 33

Section 11 Limited Warranty on Parts

TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE P ARTS

Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor genuine replacement components and parts available from Taylor to the market generally (the “Parts”) to the original purchaser only.

LIMITED WARRANTY

Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service as follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency, will provide a new or re- manufactured Part, at Taylor’s option, to replace the failed defective Part at no charge for the Part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty for a Part failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed below and on the reverse (if any) of this document.

Part’s Warranty Class Code or Part

Class 103 Parts¹ Three (3) months Class 212 Parts² Twelve (12) months

Class 512 Parts Twelve (12) months

Class 000 Parts No warranty

Taylor Part #072454 (Motor- 24VDC *C832/C842*) Four (4) years

LIMITED WARRANTY CONDITIONS

1. If the date of original installation of the Part cannot be otherwise verified, proof of purchase may be required at time of service.

2. This limited warranty is valid only if the Part is installed and all required service work in connection with the Part is performed by an authorized Taylor distributor or service agency.

3. The limited warranty applies only to Parts remaining in use by their original owner at their original installation location in the unit of original installation.

4. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in the Taylor Operator’s Manual.

5. Defective Parts must be returned to the authorized Taylor distributor or service agency for credit.

6. This warranty is not intended to shorten the length of any warranty coverage provided pursuant to a separate Taylor Limited Warranty on freezer or grill equipment.

Limited Warranty Period

7. The use of any refrigerant other than that specified for the unit in which the Part is installed will void this limited warranty.

1, 2

Except that Taylor Part #032129SER2 (Compressor-Air-230V SERV) and Taylor Part #075506SER1 (Compressor-Air-115V 60HZ) shall have a limited warranty period of twelve (12) months when used in Taylor freezer equipment and a limited warranty period of two (2) years when used in Taylor grill equipment.

131206

Models 441 & 444 Limited Warranty on Parts

Page 34

LIMITED WARRANTY EXCEPTIONS

This limited warranty does not

1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of defective Parts, replacement Parts, or new Parts.

2. Normal maintenance, cleaning and lubrication as outlined in the T aylor Operator’s Manual, including cleaning of condensers or carbon and grease buildup.

3. Required service, whether cleaning or general repairs, to return the cooking surface assemblies, including the upper platen and lower plate, to an operational condition to achieve proper cooking or allow proper assembly of release sheets and clips as a result of grease build-up on the cooking surfaces, including but not limited to the platen and plate, sides of the shroud or top of the shroud.

4. Replacement of cooking surfaces, including the upper platen and lower plate, due to pitting or corrosion (or in the case of the upper platen, due to loss of plating) as a result of damage due to the impact of spatulas or other small wares used during the cooking process or as a result of the use of cleaners, cleaning materials or cleaning processes not approved for use by Taylor.

5. Replacement of wear items designated as Class “000” Parts in the Taylor Operator’s Manual, as well as any release sheets and clips for the Product’s upper platen assembly.

6. External hoses, electrical power supplies, and machine grounding.

7. Parts not supplied or designated by Taylor, or damages resulting from their use.

8. Return trips or waiting time required because a service technician is prevented from beginning warranty service work promptly upon arrival.

cover:

9. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing, unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning supplies.

10. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty, accident or condition beyond the reasonable control of Taylor; operation above or below the gas, electrical or water supply specification of the unit in which a part is installed; or Parts or the units in which they are installed repaired or altered in any way so as, in the judgment of Taylor, to adversely affect performance, or normal wear or deterioration.

1 1. Any Part purchased over the Internet.

12. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the inadequacy or interruption of electrical service.

13. Electricity, gas or other fuel costs, or increases in electricity or fuel costs from any reason whatsoever.

14. Damages resulting from the use of any refrigerant other than that specified for the unit in which the Part is installed will void this limited warranty.

15. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.

16. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential damages, so this limitation may not apply to you.

This limited warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to jurisdiction.

Limited Warranty on Parts

Models 441 & 444

Page 35

LIMITA TION OF WARRANTY

THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS, PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.

LEGAL REMEDIES

The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.

Taylor Company

a division of Carrier Commercial Refrigeration, Inc.

750 N. Blackhawk Blvd.

Rockton, IL 61072, U.S.A.

Models 441 & 444 Limited Warranty on Parts