Taylor 3879 User Manual

Model 3879

Digital Kitchen Scale

Instruction Manual

Thank you for purchasing a Taylor® digital kitchen scale. Your Taylor ® scale is an example of
superior design and craftsmanship. Please read this instruction manual carefully before use.
Keep these instructions handy for future reference.

Battery Information

This scale operates on 2 – 3 volt CR2032 lithium batteries (installed). There is a strip under the
lithium battery cover to prevent battery drain in shipping. Please remove the strip before
continuing with these instructions. Also, some models have a static cling label on the lens to
prevent scratching. Please remove before use.

Replace the batteries when the Low Battery warning “ ” appears on the display, or the
readings grow dim or irregular. To replace the batteries:

1. Use two 3 volt CR2032 lithium batteries. Always replace all batteries at the same time; do not
combine old and new batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable (ni­cad, ni-mh, etc.) batteries. Do not dispose of batteries in fire, as batteries may explode or leak.
Remove the batteries if the scale will not be used for a long period of time.

2. Remove screw (or screws) from the battery compartment cover on the bottom of the scale
and remove the cover.

3. Remove the old batteries from the compartment.

4. Place the new batteries with the “+” sign up into the battery compartment.

5. Replace the battery compartment cover and screw(s).
NOTE: Please recycle or dispose of batteries per local regulations.

WARNING: Batteries may pose a choking hazard. Do not let children handle batteries.
PRECAUTION: Do not dispose of batteries in fire. Batteries may explode or leak. Remove the

batteries if the scale will not be used for a long period of time.

General Weighing Operation

1. Place the scale on a hard, level surface.

2. Press the “ /TARE” button to turn the scale on. The display will show “ ” and then zero

when it is ready for use. If the display does not show zero, press the “ /TARE” button to reset
(tare) the scale to zero.

3. Your scale weighs in pounds/ounces (lb oz), grams (g), fluid ounces (fl. oz.) and milliliters
(ml). Press the “MODE” button to change the units of measurement.

4. Place the item to be weighed on the center of the platform. The weight will display. As you
add weight, the weight displayed increases.

5. The scale will turn off automatically after approximately 1 minute of non-use or if there is no
change in weight after approximately 3 minutes. Press, hold and release the “ /TARE” button
to turn the scale off manually.

Liquid ingredient measurement: The liquid measure feature is suitable for all water based
liquids, including wine, milk, stock, cream etc. Note: Oils have a lower specific gravity, which will
result in a volume reading of approximately +10%. If measuring oils by volume on this scale,
please adjust for this accordingly.

Tare Operation

You may wish to weigh ingredients in a bowl or other container (not included). In this case, you
will need to tare, or offset, the weight of the bowl so that only the weight of the ingredients is
displayed.

1. Choose a container that will safely balance on the platform without tipping or falling. Do not
use a heavy container, as this might reduce the maximum capacity of the scale.

2. While the scale is off, place the empty container on the scale platform. Turn the scale on. The
display will turn on and then show zero. The weight of the container has been zeroed out.

3. Add the ingredient to be weighed. The weight of the ingredient alone will display.

4. The weight of additional ingredients may be tared out as well. For example, if a recipe calls

for ½ lb rice and ½ lb beans, place the rice into the bowl. Once the correct amount of rice is
weighed, press “ /TARE” until the display is reset to zero. Add the ½ lb of beans. Both
ingredients have been accurately weighed in the same bowl.

5. When weights have been tared out, the display will show a negative number when the items
are removed from the scale. To reset the scale back to zero for a new measurement, press
“ /TARE” until the display resets to zero.
Note: The scale can tare (zero out) weights totaling up to 11 lbs / 5000 g / 176 fl. oz. / 5000 ml.
Should “EEEE” appear on the display, the scale has reached maximum tare capacity.

Precautions

1. Clean exposed parts with a soft, slightly damp cloth. To remove stains, use a mild soap.

Never use detergents, excess water, treated cloths, harsh cleaning agents, or sprays. Avoid
contact with acids, such as citrus juices. DO NOT immerse the electronic scale in water or wash
in a dishwasher.

2. Do not tamper with the scale’s internal components. Doing so will invalidate the warranty on
this unit and may cause damage. The scale contains no user-serviceable parts.

3. Although your scale is designed to be maintenance-free, it contains sensitive electronic parts.
Avoid rough treatment. Treat it with care to ensure the best performance.

4. This scale is intended for home/consumer use only. It is not intended for commercial or
medical use.

5. This scale is designed to read weights up to 11 lb x 0.1 oz / 5000 g x 1 g / 176 fl.oz x 0.1 fl.oz
/ 5000 ml x 1 ml. To prevent damage, do not place more than 11 lb / 5000 g / 176 fl.oz / 5000 ml
on it.

6. Do not store scale where you store cleaning chemicals. The vapors from some household
products may affect the electronic components of your scale. Do not store scale on its side.

7. This scale is an extremely sensitive weighing device. In order to prevent run down of the
battery, do not store anything on the scale.

8. Do not dispose of batteries in fire. Batteries may explode or leak. Remove the batteries if the
scale will not be used for a long period of time.

9. “UnSt” = Unstable Warning. Should “UnSt” appear on the display, this indicates the scale is
unstable. Place the scale on a hard, level surface during use.

10. “EEEE = Overload Warning or Tare Capacity Warning: Should “EEEE” appear on the
display during a weighing, this indicates that the maximum weighing or Tare capacity has been
exceeded. Remove the weight immediately; otherwise, permanent damage could occur.

Caution: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

- Consult the dealer or an experienced radio/TV technician for help.

One (1) Year Limited Warranty

Taylor® warrants this product to be free from defects in material or workmanship (excluding
batteries) for one (1) year for the original purchaser from date of retail purchase. It does not
cover damages or wear resulting from accident, misuse, abuse, commercial use, or
unauthorized adjustment and/or repair. If service is required, do not return to retailer. Should
this product require service (or replacement at our option), please pack the item carefully and
return it prepaid, along with store receipt showing the date of purchase and a note explaining
reason for return to:

Taylor Precision Products, Inc.

2220 Entrada Del Sol, Suite A

Las Cruces, New Mexico 88001 USA

www.taylorusa.com

There are no expressed warranties except as listed above. This warranty gives you specific
legal rights, and you may have other rights which vary from state to state.
For additional product information, or warranty information outside the USA, please contact us
through www.taylorusa.com.

©2013 Taylor Precision Products, Inc. and its affiliated companies, all rights reserved. Taylor®
and Leading the Way in Accuracy® are registered trademarks of Taylor Precision Products, Inc.
and its affiliated companies. All rights reserved.

Made to our exact specifications in China.

Not legal for trade.

CP3879 9.13