Taurus KH-84802, Racing Bike Z9 User Manual

USER’S MANUAL

Spining Bike

Taurus Racing Bike Z9

KH-84802

1

Safety Instructions

•
To ensure the best safety of the exerciser, regularly
check it on damages and worn parts.

• If you pass on this exerciser to another person or if
you allow another person to use it, make sure that
that person is familiar with the content and
instructions in these instructions.

• Only one person should use the exerciser at a time.

• Before the first use and regularly make sure that all
screws, bolts and other joints are properly tightened
and firmly seated.

• Before you start your work-out, remove all sharp­edged objects around the exerciser.

• Only use the exercise for your work-out if it works
flawlessly.

• Any broken, worn or defective part must
immediately be replaced and/or the exerciser must
no longer be used until it has been properly
maintained and repaired.

• Parents and other supervisory persons should be
aware of their responsibility, due to situations which
may arise for which the exerciser has not been
designed and which may occur due to children’s
natural play instinct and interest in experimenting.

• If you do allow children to use this exerciser, be
sure to take into consideration and assess their
mental and physical condition and development,
and above all their temperament. Children should
use the exerciser only under adult supervision and
be instructed on the correct and proper use of the
exerciser. The exerciser is not a toy.

• Make sure there is sufficient free space around the
exerciser when you set it up.

• To avoid possible accidents, do not allow children to
approach the exerciser without supervision, since
they may use it in a way for which it is not intended
due to their natural play instinct and interest in
experimenting.

• Please note that an improper and excessive work­out may be harmful to your health.

• Please note that levers amd other adjustment

mechanisms are not projecting into the area of
movement during the work-out.

• When setting up the exerciser, please make sure
that the exerciser is standing in a stable way and
that any possible unevenness of the floor is
evened out.

• Always wear appropriate clothing and shoes
which are suitable for your work-out on the
exerciser. The clothes must be designed in a way
so that they will not get caught in any part of the
exerciser during the work-out due to their form (for
example, length). Be sure to wear appropriate
shoes which are suitable for the work-out, firmly
support the feet and which are provided with a
non-slip sole.

• Be sure to consult a physician before you start
any exercise program. He may give you proper
hints and advice with respect to the individual
intensity of stress for you as well as to your work­out and sensible eating habits.

2

• Assemble the exerciser as per assembly instructions

and be sure to only use the strucutral parts

provided with the exerciser and designed for it.

Prior to the assembly, make sure the contents of

the delivery is complete by referring to the parts list

of the assembly and operating instructions.

• Be sure to set up the exerciser in a dry and even place and

always protect it from humidity. If you wish to protect the place

particularly against pressure points, contamination, etc.,

it is recommended to put a suitable, non-slip mat under the exercise

• The general rule is that exercisers and training devices are no

toys. Therefore, they must only be used by properly informed

or instructed persons.

•

Stop your work-out immediately in case of dizziness,

nausea, chest pain or any other physical symptoms. In

case of doubt, consult your physician immediately.

•Children, disabled and hadicapped persons should

use the exercise only under supervision and in

presence of another person who may give support

and useful instructions.

•Be sure that your body parts and those of other

persons are never close to any moving parts of the

exerciser during its use.

•When adjusting the adjustable parts, make sure they

are adjusted properly and note the marked, maximum

adjusting position, for example of the saddle support,

respectively.

•Do not work out immediately after meals!

3

Exploded drawing

1

2

3

4L

4R

5
6
7

9

8

10

11

12

13
14

42

16

18

17

19

20 21 22

23L

23R

24L

25L

26

27

24R

26

27

25R

28
29

30
31

32

33R

33L

34

35

36

37

39

40

44

47

48

49

56

57

50

53

38

6

5

52

51

59

60

62

61

63

64

65

69

66

68

74

72

53

71

73

67

75

77

76

81

80
30

78

82
86

85

84

88

89

90

92
93
94

88

96 649899

100

101

102

103

104

105

45

46

63

83

83

92
93

7

53

15

87

95

91

12

41

22

79

57

4

Part list

part no. description material specification q'ty

1 main frame

1

2 front stabilizer

1

3 rear stabilizer

1

4L left triangle cap PE 95.7*57.2*51.3 2

4R right triangle cap PE 95.7*57.2*51.3 2

5 allen bolt 35# M8x1.25x20L,8.8level 10

6 spring washer 70# D15.4xD8.2x2T 10

7 flat washer Q235A D16xD8.5x1.2T 10

8 front post

1

9 seat post

1

10 seat

150*260*65,clamp,DD2681 1

11 seat adjustable tube

1

12 L knob 25L

AL

+45# M12*25L 2

13 handlebar

1

14 computer fixing plate

1

15 D plug PS 70*45*14 1

16 cover of front post PE 80*55*147 1

17 protective cover PE 80*55*61 1

18 inner insert PE 80*55*147 1

19 stop plate(1) AL 39*35*17 2

20 sping 72A D12.5*D1.2*20.7 2

21 stop plate(2) AL 38*35*17 2

22 L knob 50L

AL

+45# M10*50L 2

23L left chaincover ABS 744.3*512.4*77.7,with electric hole 1

23R right chaincover ABS 744.3*512.4*82 1

24L left crank 1021M 170*9/16"-20BC 1

24R right crank 1021M+SPH 170*9/16"-20BC 1

25L/R pedal

JD-304,9/16",double bearing-w/o

SPD

1

26 bolt 35# M8x1.0x16,10.9 level 2

27 bolt cover P.E6070 D23x6.5 2

28 screw 35# M10*1.5*20L 5

29 nut Q235A M10*1.5*8T 5

30 round cross bolt Q235A M5x0.8x15L 4

31 pin ABS D6*26.5*7.7 1

32 cross screw 10# ST4.2*1.4*20L 9

33L left cover of brake ABS+15% 95.4*53*33.4 1

5

Fibre

33R right cover of brake ABS+15%

Fibre

95.4*53*31.2 1

34 brake handlebar

Zn alloy

101.1*48.2*37 1

35 belt

PK,J5,1295L 1

36 puelly ADC-10AL D239.8*23,PK,J6 1

37 BB sets

127.5L 1

38 flat washer Q235A D25*D8.5*2T 2

39 outer flywheel A1050 D420*14 1

40 inner flywheel FC20 D290*34.3 1

41 cable plug PVC D4*D12*13 2

42 swing connection fixing bracket

1

43

44 screw 35# M6*1*15L,8.8 level 6

45 tension cable

D1.5*350L ,freedom length 56 1

46 lower tension cable

1300L 1

47 magnet fixing bracket

1

48 magnet

Fe

D18*10T 8

49 magnet fixing plate

1

50 axle of magnet fixing bracket Q235A D8.2*65L 1

51 spring 72A D1.2*55L 1

52 flat washer PE D18*D8.5*1.0T 1

53 nylon nut Q235A M8*1.25*8T 5

54 xx

xx

55 xx

xx

56 magnet cell PE 29*3*3 6

57 cross bolt Q235A M5*0.8*10L 2

58 xx

59 adjustable round wheel Q235A+ABS D59*M10*40L 4

60 bolt Q235A M8*1.25*40L,8.8level 2

61 round moving wheel PVC+PP D70.5*23 2

62 bushing copper steel D22.2*D8.2*7T 4

63 nylon nut Q235A M8*1.25*8T 3

64 screw 10# ST4*1.41*12L 10

65 idle wheel fixing plate

1

66 carriage bolt 35# M8*1.25*20L,8.8level 3

67 adjustable bolt Q235A M6*1.0*46 1

68 nut Q235A M6*1*5T 1

69 bearing GCr15 6203-2RS plastic cover 2

6