Tallygenicom T6200 User Manual

A PRODUCT FROM TALLYGENICOM

Line Printer Operator Manual

Serial • Parallel • Twinax • Coax • TCP/IP

T6200 Series

Including IPDS

This Manual is published by T ally Printer Corporation for use with the computer printer described herein. T ransla­tions, reprinting or copying by any means of this manual, complete or in part, in any different form requires our
explicit approval. T ally Printer Corporation reserves the right to revise this manual without notice, for any reason.
This includes, but is not limited to, utilization of advances in the state-of-the-art and changes in the equipment or
configuration thereof. Liability for difficulties arising from unknown or unforeseen technical limitations is dis­claimed.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15, Subpart B of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment gener­ates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference, in which case the user will berequired to correct the
interference at his own expense.

WARNING

Only trained qualified personnel may open covers or remove parts that are not explicitly shown and described
in the Operator’s Manual as being accessible to the operator.

Please Note:

Printer drivers for various operating systems are available on the Internet at our Web Page
http://www.tallygenicom.com or www.tallygenicom.com/worldwide or at your
T allyGenicom distributor .

ACKNOWLEDGMENTS:
“IBM” and “Proprinter” are trademarks of International Business Machines Corporation.

“DEC” is a trademark of Compaq Computer Corp.
“Printronix” and “PGL” are trademarks of Printronix, Inc.
“Epson” is a trademark of Seiko Epson Corp.
“QMS” and “Code V” are trademarks of Minolta-QMS Inc.
“HP” is a trademark of Hewlett-Packard Company .
“Genicom” is a trademark of Genicom L.L.C.

T6200 Series Operator Manual

© February 2005

All rights reserved

TallyGenicom

6020 S. 190th Street

Kent, Washington 98032

Table Of Contents

Table of Contents

Preface...................................................................Preface–1

Introduction .................................................................................... Preface–1

About This Manual ........................................................................ Preface–2

Chapter 1..........................................................................1–1

Site Preparation .........................................................................................1–1

Unpacking your printer.............................................................................1–2

Repacking ...............................................................................................1–2

Reversible Doors ....................................................................................1–2

Figure 1-1. Reversible Doors ........................................................... 1–2

Removing the Shipping Hardware...........................................................1 –2

Figure 1–2. Shipping Screw Locations ............................................ 1–3

Setting Up Paper Stacking Chains ..........................................................1–3

Figure 1-3. Paper Stacking Chains ................................................. 1–3

Interface Connections and Powering Up ...............................................1–4

Interface Connectors .............................................................................. 1–4

Maximum Interface Cable Length ...................................................................... 1–4

Serial/Parallel only.................................................................................. 1–4

Twinax.................................................................................................... 1–4

Coax ...................................................................................................... 1–4

Figure 1-4. Serial/Parallel and FourPlex Interface Connectors (Rear

View) ................................................................................................ 1–4

Connecting the I/O............................................................................................. 1–5

Serial/Parallel......................................................................................... 1–5

Twinax Connector................................................................................... 1–5

Figure 1-5. Connecting the Host Connector Smart T ...................... 1–5

Coax Connector ..................................................................................... 1–6

Figure 1-6. Connecting with the BNC adapter................................... 1–6

Powering Up............................................................................................ 1 –7

Figure 1–7. Printer (Rear View) ....................................................... 1–7

Paper System ............................................................................................1–8

Paper System Components ....................................................................1–8

Figure 1–8. Paper System Components......................................... 1–8

TOC–1

Operator Manual

Tractor Set s ...................................................................................................... 1–8

Figure 1–9. Opening, Locking, and Unlocking Tractors................... 1–8

Platen Gap Wheel and Lever............................................................................. 1–9

Figure 1–10. Platen Gap Adjustment Wheel and Lever .................. 1–9

Platen Gap Sensing........................................................................................ 1–10

Paper T ension Lever ....................................................................................... 1–10

Figure 1–11. Paper Tension Lever................................................. 1–10

Installing the Ribbon Cartridge.............................................................. 1 –11

Figure 1–12. Removing Ribbon Slack .......................................... 1 –11

Figure 1-13. Installing the Ribbon Cartridge.................................. 1–11

Loading Paper ...................................................................................... 1–12

Figure 1–14. Paper Size Specifications ........................................ 1–12

Form Characteristics ...................................................................................... 1–12

Figure 1–15. Paper Box Placement and Paper Path .................... 1–13

Figure 1–16. Column Alignment Scale ......................................... 1–14

Let’s Check .......................................................................................... 1 –15

Chapter 2.........................................................................2–1

Introduction ................................................................................................2–1

Control Panel Components .....................................................................2–1

Figure 2–1. Control Panel ............................................................... 2–1

LED Indicators ........................................................................................ 2–1

LCD (Liquid Crystal Display) ................................................................... 2 –2

Figure 2-2. Control Panel Display ................................................... 2–2

Current St ate..................................................................................................... 2–2

Options ............................................................................................................. 2–2

Current Selection Indicator ................................................................................ 2–2

Paper Indicators................................................................................................ 2–3

Table 2 - 1 Paper Weight Indicators ................................................. 2–3

Key Functions ..........................................................................................2–4

Online/Offline Key.............................................................................................. 2–4

LF Key (Line Feed)........................................................................................... 2–4

FF Key (Form Feed) ......................................................................................... 2–4

TOF Key (Top of Form) ..................................................................................... 2–5

Figure 2-3 . Aligning Form on Tractors ............................................. 2–5

View Key .......................................................................................................... 2–5

Up and Down Arrow Keys ................................................................................. 2–5

Menu/Back Key................................................................................................. 2–6

Enter Key.......................................................................................................... 2–6

Clear Key.......................................................................................................... 2–6

The Clear Menu...................................................................................... 2–6

Config Key........................................................................................................ 2–7

TOC–2

Table Of Contents

Chapter 3.........................................................................3–1

Introduction ................................................................................................3–1

Control Panel Menus ................................................................................ 3–1

Figure 3-1 Control Panel Navigation............................................... 3–1

Categories, Parameters and Selections.................................................3–2

Using Menus............................................................................................ 3–2

How to Print a Control Panel Selections Report................................................. 3–4

Operator Menu ..........................................................................................3–5

Font Category ..........................................................................................3–5

Ser/Par Language ............................................................................................ 3–5

Tx/Cx Language (displays on T winax/Coax printers only) ................................... 3–5

IPDS Language (displays only if IPDS is installed) ............................................ 3–6

Ser/Par Character Set ...................................................................................... 3–6

Matrix................................................................................................................ 3–7

OCRA Density .................................................................................................. 3–7

Ser/Par S tyle..................................................................................................... 3–7

Tx/Cx Style ........................................................................................................ 3–8

IPDS Style......................................................................................................... 3–8

CPI ................................................................................................................... 3–8

Panel Language................................................................................................ 3–8

OCR St andards ................................................................................................ 3–8

Slashed Zero .................................................................................................... 3–8

Compressed 8.................................................................................................. 3–8

Forms Category ......................................................................................3–9

Length (lines) .................................................................................................... 3–9

Length (inches) ................................................................................................. 3–9

LPI.................................................................................................................... 3–9

T op Margin........................................................................................................ 3–9

Bottom Margin .................................................................................................. 3–9

Left Margin........................................................................................................ 3–9

Right Margin ................................................................................................... 3–10

Horz Adjust...................................................................................................... 3–10

Vert Adjust....................................................................................................... 3–10

Print to End Of Form (EOF)............................................................................. 3–10

Quick Access.................................................................................................. 3–11

Eject Distance ................................................................................................ 3–11

Impact............................................................................................................. 3–12

Paper Weight.................................................................................................. 3–12

Fast Slew........................................................................................................ 3–13

Double Strike.................................................................................................. 3–13

Quality (T6218 only) ........................................................................................ 3–13

RibbonMonitor ................................................................................................ 3–13

TOC–3

Operator Manual

RibnMon Thresh.............................................................................................. 3–13

Ribbon Monitor Operation .................................................................... 3–14

Vertical Format Units (VFU) Category.................................................. 3 –15

VFU Enabled .................................................................................................. 3–15

V ertical T ab (VT) Channel................................................................................ 3–15

Skip When ...................................................................................................... 3–15

Configuration Menu ............................................................................... 3–16

Printer Category ................................................................................... 3 –16

Powerup ......................................................................................................... 3–16

Ser/Par Emul .................................................................................................. 3–16

LAN Emulation (LAN Interface only)................................................................. 3–17

Twinax Emul (T winax/Coax only) ...................................................................... 3–17

Dump Mode.................................................................................................... 3–17

Twinax Interface.................................................................................... 3–17

Coax Interface ...................................................................................... 3–17

IPDS Option......................................................................................... 3–17

IO Hold T ime ................................................................................................... 3–17

Report............................................................................................................. 3–18

Current Config...................................................................................... 3–18

All Configs............................................................................................ 3–18

Configs 1-10 ........................................................................................ 3–18

Calibrations.......................................................................................... 3–18

Ribbon Count ....................................................................................... 3–18

Last Fault ............................................................................................. 3–18

Fault Log.............................................................................................. 3–18

Version ................................................................................................ 3–18

Intellifilter .............................................................................................. 3 –18

Beeper Mode.................................................................................................. 3–18

Codes Category ................................................................................... 3–19

Auto LF (Line Feed)........................................................................................ 3–19

Auto CR (Carriage Return).............................................................................. 3–19

Line Wrap....................................................................................................... 3–19

Wrap Line Feed.............................................................................................. 3–19

Print on CR ..................................................................................................... 3–20

Form Feed at TOF .......................................................................................... 3–20

ESC ............................................................................................................... 3–20

Alt ESC (Alternate Escape)............................................................................ 3–20

Upper Only...................................................................................................... 3–20

Code 7F ......................................................................................................... 3–21

Print 80 to 9F Hex ........................................................................................... 3–21

Ignore Char ..................................................................................................... 3–21

Sub Char From ............................................................................................... 3–21

Sub Char To.................................................................................................... 3–21

PTX SFCC ..................................................................................................... 3–21

PTX ALS......................................................................................................... 3–21

TOC–4

Table Of Contents

TOF Control .................................................................................................... 3–22

DC3 Operation ............................................................................................... 3–22

SISO OverszBar.............................................................................................. 3–22

Barcod Top Pos .............................................................................................. 3–22

Oversz T op Pos............................................................................................... 3–22

Graphics Category ............................................................................... 3–23

Code V Command Character (CVCC)............................................................ 3–23

Smooth Size ................................................................................................... 3–23

PY Then .......................................................................................................... 3–23

PN Then.......................................................................................................... 3–23

Dark Bar......................................................................................................... 3–23

Table 3–1. Bar Code Dot Density.................................................. 3–24

Modplot........................................................................................................... 3–24

Figure 3–2. Modplot Example....................................................... 3–24

Version ........................................................................................................... 3–24

Descender...................................................................................................... 3–24

V ertical Scale.................................................................................................. 3–25

Zero ................................................................................................................ 3–25

SFCC............................................................................................................. 3–25

Special Function Command Character (SFCC)............................................... 3–25

Code V Language .......................................................................................... 3–25

Free Format.................................................................................................... 3–25

Automatic PY .................................................................................................. 3–26

MTPL Bar ....................................................................................................... 3–26

Secured.......................................................................................................... 3–26

IGP T erminator................................................................................................ 3–26

BlkMax H ........................................................................................................ 3–26

BlkMax V ........................................................................................................ 3–26

BlkMin H ......................................................................................................... 3–26

BlkMin V ......................................................................................................... 3–26

Postnet Density............................................................................................... 3–26

PGL Terminator............................................................................................... 3–26

Ignore T erm ..................................................................................................... 3–27

Configurations Category ...................................................................... 3 –27

Save ............................................................................................................... 3–27

How to Save Configurations ................................................................. 3–27

Load ............................................................................................................... 3–28

Powerup Config .............................................................................................. 3–28

Config n Label - (where n = 1 to 10)................................................................. 3–28

How to label a configuration slot ........................................................... 3–28

Serial I/O Category............................................................................... 3 –29

Baud............................................................................................................... 3–29

Data Bits......................................................................................................... 3–29

Stop Bit s......................................................................................................... 3–29

Parity .............................................................................................................. 3–29

8th Bit ............................................................................................................. 3–29

TOC–5

Operator Manual

Protocol .......................................................................................................... 3–29

St atus Enquiry ................................................................................................. 3–30

DTR Function.................................................................................................. 3–31

DTR Polarity ................................................................................................... 3–31

Busy Polarity ................................................................................................... 3–31

RTS Function .................................................................................................. 3–31

Robust Xon ..................................................................................................... 3–31

Parallel I/O Category............................................................................ 3–32

POPC (Print On Paper Command) ................................................................. 3–32

8th Bit ............................................................................................................. 3–32

Bi-Directional.................................................................................................. 3–32

Intellifilter Category .............................................................................. 3–33

Serial.............................................................................................................. 3–33

Parallel ........................................................................................................... 3–33

Twinax/Coax ................................................................................................... 3–33

LAN ................................................................................................................ 3–33

Twinax/Coax Category ......................................................................... 3 –34

Send P A (Coax Only) ...................................................................................... 3–34

Address (Twinax Only)..................................................................................... 3–34

SPD (Coax Only) ............................................................................................ 3–34

SCD (Twinax Only).......................................................................................... 3–34

SLD ................................................................................................................ 3–34

Host (Font) Style (T winax Only) ........................................................................ 3–35

Screen Size (Screen) (Coax Only)................................................................... 3–35

Case (Coax Only)............................................................................................ 3–35

Compatibility Switches (Coax Only)................................................................. 3–35

IR Delay (Coax Only) ....................................................................................... 3–36

Hex Passthrough............................................................................................. 3–36

EPC ............................................................................................................... 3–37

GrA VM (Graphics A VM) .................................................................................. 3–37

IPDS Category (IPDS Only) ................................................................. 3 –38

Address (Twinax Only)..................................................................................... 3–38

Density ........................................................................................................... 3–38

Dark Bar......................................................................................................... 3–38

Smooth Size ................................................................................................... 3–38

Zero ................................................................................................................ 3–38

Host Override.................................................................................................. 3–38

TCP/IP Menu - LAN Interface Only ....................................................... 3–39

IP Address ........................................................................................... 3–39

Gateway................................................................................................ 3–39

Subnet .................................................................................................. 3–39

Test Menu ................................................................................................ 3–40

TOC–6

Table Of Contents

Pattern Category .................................................................................. 3 –40

Print ................................................................................................................ 3–40

Fault Override Category....................................................................... 3 –40

Paper Motion .................................................................................................. 3–40

Diag Category ...................................................................................... 3 –41

Cal-Paper (Calibrate Paper Out)..................................................................... 3–41

Help Menu ............................................................................................... 3–41

Appendix A ..................................................................... A–1

Introduction ............................................................................................... A–1

Messages.................................................................................................. A–1

Faults...................................................................................................... A–1

Fault Correction Procedure ...............................................................................A–1

Table A–1. Display Messages.........................................................A –2

Table A–2. Paper/Printing Corrective Action ...................................A–6

TOC–7

Operator Manual

TOC–8

Blank

Page

Preface

Introduction

Preface

The T6200 Series offers the
following I/O configurations
(Modules):

• Standard Serial/Parallel

• FourPlex (Standard plus

Twinax/Coax)

• FourPlex IPDS

• LANPlex (Standard plus

Ethernet 10/100 BASE-T)

• LANPlex IPDS

In less than five minutes you can add
other configurations by inserting a new
module. Installation instructions come with the module.

All interface configurations and printer setups are performed through the
control panel. In addition, the printer’s operational configuration is stored in
nonvolatile memory; you’ll never have to reconfigure your printer because of a
power loss.

Pref–1

Operator Manual

About This Manual

Chapter 1: Setting Up Your Printer

In Chapter 1, you are instructed on how to set up your printer. You will find

criteria for site selection, instructions for removing the protective shipping

hardware from your printer, and locations of connectors for printer to host

communications and power hookups. In addition you will find instructions on

how to install the ink ribbon, load paper, and adjust the paper movement

mechanisms.

Chapter 2: Printer Control Panel

This chapter explains the various components of the Control Panel and their

functions in various printer modes.

Chapter 3: Printer Menus and Configuring Your Printer

Chapter 3 explains the different menus that are available on your printer and

all of the parameters contained in them. It also presents Menu Tutorials that

show how to perform a variety of different menu operations.

Appendix A: Troubleshooting

Appendix A contains a listing of the error and fault messages that may appear

on the Control Panel Display and various troubleshooting procedures and

problem fixes.

Specifications

This section lists and explains technical aspects of printer performance and

general design specifications.

Conventions

We use the following conventions throughout this manual.

Notes are additional important or helpful information.

CAREFUL!

This symbol marks information about actions that may damage the equipment

or injure the user.

Pref–2

Chapter 1

Site Preparation

Choosing a site for your printer is important because the environment
affects your print quality. The best site for your printer is one that is
protected from dirt and heavy dust, and has a moderate temperature
and humidity range. In addition, the power source should be adequate
for printer operation and protected from power surges.

Keep the following factors in mind when choosing a printer location:

Keep the operating environment temperature between 50°F and 104°F
(10°C and 40°C).

Do not locate your printer near air conditioners, open windows,
heaters, nor in other areas where the temperature changes abruptly.

Chapter 1: Setting Up Your Printer

The relative humidity should be between 10% and 90%
(noncondensing). Be sure to locate the printer away from any sources
of moisture, such as water faucets, refrigerators, and humidifiers.

The heat load contribution to the environment is 188 BTUs per hour at
idle and can go as high as 2050 BTUs per hour under continuous full­load printing conditions.

Keep your printer away from dust, dirt, and open flames.

Plug your printer into a grounded (3-prong) outlet.

Minimum floor space recommended for your printer is 36" wide x 36"
deep (91.4 cm x 91.4 cm) to allow air movement around the printer.
Allow space to open printer doors as well. When the doors are fully
opened, the printer takes up 6.5feet (2.0 m) of floor space.

1–1

Operator Manual

Unpacking your printer

Instructions for unpacking your printer are located on the outside of the

shipping container. After you have removed your printer from its

container, store the shipping materials for possible later use.

Repacking

Repacking your printer for storage or shipping is the reverse order of

unpacking. If shipping materials are needed, you can reorder them from

your dealer.

Reversible Doors

Both front and back doors may be installed to open either left or right:

Removing the Shipping Hardware

The Shipping Hardware consists of 4 screws, identified by red tags, that

secure the printer base to the inside mechanism, tie restraints that

secure the Paper Stacking Chains to the Wire Exit Rack inside the back

door of the printer, and a rubber band holding the platen open.

CAREFUL!

DO NOT power up your printer before removing the

shipping hardware.

1–2

Figure 1-1. Reversible Doors

Chapter 1: Setting Up Your Printer

Figure 1–2. Shipping Screw Locations

Setting Up Paper Stacking Chains

Paper exits the print area through a set of passive Paper Stacking Chains
that help fold and stack printed forms uniformly. Proper loading of the
paper in the tractors improves paper stacking (see Loading Paper).

Release the restraints securing the chains to the wire guides. Make sure
chains are not tangled.

Figure 1-3. Paper Stacking Chains

1–3

Operator Manual

Interface Connections and Powering Up

Interface Connectors

Properly secure the cable to the printer interface using the correct
connectors.

CAREFUL!

Shielded I/O cables must be used on all installations to

comply with FCC regulations.

Maximum Interface Cable Length

Serial/Parallel only

Your printer should be located within 50 feet (15.2 meters) (cable
length) of your computer for a serial interface, or 6 feet (2 meters) for
parallel interfaces. Communication distances farther than these can
cause data transmission problems and printing errors.

Twinax

The Twinax interface allows a maximum of 5,000 feet (1.5 km) between
the host computer and the last device. Distances longer than this can
cause transmission problems and data errors.

Coax

The Coax interface allows a maximum of 5,000 feet (1.5 km) from the
host computer to the printer. Distances longer than this can cause
transmission problems and result in data errors.

Figure 1-4. Serial/Parallel and FourPlex Interface Connectors (Rear

View)

1–4

Connecting the I/O

After connecting each interface to your printer, run a print job from the
Host Computer to verify proper function of the printer.

Serial/Parallel

The serial interface operates up to 38.4 kBaud and uses a standard DB
25 serial cable connector and standard RS-232-C signals.

The Centronics parallel port is IEEE-1284 compliant and uses a 36-pin
1284-B type connector (AMP 555119-1 or equivalent).

To connect the Serial or Parallel I/O cable, plug in the cable to the
proper connector on the I/O panel.

Twinax Connector

To connect your printer to a Twinax host system, use the Smart T
connector. Plug the DB-15 connector into the Host Interface plug on the
printer I/O panel.

If you are installing a printer on an active system, go through the
following list before connecting the Twinax cable(s).

Chapter 1: Setting Up Your Printer

• Verify that the printer address matches the one given it on the
host and that no addresses are duplicated anywhere on the line.
You can check the address of the printer by accessing the HELP
Menu on your printer control panel and printing out a Control
Panel Selections Printout (see Chapter 3).

• Make sure the printer is turned OFF.

• Terminate the device immediately up cable (between the printer
and the host) from the printer.

• Any jobs going to devices down cable (between the printer and
the end of the network) must be put on HOLD.

• Place any devices that are down cable from the printer OFFLINE.

Now connect the cable from the out connector of the up cable device to
either side of the Host Connector Smart T and if there are devices down
cable, connect the cable going to them to the other side of the Smart T.
The Smart T automatically takes care of terminating the Twinax line or
allowing throughput of data to devices located down cable from the
printer.

Figure 1-5. Connecting the Host Connector Smart T

1–5

Operator Manual

Your Twinax hookup is now complete and it is time to test your printer to
verify its operation. Load your printer with paper and an ink ribbon.
Run the IBM printer verification test. If the test is successful, your
installation is complete.

Twinax Trouble Checklist

If the Printer Verification Test fails, check the following:

If all of the above check out and you still have problems, call your
Customer Support Representative.

• Does the printer have the correct address setting?

• Does the address in the system configuration match the setting
on the printer?

• Is the device type in the system configuration correct for the type
of printer being emulated?

• Is the cable to the device immediately up cable on the Twinax line
correctly connected?

• Are the devices down cable functioning properly?

• Is the last device on the line properly terminated?

• Is the printer properly configured?

Coax Connector

Your printer uses a DB-15 to Coax connector pigtail.

To connect your printer to a Coax system, use the BNC adapter. Connect
the adapter to the Host Interface plug on the printer I/O. Make sure that
the printer is turned off, then attach the Coax cable to the BNC adapter.

Figure 1-6. Connecting with the BNC adapter.

1–6

Powering Up

The power switch is located on the left side of the printer, and the power
and interface connectors are inside the printer housing, accessible
through the back door.

Chapter 1: Setting Up Your Printer

Figure 1–7. Printer (Rear View)

Step 1.

Make sure the power is off. Connect the power cord inside the cabinet,
and run it through the opening in the bottom of the printer. Plug the
power cord into a power outlet.

Always use a grounded (3-prong) single-phase outlet.

Step 2.

Turn the power on.

The printer runs a self-test each time it is powered up to check the main
processor and buffers for errors. Note that when you turn the printer
on this time, the Paper Out error displays. Don’t be alarmed, we’ll take
care of that when we load paper. If any other error message appears in
the display, check Appendix A for a description of the error and what
actions are necessary to clear the error.

When connecting the Twinax interface at this time, other messages
that may appear are Setup Address and Lost Sync (28). These messages
appear because the printer/host interface has not been properly set up.
If you cannot connect the interface at this time, you can still test certain
aspects of printer performance by placing the printer Offline (depress
the Online/Offline key), then entering the Menu Mode. While in Menu
Mode you may select print and operation parameters or test certain
printer systems.

1–7

Operator Manual

Paper System

Paper System Components

The Tractors, Platen, Paper Iron and Ribbon Cartridge are all parts of
the paper system. The first two assemblies are involved in how the
paper moves past the print mechanism and through the printer.

Figure 1–8. Paper System Components

Tractor Sets

Your printer has two tractors to control paper movement, located
above the print area.

A lever on each tractor keeps it locked in place on a horizontal shaft. To
reposition a tractor, unlock the tractor and move it horizontally on the
shaft (See Loading Paper).

1–8

Figure 1–9. Opening, Locking, and Unlocking Tractors

Platen Gap Wheel and Lever

The Platen Gap Lever opens and closes the platen gap for loading paper
and ribbon.

The wheel rotates to let the platen accommodate different thicknesses of
paper. The higher the letter, the wider the platen gap. Once it's set, you
don't need to readjust it until you need to load paper of a different
thickness.

Chapter 1: Setting Up Your Printer

Figure 1–10. Platen Gap Adjustment Wheel and Lever

The Control Panel will be used to adjust the Platen Gap; see chapter 2.
When loading paper with a changed thickness, adjust the wheel until it's
snug against the form, but not too tight. Run a print test and adjust the
platen gap wheel to obtain optimum print quality and paper movement.
The print should be crisp and dark, with no smearing. Paper should
move smoothly through the print mechanism. Here are some things to
look for:

• If the platen gap is open too far, the print may start fading out,
especially on the last sheet of a multi-part form.

• If the platen gap is too narrow, the ribbon will start smearing ink
on the page, especially when the ribbon is moving and the paper
is not. In extreme cases, the shuttle may stop, and the paper may
jam.

1–9

Operator Manual

Platen Gap Sensing

Paper Tension Lever

The T6300 has a mechanism that senses the platen gap, used in
conjunction with the Paper Weight and Impact Parameters to control
paper movement and hammer impact force. This is explained in
Chapter 3.

When the platen is open, the position is sensed, printing is disabled and
the Platen Open message is displayed on the control panel.

The Paper Tension Lever controls the vertical tension between the upper
and lower sets of tractors.

Figure 1–11. Paper Tension Lever

Paper tension can affect your print quality. Raising and lowering the
Paper Tension Lever during a print test is one method that can be used
to obtain optimum print quality. Here are some things to look for when
you begin printing.

• If the paper tension is too loose, the dot columns and dot rows
may not line up.

• If the paper tension is too tight, the paper holes will start
elongating vertically and may tear. This can also lead to poor
paper stacking and jams.

1–10

Chapter 1: Setting Up Your Printer

Installing the Ribbon Cartridge

Step 1.

Make sure the printer is Offline or power is off. Open the printer lid and
open the platen gap using the lever, then remove the old ribbon by
lifting it straight up off of the Ribbon Platform.

Step 2.

Remove slack in the new ribbon by turning the knob on the ribbon
cartridge counter-clockwise, then slip the ribbon over the two ribbon
guides and between the front and rear panels of the ribbon shield on
the printer.

Ribbon Control Knob

Figure 1–12. Removing Ribbon Slack

Step 3.

Press down lightly on the cartridge while turning the ribbon knob
counter-clockwise until it seats on the cartridge drive posts. Make sure
that the ribbon does not twist or fold over.

Figure 1-13. Installing the Ribbon Cartridge

Step 4.

Close the Platen Gap lever.

1–11

Operator Manual

Loading Paper for Regular Printing

Your printer is designed to use a continuous sheet, sprocket-fed paper.
It can handle:

• Six-part forms (1 original and 5 copies) with a maximum
thickness of .025" (0.6 mm).

• Page widths of 2.5" to 18" (6.4 cm to 45.7 cm).

Form Characteristics

Minimum Form Width - "A" 2.50 in. 64 mm

Maximum Form Width - "A" 18.00 in. 457 mm

Horizontal Form Adjustment - "C"

Without Horizontal Vernier

With Horizontal Vernier - Forms < 15.86 in.

With Horizontal Vernier - Forms > 15.86 in.

Tractor Hole to Paper Edge (per ISO 2784) - "D"

Figure 1–14. Paper Size Specifications

Minimum 0.16 in. 4.1 mm
Maximum 1.80 in. 45.7 mm

Minimum 0.16 in. 4.1 mm
Maximum 1.80 in. 45.7 mm

Minimum "A " - 15. 70 in. "A" - 399 mm
Maximum . 1.80 in. 45.7 mm

Minimum 0.208 in. 5.3 mm
Maximum 0.264 in. 6.7 mm

1–12

Chapter 1: Setting Up Your Printer

Step 1.

Make sure the printer is Offline or printer power is off.

Step 2.

Open the new box of paper. Remove the box top so that the paper can
be pulled out freely, then place the new box of paper under the printer.

Figure 1–15. Paper Box Placement and Paper Path

Step 3.

Raise the printer lid and open the doors on all of the tractors.

Step 4.

Feed the paper up and through the printer, as shown above.

Step 5.

Place the left-side paper holes onto the upper left tractor pins and close
the tractor door.

1–13

Operator Manual

CAREFUL!

The left end of the scale (5 & 10 CPI) on the ribbon platform marks the
position of Column 1. Before printing, make sure that this marker is
aligned with the desired position on the form. To align the paper on the
column marker, unlock the tractor and slide it to the desired position,
then lock it in place.

Figure 1–16. Column Alignment Scale

Step 5.

Unlock the right tractor and move it so that the paper holes align directly
over the tractor pins, then close the tractor door. Gently push the tractor
to the right until the paper is smooth and reasonably taut, then lock the
tractor.

Step 6.

Unlock the lower tractors, place the paper over the tractor pins, then
adjust the tractors so that the pins line up with the paper holes. Lock the
tractors.

Step 7.

Adjust the platen gap, the use the Paper Tension Lever to adjust the
tension on the form between the upper and lower tractors. Don't forget
to reset the top-of-form (TOF) before procedding with printing (see
Chapter 2).

1–14

Let’s Check

Chapter 1: Setting Up Your Printer

Before beginning a print job, check the following items:

• All tractor locking levers are locked.

• The upper tractor sprocket pins are snug against the top of each
paper hole. The bottom tractor sprocket pins are snug against the
bottom of each paper hole. The paper holes should not be
elongated or torn horizontally or vertically.

• The tractors are feeding correctly.

• The paper is properly routed through the print mechanism and
between the Paper Stacking Chains.

• Make sure that the Paper Stacking Chains are hanging properly
without being tangled.

Now that you have installed your printer and loaded it with the ink
ribbon and paper, you are ready to configure it to function on your
system. Chapter 2 discusses the Control Panel Components and how
they function, and Chapter 3 lists and explains all of the menu
parameters available for configuring your printer.

1–15

Operator Manual

1–16

Blank

Page

Chapter 2

Introduction

In this chapter you will learn about the Printer Control Panel and how it is used
to control printer functions.

Control Panel Components

The Control Panel is located on the top cover. You can use it to program and
direct most printer functions.

Chapter 2: Printer Control Panel

LED Indicators

The green POWER Indicator illuminates whenever there is power to the printer.
The red FAULT Indicator illuminates whenever an error or fault is detected. A

message also appears on the display to indicate what kind of fault is present
(see Appendix A for explanations of all error and fault messages).

32-character

2-line display

Includes a beeper

3 LED

Indicators

Figure 2–1. Control Panel

11 control

keys

The yellow ON LINE Indicator illuminates to indicate whenthe printer is ready to
accept data.

2–1

Operator Manual

LCD (Liquid Crystal Display)

The LCD is located at the left of the Control Panel. It shows printer status,
menu selections, and normal, fault, and error messages. The LCD is divided
into four main areas. Each area displays one of the following: Current State,
Paper Indicators, Options, and Current Selection Indicator.

Offline

Current State

Operator Menu

Paper
Indicator

Current State

The Current State appears in positions 1-15 of the first display line. During
normal operation, this area displays Online, Offline or a fault message. If
you're using the printer menu, the menu, category or parameter items display
here as well.

Options

The Options appear in positions 1-15 of the second display line. During
normal operation, this area is blank. When you access the printer menu, this
area shows each item as you scroll through the menu.

When you are in Offline mode using the Config key, this area displays configu­ration labels as you scroll though each one (see Key Functions, this chapter).

Current Selection Indicator

The Current Selection Indicator occupies position 16 of the second line of the
display. When you're in menu mode and scrolling through menu options, an
asterisk appears when you come to the currently selected parameter.

Options

Current
Selection
Indicator

Figure 2-2. Control Panel Display

2–2

Paper Indicators

The Paper Indicators occupy position 16 of the first line of the display. Table
2-1 shows the meaning of each indicator.

Indicator Paper Weight Impact

(blank) The platen is in the Light The platen is in the Normal

h The platen is in the Medium The platen is in the Normal

H Paper Weight is set to The platen is in the Normal

Chapter 2: Printer Control Panel

Weight zone when Paper Impact zone when Impact is
Weight is on Auto or set on Auto or set to Normal.
to Light.

Weight zone when Paper Impact zone when Impact
Weight is on Auto or set to is on Auto ot set to Normal.
to Medium.

Heavy. Impact zone when Impact is

on Auto or set to Normal.

h The platen is in the Medium The platen is in the High

Weight zone when Paper Impact zone when Impact is
Weight is on Auto or set to is on Auto ot set to High.
to Medium.

H The platen is in the Heavy The platen is in the High

Weight zone when Paper Impact zone when Impact is
Weight is on Auto or set to is on Auto ot set to High.
to Heavy .

The platen is in the Light Impact is set to High.
Weight zone when Paper
Weight is on Auto or set to
to Light.

Table 2 - 1 Paper Weight Indicators

2–3

Operator Manual

Key Functions

Online/Offline Key

LF Key (Line Feed)

This key toggles the printer between Online and Offline states, or exits from
the menu directly to an Online state. When the printer is Online, the indicator
will light, and the printer is ready to accept data from the host. When it's
Offline, it cannot accept host data. In the Offline state, you may change
parameter selections, load paper, and so on.

This key advances the paper one line. It performs the same function whether
the printer is Online or Offline. You may auto-repeat this command by holding
down the key.

While Online With Data Buffered

Any buffered data falling in the next line (as defined by the current LPI set­ting), prints. This repeats upon subsequent LF keystrokes as long as there is
data in the buffers. If pressed while printing is in progress, the printer ignores
the key command and maintains the Top of Form position.

While Online with No Data Buffered

Paper advances one line. While printing is in progress, the printer ignores the
command and maintains the Top of Form position.

While in a Fault Condition

Paper advances one line. No data is printed and the Top of Form position
moves down one line. This allows the use of the LF Key to advance paper
while in a Paper Out condition without printing any buffered data.

FF Key (Form Feed)

This key performs the same function whether the printer is Online or Offline.

While Online With Data Buffered

Any buffered data falling between the current form position and the top of the
next form (as defined by the current Form Length setting), prints. This func­tion repeats upon subsequent FF keystrokes as long as there is data in the
buffers. The printer ignores the command while printing is in progress and
maintains the Top of Form position.

While Offline With No Data Buffered

Paper advances to the top of the next form. The printer ignores this command
while printing is in progress and maintains the Top of Form position.

When In a Fault Condition

Pressing the FF Key while in a Fault Condition advances the paper one form.
No data prints, and the Top of Form position is maintained. This allows the use
of the FF Key to advance paper while in a Paper Out condition, without printing
any buffered data.

2–4

TOF Key (Top of Form)

When you load paper, you line the top of your form (usually the perforation)
with the indicated position on the tractor (see Figure 2-3). Once the paper is
loaded, pressing this key moves the paper so that printing commences at the
proper position on the form.

10 CPI

10 20 30

51015

5 CPI

Chapter 2: Printer Control Panel

Align Desired Top-Of-Form
Location At This Point

View Key

Holding down this key moves the paper up so that you can see the last line
that was printed. If you press it while a job is printing, it will suspend the print
job until you release the key.

Up and Down Arrow Keys

Online, these keys make fine adjustments to the Top of Form position.
Offline, these keys position the paper in preparation for setting the Top of

Form position. (In this mode, these keys will auto-repeat if you hold them
down). They are also for scrolling through Menu items (see Menu/Back key,
next).

After making adjustments, it's not necessary to reset the Top of Form
(unless a different top margin is required for a new form).

In Operator, Config, or Test modes, the Up and Down Arrow keys scan lists
of categories, parameters, and selections.

Figure 2-3 . Aligning Form on Tractors

2–5

Operator Manual

Menu/Back Key

Enter Key

Clear Key

Pressing this key allows you to access menu selections, which you can scroll
through using the Up and Down Arrow keys. Pressing the Menu/Back key
returns you to a previous selection. This key command is only available when
the printer is in an Offline mode.

In any of the menus, this key allows you to enter a lower level, to assign a
selection to a parameter, or to perform a menu function.

When the printer is in a Paper Out Fault condition, and the PrntEOF
Parameter is set to Off, pressing the Enter Key allows printing to the
end of the current form. When PrntEOF is set to On, the printer auto­matically prints to the end of the current form.

Online, pressing the Clear key clears the panel of any errors that do not

cause the printer to go Offline, such as "Parity Error."
Offline, if the printer is in a clearable fault condition, the fault clears upon

pressing the Clear key. If it's not in a clearable fault condition, pressing the
Clear key brings up the Clear menu.

In Operator, Config, Test, or Help menus, pressing this key returns the
printer to Offline status.

The Clear Menu

Clear Buffers (not in T winax or Coax)

Clears all buffers. It also resets the application task to its initial state.

Clear Ribbon Count

When using the Ribbon Monitor feature, this selection must be used to clear
the ribbon count when changing ribbons. See the RibbonMonitor and
RibnMon Thresh setting in the Forms category of t he Operator menu in
Chapter 3.

Clear All Configs

Copies the Default Configuration settings into all saved configurations. Any
parameters not listed on the Configuration Report (see Chapter 3), such as
special characters downloaded from the host computer, are unaffected.

Clear Current Config

Copies the Default Configuration settings into the current configuration. Any
parameters not listed on the Configuration Report, such as special characters
downloaded from the host computer, are unaffected.

2–6

Chapter 2: Printer Control Panel

Clear Reset

The printer controller performs a hardware reset. You may use this in lieu of
cycling power to the printer. As with cycling power, the Powerup Configuration
is loaded as the Current Configuration (see Chapter 3).

Clear Cancel (Twinax and Coax only)

Allows you to send a Cancel Job message to the host via the I/O while the
printer is Offline. It performs the same functions as the Cancel Job request
when the printer is Online. The display reads "Cancel Job" and the printer
remains Offline.

For Coax, this function is valid only in NonSCS mode.
Clear Reprint (Coax only)

This allows you to reprint the previous buffer contents. After reprinting the
buffer, the printer returns to Enable Print condition and continues printing the
rest of the job. This option is convenient in cases of paper jams or any time
you do not need to send the complete job.

This function is valid only in Non SCS Mode. If you select this in SCS
Mode, an Invalid Key error message displays for a few seconds.

Config Key

Offline

This is a shortcut to the Load Configurations menu item (see Chapter 3),
allowing you to enter a menu where any of ten saved configurations can be
loaded into the Current Configuration.

Use the Up and Down Arrow keys to scroll through the configurations. Press­ing the Enter key loads the one you choose.

2–7

Operator Manual

2–8

Blank

Page

Chapter 3: Printer Menus and Configuring Your Printer

Chapter 3

Introduction

In this chapter you will learn about the printer’s modes, multilevel menus,
parameters, parameter values, and how to select and store parameter values
as part of a configuration. You will also learn how to obtain printouts that show
all available parameters, current configuration settings, and technical informa­tion like accumulated running time and operating thresholds.

In addition, any time you need to review the active selections in each configu­ration you may do so by printing out the Configuration Report (see Configura­tion Menu). This report shows all configurations and how they are set up.

Control Panel Menus

This section discusses the menus and how to access and select parameter
values from them for formatting documents, controlling print operations, or
testing the printer. The four main menus are Operator, Config, Test, and Help.

Offline

ONLINE

OFFLINE

Online

Menu

Categories

Category

Parameters

Parameter

Settings

Navigations
within
Operator,
Config,
and Test
menus

MENU

CLEAR

ONLINE

OFFLINE

ONLINE

OFFLINE

CLEAR

ONLINE

OFFLINE

CLEAR

Operator

Menu

Arrow Keys

Config

Menu

Arrow Keys

Test

Menu

Arrow Keys

Help

Menu

Arrow Keys

Figure 3-1 Control Panel Navigation

3–1

Operator Manual

Categories, Parameters and Selections

Within the Operator, Config, and Test menus, there are a number of catego­ries. Within each category is a list of parameters. In some cases, a param-

eter can execute a function upon pressing Enter, or in other cases, it displays
yet another list of selections for that parameter.

The Help menu has no categories or parameters. You'll use this menu to print
out a list of all menus, categories, parameters and selections. See "How to
Print a Control Panel Selections Report", this chapter.

Using Menus

Now you are ready to learn how to access menus. Here are some things to
remember:

• You must first be in Offline state to access menus.

• The Online/Offline key takes the printer Online and Offline.

• All scrolling is performed using the Up and Down Arrow keys.

• The Enter key selects parameter values or initiates a desired proce-

dure.

• Active selections are marked with an asterisk (*).

• To exit Menu mode without making changes, depress the Clear key or

the Online/Offline key.

When the printer is Online, the display reads:

Online

The name of the last loaded configuration displays on the lower line.
In this state, the only keys that respond are:

• Up and Down Arrow

• LF

• FF

• Clear

• View

• Online/Offline

When the printer is Offline, the display reads:

Offline

3–2

Chapter 3: Printer Menus and Configuring Your Printer

In the Offline state, pressing the Menu key gives you access to the first level of
the menu system. Upon doing this, the display reads:

Offline

Operator Menu

Now, in the Offline state, you may access one of four available menus (Opera­tor, Config, Test, and Help) by pressing the Up and Down Arrow keys, followed
by Enter.

As you scroll through (with Operator displaying first) the display reads in order:

Offline

Config Menu

Offline

Test Menu

Offline

Help Menu

Each of these menus except for Help has multiple levels of categories, selec­tions and parameters. You access them by scrolling through the lists with the
Up and Down arrows, and by pressing Enter when you see the category,
parameter, or selection you want.

Example: Changing Form Length Using the Menu System

Here is how the menu system works. If, for instance, you wanted to
change the Form Length from the default of 66 lines to 65 lines, this is how
you do it:

1. Make sure your printer is in an Offline state. If it's not, press the
Online/Offline key.

2. Press the Menu key. The display reads:

Offline

Operator Menu

3. Press Enter to select the Operator menu. The display reads

Operator Menu

Font

4. Press the Down Arrow key until you see Forms.

Operator Menu

Forms

3–3

Operator Manual

5. Press the Enter key. Your display then reads:

Forms

Form Length

6. Form Length is the selection you want, so press the Enter key. The
display reads:

Form Length

*

66

(The asterisk means that 66 is the current selection.)

7. You want to change this to 65. Press the Down arrow once and the
display reads:

Form Length

65

8. Press the Enter key. The Form Length is set to 65. Exit the menu
mode by pressing the Clear key.

It's helpful to remember that at any time, you may leave a menu in one of two
ways.

• Depress the Clear key to leave Menu Mode and remain Offline.

• Depress the Online/Offline key to leave Menu Mode and return the

printer to Online.

How to Print a Control Panel Selections Report

The organization of the multilevel menus is shown on the Control Panel Selec­tions Printout. All current selections are marked with an asterisk.

1. Make sure the printer is Offline.

2. Press the Menu/Back key .

3. Use the Up or Down arrow keys until you see Help Menu on the dis-

play .

4. Press Enter.

The Control Panel Selection Report begins printing. When it's finished, press
the FF key, tear off the sheet and use it to become familiar with menu items.

All of the menu items and explanations are also listed on the following pages
in this chapter.

3–4

Operator Menu

Following are explanations of each menu category and parameter.

Font Category

This category contains parameters that control how print looks on a page and
the display language. The Level 2 headings are as follows:

Ser/Par Language

This allows you to select the language used by emulations attached to the
Parallel, Serial, and LAN ports (except for LAN-IPDS). The language selec­tion defines the character substitutions in Hex locations 23, 24, 40, 5B, 5C,
5D, 5E, 60, 7B, 7C, 7D, and 7E. The default is US.

The details of the character substitutions can be found in the Line Printer
Applications Manual. The possible selections are:

Chapter 3: Printer Menus and Configuring Your Printer

IRV US German
Norwegian/Dan French UK
Spanish Swedish/Finish Italian
Japanese Portuguese Canadian
Hungarian Chinese French T6
Swedish T6 Italian T6 Canadian Alt
Swedish Basic French Withdrwn Nor/Dan T6
UK LG Dutch LG Finnish LG
Swiss LG JIS Roman LG Nor/Dan LG
Swedish LG Turkish LG Cro-ASCII
Nor/Dan Epson French Epson UK Epson
Spanish Ep son Italian Epson Norwegian Epson
Danish Epson Sp anish 2 Epson Lat Amer Epson

Tx/Cx Language (displays on Twinax/Coax printers only)

This parameter defines the language used by emulations attached to Twinax
and Coax ports (except IPDS). The default is US.

*The details of the character sets can be found in the Line Printer Applications
Manual. The possible selections are:

US German Norwegian/Dan
French UK Spanish
Swedish/Finish Italian Japanese
Portuguese Canadian Belgian
Brazilian Spanish S peak Code Page 905
Code Page 1026 Katakana Multinational

3–5

Operator Manual

IPDS Language (displays only if IPDS is installed)

Ser/Par Character Set

This defines the language used by the IPDS emulation. The default is US.
The details of the character sets can be found in the Line Printer Applications

Manual. The possible selections are:

Internat'l 500 English US 037 Aus/German 273
Nor/Dan 277 French 297 English UK 285
Sp anish 284 Fin/Swedish 278 Italian 280
Jap/English 281 Portuguese 037 Canadian 037
Belgian 500 Brazilian 275 Spanish S pk 284
Katakana 290 Portuguese 282 Swiss 500
Icelandic 871 Latin2 870 Cyrillic 880
Turkish 905 Turkish 1026

This allows you to select a character set that occupies locations Hex 80
through FF used by emulations attached to the Parallel, Serial, and LAN ports
(except for IPDS over LAN). The default depends on the following:

Emulations Default Character Set

T ally ANSI, P600, P6000, P5000 Latin 1 8859-1
IBM Proprinter, MTPL, Genicom4800, Genicom5000 Code Page 437
Epson FX-1 180 Italic
DEC LG DEC MultiNation
HP 2564C Roman-8

The details of the character sets can be found in the Line Printer Applications
Manual. The possible selections are:

Latin1 8859-1 Latin2 8859-2 Latin9 8859-15
Cyrillic 8859-5 Greek 8859-7 Turkish 8859-9
Code Page 437 Code Page 850 Code Page 851
Code Page 852 Code Page 855 Code Page 857
Code Page 863 Code Page 866 Code Page 869
Code Page 928 Code Page 437G Code Page 866B
Code Page 1250 Code Page 1251 Code Page 1252
Code Page 1253 Code Page 1254 DEC MultiNation
DEC Turkish Siemens Turkish DEC T echnical
DEC Supplemental Greek Supplemental Turkish Supplemental
Mazovia Kamenicky Roman-8
Katakana ISO 13 Line Draw Italic

3–6

Matrix

There are two font modes available on your printer. One mode is called En­hanced and the other is called Constant Density. Enhanced fonts include Draft
and Data Processing, Near Letter Quality (Gothic and Courier), and Optical
Character Recognition Fonts (OCR-A and OCR-B). Constant Density fonts
include only Draft and Data Processing. In addition, the available CPI selec­tions are different for each mode.

When this parameter is set to Enhanced, characters printed at 12, 13.3, 15,
and 17.14 will use a denser character matrix than that of the default CDF
matrix. If this parameter is set to CDF and a CDF font matrix is not available
for the current Font Style and CPI, the Enhanced matrix will be selected.

CPI Selection is limited in Constant Density Mode. The Specifications
Section of this manual has a listing of the CPI selections available in
Constant Density fonts. If you select a CPI value, either through the
Control Panel or via an escape sequence from the host computer, that is
not available in Constant Density Mode, the printer will automatically
switch to Enhanced Mode for printer output.

OCRA Density

This parameter sets the density for the OCRA font. There are three options:
Standard, Enhanced, and High. Standard is the default option and prints at 85
DPI vertical. Choosing the Enhanced option will cause the OCR-A font to be
printed at 96 DPI vertical. Choosing the High option will cause the OCR-A font
to be printed at 144 DPI vertical. Standard and Enhanced print at the same
speed, but the enhanced font is slightly shorter than the Standard. High prints
at a slower speed.

Chapter 3: Printer Menus and Configuring Your Printer

Ser/Par Style

This allows you to select the font style used by emulations attached to the
Parallel, Serial, and LAN port (except for LAN-IPDS). For emulations that
support downloaded fonts, you can use this parameter to select the download
font. The default is DP.

Style selections

Draft (High-speed)
DP (Data Processing, Default selection)
Gothic (Sans Serif NLQ)
Courier (Serif NLQ)
OCR-A (Optical Character Recognition)
OCR-B (Optical Character Recognition)
Download (Selects the downloaded font)

3–7

Operator Manual

Tx/Cx Style

IPDS Style

CPI

This allows you to select the default font style used by emulations attached to
the Twinax and Coax ports (except IPDS).

Style selections

Draft (High-speed)
DP (Data Processing, Default selection)
Gothic (Sans Serif NLQ)
Courier (Serif NLQ)
OCR-A (Optical Character Recognition)
OCR-B (Optical Character Recognition)

This allows you to select the default font style used by the IPDS emulation.

Style selections

Draft (High-speed)
DP (Data Processing, Default selection)
Gothic (Sans Serif NLQ)
Courier (Serif NLQ)

This parameter allows you to select characters per inch (CPI) settings. The
possible selections are 5, 6, 6.67, 7.5, 8.33, 8.57, 10, 12, 13.33, 15, 16.67,

17.14, and 20. The default is 10 CPI.

Panel Language

This option allows you to set up the printer to display messages on the Control
Panel in a particular language. Printed reports also display in your chosen
language. The possible selections are English (default), German, French,
Italian, Swedish/Finish, and Spanish.

OCR Standards

This parameter defines the combination of ANSI and DIN st andards to be used
for the OCR-A and OCR-B character sets. The default value is dependent on
the emulation. The possible selectiosn are:

A: ANSI B:ANSI This means ANSI OCR-A and ANSI OCR-B
A: DIN B:ANSI This means DIN OCR-A and ANSI OCR-B
A: ANSI B:DIN This means ANSI OCR-A and DIN OCR-B
A: DIN B:DIN This means DIN OCR-A and DIN OCR-B

Zero

As an aid in distinguishing zeros from the uppercase letter O, you can choose
to have your zeros slashed (Ø). Default is open (non-slashed) zeros.

Compressed 8

Use this option for higher lines per inch settings to decrease the space be­tween the dot-rows of the printed characters. This increases the vertical
spacing between each printed line, which increases readability without chang­ing the current LPI settings. Compressed 8 functions at 8 LPI and above (at
any CPI). Setting this parameter to ON causes all characters printed at 8,
9,10, or 12 LPI to be compressed vertically. The default is OFF.

3–8

Chapter 3: Printer Menus and Configuring Your Printer

Forms Category

This category is used for setting form specifics.

Length (lines)

If you wish to define the length of your form in lines, you may select a form
length from 1 to 255. The default option is 66.

Length (inches)

If you wish to define the length of your form in inches, you may select a form
length from 0.1 to 25.5 inches. The default option is 11.0 inches.

LPI

This allows you to set the lines per inch. The possible selections are 1.5, 2, 3,
4, 5, 6, 8, 9, 10, and 12. The default setting is 6 LPI.

Top Margin

This parameter dictates where the first print line is located on the page. The
Top Margin location is measured in lines from the current Top-of-Form location.
The range is 0 to 255, with the default at 0.

IPDS

In the IPDS emulation, the value set in this category is not used, since the
value is set up in the data stream.

Bottom Margin

This parameter allows you to set the bottom margin. The Bottom Margin is
measured in lines from the current Top-of-Form location. The range is 0 to 255,
with the default at 66.

IPDS

In the IPDS emulation, the value set in this category is not used, since the
value is set up in the data stream.

The Bottom Margin and Top Margin selections are translated into a
physical location on the page. Subsequent changes in LPI affect this
location. If the new location does not exactly correspond with a line
position, no asterisk is shown as a "current setting" indicator.

For example:

The initial Bottom Margin selection was line 60 and the current LPI was 6.
The Bottom Margin location would be 10 inches from the Top-of-Form location.
If the LPI was then changed to 10 LPI the selection for Bottom Margin would
change to line 100.

Left Margin

You can place the left margin at any column number across the page, using
selections 1 to 272. The range of selections for this parameter depends on the
CPI setting. (Column 1 is the Default). The left margin must be less than or
equal to the right margin.

3–9

Operator Manual

Right Margin

IPDS

In the IPDS emulation, the margin settings are absolute in regards to column
number, so that changing the CPI also changes the physical location of the
margin.

You can place the right margin at any column number across the page. As with
Left Margin, the range of this value depends on the CPI. (Column 136 is the
Default selection). The right margin must be greater than or equal to the left
margin.

IPDS

In the IPDS emulation, the margin settings are absolute in regards to column
number, so that changing the CPI also changes the physical location of the
margin.

If a requested margin setting indicates a column number that is greater
than the maximum allowable for the current CPI, the printer will default to
the last valid setting.

The current value of the right and left margins reflects a physical location
on the form, and therefore, changes when the CPI setting changes. If the
physical location of the right or left margin does not exactly correspond
with a line position after changing the CPI (characters per inch) setting,
there will be no current setting indicator (asterisk).

Horz Adjust

The print position on the form may be adjusted horizontally in increments of
1/30th an inch. The default option is 0.

Vert Adjust

The print position on the form may be adjusted vertically in increments of 1/72nd
an inch. The default option is 0.

Print to End Of Form (EOF)

Before changing paper it is best to print to the end of the current form. This
parameter allows you to set up the printer to print to the end of the form auto­matically. The settings are On and Off, with the default at Off.

CAREFUL!

For Print to EOF to function properly the last print line of the form must
come before the perforation. If the Form Length setting allows printing to
go over a perforation, it is possible for the printer to continue printing in a
paper out situation without any paper in the printer, which may damage
the printer.

If Print to EOF is ON:

The printer automatically prints to the end of the form then stops. The display
reads Paper Out, the alarm sounds, and the FAULT indicator illuminates. At
this point you can load the machine with more paper. After you load paper,
ensure that the platen gap is closed, adjust the top-of-form location and make

3–10

Chapter 3: Printer Menus and Configuring Your Printer

sure the paper is feeding correctly. When you are ready, depress the Clear
key to clear the fault condition, then place the printer Online and continue
printing.

If Print to EOF is OFF, you have two options:
Option 1:

loaded, set the correct top-of-form location and check for proper paper feed.
When you are ready, depress the Clear key to clear the fault condition, then
place the printer Online and continue printing.

The printer will start printing where it left off, which may cause im­proper form and print location alignment.

Option 2:

form, then the display reads Paper Out and the FAULT Indicator illuminates. At
this point you may load more paper on the printer. After loading paper, set the
correct top-of-form location and check for proper paper feeding. When you are
ready, depress the Clear key to clear the fault condition, then place the printer
Online and continue printing.

The Paper Out Sensor will not work unless the Top-Of-Form location
has been set properly (see Chapter 2).

Quick Access

This feature provides a way for the printer to position printed forms for quick tear­off access. When Quick Access is enabled, the paper is moved to the tear posi­tion by pressing the Enter key. If the printer is online and the current print job is
finished, pressing the Enter key will move the paper to the tear position and the
Quick Access Timeout will start. New print jobs will not start printing until the
timeout has expired and the paper has automatically moved to the next available
top of form. (This typically results in a blank form separating the next-to-print form
from the previously printed form.) Alternatively, the printer may first be placed
Offline before pressing the Enter key . Placing the printer back online will align the
paper as described above and printing will resume as soon as data is received.
The default option for the Quick Access parameter is Disabled. The dist ance that
the paper is ejected is set with the Eject Distance parameter (below). The delay
interval between print jobs is set with the Eject Delay parameter (below).

Load a new supply of paper into the printer. After paper has been

Depress the Enter key. The printer prints to the end of the current

Eject Distance

The Eject Distance parameter allows you to select the distance at which the pa­per ejects during a Quick Access operation. The units are in tenths of an inch,
from 0.0 to 25.5; the default is 12.2 inches.

Eject Delay

This parameter specifies the timeout interval in seconds (after which printing will
resume) when Quick Access is Enabled while the printer is Online. The default is
30 seconds.

3–11

Operator Manual

Impact

Paper Weight

Impact is the relative energy level of the hammer impact on the form being
printed. On Auto (the default), the printer senses the thickness of the form by
the platen gap and varies the setting automatically from Normal to High. If you
want to override it, you can set it to Normal or High (see note after Paper
Weight).

Paper Weight parameter defines the "paper moves" - how the paper motion
and printing work according to the thickness of the paper. If on Auto (the
default), the selection will vary from Light to Heavy depending on the position
of the platen.

The following table illustrates the effect each parameter has on the printer's
relative function (Impulse, Paper Moves, and Slew Speed). If all three param­eters are set to Auto, the Impact and Paper Weight vary according to what the
platen gap sensor tells the printer. The Slew Speed varies from 25 IPS to 40
IPS depending on the Paper Weight setting.

Hammer Paper Slew

Parameters Selection Impulse Moves Speed

Impact High Thump N/A N/A

Normal Tick

Paper Heavy Varies 31 IPS
Weight Medium N/A Accordingly 35 IPS

Light 35 IPS

Fast Slew Enabled N/A N/A 31-35 IPS

Disabled 25 IPS

On the Auto setting, Impact and Paper Weight parameters mirror each other,
because both parameters use the platen gap to sense what is needed. How­ever, in some cases you may want to set each manually. For example, when
printing on thick card stock, you'll need a Heavy Paper Weight but only a
Normal Impact.

The graphic shows how the platen gap setting
affects both the Impact and the Paper Weight.
If you have placed a thick form in the

t

Thick

Form

printer and both Impact and Paper
Weight are set to Auto, the

Heavy

platen gap sensor tells the
printer to set the Paper
Weight to Heavy
and the Impact to
High.

Normal Impact High Impac

Thin

Form

Medium Paper Weight

ght

i

L

3–12

Chapter 3: Printer Menus and Configuring Your Printer

Fast Slew

Slew refers to the high speed paper motion that occurs whenever the printer
moves paper more than one line. If your forms are thin or fragile such that
output stacking is a problem, you can decrease the printer's slew speed by
setting this parameter to Disabled. The default setting is Enabled.

Double Strike

When set to Enabled, the printer strikes each dot twice. Use this to get better
print quality when you are printing on an exceptionally thick form. Default is
Disabled.

Enabling this option decreases the printer throughput by approximately
50%.

Quality (T6218 only)

The Quality panel menu setup option only applies to heavy forms printing on
the T6218 printer model. If the Paper Weight setting is Light, printing
throughput will always proceed at optimum speed.

If the Paper Weight setting is either Medium or Heavy and the Quality
setting is Enhanced, the printing throughput rate will be reduced to ensure
optimum print quality. The throughput reduction for the Heavy Paper Weight
setting is greater than that for the Medium Paper Weight setting.

RibbonMonitor

Enables the Ribbon Monitor feature. The selections are Enabled and Disabled
(default).

The Ribbon Monitor feature helps the printer operator determine when to
replace ribbons for optimum and consistent print quality. It works by counting
the estimated number of characters printed as jobs are printed. Since ribbons
are rated for an estimated number of characters, when the character count
threshold is reached for the current ribbon the operator is notified via the panel
that the ribbon needs to be replaced.

Ribbon Monitor can be disabled at any time. However, the characters printed
count is reset to zero whenever Ribbon Monitor is enabled, so enabling the
feature should only be done with a fresh ribbon.

If the Ribbon Monitor Fault occurs, and is cleared without the ribbon life thresh­old being increased or the ribbon count reset to zero, the “Replace Ribbon”
message will reappear approximately every one million characters until one of
these operations is performed. This message will also appear upon powerup if
the ribbon count is above the threshold at that time.

RibnMon Thresh

Sets the ribbon life threshold of the Ribbon Monitor feature. The default setting
is 40, assumming that a 40 million character ribbon is being used. This setting
should be changed to 60 or 250 if a 60 million or 250 million character ribbon is
used. The setting can be further refined based on the application being printed.

3–13

Operator Manual

Ribbon Monitor Operation

When the number of characters printed reaches the ribbon life threshold, the
current print job will stop, the Fault indicator will light, and the Replace Ribbon
message will appear. When this situation occurs:

Clear the fault with the Clear key. The fault indicator should turn off and
the Replace Ribbon message should disappear.

Look at the recently printed output of the printer to determine if the ribbon
is exhausted. If the quality of the output is still acceptable, you can in­crease the ribbon life threshold through the RibnMon Thresh option. The
the printer can then be placed back online and printing will resume.

If the printed output is too light, then the ribbon is exhausted. Replace the
ribbon with a new one, and reset the ribbon count with the Clear Menu
Ribbon Count option. The printer can then be placed back online and
printing will resume.

If the printing application is particularly heavy, it may be necessary to
decrease the threshold.

The current Ribbon Monitor status can be obtained by printing a Calibrations
Report (see Configuration Menu - Printer Category - Report Option). This
report will inducate whether Ribbon Monitor is enabled, the estimated number
of characters printed since Ribbon Monitor was last reset, and the selected
threshold.

If the LAN interface is installed, the Ribbon Monitor status can be viewed
graphically in WebPanel in the form of a "gas gauge". The size of the gas
gauge bar decreases as a percentage of remaining expected ribbon life. The
color of the bar is green when expected remaining ribbon life is between 51%
and 100%, yellow when between 26% and 50%, and red when 25% or less.

WebPanel can also be configured to send an Email Notification when the
expected remaining ribbon life falls to 25%.

3–14

Chapter 3: Printer Menus and Configuring Your Printer

Vertical Format Units (VFU) Category

VFU Enable

A Vertical Format Unit is a means for loading sets of vertical tabs. These
vertical tabs define various parameters of a form. This parameter applies only
to the emulations which make explicit use of the VFU channels. Setting this
parameter to Enabled causes the printer to use the last loaded EVFU instead
of using the Form Length, Top Margin, and Bottom Margin settings. When an
EVFU is loaded, this parameter is automatically set to Enabled. The default is
Disabled.

VT Channel (Vertical Tab Channel)

You can select which VFU Channel is designated as the Vertical Tab Channel.
This parameter applies only to the emulations which makes explicit use of the
VFU channels. Selections are 1 - 12 and Unused. The default depends on the
emulation as defined in the table under the Emulation selection parameter.

Skip When

This parameter applies only to the emulations which make explicit use of the
VFU channels. This parameter designates where the Skip Length distance will
begin - before or after the Bottom of Form channel. The Skip location is deter­mined by using the designated Bottom-of-Form Channel in the downloaded
VFU. The Skip When parameter only functions when the VFU Environment is
enabled. The default depends on the emulation as defined in the table under
the Emulation selection parameter .

3–15

Operator Manual

Configuration Menu

Following are explanations of each menu category and parameter . For all
available selections under each parameter below, consult the Help Menu
printout.

Printer Category

Powerup

This parameter sets the printer either Online or Offline when the power switch
is turned on. This parameter setting is automatically saved to the Powerup
Configuration when it is changed. The default is Offline.

Ser/Par Emul

This parameter allows you to define which set of printer control commands will
be emulated for data received on the Serial and Parallel ports (except LAN­IPDS). This parameter setting is automatically saved in the Powerup Configu­ration. MT660 is the default selection.

When a new emulation setting is entered through the Printer Control Panel,
emulation dependent parameters in the Current and Powerup configurations
are changed to match the default settings for the selected emulation. The
following table lists those parameters by emulation:

Parameter Tally ANSI Genicom ANSI P5000 P6000 P600

Character Set Latin1 Code Pg 437 Code Pg 850 Latin1 Latin1
OCR-A ANSI ANSI ANSI ANSI ANSI
OCR-B ANSI ANSI ANSI ANSI ANSI
Auto CR OFF ON ON ON OFF
Line Wrap OFF ON OFF OFF OFF
Wrap LF OFF ON OFF OFF OFF
Code 7F FILL FILL Space Space Space
VT Channel 2 12 N/A 12 12
Skip When Before Before N/A After After

Parameter

Character Set Roman-8 DEC Italic Code Pg 437 Code Pg 437
OCR-A ANSI ANSI ANSI ANSI ANSI
OCR-B ANSI DIN ANSI ANSI ANSI
Auto CR OFF OFF ON ON ON
Line Wrap OFF OFF ON ON ON
Wrap LF OFF O FF ON ON ON
Code 7F Fill FILL Delete Char Ignore Delete Buffer

VT Channel 12 12 N/A N/A N/A
Skip When After After N/A N/A N/A

HP 2564C DEC LG01 Epson FX-1180 IBM Proprinter MTPL

3–16

Chapter 3: Printer Menus and Configuring Your Printer

LAN Emulation (LAN Interface only)

Used to select the emulation attached to the Ethernet port when using the
LANPlex interface. The possible selection are the same as the Ser/Par Emul
option.

Twinax Emul (Twinax/Coax only)

Used to select the Twinax emulation when using the FourPlex interface. The
possible settings are IBM 4234, IBM 4210, and IBM 5225. The default is IBM

4234. The Coax emulation will always be IBM 4234.

Dump Mode

Dump Mode is used to troubleshoot problems that may arise when processing
data. It places the printer into a Hex Dump Mode. You can select three styles
of printouts for use as debugging tools. The standard selections are:

OFF: Dump Mode is disabled. (Default selection)
Style1: T wo column output. Text, spaces, and control codes are printed in hexa-

decimal code format in one column and ASCII equivalents in another
column.

Style2: Only control codes are printed in hexadecimal format. ASCII characters are

printed as is and escape sequences force a new line.

Style3: Control codes and spaces are printed in hexadecimal format. ASCII characters

are printed as is and escape sequences force a new line.

Twinax Interface

There is only one style for Twinax. It is similar to the Serial/Parallel S tyle 1,
except the Hex codes are EBCDIC instead of ACSII.

Coax Interface

There is only one style for Coax. It is a unique dump mode that prints the
contents of the PCIA buffer associated with each data buffer.

IPDS Option

If the IPDS option is installed, the dump from the IPDS data stream will be
uniquely formatted regardless of the Dump Mode selection.

IO Hold Time

This parameter allows you to set the amount of time the printer remains locked
onto the I/O on which it is receiving data after data transmission stops. You
can set this to be 5—600 seconds (Default selection = 30 seconds)

3–17

Operator Manual

Report

Current Config

All Configs

Configs 1-10

You can use this parameter to print or display a report.

This selection produces a printed report of the current printer configuration.
The report contains a header which identifies the installed software and
interface, any options that are installed, and statistics for time powered on,
time printing, and total lines printed.

Produces a printed report of all the saved printer configurations. The report
contains a header which identifies the installed software and interface, any
options that are installed, and statistics for time powered on, time printing, and
total lines printed.

Produces a printed report of any of the saved printer configurations. The
report contains a header which identifies the installed software and interface,
any options that are installed, and statistics for time powered on, time printing,
and total lines printed.

Calibrations

Produces a printed report of the printer calibration settings. The report con­tains a header which identifies the installed software and interface, and statis­tics for time powered on, time printing, and total lines printed. The body of the
report shows the values of the current sensor and print timing calibrations. It
also contains a report of the Ribbon Monitor status.

Ribbon Count:

Displays the last fault message on the control panel display.

Last Fault

Displays the last fault message on the control panel display.

Fault Log

Display the fault log.

Version

Displays the version numbers of the installed software on the control panel
display.

Intellifilter

Prints the currently downloaded Intellifilter.

3–18

Beeper Mode

When a fault event occurs, the beeper will sound. There are two options:
Single or Persistent. In the Single mode, each fault event will cause the fault
alert beeper to produce just one short-duration audio tone. In the Persistent
mode, a fault event will cause periodic shor-duration audio tones that cycle
about once per second and will persist until the operator clears the fault.

Chapter 3: Printer Menus and Configuring Your Printer

Codes Category

In this category are parameters that allow you to determine the printer’s re­sponse to certain conditions and to assign values to parameters that are used
by other commands or escape sequences. For the IPDS Emulation, these
options have no function.

Auto LF (Line Feed)

Auto LF causes the printer to perform a Line Feed each time it receives a
Carriage Return Control Code. This parameter is available for host systems
that cannot send a Line Feed Control Code.

Some computers automatically generate a Line Feed of their own at the right
margin. If your system does this and if Auto LF is enabled, it will result in a
double-space between lines of print. Consult your computer manual to deter­mine whether this function should be turned off or on. Default is OFF.

Auto CR (Carriage Return)

Auto CR allows the printer to perform a Carriage Return (moves print location
to the left margin) when it receives either a Line Feed or Vertical Tab Control
Code. OFF is the default value. The default value is dependent on the emula­tion (see Emulate under the Config Menu, Printer category).

Line Wrap

If the printer gets to the right margin without receiving a paper movement
command, the Line Wrap Parameter dictates how the rest of the data will be
treated. If Line Wrap is OFF the excess characters are lost. If Line Wrap is
ON, printer response is determined by the Wrap Line Feed Parameter (see
below).

If Line Wrap is ON and Wrap LF is OFF, the printer performs a Carriage Return
only and overprinting can result.

If Line Wrap is ON and Wrap LF is ON, the printer performs a Carriage Return
plus a Line Feed and excess characters are printed on a new line at the left
margin.

The default value is dependent on the emulation (see Emulate under the Config
Menu, Printer category).

Wrap Line Feed

This parameter works in conjunction with the Line Wrap parameter, above. The
default value is dependent on the emulation (see Emulate under the Config
Menu, Printer category).

3–19

Operator Manual

Print on CR

This parameter is intended for use by customers whose applications embolden
characters by using a CR-only method to selectively reprint all or parts of a line.

Off: Ignore bolding, print as regular text (Default setting)
Double Strike: Print line, then backup to reprint (bold by overstriking)
Bold: Print line once, bold portions printed with enhanced

"bold" style

For example, the application may embolden the word "bold" in the following
sentence by sending:

This is bold<CR> bold<CR><LF>

"Double Strike" corresponds to the previous POCR=ON setting. With "Double
Strike" selected, bolding is accomplished by re-striking the characters at the
same dot positions. This requires a 1-line backup after printing each <CR>
pass; some applications use many passes to print a single bolded line, so
printing throughput may be reduced accordingly.

With "Bold" selected, bolding is accomplished by rendering the bolded charac­ters twice, one with a small offset to create a "shadow" effect. The resulting
print is thicker and thus appears darker. This is the same technique used with
the "bold" character attribute selected via emulation escape sequences.

Form Feed at TOF

This parameter dictates how the printer will respond to a Form Feed Control
Code received from the host computer when it is already at a top-of-form
location. If set to Disabled, the printer ignores the Form Feed Control Code
sent from the host. If set to Enabled (default selection) the printer performs the
requested form feed and advances to the next top-of-form.

ESC

This parameter is valid only in the MT660 and LG01 emulations. When set to
Disabled, the ESC control character is ignored. The default is Enabled.

Alt ESC (Alternate Escape)

This parameter is only valid in the MT660 and LG01 emulations. When set to
Enabled, a "^" (carat) character in column 1 (left margin) followed by a CR or a
CR LF can be used in place of the ESC control code. The default is Disabled.
ESC (see above) must also be Enabled for this to work.

3–20

Upper Only

This parameter allows you to set up your printer to print in uppercase charac­ters only from the active Character Set. When this parameter is enabled, the
lowercase characters in Hex positions 61 through 7A are overwritten by the
uppercase characters in positions 41 through 5A. The default selection is
Disabled.

Chapter 3: Printer Menus and Configuring Your Printer

Code 7F

This parameter allows you to dictate how the printer will react when it receives
a Hexadecimal code 7F. The default value depends on the emulation. (See
the Emulation Parameter, presented earlier in this chapter.)

Ignore: The code is ignored.
Delete Char: The previous character is deleted.
Delete Buffer: The previous characters on the current print line are

Space: A Space character is substituted.
Fill: A Fill character is substituted.

Print 80 to 9F Hex

This parameter defines whether locations 80 through 9F Hex are to be treated
as control characters or printable characters. The function of the control
characters in this area depends on the emulation. The selections are ON
(printable characters) or OFF (control characters). The default value is ON.

Ignore Char

This parameter allows you to select a character that will be ignored in the
incoming data stream. This parameter functions in all emulations and non­downloadable print modes. It does not function in plot mode, font download,
or VFU download. Selections are 0-255, referring to the decimal value of any
8-bit character, or OFF. Default is OFF.

deleted.

Sub Char From

This parameter allows you to select a character that will be replaced by the
character designated by the Sub Char To parameter. This parameter functions
in all emulations and non-downloadable print modes. It does not function in
plot mode, font download, or VFU download. Default is OFF.

Sub Char To

This parameter allows you to select the character that will replace the character
designated by the Sub Char From Parameter. This p arameter functions in all
emulations and non-downloadable print modes. It does not function in plot
mode, font download, or VFU download. Default is OFF.

PTX SFCC

Defines the Special Function Control Character used by the Printronix P5000
emulation. The decimal value of the ASCII character code is entered. The
default value is 1 (SOH).

PTX ALS

Defines the single line Alternate Line Spacing used by the ACK (Hex 06) com­mand in the Printronix P5000 emulation. The possible selections are 8 or 10.3
which define the line density. The default value is 8.

The PTX SFCC and PTX ALS options will only appear if the Printronix
P5000 emulation is selected with the Ser/Par Emul control panel option.

3–21

Operator Manual

TOF Control (Available when Genicom ANSI emulation is selected)

DC3 Operation (Available when Genicom ANSI emulation is se­lected)

SISO OverszBar (Available when Genicom ANSI emulation is se­lected)

Barcod Top Pos (Available when Genicom ANSI emulation is se­lected)

When a new form is defined, the top-of-form position is left unchanged if this
parameter is Enabled (the default). When a new form is defined, and this param-
eter is Disabled, the top-of-form position is reset to the top margin of that form.

This parameter allows DC1 - DC3 operation. When Enabled (default), the printer
can be selected and deselected using DC1 and DC3 control codes. The printer
select/deselect operation is not in effect when Disabled.

This parameter allows SI-SO operation for bar codes and oversize characters.
When Disabled (default), bar code and oversize character modes do not need to
be activated with SO and deactivated with SI. When Enabled, bar code and
oversize character modes will be activated and deactivated using the SO and SI
control codes.

When Enabled (default), the paper position is reset to the top of the bar code
after printing. When Disabled, the paper position is left at the end of the bar code
after printing.

Oversz Top Pos (Available when Genicom ANSI emulation is se­lected)

The paper position will be reset to the top of the oversize characters after printing
when this parameter is Enabled (default). When Disabled, the paper position is
left at the end of the oversize characters after printing.

3–22

Chapter 3: Printer Menus and Configuring Your Printer

Graphics Category

This category allows you to configure certain aspects of the Graphic Process­ing Options on your printer.

Code V Cmd Char

This parameter allows you to change the CVCC. The Default for this parameter
is the ASCII caret ( ^ , Decimal 94, HEX 5E) character.

Smooth Size

This parameter controls the size at which block characters are “smoothed.”
The default is 3, which means that size 3 block characters will be smoothed,
but size 2 block characters will not. This parameter is used by Code V and
PGL.

PY Then

This parameter defines printer response to characters following the ^PY Com­mand on the same line.

None: All data, plus the line terminator are ignored (default)
All: All data is executed
Term: All but the terminator is ignored
Free Format: Depends on the state for Free Format Mode

PN Then

Dark Bar

This command defines printer response to characters following the ^PN Com­mand on the same line.

None: All data plus the line terminator, are ignored (default)
All: All data is executed
Free Format: Depends on the state for Free Format Mode

For PY Then and PN Then: Even though Code V documentation states
that all other data on the line is ignored, some Code V installations do
not follow this rule.

This parameter allows you to set the base dot density at which bar codes will
print. Default is Low .

All bar codes will print at the selected density unless the user program re­quests a higher density. When the user program requests a higher density, the
printer will switch to the next higher density than the base density. The follow­ing table shows the density selections and how they change when the printer
receives a program request for a higher density:

3–23

Operator Manual

Modplot

Table 3–1. Bar Code Dot Density

DarkBar Selection "Normal" Mode "Dark" Mode

Lo w 60 x 72 60 (120) x 144

Medium (Default) 60(120) x 144 120 x 144

High 120 x 144 120 x 144

This parameter eliminates the need to send an Align to Line Boundary
Command (MT660) or an extra Line Feed (LF) Control Code (Printronix) when
exiting Plot Mode. Whenever you are using Plot Mode in these emulations,
set this parameter to ON to avoid graphic and text alignment problems.
(Modplot ON is the Default selection.) In addition to Code V and PGL graph­ics, this parameter also applies to MT660 and Printronix style graphics. It does
not apply to text following Epson or Proprinter graphics.

Line 1: Character Data

Version

This parameter controls the version of Code V the printer emulates. Version 2
is the default selection.

Descender

This parameter controls insertion of the character descender gap between print
lines.

On

Line 2: Plot Data

Line 3: Character Data

Line 1: Character Data

Off

Line 2: Plot Data

Line 3: Character Data

Figure 3–2. Modplot Example

Fixed: The descender gap is always inserted after the line whenever

Descender Mode is ON regardless of whether descenders are
present or not. (Default selection)

Auto: The descender gap is only inserted after lines containing char-

acters with descenders.

3–24

Vertical Scale

This parameter determines whether vertical block characters will be scaled to
the same dimensions as horizontal block characters. S tyle 1 is the default
selection.

Zero

As an aid in distinguishing zeros from the uppercase letter O you can choose to
have your zeros slashed (Ø). Slashed is the default selection. This parameter
is used by code V and PGL.

SFCC

This parameter allows you to change the S pecial Function Command Character .
The Default for this parameter is the ASCII tilde ( ~, Decimal 126, HEX 7E )
character. Options are 1-255 (Decimal designators for ASCII characters).

Chapter 3: Printer Menus and Configuring Your Printer

Style 1: Adds intercharacter gap after the character has been

rotated.
Style 2: Does not add gap
Off: Vertical block characters will be compressed vertically

due to the higher vertical density (72 DPI vs. 60 DPI).

PGL Special Function Command Character (SFCC)

This parameter allows you to change the SFCC. The Default for this parameter
is the ASCII tilde ( ~, Decimal 126, HEX 7E ) character. Selections are 1–255
(Decimal designators for ASCII characters)

Code V Language

This parameter allows you to select the language character set that will be used
for text output in Code V Graphics Mode. The default is US. The available
selections are:

US UK Swedish/Finish
Norwegian/Dan Japanese German

French Italian S p anish

PGL Language

This parameter allows you to select the language character set that will be used
for text output in Printronix Graphics Mode. The default is ASCII. The available
selections are:

ASCII German Swedish
Danish Norwegian Finnish

English Dutch French
S p anish Italian Turkish

Free Format

This parameter turns on Free Format Mode in Code V graphics whenever a ^PY
is encountered. Free Format Mode will remain active until a ^PN or ^O (Free
Format Mode Off) command is received. The default is Off.

3–25

Operator Manual

Automatic PY

MTPL Bar

Secured

IGP Terminator

If Automatic PY is Enabled, the printer is automatically in Code V graphics
mode, and a ^PY command is not needed in the file being sent to the printer to
begin Code V graphics. The default is Disabled.

Setting this parameter will print out barcodes for MTPL. Otherwise, the se­quences will be printed as text only. The selections are ON and OFF, with the
default being OFF. This parameter only affects the MTPL emulation.

In secured mode (ON), normal text characters can be printed to the right or left
of barcodes. In unsecured mode (OFF), it is not possible to print more than
one line with normal characters in the bar code line. The default is ON. This
parameter only affects the MTPL emulation.

This selects the Terminator for IGP. When set to CR, all IGP commands are
required to be terminated with a carriage return. When set to CR/LF, all IGP
commands are required to be terminated with a carriage return and line feed.

BlkMaxH
BlkMaxV
BlkMinH
BlkMinV

These four parameters provide the ability to create block characters using
FreeType font s. However, the user may find that very small FreeType charac­ters are not legible, and very large FreeType characters may print too slowly.
These four allow the user to select the minimum and maximum horizontal and
vertical size of block characters that will be generated using the FreeType
characters.

Postnet Density

Determines whether POSTNET bar codes are printed in Low Density (72 DPI)
or High Density (144 DPI). Low Density is the default setting. POSTNET bar
codes printed in High Denisty wil print at half the speed of Low Density.

PGL Terminator

Determines whether or not a CR-LF terminator for PGL commands will cause a
line feed to occur.

CR: Will allow line feeds which follow the carriage return to be executed.

Example: ~EXECUTE;TEST<cr><lf>

<cr><lf>
~NORMAL<cr><lf>

3–26

The above example would execute three line feeds following the job EXAMPLE.
CR-LF: Will NOT execute line feeds following a carriage return. In the above

example, the LFs would not execute. This is the default.

Chapter 3: Printer Menus and Configuring Your Printer

Ignore Term

Determines whether or not a line feed following the CR terminator, an SFOFF, or
an IGOFF command will cause a line feed to occur. There are two options: En­abled (usually the default), and Disabled (the default for Genicom ANSI).

Disable : A LF following the CR terminator SFOFF or IGOFF command will

execute.
Example: ~SFOFF<cr><lf>

~IGOFF<cr><lf>

Enable: A LF following the CR terminator in the above example will not ex-

ecute.

Configurations Category

Your printer can save up to ten personalized configurations, so you don't have
to recreate configurations you use frequently. In addition, each configuration
you save can be tagged with a label of up to 15 characters. When you first
receive your printer, each label is a generic "CONFIG" followed by a number 1
through 10 (See How to Save Configurations, next).

Save

If you have a configuration you are going to use multiple times, you may want
to save it. You'll use this parameter to do this.

How to Save Configurations

1. Set up the printer parameters the way you want them.

2. Make sure the printer is Offline (press the Online/Offline key), and

press the Menu/Back key to enter Menu mode.

3. Use the Up or Down Arrow key to find the Configurations menu, and
press Enter.

4. Scroll through the list of configurations. If you have not labeled them
(see Config n Label) they will be listed as CONFIG 1 - CONFIG 10.
Press Enter to save your configuration into any of these slots.

Next time you want to use this configuration, use LOAD.

3–27

Operator Manual

Load

Powerup Config

Config n Label - (where n = 1 to 10)

How to label a configuration slot

You will use this parameter to load any of your saved configurations into the
Current Configuration. Use the Load parameter to choose the configurations
you've previously saved.

You will use this parameter to designate any of the saved configurations as the
configuration that is loaded when the printer powers up. Scroll through the
Powerup Config parameter to select the configuration you want to use, then
press Enter. The default Powerup Config is CONFIG1.

You may want to call your configurations something more intuitive than
CONFIGs 1 through 10. This parameter is used to set 15-character labels for
each configuration slot.

1. Make sure the printer is Offline.

2. Press the Menu/Back key to enter Menu mode.

3. Use the Up and Down Arrow keys to get to the Config menu, and then

press Enter.

4. Scroll until the display reads Configurations, then press Enter.

5. Scroll until you see Config n label, where n is the number of the con-

figuration you want to label (1-10).

6. Press Enter.

7. A cursor appears underneath the first letter (C). Use the Up and Down

Arrow keys to scroll to the number or letter you want to use. Repeat
for up to 15 characters, pressing Enter after each letter. You must
press Enter 15 times even if your label is shorter.

8. Press Clear or Menu to save it. Now, when you use the Save or Load
parameters, this configuration name appears in the slot you've chosen.

3–28

Chapter 3: Printer Menus and Configuring Your Printer

Serial I/O Category

Serial Interface is a style of host computer-to-printer I/O communications. It
requires certain parameters to be properly set in order for the printer and host
computer to communicate.

Baud

The Baud parameter allows the user to set up the printer to receive data at
different transmission speeds. The baud rate must be the same value at both
ends of the communication line. 9600 is the default selection.

Data Bits

You can choose the number of data bits per byte. 8 bits is the default selec­tion.

Stop Bits

This parameter sets the number of serial stop bits. 1 is the default selection.

Parity

Parity is a method the printer uses to verify that each byte of data it receives is
exactly what the host computer transmitted. When selected, it keeps track of
the number of high bits in each byte (either odd or even). Default is None.

8th Bit

Protocol

The printer must match the parity of the host computer.

If 8 bits per byte is selected under Data Bits above, you use this parameter to
determine how the 8th bit is to be used. If this bit is to be ignored, the param­eter should be set to unused. If the bit is to be used, the parameter should be
set to Data. Data is default, used for 8-bit characters.

The printer and host computer must establish common signals, understood by
both units, for indicating when to send new data and when to stop sending
data. For IPDS, this parameter allows the serial protocol to be set to either
Ready/Busy or XON/XOFF. For all other printers, there are six additional
protocols. The eight protocols are:

Ready/Busy (Default selection)
Xon/Xoff
Enq/Ack (Enquiry/Acknowledge)
Etx/Ack (End of Text/Acknowledge )
Etx/Ack/Nak (End of Text/Acknowledge/Neg. Acknowledge )
Ack/Nak (Acknowledge/Negative Acknowledge )
Xon/off/Etx/Ack (XON/XOFF/End of Text/Acknowledge )
Xon/off/Enq/Ack (XON/XOFF/Enquiry/Acknowledge)

The above protocols are explained in detail in the Applications Manual.

3–29

Operator Manual

Status Enquiry

When this option is enabled, the host may send an enquiry packet to the
printer requesting status. The printer will then send back a 1 byte packet
denoting the status of the printer. If this option is set to OFF (the default), no
packet will be sent back. The Status Enquiry feature may be enabled in con­junction with any other protocol. When enabled and the host sends an ENQ
character, the printer responds by sending a printer status byte. The status
byte is designed to be a printable code and is the only printable code the
printer can transmit.

The bit pattern is as follows:

Bit Meaning/Value

7 Parity if 7 bit data and parity enabled (MSB)
6 Always a 1
5 1 if Data Overrun
4 Always a 0
3 1 if Parity Error
2 1 if Paper System Error or Platen Open
1 1 if Offline
0 1 if Busy (fault or buffer full) (LSB)

The Status Enquiry Feature is slightly different when the current emulation is
the HP2564C. Instead of responding to the ENQ character, the printer will
respond to the ESC ? DC1 sequence. The bit pattern of the status response is
as follows:

Bit Meaning/Value

7 Parity if 7 bit data and parity enabled (MSB)
6 Always a 0
5 Always a 1
4 Always a 1
3 0 if Parity Error, Data Overrun, or Buffer Overflow
2 1 if Offline
1 1 if Busy (fault or buffer full)
0 1 if Paper System Error or Platen Open (LSB)

3–30

DTR Function

This parameter allows the user to change the operation of the Data Terminal
Ready (DTR) line on the printer interface. The DTR line is used to indicate
printer status to the host computer.

Busy (Default selection)

In this mode the DTR line is used to signal the host to stop sending data be­cause the printer buffer is 85% full. However, some cabling systems require
the DTR Line of the printer to be configured differently. This cabling scheme
can interfere with printer transmission or host reception of the Xoff signal when
using the Xon/Xoff Serial Protocol. This situation can result in Buffer Overflow
and Data Overrun situations and loss of data.

Offline

When this selection is active, the DTR Line is used to signal only that the
printer is Online or Offline. Unlike the Busy selection, the Offline selection will
not interfere with operation of the Xon/Xoff Communication Protocol.

Power

Chapter 3: Printer Menus and Configuring Your Printer

When this selection is active, the DTR Line is used to signal the host that the
printer is powered up. This DTR Selection will not interfere with host reception
of the Xoff/Xon Serial Protocol, because unlike the Busy selection, the DTR
Signal is not toggled at the same time as the Xoff Signal. When using this
selection, the DTR Polarity Parameter must be set to Actv Hi.

If your system is configured to use Xon/Xoff Protocol, using the Busy
selection above will cause interference with printer to host communica­tion. You may however, use the DTR Line to signal the host that the
printer is Offline or that the printer is powered up (Offline and Power
selections, respectively).

DTR Polarity

This parameter is used to set the DTR Signal polarity. Active Low is the default
selection.

Busy Polarity

This parameter allows you to control the polarity of the Busy Signal. Active Low
is the default selection.

RTS Function

The RTS line of the serial interface has been used to indicate Busy in addition
to the DTR line. This option allows the RTS line to either be continuously High
or to function as Busy (default selection).

Robust Xon

This parameter behaves the same as a normal Xon/Xoff protocol, except that
with this parameter enabled, the Xon code will be sent every 5 seconds when
the printer is ready to accept data. OFF is the default selection.

3–31

Operator Manual

Parallel I/O Category

The Parallel Category on your printer has three parameters that can be
changed according to user needs.

POPC (Print On Paper Command)

The POPC Parameter can be set up so that each time a paper advance com­mand is received (such as a Line Feed, Form Feed, or Vertical Tab), any data
currently held in the buffer will be printed before the command is carried out.
The default selection is On.

8th Bit

The 8th Bit can serve several functions, depending on the software manufac­turer. Check your software manual for information concerning the functions of
this bit. Data is the default selection.

Bi-Directional

This parameter controls the bidirectional operation of the Parallel interface. The
default selection is ON (enabled).

When ON, the Parallel interface operates in IEEE-1284 Bidirectional Nibble
Mode. This mode enables features dependent on bidirectional "reverse chan­nel" communication via the parallel port, such as HP PJL Status and Windows
Plug-n-Play. Note that the host computer or print server attached to the parallel
port must be configured to use IEEE-1284 Nibble Mode, otherwise it may not
function correctly with your printer . ECP Mode is not compatible with Nibble
Mode.

When OFF, the Parallel interface operates in the Centronics Compatibility Mode
("standard" mode). This mode does not support bidirectional communication. If
there are parallel interface compatibility problems between the host computer
and the printer, setting Bi-Directional = OFF may resolve the problem.

3–32

Chapter 3: Printer Menus and Configuring Your Printer

Intellifilter Category

Intellifilter is a programmable feature, standard on TallyGenicom line printers.
Without having to touch an otherwise well-working host system, Intellifilter
permits users to free their systems from hard coded dependence on a specific
printer that is no longer maintainable, or able to meet the demands of the
application

Serial
Parallel
Twinax/Coax
LAN

These four parameters can be set to either Enable or Disable the Intellifilter on
the their respective ports.

3–33

Operator Manual

Twinax/Coax Category

Send PA (Coax Only)

There are two options for this category, PA1 and PA2. These options only
have meaning when the printer is in the SCS Mode. If they are selected while
the printer is in non SCS Mode, the Invalid Key error message will display
briefly. These options perform special functions that change from one soft­ware application to another. Selecting one of these options while the printer is
operating in SCS Mode causes the printer to:

• Display status code PA1 Key (61) or PA2 Key (62)

• Send an attention response to the host computer.

• Send a special operator request to the application program and wait

Certain application programs may ask you to select the PA1 or PA2 option in
this category. In this situation:

• The printer display will read Enter PA Key (63).

• The audible alarm beeps continuously.

• The host opens a 10 minute "window" for one of the PA options to be

for a response back.

selected. If the correct PA option is not selected during this time, the
display clears, the audible alarm stops, and the printer sends a No PA
Key message to the host computer. The effect of this message is
application-dependent. Depressing the Online/Offline key clears this
condition.

Address (Twinax Only)

Sets the Twinax device address for the printer. The default is Undefined.

SPD (Coax Only)

When set to Disabled, this parameter causes the host Set Print Density com­mand to be ignored. This is used to prevent the host from overriding control
panel CPI settings. Default is Enabled.

SCD (Twinax Only)

When set to Disabled, this parameter causes the host Set Character Density
command to be ignored. This is used to prevent the host from overriding
control panel CPI settings. Default is Enabled.

IPDS:

SLD

When this parameter is set to Disabled, the host Set Line Density command is
ignored. This prevents the host from overriding control panel LPI settings.
The default is Enabled.

IPDS:

This option is not available.

This option is not available.

3–34

Chapter 3: Printer Menus and Configuring Your Printer

Host Font Style (Twinax Only)

When you set this parameter to Disabled, the host Page Presentation Media
command is ignored. This is used when you want to prevent the host from
overriding control panel Font Style settings. The default is Enabled.

IPDS:

Screen Size (Screen) (Coax Only)

The parameter allows you to set the screen size for the Coax screen copy
function (in non SCS Mode only). The default is 1920.

Case (Coax Only)

If you set this parameter to Mono, all uppercase characters print. In Dual
mode, upper and lower case characters print. This parameter applies in non
SCS mode only. The default is Dual.

Compatibility Switches (Coax Only)

The compatibility switch settings define how the printer responds to Form Feed
(FF), Carriage Return (CR), and New Line (NL - Carriage Return plus Line
Feed) codes. The function of some of these switches depends on the end of
buffer or printing past the right margin. This parameter applies to non SCS
mode only . All comp atibility switches default to OFF.

Comp Switch 1

This switch determines the printer response to a CR Command located at the
right margin plus one character position. If OFF, the printer performs only a
CR and starts printing over the same line again without advancing the paper.
If ON, the printer performs an NL function, then begins printing.

This option is not available.

Comp Switch 2

This switch determines the printer response to an NL command located at the
maximum print position plus one character position. If OFF, the printer per­forms an NL function. If ON, the printer performs two NL functions.

Comp Switch 3

This switch determines whether or not a space is inserted at the beginning of
the first print line on each form. This switch works in conjuction with Comp
Switch 6, which determines how the printer responds to an FF command. If
OFF, the printer performs the FF and a Space function. Printing starts one
space in from the left margin on the first line of the next form.

Comp Switch 4

The settings of this switch are functional only if Comp Switch 7 is set to OFF.
Comp Switch 4 determines printer response to an FF command located at the
end of a buffer. If OFF, the printer performs an FF only. The new print location
is the first print position on the next form. If ON, the printer performs an FF
plus an NL. The print location is the first print position plus one line.

3–35

Operator Manual

Comp Switch 5

This switch determines the printer response to formatted print lines composed
entirely of unprintable characters (such as Control and Format commands). If
OFF, and the Ignore bit in the PCIA is ON, the line is not printed and no NL
function is performed. If ON, the printer prints a blank line in response to a line
of unprintable characters and performs an NL function.

Comp Switch 6

This switch determines the printer response to an FF command according to
where it is located in the data stream. If OFF, the printer performs an FF
function only if the FF command is at the first print position or at the right
margin plus one column. FF commands at any other location are treated as
blanks. If ON, the printer recognizes FF commands any time they are part of
a data stream.

Comp Switch 7

This switch determines printer response to an FF command and works in
conjunction with Comp Switch 4. If OFF, and the FF command is the last byte
in a print order, the printer responds according to how Comp Switch 4 is set. If
the FF command is not the last byte in the print data and the current print
position is not already at Column 1, the printer performs an NL function at the
end of the print job. If ON, the printer performs an FF function after each print
job if the print position is not at the top of form.

Comp Switch 8

This switch determines the printer response to a FF command in conjunction
with Compatabilty Switch 7. The default is OFF.

O FF After all the data in a print job has been printed, a NL or a FF command

is performed according to the setting of Compatability Switch 7.

ON The printer performs a FF function after an operator-initiated local copy

(e.g., a Print Screen Command from the operator). This switch over­rides Compatability Switch 7 when it is turned on.

IR Delay (Coax Only)

This parameter defines the delay from the time a fault is reported on the printer
control panel until it is reported to the host. This is used primarily to allow you
to change paper before the host cancels the print job. The default is 10 min­utes.

Hex Passthrough

When you set this parameter to On, the printer translates certain EBCDIC
character streams into ASCII escape sequence commands, and executes the
commands. Details can be found in the Twinax / Coax Applications Manual.
Default is off.

3–36

IPDS:

This option is not available.

Chapter 3: Printer Menus and Configuring Your Printer

EPC

The Early Print Complete parameter allows you to set up the printer data
buffering scheme to emulate the 4234 data-handling characteristics. When this
parameter is set to Off (the default), the printer emulates the buffering scheme
of the IBM 4234 printer, which results in standard IBM 4234 error handling.
The printer notifies the host after it is finished processing the print buffer and is
ready to accept more data. Then the host sends another buffer of up to 4K of
data. This processing mode causes short pauses during the printing process
due to the wait between notifying the host and the host sending the next buffer.

When this parameter is set to On, the printer notifies the host before it is
finished processing the print buffer. This allows faster processing because the
text buffer is set by the host before the current buffer is fully processed and
there is no delay between processing one buffer and the next buffer. This
processing mode speeds up data handling but may result in slightly different
error handling.

GrAVM (Graphics AVM)

The Graphics AVM panel menu setup option only applies to the manner in
which the Twinax AVM command is handled within a Code V, PGL, or Hex
Pass-Through graphics job.

A Tx/Cx Absolute V ertical Move (AVM) command moves the current print poition
vertically (forward only) to a line number specified by the command without
changing the horizontal print position. When the line number is less than the
current line position the line is moved to the appropriate line position on the
next page. When the line number is greater than the number of lines in the
page (form length) an invalid range parameter errors. Tally provides two re­sponses to the AVM command.

Style 1:The print position moves forward, relative to the last text item

or paper-move command that preceded the AVM command.
The new line position is calculated by subtracting the height (in
lines) of any graphic items preceding the AVM, from the line
number specified in the AVM command. This style is intended
for compatibility with printers that use an external or non­integrated Twinax interface. This is the default setting.

Style 2:The print position moves forward to the exact line number

specified by the AVM command. The presence or absence of
graphic items preceding the AVM does not affect the position
of text and/or graphics following the AVM.

3–37

Operator Manual

IPDS Category (IPDS Only)

Address (Twinax Only)

This parameter sets the Twinax IPDS device address for the printer. This
feature allows the IPDS emulation to reside at a different address than the
standard Twinax SCS emulation, hence providing two virtual Twinax printers.
The default is Undefined.

Density

This parameter defines the dot density of the IPDS output. Low is 60x72, and
High is 144x144. Medium (120x144) is the default.

Dark Bar

This parameter has three possible settings: Low , Medium, and High, with the
default being Low. This affects the print density (and print speed) of bar codes
selected through any emulation of graphics language as follows: Low (60x72),
Medium (120 half spaced x 144), and High (120 full spaced x 144). This
feature also works in conjunction with the selection of bar code density used
by Code V and PGL (Normal vs. Dark). The densities will be set based on the
previous Dark Bar selection table.

Smooth Size

This parameter defines the character size at which the block character smooth­ing algorithm is invoked. The default is 3, which means size 3 block characters
will be smoothed, but size 2 block characters will not.

Zero

Provides for the printing of open or slashed zero block character. Default is
slashed.

Host Override

The Host Override parameter gives you the option of allowing the host to
control DPI for Graphics and Bar Codes or to control Graphics and Bar Code
Density through the Control Panel. When Host Override is On, the host
controls Graphic and Bar Code DPI with the Execute Order Anystate (XOA)
command and Print Quality Control (PQC) Subcommand. When Host Over­ride is Off, Graphics and Bar Code DPI is controlled through the Control Panel
settings for Density and DarkBar parameters. The default selection is On.

3–38

Chapter 3: Printer Menus and Configuring Your Printer

TCP/IP Menu - LAN Interface Only

The TCP/IP Menu only appears if a TCP/IP LAN network interface card is
installed in the printer.

IP Addr

This option allows you to set up the four OCTETS of the IP Address.

Category Parameter

IP OCTET 1 0-255
IP OCTET 2 0-255
IP OCTET 3 0-255
IP OCTET 4 0-255

Gateway

This options allows you to set the four OCTETS of the Gateway .

Category Parameter

IP OCTET 1 0-255
IP OCTET 2 0-255
IP OCTET 3 0-255
IP OCTET 4 0-255

Subnet

This option allows you to set up the four OCTETS of the Subnet mask.

Category Parameter

IP OCTET 1 0-255
IP OCTET 2 0-255
IP OCTET 3 0-255
IP OCTET 4 0-255

Make sure that the LAN cable is attached when the printer is powered
on. If it is not, attach the cable and cycle power on the printer.

3–39

Operator Manual

Test Menu

Pattern Category

Print

In TEST Menu you will find diagnostic test print patterns used to check printer
functions and a parameter that allows you to control paper motion sensing.

Use the Up and Down Arrow keys to scroll to the desired selection. To move
down in the menu use the Up Arrow key.

The Pattern Category has a series of printer self-tests which have predefined
patterns used to test the basic printer functionality. Selection of the patterns is
done by scrolling with the Up or Down Arrow keys to the requested option, and
pressing the Enter key. The test begins based on the current margins and font
information selected. All of the panel keys are disabled while the test is
running except for the View key and the Enter and Clear keys, which terminate
the test. Once the test is terminated, all of the keys are activated.

Option Prints

Upper Rolling ASCII characters between 0x20 and 0x5E
All Characters All characters from the available character sets
63/69 63 uppercase characters followed by 69 spaces.
ECMA A pattern specified by the European Computer Manufac-

Columns Number of columns on the line, based on margin dis-

Fault Override Category

This category deals with the configuration of fault information from the Engine
Manager and the Control Processor. If the option is set to On, then the fault is
overridden and won't be reported on the panel. If the option is set to Off, then
the override is disabled and the fault is reported if it occurs.

Paper Motion

Controls paper motion fault reporting status. This setting is saved in NVRAM so
that it does not need to be set up on powerup each time.

Automatic Paper Motion Fault Retry is a feature that has been imple­mented to eliminate intermittent false paper motion faults. When a paper
motion fault is detected while printing is in progress, the paper is re­versed approximately 3 inches, then moved forward again. If the paper
motion fault persists, the printer is placed offline and the fault is re­ported. This feature can eliminate false paper motion faults caused by
random electrical noise or paper chads/dust that can be removed by the
paper reversal.

turers Association. Used for acoustic testing.

tances

3–40

Diag Category

Cal-Paper (Calibrate Paper Out)

Help Menu

Chapter 3: Printer Menus and Configuring Your Printer

This is a diagnostics and calibration category.

This parameter allows users to calibrate the paper-out detection sensor if the
factory default settings fail to detect when the paper really is out, or when false
paper-out faults occur. Pressing Enter will initiate a series of messages instruct­ing the operator to calibrate the detection sensor:

• Remove the paper from the printer, close the tractor door, and press
Enter. A numeric value will be displayed briefly. A new message appears
instructing the user to load the printer with paper.

• Press Enter. A new numeric value is displayed briefly, ending the cali­bration sequence.

There are no categories in this menu. Its purpose is to allow the user to print
out a list of all of the selected options in a single report. See at the beginning of
this chapter.

3–41

Operator Manual

3–42

Blank

Page

Appendix A

Introduction

This chapter deals with troubleshooting problems on a T6200 Series printer.
Messages that indicate printer faults and errors are explained and corrective
action given. The few paper handling and print quality problems that may
occur are also explained.

Messages

Messages on the Control Panel Display report both normal operation and fault
situations. In T able A–1 we present a listing of the Display Messages that
need explanation or action on the part of the operator or repair person. Each
message listing includes causes and corrective actions where necessary.

Faults

When a fault occurs, it will cause the printer to cease operation and go Offline.
The printer alarm will sound, the Fault Indicator will illuminate, and the display
will report a fault message.

Appendix A: Troubleshooting

In some cases it is possible to clear an error message and continue using the
printer by depressing the Clear key. However, the quality of the print may be
questionable and collateral damage to other parts may result. If the fault
message returns, perform the required corrective action.

If a nondestructive fault occurs in the middle of printing a document, one line of
text may be lost after the error condition is corrected and the printer put back
Online.

If the fault is in the control panel or interprocessor link, the fault mes­sage may not be displayed, and the beeper and Fault LED may not
operate.

Fault Correction Procedure

Step 1. First check the fault message on the Control Panel Display and look it up in the

Fault Message tables provided here.

Step 2. Perform the required corrective action. Some Fault and Error messages will

automatically clear as soon as the problem is corrected (for example, the
Platen Open message will clear when the Platen Gap Adjustment Wheel is
rotated to the proper thickness).

Step 3. If a faulty piece of hardware is indicated, call your Customer Service Represen-

tative for repair.

Step 4. If any other faults appear on the display after you have corrected the original

problem, go back to Step 1 and perform required corrective actions for the new
problem. Otherwise place the printer back Online and test it during normal
print operations.

A–1

Operator Manual

T able A–1. Display Messages

MESSAGE Explanation and Corrective Action

ATTENTION Explanation: The host has sent the Bell Command

Corrective Action: Corrective action depends on the reason the Bell Command

was sent. Contact your system operator .

Bad VFU Channel Explanation: A VFU channel command has been received from the host

requesting an illegal channel.

Corrective Action: 1. Correct data from host and retransmit.

2. Ensure the integrity of the printer ground connection.

Bad VFU Count Explanation: An incorrect number of bytes has been detected in a VFU

download.

Corrective Action: Correct data from host and retransmit.

Buffer Overflow Explanation: A buffer overflow has been detected on the currently active

host interface. This is most likely caused by a host failure
to respond to a busy signal.

Corrective Action: 1. Ensure correct protocol has been selected.

2. Check wiring of I/O cable between host and printer. (See
the Applications Manual for a detailed explanation.)

Chnl Not Found Explanation: VFU Channel requested by the host computer cannot be

found.

Corrective Action: 1. Correct data from host, then retransmit it to the printer.

2. Ensure the integrity of the printer ground connection.

Ctrl Fault Explanation: This message indicates that a fatal fault has occurred in the

control processor.

Corrective Action: Call your Customer Service Representative for repair.

Ctrl Link Flt Explanation: The Control Processor has detected a fault in the Main Pro

cessor to Control Processor link.

Corrective Action: Call your Customer Service Representative for repair.

Data Overrun Explanation: A data overrun has been detected on the currently active host

interface. This is most likely caused by an incorrectly config
ured serial baud rate, data bits, or parity.

Corrective Action: Check setting on Serial Baud Rate, Data Bits, and Parity

parameters through the printer control panel.

Font Dnld Error Explanation: An error has been detected during a font download.

Corrective Action: Correct data and retransmit from host.

Graphic Check Explanation: This message indicates that the printer has received an

unprintable graphic. This message only appears if the Set
Graphic Error Action Command has been set properly .

Corrective Action: Clear the message (Clear key), then place the printer back

Online. Confirm with host why Graphic check message was
sent.

Heap Overflow Explanation: Graphics memory space is full and the printer cannot accept

or process data. Printer will reset and data will be lost.

Corrective Action: Insert line terminators in data stream so the printer will pro

cess the data, then retransmit the data.

A–2

Appendix A: Troubleshooting

Key Disabled Explanation: Key has no function for this printer model or mode of operation.

Corrective Action: No corrective action.

Lost Adrs (27) Explanation: Certain communication signals have been lost between the

printer and the host computer.

Corrective Action: Check cable connection, setup of host, and printer address

setting.

Lost Sync (28) Explanation: The host is not communicating with the printer.

Corrective Action: Verify address of computer and host setup.

Check I/O cables.

When this message is displayed during printer
installation, you may continue to test the printer by
placing the printer Offline and entering Menu mode to
select print tests or calibration routines.

Main CPU Fault Explanation: A fault has been detected in the main processor during

powerup diagnostics.

Corrective Action: Call your Customer Service Representative for repair.

No VFU Loaded Explanation: A VFU command was received from the host before a VFU

was downloaded.

Corrective Action: Download the required VFU information, then retransmit the

data.

NVRAM Fault Explanation: The nonvolatile data checksum has failed because of one of the

following conditions:

(1 ) A new RAM has been installed
(2 ) New software with different nonvolatile variables has

been installed

(3 ) The variable values have been altered in a destructive

manner

Corrective Action: Depress the Clear Key. If the message does not clear, cycle

printer power. If the message still does not clear , call your
Customer Service Representative for repair.

Offline Data In Explanation: The printer is in Offline condition and nonprinted data is in the

buffer

Corrective Action: There is no corrective action required. Under normal

conditions, the printer continues to print when it is placed back
Online. If you do not want the buffered data to print, enter the
Clear menu by depressing the Clear key before going back
Online and select the Clear Buffers entry to clear the buffered
data.

Offline Dump On Explanation: The printer is in Offline condition and Dump Mode is enabled.

Corrective Action: No corrective action is necessary. Place the printer back

Online when you are ready to print.

Online Download Explanation: The printer is receiving downloaded fonts or VFU information.

Corrective Action: This message will clear when the download is complete

Online Dump On Explanation: The printer is ready to accept and print data from the host

through Dump Mode. All data received from the host will be
printed in hexadecimal format.

Corrective Action: No corrective action is required.

Overflow VFU Explanation: An excessive number of bytes has been sent by the host in a

VFU download.

Corrective Action: Correct data and retransmit from host.

Hammer Time Explanation: The software controlling the print hammer timing has detected

an internal inconsistency .

Corrective Action: Press the Clear key. If it fault s repeatedly, call your Customer

Service Representative and skip to the next print job.

A–3

Operator Manual

Hammer Voltage Explanation: One of the hammer drive circuits was turned on when it

shouldn't have been, so all printing has been disabled. The
usual cause is a failed drive transistor.

Corrective Action: Call your Customer Service Representative for repair.

Paper Motion Flt Explanation: The control processor has detected that the paper has failed to

move the required distance after sending a command to the
Paper Drive Motor.

Corrective Action: Check for paper feed problems. If there are any paper feed

problems, correct them, then press the Clear key to clear the
fault. If there are no paper feed problems and the condition
does not clear, call your Customer Service Represent ative.

Paper Out Explanation: Paper is not being detected by the Paper Out sensor.

Corrective Action: If this message is correct, refer to the Enter key section of

Chapter 2, then load paper. (See Loading Paper Section of
Chapter 1). If the fault does not clear, call your Customer

Service Representative.

Parity Error Explanation: Parity is enabled and a mismatch on Bit 8, between the com-

puter and the printer, has been detected on the currently active
host interface.

Corrective Action: If there is a mismatch between the setting of the printer and

the setting of the host, you can change printer parity by
referring to the Configuration Menu section of Chapter 3.

If there is no mismatch between the printer and host settings,
then the data sent from the host has been corrupted. Retrans­mit the data from the host. If the condition repeats, set up the
printer for Dump Mode (see Configuration Menu Section in
Chapter 3) and retransmit the data again. If you find no errors
in the Dump Mode data, call your Customer Service Represen­tative.

Platen Open Explanation: The Platen Gap is open beyond the maximum setting allowed

for paper thickness. This message will display when you are
loading paper or a ribbon cartridge into the printer. This condi­tion disables the printer and the only keys that will function on
the control panel are the form movement keys.

Corrective Action: When you are loading paper or a ribbon cartridge, this

message will clear when you close the Platen Gap. If this
message appears at any other time or will not clear, call your
Customer Service Representative.

Print Fault Explanation: Faulty communication between the main and control processor

has occurred causing a dot row to misprint. The printer auto­matically recovers from this condition.

Corrective Action: Under normal circumstances there is no corrective action other

than to depress the Clear key to remove the fault message from
the display. If, however, this problem persists, call your Cus­tomer Service Representative for repair .

Ribbon Fault Explanation: The Ribbon Fault Detector is not reading any movement in the

printer ink-ribbon.

Corrective Action: Depress the Clear key and try to print again. If the fault returns,

try to turn the Ribbon Knob. If the Ribbon Knob will not turn,
check to see if the ribbon is caught on the hammer bank or one
of the other mechanisms through which the ribbon moves. If the
Ribbon Knob does not turn and the ribbon is not caught some­where, install a new ribbon cartridge. If the Ribbon Knob turns

A–4

Appendix A: Troubleshooting

and the fault does not clear, call your Customer Service
Representative for repair .

Setup Address Explanation: The printer address has not been set up or a configuration

with address set to UNDEFIN has been loaded.

Corrective Action: Set up the printer address using the multilevel menus on the

printer. The procedure is located in Chapter 3, under the

Configuration Menu.

Shuttle Fault Explanation: If the control processor detects the shuttle operating either

above or below the proper frequency , it shuts down the shuttle
and attempts to restart it. If the shuttle still operates incor­rectly after three consecutive attempts, the Control Processor
goes Offline, and the Shuttle Fault message is displayed.

Corrective Action: Depress the Clear key, then put the printer back Online. If

this doesn’t work, turn the power switch off, then back on
again. If the error condition persists after performing the above
actions, call your Customer Service Representative.

Testing Hardware Explanation: The printer is performing internal diagnostic tests when the

printer is powered up.

Corrective Action: If this message does not clear after a few seconds, then the

Main CPU is dead. Under normal circumstances there is no
corrective action. If the message does not clear automati­cally , call your Customer Service Representative for repair .

Thermal Fault Explanation: The ambient temperature has exceeded the limit (Max T).

Corrective Action: Turn the printer off and allow the unit to cool. After a few

minutes, turn the power back on and retry the printer. If it
fails again, call your Customer Service Representative.

A–5

Operator Manual

Problem Cause Corrective Action

T able A–2. Paper/Printing Corrective Action

The paper holes are wider than
normal after passing through the
tractors.

Printed characters on heavy­weight or multi-part paper are
smeared.

The printed characters are too
light.

The printed characters are
shakey

The printed characters in one
line are shorter than normal.

Horizontal paper tension is too tight. Unlock and readjust the tractors.

The Platen Gap is not set correctly . Open the Platen Gap.

The Platen Gap is out of adjustment
or the ribbon is worn out.

The Platen Gap is not set correctly . Adjust the Platen Gap.

Vertical paper tension is too loose. Move the Paper Tension Lever

Readjust the Platen Gap. If this
does not correct the problem,
replace the ribbon cartridge with a
new one.

until the paper is taut but not too
tight.

The paper holes are elongated
after passing through the
tractors.

The paper comes out of the
tractors or the paper tears at the
right or left holes along the
edges.

Vertical p aper tension is too tight. Move the Paper Tension Lever until

the paper is taut

(1 ) The vertical or horizontal paper

tension is incorrect.

(2 ) The tractors are too far apart. Unlock and realign the tractors.

(3 ) Upper tractors not aligned with

the lower tractors.

(4) The Platen Gap is not set

correctly.

T o change the vertical tension,
raise the Paper T ension Lever to
increase tension, and lower it to
decrease tension.

T o change the horizontal tension,
unlock the upper right and/or lower
right tractor and move it left or right
to make the necessary adjust­ment.

Unlock and realign the tractors so
that the lower set is directly under
the upper set.

Open the Platen Gap.

A–6

Specifications

Emulations

The emulations available on your printer are: MT660, Printronix P600,
Printronix P6000, Printronix P5000, Epson FX-1180, IBM Proprinter III XL, IBM
4234 (Twinax and Coax), IBM 4210 and 5225 (Twinax Only), DEC LG01,
HP2564C, MTPL, Genicom ANSI, PJL, Code V, PGL, IPDS.

T ype Style

There are six resident type styles available on your printer. They include
Gothic, Courier, Data Processing, Draft, OCR-A, and OCR-B. All type styles
and the two output modes (for Draft and DP) are selectable through the printer
control panel.

Gothic and Courier

These two type styles provide Near Letter Quality (NLQ) printing. They print
at higher dot densities and use denser character matrixes for greater readabil­ity.

Specifications

Draft and Data Processing

Draft and Data Processing type styles print in two modes: Constant Density
Fonts (CDF) and Enhanced.

Constant Density Fonts print at the same dot density regardless of the CPI.
This produces consistent print speed even when changing from one CPI to
another.

Enhanced Mode provides higher resolution and a greater range of CPIs than
CDF Mode. Because Enhanced Mode uses a variety of dot densities you
should expect a change in print speed of text when switching from one CPI to
another.

OCR–A and OCR–B

These print at 10 CPI only, mostly for Optical Character Recognition applica­tions.

Characters Per Inch

Your printer offers a variety of CPIs for use in printer output. Available CPIs
are dictated by the Type Style selected. Each CPI is based on one of 12
character matrixes and 12 Dot Densities. Each matrix uses a specific number
of dot columns for character composition and intercharacter gap. CPIs are
grouped in any given type style by the base CPI matrix used for the group.
Those Base CPIs are 10, 12, and 15.

S–1

Operator Manual

Densities and Throughput

Your printer supports Horizontal row plots (single and multiple row), Vertical column
plots, and specialized Graphic plots.

Your printer supports the following horizontal DPIs: 40, 48, 60, 80, 90, 120, 180, and

240. Scaled densities available on your printer are 50, 72, 75, 96, 100, 144, 150,
160, and 200. All other selections will be approximated by conversion to the next
higher density.

Your printer supports the following vertical DPIs: 48, 72, 96, 144, and 288. All other
selections are emulated through the use of scaling techniques.

Text Throughput - Lines per Minute T6218 T6215 T6212
Upper Case / Lower Case

Draft 10 CPI 1800/1500 1500/1285 1200/1000

Data Processing 10 CPI 1350/1080 1 125/900 900/720

Gothic 10 CPI 720/600 600/500 480/400

Graphics Throughput - Inches per Minute

60 X 48 225 187 150
60 X 72 150 125 100
120 X 72 DPI 75 62 50

Application Benchmarks

AIAG 2-up Normal/PGL - Label/Hrt 4392 3660 2928
AIAG 2-up Read/Right/PGL - Labels/Hr 2788 2460 1968
POSTNET 6LPI Labels/Hr Draft 70,266 62,000 49,600

ECMA 132 - Pages Per Hour

#2 Letter Performance 10 CPI Draft 1864 1645 1316
#3 Letter Performance 10 CPI NLQ 878 775 620
#4 Letter Endurance 10 CPI NLQ 8 84 780 624
#5 Spreadsheet Perf. 17 CPI Draf t 2493 2200 1760
#6a Spreadsheet Perf. 17 CPI Draft 2493 2200 1760
#6b Spreadsheet Perf. 17 CPI NLQ 994 780 624

#7 Graphics Performance 1 1 22 990 792

Table S–1 Text Performance

15 CPI 1800/1500 1500/1285 1200/1000

17.14 CPI 1800/1500 1500/1285 1200/1000

15 CPI 1350/1080 1 125/900 900/720

17.14 CPI 1350/1080 1 125/900 900/720

15 CPI 540/450 450/375 360/300

17.14 CPI 540/450 450/375 360/300

S–2

Lines Per Inch

Ten Lines Per Inch (LPI) settings are available through the Control Panel.
They include 1.5, 2, 3, 4, 5, 6, 8, 9, 10, and 12 LPI. In some emulations the
availability of certain LPIs is restricted.

Paper Movement Speed

Your printer has a normal slew speed of 36 inches per second. When printing
in Heavy Forms mode, the maximum slew speed is decreased to 20 inches
per second.

Languages and Character Sets

Up to 34 Language Character Sets with up to 192 characters (some emula­tions have fewer character sets with 256 characters) each are available on
your printer. In addition, the ANSI and DIN character sets are available for
use with the OCR-A and OCR-B type styles.

With the exception of ANSI and DIN, the language character sets can be
printed in four different type styles: Gothic, Courier, Data Processing, and
Draft. The ANSI and DIN characters can only be used with the OCR-A and
OCR-B type styles and are selectable in four combinations through the Printer
Control Panel.

Specifications

Physical Configurations

Your printer only is available enclosed in a quietized cabinet.

Weight

Your printer has an actual weight of 185 lbs. (84 kg) and a shipping weight of
212 lbs. (96 kg).

Paper Description

The printer uses continuous, sprocket-fed type paper, 2.5 inches (64 mm) to
18 inches (457 mm) outside width and 3.0 inches (76 mm) to 12.0 inches (305
mm) in length. One- to six-part paper may be used with a maximum thickness
of .025 inches (0.64 mm). (Reference specifications: ISO 2784, DIN 9771
and DIN 6721.)

Acoustics

The Sound Power of your printer is 6.7 Bel (9 position average, per ISO 7779)
with a Sound Pressure Level of less than 52.0 dBA (4 position average, per
ISO 9296).

Nonvolatile Memory

Your printer stores up to 10 printer configurations in nonvolatile EEPROM.

S–3

Operator Manual

Power Supply

The printer requires single phase, 47 to 63 Hz. 90 to 264 VAC input power.
The printer’s universal power supply automatically adjusts to the correct
values. A fuse is provided to interrupt power to the power supply. The follow­ing table gives typical current values.

Table S–2. Power Requirements

External Power Current/Wattage Requirements @ Nominal
Voltage

Supply

AC Volts Freq. Average Peak Average Average
(RMS) (Hz) Operating Operating Idle (<5 min.) Idle (>5 min.)

1 10 50 2.0 A/215 W 5.5 A/600 W 0.5 A/55 W 0.3 A/30 W

1 10 60 2.0 A/215W 5.5 A/600W 0.5 A/55W 0.3 A/30 W

220 50 1.0 A/215W 2.8 A/600W 0.3 A/55W 0.2 A/30W

Preventive Maintenance

This printer is designed to eliminate the requirement of scheduled mainte­nance procedures, such as alignment, adjustment, or lubrication. Preventive
maintenance is limited to periodic cleaning. Dust and paper fibers should be
removed periodically with a soft cloth and brush or a vacuum cleaner. Clean
the printer case with a damp cloth and soapy water. DO NOT use any abra­sive cleaners or solvents, as they will damage the case.

Safety

Personnel hazard areas have restricted access with appropriate warning
labels. Catastrophic equipment failures are inhibited with protective functions
in major areas of overload potential.

Cooling System

Cooling system malfunctions are detected and a failure will result in shuttle
motion, paper motion, and printing functions being inhibited. The malfunction
will be reported on the control panel display.

S–4

Environment

Operating

Nonoperating

Specifications

Temperature
Dry Bulb: 50°F to 104°F (10°C to 40°C)
Humidity: 10 to 90% noncondensing with a maximum wet bulb

temperature of 82°F (28°C) and a minimum dew point of
36°F (2°C )

Altitude: To 8,000 ft. (2438 meters)

Temperature:

Boxed: -40°F to 151°F (-40°C to 66°C)
Unboxed: 14°F to 122°F (-10°C to 50°C)

Humidity: 10 to 95% noncondensing
Altitude: To 10,000 ft. (3048 meters)
Thermal Shock: 61°F (20°C) per hour
Vibration: Units meet NSTA (National Safe Transit Association)

Heat Load Contribution

The average heat load contribution to the environment is approximately 735
BTUs per hour (215 Watts). The minimum heat load contribution is approxi­mately 100 BTUs per hour (30 watts). The maximum is 2050 BTUs per hour
(600 Watts), under continuous full-load printing conditions.

Printing Conditions (110 VAC/60 Hz) Wattage BTU/Hr

Power On, not printing 55 W 188
100% Uppercase Rolling ASCII 400W 1370

requirements.

Table S–3. Heat Load Contributions

Black Page Plot 600 W 2050

S–5

Operator Manual

Printer Dimensions

Top Vi ew

28.8 in.

(731.5 mm)

28.3 in.

(718.8 mm)

Back (and Front) View

62.2 in.

(1579.9 mm)

40.0 in.

(1016.0 mm)

Side View

Figure S-1. Physical Dimensions

S–6

Industry and Agency Standards.

The T6200 Series is designed to meet the requirements of several industry and
government agency standards.

Electro-Magnetic Emissions

EMI: FCC part 15, subpart J, Class A

and EN55022 Class B
Harmonics: EN 61000-3-2
Flicker: EN 61000-3-3

Electro-Magnetic Immunity

ESD: EN 61000-4-2
RF EMF: EN 61000-4-3
EFT/B: EN 61000-4-4
Surge: EN 61000-4-5
RF CM: EN 61000-4-6
PF MF: EN 61000-4-8
V Dips/Int: EN 61000-4-11

Specifications

Energy Conservation

ENERGY STAR® compliant

Safety

IEC 60950:1991plus Amendment 1, 2, 3, and 4, and National
Deviations AT, AU, BE, CA, CH, CZ, DE, DK, ES, FI, FR, GB,
GR, HU, IE, IT, JP, KR, NL, NO, SE, SG, SL, US and Group
Differences per CB Bulletin 94AI(Mar 99).

ANSI UL 1990-95, CAN/CSA-C22.2 No. 950-95, and
EN6950:1992, including Amd 1, 2, 3, and 4 safety require­ments.

Acoustic

ISO 7779:1988(E)
ISO 9296:1988(E)

Marking

The printer complies with the CE mark requirements, per
European norms.

S–7

Operator Manual

255025-001A

S–8

Blank

Page