Tait T800 II Reference Guide

T800 Series
Conventional Equipment

II

Reference

M800RACK-00-101

Guide

T800 Series II Conventional Equipment

Index

Section 1: Introduction

Guide to the Conventional T800 Equipment Questionnaire
Conventional T800 Equipment Questionnaire
Order Number System
Rack and Function Cross-Reference Chart

Rack Components Weights
Section 2: Rack Configurations
Section 3: Rack Power Supply Options

Section 4: Guide Assemblies (Pending)
Section 5: Rack Backplanes (Pending)
Section 6: Personality Boards (Pending)
Section 7: Ancillary Modules (Pending)
Section 8: Modules (Pending)

3/7/00

T800 Series
Conventional Equipment

Reference Guide

II

Introduction

T800 Series II Conventional Equipment Section 1

T800 Conventional Equipment

This publication contains relevant reference information for Tait’s T800 Conventional
product range. It will be updated as equipment is modified or new features are
introduced.

It is intended to show only standard options. There is provision to ‘mix & match’ up to
seven modules in a rack to produce combinations for customised solutions.

Tait System Solutions are open-ended.

As well as information about the equipment there is also an order form and detailed
instructions on how to fill in the orde r form.

If you cannot find a solution,

Please contact Custom Solutions.

Contact Details

Chris Quinlivan Conventional Systems Manager
Alana Mehrtens Technical Illustrator

535 Wairakei Rd
PO Box 1645
Christchurch
New Zealand

Telephone: (64) (3) 3583399
Facsimile: (64) (3) 358 2825
E-mail: [e-mail]

Copyright TEL 3/7/00

T800 Series II Conventional Equipment Section 1

Document Control

The initial release o f this guide will be a hard copy delivered to Customer Service
Organisations and other relevant people within the Tait organisation.

In the interests of im proving the performance, reliability or servicing of the
equipment, Tait Electronics Limited reserve the right to update the equipment or this
document or both without prior notice.

The Master copy will be available on the Tait Ele ctronics Ltd Customer Service web
site.

Changes will be notified to all document holders who will be responsible for updating
these changes from the web site.

Copyright TEL 3/7/00

Guide and Purpose

for

Conventional T800 Equipment Questionnaire

The purpose of this questionnaire is to assist the staff of TEL to get as much
information as possible from you at the start of your enquires or order request
for equipment that is to be SET-UP BY TEL. The accurate completion of this form
will speed up processing time and ensure delivery of the correct equipment.

PART 01. (WHAT IS REQUIRED)

This is to immediately identify the quantity and what sort of configuration or equipment is
required.

PART 02. (FREQUENCY BAND REQUIRED

This is to indicate which frequency band the equipment is required to operate in. It also gives the
equipment type required.( for Series I the last four digits are not needed). In some cases there will
be a need for Transmitter and Receiver to be in different bands; this will not affect the Rackframe
required.

ENSURE EQUIPMENT STATED IS TYPE APPROVED FOR COUNTRY OF USE.

PART 03. (DO YOU KNOW WHAT IS REQUIRED)

The completion of this section in full is not always essential but the more information you
provide will assist the Technician in correctly configuring the Rackframe to your requirements.

SPEAKER PANELS ARE FITTED AS STANDARD WHERE APPROPIATE

In the Rackframe line for part number you may put the code for the configuration required, these
codes can be found in the T800 Series II Conventional Equipment Reference Guide, Section 1. If
you do not have an TEL code, you may enter either the high level T number, if known. These are
also in the Reference Guide, Section 2, or enter “do not know” and leave the selection of
Rackframe to TEL who will select the appropriate configured Rackframe to meet your
requirements, based on the rest of the information provided in this section.
For the rest of the requirements, indicate the quantities required in the appropriate box for the
module that you would like to be fitted into the Rackframe, remembering there is only
sufficient room to fit 7 x 60mm modules. Doing this will help TEL ensure that
if a Rackframe has been mentioned it can support your requirements. If no standard
Rackframe exists that will fulfil your needs, then TEL can engineer a configuration to satisfy
your requirements.

T800questV13.doc : Issued 6 July 2000 Page 1 of 2

PART 04 (EQUIPMENT TYPE REQUIRED)

This is to indicate the preferred type of equipment you require, remembering that eventually all
types will be Series II. Ensure type ordered are Type Approved for Country of use.

PART 05 (DO YOU KNOW THE FREQUENCIES)

This information can be helpful as sometimes the auxiliary equipment can be
frequency-dependent, ie; Duplexer/Splitters, etc.

PART 06 (AUXILIARY EQUIPMENT)

The information provided in this section ensures that the auxiliary equipment asked for is
appropriate for the frequency band that the rest of the equipment is to operate in.

PART 07 (ANCILLARY EQUIPMENT)

This section is to advise TEL of the maintenance support equipment required.

PART 08 (BRIEF DESCRIPTION)

This section is to enable you to give TEL a quick operational requirement and provide sketches if
deemed necessary on the information sheet provided.

PART 09 (ADDITIONAL COMMENTS)

This section is to allow you to provide any extra information you think TEL will require.

PART 10

This is to inform TEL of your required delivery DATE .

PART 11 (TRANSMITTER/EXCITER PARAMETERS)

This section is to allow you to inform TEL of operational parameters for the equipment.

By ticking the STANDARD box you are indicating that all parameters required are as stated in
the Set-up procedure in the appropriate equipment manual, and the frequency/frequencies
required are as stated in PART 05. If no frequencies are stated in Part 05 then the equipment is to
be Set-up on TEST frequencies.

By ticking the CUSTOMISED box you are indicating special requirements are needed. You must
then fill in all the required details in the boxes below to allow TEL to set-up the equipment to
those specifications and options, and to supply any other information that may be required by
TEL.

PART 12 (RECEIVER PARAMETERS)

Same as above.

T800questV13.doc : Issued 6 July 2000 Page 2 of 2

CONVENTIONAL T800 EQUIPMENT

Customer Information: Date:

Customer / C.S.O
From:
Purchase Order Number:
TEL Quote Reference:
TEL Staff Responsible:

This form has been devised to assist in clearly identifying the Product required, and i t s
operational parameters if being BUILT and TESTED by TEL.

DO YOU REQUIRE RACKS and MODULES? DO YOU REQUIRE MODULES ONLY?

(Please continue on this page) (TEL to Set-up, Please go to PART 04)

PART 01. WHAT IS REQUIRED?

Base Station Portable Slimline To Operate as a Repeater Yes No

TOTAL QUANTITY REQUIRED :-

PART 02.

66- 88Mhz
136-156Mhz
148-174Mhz
174-225Mhz

FREQUENCY BAND REQUIRED ?

(T82n-xx-xxxx)
T83n-xx-xxxx)
(T83n-xx-xxxx)
(T37n-xx )

220-244Mhz
243-270Mhz
330-380Mhz
400-440Mhz

(T86n-xx-xxxx)
(T86n-xx-xxxx)
(T87n-xx-xxxx)
(T85n-xx-xxxx)

440-480Mhz
480-520Mhz
800-880Mhz
870-960Mhz

(T85n-xx-xxxx)
(T85n-xx-xxxx)
(T88n-xx-xxxx)
(T88n-xx-xxxx)

ARE REQUIRED MODULES TYPE APPROVED,

PART 03.

DO YOU KNOW WHAT IS REQUIRED PER RACK?

Description Option Required

COUNTRY OF USE :-

Qty

( / Rack)

Part Number

Total

(Qty x No of racks)

Rackframe
Receiver
Transmitter
Exciter

Power Amplifier

Power Supply
Converter

Circuit Breaker

10Amp, 20Amp or 30Amp

50 Watts

70 / 100 Watts

AC for Volts

External 13.8V Supply

Battery

12/12, 24/12, 48/12

Alarm Unit
Monitor Unit
Tone Remote
Combiner 200W
Hi Stability Osc
Channel Panel
Cooling Fan

10 Channel / 100 Channel

Single or Double

Relay-50 W Max
Duplexer
Duplexer Cradle
Blank Panel
Speaker Panel

Tx/Rx Frequencies required

(T800-42-0001)
(316-06615-00)

Single/selectable

Option

T800temp.V13.doc : Issued 14/07/00 Page 1 of 4

Purchase Order Number

PART 04. EQUIPMENT TYPE REQUIRED :-

PART 05. DO YOU KNOW THE FREQUENCIES AT THIS TIME?

SERIES I SERIES II

No To be advised Attached

Yes

Tx MHz CTCSS Hz
Rx MHz CTCSS Hz

Channel Panel Eprom Info To be advised Attached

PART 06.

Description OPTION REQUIRED Qty Part Number

Automatic

Changeover

Unit

PART 07. ANCILLIARY EQUIPMENT :-

Module Extender with 2 D Ranges(standard)

Module Extender with 11 way D Range(QS)

AUXILLIARY EQUIPMENT :-

For Freq:- Mhz

Power Monitor Kit

Installation Kit

Description Qty Part Number

Cabinet

Microphone

Programming Software

Service Manuals

PART 08.
BRIEF DESCRIPTION : (Diagram / Information Sheet Attached?)

PART 09.
ADDITIONAL COMMENTS :-

PART 10.

DATE REQUIRED

Yes No

T800temp.V13.doc : Issued 14/07/00

Page 2 of 4

Purchase Order Number

PART 11.
TRANSMITTER/EXCITER PARAMETERS :- STANDARD CUSTOMISED

(As Manual) (Identify Requirements)

Channel Spacing : C.T.C.S.S. :

12.5 kHz No

20.0 kHz Yes

25.0 kHz Single

Other kHz (Freq Hz)

Frequency Stability : (VHF) 2.5 ppm Multiple

1.5 ppm (Pattern Required)
(UHF) 1.0 ppm Tx Time Out :
External Reference Disabled

Transmitter Power : Enabled

25 Watts (Max Time 5 mins) Duration Mins
50 Watts Tx Tail Time :

(For 800MHz Max 70W) 70 Watts Disabled

100 Watt s Enabled

Other Watts (Max Time 5 secs) Duration Secs

Number of Channels : Audio Response :

Single Pre-emphasised

(Freq MHz) Flat

Multiple Special Modifications

(Pattern Requir ed) No

Yes

Line Level : dBm Refer to Part 08

PART 12.

RECEIVER PARAMETERS :- STANDARD CUSTOMISED

(As Manual) (Identify Requirements)

Channel Spacing : C.T.C.S.S. :

12.5 kHz No

20.0 kHz Yes

25.0 kHz Single

Other kHz (Freq Hz)

Frequency Stability : (VHF) 2.5 ppm Multiple

1.5 ppm (Pattern Required)
(UHF) 1.0 ppm
External Reference Audio Response :

Number of Channels : De-emphasised

Single Flat

(Freq MHz)

Multiple R.S.S.I. : (UHF Equipment Only)

(Pattern Required) Note:All other equipment No

has RSSI as standard Yes
Special Modifications

Line Level : dBm No

Yes

Gating Operating Level : Refer to Part 08

T800temp.V13.doc : Issued 14/07/00

Page 3 of 4

Purchase Order Number

SYSTEM BLOCK DIAGRAM (OPTIONAL)

T800temp.V13.doc : Issued 14/07/00

Page 4 of 4

T800 Series II Conventional Equipment Section 1

T800SII Numbering System

Conventional Rack Systems ordered from RSD using the adjacent Numbering
System will be configured as follows:

Rack Configuration

The Racks used in these configurations are as per Section 2 of this guide, which
illustrates the factory default sp ecifications.

Each Rack is fully wired and set-up for AC or DC power supply options.
(Refer to Section 3).

A Speaker / Programming Port Panel and all required Blank Panels and are fitted as
standard to each rack as required. Receiver, transmitter, PA, power supply, etc.
must be ordered separately.

If the System Type is code “B”, a co-axial relay is fitted as standard. If any other
code is used, then relays must be requested if required.

Module Configuration

All Rx and Ex/Tx modules are fitted with second D-ranges as Standard.
ie.(T8XX-XX-0200)

All technical information on this Rack configuration is available from RSD.

Copyright TEL 3/7/00

Order Number System

14/12/1999

System

Type

Frequency

Band

RF Output

Power

Channel
Spacing

Power

Supply

Duplexer

B A 1 W D 0 0

B =

Base Station

R =

Repeater

S =

Slimline

P =

Portable

T =

Tone Remote

D =

Dual Base

Q =

Quasi-Sync

H =

HSO Rack

L =

Liberty

A =
B =
C =
D =
E =

F =
G =
H =

I =

J =

K =

L =

66 - 88
136 - 156
148 - 174
400 - 440
440 - 480
480 - 560
800 - 880
870 - 960
220 - 244
243 - 270
265 - 285
330 - 380

(T800-22-XXXX)
(T800-22-XXXX)
(T800-23-0000)
(T800-25-XXXX)
(T800-27-XXXX)
(T800-22-001X)
(T800-24-XXXX)
(T800-28-XXXX)
(T800-56-XXXX)

(T82x-xx)

MHz

(T83x-1x)

MHz

(T83x-2x)

MHz

(T85x-1x)

MHz

(T85x-2x)

MHz

(T85x-3x)

MHz

(T88x-1x)

MHz

(T88x-2x)

MHz

(T86x-1x)

MHz

(T86x-2x)

MHz

(T86x-3x)

MHz

(T87x-2x)

MHz

N =

12.5 kHz

M =

20 kHz

W =

25 kHz

E =

50 kHz

A =

Power Supply

(T807-10-0000)
(T808-10-0000)

B =

Slimline Power Supply

D =

DC External Power supply

0 =

No Duplexer Fitted

1 =

50 Watt Duplexer Fitted

2 =

Coaxial Relay

This item code is always set to (0)
for Slimline configurations.

If Duplexer item code is set to (1),
then Base/Repeater/Slimline
Requirement sheet must be
completed.

(T807-23-0010)

Ancillary

Options

1 =

25 Watts

2 =

50 Watts

3 =

90 or 100 Watts

4 =

5 Watts

Example: BA1WD00

B =

Base Station

A =

66 -88 MHz

1 =

25 Watts

W =

25 kHz

D =

DC External Power supply Fitted

0 =

No Duplexer Fitted

0 =

No Ancillaries Fitted

0 =

No Ancillary Option

1 =

Circuit Breaker Panel

2 =

Tx/Rx Metering & Monitor Unit

3 =

Multi-Channel Panel (100 CH)

4 =

Multi-Channel Panel (10 CH)

5 =

Alarm Module

Excellence in Radio

Receiver

Communications

T800//

T800//

Sensitivity

Volume

Gating

Gate

Supply

Line
level

Monitor

Off
On

Monitor

Mute

Excellence in Radio

Transmitter

T800//

On

Carrier

Line

Supply

Sensitivity

Microphone

Excellence in Radio

Communications

Communications

T800//

T800//

T800//

Speaker Panel

T800//

Excellence in Radio
Communications

Equipment list
T825-10-0200

T826-10-0200

(T800-17-00XX)
(T818-01-0000)
(TA087-01-0000)
(TA387-01)
(TA136-02-0000)

T800-22-0000
This set-up comes complete

with all required Blank Panels
and a Speaker/Programming
Panel

Rack and Function Cross-Reference Chart

Relevant

Module

T number

T8n6 -

T8n7 - T8n7 -

T8n7 - T8n7 -

Cross-

Reference

Section

2

8

8

8

Module Function

Single system

Dual system

Receive only

Transmit only
25W Transmit
50W Transmit

100W Transmit

T800 - 22 - 0x00

2

2

2

2

2

2

2

2

T800 - 22 - 0x06

2

2

2

2

T800 - 22 - 0x10

2

2

2

2

2

2

2

2

T800 - 22 - 0x11

2

2

T800 - 22 - 0x12

2

2

Superceded by T800-22-0x16 T800 - 22 - 0x13

T800 - 22 - 0x14

2

2

2

2

T800 - 22 - 0x15

2

2

2

2

T800 - 22 - 0x16

2

2

2

2

Superceded by T800-22-0x14 T800 - 22 - 0x17

T800 - 22 - 0x18

2

2

2

2

2

2

T800 - 22 - 0x20

2

2

2

2

2

2

2

2

T800 - 22 - 0x21

2

2

2

2

T800 - 22 - 0x22

2

2

2

2

T800 - 22 - 0x23

2

2

2

2

2

2

T800 - 22 - 0x24

2

2

2

2

2

2

T800 - 23 - 0000

2

2

2

2

T800 - 23 - 0001

2

2

2

2

T800 - 23 - 1001

2

2

2

2

All Power options

power options

7

Changeover interface

8

7

7

7

8

8

Circuit breaker

Optional Duplexer

Optional relay

Optional CH/PNL

T803 Remote/Alarm

Alarms (TA136)

Limited

Converter

Portable

Quasi Sync

Ext
DC

2

2

AC

AC

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

0
1
3

2

2

2

2

2

2

2

2

2

2

2

2

0
2

1

3

4

5

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

1
4

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

8

8

8

Monitor (T818)

Fylde TSC Interface

Speaker

Paging

Slimline

14/07/2000

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

Module Function

Single system

T800 - 24 - 0000

2

2

T800 - 24 - 0x01

Rack and Function Cross-Reference Chart

T800 - 24 - 0x02

T800 - 24 - 0x03

T800 - 24 - 0600

T800 - 24 - 0601

T800 - 25 - 0000

T800 - 25 - 0001

T800 - 25 - 0002

T800 - 27 - 0x00

T800 - 27 - 0x01

T800 - 28 - 0x00

T800 - 29 - 0x00

T800 - 29 - 0x01

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 - 29 - 0x02

Dual system

Receive only

Transmit only
25W Transmit
50W Transmit

100W Transmit

All Power options

Limited

power options

Converter

Changeover interface

Circuit breaker

Optional Duplexer

2

2

2

2

2

2

2

Ext

DC,

Bat

2

2

2

2

2

AC,
DC,

Bat

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

AC,

DC

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

Power Options

AC only

0

External DC only

1

2

2

2

2

2

2

2

2

2

2

1
4

2

2

2

2

2

2

AC and External DC

2

AC and Battery

3

External DC and Battery

4

AC, External DC and Battery

5

Optional relay

Optional CH/PNL

Portable

T803 Remote/Alarm

Quasi Sync

Alarms (TA136)

Speaker

Monitor (T818)

Paging

Fylde TSC Interface

Slimline

14/07/2000

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

T800 SeriesII Rack and Module Weights

Weight (kg)

Rackframe

to house 2 modules 3.60
to house 3 modules 4.15
to house 4 modules 4.70
to house 5 modules 5.25
to house 6 modules 5.80
to house 7 modules 6.35

T8n5 Receiver 2.20
T8n6 Transmitter 2.05
T8n7 Exciter 2.05

50W Power Amplifier 3.20
100W Power Amplifier 3.55

T80n Power Supply 2.30
Circuit breaker 0.50
DC Converter Module 0.90

0.00

TA136 Alarm Unit 0.85
T818 Monitor 0.95
TA807 Channel Panel 0.35
TA320 Combiner 2.80
Duplexer 1.15
Duplexer Cradle 0.55
T803 Tone Remote / Alarm 1.55
T801-20 High Stability Oscillator 1.50

Portable Repeater Case

to house 3 modules (Standard) 6.00
to house 4 modules 6.15

2 Batteries (Standard) 5.60

14/07/2000

T800 Series
Conventional Equipment

Reference Guide

II

Rack

Configuration

T800 Series II Conventional Equipment Section 2

T800-22-0x00

A standard single channel rack for repeater or base station use; up to 100 Watt
output.

Operational Characteristics

• Single channel

• Up to 100W with option of Transmitter or Exciter / PA combination

• Speaker / Programming panel

• DC line fuse

• Earth stud

• Backplane interface

Power Supply Options

• x = 0 AC only

• x = 1 External DC only

• x = 2 AC and External DC

• x = 3 AC and Battery

• x = 4 External DC and Battery

• x = 5 AC and External DC and Battery

Configuration Options

• Duplexer

• Coaxial Relay

• Fans - single or double

• Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0010

installation kit

• microphone

• DC converter

Mechanical Characteristics

• 5 Rack Units x 19” rack to house up to 7 modules

• Size

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

• Weight – (rackframe with modules shown)
25W - 11.25kg
50W - 14.45kg
100W - 14.80kg

NOTE:

solutions for specific req uir em ent s.
Refer to RSD for design and build of personality boards.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

This product offer s t he versat ility of fitting personality boards to pr ovide custom ised

Copyright TEL 3/7/00

FRONT VIEW

T800//

Excellence in Radio
Communications

Power
Supply

T800//

Receiver

Gating

Gate

Sensitivity

Supply

Line
level

Monitor
Volume

Off
On

Monitor

Mute

Speaker

Panel

Exciter

T800// T800//

Carrier

Line

Sensitivity

Microphone

OPTIONAL

TRANSMITTER

Supply

On

Power Amplifier

FAN (OPTIONAL)

OPTIONAL

BLANK

REAR VIEW

Excellence in Radio
Communications

Supply

Low forward power

High reverse power

Power

T800//

OPTIONAL

DUPLEXER

PA ReceiverExciter

T800//

Speaker Panel

Power Supply

T800//

Overload

Standby

On

OPTIONAL

BLANK

Power

1
2
3

+

4

-

5

FAN (OPTIONAL)

EARTH

STUD

Output

13.8V
25A
Max.

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

T800-50-0000

FUSE

QTY

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED
1T800-41-0002 DOUBLE GUIDE KIT
1T800-45-0000 GUIDE PA 50W KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-15-0000 SPEAKER / PROGRAM PANEL
1T800-40-0000 FIXING KIT ONLY
2T800-40-0001 BLANKING BRACKET / FRONT PANEL
1T800-50-0000 BACKPLANE
1X800-90-0000 POWER RAIL (STANDARD)

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

TB1

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 4
SECTION 8
SECTION 4
SECTION 8
SECTION 5
SECTION 3

T A I T

Radio Communications
Christchurch
New Zealand

5

Drawing name changed

Drawing No changed and Ref. added

4
3

Parts list added

2

Change of Title

1

Original

Version

AMM 26/11/99ABB
AMM 24/8/99ABB
AMM 8/3/99ABB
AMM 14/12/98ABB
AMM 22/10/98ABB

Drawn DateChecked

TITLE:

RACK, SNGL<100W, (OPT BD

DRAWING:

T800-22-0x00 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-22-0x06

A 25 Watt single channel rack for repeater or link use.

Operational Characteristics

Single channel

•

Up to 25W Transmitter Output

•

Speaker / Programming panel

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

•

Configuration Options

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0010

•

installation kit

Microphone

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

7.85kg

NOTE:

This product offers the versatility of fitting personality boards to provide
customised solutions for specific requirements.
Refer to RSD for design and build of personality boards.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

T800//

Excellence in Radio
Communications

T800//

Excellence in Radio
Communications

T800//

Excellence in Radio
Communications

T800//

Speaker Panel

REAR VIEW

ReceiverTransmitter

Speaker

Panel

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Supply

Off
On

On

Excellence in Radio
Communications

T800//

OPTIONAL

POWER

SUPPLY

Transmitter

T800//

Gate

Carrier

Line

Sensitivity

Microphone

Supply

T800-50-0000

EARTH

STUD

DC INPUT FUSE

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

QTY

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED
1T800-41-0002 DOUBLE GUIDE KIT
1T800-15-0000 SPEAKER / PROGRAM PANEL
1T800-40-0000 FIXING KIT ONLY
4T800-40-0001 BLANKING BRACKET / FRONT PANEL
1T800-50-0000 BACKPLANE
1X800-91-0005 POWER RAIL (STANDARD)

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

TB1

REFERENCE

SECTION 4
SECTION 4
SECTION 8
SECTION 4
SECTION 8
SECTION 5
SECTION 3

T A I T

Radio Communications
Christchurch
New Zealand

3

Parts list amended

3

Optional power supply added

Drawing No changes and Ref. added

2
1

Original

Version

AMM 28/1/00ABB
AMM 22/12/99ABB
AMM 24/8/99ABB
AMM 19/2/99ABB

Drawn DateChecked

TITLE:

DRAWING:

RACK, RPT/LK 25W

T800-22-0x06

T800 Series II Conventional Equipment Section 2

T800-22-0x10

A single channel repeater or base station rack based on the standard T800-22-0x00,
with the option of fitting a Channel Panel.

Operational Characteristics

Single channel

•

Up to 100W with option of Transmitter or Exciter / PA combination

•

Speaker / Programming panel

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

•

Configuration Options

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

•

installation kit

microphone

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Length - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

25W - 11.25kg
50W - 14.45kg
100W - 14.80kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

T800//

Excellence in Radio
Communications

Power

Supply

T800//

Receiver

Gating

Gate

Sensitivity

Supply

Line
level

Monitor

Volume

Off
On

Monitor

Mute

Speaker

Panel

Exciter

T800// T800//

Carrier

Line

Sensitivity

Microphone

OPTIONAL

TRANSMITTER

Supply

On

Power Amplifier

OPTIONAL

BLANK

REAR VIEW

Excellence in Radio
Communications

Supply

Low forward power

High reverse power

Power

FAN (OPTIONAL)

T800//

OPTIONAL

DUPLEXER

PA ReceiverExciter

Speaker Panel

T800//

OPTIONAL
CHANNEL

PANEL

Power Supply

T800//

Overload

Standby

OPTIONAL

BLANK

On

Power

1
2
3

+

4

-

5

FAN (OPTIONAL)

EARTH

STUD

Output

13.8V
25A
Max.

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

FUSE

T800-50-0001

QTY

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED
1T800-41-0002 DOUBLE GUIDE KIT
1T800-45-0000 GUIDE PA 50W KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-15-0000 SPEAKER / PROGRAM PANEL
1T800-40-0000 FIXING KIT ONLY
2T800-40-0001 BLANKING BRACKET / FRONT PANEL
1T800-50-0001 BACKPLANE CH-PNL
1X800-90-0000 POWER RAIL (STANDARD)

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

TB1

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 4
SECTION 8
SECTION 4
SECTION 8
SECTION 5
SECTION 3

T A I T

Radio Communications
Christchurch
New Zealand

5

Drawing name changed

4

Drg No changed and Ref added

3

Parts list added

2

Change of Title

1

Original

Version

AMM 26/11/99ABB
AMM 25/8/99ABB
AMM 8/3/99ABB
AMM 14/12/98ABB
AMM 21/10/98ABB

Drawn DateChecked

TITLE

DRAWING:

RACK, SNGL<100W, (CH PNL

T800-22-0x10 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-22-0x11

A Receiver only rack with alarm outputs, AC power supply and dual battery back-up
connections.

Operational Characteristics

Receive only - up to 4 receivers

•

Speaker / Programming panel - with Receiver Speaker Select Switch

•

Alarm Panel

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

•

Configuration Options

Channel Panel

•

Fans - single or double

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

17.75kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

Alarm Panel

Power

PSU Fail

Batt Fail

Forward

Reflected

Alarm#1

Alarm#2

Alarm#3

Alarm#4

Forward

Test

Power
Supply

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Supply

Off
On

Receiver

T800//

Gate

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Supply

Off
On

Gate

Speaker Panel

T800//T800//

25

16

Receiver

Speaker Select

OPTIONAL

CHANNEL

PANEL

34

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Supply

On

Receiver

T800//

Gating

Gate

Off

Gate

Sensitivity

Supply

Line
level

Monitor
Volume

Off

On

Monitor

Mute

OPTIONAL

BLANK

Power Supply

T800//

Overload

Standby

On

OPTIONAL

BLANK

Power

REAR VIEW

Speaker

Panel

ReceiverReceiverReceiverReceiver

Alarm

T800-50-0002 T800-50-0002

1

Output

13.8V
25A
Max.

2
3

+

4

-

5

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

QTY

1T800-11-0004 RACK, FRAME ONLY, ASSEMBLED 2 BATT BACK-UP
2T800-41-0002 DOUBLE GUIDE KIT
1T800-43-0000 GUIDE KIT T1500/300 DOUBLE 'D'
1T800-44-0000 T800 PS GUIDE KIT
1T800-15-0002 SPEAKER / PROGRAM PANEL WITH 6-WAY SWITCH
1T800-40-0000 FIXING KIT ONLY
2T800-50-0002 BACKPLANE
1X800-93-0001 POWER RAIL (STANDARD)

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 4
SECTION 8
SECTION 4
SECTION 5
SECTION 3

T A I T

Radio Communications
Christchurch
New Zealand

drg No changed and Ref added
Original

45Frame label removed

Version

AMM 6/4/00ABB7 Cabling note added
AMM 1/2/00ABB6 Modules rearranged
AMM 25/8/99ABB
AMM 20/10/98ABB1

AMM 22/7/99ABB

Drawn DateChecked

AMM 8/3/99ABB3 Parts list added

TITLE:

DRAWING:

RACK, RX ONLY (4RX + AL

T800-22-0x11

T800 Series II Conventional Equipment Section 2

T800-22-0x12

Receive only rack similar to T800-22-0x11; but with no alarm outputs.

Operational Characteristics

Receive only - up to 4 receivers

•

Speaker / Programming panel - with Receiver Speaker Select Switch

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

•

Configuration Options

Channel Panel

•

Fans - single or double

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

16.35kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

T800//

Excellence in Radio
Communications

Power
Supply

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor

Volume

Monitor

Mute

Receiver

T800//

Gate

Supply

Off
On

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Supply

Off
On

Speaker Panel

34

T800//

25

Gate

16

Receiver

Speaker Select

OPTIONAL
CHANNEL

PANEL

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Supply

Gate

Off
On

Receiver

T800//

Gating

Sensitivity

Line

level

Monitor
Volume

Monitor

Mute

OPTIONAL

BLANK

Supply

Gate

Off
On

Power Supply

T800//

Overload

Standby

On

OPTIONAL

BLANK

Power

REAR VIEW

Speaker

Panel

ReceiverReceiverReceiverReceiver

T800-50-0002 T800-50-0002

1

Output

13.8V
25A
Max.

2
3

+

4

-

5

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

QTY

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED
2T800-41-0002 DOUBLE GUIDE KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-40-0001 BLANKING BRACKET / FRONT PANEL
1T800-15-0002 SPEAKER / PROGRAM PANEL WITH 6-WAY SWITCH
1T800-40-0000 FIXING KIT ONLY
2T800-50-0002 BACKPLANE
1X800-90-0001 POWER RAIL (STANDARD)

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 8
SECTION 8
SECTION 4
SECTION 5
SECTION 3

T A I T

Radio Communications
Christchurch
New Zealand

5

Spk cabling note added

4

drg No changed and Ref added

3

Parts list added

2

Change of Title

1

Original

Version

AMM 6/4/00ABB
AMM 25/8/99ABB
AMM 8/3/99ABB
AMM 14/12/98ABB
AMM 20/10/98ABB

Drawn DateChecked

TITLE:

DRAWING:

RACK, RX ONLY (4RX

T800-22-0x12

T800 Series II Conventional Equipment Section 2

T800-22-0x13

This rackframe has been superseded by T800-22-0x16.

Copyright TEL 3/7/00

T800 Series II Conventional Equipment Section 2

T800-22-0x14

A dual 25 Watt channel rack, with AC power supply and DC battery back-up
connections.

Operational Characteristics

Dual channel

•

25W output

•

Dual Speaker / Programming panel (switchable)

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

•

Configuration Options

Channel Panel

•

Individual Speaker / Programming panels

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

•

installation kit

microphone

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

16.05kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

Excellence in Radio
Communications

T800//

OPTIONAL SPEAKER

(T800-15-0000)

OPTIONAL DUPLEXER

AND/OR CHANNEL PANEL

Power
Supply

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Supply

Power Supply

T800//

Overload

On

Standby

On

Power

Transmitter

T800//

Gate

Supply

Off
On

Carrier

Line

Sensitivity

Microphone

Speaker Panel

T800//

O
F
F

RX 2

RX 1

On

Supply

AND/OR CHANNEL PANEL

O
F
F

OPTIONAL SPEAKER

(T800-15-0000)

OPTIONAL DUPLEXER

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Supply

Off
On

Transmitter

T800//

Gate

Carrier

Line

Sensitivity

Microphone

REAR VIEW

ReceiverTransmitter

Speaker

Panel

ReceiverTransmitter

1
2
3

+

4

-

5

T800-50-0001

DIODE

PACK

FUSE

EARTH

STUD

Output

13.8V
25A
Max.

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

FUSE

T800-50-0001

BATTERY
BACK-UP

QTY

TB1

REFERENCE

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED, BATTERY BACK-UP
2T800-41-0002 DOUBLE GUIDE KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-15-0003 SPEAKER / PROGRAM PANEL
1T800-40-0001 BLANKING BRACKET / FRONT PANEL SECTION 8
1T800-40-0000 FIXING KIT ONLY
2T800-50-0001 BACKPLANE
1X800-93-0001 POWER RAIL (STANDARD)

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

SECTION 4
SECTION 4
SECTION 4
SECTION 8

SECTION 4
SECTION 5
SECTION 3

T A I T

Radio Communications
Christchurch
New Zealand

5

Drg name changed

4

Dual spk replaced by switched spk

Drg No changed, ref added, PA, PS moved

3
2

Parts list added, fans removed

1

Original

Version

AMM 29/11/99ABB
AMM 2/9/99ABB
AMM 25/8/99ABB
AMM 18/3/99ABB
AMM 12/1/99ABB

Drawn DateChecked

TITLE:

RACK, DUAL 2x25W, SPK SW

DRAWING:

T800-22-0x14 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-22-0x15

A dual 25 Watt channel rack with 2 separate power supplies, one for each channel.
The speaker panel can be switched between receivers.

Operational Characteristics

Dual channel

•

25W output

•

Speaker / Programming panel, with Receiver Selectable Switch

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC Not available

•

x = 3 AC and Battery

•

x = 4 External DC and Battery Not available

•

x = 5 AC and External DC and Battery Not available

•

Configuration Options

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

•

installation kit

microphone

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

16.6kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

T800//

Power Supply

Overload

Standby

On

Power

Power
Supply

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor

Volume

Monitor

Mute

Supply

Off
On

Transmitter

T800//

Gate

Carrier

Line

Sensitivity

Microphone

Supply

Speaker Panel

T800//

O
F
F

RX 1 RX 2

On

O
F
F

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Supply

Off
On

Gate

T800//

Transmitter

Carrier

Line

Sensitivity

Microphone

Supply

Power Supply

T800//

Overload

On

Standby

On

Power

REAR VIEW

ReceiverTransmitter

Speaker

Panel

ReceiverTransmitter

Power
Supply

1
2
3

+

4

-

5

T800-50-0001

DIODE

PACK

FUSE

EARTH

STUD

Output

13.8V
25A
Max.

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

FUSE

T800-50-0001

Output

13.8V
25A
Max.

QTY

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED
2T800-41-0002 DOUBLE GUIDE KIT
2T800-44-0000 T800 PS GUIDE KIT
1T800-15-0003 SPEAKER/PROGRAM PANEL WITH 3 POSITION SWITCH
1T800-40-0000 FIXING KIT ONLY
2T800-50-0001 BACKPLANE
1X800-22-0015 POWER RAIL (STANDARD)

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

+

-

TB1

1
2
3
4
5

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 8
SECTION 4
SECTION 5
SECTION 3

T A I T

Radio Communications
Christchurch
New Zealand

3

Drg name changed

Drg No changed, Ref added, Relay removed

3
2

Standard supply table added

1

Original

Version

AMM 29/11/99ABB
AMM 25/8/99ABB
AMM 3/2/99ABB
AMM 12/1/99ABB

Drawn DateChecked

TITLE:

RACK, DUAL 2x25 WATT, (2 P/SUP

DRAWING:

T800-22-0x15 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-22-0x16

A dual 50 Watt channel rackframe.

Operational Characteristics

Dual channel

•

50W output per channel

•

Speaker / Programming panel, with Receiver Selectable Switch

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

•

Configuration Options

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

•

installation kit

microphone

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

20.7kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

Power Amplifier Receiver

Supply

Low forward power

High reverse power

Power

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Gate

Supply

Off
On

Exciter

T800//T800//

Carrier

Line

Sensitivity

Microphone

Supply

T800//

RX 1 RX 2

On

T800//

O
F
F

O
F
F

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

REAR VIEW

ReceiverPA Exciter

Speaker

Panel

Exciter Receiver

T800// T800//

Gate

Supply

Off

On

Exciter

Carrier

Line

Sensitivity

Microphone

Supply

Power AmplifierSpeaker Panel

On

Supply

Low forward power

High reverse power

Power

FAN (OPTIONAL)FAN (OPTIONAL)

PA

EARTH

STUD

FAN

(OPTIONAL)

DC INPUT FUSE

T800-50-0001

FUSE

T800-50-0001

FAN (OPTIONAL)

TB1

The rack configuration has been changed to reduce

the risk of overheating in some environments.

The optional fans should be fitted.

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

QTY

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED
2T800-41-0002 DOUBLE GUIDE KIT
2T800-45-0000 GUIDE PA 50W KIT
1T800-15-0003 SPEAKER/PROGRAM PANEL WITH 3 POSITION SWITCH
1T800-40-0000 FIXING KIT ONLY
2T800-50-0001 BACKPLANE
1X800-91-0002 POWER RAIL (STANDARD)

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 8
SECTION 4
SECTION 5
SECTION 3

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

T A I T

Radio Communications
Christchurch
New Zealand

3

Drg name changed

Drg No changed, Ref added, PA moved

2
1

Original

Version

AMM 29/11/99ABB
AMM 25/8/99ABB
AMM 15/2/99ABB

Drawn DateChecked

TITLE:

RACK, DUAL 2x50W, (SPK SWITCHED)

DRAWING:

T800-22-0x16 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-22-0x17

This rackframe has been superseded by T800-22-0x14.

Copyright TEL 3/7/00

T800 Series II Conventional Equipment Section 2

T800-22-0x18

A dual channel rackframe suitable for Link and Repeater requirements:
one 50W and one 25W channel.

Operational Characteristics

Dual channel

•

50W / 25W output

•

Speaker / Programming panel, with Receiver Selectable Switch

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

•

Configuration Options

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

•

installation kit

microphone

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

19.8kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Power
Supply

T800// T800//

Gate

Supply

Off
On

Exciter

Carrier

Line

Sensitivity

Microphone

Supply

Power Amplifier

On

Supply

Low forward power

High reverse power

Power

Speaker Panel

T800//

RX 1 RX 2

FAN (OPTIONAL)

Receiver

T800//

O
F
F

O
F
F

Gating

Sensitivity

Line
level

Monitor

Volume

Monitor

Mute

Supply

Off
On

Gate

T800//

Transmitter

Carrier

Line

Sensitivity

Microphone

Supply

Power Supply

T800//

Overload

On

Standby

On

Power

REAR VIEW

ReceiverExciter

Speaker

Panel

PA ReceiverExciter

T800-50-0001

1

Output

13.8V
25A
Max.

2
3

+

4

-

5

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

FAN (OPTIONAL)

T800-50-0001

QTY

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED
2T800-41-0002 DOUBLE GUIDE KIT
1T800-45-0000 GUIDE PA 50W KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-15-0003 SPEAKER / PROGRAM PANEL SWITCHED
2T800-50-0001 BACKPLANE
1X800-90-0003 POWER RAIL (STANDARD)

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 4
SECTION 8
SECTION 5
SECTION 3

T A I T

Radio Communications
Christchurch
New Zealand

1 Original

Version

AMM 3/2/00ABB

Drawn DateChecked

TITLE:

DRAWING:

RACK, DUAL 25/50W

T800-22-0x18 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-22-0x20

A single repeater or base station channel rack up to 100 Watt maximum output. The
rack can accommodate an Rx/Tx Monitor panel and AC power input.

Operational Characteristics

Single channel

•

Up to 100W with option of Transmitter or Exciter / PA combination

•

Speaker / Programming panel

•

Rx/Tx Monitor Panel

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only

•

x = 1 External DC only Not Available

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery Not Available

•

x = 5 AC and External DC and Battery

•

Configuration Options

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

•

installation kit

microphone

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

25W - 12.2kg
50W - 15.95kg
100W - 16.3kg

NOTE: This product offers the versatility of fitt ing personality boards to provide customised
solutions for specific req uir em ent s.
Refer to RSD for design and build of personality boards.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

EARTH

STUD

T800//

Volume

Off

Rx/Tx Monitor

Power
Supply

Output

13.8V
25A
Max.

Supply

Volts
Rx Signal
Rx Line
Tx Line
Fwd Pwr
Rev Pwr

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor

Volume

Monitor

Mute

T800// T800//

Gate

Supply

Off
On

TRANSMITTER

Exciter

Carrier

Line

Sensitivity

Microphone

OPTIONAL

Supply

Power Amplifier

On

Supply

Low forward power

High reverse power

Power

FAN (OPTIONAL)

OPTIONAL

BLANK
PANEL

Excellence in Radio
Communications

T800//

OPTIONAL

DUPLEXER

Speaker Panel

T800//

OPTIONAL
CHANNEL

PANEL

T800//

Power Supply

Overload

Standby

On

Power

REAR VIEW

Speaker

Panel

PA ReceiverExciter

T800-50-0000

T800-60-0000

1
2
3

+

4

-

5

FAN (OPTIONAL)

FUSE

Rx/Tx MON

T818-01-0000

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

TB1

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

T A I T

Radio Communications
Christchurch
New Zealand

4

Drg name changed

3

Drg No changed, Ref added

2

Parts list added

1

Original

Version

AMM 29/11/99ABB
AMM 25/8/99ABB
AMM 8/3/99ABB
AMM 12/1/99ABB

Drawn DateChecked

REFERENCE

QTY

SECTION 4

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED

SECTION 4

1T800-41-0002 DOUBLE GUIDE KIT

SECTION 4

1T800-43-0001 GUIDE KIT T1500/300 SINGLE 'D'

SECTION 4

1T800-45-0000 GUIDE PA 50W KIT
1T800-44-0000 T800 PS GUIDE KIT

SECTION 4
SECTION 8

1T800-15-0000 SPEAKER / PROGRAM PANEL

SECTION 4

1T800-40-0000 FIXING KIT ONLY

SECTION 8

1T800-40-0001 BLANKING BRACKET / FRONT PANEL
1T800-50-0000 BACKPLANE

SECTION 5

1T800-60-0000 PERSONALITY BOARD

SECTION 6

1X800-90-0000 POWER RAIL (STANDARD)

SECTION 3

TITLE:

RACK, SNGL<100W, (MONITOR)

DRAWING:

T800-22-0x20 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-22-0x21

A single 25 Watt repeater or base station channel rack to accommodate an Rx/Tx
Monitor and rack mounted circuit breaker for protection on the DC power input.

Operational Characteristics

Single channel

•

25W output only

•

Speaker / Programming panel

•

Panel circuit breaker

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only Not Available

•

x = 1 External DC only

•

x = 2 AC and External DC Not Available

•

x = 3 AC and Battery Not Available

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery Not Available

•

Configuration Options

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

•

(see T800-22-0x20)

(see T800-22-0x20)
(see T800-22-0x20)

(see T800-22-0x20)

installation kit

microphone

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

10.35kg

NOTE:

This product offers the versatility of fitting personality boards to provide
customised solutions for specific requirements.
Refer to RSD for design and build of personality boards.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

T800//

Volume

Off

Rx/Tx Monitor

Circuit

Breaker

Supply

Volts
Rx Signal
Rx Line
Tx Line
Fwd Pwr
Rev Pwr

T800//

Receiver

Gating

Gate

Sensitivity

Supply

Line
level

Monitor

Volume

Off
On

Monitor

Mute

Speaker

Panel

Supply

Excellence in Radio
Communications

T800//

On

Transmitter

T800// T800//

Carrier

Line

Sensitivity

Microphone

Excellence in Radio
Communications

T800//

OPTIONAL

DUPLEXER

Speaker Panel

T800//

OPTIONAL
CHANNEL

PANEL

REAR VIEW

ReceiverTransmitter

Circuit Breaker

On

1

0

Off

Rx/Tx MON

Supply

12V

EARTH

STUD

DC INPUT

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

T800-50-0000

T800-60-0000

T818-01-0000

QTY

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED
1T800-41-0002 DOUBLE GUIDE KIT
1T800-43-0001 GUIDE KIT T1500/300 SINGLE 'D'
1T800-45-0000 GUIDE PA 50W KIT
1T800-15-0000 SPEAKER / PROGRAM PANEL
1T800-40-0000 FIXING KIT ONLY
1T800-40-0001 BLANKING BRACKET / FRONT PANEL
1T800-17-0010 PANEL CIRCUIT BREAKER WITH 10AMP SWITCH
1T800-50-0000 BACKPLANE
1T800-60-0000 PERSONALITY BOARD
1316-06615-00 BLANKING FRONT PANEL ONLY
1X800-22-0121 POWER RAIL (STANDARD)

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

TB1

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 4
SECTION 8
SECTION 4
SECTION 8
SECTION 8
SECTION 5
SECTION 6
SECTION 8
SECTION 3

T A I T

Radio Communications
Christchurch
New Zealand

5

Drg name changed

4

Drg No changed, Ref added

3

Parts list added

2

Change of Title

1

Original

Version

AMM 29/11/99ABB
AMM 25/8/99ABB
AMM 18/3/99ABB
AMM 14/12/98ABB
AMM 22/10/98ABB

Drawn DateChecked

TITLE:

RACK, SNGL<25W, (MONITOR)

DRAWING:

T800-22-0x21 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-22-0x22

A single 50 Watt repeater or base station channel rack to accommodate an Rx/Tx
Monitor and rack mounted circuit breaker for protection on the DC power input.

Operational Characteristics

Single channel

•

50W output only

•

Speaker / Programming panel

•

Panel circuit breaker

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only Not Available

•

x = 1 External DC only

•

x = 2 AC and External DC Not Available

•

x = 3 AC and Battery Not Available

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery Not Available

•

Configuration Options

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

•

(see T800-22-0x20)

(see T800-22-0x20)
(see T800-22-0x20)

(see T800-22-0x20)

installation kit

microphone

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

14.1kg

NOTE:

This product offers the versatility of fitting personality boards to provide
customised solutions for specific requirements.
Refer to RSD for design and build of personality boards.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

EARTH

STUD

T800//

Volume

Off

Rx/Tx Monitor

Circuit

Breaker

DC INPUT

Supply

Volts
Rx Signal
Rx Line
Tx Line
Fwd Pwr
Rev Pwr

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor

Volume

Monitor

Mute

Speaker

Panel

T800// T800//

Gate

Supply

Off
On

Exciter

Carrier

Line

Sensitivity

Microphone

Supply

Power Amplifier

On

Supply

Low forward power

High reverse power

Power

FAN (OPTIONAL)

REAR VIEW

PA ReceiverExciter

FAN (OPTIONAL)

Excellence in Radio
Communications

T800// T800//

OPTIONAL

DUPLEXER

Speaker Panel

T800//

OPTIONAL
CHANNEL

PANEL

Rx/Tx MON

T800-50-0000

T818-01-0000

T800-60-0000

Circuit Breaker

Supply

12V

On

1

0

Off

TB1

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

T800-17-0020 PANEL CIRCUIT BREAKER WITH 20AMP SWITCH

T A I T

Radio Communications
Christchurch
New Zealand

5

Drg name changed

4

Drg No changed, Ref added

3

Parts list added

2

Change of Title

1

Original

Version

AMM 29/11/99ABB
AMM 25/8/99ABB
AMM 8/3/99ABB
AMM 14/12/98ABB
AMM 22/10/98ABB

Drawn DateChecked

REFERENCE

QTY

SECTION 4

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED

SECTION 4

1T800-41-0002 DOUBLE GUIDE KIT

SECTION 4

1T800-43-0001 GUIDE KIT T1500/300 SINGLE 'D'

SECTION 4

1T800-45-0000 GUIDE PA 50W KIT

SECTION 8

1T800-15-0000 SPEAKER / PROGRAM PANEL

SECTION 4

1T800-40-0000 FIXING KIT ONLY

SECTION 8

1T800-40-0001 BLANKING BRACKET / FRONT PANEL
1

SECTION 8
SECTION 5

1T800-50-0000 BACKPLANE

SECTION 6

1T800-60-0000 PERSONALITY BOARD

SECTION 3

1X800-22-0122 POWER RAIL (STANDARD)

TITLE:

RACK, SNGL<=50W, (MONITOR)

DRAWING:

T800-22-0x22 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-22-0x23

A single channel rack with 50 Watt maximum output, alarm outputs and AC power
supply.

Operational Characteristics

Single channel

•

Up to 50W output

•

Speaker / Programming panel

•

Alarm Panel

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

•

Configuration Options

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

•

installation kit

microphone

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

25W - 12.1kg
50W - 15.85kg

NOTE:

This product offers the versatility of fitting personality boards to provide
customised solutions for specific requirements.
Refer to RSD for design and build of personality boards.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

T800//

Alarm Panel

Power

PSU Fail

Batt Fail

Forward

Reflected

Alarm#1

Alarm#2

Alarm#3

Alarm#4

Forward

Test

Power

Supply

T800//

Receiver

Gating

Gate

Sensitivity

Supply

Line
level

Monitor
Volume

Off
On

Monitor

Mute

TRANSMITTER

Speaker

Panel

Exciter

T800// T800//

Carrier

Supply

Line

Sensitivity

Microphone

Power Amplifier

On

Supply

Low forward power

High reverse power

Power

FAN (OPTIONAL)

OPTIONAL

OPTIONAL

BLANK

REAR VIEW

PA

Excellence in Radio
Communications

T800//

OPTIONAL

DUPLEXER

Transmitter

or Exciter

Speaker Panel

T800// T800//

OPTIONAL

CH/PNL

Receiver

Power Supply

Overload

Standby

On

Power

OPTIONAL

BLANK

Alarm

1
2
3

+

4

-

5

FAN

(OPTIONAL)

DIODE

PACK

EARTH

STUD

Output

13.8V
25A
Max.

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

T800-50-0000

T800-60-0002

FUSE

Personality

Board

BATTERY
BACK-UP

QTY

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED
1T800-41-0002 DOUBLE GUIDE KIT
1T800-45-0000 GUIDE PA 50W KIT
1T800-43-0000 GUIDE KIT T1500/300
1T800-44-0000 T800 PS GUIDE KIT
1T800-15-0000 SPEAKER/PROGRAM PANEL
1T800-40-0000 FIXING KIT ONLY
1T800-40-0001 BLANKING BRACKET / F-PNL KIT
1T800-50-0000 BACKPLANE
1T800-60-0002 PERSONALITY BOARD + CH/PNL + ALARMS (0V)
1X800-93-0000 POWER RAIL (STANDARD)

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

TB1

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 4
SECTION 4
SECTION 8
SECTION 4
SECTION 8
SECTION 5
SECTION 6
SECTION 3

T A I T

Radio Communications
Christchurch
New Zealand

4

Drg name changed

3

Drg No changed, Ref added

2

Change personality board

1

Original

Version

AMM 29/11/99ABB
AMM 25/8/99ABB
AMM 30/3/99ABB
AMM 15/2/99ABB

Drawn DateChecked

TITLE:

RACK, SNGL<100W, (ALARMS 0V)

DRAWING:

T800-22-0x23 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-22-0x24

A single channel rack with 50 Watt maximum output, alarm outputs (LO) and AC
power supply.

Operational Characteristics

Single channel

•

Up to 50W output

•

Speaker / Programming panel

•

Alarm Panel

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

•

Configuration Options

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

•

installation kit

microphone

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

25W - 12.1kg
50W - 15.85kg

NOTE: This product offers the versatility of fitt ing personality boards to provide customised
solutions for specific req uir em ent s.
Refer to RSD for design and build of personality boards.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

T800//

Alarm Panel

Power

PSU Fail

Batt Fail

Forward

Reflected

Alarm#1

Alarm#2

Alarm#3

Alarm#4

Forward

Test

Power

Supply

T800//

Receiver

Gating

Gate

Sensitivity

Supply

Line
level

Monitor
Volume

Off
On

Monitor

Mute

TRANSMITTER

Speaker

Panel

Exciter

T800// T800//

Carrier

Supply

Line

Sensitivity

Microphone

OPTIONAL

On

OPTIONAL

Power Amplifier

Supply

Low forward power

High reverse power

Power

BLANK

REAR VIEW

T800//

FAN (OPTIONAL)

OPTIONAL

DUPLEXER

PA

Transmitter

or Exciter

Excellence in Radio
Communications

Speaker Panel

T800// T800//

OPTIONAL

CH/PNL

Receiver

Power Supply

Overload

Standby

On

Power

OPTIONAL

BLANK

Alarm

1
2
3

+

4

-

5

FAN

(OPTIONAL)

DIODE
PACK

EARTH

STUD

Output

13.8V
25A
Max.

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

T800-50-0000

T800-60-0001

FUSE

Personality

Board

BATTERY
BACK-UP

QTY

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED
1T800-41-0002 DOUBLE GUIDE KIT
1T800-45-0000 GUIDE PA 50W KIT
1T800-43-0000 GUIDE KIT T1500/300
1T800-44-0000 T800 PS GUIDE KIT
1T800-15-0000 SPEAKER/PROGRAM PANEL
1T800-40-0000 FIXING KIT ONLY
1T800-40-0001 BLANKING BRACKET / F-PNL KIT
1T800-50-0000 BACKPLANE
1T800-60-0001 PERSONALITY BOARD + CH/PNL + ALARMS (LO)
1X800-93-0000 POWER RAIL (STANDARD)

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

TB1

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 4
SECTION 4
SECTION 8
SECTION 4
SECTION 8
SECTION 5
SECTION 6
SECTION 3

T A I T

Radio Communications
Christchurch
New Zealand

12Original

Version

Drg name changed

AMM 29/11/99ABB
AMM 7/9/99ABB

Drawn DateChecked

TITLE:

RACK, SNGL<100W, (ALARMS LO)

DRAWING:

T800-22-0x24 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-23-0000

A single channel rack with 25 Watt maximum output mounted in a 2RU Slimline
configuration for use in DC situations.

Operational Characteristics

Single channel

•

Up to 25W output

•

Speaker / Programming Port

•

Power Supply Options

External DC only

•

Configuration Options

Coaxial Relay

•

Microphone

•

Mechanical Characteristics

2 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 89mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

25W – 3.9kg

This configuration includes Receiver and Transmitter modules.
(to be specified when ordering)

Copyright TEL 3/7/00

FRONT VIEW

T800//

Receiver

Supply

Gate

Gating

Sensitivity

Line
Level

Monitor
Volume

On Off

REAR VIEW

Monitor

ReceiverTransmitter

Transmitter

SupplyOn

Line

MicrophoneCarrier

Sensitivity

T800II Slimline

TB

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

T A I T

Radio Communications
Christchurch
New Zealand

1 Original

Version

AMM 20/9/99ABB

Drawn DateChecked

TITLE:

DRAWING:

QTY

REFERENCE

1T800-23-0000 SLIMLINE ASSEMBLY KIT + CABLES

SECTION 4

1T8n5-nn-nnnn RECEIVER

SECTION 8

1T8n6-nn-nnnn TRANSMITTER

SECTION 8

SLIMLINE 25W DC

T800-23-0000

T800 Series II Conventional Equipment Section 2

T800-23-0001

A single channel rack with 25 Watt maximum output mounted in a 2RU Slimline
configuration, with an AC power supply.

Operational Characteristics

Single channel

•

Up to 25W output

•

Speaker / Programming Port

•

Power Supply Options

AC only

•

Configuration Options

Coaxial Relay

•

Microphone

•

Mechanical Characteristics

2 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 89mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

25W – 8.55kg

This configuration includes Receiver and Transmitter modules.
(to be specified when ordering)

.

Copyright TEL 3/7/00

FRONT VIEW

y

T800//

Receiver

Supply

Gate

Gating

Sensitivity

Line
Level

Monitor
Volume

On Off

REAR VIEW

Monitor

ReceiverTransmitter

Transmitter

SupplyOn

Line

MicrophoneCarrier

Sensitivity

T800II Slimline

Power Suppl

TB

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

T A I T

Radio Communications
Christchurch
New Zealand

1 Original

Version

AMM 20/9/99ABB

Drawn DateChecked

TITLE:

DRAWING:

QTY

REFERENCE

1T800-23-0001 SLIMLINE ASSEMBLY KIT + CABLES + POWER SUPPLY

SECTION 4

1T8n5-nn-nnnn RECEIVER

SECTION 8

1T8n6-nn-nnnn TRANSMITTER

SECTION 8

SLIMLINE 25W AC

T800-23-0001

T800 Series II Conventional Equipment Section 2

T800-23-1001

A single channel rack, transmitter only, with 25 Watt maximum output mounted in a
2RU Slimline configuration, with an AC power supply.
Suitable for use in Paging situations

Operational Characteristics

Single channel

•

Up to 25W output

•

Speaker / Programming Port

•

Power Supply Options

AC only

•

Configuration Options

Coaxial Relay

•

Microphone

•

Mechanical Characteristics

2 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 89mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

25W – 6.35kg

This configuration includes Transmitter module.
(to be specified when ordering)

.

Copyright TEL 3/7/00

FRONT VIEW

y

T800//

Paging Module

Programming

Port

Transmitter

REAR VIEW

Transmitter

SupplyOn

Line

MicrophoneCarrier

Sensitivity

T800II Slimline

Power Suppl

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

T A I T

Radio Communications
Christchurch
New Zealand

1 Original

Version

AMM 6/3/00ABB

Drawn DateChecked

TITLE:

DRAWING:

QTY

REFERENCE

1T800-23-1001 SLIMLINE ASSEMBLY KIT + CABLES + POWER SUPPLY

SECTION 4

1T8N6-nn-1000 TRANSMITTER

SECTION 8

SLIMLINE PAGING

T800-23-1001

T800 Series II Conventional Equipment Section 2

T800-24-0x00

A single channel Quasi Sync channel with up to 100 Watt output, AC power supply
and alarm outputs.

Operational Characteristics

Quasi Sync working

•

Single channel

•

Up to 100W output

•

Reference Input

•

Speaker / Programming panel

•

Alarm Panel

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x =

0 AC only
1 External DC only
2 AC and External DC
3 AC and Battery
4 External DC and Battery
5 AC and External DC and Battery

Configuration Options

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0012

•

installation kit

microphone

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

25W - 12.1kg
50W - 15.85kg

Rack “Items Supplied as Standard” does not include modules other than those

100W - 16.2kg

listed on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

T800//

Alarm Panel

Power

PSU Fail

Batt Fail

Forward

Reflected

Alarm#1

Alarm#2

Alarm#3

Alarm#4

Forward

Test

Power

Supply

T800//

Receiver

Gating

Gate

Sensitivity

Supply

Line
level

Monitor
Volume

Off
On

Monitor

Mute

Speaker

Panel

Exciter

T800// T800//

Carrier

Line

Supply

Sensitivity

Microphone

OPTIONAL

TRANSMITTER

On

Power Amplifier

OPTIONAL

BLANK

REAR VIEW

Excellence in Radio
Communications

Supply

Low forward power

High reverse power

Power

T800// T800//

(KANNEL 561)

Z2

FAN (OPTIONAL)

OPTIONAL

DUPLEXER

PA ReceiverExciter

Speaker Panel

T800//

OPTIONAL

CHANNEL

PANEL

Power Supply

Overload

Standby

On

Power

OPTIONAL

BLANK

Alarm

1
2
3

+

4

-

5

FAN (OPTIONAL)

T800-24-0000

DIODE

PACK

EARTH

STUD

Output

13.8V
25A
Max.

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

T800-52-0000

FUSE

REFERENCE

INPUT

BATTERY
BACK-UP

QTY

TB1

REFERENCE

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED, BATTERY BACK-UP
1T800-41-0002 DOUBLE GUIDE KIT
1T800-43-0000 GUIDE KIT T1500/300 DOUBLE 'D'
1T800-45-0000 GUIDE PA 50W KIT
1T800-44-0000 T800 PS GUIDE KIT SECTION 4
1T800-15-0000 SPEAKER / PROGRAM PANEL
1T800-40-0000 FIXING KIT ONLY
1T800-40-0001 BLANKING BRACKET / FRONT PANEL
1T800-52-0000 BACKPLANE
1X800-93-0000 POWER RAIL
1219-02601-00 REFERENCE LEAD

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

SECTION 4
SECTION 4
SECTION 4
SECTION 4

SECTION 8
SECTION 4
SECTION 8
SECTION 5
SECTION 3

T A I T

Radio Communications
Christchurch
New Zealand

5

Drg name changed

4

Drg No changed, Ref added

3

Parts list added

2

Change of Title

1

Original

Version

AMM 30/11/99ABB
AMM 25/8/99ABB
AMM 18/3/99ABB
AMM 14/12/98ABB
AMM 22/10/98ABB

Drawn DateChecked

TITLE:

RACK, QS TX<100W, (ALARM)

DRAWING:

T800-24-0x00 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-24-0x01

Dual channel Quasi Sync rack with 50 Watt maximum output, and AC power supply.

Operational Characteristics

Quasi Sync working

•

Dual channel

•

50W output maximum

•

Reference Input

•

Speaker / Programming panel

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x =

0 AC only
1 External DC only
2 AC and External DC
3 AC and Battery
4 External DC and Battery
5 AC and External DC and Battery

Configuration Options

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0012

•

installation kit

microphone

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

23.55kg

Rack “Items Supplied as Standard” does not include modules other than those
listed on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

EARTH STUD

EARTH

STUD

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

T800// T800//

Gate

Supply

Off
On

Exciter

Carrier

Line

Sensitivity

Microphone

On

Supply

Supply

On

Power Supply

T800//

Overload

Standby

On

OPTIONAL

BLANK

Power

Power Amplifier

Supply

Low forward power

High reverse power

Power

FAN (OPTIONAL) FAN (OPTIONAL)

T800//

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Gate

Supply

Off
On

Exciter

T800//T800//

Carrier

Line

Sensitivity

Microphone

REAR VIEW

FUSE 2

Power
Supply

Output

13.8V
25A
Max.

T800-52-0000

1
2
3

+

4

-

5

FUSE 1

REFERENCE

ReceiverExciter

INPUT

FAN (OPTIONAL)

BATTERY
BACK-UP

PA ReceiverExciter

T800-52-0000

FAN (OPTIONAL)

REFERENCE

INPUT

DIODE

PACK

Power AmplifierReceiver

Supply

Low forward power

High reverse power

Power

PA

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

TB1

It is recommended that the optional fans are fitted

to reduce the risk of overheating in some

environments.

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

5

T A I T

Radio Communications
Christchurch
New Zealand

Drg name changed

Drg No changed, Ref added

4
3

Parts list added

2

Change of Title

1

Original

Version

AMM 29/11/99ABB
AMM 25/8/99ABB
AMM 18/3/99ABB
AMM 14/12/98ABB
AMM 21/10/98ABB

Drawn DateChecked

REFERENCE

QTY

SECTION 4

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED

SECTION 4

2T800-41-0002 DOUBLE GUIDE KIT

SECTION 4

2T800-45-0000 GUIDE PA 50W KIT

SECTION 4

1T800-44-0000 T800 PS GUIDE KIT

SECTION 5

2T800-52-0000 BACKPLANE
1X800-93-0002 POWER RAIL (STANDARD)

SECTION 3

2219-02601-00 REFERENCE LEAD

TITLE:

RACK, QS TX 2x50W, ( NO ALARM)

DRAWING:

T800-24-0x01 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-24-0x02

A single channel Quasi Sync rack with output up to 100 Watt, AC and battery power
supply.

Operational Characteristics

Quasi Sync working

•

Single channel

•

Up to 100W output

•

Reference Input

•

Speaker / Programming panel

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x =

0 AC only
1 External DC only
2 AC and External DC
3 AC and Battery
4 External DC and Battery
5 AC and External DC and Battery

Configuration Options

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0012

•

installation kit

microphone

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

25W - 10.7kg
50W - 13.9kg

Rack “Items Supplied as Standard” does not include modules other than those

100W - 14.25kg

listed on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

T800//

Rec eiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Power
Supply

T800// T800//

Gate

Supply

Off
On

Exciter

Carrier

Line

Sensitivity

Microphone

QS LINK

Power Amplifier

On

Supply

Supply

Low forward power

High reverse power

Power

T800//

FAN (OPTIONAL)

DUPLEXER

Speaker Panel

O
F
F

RX 1 RX 2

O
F
F

OPTIONAL

or

CHANNEL

PANEL

T800//

Rec eiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

T800//

Gate

Supply

Off
On

REAR VIEW

ReceiverTransmitter

Speaker

Panel

PA ReceiverExciter

Transmitter

Carrier

Line

Sensitivity

Microphone

Power Supply

T800//

Overload

On

Supply

Standby

On

Power

OPTIONAL

BLANK

1
2
3

+

4

-

5

T800-50-0001

EARTH

STUD

Output

13.8V
25A
Max.

FUSE 2 FUSE 1

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

FAN (OPTIONAL)

T800-52-0000

REFERENCE

INPUT

TB1

QTY

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED
1T800-41-0002 DOUBLE GUIDE KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-45-0000 GUIDE PA 50W KIT
1T800-15-0003 SPEAKER / PROGRAM PANEL, SWITCHED
1T800-40-0000 FIXING KIT ONLY

1T800-50-0001 BACKPLANE
1X800-90-0003 POWER RAIL (STANDARD) SECTION 3
1219-02601-00 REFERENCE INPUT LEAD

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 4
SECTION 8
SECTION 8
SECTION 51T800-52-0000 BACKPLANE, RACK, QS
SECTION 5

T A I T

Radio Communications
Christchurch
New Zealand

12Original

Version

Drg name changed

AMM 29/11/99ABB
AMM 22/10/99ABB

Drawn DateChecked

TITLE:

RACK, QS TX<50W, LINK TX/RX

DRAWING:

T800-24-0x02 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-24-0x03

A single channel Quasi Sync channel with up to 100 Watt output, and AC power
supply.

Operational Characteristics

Quasi Sync working

•

Single channel

•

Up to 100W output

•

Reference Input

•

Speaker / Programming panel

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x =

0 AC only
1 External DC only
2 AC and External DC
3 AC and Battery
4 External DC and Battery
5 AC and External DC and Battery

Configuration Options

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0012

•

installation kit

microphone

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

25W - 11.25kg
50W - 15.0kg

Rack “Items Supplied as Standard” does not include modules other than those

100W - 15.55kg

listed on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

T800//

Excellence in Radio
Communications

Power

Supply

T800//

Rec eiver

Gating

Gate

Sensitivity

Supply

Line

level

Monitor
Volume

Off
On

Monitor

Mute

Speaker

Panel

Exciter

T800// T800//

Carrier

Line

Supply

Sensitivity

Microphone

OPTIONAL

TRANSMITTER

Power Amplifier

On

OPTIONAL

BLANK

REAR VIEW

Excellence in Radio
Communications

T800// T800//

Supply

Low forward power

High reverse power

Power

Z2

(KANNEL 561)

FAN (OPTIONAL)

OPTIONAL

DUPLEXER

PA ReceiverExciter

Speaker Panel

T800//

OPTIONAL
CHANNEL

PANEL

Power Supply

Overload

Standby

On

Power

OPTIONAL

BLANK

1
2
3

+

4

-

5

FAN (OPTIONAL)

RACK
TYPE AND
SERIAL No

EARTH

STUD

Output

13.8V
25A
Max.

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

T800-52-0000

WARNING

FUSE

REFERENCE

INPUT

REFER TO SECTION 3

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

TB1

REFERENCE

QTY

SECTION 4

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED, BATTERY BACK-UP

SECTION 4

1T800-41-0002 DOUBLE GUIDE KIT

SECTION 4

1T800-45-0000 GUIDE PA 50W KIT
1T800-44-0000 T800 PS GUIDE KIT SECTION 4

SECTION 8

1T800-15-0000 SPEAKER / PROGRAM PANEL

SECTION 4

1T800-40-0000 FIXING KIT ONLY

SECTION 8

2T800-40-0001 BLANKING BRACKET / FRONT PANEL

SECTION 5

1T800-52-0000 BACKPLANE
1X800-90-0000 POWER RAIL (STANDARD)

SECTION 3

OF THE

REFERENCE GUIDE

FOR

T A I T

Radio Communications
Christchurch
New Zealand

1 Origin a l

Version

AMM 29/11/99ABB

Drawn DateChecked

TITLE:

RACK, QS TX <100W, (NO ALARM)

DRAWING:

T800-24-0x03 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-24-0600

Dual channel Quasi Sync monitoring receivers, with AC power and alarm outputs.

Operational Characteristics

Quasi Sync working

•

Single channel

•

Speaker / Programming panel

•

Alarm Panel

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x =

0 AC only
1 External DC only
2 AC and External DC
3 AC and Battery
4 External DC and Battery
5 AC and External DC and Battery

Configuration Options

Coaxial Relay

•

Fans - single or double

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

2 PSU + 2 Rx + Alarm – 15.1kg
2 PSU + 1 Rx + Alarm – 12.35kg
2 PSU + 2 Rx - 13.7kg
2 PSU + 1 Rx - 10.95kg

Rack “Items Supplied as Standard” does not include modules other than those
listed on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

Speaker Panel

T800//

OPTIONAL
CHANNEL

PANEL

Power

Supply

T800//

Rec eiver

Gating

Sensitivity

Line

level

Monitor
Volume

Monitor

Mute

Power
Supply

Gate

Supply

Off
On

Rec eiver

T800//

Gating

Gate

Sensitivity

Supply

Line
level

Monitor
Volume

Off
On

Monitor

Mute

OPTIONAL

BLANK PANEL

Speaker Panel

T800// T800//

OPTIONAL
CHANNEL

PANEL or

BLANK PANEL

REAR VIEW

Alarm

Speaker

Panel

Alarm Panel

T800//

Power

PSU Fail

Batt Fail

Forward

Reflected

Alarm#1

Alarm#2

Alarm#3

Alarm#4

LEFT RX: Z3

(KANNEL 503)

Forward Test

RIGHT RX: Z4

(KANNEL 567)

OPTIONAL

BLANK PANEL

Power Supply

ReceiverReceiver

Overload

Standby

On

Power Supply

T800//

Overload

Standby

On

Speaker

Panel

Power

Power

EARTH STUD

TA136-02

T800-50-0002

Output

13.8V
15A
Max.

1
2

Output

3

13.8V

+

4

15A

-

5

Max.

1
2
3

+

4

-

5

OPTIONAL

T800-24-0600

BATTERY
BACK -UP

TB1 TB2

PART NUMBER DESCRIPTION

BATTERY
BACK -UP

DIODE

ITEMS SUPPLIED AS STANDARD

OPTIONAL

TB3

QTY

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED, BATTERY BACK-UP
1T800-41-0002 DOUBLE GUIDE KIT
1T800-43-0000 GUIDE KIT T1500/300 DOUBLE 'D'
2T800-44-0000 T800 PS GUIDE KIT
1T800-15-0000 SPEAKER / PROGRAM PANEL
1T800-40-0000 FIXING KIT ONLY
1T800-40-0001 BLANKING BRACKET / FRONT PANEL
1T800-50-0002 BACKPLANE
2316-06615-00 BLANKING FRONT PANEL ONLY
1X80 0-24-0600 RACK KIT
1W800-24-0600 WIRING KIT

T A I T

Radio Communications
Christchurch
New Zealand

4
3
2
1

Version

Parts list added
Alarm panel added
Change of Title
Original

AMM 18/3/99
AMM 20/1/99
AMM 14/12/98ABB
AMM 20/10/98ABB

Drawn DateChecked

TITLE:

DRAWING:

RACK, QS TX MON AC

(2RX + 2PSU + ALARM)

T800-24-0600

T800 Series II Conventional Equipment Section 2

T800-24-0601

Dual channel Quasi Sync monitoring receivers, with AC power .

Operational Characteristics

Quasi Sync working

•

Single channel

•

Speaker / Programming panel

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x =

0 AC only
1 External DC only
2 AC and External DC
3 AC and Battery
4 External DC and Battery
5 AC and External DC and Battery

Configuration Options

Coaxial Relay

•

Fans - single or double

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

2 PSU + 2 Rx – 13.7kg
2 PSU + 1 Rx – 10.95kg

Rack “Items Supplied as Standard” does not include modules other than those
listed on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

T800//

Speaker Panel

Power

Supply

T800//

Rec eiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Power

Supply

Excellence in Radio
Communications

T800//

Gate

Supply

Off
On

OPTIONAL
RECEIVER

Excellence in Radio
Communications

T800//

OPTIONAL

SPKR/PROG

PANEL

Excellence in Radio
Communications

T800// T800//

Power Supply

Overload

Standby

On

Power

T800//

Power Supply

Overload

Standby

On

Power

REAR VIEW

Receiver

Speaker

Panel

EARTH

STUD

Output

13.8V
25A
Max.

1
2

Output

3

13.8V

+

4

25A

-

5

Max.

TB2

1
2
3

+

4

-

5

TB3

MAX O/P

20A

DIODE

PACK

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

T800-50-0002

DR1

FUSE 1

REFERENCE

INPUT

TB1

REFERENCE

QTY

SECTION 4

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED

SECTION 4

1T800-41-0002 DOUBLE GUIDE KIT

SECTION 4

2T800-44-0000 T800 PS GUIDE KIT

SECTION 8

1T800-15-0000 SPEAKER / PROGRAM PANEL

SECTION 8

1T800-40-0001 BLANK PANEL AND FIXING KIT

SECTION 82T800-40-0000 FIXING KIT ONLY
SECTION 5

1T800-50-0002 BACKPLANE
1X800-24-0601 STANDARD LOOM ASSEMBLY SECTION 3
1W800-24-0601 WIRING KIT
2316-06615-00 BLANK PANEL

T A I T

Radio Communications
Christchurch
New Zealand

1 Origin a l

Version

AMM 22/10/99ABB

Drawn DateChecked

TITLE:

RACK, QS MON, AC (2RX + 2PSU)

DRAWING:

T800-24-0601

T800 Series II Conventional Equipment Section 2

T800-25-0000

A single 25W channel, housed in a portable case with sealed lead acid batteries.

Operational Characteristics

Single channel

•

Up to 25W output

•

DC only operation - Batteries and external DC supply input

•

Speaker / Programming panel

•

DC line fuse

•

Backplane interface

•

Battery Isolation Switch

•

Configuration Options

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Antenna

•

Mechanical Characteristics

Portable case to house up to 4 modules

•

Top Mounting Duplexer Tray

•

Size

•

Case Only with Handles and Connectors
Height - 242mm 305mm
Width - 255mm 300mm
Depth - 460mm 460mm

Weight – (rackframe with modules shown)

•

15.85kg

CAUTION: If operating above 15 Watts, front and rear covers must be removed.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

Receiver

T800//

Gating

Gate

Sensitivity

Supply

Line
level

Monitor

Volume

Off
On

Monitor

Mute

EXTERNAL DC BATTERY OPERATION

T8n5 -nn-0200 T8n6 -nn-0200

Transmitter

T800// T800//

Carrier

Line

Supply

Sensitivity

Microphone

BASE STATION REPEATER

Speaker Panel

T800//

On

TALK THROUGH

T800-15-0000

SPKR/PROG PNL

TA087-01-0000
100 CHANNEL

CHANNEL PANEL

TA387-01-0000

10 CHANNEL

CHANNEL PANEL

or

or

REAR VIEW

BATTERY ISOLATION LABEL

Duplexer mounted behind

T800-50-0001

OFF

ON

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

DC

FUSE

10A

TYPE

SER NO.

QTY

1T991-05-0100 CASE, PORTABLE REPEATER - 0100 VERSION
1T800-41-0002 DOUBLE GUIDE KIT
1T800-40-0001 BLANK PANEL AND FIXING KIT
1T800-15-0000 SPEAKER / PROGRAM PANEL
1T800-40-0000 FIXING KIT ONLY
1T800-50-0001 BACKPLANE
2290-00010-48 BATTERY SEALED LEAD ACID 12V 6.5A
1X800-25-0000 STANDARD LOOM ASSEMBLY
1W800-25-0000 WIRING LIST T800-25-0000

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 8
SECTION 4
SECTION 5

T A I T

Radio Communications
Christchurch
New Zealand

4

Reference added

3

Battery details added

2

Diode pack alignment corrected

1

Original

Version

AMM 26/8/99ABB
AMM 30/6/99ABB
AMM 2/6/99ABB
AMM 4/3/99ABB

Drawn DateChecked

TITLE:

T800-25-0000 PORTABLE

DRAWING:

T800-25-0000

T800 Series II Conventional Equipment Section 2

T800-25-0001

A single 25W channel, housed in a portable case with sealed lead acid batteries.
This unit can use an external AC power source.

Operational Characteristics

Single channel

•

Up to 25W output

•

AC and DC operation - Batteries, external AC and DC supply input

•

Speaker / Programming panel

•

DC line fuse

•

Backplane interface

•

Battery Isolation Switch

•

Talk Through Switch

•

Configuration Options

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Antenna

•

Mechanical Characteristics

Portable case to house up to 4 modules

•

Top Mounting Duplexer Tray

•

Size

•

Case Only with Handles and Connectors
Height - 242mm 305mm
Width - 255mm 300mm
Depth - 460mm 460mm

Weight – (rackframe with modules shown)

•

18.3kg

CAUTION: If operating above 15 Watts, front and rear covers must be removed.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

Receiver

T800//

Gating

Gate

Sensitivity

Supply

Line
level

Monitor

Volume

Off
On

Monitor

Mute

EXTERNAL DC BATTERY OPERATION

T8n5 -nn-0200 T8n6 -nn-0200

Transmitter

T800//

Carrier

Line

Sensitivity

Microphone

BASE STATION REPEATER

T800//

On

Supply

TALK THROUGH

T800-15-0000

SPKR/PROG PNL

TA087-01-0000
100 CHANNEL

CHANNEL PANEL

TA387-01-0000

10 CHANNEL

CHANNEL PANEL

Speaker Panel

or

or

REAR VIEW

T800//

BATTERY ISOLATION LABEL

Power Supply

Overload

Standby

On

Power

Duplexer mounted behind

T800-50-0001

1

Output

13.8V
25A
Max.

OFF

PART NUMBER DESCRIPTION

2
3

+

4

-

5

ON

ITEMS SUPPLIED AS STANDARD

AC

I/P

DC

and

FUSE

10A

TYPE

SER NO.

SIGS

QTY

1T991-05-0100 CASE, PORTABLE REPEATER - 0100 VERSION
1T800-41-0002 DOUBLE GUIDE KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-15-0000 SPEAKER / PROGRAM PANEL
1T800-40-0000 FIXING KIT ONLY
1T800-50-0001 BACKPLANE
2290-00010-48 BATTERY SEALED LEAD ACID 12V 6.5A
1X800-25-0000 STANDARD LOOM ASSEMBLY
1W800-25-0000 WIRING LIST T800-25-0000

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 8
SECTION 4
SECTION 5

T A I T

Radio Communications
Christchurch
New Zealand

4

Reference added

3

Battery details added

2

Diode pack alignment corrected

1

Original

Version

AMM 26/8/99ABB
AMM 30/6/99ABB
AMM 1/6/99ABB
AMM 5/3/99ABB

Drawn DateChecked

TITLE:

T800-25-0001 PORTABLE

DRAWING:

T800-25-0001

T800 Series II Conventional Equipment Section 2

T800-25-0002

A single channel with up to 50W output, housed in a portable case with no batteries.
This unit can use external AC or DC power source.

Operational Characteristics

Single channel

•

Up to 50W output

•

AC and DC operation - External AC and DC supply input

•

DC line fuse

•

Backplane interface

•

Battery Isolation Switch

•

Talk Through Switch

•

Configuration Options

Channel Panel

•

Duplexer

•

Coaxial Relay

•

Antenna

•

Mechanical Characteristics

Portable case to house up to 4 modules

•

Top Mounting Duplexer Tray

•

Size

•

Case Only with Handles and Connectors
Height - 242mm 305mm
Width - 255mm 300mm
Depth - 460mm 460mm

Weight – (rackframe with modules shown)

•

25W - 12.55kg
50W - 15.9kg

CAUTION: If operating above 15 Watts, front and rear covers must be removed.

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

Receiver

T800//

Gating

Gate

Sensitivity

Supply

Line
level

Monitor

Volume

Off
On

Monitor

Mute

EXTERNAL DC BATTERY OPERATION

OPTIONAL BLANK

PANEL

or

OPTIONS PANEL

Exciter

T800// T800//

On

Carrier

Line

Supply

Sensitivity

Microphone

TALK THROUGH

BASE STATION REPEATER

OPTIONAL

TRANSMITTER

Power Amplifier

Supply

Low forward power

High reverse power

Power

T800-15-0000

SPKR/PROG PNL

or

TA087-01-0000

100 CHANNEL

CHANNEL PANEL

or

TA387-01-0000

10 CHANNEL

CHANNEL PANEL

REAR VIEW

Power Supply

T800//

Overload

Standby

On

Power

T800-15-0000

SPKR/PROG PNL

or
TA087-01-0000
100 CHANNEL

CHANNEL PANEL

or
TA387-01-0000

10 CHANNEL

CHANNEL PANEL

Duplexer mounted behind

DR1

T800-50-0001

1

Output

13.8V
25A
Max.

PART NUMBER DESCRIPTION

2
3

+

4

-

5

DR2

ITEMS SUPPLIED AS STANDARD

AC

I/P

DC

I/P

FUSE

10A

TYPE

SER NO.

QTY

1T991-05-0100 CASE, PORTABLE REPEATER - 0100 VERSION
1T800-41-0002 DOUBLE GUIDE KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-45-0000 PA (50W) GUIDE KIT
1T800-50-0001 BACKPLANE
1X800-25-0002 RACK KIT
1W800-25-0002 WIRING LIST T800-25-0002

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 4
SECTION 5

T A I T

Radio Communications
Christchurch
New Zealand

12Original

Version

Reference added

AMM 26/8/99ABB
AMM 4/6/99ABB

Drawn DateChecked

TITLE:

PORTABLE REPEATER <=50W

X-DC + AC (NO BATT)

DRAWING:

T800-25-0002

T800 Series II Conventional Equipment Section 2

T800-27-0x00

A dual channel rack with 25 Watt per channel maximum output and Tone Remote /
Alarm outputs.

Operational Characteristics

Dual channel

•

Up to 25W output

•

Speaker / Programming panel

•

Remote / Alarm Panel

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

•

Configuration Options

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

•

installation kit

microphone

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

25W - 20.25kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

EARTH

STUD

T800//

Monitor On / Off

Mode Toggle

Clear
Alarms

Test
(3 sec)

Remote / Alarm

Talk Through

Base Station

Rev Power

Aux 0

Fwd Power

Aux 1

Low Battery

Aux 2

Line Fail

Aux 3

Monitor
Volume

Programming

Port

Power

Supply

Output

13.8V
25A
Max.

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Transmitter

T800//

Gate

Supply

Off
On

Carrier

Line

Sensitivity

Microphone

Supply

Remote / Alarm

T800//

Talk Through

Base Station

On

Rev Power

Aux 0

Fwd Power

Aux 1

Low Battery

Aux 2

Line Fail

Aux 3

Monitor On / Off

Monitor

Mode Toggle

Volume

Clear
Alarms

Test
(3 sec)

Programming

Port

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor

Volume

Monitor

Mute

Supply

Gate

Off
On

T800//

Transmitter

Carrier

Line

Sensitivity

Microphone

Supply

On

Power Supply

T800//

Overload

Standby

On

OPTIONAL

BLANK

Power

REAR VIEW

ReceiverTransmitter Remote

1
2
3

+

4

-

5

T800-54-0000

DR1

DIODE

PACK

FUSE

DR2

FUSE

ReceiverTransmitter Remote

PLUG SKTPLUG SKT

T800-54-0000

BATTERY
BACK-UP

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

TB1

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

T800-11-0004 RACK, FRAME ONLY, ASSEMBLED 2 BATT BACK-UP
T800-41-0003 TRIPLE GUIDE KIT
T800-44-0000 T800 PS GUIDE KIT
T800-54-0000 BACKPLANE RACK REMOTE
X800-93-0001 POWER RAIL (STANDARD)

T A I T

Radio Communications
Christchurch
New Zealand

4
3

Drg name changed

2

Drg No changed, Ref added

1

Original

Version

AMM 26/11/99ABB
AMM 26/8/99ABB
AMM 20/10/98ABB

Drawn DateChecked

QTY

REFERENCE

1

SECTION 4

2

SECTION 4

1

SECTION 4

2

SECTION 5

1

SECTION 3

TITLE:

RACK, DUAL 2X25W, (REMOTE

DRAWING:

T800-27-0x00 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-27-0x01

A single channel rack with 100 Watt maximum output, Tone Remote / Alarm
outputs and AC power supply.

Operational Characteristics

Single channel

•

Up to 100W output

•

Speaker / Programming panel

•

Remote / Alarm Panel

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

•

Configuration Options

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0011

•

installation kit

microphone

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

25W - 12.8kg
50W - 16.55kg
100W - 16.9kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

T800//

Monitor On / Off

Mode Toggle

Clear
Alarms

Test
(3 sec)

Remote / Alarm

Talk Through

Base Station

Rev Power

Aux 0

Fwd Power

Aux 1

Low Battery

Aux 2

Line Fail

Aux 3

Monitor

Volume

Programming

Port

Power
Supply

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Gate

Supply

Off
On

Exciter

T800//

Carrier

Line

Sensitivity

Microphone

OPTIONAL

TRANSMITTER

Supply

On

Power Amplifier

OPTIONAL

BLANK

REAR VIEW

Excellence in Radio
Communications

T800//

Supply

Low forward power

High reverse power

Power

FAN (optional)

PA ReceiverExciter

Excellence in Radio
Communications

T800//T800//

OPTIONAL

DUPLEXER

Power Supply

T800//

Overload

Standby

On

Power

OPTIONAL

BLANK

Remote / Alarm

1
2
3

+

4

-

5

FAN

Optional

DR1

EARTH

STUD

Output

13.8V
25A
Max.

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

FUSE

PLUG SKT

DR2

T800-54-0000

QTY

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED
1T800-41-0003 GUIDE TRIPLE SERIESII KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-45-0000 GUIDE PA 50W SERIESII KIT
2T800-40-0001 BLANKING BRACKET / FRONT PANEL
1X800-54-0000 T803-00-0000 BACKPLANE ASSEMBLY
1X800-90-0000 POWER RAIL (STANDARD)

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

TB1

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 4
SECTION 8
SECTION 5
SECTION 3

T A I T

Radio Communications
Christchurch
New Zealand

3

Drg name changed

2

Drg No changed, Ref added

1

Original

Version

AMM 26/11/99ABB
AMM 26/8/99ABB
AMM 1/6/99ABB

Drawn DateChecked

TITLE:

RACK, SNGL<100W, (REMOTE

DRAWING:

T800-27-0x01 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-28-0x00

A single channel rack with 100 Watt maximum output, and provision for a
High Stability Oscillator to enable the Paging function.

Operational Characteristics

Single channel - Paging

•

Up to 100W output

•

Speaker / Programming panel

•

High Stability Oscillator

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

•

Configuration Options

Duplexer

•

Coaxial Relay

•

Fans - single or double

•

Interfaces to Changeover Module TA703-00-xxxx using TA703-11-0010

•

installation kit

microphone

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

25W - 12.75kg
50W - 16.5kg
100W - 16.85kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

Excellence in Radio
Communications

T800//

OPTIONAL

TRANSMITTER

Power
Supply

HSO

T800//

12.8 MHz

Frequency

Adjust

10.0 MHz

OPTIONAL

BLANK

Supply

Receiver

T800//

Gating

Sensitivity

Line

level

Monitor
Volume

Monitor

Mute

OPTIONAL

BLANK

Supply

Off
On

Gate

Exciter

T800//

Carrier

Line

Sensitivity

Microphone

OPTIONAL

TRANSMITTER

REAR VIEW

PA ReceiverExciter

On

Supply

Power Amplifier

T800//

Supply

Low forward power

High reverse power

Power

FAN (optional)

OPTIONAL

BLANK

T800//

Excellence in Radio
Communications

HSO

Power Supply

T800//

Overload

Standby

On

OPTIONAL

BLANK

Power

PLUG

DR2

T800-55-0000

DR1

EARTH

STUD

Output

13.8V
25A
Max.

1
2
3

+

4

-

5

FAN

Optional

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

FUSE

QTY

1T800-24-0004 RACK, FRAME ONLY, ASSEMBLED
1T800-41-0003 GUIDE TRIPLE SERIESII KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-45-0000 GUIDE PA 50W SERIESII KIT
2T800-40-0001 BLANKING BRACKET / FRONT PANEL
1T800-55-0000 BACKPLANE
1X800-90-0004 POWER RAIL (STANDARD)

REFER TO SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

TB1

REFERENCE

SECTION 4
SECTION 4
SECTION 4
SECTION 4
SECTION 8
SECTION 5
SECTION 3

T A I T

Radio Communications
Christchurch
New Zealand

4

Drg name changed

3

Drg No changed, Ref added

2

Speaker removed
Original

1

Version

AMM 26/11/99ABB
AMM 26/8/99ABB
AMM 30/6/99ABB
AMM 2/6/99ABB

Drawn DateChecked

TITLE:

RACK, SNGL<100W, (PAGING

DRAWING:

T800-28-0x00 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-29-0x00

A dual channel rack with 25 Watt maximum output, to interface to Fylde Trunking
Controller

Operational Characteristics

Dual channel

•

Up to 25W output

•

Speaker / Programming panel

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

•

Configuration Options

Fans - single or double

•

microphone

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

25W - 16.05kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

Excellence in Radio
Communications

T800// T800//

OPTIONAL

DUPLEXER

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor

Volume

Monitor

Mute

Off
On

Supply

Transmitter

T800//

Gate

Carrier

Line

Sensitivity

Microphone

Supply

Speaker Panel

T800//

O
F
F

RX 1 RX 2

On

O
F
F

OPTIONAL

DUPLEXER

BEHIND SPK/PROG

PANEL

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Transmitter

T800//

Gate

Supply

Off

On

Carrier

Line

Sensitivity

Microphone

On

Supply

REAR VIEW

Power
Supply

ReceiverTransmitter

Speaker

Panel

ReceiverTransmitter

Power Supply

Overload

Standby

On

Power

OPTIONAL

BLANK

T800-57-0000

EARTH

STUD

Output

13.8V
25A
Max.

SK102 SK101

1
2
3

+

4

-

5

SK107

SK201

SK109

RV210RV211

PL101

FUSE

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

POWER RAIL (STANDARD)

T800-57-0000

FUSE

SK107

SK102 SK101

SK201

REFER TO SECTION 3

SK109

RV210RV211

OF THE

REFERENCE GUIDE

FOR

PL101

POWER RAIL OPTIONS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

TB1

QTY

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED
2T800-41-0002 DOUBLE GUIDE KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-15-0003 SPEAKER/PROGRAM PANEL WITH 3 POSITION SWITCH
1T800-40-0000 FIXING KIT ONLY
1T800-40-0001 BLANK PANEL AND FIXING KIT
2T800-57-0000 BACKPLANE (FYLDE)
1X800-90-0001

T A I T

Radio Communications
Christchurch
New Zealand

Drawing name changed

12Original

Version

AMM 26/11/99ABB
AMM 2/8/99ABB

Drawn DateChecked

TITLE:

RACK, DUAL 2x25W, (FYLDE

DRAWING:

T800-29-0x00 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-29-0x01

A single channel rack with 100 Watt maximum output, to interface to Fylde Trunking
Controller

Operational Characteristics

Single channel

•

Up to 100W output

•

Speaker / Programming panel

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only

•

x = 1 External DC only

•

x = 2 AC and External DC

•

x = 3 AC and Battery

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery

•

Configuration Options

Fans - single or double

•

microphone

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

25W - 10.7kg
50W - 14.45kg
100W - 14.8kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

Excellence in Radio
Communications

T800// T800//

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

T800// T800//

Gate

Supply

Off
On

TRANSMITTER

Exciter

Carrier

Line

Sensitivity

Microphone

OPTIONAL

Supply

On

Power Amplifier

Supply

Low forward power

High reverse power

Power

(OPTIONAL)

FAN

OPTIONAL

BLANK

Excellence in Radio
Communications

T800//

OPTIONAL

DUPLEXER

T800//

Speaker Panel

REAR VIEW

Power

Supply

Speaker

Panel

PA ReceiverExciter

Power Supply

Overload

Standby

On

Power

OPTIONAL

BLANK

EARTH

STUD

Output

13.8V
25A
Max.

1
2
3

+

4

-

5

FAN

DR1

(OPTIONAL)

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

T800-57-0000

FUSE

SK107

SK102 SK101

SK201

REFER TO SECTION 3

SK108

RV210RV211

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

PL101

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

QTY

1T800-22-0004 RACK, FRAME ONLY, ASSEMBLED
1T800-41-0002 DOUBLE GUIDE KIT
1T800-45-0001 PA (100W) GUIDE KIT
1T800-44-0000 T800 PS GUIDE KIT
1T800-15-0000 SPEAKER/PROGRAM PANEL
1T800-40-0000 FIXING KIT ONLY
2T800-40-0001 BLANK PANEL AND FIXING KIT
1T800-57-0000 BACKPLANE (FYLDE)
1X800-90-0000 POWER RAIL (STANDARD)

T A I T

Radio Communications
Christchurch
New Zealand

12Original

Version

Drg name changed

AMM 26/11/99ABB
AMM 2/8/99ABB

Drawn DateChecked

TITLE:

RACK, SNGL <=100W, (FYLDE

DRAWING:

T800-29-0x01 RACKFRAME

T800 Series II Conventional Equipment Section 2

T800-29-0x02

A dual channel rack with 50 Watt maximum output, to interface to Fylde Trunking
Controller.

Operational Characteristics

Dual channel

•

Up to 50W output

•

Speaker / Programming panel

•

DC line fuse

•

Earth stud

•

Backplane interface

•

Power Supply Options

x = 0 AC only Not Available

•

x = 1 External DC only

•

x = 2 AC and External DC Not Available

•

x = 3 AC and Battery Not Available

•

x = 4 External DC and Battery

•

x = 5 AC and External DC and Battery Not Available

•

Configuration Options

Fans - single or double

•

microphone

•

DC converter

•

Mechanical Characteristics

5 Rack Units x 19” rack to house up to 7 modules

•

Size

•

Height - 222mm
Width - 482mm
Depth - 322mm plus 50mm clearance space

Weight – (rackframe with modules shown)

•

50W - 20.7kg

Rack “Items Supplied as Standard” does not include modules other than those listed
on the drawing.
(Receiver, transmitter, PA, power supply, etc. must be ordered separately.)

Copyright TEL 3/7/00

FRONT VIEW

Supply

Speaker Panel

T800//

O
F
F

RX 1 RX 2

On

O
F
F

Power Amplifier Exciter

T800//

Supply

Low forward power

High reverse power

Power

FAN

(OPTIONAL)

T800//

Gating

Sensitivity

Line
level

Monitor

Volume

Monitor

Mute

Off
On

Gate

Supply

T800//

Exciter

Carrier

Line

Sensitivity

Microphone

T800//

Receiver

Gating

Sensitivity

Line
level

Monitor
Volume

Monitor

Mute

Gate

Supply

Off
On

REAR VIEW

PA Exciter

Receiver

Speaker

Panel

Exciter

T800// T800//

On

Carrier

Supply

Line

Sensitivity

Microphone

FAN

Receiver

Power AmplifierReceiver

Supply

Low forward power

High reverse power

Power

(OPTIONAL)

PA

T800-57-0000

EARTH

STUD

DR1

FAN (OPTIONAL)

DR2

SK107

SK102 SK101

SK201

DC INPUT FUSE

SK108

RV210RV211

PL101

FUSE

ITEMS SUPPLIED AS STANDARD

PART NUMBER DESCRIPTION

T800-57-0000

SK102 SK101

DR3

SK107

SK201

REFER TO SECTION 3

SK108

RV210RV211

FAN (OPTIONAL)

DR4

ONLY 13.8V

PL101

TB1

REFERENCE

QTY

SECTION 4

1T800-11-0004 RACK, FRAME ONLY, ASSEMBLED, 2 BATTERY BACK-UP

SECTION 4

2T800-41-0002 DOUBLE GUIDE KIT

SECTION 4

2T800-45-0000 PA (50W) GUIDE KIT

SECTION 8

1T800-15-0003 SPEAKER/PROGRAM PANEL WITH 3 POSITION SWITCH

SECTION 4

1T800-40-0000 FIXING KIT ONLY

SECTION 5

2T800-57-0000 BACKPLANE (FYLDE)
1X800-91-0002 POWER RAIL (STANDARD)

SECTION 3

OF THE

REFERENCE GUIDE

FOR

POWER RAIL OPTIONS

OUTPUT

MAX

2 AMPS

T A I T

Radio Communications
Christchurch
New Zealand

3

Drg name changed

2

Drg No changed, Ref added

1

Original

Version

AMM 26/11/99ABB
AMM 31/8/99ABB
AMM 3/8/99ABB

Drawn DateChecked

TITLE:

RACK, DUAL 2x50W, (FYLDE

DRAWING:

T800-29-0x02 RACKFRAME

T800 Series
Conventional Equipment

Reference Guide

II

Rack

Power Supply

Options

T800 Series II Conventional Equipment Section 2

Power Supply Options

This section details the Power Supply Options for T800 SeriesII Conventional
rackframes. The power rails have been standardised to allow versatility in the rack
applications.

Not all options are available on every rack. Please contact TEL if you are unsure of
the correct option.

Baan Codes

X800-90-0000RAIL<=100W,ACfor1supply
X800-91-0000RAIL<=100W,AC+X-DCfor1supply
X800-92-0000RAIL<=100W,ACfor1supply
X800-93-0000RAIL<=100W,AC+BATfor1supply
X800-94-0000RAIL<=100W,X-DC+BATfor1supply
X800-95-0000RAIL<=100W,AC+X-DC+BATfor1supply

X800-90-0001RAIL,2x25W,ACfor2supply
X800-91-0001RAIL,2x25W,AC+X-DCfor2supply
X800-92-0001RAIL,2x25W,ACfor2supply
X800-93-0001RAIL,2x25W,AC+BATfor2supply
X800-94-0001RAIL,2x25W,X-DC+BATfor2supply
X800-95-0001RAIL,2x25W,AC+X-DC+BATfor2supply

X800-90-0002RAIL,2x50W,ACfor2supply
X800-91-0002RAIL,2x50W,AC+X-DCfor2supply
X800-92-0002RAIL,2x50W,ACfor2supply
X800-93-0002RAIL,2x50W,AC+BATfor2supply
X800-94-0002RAIL,2x50W,X-DC+BATfor2supply
X800-95-0002RAIL,2x50W,AC+X-DC+BATfor2supply

X800-90-0003RAIL,COMBI,ACfor2supply
X800-91-0003RAIL,COMBI,AC+X-DCfor2supply
X800-92-0003RAIL,COMBI,ACfor2supply
X800-93-0003RAIL,COMBI,AC+BATfor2supply
X800-94-0003RAIL,COMBI,X-DC+BATfor2supply
X800-95-0003RAIL,COMBI,AC+X-DC+BATfor2supply

Copyright TEL 14/07/00

Power Rails Numbering System

10/07/2000

System

Type

0 =

AC only

1 =

External DC only

2 =

AC and External DC

3 =

AC and Battery

4 =

External DC and Battery

5 =

AC, External DC and Battery

Power

Rail

9 0 0 0 y

Input

Supply

Output
Supply

-x-T800

0 =

1 supply, up to 100 Watts

1 =

2 supplies, up to 25 Watts/channel

2 =

2 supplies, up to 50 Watts/channel

3 =

2 supplies, combination 50W / 25W

AC POWER SUPPLY ONLY

X800 - 90 - 0000

x = 0

x = 1

x = 2

EARTH

STUD

EARTH

STUD

EARTH

STUD

EXTERNAL DC SUPPLY ONLY

X800 - 91 - 0000

DC INPUT FUS E

AC POWER SUPPLY AND EXTERNAL DC

X800 - 92 - 0000

DC INPUT FUS E

DIODE

PACK

FUSE

TB1

TB1

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

x = 3

x = 4

x = 5

EARTH

STUD

EARTH

STUD

EARTH

STUD

AC POWER SUPPLY AND BATTERY

X800 - 93 - 0000

DIODE

PACK

FUSE

OPTIONAL
POSITION

BATTERY
BACK-UP

EXTERNAL DC AND BATTERY

X800 - 94 - 0000

DC INPUT FUSE

DIODE

PACK

OPTIONAL
POSITION

BATTERY
BACK-UP

AC POWER SUPPLY EXTERNAL DC AND BATTERY

X800 - 95 - 0000

DC INPUT FUSE

DIODE

PACK

OPTIONAL
POSITION

BATTERY
BACK-UP

TB1

TB1

TB1

OUTPUT

ONLY 13.8V

MAX

2 AMPS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

OUTPUT

ONLY 13.8V

MAX

2 AMPS

T A I T

Radio Communications
Christchurch
New Zealand

Diode position changed

12Original

Version

AMM 26/10/99ABB
AMM 8/9/99ABB

Drawn DateChecked

TITLE:

X800 - 9x - 0000

POWER RAIL OPTIONS for T800 RACKS

DRAWING:

power rails.vsd

T800 Series
Conventional Equipment

Reference Guide

II

Guide

Assemblies

T800 Series
Conventional Equipment

Reference Guide

II

Rack

Backplanes

T800 Series
Conventional Equipment

Reference Guide

II

Personality

Boards

T800 Series
Conventional Equipment

Reference Guide

II

Ancillary
Modules

T800 Series
Conventional Equipment

Reference Guide

II

Modules